Loading
Loading…
Loading…
1,334 results • Best match
PROVISION OF DEFICIENT WORKSHOPS AND ALLIED FACILITIES AT NAD, VISAKHAPATNAM
Supply and fixing LED Solar street light fitting 20 Watt including galvanized steel pole in built, lithium ion battery, solar panel, charge controller with dusk down sensor complete all as specified.
RETROFITTING TO PWSS VILLAGE RULE TAL.VELHA DIST PUNE UNDER JJM 21-22 Open Class
SUBWORK NO.10 SOLAR Item No.1 The design, Manufacture supply Installation, Commissioning and Testing of Solar photovoltaic water pumping system 10 H.P.D.C. submercible Pump- as per MNRE Specifications- Specifications of Solar Deep well (submersible) Pumping Systems with D.C. Motor Pump Set with Brushes or Brushless D.C. (B.L.D.C.) Technical Specification- 10 H.P. Submersible pump for Water Supply Well / Borewell . B.L.D.C. (Min.9000 Wp PV Array). (1) Discharge 207000 litres per day from a total dynamic head of 50m. and Shut off dynamic head 70m or (2) Discharge 135000 litres per day from a total dynamic head of 50m. and Shut off dynamic head 100m or (3) Discharge 94500 litres per day from a total dynamic head of 70m. and Shut off dynamic head 150m PV Array should be as per IEC 61215 Specifications and qualify IEC 61730 part 1&2 testings , 4 sq.mm - 3 core flat ISI mark copper cable, On off switch, dry run and lightening protection, Scope of work- supply, Installation, commissioning , Testing, third party inspection, Transportation , Insurance for 5 years, 5 years warrantee, 5 years repairs and maintenance, Remote monitoring System and applicable taxes. Necessary certificates, operation and maintenance manual etc. (As Per GOI MNRE Letter No.32/24/2020-SPV Division Dated 18/08/2021)
Sewerage and Septage Management for sewer system with STP and laying, jointing, testing and commissioning of Sewerage System in two (02) ULBs of Cluster-4 including 1 year defect liability with 10 years O and M.
Supply, installation, testing and commissioning of MNIE approved off Grid Solar Panels for running of motor pumps with 25 years of Linear Generation warranty, Work includes designing of solar panel area and MS fabricated structure 120 micron hot dip galvanized iron, showing arrangement of panel In available space and installation of PV module on frame structure such that minimum height of lower edge of panel shall be 4.0 mtr from ground level to safeguard against damage and theft as per indicative drawing enclosed with the bid document. The foundation of structure shall be in ACC Mounting structure shall be suitably designed to withstand wind velocity up to 150km/hr. The work shall be executed as per detailed technical specfications, approved drawing and direction of Enginees in-charge. Note There shall be 5 year service warranty for solar panel and mounting structure and suitable provision shall be included in tender document.
Estimate for construction of bridge at RD 75000 of Ibbon Minor.
Providing and installation of solar cateye produced from an engineered polymer selected for superior impact resistance and weather-ability. The top of the solar stud should be transparent for solar charging and light output in active mode. The base of the body shall be yellow or neutral white as approved by Engineer In-charge. The marker shall incorporate a solar panel (comprising of solar cells) for converting solar energy into electricity, a storage device for storing the energy, LEDs for illumination and a design for providing 360 degree smooth illumination. The Solar stud shall be round in shape for providing illumination in all directions. The solar stud shall also have high reflective lenses for conspicuity in passive mode and dual shanks for improved road presence. The solar studs are intended for application directly onto pavement surfaces and shall be applied with epoxy resin adhesives designed for use with raised pavement markers and as supplied by the marker manufacturer separately. The solar cateye shall be of height: 65 ± 2 mm & Maximum Diameter: 136 ± 4 mm. The body of the solar cateye shall be resistant to dust and water ingress as per IP 65 standards. The marker shall support a load of 13635 Kg tested in accordance with ASTM D4280.
Estimate for construction of bridge at RD 74300 of Ibbon Minor.
Providing and installation of solar cateye produced from an engineered polymer selected for superior impact resistance and weather-ability. The top of the solar stud should be transparent for solar charging and light output in active mode. The base of the body shall be yellow or neutral white as approved by Engineer In-charge. The marker shall incorporate a solar panel (comprising of solar cells) for converting solar energy into electricity, a storage device for storing the energy, LEDs for illumination and a design for providing 360 degree smooth illumination. The Solar stud shall be round in shape for providing illumination in all directions. The solar stud shall also have high reflective lenses for conspicuity in passive mode and dual shanks for improved road presence. The solar studs are intended for application directly onto pavement surfaces and shall be applied with epoxy resin adhesives designed for use with raised pavement markers and as supplied by the marker manufacturer separately. The solar cateye shall be of height: 65 ± 2 mm & Maximum Diameter: 136 ± 4 mm. The body of the solar cateye shall be resistant to dust and water ingress as per IP 65 standards. The marker shall support a load of 13635 Kg tested in accordance with ASTM D4280.
Construction of fall at RD 75500 of Ibbon minor.
Providing and installation of solar cateye produced from an engineered polymer selected for superior impact resistance and weather-ability. The top of the solar stud should be transparent for solar charging and light output in active mode. The base of the body shall be yellow or neutral white as approved by Engineer In-charge. The marker shall incorporate a solar panel (comprising of solar cells) for converting solar energy into electricity, a storage device for storing the energy, LEDs for illumination and a design for providing 360 degree smooth illumination. The Solar stud shall be round in shape for providing illumination in all directions. The solar stud shall also have high reflective lenses for conspicuity in passive mode and dual shanks for improved road presence. The solar studs are intended for application directly onto pavement surfaces and shall be applied with epoxy resin adhesives designed for use with raised pavement markers and as supplied by the marker manufacturer separately. The solar cateye shall be of height: 65 ± 2 mm & Maximum Diameter: 136 ± 4 mm. The body of the solar cateye shall be resistant to dust and water ingress as per IP 65 standards. The marker shall support a load of 13635 Kg tested in accordance with ASTM D4280.