REPAIRS TO ROOF TREATMENT, FINS, FACIA, CHAJJAS, PLASTER PLUMBING AND SANITARY ITEMS AND WOODEN STEEL, ALUINIUM JOINERY AND ROLLING SHUTTERS IN TECH AREA AT AF STN UTARLAI

Amount

Taking down roof treatment any type any description on top of roof not exceeding 10cm thick including removal of rubbish out side MD and complete all as specified and directed

M&L for cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate as in roof padding benching kerbs of mud stops, rounded or chamfered on edges including form work complete all as specified and directed

M&L for applying roof treatment on top of roof with minimum 3mm thick APP modified membrane with non woven polyester reinforcement (centre core) shall be laid by torch application method with overlap 100mm on length side and 100mm on width side including a coat of bituminous oil based primer ( IS : 3884) @ 250gm / Sqm weight not less than 3 kg/Sqm complete all as specified and directed

M&L for rendering 10mm thick in cement mortar (1:4) on concrete surface as on roof slab, finished even and smooth without using extra cement mix with water proofing compound as per manufacturer instruction complete all as specified and directed Note :- Water proofing compound shall be measured and paid saperately

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc complete all as specified and directed

M&L for 15mm thick rendering in CM 1:4 on brick/concrete wall surfaces finished even and smooth without using extra cement mix with water proofing compound as per manufacturer instruction complete all as specified and directed Note :- Water proofing compound shall be measured and paid saperately

Supply only Integral water proofing compound complete all as specified and directed.

Taking down cement concrete plaster as in brick wall/ stone walls, fin facia chajjas etc (other than ground floors) beam, staircase, landing and similar work complete all as specified and directed

M & L for Dubbing out average 20mm thick in CM 1:4 on irregular face of old walls/ ceiling, fin facia chajjas etc complete all as specified and

M&L for rendering 10mm thick in cement mortar (1:4) on concrete surface as on roof slab, fin facia, chajjas finished even and smooth without using extra cement mix with water proofing compound as per manufacturers instructions complete all as specified and directed

S&F GI chicken wire mesh of 1.80 mm dia wire & 28 mm mesh size fixed with nails & screws around RCC chajjas/facias etc complete all as specified and directed

M&L for preparation on new plaster surface of walls & applying two coat of cement base paint , complete all as specified and directed

Dismantling, floor, hearth or wall tiling including cement mortar bedding (but not backing), and rubbish off the premises complete all as specified and directed

M&L for non Skid ceramic coloured tiles 7 to 8mm thick (square/rectangular) area of each tile exceeding 0.11 but not exceeding 0.18 sqm, in floors etc. laid over & including 15mm thick screed bed in CM 1:6 and set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles complete all as specified and directed

M&L for glazed ceramic coloured joint free tiles of size (450x300 mm) x 7mm thick in dados skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiling laid over & including over 10mm thick plaster in CM 1:4 complete all as specified and directed

Taking up or down existing steel water tubing 15mm bore alongwith connections fixed/laid in any situation complete all as specified and directed

S&F for galvanised iron steel water tubing 15mm bore "medium grade" with all fittings and fixed to wall/ceiling or laid in floors complete all as specified and directed

Taking up or down existing steel water tubing 20mm bore alongwith connections fixed/laid in any situation complete all as specified and directed

S&F for galvanised iron steel water tubing 20mm bore "medium grade" with all fittings and fixed to wall/ceiling or laid in floors complete all as specified and directed

M & L for cutting chases, pinning in, making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10cm girth on stone concrete block or slab wall complete all as specified and directed

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position capacity of tank exc 250 litres & n exc 500 litres complete all as specified and directed

Disconnecting existing tanks, setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position capacity of tank exc 500 litres & n exc 1000 litres complete all as specified and directed

Dismantling water tanks capacity exc 250 litres and n exc 500 litres complete all as specified and directed

S&F 500 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed Note:- PVC tanks shall be ISI marked and having two layers.

Dismantling water tanks capacity exc 500 litres and n exc 1000 litres complete all as specified and directed

S&F 1000 litres capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete all as specified and directed Note:- PVC tanks shall be ISI marked and having two layers.

S&F in repairs 20mm bore ball valve high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed (minimum weight 20mm-210gms)

S&F in repair 20mm bore gun metal globe or gate valve with iron wheel head screwed both ends for iron pipe complete all as specified and directed

Demolition and breaking up drain pipe 75 mm bore salt glazed stone ware/AC/PVC pipe complete all as specified and directed

S&F 75mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls and stack clamps as in rain water pipes complete all as specified and directed

S&F 75mm bore PVC (SWR) bends/shoes any radius complete all as specified and directed

M&L for 75mm dia PVC (SWR) floor trap plain including jointing with solvent cement Complete all as specified and directed

S&F in repairs vitreous china squatting pan Orissa pattern size 580x440 mm white with integral foot rest complete all as specified and directed

S&F in repairs WC pedestal pattern wash down type (European type WC), white or coloured superior quality including plastic seat cover and making good to the disturbed surfaces complete all as directed

S&F in repairs 100 bore cast iron 'P' or 'S' trap with cement joint complete all as directed

S&F in repairs 10 Ltr capacity PVC valve less, symphonic action type flushing cistern low level white with inlet ball valve float & handle including brackets complete all as directed

S&F as in repairs stainless steel grating doom of 100mm dia with / without central hole set over the existing nahani trap/ floor trap in neat cement & pointed to match the floor finished all as directed

S&F in repair vitreous china wash hand basin size 550x400mm including vitreous china pedestal brackets & one No PTMT waste coupling 32 mm size, 15 mm bore a CP cast copper alloy fancy type pillar tap quarter turn type complete flexible PVC waste pipe of suitable length all as directed at site

S&F in repairs vitreous china urinal, half stall type "white" including suitable size pvc waste coupling and pvc waste pipe complete all as specified and directed

S&F in repairs 15mm bore bib tap cast copper alloy chromium plated fancy type crutch or butter fly handle screwed down screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed

S&F in repairs 15mm bore cast copper alloy chromium plated angle valve quarter turn fancy type with flange plate complete all as specified and directed

S&F in repair 15mm bore stop valve of cast copper alloy quarter turn type screwed down high pressure with crutch or butter fly handle fancy type chromium plated, with long shank and cup (concealed type ) complete all as directed

S&F in repair 15mm bore cast copper alloy chromium plated two way angle cock quarter turn fancy type with flange plate complete all as specified and directed

S&F in repair 15mm bore chromium plated health faucet with 1.0 meter long CP flexible pipe complete all as directed

S&F in repair 15mm bore PTMT jet spray for EWC with flexible pipe with PTMT nut & bolt complete all as specified and directed

S&F in repairs stainless steel towel rail round 200mm dia with round flange of standard quality fixed with steel screw and PVC rawl plug complete all as specified and directed

S&F in repairs chromium plated shower rose fancy type with swivel joints including shower arm 15mm dia 195mm long with bend of 45 degree with flange of CP brass complete all as specified and directed

S&F in repairs PVC connection 15mm size with PTMT nuts of length 450mm complete all as specified and directed

S&F in repair urinal spreader of PTMT any colour for fixing with 15mm dia pipe minimum weight 60gms complete all as specified and directed

Taking down and re fixing same opening after easing and adjusting of shutters of any description not exceeding 1 Sqm each, complete all as specified and directed .

Taking down and re fixing same opening after easing and adjusting of shutters of any description exceeding 1 Sqm but not 2.00 sqm each, complete all as specified and directed .

Taking down aluminium door shutter of any size carefully from frames for repairing including replacement of broken pivots, tightening of joints of rails and styles etc complete and refixing in the same opening to obtain smooth functioning of the door complete all as specified and directed.

Taking down PVC chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Sqm each complete all as specified and directed .

Taking down PVC shutters of any description, area not exc 1.50 Sqm each complete all as specified and directed .

S&F Factory made PVC door frame of size 50 x 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed.

S&F factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site as per specification in MES SSR Part - I & II complete all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) of size exceeding 1.50 Sqm but n. exc 4.0 Sqm each complete all as specified and directed .

Taking down shutters of any description, area exc 1 Sqm and not exc 2.00 Sqm each complete all as specified and directed .

S&F factory made 35mm thick flush shutter, solid core construction with block board core and plywood face panels, commercial type on both sides complete all as specified and directed

S&F factory made 35 mm thick, 2nd class hard wood , glazed and skeleton door shutters open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc , size of members as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, complete all as specified and directed.

S&F 35 mm thick factory made plain panelled shutter ( two panel) out lock rail and pane of 9mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated , complete all as specified and directed.

M&L for IInd class hard wood Plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints, supplied and fixed (Back of chowkhats shall be treated with tar or coal tar black paint & cost of same shall be included in the quoted rate of this item)

Taking down aluminium chowkhats or frames with shutters (without taking off shutters from the frames) of size exceeding 1.50 Sqm but n. exc 4.0 Sqm each complete all as specified and directed .

Taking down aluminium shutters of any description, area exc 1 sqm and not exc 2.00 Sqm each complete all as specified and directed .

S & F Anodised aluminium door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges 03 Nos of each door, anodised aluminum snap beading screws etc. complete all as specified. Note: The aluminum snap beading and rubber gasket for fixing to galss panel should be free for fixing and rate to be included in this items.

Taking down aluminium chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Sqm each complete all as specified and directed.

Taking down aluminium shutters of any description, area n. exc 1 sqm each complete all as specified and directed .

S & F Anodised aluminium window and ventilator shutters, side hung /fixed/sliding type/with or without sash bar, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified. Note: The aluminum anap beading and rubber gasket for fixing to galss panel should be free for fixing and rate to be included in this items.

S & F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F aluminum grill of any design and pattern as approved including aluminium beading for proper fixing of grill complete all as specified and directed .

Taking down steel shutters of any description, area not exc 1.50 Sqm each with iron mongry stoppers, cleats etc any type complete all as specified and directed , complete all as specified and directed .

S & F factory made Steel window with side hung shutters including box type hinges with mild steel handle and peg stay complete with glazing bars dovetailed or welded complete all as specified and directed

S & F factory made Steel window with side hung shutters including box type hinges with mild steel handle and peg stay complete with out glazing bars dovetailed or welded complete all as specified and directed .

S&F factory made steel ventilator with top hung shutter including box type hinges , mild steel handle & peg stay with or without glazing bar complete all as specified and directed .

M&L for cutting holes in stone walls built in cement mortar for inserting hold fasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B1 as required , depth of embedded portion of hold fasts or lugs exc, half brick but not exc. one brick from the face of the jamb in to the wall complete all as specified and directed.

M & L for mild steel works in band, straps, supports or stage for rain waters , ventilating pipes including bolts if required hooks (stay) heavy for large gates , hook and pintle hinges,large hasp and staples , chains, hand made sliding bolts clamps, hold fasts , wall ties hooks for hanging fans, plain angle cleats for securing purlins to wood trusses or rafters , knee piece inserts , two and three ways straps , plate washers and similar small articles conforming to grade E-165 (Fe-290) complete all as specified and directed

M & L for framed work such as doors, gates or frame for cooler stand of angle or other section with gusset plates, rails, braces etc, drilled for fixing of sheeting or other covering of door etc, to be prepared for hanging or sliding etc with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other coverings running rails and guides ) conforming to Fe 410- W( Gde E-250) quality A and hanging and fixing complete all as specified and directed.

S&F framed work such as grills, grating, etc. with end of bars shouldered and / or riveted ,or forged into spikes, framed guard bars, barred iron doors, ladders, framed balusters, walkways, railings, frame work of water tanks and similar work conforming to Fe.290. Gde-E-165 complete all as specified and directed

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and and average width of aperture 1.40mm fixed with stainless steel wire staples, complete all as specified and directed

S&F 3mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads, in squares n.exc 0.50 Sqm each pane complete all as specified and directed .

S&F 4mm thick figured (frosted) glass, pin head type and glazing with oil putty in squares not exceeding 0.50 Sqm each pane complete all as specified and directed .

Hacking out old broken glass (any thickness, size, quality or description) from wooden/steel frames, glazed with putty or fixed with beads complete all as specified and directed .

M & L for preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M & L for preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed .

S & F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed.

S & F 250 mm long Mild steel sliding door bolts, clip type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate, complete all as specified and directed.

S & F mild steel mortice lock vertical type size 100mm 4 levers complete all as specified and directed .

S & F stainless steel latches 75 mm long suitable for locking arrangement of PVC door as per sample approved complete all as specified and directed.

S & F Aluminium anodised barrel tower bolt of extruded section, 200 mm long of bolt and fixed with screws, complete all as specified and directed.

S & F 200 mm long Mild steel barrel tower bolts, stove enamelled black, with bright bolt , complete all as specified and directed.

S & F Aluminium anodised barrel tower bolt of extruded section, 150mm long of bolt and fixed with screws, complete all as specified and directed.

S&F 150mm size, aluminium D type purpose made fancy type handle for aluminum door only (cast type) anodized, and fixed with steel screws ,complete all as specified and directed.

S&F 150mm size ,Mild steel pressed handles, oval type, stove enamelled black ,complete all as specified and directed.

S&F 125mm size, aluminium (cast type) anodized, handle and fixed with steel screws complete all as specified and directed

S & F in Mild steel butt hinge, 100mm long, medium weight, cold rolled fixed with steel screws or welded to steel frame where required complete all as specified and directed .

S&F door closer hydraulically regulated designation No 3 universal type suitable for door shutter of 851 to 1000 mm in width of Aluminum body (die cast) weight between 61 to 80 kg complete all as specified and directed .

M&L for 15mm thick rendering in cement mortar (1:6) on brick wall or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed .

M & L for preparation of new plastered surfaces of walls & applying three coats of white wash complete all as specified and directed .

S&F in repairs dust guard vertical venetian blinds of any shade as approved with suitable hanging arrangement, tilting/folding device complete all as approved sample and directed. Make :-Vista/Deck

S&F in repair aluminium door stopper double legged with rubber shoe of size 55 x 70 mm long fixed to door shutters with steel screws complete all as specified and directed .

S&F in repairs 25 mm dia fancy type stainless steel curtain rod bright finish with fancy type side brackets & end cups etc and fixed with PVC rawl plugs & steel screws complete all as specified and directed.

S&F in repairs Stainless steel wire cloth, 0.36mm nominal dia of wire and and average width of aperture 1.40mm fixed with stainless steel wire staples, complete all as specified and directed

S & Fi n repair 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy, complete all as specified and directed.

S & F in repair 200 mm long Mild steel barrel tower bolts, stove enamelled black, with bright bolt , complete all as specified and directed.

S & F in repair Mild steel butt hinge, 75 mm long, medium weight, cold rolled fixed with steel screws or welded to steel frame where required complete all as specified and directed .

S & F in repair Mild steel butt hinge, 100 mm long, medium weight, cold rolled fixed with steel screws or welded to steel frame where required complete all as specified and directed .

S&F in repair 150mm size, aluminium D type purpose made fancy type handle for aluminum door only (cast type) anodized, and fixed with steel screws ,complete all as specified and directed.

S & F in repair mild steel mortice lock vertical type size 100mm 4 levers complete all as specified and directed .

S & F in repairs door closer hydraulically regulated designation No 3 universal type suitable for door shutter of 851 to 1000 mm in width of Aluminum body (die cast) weight between 61 to 80 kg complete all as specified and directed.

S & F in repairs double action floor spring hydraulically regulated made up of minimum 1.25mm thick aluminum alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified and directed .

Taking down steel rolling shutters including hood cover, shaft etc of size exc 5 Sq.M but not exc. 15 Sq.M and assembling and re-fixing after greasing, oiling, minor repair, punch locking arrangement of lath sheets and removing existing lath locking arrangement, replacement of rusted nuts & bolts of rolling shutter complete all as specified and directed. Note :- (i) The unserviceable parts shall be measured and paid for separately. (ii) Quoted rate shall be inclusive of providing missing nuts, bolts, greasing , oiling denting to rolling shutter and hood cover,guide rail and tension to spring etc all as directed.

-ditto- all as per item Ser No 114 above but size exceeding 15 Sq.M but not exc 35 Sq.M complete all as specified and directed.

-ditto- all as per item Ser No 114 above including twisting in springs but without taking down shutters complete all as specified and directed.

-ditto- all as per item Ser No 115 above including twisting in springs but without taking down shutters complete all as specified and directed.

M & L for replacement of mild steel crank handle with rubber grip on handle and weight of standard quality as per sample approved by GE and directed. Note : Mid steel crank handle shall be as per existing size and specification

M&L for replacement of gear box of superior quality as per sample approved by GE for rolling shutters including crank handle with rubber grip, racks, pinion system, bearing etc complete all as specified and directed. Note : Gear box shall be as per existing size and specification

M&L for replacement of ball bearing with bush of suitable dia superior quality of approved make for rolling shutter complete all as specified and directed. Note : Ball bearing shall be as per existing size and specification

M&L for replacement of mild steel high carbon 5 to 6mm dia 32 to 60 cm long spring as per sample approved by GE for rolling shutter complete all as specified and directed.

M&L for replacement of teeth of rolling shutter made of carbon steel (Kirra and Lattoo) as per sample approved by GE complete all as specified and directed. Note : Teeth of rolling shutter shall be as per existing size and specification

M&L for replacement of mild steel pipe 25mm dia high carbon heavy duty grade conforming to IS 1161-1968, including making necessary making hole and nut & bolt etc as per approved sample complete all as specified and directed.

M & L for replacement of mild steel carbon heavy duty anchoring rod of 40/50 mm dia of pipe including suitable size mild steel drum complete all as specified and directed. Note : Anchoring rod shall be as per existing size and specification

S & F in repairs locking arrangements of rolling shutter complete including locking plate of any description including cutting existing locking arrangement by welding and welding new locking arrangement and necessary welding to guide channel if required complete all as specified and directed.

Taking down unserviceable guide channel of rolling shutter of any thickness and providing new MS guide channel of 2 mm thick and 75 mm deep complete all as specified and directed.

S&F in repairs 0.90 mm thick MS hood cover to hexagonal, square or circular in shape fixed in position to bracket plate / angle complete all as specified and dirtected.

Taking down rolling shutters with hood cover complete of any description complete all as specified and directed.

S&F factory made steel rolling shutter with laths of 0.90 mm thick without gear operated as specified including 0.90 mm thick MS top hood cover and anchoring rod, hasps and staple , erected in position as indicated , complete push pull or manual type complete including proper inlocking arrangement of lath strips complete all as specified and directed.

-ditto- all as per item Ser No. 130 above but gear operated type with best quality bevel gear box and crank handle complete all as specified and directed.

-ditto- all as per item Ser No 130 above but 15% lath strips should be fixed with semi perforated complete all as specified and directed.

M&L for preparation of old painted steel surfaces of any description over 10cm width or girth, not otherwise described and applying one coat of synthetic enamel paint complete all as specified and directed.

M & L for preparation of old treated wooden surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for replacement of connecting lath sheet of size not less than 0.30 Mtr wide and 0.45 Mtr long and 0.90mm thick connecting to lath and drum/spring by means of rivets/welding to any size of rolling shutter complete all as specified and directed.

Taking down rolling shutter and removing of old worn out laths strip of rolling shutter and replacement of new 0.90 mm thick semi-perforated lath sheet strip to existing rolling shutter of any size including locking arrangement of new lath and refixed in same position complete all as specified and directed.

S & F MS screw bolts machine made with haxagonal or six head at one end and screwed the others each screwed and to be fitted with washers and one hexagonal or six but exceeding 05 cm but not exceeding 10 cm long, 5 to 10 mm dia of neck complete all as specified and directed .

S&F in repairs 200mm dia heavy duty mild steel wheels of best quality rubber coating on outer dia of wheel with best quality ball bearings, carbon steel safety pin etc complete including all necessary fittings mild steel roller at top for support and balancing of steel gate and MS flat Iron required for welding of wheel to iron gate and making smooth functioning of tech area main gate complete all as approved by GE and directed. (Note :- (i) Rate deemed to be included by contractor for necessary T & P arrangement for change of wheel). (ii) All safety measures shall be taken by the contractor as per safety code

Taking down aluminium partitions of any description complete all as specified and directed .

S & F Anodised aluminium frame for partition with one or more rebates including joining cleat for fixing etc. complete all as specified. Note: The aluminum anap beading and rubber gasket for fixing to galss panel should be free for fixing and rate to be included in this items.

S & F 12mm thick Prelaminated particle board, exterior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination, fixed with screws to aluminum frame work, complete all as specified and directed.

Dismantling of Wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/slabs/ blankets, any thickness, including cover fillets

S&F Anodised aluminium snap grid of size 605 x 605mm frame work for false ceiling all as specified Note:- Size of anodised aluminium sections shall be as per clause No. 10.38 on page No. 216 of Section 10 of SSR part-I 2009

S&F 12 mm thick Perforated particle board/ tiles for insula-tion and accoustic purposes, 60x60 cm in size, fixed with nails to timber framework or with staples or on snap grid as in ceiling , complete all as specified and as directed.

Dismantling of Asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings including wird tile complete all as specified and directed.

S & F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with fixed with self tapping screws as specified specified

S & F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with fixed with fixed with self tapping screws specified

S&F mild steel flat iron as wind ties of grade Fe-290 Gde-E-165 or roof including drilling holes securing bolts etc and similar work complete all as specified and directed

KRISHNA CONSTRUCTION COMPANY