ELSD/AJJ/SOUTHERN RLY Tender Results

Brush Paints & varnishes (flat) Size :- 38mm as per IS : 384-2002 & Bristles to 1844-1993 IS-384-79 & Bristles to IS-1844-76 Rev.-2 Type A.

Set of Galvanized hexagonal head bolt fully threaded of grade 8.8

OIL PIPE COMPLETE

CURRENT TRANSFORMER (TFILM) RATING 250/5 AMPS

VALVE COMPLETE AS PER REPL PART NO S1320 OR ANANTASHREE PART NO G1320

Nitrile bonded rubberised cork gasket for Loco transformer conforming IS 4253/Part II - 1980 (Reaffirmed 1999) : Grade : RC 70C very good oil resistance of size ID 683mm plus or minus 2mm, OD:765mm plus or minus 2mm, thickness 6mm with 18 holes of 14mm dia at equally spaced on 720 PCD

set of steel brazed grease pipe with nipple

CU GASKET AS PER ANANTASHREE PART NO : G31.2 OR AS PER REPL PART NO : S31.2

Cover for REPL make SMGR REPL part no. A4150.6/AG-430562-P1

Compression Spring; REPL Pt No A4430.10 ; Drg No. AG-430510-P1

Auto drain valve for WAG9 locos to KBIL Part No. I82281.

CGR WASHER AS PER ANANTASHREE PART NO : G2539 OR AS PER REPL PART NO S2539

Roof Clamping Bolt as per Drawing No. SR. DEE/RS/ED/MISC/20.

Baniyan Waste ( Cotton ) of Various Colours and Sizes of minimum 200 mm on each side.

Supply of L Clamp for VCB, made of Electrolytic Copper (EC Grade), thickness 6 mm, as per drawing enclosed (Annexure-II).

KABA Key air supply isolating cock of pantograph for 3 phase locomotives

Solenoid Coil to AAL Part No. 4300005400/28 for AAL make VCB of WAG9 Locomotives.

Contactor for Head light, Auxiliaries Compressor and GUSP (Pos No. 48.2, 338, 218.2) AND Auxiliary contactor for Contactor Auxalries (Pos No. 52.3, 52.6), type S- 163 as per CLW Specification No. CLW/ES/3/0034 ALT.-C [ABB Document No. HBTB585402 R0821

GREASE LIPLEX T2 OF M/S. BALMER LAWRIE [ GREASE LIPLEX T2 OF M/S. BALMER LAWRIE OR SERVOGEM 2 OF M/S IOCL FOR SERVOMOTOR PISTON PACKING OF PANTOGRAPH]

Four legged steel wire rope sling as per SRDEE/RS/ED/MISC-201, capacity 5 Ton, Each leg Rope DIA 12 MM X 3500 Length with 1 no master round ring AT TOP AND 2 NOS Sub ring at bottom and 4nos of eye hook OF 2 TON capacity with opening of 42MM

Standard Hardware for TM type 6FRA-6068 WAG-9/ WAP-7 Loco, set consist of 87 Nos. As per page 3 of 5 of CLW Specn. No. 4TMS.096.075 Rev.1 Alt.1

Two legged WIRE ROPE SLINGS Having Ring (Size :270mm x 140mm)At top & Eye hook with Thimble on other end. Each leg made out from USHA MARTIN Un- Galvanized Steel wire rope.6/19 const. RHO Lay. Steel core of 12 mm dia. Effective Length from Thimble to Thimble : 1500mm.Total Capacity :2 ton. All end of rope Double ferrule spliced

SET OF ROOF BAR ALONG WITH HARDWARES

SET OF MILD STEEL WEAR PLATE FOR WAP-4 LOCOS

Set of panels consisting of two items as per CLW Specification No. CLW/ES/C-47 (Alt- J) and CLW Drawing No. SK.No.CLW/ES/SK-5/C-47

Set of hardwares as per Annexure , Hex Head FULLY THREADED cadmium coated bolt 8.8 grade or higher with suitable nut [IS 1364/92], Suitable flat washer [IS 5369/75] and Suitable Spring washer [IS 3064/94]

Set of IOH kit for M/s. Knorr Bremse make Compact Triplate Panel (Part No. II86643). set consists of 18 kits as per attached annexure.

Parts of LED for conversion of 110 V DC 4 feet tube light fitting

UIC CONNECTOR FOR WAG-9 MU OPERATION TYPE UICST 13P EOD2 AS PER CLW SPEC. NO.CLW/ES/3/0047 ALT-E OR LATEST IF ANY

Corridor light 2 feet 9 watts +_ 10% LED version of old 110 DC 2 feet tube light

AOH Kit for rotex make 3403 Model Magnet Valve, Kit consists of 9 items as per annexure enclosed.

Wiper blade BOSCH make model no.3397016580-KTS 20CA (500mm/20").

Wire wound Resistor 4.7 ohms 1000W, Size 50 mm outer dia and resistor length 350 mm with suitable fixing clamp silicon coated

Finger Contact Lever for shunting Contactor

Pivot liner vertical half

Set of Rubber kit for oil pump

Supply of Non flammable ozone friendly heavy duty citrus D-Limonene based Cleaner and Degreaser with high flow system

HEX HEAD BOLT M22 X280 MM AS PER IS 1364 (LATEST REV.) AND CLASS 8.8 OF IS 1367 (LATEST REV.) HAVING 5 MM HOLE AT A DISTANCE OF 12 MM FROM BOTTOM OF THE BOLT AS PER RDSO DRG. SKVL 325 AND M22 SLOTTED NUT TO IS 2232 (LATEST REV.) OF CLASS 8.

M-48 kit for air dryer of Trident make

Double Row Angular Contact Ball Bearing 3306A/C3

Tread brake unit (TBU) bogie rubber hose coupling for WAP7/WAG9 locos as per Drg.No:C/ELS/LGD/PN.Eqpt/3/34.

Set of Special Hexagonal head bolts

SET OF GASKET FOR EPC, REVERSER & CTF

Graphite grease grade III Conforming to specification No IS:508:-2022(Material should have minimum six months shelf life)

NYLON TUBE GRAFLON, OD- 06 mm, ID- 04 mm, CLW DRG. NO. 1209-18-406-056; REF. 2 to 6 , ALT - 5

ECO-SOLVENT TYPE VINYL PRINT STICKER

Set of Hexagonal head bolts

Set of lifting polyster sling

Pressure Gauge (Panto) with adopter

PANTO PRESSURE GAUGE