SPECIAL REPAIRS TO BLDG NO P-16/01 TO P-16/06 AT OLD VETERINARY LINE, SPECIAL REPAIRS TO BLDG NO P-20 (CR SECTION) AT HQ MB AREA AND SPECIAL REPAIRS TO JCOS MD ACCN BLOCK NO 93 AT GURUNG ENCLAVE 1 TTR, 1 STC OF AGE B/R-I UNDER GE (WEST) JABALPUR

Amount

Taking down Cement Plaster any description on brick or stone walls or concrete surfaces including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and as directed.

Taking down shutter of any description n exc 1 sqm each and removing to store complete all as specified and directed.

Demolition of Brick / Stone Masonry built in Cement Mortar including all quoins arches pillars etc complete all as specified and as directed.

Dismantling Timber Scantlings 40 Sq.cm and over in section, in any position, unframed complete all as specified and as directed.

Dismantling of plain/ corrugated AC sheeting, any gauge, thickness, incl nainital or similar pattern roof covering complete.

Dismantling of Stone slabs and tiles of any description or thickness in floors aprons etc complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for, etc., completed all as specified and as directed.

Dismantling Floor, Hearth or Wall Tiling including cement mortar bedding [but not backing] and removing serviceable tiles to the stores and removing rubbish / debris of the premises complete all as specified and as directed.

Demolition of Unreinforced Cement Concrete in ground floors and Pavings not exceeding 15cm thick [below or above ground level] complete all as specified and as directed.

Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete ) set in cement mortor for 150 mm internal dia of pipe complete all as specified and as directed.

Taking down chowket or frame with shutter (without taking off shutters from the frame) area not exceeding 1.5 Sqm each complete all as specified & directed.

Taking down chowkhat or frame with shutter (without taking off shutters from the frame) area exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified & directed.

Taking down or up steel tubing and connections for 15 mm bore of pipe complete all as specified and as directed.

Taking down or up steel tubing and connections for 20 mm bore of pipe complete all as specified and as directed.

Taking down or up steel tubing and connections for 25 mm or 32mmbore of pipe complete all as specified and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes,bends, swan necks etc. complete all as specified and as directed. Note : Measurement shall be of overall as fixed along the centre line over fittings and accessories.

Dismantling water storage tanks exc 250 and n exc 500 ltr capacity complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets including E- Grid frame work complete all as specified and directed.

Demolition of Reinforced Cement Concrete [reinforcement cut as required to facilitate demolition] of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in Soft / Loose soil, complete all as specified and as directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick of excavated soil complete all as specified and as directed. Note: A deduction of 10% shall be made from total computed volume of filling to cater in bulk irrespective of machinery used for ramming.

Removing excavated soils n.exc. 50m and depositing where directed at a level n.exc. 1.5m above the starting point complete all as specified and as directed.

M & L for PCC 1:4:8, Type D-2, using 40mm graded stone aggregate as in Foundation, Filling, Mass concrete, Footings etc complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate as in insertion of hold fast, copings, kerbs, and the like all as directed incl necessary form work complete all as specified and directed.

M&L for providing precast Reinforced cement concrete 1:2:4 type B-1 (using 20mm graded stone agg) for landings, chajjas, and similar articles with plain faces etc. with plain fair faces, including chamfers, weatherings, throating etc. and setting in mortar complete with joints to match the shade set in CM 1:4 including necessary form work complete.

M&L for providing of RCC 1:1.5:3 type A-1 (using 20mm graded stone agg) for landings, shelves, chajjas, and similar articles with plain faces etc. with plain fair faces, including chamfers, weatherings, throating etc. and setting in mortar complete with joints to match the shade set in CM 1:4 including necessary form work complete all as specified and directed.

Supply only liquid integral water proofing compound complete all as specified and as directed.

M&L for Brickwork with subclass ‘B’ bricks, old size straight or curved on plan exc 6 mtr mean radius and built in CM 1:6 complete all as specified and as directed.

Brickwork with subclass ‘B’ bricks, old size straight or curved on plan to any radius in half brick thick walls built in in CM 1:4 complete all as specified and as directed.

M&L for Cutting holes in brick walls exc half brick and nexc one brick in cement in mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 complete all as specified and as directed.

Cutting chases in brick walls, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth complete all as specified and as directed.

M&L Fromwork to Soffiting of Suspended slab in rough surface such as roof slab,floor slabs landing and similar work not exceeding 200 mm thickness as directed by Engr-in-Charge

M&L for 35 mm thick second class hardwood moulded flush door with pre pressed lamination on both side , solid core constructionall as specified in SSR Part-I section 8, clause 8.20 (b) complete all as specified and as directed.

M&L for 35 mm thick second class hardwood mouldedGlazed/gauzed door with pre pressed lamination on both side , solid core construction & prepared to receive glass/ Wiremesh all as specified in SSR Part-I complete all as specified and as directed.

S&F PVC moulded door frame of size 50mm x 47mm made out of 5mm plain coloured PVC sheet reinforced with MS square tube supplying & fixing in opening but single pre laminated PVC sheet used instead of plain colour PVC sheet as per specifications complete all as specified and as directed.

S&F Factory Made Solid PVC Moulded Door Shutters with particle board core 28 to 30 mm thick (stile:), with 2,4 or 6 raised panel design with 2mm thick Moulded PVC Sheet on the front Face & 2mm Plan colour PVC sheet on back face, supplying & fixing in frame at site as per specification & drawing,Solid PVC Moulded Door

M&L for Factory made solid panel PVC moulded glazed/skelton door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F, Mild steel pressed handles 150mm size, oval type, stove enamelled black complete all as specified and directed.

S&F, Mild steel barrel tower bolts 150mm size, stove enamelled black, with bright bolt and fixed complete all as specified and directed.

S&F aluminium anodised, barrel tower bolts of extruded section with length of bolt 150 mm complete all as specified and as directed

S&F aluminium anodised, barrel tower bolts of extruded section with length of bolt 100 mm complete all as specified and as directed

S&F in repair mild steel helical door spring 150mm ordinary rat tail type incl roller and roller plate complete fixed with screws to wooden frames or with welding to steel frames complete all as specified and directed by Engr-in-charge.

S&F in repair mild steel helical door spring 300mm ordinary rat tail type incl roller and roller plate complete fixed with screws to wooden frames or with welding to steel frames complete all as specified and directed by Engr-in-charge.

S&F 300mm long mild steel sliding door bolts plate type stove enameled black with bright bolt not less than 12mm dia with and incl a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate, length of bolt 300mm complete all as specified and directed by Engr-in-charge.

S & F for 100 mm size, medium weight Butt Hinges, cold rolled, mild steel including fixtures complete all as specified and as directed.

S&F extruded aluminium alloy handles, fabricated type, anodised of size 150 mm complete all as specified and as directed.

S&F extruded aluminium alloy handles, fabricated type, anodised of size 100 mm complete all as specified and directed.

S&F 150 mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel spring complete all as specified and directed.

S&F 40-50 mm long floor door stopper of aluminium alloy body and tongue with hard drawn steel spring complete all as specified and directed.

S&F Handles of senso (as per 3D designs) 150mm including all connection fitting complete all as specified and as directed.

S&F in repair stainless steel hinges of 75mm for cupboards of senso (as per 3D designs) including all connection fitting complete all as specified and as directed.

S&F stainless steel wire cloth 0.50 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staple/ wooden beads complete all as specified.

S&F stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staple/ wooden beads complete all as specified.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staple/ wooden beads complete all as specified.

S&F for mild steel pipe 25 mm dia Drapery rod fancy type with PVC coating fixed in the MS hooks, and finials/ side brackets (both side), shade as approved by GE all as specified.

S&F for fancy type knob suitable for 25mm dia dropery rod complete all as specified.

S&F door seal ubber of size n exc 1.00 mtr length complete all as specified and as directed.

S&F factory made steel windows with side hung shutter including box type hinges with steel handle and steel peg stay, complete with glazing bars, dovetailed or welded complete all as specified and as directed.

S&F factory made steel windows with side hung shutter including box type hinges with steel handle and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

S&F steel ventilator factory made with top hung shutter including hinges steel peg stay complete all as specified and as directed.

M&L for box type section of 1.25mm thick for door frame for fixing of door shutter of single channel etc complete all as specified and as directed.

M&L for box type section 1.25mm thick for fixing of door shutter of double channel etc complete all as specified and as directed.

M & L for Rolled mild steel framed work conforming to Fe 410-W (Gde E-250) quality 'A' as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete drilled for fixing of steel gate sheeting or other covering, doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete all as specified.

S&F rolled mild steel structural work in tubular trusses (frames), trussed, fixed with and including special shaped washer etc.complete using ERW or including butt welded tubes confirming to IS 1161-1998 complete all as specified and as directed.

M&L MS work as in wind ties for roof including securing bolts, drilling holes, notching for wire etc complete all as directed.

S&F rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to a common rafters, fixed with angle cleats or other connecting plates of Gde fe 410-W or E 250 (quality A) complete all as specified and as directed.

S & F reinforcement using TMT steel bars of 6mm to 8mm dia, cut to length, bent to shape required including cranking, bending, spirally for hooping,stirrups,hooking ends and binding with annealed mild steel wire not less than 0.9mm dia or securing with clips or welded complete all as specified and as directed.

S&F of aluminium powder coated section, as in frame for door, window, ventilators,fix glazing and partitions of standard section and thickness as directed , cut and jointed together with cadium plated steel screws, plugs for fixing screws, etc. complete all as specified and as directed by the Engineer-in-Charge. Note-(i) Fixing of frame shall be as per manufacturers instructions and all fitting shall be paid under this item. (ii) Thickness of powder coating shall not be less than 50 micron. (iii) Frame shall be one or more rebate as per requirement at site.

Supply and fixing for aluminium alloy (powder-coated) door shutters with hollow aluminium sections as specified including aluminium powder coated snap type beads, dish type door handles, glazed clip joint cleats, rubber gasket, Mortice lock 4 levers (vertical type), two numbers of aluminium alloy anodized tower bolts 200mm long to each leaf, etc. including fixing frame to wall/RCC members with rawl plugs complete. Sections of doors shall be aluminium hollow sections as follows : - (a) Shutter top 83.50mmx44.45mmx1.87mm thick. (b) Shutter bottom 104.00mmx44.45mmx 1.80mm thick (c) Shutter vertical 83.5mmx44.45mmx1.87mm thick (d) Shutter middle 100.00mmx 44.45mmx 2.00mm thick (e) Gauging clip weighing not less than 0.097kg/metre (Note : 1. The rates shall be inclusive of provision of and fixing of rubber packing/gasket. 2. Glass pane shall be measured and paid separately.)

Supply and fixing for aluminium alloy powder-coate) window frame with shutters open able type, with aluminium sections as per of “Jindal” section numbers for casement windows including aluminium alloy snap type beads, handles, aluminium barrel tower bolts and glazing clip, joint cleats, rubber gaskets etc., complete all as specified for series-B “ Jindal” section numbers for casement (a) Section for shutter 47.62x44.45x1.87 mm thick (b) Glazing clip weighing 0.259kg/mtr. (c) Windows shall be provided with 02 Nos. of tower bolt of size 125mm for single leaf shutter and 03 Nos. for double leaf. Handles shall be aluminium ‘D’ type handle of size 98mm and thickness 2.37mm weighing 0.875kg/mtr and 01 No on each openable leaf shall be provided. (Note : 1. The rates shall be inclusive of provision of and fixing of rubber packing/gasket. 2.Glass pane and wire gauge shall be measured and paid for separately.

S&F for 1.25mm thick mild steel, plain, black sheet in hearths; covering to door shut ters; covering to door chowkats (frames); chullah hoods; water tanks; water troughs; ducts; urinal troughs and funnels, etc. cut to size edges beaded if directed, holes punched; including round headed screws, clout nails or rivets and fixed to wood or steel members, etc., with plain 40 mm lap joints or welded/ riveted seams including bending, turning up, mitred angles, stopped ends, outlets, etc. as required complete all as specified and as directed.

M&L Pre-painted galvatume aluminium zinc coating GI based corrugatged steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified

M&L Pre-painted galvatume aluminium zinc coating GI based plain steel sheet 0.5mm thick of an colour having tensile strength of 550 Mpa as in roof covering /cladding to wall, fixed with self tapping screws as specified

M&L for complete removal of existing water proofing treatment from top of roof and canopies / chajjas of building including removal of debris out side MD land complete all as specified and as directed .

M&L for 10 mm thick screed bed or bedding layer in CM 1:3 mixed with water proofing compound as per manufacturers instructions on concrete roof surfaces finished fair and even to maintain the proper slope of roof surface etc complete all as specified and as directed. Note: WPC shall be measured & paid seperately

M&L for Complete removal of existing water proofing treatment from roof and providing water proofing treatment over cleaned roof surface with super thermo APP modified water proofing memberane comprising of the following for Non approachable roofs- (i) Cleaning and sweeping and washing down with water to remove all dust etc from plastered roof surfaces / walls and filling of crack with sealing compound etc (ii) Bituminous based primer conforming to IS: 3384 – 1965 @ 0.3 Kg/Sqm (iii) One layer of super thermo APP modified water proofing memberane with non polyester reinforcement of any make.( M/s STP texsa ltd/Hyperplas memberane of M/S IWL India ltd/MS STPand Tikki Tar ltd). (iv) 3mm thick and minimum Weight @3.50Kg/Sqm,laid with gas torch and pasted on roof surfaces with roller. The over laps shall be sealed by flame including vertical surface after cutting necessary grooves and making good with PCC gola 1:2:4 type- B1 etc adhere to bitumen all as per manufactures instructions. (v) Applying two coat of aluminum paint @ 0.20 Kg / Sqm in two coats over bitumen layer as per manufacturer instruction . (application including sides lap,over laps shall be provided not less than 10 cm and joint sealed with torch as per manufactureerr's instructions specifications and as per particular specifications complete all as specified and as directed.

S&F in repair 18 mm thick PVC sheet one side prelaminated of approved texture ("celuca ply of Rajshree make or equivalent in "Sintex" as approved by GE) as in Kitchen cabinet. (with shelves and partitions) including necessary fitting & fixture as per manucture's instructions complete all as specified and as directed.

S&F, in repairs, 18mm thick ply, PVC sheet of approved texture ("Celuca Ply of Rajshree make or equivalent in "Sintex" as approved by GE) as in Kitchen cabinet and cupboard etc (with shelves and partitions) including necessary fittings & fixtures as per manufacturer's instructions complete all as specified and as directed.

S&F suspended prepainted false ceiling, self design, self texture, using E grid exposed suspended system, grid section size 600mm x 600mm comprising of GI powder coated main runner of dimensions 39mm x 24mmx 08mm thick (thickness comprising of GI /0.4+PPPCGS/0.3mm & weight of runner 1.35 Kg for 3600mm length) cross tee of dimensions 29mm x 24mm 0.8mm thick and thick wall angle 22.2 mm x 22.2mmx 0.65mm thick (thickness comprising of GI /0.35+PPPCGS/0.3mm & weight of angle 0.70 Kg for 3050mm lenght) with and including 4mm thick HPSC (high pressure steam cured) pre-primed, self embossed, texture designer board, water resistant termitant, fire resistant for insulation and acoustic purpose to be placed in the grid systemduly suspended with 4mm dia GI bar hangers fixed with steel dash through fasteners from purlins of the roof with butterfly clips (wt - 0.007 Kg/clip) hold down clips (wt-0.0035 Kg/clip) with provn of light fixture complete all as specified and as directed.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors including 15 mm thick screed bed in CM 1:6 for laying floor finish complete all as specified and as direcred.

M&L for glazed ceramic coloured tiles of size 450 x 300 x 6 to 7 mm, 450x350 or 350x250 6 to 7mm thick on vertical surfaces such as skirting/ dado etc. ,set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile with & including rendering 10 mm thick cement plaster in cement mortar 1:4 finished rough to receive tiles complete all as specified and as directed.

M & L for 20-25mm thick Machine cut Cudappha stone slab as in cooking platform/ shelf laid over and including 20mm cement screed bed in CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and as directed.

M & L for Granite (Black/Ruby Red ) work (table rubbed and polished) 20 mm thick in cooking platforms incl edge moulding & cutting holes for gas pipe through drill machine and jointed with grey cement slurry and pointed to match the shade of granite stone including grinding and polishing fixed over and including screed bed 15 mm thick in CM 1 : 6 etc complete all as specified and as directed.

M&L for rounding edges of granite stone slabs one edge such as in steps, cooking platforms, counter type WHB platform and other similar situations complete all as specified and as directed.

M&L for Non skid ceramic coloured tiles 9 to 10 mm thick (Square or rectangular) area of Each tile exc 0.18 Sqm but not exceeding 0.38 Sqm, in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles laid over and including screed bed or bedding layer 15 mm thick in cement mortar 1:6 for laying floor finishes complete all as specified and as directed.

M&L for Non skid ceramic coloured tiles 9 to 10 mm thick (Square or rectangular) area of Each tile exc 0.18 Sqm but not exceeding 0.38 Sqm, as in skirting ,dados in vertical surfaces etc and including 10mm thick cement plaster 1:4 complete all as specified and as directed.

M&L Non skid coloured ceramic tiles 7 to 8mm thick square/ rectangular area of each tile exceeding 0.11 Sqm but not exceeding 0.18 Sqm as in floor etc set and jointed in neat cement slurry and pointed in white cement with pigment to match, laid over and including 15mm thick cement screed bed in cement mortar 1:6 complete all as specified and directed.

M & L for 25mm thick PCC 1:2:4, Type B-0, using 12.5mm graded stone aggregate to receive floor finish complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6 type C1 using 20mm graded stone aggregate, as in plinth protection laid in panels and finished even and smooth without using extra cement including necessary form work complete all as specified and directed.

M&L for 100 mm thick PCC (1:2:4) type B-1,using 20 mm graded stone aggregate as in flooring and finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M&L for 150 mm thick PCC (1:2:4) type B-1,using 20 mm graded stone aggregate as in flooring and finishing cement concrete surface even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.

M & L for 150 mm thick, PCC 1:4:8, Type D-2, using 40mm graded aggregate as in Sub base for flooring complete all as specified and as directed.

M & L for 100 mm thick, PCC 1:4:8, Type D-2, using 40mm graded aggregate as in Sub base for flooring complete all as specified and as directed.

M&L for 10mm thick rendering in cement mortar 1:6 on fair faces brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L 15mm thick rendering on fair faces of concrete/brick surfaces in CM 1:4 mixed with water proofing compound as per manufactures instruction finished even and smooth without using extra cement complete all as specified and as directed. Note:- WPC shall be measured and paid sperately.

M & L for rendering 15 mm thick in Cement Mortar 1:6 on fair faces of concrete surfaces finished even and smooth without using extra cement complete all as specified and as directed.

M&L 5mm thick rendering in Cement Mortar 1:3 on Concrete Surfaces of ceiling etc finished surface even and smooth without using extra cement complete all as specified and as directed.

M&L for preparation of newly plastered surfaces and applying three coat of white wash as in ceilling complete all as specified and as directed.

Preparation of old surfaces of ceiling and applying two coats of white wash complete all as specified and directed.

M&L preparation of new plastered surfaces of wall and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified and directed.

M&L applying two coats of cement based paint on old decorated surfaces incl preparation of surfaces complete all as specified and directed.

M&L preparation of new plastered surfaces of wall and applying two coats of exterior emulsion paint over a coat of alkali resistant primer complete all as specified and as directed.

Complete removal of existing surface and applying exterior emulsion paint over a coat of Primer on old decorated surfaces incl preparation of surfaces complete all as specified and directed.

M&L for preparing new plastered or un-plastered surfaces of walls and applying two coats of oil bound distemper with 2mm thick wall care putty over a coat of chalk whitining on walls complete all as specified and as directed.

M&L for preparation of old decorated surfaces of walls by complete removal of existing treatment and applying two coats of oil bound distemper over 2mm thick birla wall care putty over a coat of chalk whitining on walls complete all as specified and directed.

S&F 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane complete all as specified and as directed.

S&F 3mm thick figured glass, pin headed type and glazing with oil putty in square n. exc 0.5 sqm in each pane complete all as specified and as directed.

M&L Preparing old wooden surfaces exceeding 10Cm in width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

M&L Preparing old steel surfaces exceeding 10Cm in width or girth and applying two coats of synthetic enamel paint complete all as specified and as directed.

M&L for Preparation of new steel surfaces of any description over 10 cm width or grith and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for Preparation of newly wooden surface of any description over 10 cm width or grith and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors for 16mm (outer dia) bore of pipe including Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor and all necessary fittings etc complete all as specified and directed.

Supplying and laying of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors for 20mm (outer dia) bore of pipe including Brass elbow, Brass Tee, Male threaded brass adaptor, Female threaded brass adaptor and all necessary fittings etc complete all as specified and directed.

S&F 25mm bore tubes medium grade galvanized with all fitting such as socket, elbow, Tee tee, union and short length etc. and fixed complete to walls and ceilings or laid in floors of any length all as specified and directed by Engr-in-charge.

S&F chromium plated single lever wall mixer with connecting legs and wall flange complete all as specified and as directed.

S&F in repair for 15mm chromium plated brass CP mixer of WHB for mixing hot and cold water screwed down for iron pipe and fixed complete all as specified and as directed.

S& F in repairs Stop valve / Angle valve fancy type cast copper alloy chromium plated screwed down high pressure with capstan heads screwed both ends for iron pipe or for union and fixed 15mm bore complete all as specified and directed.

S&F 15 mm concealed type stop valves, cast copper alloy screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed but fancy type, chromium plated with long shank and cup complete all as specified and directed.

S& F in repairs 15 mm bore bib tap cast copper alloy, chromium plated, long body fancy type with capstan headed, screwed down, screwed for iron pipe complete all as specified and directed.

S&F in repairs kitchen plate rack made of stainless steel 0.63mm thick complete size 900 x 750mm x 220mm width of trade pattern complete all as specified and as directed.

S&F for Soap dish, stainless steel of size 160mm x 160mm x 90mm complete all as specified and as directed.

S&F in repair PVC connection pipe of 450 mm long, 15mm size with PTMT nuts complete all as specified and as directed.

S& F in repairs chromium plated shower rose 125 mm size and 15mm dia with or without swivel joints including fixed to pipe or union complete all as specified and as directed

S & F in repairs Towel rail 600 mm long and 20 mm dia brass chromium plated 'D' type fixed with screws and wooden or plastic cleats complete all as specified and as directed.

S&F in repair vitreous China squatting pan of pattern Orissa Pan, size 580 x 440 mm white with integral foot rests any pattertn (excl flushing cistern and flush pipe) complete and including provision of lime concrete bedding, connection to flush pipe, trap etc and making good complete all as specified and as directed.

S&F PVC 10 litres capacity valveless ,syphonic action type low level flushing cistern ,white including flush pipe, cantilever brackets ,inlet, ball valve, float and handle, PVC connection 32mm dia, 450mm long etc complete all as specified and directed (Make: PRAYAG / CERA/ Parryware/Jaquar).

S & F in repairs Vitreous china ware wash hand basin, white, flat back of size 550 mm X 400 mm including brass chromium plated waste fittings with long screw shanks and fly nuts, flange end bedded in red led cement and other end fixed, rubber plug with rings including CI Brackets, cutting for and pinning in ends of brackets or erecting strand, 32mm bore PVC flexible waste pipe etc complete all as specified and as directed.

M&L for 75mm dia PTMT nahani/floor trap plain with grating including jointing with solvent cement complete all as specified and as directed.

S&F in repair Stainless steel sink with draining board, made out of 1.00mm thick sheet for kitchen or laboratory with plug, washers waste pipe, cast iron cantilever brackets, connecting union overall Size 915mmx460mm with bowl size 410mm x330mm x 160mm complete all as specified and as directed.

S& F 500 ltrs rotational moulded polythine water storage tanks (cylinder vertical with closed top) hoisted and fixed in position including ball brass valves, high pressure with polythene float and flynut complete screw for iron pipe or brass ferrule all as specified in SSR Part-I complete all as specified and as directed.

S & F 20mm bore ball valve high pressure PTMT with epoxy coated aluminium rod & high densitypolythene float ball and fly nut screwed for iron pipe complete all as specified.

S&F 20mm dia gun metal, globe or gate valve with iron wheel head screwed both ends for iron pipe and fixed complete all specified and directed

S&F 110 mm dia PVC (SWR ) pipes Single socketed in any length with rubber ring jonits fixed to walls complete all as specified and as directed.

S&F 75 mm dia PVC (SWR ) pipes Single socketed in any length with rubber ring jonits fixed to walls complete all as specified and as directed.

S&F 110 mm dia PVC (SWR) bends any radius with access door complete all as specified and as directed.

S&F 75 mm dia PVC (SWR ) bends any radius with access door complete all as specified and as directed.

S & F in repairs 110 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal with access door complete all as specified and as directed.

S & F in repairs 75 mm bore PVC [SWR] Junction Single [Single "T"] equal or unequal with access door complete all as specified and as directed.

S&F 110 mm bore PVC (SWR) vent cowl including jointing with solvent cement complete all as specified and directed.

S & F stack clamps out of 50mm by 5mm flat iron stays, including bolts and nuts and securing ends of stays to wall or roof for 110 mm PVC pipe etc complete all as specified and as directed.

M&L for laying DWCP 150 mm dia pipes in trenches Class SN-8 conforming to IS 16098 (Part -2) in 6 mtr length with coupler complete all as specified and directed by Engr-in-charge.

M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate complete all as specified and directed.

Taking down carefully any type of old unserviceable point wiring (light, fan, socket bell or power) , complete with fittings such as switches ceiling roses, lamp holders sockets, regulators with PVC conduit surface /concealed or wooden patterns including sunken cast iron /pressed steel terminal boxes etc and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces complete all as specified and directed.

Taking down carefully Main switch and Distribution boards any make and size complete all as specified and as directed .

Taking down the ceiling fan in situ and refixing after servicing, repairing and painting to ceiling fan including scratching old paint and preparation of surface for painting with one coat of white/grey enameled paint complete all as specified and directed.

Taking down the ceiling fan in situ and removing to MES store complete all as specified and as directed.

Taking down carefully Old unserviceable any type sub main wiring with wooden batten/ PVC surface conduit of any size and making good the disturbed surfaces of walls, roof, floors etc to match with the existing surfaces complete all as specified and directed.

M/L for Sub Main Wiring with two single core PVC insulated cable FRLSH of size 6.0 Sqmm multistranded copper conductor FRLSH cable drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 25mm dia with all conduit fitting, fixing accessories and 6 Sqmm multistrand copper conductor FRLSH cable as continuous earth wire complete all as specified and as directed. Note :- Two Nos of 6.0 Sqmm Wire and One No of 6 Sqmm Earth wire in One RM length Measured as one unit length.

M/L for Sub Main Wiring with two single core PVC insulated cable FRLSH of size 4.0 Sqmm multistranded copper conductor FRLSH cable drawing into and including concealed rigid non-metallic PVC conduit, medium grade not less than 20mm dia with all conduit fitting, fixing accessories and 4 Sqmm multistrand copper conductor FRLSH cable as continuous earth wire complete all as specified and as directed. Note :- Two Nos of 4.0 Sqmm Wire and One No of 4 Sqmm Earth wire in One RM length Measured as one unit length.

M&L for Point wiring with PVC insulated 1.5 sq mm multi stranded copper conductor FRLSH cable 1100 volts grade drawn into and including concealed PVC conduit not less than 20mm (ISI marked) including all fitting and fixing accessories including sunk in cast iron/pressed steel terminal boxes duly painted with two coats of anticorrosive paint outside and two coats of aluminium paint inside, 2.8mm thick hylam brand laminated white Bakelite sheet cover for mounting of switches, sockets, fan regulators etc and PVC insulated 1.5 Sqmm multistranded copper conductor FRLSH cable as earth wire and making good the disturbed surfaces to match with the existing surfaces complete all as specified and directed.

(a) One light point/fan point/bell point controlled by one switch.

(b) One socket point controlled by one switch on same board.

(c) One socket point controlled by one switch on Independent board.

All as described in serial item No. 151 here-in-before, but with 1100 volts grade copper standard conductor FRLSH cable of size 2.5 Sqmm with 2.5 Sqmm solid copper conductor cable for 3 pin 15 Amp switch socket outlet independent board complete all as specified and directed.

M&L for Switch piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and as directed .

S & F in repair for bell ding dong AC 230 volts single pole one way complete all as specified and directed.

S & F Socket outlet 3 pin, 5 Amps and AC 230 volts flush type complete all as specified and directed.

S & F in repair for bell push piano flush type AC 230 volts 5 Amps single pole one way complete all as specified and as directed.

S & F switch socket combination 3 pin 5 and 16 Amps AC 230 volts flush type complete all as specified and as directed.

S & F for Ceiling rose surface bakelite 65 mm x 50 mm three terminal AC 230 volts flush type complete all as specified and as directed.

S&F fan regulator Step type of polycarbonate complete all as specified and as directed.

S&F in replacement modular fan regulator, 2 module 4 step 180w heavy duty 230 volts as per existing model/make complete all as specified and as directed.

S&F decorative wall light fitting WITH LAMPS 9 WATT made up of Polycarbonate, City-1, Cylindrical shape, with LED lamp 9 Watt complete with fixing arrangements on wall all as specified and directed. Make:City 1 of havells or equivalent makes mentioned here-in-after.

S & F in repair lamp holder PVC Polycarbonate type body, with back plate for batten fitting icluding 9 watt led lamp complete all as specified and as directed by Engineer in charge. Make: anchor/plaza/leader

S&F in replacement LED light fitting square 57x57 CM Not less than 36 watt along with fixture Surface / Recessed /Pendent mounting LED luminaries with diffuser channel Luminaires ers, connector block, etc . Complete with all accessories internally pre-wired and including round wood block, connecting up with three core flexible flexible copper conductor cable suitable size complete all as specified and directed by Engineer in charge.Make: Philips cat part no: RC375B LED 36S/840 PSU W60 L660 S2 WH or equiv in Luker/havells

S&F LED lamp rotary type/holder type of 12 watt all as specified and as directed.

S&F LED lamp 9 watt all as per required and directed by Engineer-in-Charge.

S & F in repair Sheet metal enclosure DBs Tripple Pole and Neutral 4- way with 200 Amps rated bus bar 240 volts single pole and neutral complete double door complete all as specified and as directed.

S & F MCB TPN 63 Amps, 240 Volts, minimum 10 KA, "C" series rupturing capacity and to be housed in DBs catered here in before complete all as specified and directed :-(Make- Legrand / L&T / Havells)(Note :- Proper and suitable size cablecopper lugs to be fixed with MCBs are included in unit rate of each MCB of any rating)

Supply & Fixing in repair single pole and netural sheet metal enclosure with a two pin and earth plug and socket complete with 01 number single pole MCB 20 Amps complete all as specified & directed. Make:- Legrand/ havells or Equivalent

S&F in repair single pole and netural sheet metal enclosure with a modular type socket complete with 1 number single pole MCB 20 Amps complete all as specified and as directed . Make : Legrand (Cat Part No Ekinox metra plug 5078 11or Havell's /Anchor

Supply & Fixing in repair sheet metal enclosure MCB DB double door [Acrylic], single pole and neutral, 240 volts, 8 way with 200 Amp, 10 KA breaking capacity rated bus bar with blanking plate wherever required and IP-43 degree protection complete all as specified & directed.Make : Legrand CAT NO 507611 / SIEMENS CAT NO 8 GB 32102RC8/GE

S & F for MCB Single pole rated capacity 5 to 40 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as specified and as directed.Make : Legrand cat no DX3 SP 408587,408590,408592,408593,408594,408595 / Siemens cat no- 5SL41067RC, 5SL41107RC, 5SL41167RC, 5SL41207RC, 5SL41257RC, 5SL41327RC / GE

Supply and fixing MCB single pole and neutral 240 volts 40 Amps, B Series complete all as specified and directed by Engineer in chargeMake- Legrand , L&T , ABB.

Supply and fixing in replacement MCB/Isolators single pole 240 volts upto 40 Amps, B Series complete all as specified and as directed.

S&F in repairs Smart bright Batten Series, LED luminaire using LED 22 watt 110 Lumens/watt with diffuser which ensures uniform distribution and comfort, batten series features latest LEDs and delivers consistent light output, stable color start Extruded Aluminium housing, Energy efficient, Flicker free start Inbuilt driver unit, Suitable for wall and ceiling mounting using brackets with and including the luminaire testing on completion as per Standard Specification IEC 60598-2-1 / IS: 10322(Parts/Secl), (Make : Philips Cat part No BN 021 LED 22S 6500/4000 PSU GR S1 or equivalent makes as mentioned here-in-after.

Supply & fix in replacement of LED Security Light Luminaire 35 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens type,GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat , nuts and bolts and painting with aluminium paint. complete all as specified and as directed. Make:Surya cat part no: NGN SLEUL25WIP66 or equivalent makes in PHILIPS and Havells as mentioned here-in-after.

Supply and fixing Single phase propeller type ventilating ( Exhaust fan) heavy duty AC 230 volts 300 mm sweep, metallic body complete with Metalic louvers including making holes of suitable size and making good the disturbed surface and shutters including electric connection with pvc flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.Make:Bajaj,havells or equivalent.

Supply and fixing Single phase propeller type ventilating ( Exhaust fan) heavy duty AC 230 volts 200 mm sweep PVC body complete , including making holes of suitable size and making good the disturbed surface and shutters including electric connection with pvc flexible twin core copper wire from ceiling rose to Exhaust fan, nut & bolt complete all as specified and as directed.Make:Bajaj,havells or equivalent.

Supply and fixing Single phase ceiling fan 1200 mm permanent magnet brushless DC Motor 230 v 50 Hz single phase 26-30watt rated current 0.16 amp,pf 0.98 370/360 rpm air delivery 220m3 rated service value 629m3/min/watt no of blades three type of blade leaf 1.05 mm thick aluminium sheet remote control radio frequency 5 speed +off timer option speed regulation class of insulation two nos bearings including connecting wire complete with all as required and directed at site by eng in charge Make : Havells/ CG/ Bajaj

Supply & fix in replacement of LED Security Light Luminaire 25 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens type,GI pipe 40 mm dia medium Grade not less than with 1.2 m.long in any shape with 2 nos of pole fitting clamps made out of MS flat , nuts and bolts and painting with aluminium paint. complete all as specified and as directed. Make:Havells cat part no: LHDAUU7PA7J025 or equivalent makes as mentioned here-in-after.

M&L for GI Tubes,of size 40 mm dia light grade, galvanised, with all fitting , laid in trenches for protection of cable in road /drain crossing complete all as specified and as directed.

M&L for cuttng of existing road to a required width and depth and making good the surfaces with PCC 1:2:4 type B1 using 20mm graded aggregates after laying the cable through GI pipe etc complete all as specified and as directed.

supply and laying the Brick covering with width equal to length of brick as mechanical protection to cable with well burnt sub class ‘B’ bricks laid dry flat complete all as specified and directed by Engr in charge.

Supply and laying Sand cushioning to under ground cable in trenches/existing cable trenches/ducts in layers of 8 cm deep before laying the cable and 15 cm deep after laying and stretching the cable complete all as specified and directed by Engr in charge. NOTE : Punned thickness only shall be measured and paid.

Earthing complete with galvanised steel earth plate electrode 60 cm x60 cm x 6 mm thick buried directly in ground ,(Earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level ,connected to and including galvanised iron earth wire 4 mm dia by means of nut, bolts, check nuts and washers of galvanised iron or steel complete all as specified and directed including testing on completion including the material and labour of the following : - (a) Excavation and earth work for drilling hole for electrode in any type of Soil. (b) PCC pit in cement concrete 1:2:4 type B-1, Pre cast RCC cover with suitable handle 40 mm thick in PCC 1:2:4 type B-1, reinforced with welded steel wire fabric weighing not less than1.87 Kg/ Sq meter. (c) Funnel with watering pipe of GI 20 mm nominal bore light grade and lugs etc complete all as specified and directed (d) 15 mm nominal bore medium grade GI protection pipe 5 meter long for protection of earthing lead complete all as specified and directed. (e) Requisite quantity of common salt and charcoal. (f) Testing of earthing.

S&F of modular switch 16 AMPS one module 230 volts AC complete all as specified and as directed .

S&F of modular switch 6-10 Amps one module 230 volts AC complete all as specified and as directed .

S&F of modular socket 6A -2/3 pin combined 2 module, 230 volts AC complete all as specified and as directed .

S&F of modular socket 2/3 pin, 6/16 Amps combined two module and AC 230 Volts as per existing model/make complete all as specified and as directed .

S&F in replacement of frame plate for modular switch 1 module including screws and washers etc model/make as per existing in site complete all as specified and as directed.

S&F in replacement of frame plate for modular switch 2 module including screws and washers etc model/make as per existing in site complete all as specified and as directed.

S&F in replacement of frame plate for modular switch 3 module including screws and washers etc model/make as per existing in site complete all as specified and as directed.

S&F in replacement of frame plate for modular switch 4 module including screws and washers etc model/make as per existing in site complete all as specified and as directed.

S&F in replacement of frame plate for modular switch 6 module including screws and washers etc model/make as per existing in site complete all as specified and as directed.

S&F in replacement of frame plate for modular switch 8 module including screws and washers etc model/make as per existing in site complete all as specified and as directed.

S&F in replacement MS Housing box 1/2 module suitable for modular switch as per existing switch box and making good to the disturb surface complete all as specified and as directed.

S&F in replacement MS Housing box 3 module suitable for modular switch as per existing switch box and making good to the disturb surface complete all as specified and as directed.

S&F in replacement MS Housing box 4/5 module suitable for modular switch as per existing switch box and making good to the disturb surface complete all as specified and as directed.

S&F in replacement MS Housing box 6/8 module suitable for modular switch as per existing switch box and making good to the disturb surface complete all as specified and as directed.

S & F in repair of LED Decorative /mirror light fitting 9 watt along with fixture Surface mounted suitable for indoor aplication , connector block, etc . Complete with all accessories internally pre-wired and including round wood block, connecting up with three core flexible flexible copper conductor cable suitable size complete all as specified and directed by Engineer in charge. Make- Havells LUMILINEPLUSSBS10WLED865SPCSS or equivalent makes as mentioned here-in-after.

S & F in repair Bulk head endura LED light fitting complete with10 watt LED and making necessary electric connection to ceiling rose with copper conductor of suiyable size & length complete all as specified & directed. Make :Havells Cat Part No. HEXAFT10WLED857SSYMBOPC or Equivalent make Philips / BAJAJ / WIPRO

Supply & fixing electronic energy meter tamper proof design digital technology of SINGLE phase 1 x 240 volts 50 HZ 0.4% basic current for direct connected meter and 0.2% of basic current for CT operated meter with LCD display class-1 accuracy as per IS : 13779 Microprocessor based single phase energy meter of 10--60 Amp / 5 Amp CT operated with CT with optical communication port complete with all accessories complete with fixing accessories on finished wooden box all as specified & directed at site. Make-Secure SARAL/or equivalent (Prepaid meters)(old meter to be disconnected amd deposited in MES yard)

Supply, installation, testing & commissioning of 1 Phase, 2 Wire, Smart Prepaid Energy Meters, BIS 16444 Marked in existing Meter Board / Floor Panels with Pre Payment Shock Proof capacitive touch Keypad (Similar as IOS and android phone technology), Bluetooth, based Digital having current range 05-60 Amp, 240 V, accuracy class 1.0 along with inbuilt load control switch, containing provision for TOD & RTC, inbuilt feature sense for data transfer (wireless, without DCU, USB, Pen drive) no other extra equipment required for data transfer, meter itself capable for data transfer) capable to define 4 tariff slabs, happy hour & holiday definition, when user go outside of the home, user can punch recharge token on meter keypad and manually and automatic via mobile app. Meter should support the following data’s :- 30 minutes instantaneous data for voltage, current, power factor, power, cumulative energy and frequency, 30 load survey data for energy, monthly billing survey for Cumulative Energy and Max Demand. Meter should have connect / disconnect remotely, functionality operable for prepaid/ post-paid billing software. The meter should support communication protocol NB IOT/ DLMS with the software all as specified and directed. That the manufacturer or their service provider shall furnish 10 (Ten) years replacement guarantee for prepaid meters installed under this contract except demage from water and fire. OEM will be responsible for connectivity and smooth functioning with MES server without any hindrance. including all acceseries if required for imstallation of meter for its smooth and user friendly operation all as per required and directed by Engineer in charge.

Supply , laying and testsilng cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cables ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 3.5 core 35 Sqmm complete all as specified and as directed.

Supply , laying and testsilng cable XLPE insulated , screened, PVC bedded , galvanized , steel strip or wire armoured, electric power cables ( Heavy duty ) 1100 volts grade with stranded aluminium conductor of size 4 core 25 Sqmm complete all as specified and directed by Engineer in charge

Tiki Water proofing Co

Kirti Chandeliya and Assosicates