Vehicles, Auto Parts & Repair Tenders

Supply, Erection & Commissioning of fully automatic Star Delta Starter of cap. 150 Amp Including all accessories as one incomer of MCCB (150Amp) with 1 No MCB for lighting load, Contactor rating 120 Amp, 90 Amp, 70 Amp with control transformer for control supply, outgoing indicator, having MPR & all types of protections i.e.UV/OV/ over current, phase imbalance/phase reversal protection, locked rotor, dry run etc, Digital meters, Push buttons, bus bars, capacitor bank, seperate relay for single Phase protection etc. complete in all respect suitable for open fields operation of 1 No. Motor of capacity of 30 HP with a stand of MS channel with canopy having suitable operating height above the kachha open fields as per approved specifications of the department. (suitable for voltage range 380 +- 10%,) panel should be outdoor type.

Supply, Erection & Commissioning of fully automatic Star Delta Starter of cap. 150 Amp Including all accessories as one incomer of MCCB (150Amp) with 1 No MCB for lighting load, Contactor rating 120 Amp, 90 Amp, 70 Amp with control transformer for control supply, outgoing indicator, having MPR & all types of protections i.e.UV/OV/ over current, phase imbalance/phase reversal protection, locked rotor, dry run etc, Digital meters, Push buttons, bus bars, capacitor bank, seperate relay for single Phase protection etc. complete in all respect suitable for open fields operation of 1 No. Motor of capacity of 30 HP with a stand of MS channel with canopy having suitable operating height above the kachha open fields as per approved specifications of the department. (suitable for voltage range 380 +- 10%,) panel should be outdoor type.

Suitable for handling saline and silty water with rpm 960 (Sync) or less. The material of construction of flange, suction bell, bowl, shroud shall be CI with 2% Nickel. Impeller, Shaft, shaft sleeve, fastener shall be of SS 304. Suction pipe and Delivery pipe should be in SS 304 with minimum thickness 6 mmand of suitable length (varies from 4-10m) or as per site condition. The prime mover of the pump is to be 3 phase TEFC squirrel cage induction motor of reputed make having star rating above4 operating at 415V +/- 10%, 50 Hz +/- 5% connection with F class insulation, control panel must have dust and vermin proof vertical mounted cubical type panel board of reputed make with FCMA soft starterofreputed make, MCCB including phase failure protection, surge protection device, dry run protection, overload over current protection, thermal overload protection relay, earth fault relay, voltmeter-ammeter fault indication, start and stop switches and power factor correction capacitor etc. Wiring and earthing should be as per regulations of KSEB and electrical inspectorate. Separate cubical type energy meter panel with CT metering provision including 4 Pole FN type isolator, RCCB , HRC fuses and carrier. Suitable size Copper cable for connection from electric post to meter box and meter panel to motor control panel etc. should be fitted at site, with proper earthing. Cable termination should be as per the regulations and specifications of KSEB and Electrical Inspectorate standards. Screen with 6mm GI welded mesh with 50 mm x 50 mm opening size (about 20 sq.m area) framed in GI angles and GI tubes fitted at the opening on top and sides of sump to prevent entry of unwanted materials to the pump through inflow water. Proper I-section should be provided for supporting the motor mountings and pedestal. Suitable chain block and tripod facilities to be provided for lifting the motor at least 1.00 m above maximum flood level. Rate quoted should be inclusive of all the charges for supply, installation including trial run and commissioning, all types of transportation and conveyance, loading and unloading charges, charges for factory testing, but excluding GST etc.

Supply and Delivery Of Light Commercial Vehicle of Following Specifications: 1.Displacement (CC) / Engine Capacity-700 CC- 1250 CC , 2. Max Power 20-30BHP2500 Rpm And Above, 3.Max Torque- 50ONM @ 2000 Rpm And Above, 4.Type Of Fuel-Diesel. 5. Load Capacity -2 Cu.Rn, 6. Vehicle Emission Norms- BS-VI, 7.No Of Cylinder In Engine 2-4 Cylinder, 8.Length Of Chassis- 3800 Mm 3950 Mm, 9.Width Of Chassis-1500 Mm - 1550 Mm. Ground Clearance. 150 Mm -165mm. 10.Fuel Tank Capacity-Diesel-30 Ltrs To 40 Ltrscng-12-25kg. 11.Size Of Tyre's & No's-145 R 12 - 5 Nos. 12.Wheel Base- 1900 Mm- 2250 Mm. 13.Gross Vehicle Weight- 1550 Kg-1900 Kg. 14.Clutch- Single Plate Dry Friction Diaphragm. 15.Transmission System-Manual. 16.No Of Speed/ Forward Gears- 4 Nos Speeds(4F+1R). 17.Type Of Steering -Manual / Power. 18.Spead Governors -Shall Be Fitted. 19.Pay Load-800Kg To 1000Kg. 20.Tipper Body Length -2100 Mm-2200mm, Mild Steel. 21.Tipper Body Width- 1400 Mm -1500mm, Mild Steel. 22.Tipper Body Height- 750mm-950 Mm, Mild Steel. 23.Side Portion (LH & RH)& Rear Doors Sheet Thickness - 2 Mm, Mild Steel. 24.Tipper Body Top Sheet Including frame Sheet Thickness -1.6mm, Mild Steel. 25.Tipper Body Top Lid Sheet Thickness 1.2mm, Mild Steel. 26.Tipper Container Should Be Fabricated With Two Doors On The Rear Side And Four Doors On Four Top Corners Of The Containers With Hinges And Locking System. A Partition Should Be Provided On The Middle Cf Container Along The Vertical Length Of The Body. 27.Tipper Body Top Lid Main Sheet Thickness- 75 X 40 X6 Mm. 28.Hydraulic Cylinder Make Reputed Make. 29.Hydraulic System Driven-Main Engine. 30.Pump Make-As Per IS Standard. 31.Painting-Should Be Painted With One Coat Of Anti-Corrosive Epoxy Primer And Two Coats Of Enamel Paint For Approved Quality To Ensure Long Lasting Resistance For Weatherizing And Breakage. The Color Shade Should Be As Per Norms. 32Lettering -To Be Carried Out As Directed By Dept Officer. 33 Tipper Body Rear Door-Shall Be With Necessary Locking Facility. 34.Side Safety Guard- Shall Be Provided As Per RTO Requirernent. 35.Additional Conditions-Vehicle With Fuel Sensor And GPS Tracking. 36.Warranty Distance/Year -25000KM//12 Months Which Ever Is Earlier. (One Year O&M By Suppliers) including GST.