Loading…
Loading…
6,037 results • Best match
CONSTRUCTION OF ART GALLERY IN SC ONI AT PADASAVALI VILLAGE IN ALAND TALUKA.Under KKRDB for the year 2025-26(Work Code KLB257211410)
Steel Fabrication
Construction of New Anganawadi Building at Hosuri of Hadagali village in Vijayapur Taluk (2022-23th Pradhan Mantri Adarsh Gram Scheme)
Steel Fabrication
Reconstruction of bridge
Steel Fabrication
CA NO. GE AF NO.1 / GUR-60 / 2026-27 REPAIR/REPLACEMENT OF LT UG/OH ELECTRIC DISTRIBUTION NETWORK SYSTEM INCL ALLIED WORKS AND EARTHING PITS IN DOMESTIC AREA AT AF STN GURGAON UNDER GE (AF) GURGAON NO.1
Dismantling and taking down old unsv LT Panel and Supply, Install, Test and Commissioning outdoor type cubical panel board of size 1.2 x1.0 x0.5M, outer shell made out of 3.15 mm thick MS sheet and inner shell made out of 2mm thick MS sheet and MS angle section 50x50x6 mm mounted on PCC 1:2:4 type B-1 platfrom 60 cm below the ground level, frame factory fabricated with front and back openable double door system and cable alley ( Each door hinged with body at 3 places with body and hinges should be welded with body and door) lockable/openable with arrangement of pad locking on both doors incl 2 No of pad locks of three keys shall be used to make the outer shall completely vermin proof suitable for 3 phase 4 wire 415 volt, 50 Hz, incl Aluminium bus bar 3 phase (RYB) of 400 A and 1 phase ( Neutral) 200 Amp, tested at factory approved from CPRI factory fabricated having modern fabrication and testing process followed by powder coat 7 stage painting having thickness not less than 100 microns provided with suitable gasket to make it dust/vermin proof and general construction conforming to IS 8623/93 comprising of the following :-
CONSTRUCTION OF SCADA BUILDING AT SECTOR-20B, FARIDABAD
171 Providing and fixing roller blinds comprising of polymer coated fibre fabric with minimum openness factor of 3% as per AS standards. The fabric shall be fire retardant and have high heat reflection ratios. The roller mechanism shall be a moulded unit made from engineering grade plastic polymer with steel spring support. The fabric shall be finished on the sides with edge tape duly welded for waviness control. The fabric shall be attached to the roller tube with high quality self adhesive tape. Average width of blinds shall be 2000mm and fall of 3000mm with manual operation. Headrail: shall be .812` high x 2` deep extruded aluminum headrail with a wall thickness of 0.045” and painted to coordinate with fabric color. Cord lock: shall be a snap-in design of injection-molded thermoplastic incorporating a metal, free-floating, serrated cord-locking roller. Lift cord: shall be 1.2mm polyester and concealed for a clean appearance. A snap tassel and joiner ball connect to a single Danskord for raising and lowering the shade. Cord, tassel and joiner ball are color coordinated with fabric. Installation: Bracket shall be low profile, hidden snap-in design made of 0.025” zinc-plated spring steel. Bottomrail: shall be 0.375` high x 2` deep extruded aluminum with a wall thickness of 0.045” and painted to coordinate with fabric color. Fabrication Shades shall be fabricated according to specifications and accurate to tolerance established by SWF engineering standardS 300 Sqm 0 Excess(+) Full Conversion INR
Electrical work related to:- (i) Proposed Project store at BCY (ii) Setting up of Mechanized laundry capacity 1.5 at Mau & capacity augmentation of Mechanized laundry at BSBS & CPR of Varanasi division (iii)Provision of Train passing office building at Various stations of Varanasi division
Description:- Supply, fabrication, and erection of fabricated structure angle iron 35x35x5mm