Street Lighting Tenders

S/E of 45 watt Led street light fitting ( Phillips, Bajaj, Crompton, Wipro, G.E Or Havells) make i/c all patty material required to complete the job in all respect

S/E of 45 watt Led street light fitting ( Phillips, Bajaj, Crompton, Wipro, G.E Or Havells) make i/c all patty material required to complete the job in all respect

Comprehensive maintenance of LED Solar Street light fitting of any make any model fitted on the pole at any height with any type of fixing arrangement by checking all connections, replacing the drivers/ Controller, surge protection device, control wiring copper wire and lugs, battery, solar PV modules all as directed by Engineer in charge. Comprehensive maintenanace also includes taking down street light fitting of any capacity from any height from the pole and increase or decrease the height of the fixing arrangement by removing the bent pipe and clamps and refixing it to the proper height and removing all the hanging wires, cables, PVC pipes, old rusted clamps, hanging aluminium wires, hanging grasses etc and tightening of all nuts, bolts, clamps and fixing of the street light at proper direction to the satisfaction of Engineer in charge) Spares under Comprehensive Maint should be measured and paid seperately complete all as specified and directed.

LED Street light fixture, powder coated pressure die cast aluminum body (System lumen efficacy ≥135 lm/Watt) Supplying, installation, Testing & Commissioning of Street light LED fixture, powder coated pressure die cast aluminum body with built in or separate driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, freq 50/60 hz, Operating temp range -5 deg centigrade to 50 deg centigrade, internal surge protection of 5 KV L,N,E as per IEC 61000-45, Driver efficiency >85%,THD 10% as per IEC 61000-3-2 , P. F.≥0.95, IP66,IK-10, CRI ≥70 , under voltage and over voltage protection,EMI-EMC as per CISPR-15, lenses for beam angle as per IESNA type I/II/III as per the width of the road and the project requirement., suitable to fit in up to 65mm dia pipe, life time (LED,Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends as per LM80 extrapolation IES TM-21-11 report , CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin) , SDCM(Standard Deviation Color Matching) 5, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥135 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). 45 watt

62 70 watt LED light fitting with all accessoies (for street light), including making connection to street light wire and showing glow i. 70 watt LED lumanary - 1 No. ii. G.I pipe bracket (for street ligth) - 1 No. iii. Clamp with Nut & Bolt (Suitable for G.I pipe bracket and ST pole SP-21/SP-10) - 2 No. iv. PVC copper cable single core 2.5 Sq.mm - 6 Meter No. 1

S & Fin replacement street light timer switch 1-32A, 230 Volts encluding control panel internal wiring and terminals as per existing make in street lights timer panel all etc complete as specified and directed by Engr-in-charge. Make : Selec/Havells or its equivalent