SPECIAL REPAIR TO STRUCTURAL SAFETY TO BUILDING NO P 49 AT CIVIL ZONE SPECIAL REPAIR TO C BLOCK OF SNCOs MESS AT CAMERO COMPLEX AND PROVN OF RAIN WATER DRAIN AT OMQ MAP AREA UNDER GE AF SUBROTO PARK DELHI CANTT 10

Amount

Taking down cement or cement lime plaster on brick walls incl racking out joints hacking for key scrubbing down with water etc complete as specified and directed by Engr-in-Charge.

M&L Rendering 15mm thick in cement mortar 1:6 on other than fair faces of brick work or concrete surfaces of walls, finished even and smooth ( without using extra cement) complete all as specified and directed by Engr-in-Charge.

M&L for rendering CM (1:4) 15 mm thick using water proofing compound @ 2% of weight of cement as per manufactureres other than fare faces of brick surface or concrete surfaces even and smooth without using extra cement complete all as specified and directed by Engineer-in-Charge.. (Note : WPC shall be measured & paid separatelly)

M&L for rendering cement mortar (1:4) 10 mm thick on concrete surfaces of ceiling, even and smooth without using extra cement Complete all as specified and as directed by Engr-in-Charge.

M & L for complete removal of existing treatment of surfaces by steel wire brushing, scraping down smoke soots, moulds, moss and efflorescent salts etc on wall and applying two coats of oil emulsion distemper over a coat of primer including 3mm thick wall care putty on wall complete all as specified and as directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces of walls, and applying two coats of distemper oil emulsion over a coat of primer incl 3mm thick elastomeric wall care putty on walls complete all as and directed by Engr-in-Charge.

M&L for preparation of new plastered surfaces of walls, and applying two coats of cement based paint over a coat of primer complete all as specified and directed by Engr-in-Charge.

M&L preparation of new plastered or unplastered surface and applying three coats of white wash on ceiling omplete all as specified and directed by Engr-in-Charge.

Demolition of cement concrete including brick tiles/APP mebrane of any description and in any position not otherwise specifically provided for including removal of same to a distance of 30Km (outside MOD land) complete all as specified and as directed by Engr-in-Charge.

M&L five layered prefabricated Atactic polypropylene Polymer (APP) modified 3mm thick membrane (weighing not less than 3 Kg/Sqm) reinforced with 160gsm polyster non-woven fabric . Concrete of roof surface shall be scratched with scratching tool before finishing roof surface. When the concrete surface is still green, 10mm thick 1:4 cement plaster shall be laid including liquid water proofing compound as per manufacturers instructions (WPC will be measuerd and paid seperatly). The roof surface shall be throughly wire brushed, washed, dried up and cleaned of all foreign matter and dust prior to the application primer. On the dried surface one coat of approved bituminoius primer, having density in the range of 0.87 to 0.89 Kg/Litre at 25 degree centigrade and viscosity of 70 to 160 CPS, manufactuered @ 0.4 Litre/ Sqm shall be applied. APP membrane shall be laid on primed surface by torch application method after allowing 24 hours for primer to dry. Laying of APP membrane shall be commenced at the lowest level and worked upto the crest. APP allowing 24 hours for primer to dry. Laying of APP membrane shall be commenced at the lowest level and worked upto the crest. APP membrane will normally be laid in length at right angle of the direction of slope. The overlaps shall be of minimum 100mm on longitudinal directions and 150mm on the transverse direction. All overlaps shall be bonded with bitumen primer and levelled by heating the overlaps with brutane torch. This treatment shall be done by the approved authorised applicators. Guarntee of treatment shall be 10 years complete all as specified and directed by Engr-in-Charge.

(ii) Independent testing of membrane for the approved technical parameters specified herinafter shall be carried ourt from the approved laboritries any other Govt approved laboratory having facilities for the testing membrane. APP membrane shall have following parameteres:- (i) Tear strength :- Longitudnal direction-300N, Transverse direction-250N (ii) Joint Strength :- Longitudnal direction- 650N, Transverse direction-450N

Supply only liquid water proofing compund only complete all as specified and directed by Engr-in-Charge.

M & L for PCC 1:2:4 type B1 (20 mm graded aggregate) as in levelling course over RCC roof surfaces all as specified and directed by Engr-in-Charge.

M&L PCC 1:2:4 type B0 (using 12.5mm graded aggregate) roof kerbs, benching rounded or chamfered on edge including rounded or chamfered edges with necessary form work etc complete all as specified and as directed by Engr-in-Charge.

M&L 10mm thick screed bed in cement mortar (1:6) for laying of tiles/app membrance all as directed and as specified and directed by Engr-in-Charge.

Demolition of brick or stone boulder masnory, built in cement mortar including all quoins, arches, pillars, etc., but excluding ashlar facing, dressed stonework and percast concrete articles complete all as specified and directed by Engr-in-Charge.

M&L for Brick work with subclass B bricks, staright or curved on plan exc 6.00 mtr mean redius, biult in 1:6 cement mortar complete all as specified and directed by Engr-in-Charge.

M&L for brick work with subclass B bricks, staright or curved on plan on plan to any redius in half brick thickness wall, biult in 1:4 cement mortar complete all as specified and directed by Engr-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) removing serviceable tiles to store and rubbish off the premises complete all as specified and as directed by Engr-in-Charge.

M&L for colour glazed ceramic tiles in vertical surface 300 x 600 x 7-8mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over 15 mm thick rendering in cement mortar 1:4 complete all as specified and directed by Engr-in-Charge.

M&L non skid ceramic coloured printed tiles 7 to 8 mm thick (square/rectangular) area of each tiles exc 0.11 sqm but n. exc 0.18 sqm, in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match over 15 mm thick screed bed or bedding layer in cm (1:4) complete all as specified and directed by Engr-in-Charge.

M&L for PCC 1:2:4 type B-1(20mm graded aggregate),25mm thick as in sub base to the tile flooring complete all as specified and directed by Engr-in-Charge.

Demolition of plain cement concrete (unreinforced) of any description and any position not otherwise provided complete all as specified and directed by Engineer-in-Charge

M&L cement concrete 1:2:4 type B1(using 20mm graded stone aggregate) as in coping and cover slab,culvert incl form work, bed plates, benching, blocks etc complete all as specified and directed by Engr-in-Charge.

M&L gunniting work to RCC work in col beams chajjas balcony slabs, landings, railings,parapets, projection etc by removing loose, concrete, cleaning of surfaces with wire brush and applying one coat of apoxy paint to rusted reinforcement with and incl welded wiremesh fabric or or wirenet of size not less than 95x95x 3mm, adhesive plaster grade for concrete admixture and providing gunniting pressure 2.5 Kg/sqm with admixture of one part of cement and 3.5 part of sand with thickness of 30mm average complete incl and making the surface even & smooth incl 5mm thick plaster in CM 1;3 ,complete all necessary form work and complete all as specified and directed by Engr-in-Charge incl preparation of newly plastered surface and applying two coats of exterior emulsion paint or two coat of Oil bound distemper as directed by Engr -in - Charge

All as per item above but 24 mm thick for ceiling including preparation of newly plastered surface and applying three coats of white wash as directed by Engr -in-Charge

M&L for preparation of new plastered surface of walls and applying two coats of exterior emulsion paint over two coat of wall care elastomeric putty on wall to achieve smooth surface all as specified and as directed by Engr-in-Charge.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for manholes etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in any type of soil all as specified and directed by Engr-in-Charge.

All as per item No 27 above but Hard rock complete all as specified and as directed by Engr-in-Charge.

M&L 450 mm dia reinforced concrete pipes class NP2 laid and jointed complete with collars including taking down old ones incl necessary earth work and retrunin filling and removal complete all as specified and as directed by Engr-in-Charge.

M&L for PCC 1:4:8 tpe D2 (using 40 mm graded Stone aggregate ) as in foundation complete all as specified and as directed by Engr-in-Charge.

M&L PCC 1:2:4 type B2 (using 40 mm graded aggregate) as in surface channel and drains complete all as specified and directed by Engr-in-Charge.

M&L for mild steel framed work such as grills, gratings, etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks, drain Covering and similar work conforming to Fe 410-0 or Fe 310-0 complete all as specified and as directed by Engr-in-Charge.

Returning, filling in , including spreading, watering and well ramming in layers n.exc 25 cm thick using soils all as specified and directed by Engr-in-Charge.

Removal of excavated material for a distance exc 5KM but n.exc 10KM and depositing outside the defence premises on desecration of Contractor as directed by Engineer- in -charge.

S&F precast machine pressed PCC interlocking paver block of 60 mm thickness, M-40 grade of any colour & design with grey cement and pigment as approved complete all as specified and directed by Engineer-in-Charge.

M&L for sand filling under floor or in foundation including watering & consolidation complete all as specified and directed by Engineer-in-Charge.

S&F Colour coated galvalume aluminum zinc coating GI based corrugated/ style pattern steel sheet 0.50mm thick fixed to steel frame using L or J bots with washer in roofs including making good joint frame and sheets, complete all as specified and directed by Engr-in-charge.

S&F steel/work in tubular truses, purlins, rafters, struts, vertical members and similar work including special shape washers complete using ERW or induction butt welded tubes confirming to I.S. 1161-1998 grade St-240 complete all as specified and as directed by Engr -in - Charge.

M&L for excavation in post holes ( or similar holes) in any type of soil each n.exc. 0.5 cum, getting out returning filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm complete all as directed by engr in charge

M&L for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in plinth protection including making joints and filling with sand bitumen mastic complete all as specified and directed by Engineer-in-Charge

M&L for aluminium powder coated of coloured frame and other accessories suitable section as in fixed partition, door and as required , glazing aluminium clips, Aluminium bracing and other fixing aluminium section all as specificed and directed by Engr-in-Charge.

S & F for powder coated aluminum as in door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified and directed by Engineer-in-Charge

S & F for aluminum power coated any colour (minimum thickness of power coating 50 micron) as in window and ventilator shutters side hang type, aluminium section weighing 0.55 kg/m incliding necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1No) hinges type B-21 100mm long (2 Nos) suitable handle (1 No) 75mm brass tower bolts fixed to shutters etc complete all as specified etc. complete all as specified and directed by Engineer-in-Charge

S & F aluminium deco grills conforming to DG-104 grade all as specified and directed by Engineer-in-Charge.

S & F prelaminated particle board 9mm thick, exterior grade, prelaminated both side with decorative choice laminations fixed with aluminium glazing clips as in door shutter/partitions etc complete all as specified and directed by Engineer-in-Charge.

S&F brass body mortice lock vertical type size 100mm 4 lever, including escutcheon plate and two No keys fixed complete all as specified and directed by Engr-in-Charge. Make : Godrej/Harison

S& F Aluminium (extruded section body) Door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed complete all as specified and directed by Engineer-in-Charge

Taking down frame or Chowkhats (w/o taking off shutter from the frame ) of any description not exc. 1.50 Sqm each incl necessary repair to opening with CM 1:4complete all as specified and as directed by Engineer-in-Charge.

M & L for collapsible steel gates, consisting of channel pickets, pivoted flat bars, top and bottom runners, brass handles etc: as specified erected in position and securing runners with holdfasts and brackets complete all as specified and directed by Engineer-in-Charge

M & L for preparation of untreated new steel surfaces exc. 10cm width or girth of any description and applying two coats of synthetic enamel paint over and including one coat of red oxide zinc primer complete all as specified and directed by Engineer-in-Charge.

Cutting holes into or through brick walls built in cement mortar or cement lime mortar & stone walls built in lime mortar & stone walls built in lime mortar and making good in CM(1:3) or PCC (1:2:4) type B-1 as required Superfacial area not exc 150 SqCM complete all as specified and directed by Engineer-in-Charge

Taking down Chowkhats or frames with shutters without taking off shutters from frames exceeding 1.50 Sqm but n.exc 4.00 Sqm complete all as specified and directed by Engineer-in-Charge

SF in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) including connection to drain (or outgoing pipe) and to flushing pipe, antisyphonage pipe, Plastic water closet seat, black/ white , closed pattern with flat bottom, and cover and mild steel chromium plated or aluminised hinging device etc.. complete all as specified and directed by Engineer-in-Charge

S&F in repairs10 ltr capacity PVC flushing cistern coloured with accessories Flush pipe of polyethylene of low or high density or PVC. 32 mm dia, for low level cistern complete ISI marked all as specified and directed by Engineer-in-Charge

S&F in repairs Vitreous China wash basin 450mm x 300mm, white, flat back, excluding ditto but including 100mm P or S trap, brackets , including cutting for and pinning in ends of brackets or erecting stand including fixing of supply and waste pipe complete all as specified and directed by Engineer-in-Charge

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm all as specified and directed by Engineer-in-Charge

S & F repair CP towel ring all as specified and directed by Engineer-in-Charge

S & F repair CP Soap dish all as specified and directed by Engineer-in-Charge

S & F repair CP paper holder all as specified and directed by Engineer-in-Charge

S & F in repair hand shower( health faucet ) with 1.0 m long easy flex tube in chrome finish and wall hook complete all as specified and directed by Engineer-in-Charge

S&F in repair 15mm CP bib taps fency type chromium plated, with crutch or butterfly handle scrwed down, scrwed for iron pipe or for brass ferrule complete all as specified and directed by Engineer-in-Charge

S&F in repairs 15 mm angle valve chromium plated and fancy type with crutch or butter fly handle with CP wall flange of same make, high pressure screwed down all as specified and directed by Engineer-in-Charge

Taking down steel tubing and connections 15mm bore complete all as specified and directed by Engineer-in-Charge

S&F 15mm bore Tubes, 'medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors complete all as specified and directed by Engineer-in-Charge

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and as directed by Engr-In-Charge.

S&F PVC (SWR) pipes 110 mm single socketed, in any length with solvent cement joints fixed to walls/laid in floors incl stack clamps of stainless steel with bolts & nuts etc.complete all as specified and as directed by Engr-In-Charge.

S&F PVC (SWR) pipes 75 mm single socketed, in any length with solvent cement joints fixed to walls/laid in floors incl stack clamps of stainless steel with bolts & nuts etc.complete all as specified and as directed by Engr-In-Charge.

S&F PVC SWR floor trap with grating including jointing with solvent cement 75 mm dia.complete all as specified and as directed by Engr-In-Charge.

Surface excavation not exc 30cm deep but averaging 15cm deep and getting out sHard/dense soil complete all as specified and directed by Engr-in-charge.

Removing excavated material rock n.exe 50 m and depositing where directed at a level n.exe 1.5 M above the starting point complete all as specified and directed by Engr-in-charge.

M&L providing 100mm thick PCC 1:4:8 type D2, using 40mm graded aggregate as in floors to receive top layer complete all as specified and directed by Engr-in-charge.

M&L for Plate girder or single stanchions, built up of one beam or channel section with flange plates, caps, bases. splices, angle brackets, cleats and other connections confirming Fe 410 -W (Gde- E- 250) quality- A complete all as specified and directed by Engr-in-charge.

M&L 75 mm thick PCC type D-2, (1:4:8) using 40 mm graded stone aggregate as in sub base for floor finishes complete all as specified and directed by Engineer-in-Charge.

M&L for industrial scratch resistant and natural to UV rays outdoor colour tiles of size 300 x 300 x 10mm thick, suitable for vehicular traffic like parking lots driveways, pathways, pavements etc conforming to IS-4457 2007 (Colour terracotta/ivory/gray) (shape-star/Chex/Coin/Plain/capsule/stripe and dot) shape, size and pattern/colour as directed by engineer-in-charge, as set and jointed in neat cement slurry and pointed to coloured cement to match, over 15mm thick screed bed of CM (1:6) complete all as specified and directed by Engineer-in-Charge.

S&F 2mm dia galvanised steel wire ,50x25mm mesh ,made up into mattresses or cages lapped ,wired and laid in position , complete as in chain link fencing all as specified and as directed by the Engineer- in - charge .

S&F factory made 18mm(+0.7mm) thik celuka PVC Ply of density 600kg/cbm manufactured by an ISO-900-2008 certified company.One side prelam and other side plain 18mm thick Celuka PVC ply for kitchen cabinet shutter and also manufacturer's test report and test certificate is mandatory with each and every supply of the materail complete as per directions of Engineer-in-charge,manufecturer's specifications and drawing

S&F factory made 18mm(+0.7mm) thick celuka PVC Ply of density 600kg/cbm manufactured by an ISO-900-2008 certified company.Plain 18mm thick Celuka PVC Ply for Shelf/Partitions/Drawer and also manufacturer's test report and test certificate is mandatory with each and every supply of the materail complete as per directions of Engineer-in-charge,manufecturer's specifications and drawing.

S&F factory made 5mm thick PVC sheet of density 600kg/cbm manufactured by an ISO-900-2008 certified company.Plain 5mm thick PVC sheet paneling for back side(wall side) and also manufacturer's test report and test certificate is mandatory with each and every supply of the materail complete as per directions of Engineer-in-charge,manufecturer's specifications and drawing.

M &L for magnetic catches with brass body and striking plate including letting in and fixed all as specified and as directed by the Engineer- in - charge .

S&F stainless steel knobs complete all as specified and as directed and specified by Engineer-in-Charge.

S&F for 125 mm size of hasp & staple safety type Stainless Steel with mild steel hinge pin including bolt to heinge plate and fixed with screws complete all as specified and directed at site.

S&F Continuous piano type hinges stainless steel 30 mm flap size complete all as specified and as directed by the Engineer- in - charge .

Cutting openings through walls built in cement mortar for door, window and other openings or enlarging existing openings, and making good etc., or cutting out defective masonry for underpinning including providing, fixing and removing, shoring, cleaning and stacking stone and removing surplus to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge.

AASHIANA CONSTRUCTION COMPANY