Shifting of existing street light poles along with LED Fittings located within TMC, plot, obstructing the construction of compound wall of ICTREC campus in survey No. 1A/1/A, Tambati village, Raigad.

Amount

Excavating trenches of required width for pipes, cables, etc. including excavation for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, dewatering etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : reinstatement of the same after the cable is laid in approved manner ( 750 mm wide),in all types of soils.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth, 1.5m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth, lead up to 50m and lift up to 1.5m,as directed by Engineer-in-Charge., in all types of soils

Providing and laying in position cement concrete of specified grade including curing, finishing etc. including the cost of steel reinforcement, centering and shuttering - All work up to plinth level: 1:2:4 using 20mm max. size aggregate.

Installation and fixing of existing 7 Mtr. hot dip galvanised Octagonal street light pole with existing light the existing pole is of 7 mtr and having hexagonal bracket suitable to mount integral flood light fixture & 1.5M double arm bracket suitable to mount two nos. of street light fixture. Suitable for 47 m/sec wind speed. (Fixtures can be mounted on the hexagonal bracket on six sides of the bracket but at max only 3 no. of integral flood lights can be mounted at a time.).with suitable foundation bolts, bakelite with 2 nos. 6A SP MCB and stud type terminal block/connector box of approved make suitable for terminating cable up to 4Cx16 sqmm size

Removing and shifting of existing 7 mtr street light pole with its existing light fittings , internal wirings to new location ( 100Mtr distance aprox) with required manpower , machinery , tools etc. as per location decided by EIC-ES.

Supply and fixing of 01 No. street light pole arm on existing pole, matching the design and specifications of the existing arm. Including welding, painting etc. required as per instruction of EIC-ES.

Casting of new foundation for 7 Mtr. poles of above type including excavation of pole pit. The concrete mix for RCC foundation of Octagonal pole shall be M 20 including the cost of steel reinforcement, centering and shuttering. The scope shall also include grouting of foundation bolts including curing & provision of DWC HDPE pipe for passage the cable and finishing the surface (Composite).

SITC of LED Street light fixture 90 WATT IP 67 , powder coated pressure die cast aluminum body (System lumen efficacy ≥105 <120 lm/Watt) Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated pressure die cast aluminum body with driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, freq 50/60 hz, Operating temp range -15 deg to 50 deg centigrade, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2 , P. F.≥0.95, IP- 66,IK-10, CRI >80, under voltage and over voltage protection, EMIEMC As per CISPR -15, lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65 mm dia pipe, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K/ 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c connections with 1.5 sq.mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output. LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C).

SITC of GI wire 8 SWG, for pole earthing

Supply, fabrication & installation of MS angle/ Strip/ plate / rod/ channel etc. as per given design duly painted with 2 coats of red oxide & 2 coats of enamel paint of approved shade all as per the instruction of EIC. 20 mm dia 1.5 m long.

Supply, laying, testing & commissioning of 1.1 KV AC grade of 4 core x 16 sq. mm Aluminium Conductor cable conforming to IS: 1554/Part 1/1998, XLPE, 1100 V class PVC insulated ISI mark armored, bright annealed Aluminium conductor cable in ground at 900 mm back filling & re-instatement, consolidation & removal of excess earth within a radius of 500 mtr including clamping , saddling , cable route tag , laying of cable tiles / brick, sand filling throughout underground route. for sports lighting

Supplying and laying (including excavation of suitable width & depth up to 900 mm) 50 mm outside dia. double wall corrugated pipes (DWC) of HDPE for enclosing cable below ground/road surface, complete.

SITC of 16 sq.mm cable gland double compressed

SITC of 16 sq.mm lug aluminium

SITC of 3 x 2.5 sq. mm PVC flexible cable copper for pole junction box to light fitting