Loading
Loading…
Loading…
6,248 results • Best match
Construction of RCC Culverts at P & T New Colony Road No.1 Plot No.9 & 10 in 10th Division. 9th Call General Funds
VRCC M-20 mix using 20mm ansize graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggrregate (sand) coarse aggregate, water etc., to site and including seigniorage charges, sales & other taxes on all labour charges such as machine mixing, laying concrete, curing etc., complete but excluding cost of steel and its fabrication charges for finished item of work (with centring charges)
INCREASING CAPACITY OF 132/33KV SUBSTATION DLW VARANASI AND ALL ASSOCIATED WORK
Grouting of 04 No. 65X65X6 mm G.I./ M.S. Angle posts of size 3000 mm after due fabrication with C.C. mixture in the ratio of 1:2:4 Fixing & welding of open hut type G.I./M.S. angle. Angle frame structure of size 3000X2400X2400 mm by due fabrication with 65X65X6 mm size & 50X50X5 mm size G.I./M.S. angles on above grouted G.I./ M.S. Angle posts by due cutting drilling welding etc. of G.I./M.S. Angles to be provided by department for each fire Hut.
This work is intended for Setting up of Dialysis Units in Major Hospital Providing Additional EI for the Dialysis Block at Taluk hospital Njarakkal, Ernakulam.Electrification General Electrical Work
90.14.1.2:Fabrication, supply, conveyance, installation testing and commissioning of floor or wall mounting, dust and vermin proof, cubicle type MV panel board comprising of the following components/ devices & complying to IS 8623. Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments will be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc.Supply and fabrication of MV panel board using 1.6mm CRCA sheet, powder coated (excluding base frame)
Construction of Shed for new twin tempering furnace at the New Axle Forge Complex. (Grid O'Q' 35A to O'Q' 43) inside factory premises of RWF.
Fabrication of side post for installing on existing steel structure/RCC structure- 6 Breaking Strength : 10 KN. Length:350mm to 550mm.Installation Type : To be welded on existing Steel Structure, for fixing on RCC structure, MS Plate 10mm thick shall be provided over existing RCC Structure and to be fixed with Anchoring bolts. Side post shall be welded over the MS plate.
JJM-5th SWSM- WSS to Mylapra,Malayalappuzha and Vadasserikkara Panchayaths-Construction of 6LL OHSR at Cheenkalthadam.
100.37.11.2:Fabricating M.S. flanges of diameter 400mm using 12mm thick M.S. plate including cost and conveyance charges of M.S. plate, all fabrication charges, charges of painting the steel work with two or more coat deluxe multi surface paint to give an even shade over an under-coat of primer etc., complete: For pipes fabricated with 8mm thick M.S. plates.
Improvements to road from (i) SH 33 to Vaderpura Via Srikantaianapalya Bestarapalya and Colony (Road ID-688), (ii) Bychenahalli to Gubbi Border Via Bisalahalli, Chikkagollahalli and Kaduvinakunte (Road ID-2929), (iii) Shanthapura to Bannikuppe Cross Via Chikkanahatti (Road ID-3028) in Tumakuru PIU - ADB FINANCED
Steel Fabrication Supplying, fitting and placing TMT FE 550 / 550D Steel Reinforcement including cost of all materials, machinery, labour, cleaning, straightening, cutting, bending, hooking, laping/we...