Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹18.4 CrAccepted-Finance AMLA TOLA CHAIBASA DIST WEST SINGHBHUM JHARKHAND 833201 | CHAIBASA | WEST SINGHBHUM | JHARKHAND | 833201 | ₹18.4 Cr | L1 | Accepted-Finance L1 |
| 2 | L2₹18.9 CrRejected-Finance M 13 S S HARMU HOUSING COLONY RANCHI DORANDA ARGORA RANCHI | ₹18.9 Cr | L2 | Rejected-Finance L2 |
| 3 | Rejected-Technical | - | - | Rejected-Technical NON RESPOSNIVE |
| 4 | Rejected-Technical 4B TOWN SQUARE CHINAR PARK RAJARHAT KOLKATA 700 136 | - | - | Rejected-Technical NON RESPONSIVE |
Tender Value
Refer Docs
EMD Value
₹18.9 L
Closing Date
1 Oct 2024, 5:00 pmClosed
NODAL OFFICER
e-Procurement Cell, Jharkhand State Building Construction Corporation Ltd., Beside Jharkhand Mantralaya, Dhurwa, Ranchi-834004.
Proposed Construction of TRL Building and Professional Courses Building (M.Ed) under Kolhan University, Chaibasa
2024_JSBCC_92788_1
JSBCCL/50/2024-25
Open Tender
Civil Works - Buildings
540 days
Chaibasa
Please refer Tender documents.
4 documents required · 4 mandatory
₹10,000
₹18.9 L
7 Jan 2025
11 Sept 2024
4 Oct 2024
11 Sept 2024
1 Oct 2024
11 Sept 2024
Amount
Earthwork in excavation in foundation trenches in ordinary soil (vide classification of soil item-A) and disposal of excavated earth as obtained to a distance upto 50 M. including all lifts, levelling, ramming the foudation trenches, removing roots of trees, shrubs all complete as per approved design, building specification and direction of E/l.
Extra for earth work in hard soil as per specification and direction of E/I. (vide classfication of soil item B)
Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50Mand lift of 1.5M all complete as per building specification and direction of E/I. (mode of measurement compacted volume)
Earth filling in foundation trenches and plinth in layers not exceeding 150 mm. thick well watered, rammed, fully compacted and fine dressed with earth obtained after cutting within a lead of 50 M. and lift of 1.5 M all complete as per building specification and direction of E/l (Mode of measurement compacted volume).
Providing coarse clean sand in filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including' cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/l (Mode of measurement complacted volume).
Providing designation 75A one brick flat soling joints filled with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/l.
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level - 1:3:6 (1 cement : 3 coarse sand (zone - III): 6 graded stone aggregate 20mm nominal zie)
Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - all work upto plinth level - 1:2:4 (1 cement : 2 coarse sand (zone - III): 4 graded stone aggregate 20mm nominal zie)
Providing designation 75 A brick work in C.M.(1 :6) in foundation & Plinth with approved quality of clean coarse sand of F.M. 2 to2.5 including providing 10 mm thick mortar joints cost of screening materials , scafolding , raking out joints to 15mm depth curing, taxes and royalty all complete as per building specification and direction of E/l.
Providing designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"X4.5"X3") in C.m. (1:6) in super structure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I
Providing designation 112mm thick reinforced designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"X4.5"X3") in C.M. (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening carriage of materials, scaffolding, raking out joints tom 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.
Extra for brick work for EACH consecutive floor above first floor including watering and scafolding, all complete as per direction of E/l.
Second floor
Third floor
Head room/terrace floor
Providing and laying in position specified grade of reinforced cement concrete excluding the cost of centering and shuttering, finishing and reinforcement - all work upto plinth level 1:1.5:3 (1 cement : 1.5 coarse sand (zone - III): 3 graded stone aggregate 20mm nominal zie)
Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and structs etc. above plinth level upto floor five level, excluding cost of centering, shuttering, finishing and reinforcement: 1:1.5:3 (1 cement : 1.5 coarse sand (zone - III) : 3 graded stone aggregate 20mm nominal size)
Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15 degree landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases, above plinth level upto floor five level, excluding the cost of cenetering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand (zone - III): 3 graded stone aggregate 20mm nominal size)
Providing and laying damp-proof course 50mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 20mm nominal size).
Centering and shuttering including strutting, propping etc. and removal of form for
Foundations, footings, bases of columns, etc. for mass concrete
Suspended floors, roofs, landings, balconies and access platform
Lintels, beams, plinth beams, girders, bressumers and cantilevers
Columns, Pillars, Piers, Abutments, Posts and Struts
Stairs, (excluding landings) except spiral-staircases
Providing tor steel reinforcement of 8mm. dia. rods as per approved design and drawing with cutting, bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position (excluding carriage of bars to work site) all complete as per building specification and direction of E/l. TMT FE 500 ( only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd. Bokaro, & Vizag (RINL)
Providing tor steel reinforcement of 10,12,16mm . dia. rods as per approved design and drawing with cutting, bending and binding with annealed wire with cost of wire, removal of rust, placing the rods in position (excluding carriage of bars to work site) all complete as per building specification and direction of E/l. TMT FE 500 ( only valid for Tata (Tiscon), SAIL, JSPL, Electrosteel Steels Ltd. Bokaro, & Vizag (RINL)
10mm dia -
12 to 25mm dia
Supplying, fitting and fixing 35mm thick solid core type non- decorative single leaf flush door shutter with both sides decorative veneered with block board core bended with high quality phenol formal dehydes synthetic resin of standard make with iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I.
Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with both sides non-decorative veneered with block board core bended with high quality phenol formal dehydes synthetic resin of standard make with iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I.
Providing and fixing decorative high pressure laminated sheet of plain/wood grain in gloss/matt suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS:2046 type S including cost of adhesive of approved quality. 1.5mm thick
Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all completeas per building specification and direction of E/I.
Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory windows & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58- 60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modulus of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-In- Charge. (M.S hold fast/lugs or SS dash fasteners shall be paid for separately).
Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid board one side white color and other side of board laminted with PVC foil of minimum 14 micron thickness of approved design pasted with hot melt adhesive for cup boards, work stations and bathroom/kitchen cabinet etc. of required sizes comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/ borer proof, water/moisture proof and fire retardant and fixing with stainless steel piano hinges/soft close clip on concealed hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In- Charge. (Note: stainless steel piano hinges/soft close clip on concealed hinges and necessary S.S screws shall be paid separately) 25mm thick
Providing and fixing 1mm thick M.S. sheet door with frame of 40X40X6mm angle iron and 3mm M.S. gusset plates at the junctions and corners all necessary fittings complete, including applying a priming coat of approved steel primer - using M.S. angles 40X40X6mm for diagonal braces
providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) tramsparent or dyed to required colour or shade with necessary screws etc. complete 125X75X4mm
Providing and fixing aluminium hanging floor door stopper ISI marked anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour and shade with necessary screws etc. complete Twin rubber stopper
Providing and fixing luminium tower bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS 1868) transpoarent or dyed to required colour or shade with necessary screws etc. complete 150X10mm
Providing and fixing aluminium sliding door bolts ISI marked anodised (anodic coating not less than grade AC 10 as per IS 1868) transparent or deyed to required colour or shade with nuts and screws etc. complete 250X16mm
Providing and fixing aluminium extruded section body tubular type universal huydraulic door closer (having brand log with ISI, IS:3564) embossed on the bodyu, door weight upto 36kg. To 80 kg. and door width from 701mm to 1000mm) with double speed adjustement with necessary accessories and screws etc. complete
Providing and fixing bright finished brass 100mm mortice latch and lock ISI marked with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS: 1868) aluminium lever handles of approved quality with necessary screws etc. complete
Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285 fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions i.e. at top, bottom and sides with required EPDM rubber/neoprene gasket etc.. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling C.P. brass / stainless steel screws, all complete as per architetural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately)
For shutters of doors, windows & ventilators including providing and fixing hinges/pivots and making provision for fixing of fittings wherever required inlcluding the cost of EPDM rubber/neoprene gasket required (fittings shall be paid for separately) --- Polyester Powder coated aluminium (minimum thickness of powder coating 50 micron)
Providing and fixing glazing in aluminium door, window, ventilator, shutters and partitions etc, with EPDM rubber/neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge. (cost of aluminium snap beading shall be paid in basic item) With float glass panes of 4mm thickness (weight not less than 10kg/sqm.)
With float glass panes of 8mm thickness (weight not less than 10kg/sqm.).- (Aluminium door).
Providing and fixing double glazed heremeticlly sealed glazing in aluminium windows, ventilators and partition etc. with 6mm thick clear float glass both side having 12mm air gap, including providing EPDM gasket, perforated aluminium spacers, desiccants, sealant (both primary and secondary sealant) etc. as per specifictions, drawings and direction of Engineer-in-charge complete
Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clearestory windows using wire gauge with average width of aperture 1.4mm in both directions with wire of dia. 0.50mm akk complte with 12mm mild steel u beading.
Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2 mm at 100mm. centres and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40x40x6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangements, stoppers, handles, including applying a priming coat of red lead paint, carriage , hoisting and taxes all complete as per building specification and direction of E/l.
Supplying, fitting and fixing M.S. grill made of 20x6mm M.S. flat as per approved design and drawing, properly fabricated with joints continuous fillet welded and finished smooth , carriage of grill to work site, hoisting as per building specification and direction of E/l. (where materials is not supplied by the deptt.)
Providing and fixing fan hook of 16mm dia M.S. bar 1 metre long bent to required size and shape, placed in position and fixed in R.C.C. slab/beam at the time of casting all complete as per building specification and direction of E/l. (where material is not supplied by deptt.)
Providing and fixing stainless steel (grade 304) railing made of Hollow tubes, channels, plates etc,. Including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessry stainless steel nuts and bolts complete i/c fixing the railing with necessary accessories & stainless steel dash fasterners, stainless steel bolts etc. of required size on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge. (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasterners etc,.)
Providing and laying vitrified Paring / Industrial tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 4457:2007, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 300x300 x 10 mm sizes.
Providing and laying Doublecharge Vitrified floor tiles in different sizes (thickness to be specificed by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622/ISO 13006 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including grouting the joints with white cement and matching pigments etc. complete size of tiel 600X600mm
Providing and laying rectified glazed ceramic floor tiles 300x300mm or more (thickness to be specified by manufacturer) of 1st quality conforming to IS:15622 with approved make in all colours,shades,except white, ivory, grey, fume red, brown laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3 Kg/sqm. including pointing the joints with white cement and matching pigments, etc.complete.
Marble stone flooring with 18mm thick marble stone, as per sample of marble approved by Engineer-in-charge, over 20mm (average) thick base of cement mortar 1:4 (1 cement: 4 coarse sand) laid and jointed with grey cement slurry, including rubbing and polishing complete with Udaipur Green Marble
Extra for pre finished nosing to treads of steps of marble stone
Providing and laying 6mm precast white glazed tiles in walls over 12mm cement mortar (1:3) and jointed with grey cement slurry flush pointed with white cement including rubbing, polishing and cost of curing, taxes and royalty all complete as per building specification and direciton of E/l. With "A" grade white 15 x 15 cm tiles.
Chequered precast cement concrete 22mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of the tiles including rubbing and cleaning etc. complete, on 20mm thick bed of cement mortar 1:4 (1 cement : 4 coarse sand) - medium shade pigment using 50% white cement 50% ordinary cement
Extra for flooring work for each consecutive floor above first floor complete as per direction of E/I.
Providing 12mm cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.
Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.
Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l.
Providing 25mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5with 5% cico or any other approved water proofing compoundincluding taxes and royalty all complete as per building specification and direction of E/l. (design plaster)
Extra for plaster work over exterior surface for each consecutive floor above first floor including cost of scaffolding etc, all complete as per direction of E/I.
Second floor
Third floor
Providign and applying Plaster of Paris Putty of 2mm thickness over plastered surface to prepare the surface even and smooth complete.
Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by the rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.
Providing and applying white cement based putty of average thickness 1mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete
Finishing walls with textured exterior paint of required shade : new work (two more more coats applied @ 3.84kg/10sqm) over and including priming coat of exterior primer applied @ 2.20kg/10sqm.
Finishing walls with premium acrylic smooth exterior paint with sillicone additives of requited shade . New work : 2 or more coats applied @1.43 Ltr/10sqm over and including base coat of waterproofing cement paint applied @2.2 Kg/10 sqm
Providing two coats of synthetic enamel paint of approved shade and make over new wooden surface including cleaning the surface after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.
Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.
Providing and fixing false ceiling at all height including of frame work made of special sections power pressd from M.S. sheets and galvanized with zinc coating of 120gms/sqm (both side inclusive) as per IS 277 and consisting of angle cleats of of size 25mm wide X 1.6mm thick with flanges of 27mm and 37mm at 1200mm centre to centre. one flange fixed to the ceiling with dash fastener 12.5mm dia X 50mm long with 6mm dia bolts other flange of cleat fixed to the angle hangers of 25X10X0.50mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate GI channels 45X15X0.90mm running at the spacing of 1200mm centre to centre.
to which the ceiling section 0.5mm thick bottom wedge of 80mm with tapered flanges of 26mm each having lips of 10.5mm at 450mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64mm dia X 230mm long G.I. wire at every junction, including fixing perimeter channels 0.5mm thick 27mm high having flanges of 20mm and 30mm long the perimeter of ceiling gixed to wall/partition with the help of rawl plugs at 450mm centre with 25mm long dry wall screws @ 230mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 X 25mm at 230mm c/c including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes,
finishing with jointing compound in 3 layers covering upto 150mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specirfication and also including the cost of making openings for light fittings, grills, diffusers cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in charge but excluding the cost of painting with:
Fully perforated Gypsum Plaster Board of size 1200X2400X12.5mm having approx 15% perforated area with perforation size and pattern as approved by the Engineer-in-charge and as per manufacturer's specification, with all 4 side tapered and backed by acoustical tissue with NRC value not less than 0.60
Providing & laying water proofing treatment in sunken portion of WCs, bathrooms etc. by applying cement slurry mixed with Armourcrete of M/S The Structural Water Proofing Company PVT. Ltd.or Tapecrete of M/s CICO Engg. Servce consisting of applying :
(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with Armourcrete or Tapecrete @ 0.125 kg/ sq.m. This layer will be allowed to air cure for 4 hours
(b)second layer of slurry of cement @ 0.242 kg/sqm mixed with Armourcrete or Tapecrete @ 0.126 kg/ sq.m. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.
The rate includes preperation of surface, treatment& sealing of all joints, corners, junctions of pipes & masonary with polymer mixed slurry.
Providing 1.5mm cement punning including curring, carriage of water with all leads and lifts as per building specification and direction of E/I.
Providing and laying vitrified Cool Roof tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 154557-2007 / 15013006, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. Its solar reflective index ( SRI ) value should be above 78. complete. Size of Tile 300x300 mm x10 mm thick.
Water proofing for old and new roof slab - Providing and laying water proofing treatment on roof slab by applying two component, factory designed, ready to use acrylic modified flexible material applied with brush roller or spray for water proofing coating as per manufacturer specifications with gollowing steps:
a. Surface preparation - Providing and cleaning of concrete surface to remove dust, oil, grease including removal of existing loose paint/coating and cement laitance by cleaning with compressed air & water jet including all matrials, labour, tools, complete, ponding test to be done after plugging all outlets and to be checked from soffit to identify seepage leakage. On identification of seepage cement grouting to be done with non shrink expanding adminxture of Sika India Pvt Ltd./MYK schomberg/Dr. Fixit/Fosroc or equivalent. Providing and repairing of all corners and joints such as those between the parapet wall and the roof slab etc. sahll be chamfered with 150mm X 150mm fillet of mortar (cement, sand 1:4) admixed with acrylic polymer of Sika/Fosroc/MYK scholmberg/Dr fixit or equivalent. Before chamfering a prime coat shall be given with the slurry of acrylic polymer, Repairing surface irregularities, damaged concretein base slab dead cracks if any, with an acrylic polymer modified repair mortar including a coat of bonding agent of the same with cement slurry including all material, labour, tools complete.
b. 1st coat -Apply 1st coat of two component acrylic modified, ready to use flexible cementitious material on surface saturated dry roof and inside wall of parapet wall upto 600mm by brush or roller. After 1st coat of application, 45 gsm of fibre glass cloth to lay when the first layer is still green. 1st coat should be applied @ 1.50kg/sqmt/coat. Fore the prupose of measurement the entire treated surface will be measured.
c. 2nd coat - To apply the 2nd coat of two component acrylic modified, ready to use flexible cementitious material on right angle to the 1st coat over the glass fibre laid surface 2nd coat should be applied @ 0.7kg/sqmt/coat. For the purpose of measurement the entire treaed surface will be measured After three days of drying the 2nd coat, the rain water outlets to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and if found necessary rectification to be done as per satisfaction of E/C. The water proof coating to be protected from damage before screed over it. Water proofing brand Sika Topseal 109hi/Fosroc Brushbond RFX/Dr Fioxit Pidiffin 2K/MYK Aquafin TG. Product performance- Chemical base part A Acrylic copolymer, Part B Specially graded cementitious powdere density 1.6 kg/I (mixed density) at +27 degree C. Tensile strength - 2N/mm2 after 28 days (with fibre cloth) (according to ASTM D 2370) Pullout bond strength - 2 N/mm2 (concrete failure) (According to ISO 4624) slant-shear bond strength - 4N/mm2 (according to FIP 5.15) Elongation at break - 35% without fibre cloth and 20% with fire cloth (according to ASTM D 2370)
d. Protection of treated surfaces with PCC ; The treated syrface shound be covered with 25mm/50mm PCC of M-20 grade (1:1.5:3) with proper slope (1:120) towards the rain outlets in alternate panels of 2 mt X 2 mtr. Keeping 6mm gap between the panel joint integral water proofing admixture conforming to IS 2645 @ of 100ml per bag of cement to be added in the screed concrete (Paid separately for this items) All corners shall be chamfered with 150mm X 150mm fillet. The rainwater outlets shall be just leveled with the screed concrete to ensure smooth discharge of water - peripherial gaps between PVC pipe outlet and concrete surface should be packed properly with rich concrete nd the peripherial mouth to be sealed with mosture insensitive epoxy putty of sika India Pvt. Ltd/MYK schomberg/Dr. Fixit/Fosroc. For purpose of measurement the entire treated surfaces will be measured e, Grooves of PCC surface should be filled with polysulphide sealant. Brand - Sika India Pvt. Ltd. /MYK Schomberg/Dr. Fixit/Foscroc warranty for five years.
Covering of treated surface with PCC - Providing 25mm thick Cement Concrete M-20 (1:1.5:3) maintaining slope in alternte 2 mt X 2 mt panels with approved quality of stone chips of 20mm to 6mm size graded and cleaned sand of F.M. 2.5 to 3 including screening, shuttering, and mixing cement concrete in mixer with adminxture of integral water proofing and placing in position striking curing, taxes and royalty all complete as per building specificastion and direction of E/I. Panels that has been left should be casted next day. There should be 6mm gap between panels brand - Sika-Plastocrate plus, MYK proof WP 10, Fosroc - Conplast X 421ic, Dr. Fixit pidiproof LW+
Providing and filling 6mm thick groove between 25mm PCC panels with polysulphide sealant (Poring Grade) as per drawings and technical specifications and direction of E/C (with 18%GST) brand - Sika-Polysulphide, Fosroc-Thioflex 600, Dr. Fixit Piddiseal PS (42P) MYK seal PS or equvalent
Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.
Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings (detailed specification as per respective DSR item Sl.NO. a to e and 1 to 6)
Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (detailed specification as per respetive DSR item)
Providing 250 mm wide BRICK DRAIN in cement mortar (1:6) with avarage 150mm. Clear depth and 250 mm apron including cost of earthwork involved with 75m cement concrete (1:4:3) over one brick designation 75A, flat soling in proper grade and slope at the base , the drain dully plastered in C.M.(1:3) with puning over exposed surface all complete as per building specification and direction of E/I.
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
Providing & fixing on wall face unplasticised - Rigid P.V.C. rain water pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 110 mm dia
Providing and fixing on wall face unplaqsticised- PVC moulded fitting/ accessories for unplaqsticised- PVC rain water pipes confirming to IS: 13592 TYPE A,including jointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.
Bend 87.5 degree - 110X110X110mm
Shoe plain -110mm
Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less thaN 440 grams.
Providing and fixing unplasticised PVC pipe clips of approved design to unplasticised PVC rain water pipes by means 50X50X50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 ( 1 cement : 4 coarse sand) and making good the wall etc. complete - 110mm
Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. - 80mm thick C.C. paver block of M-30 grade with approved colour design and pattern.
Providing & injecting chemical emulsion for pre-construction Anti-termite treatment and creating a chemical barrier under and all around the coloum pits,wall treanches,basement excavation, top surface of plinth filling,junctions of wall and floor along the external perimeter of building with approved chemical as per IS code As per specification and direction of E/I.
Carriage of materails
Bricks - Lead - 10km.
Sand - Lead 15km
Chips - Lead 15km
Metal - Lead 15km.
Earth - Lead 2km.
Supplying, fitting and fixing C.I. cover with frame for manhole &ninspection chamber 600X450mm (wt. not less than 25kg) all cost complete as per direction of E/I
Making soak pit 2.5M diameter 3 mtr. deep with 45X45cm dry brick honey comb shaft with brciks of class designation 75 and S.W. drain pipe 100mm diamter 1.8 mtr. long complete as per standard design with FPS bricks
Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25 of size 1000X450X50mm reinforced with 8mm dia four nos longitudinal & 9 nos. cross sectional TMT hoop bars, including providing 50mm dia perforations @ 100 to 125mm c/c. including providing edge binding with M.S. flats of size 50mm X 1.6mm complete all as per direction of E/I.
Supplying, filling, spreading & levelling stone boulders of size range 5cm to 20c, in recharge pit in the required thickness for all leads & lifts all complete as per direction of Engineer-incharge
Supplying, filling spreading & levelling gravels of size range 5mm to 10mm in the recharge pit over the existing layer of boulders in required thickness for all leads and lifts all complete as per direction of E/i.
Supply, assembling, lowering and fixing in vertical position in borewell/recharge pit unplasticized PVC medium well casing (CM) pipe of required dia conforming to IS : 12818 including required hire and labour charges, fittings & accessories etc. all complete for all depths as per direction of Engineer-in-charge 150mm nominal size dia
Costs of drilling 200mmX165mmX125mtr. Deep borewell in all kinds of soil and rock in rural area for installation of pump set with Hydraulic DTH rig machine, all complete including supplying all materials, tools, drilling rig, Air compressor and equipments, as well as fuel lubricants and cost of transportation of rig machine and other vehicles upto the site From 0-50 mtr.
Providing and fixing ball plug/bottom plug of required dia to the bottom of pipe assembly of tubewell/recharge pit as per IS:2800(part 1) 150mm dia
Supplying, fitting and fixing 125mm dia UPVC pipe of approved quality and make - basic rate + 10% for C.P. and laying charge
PLUMBING WORK
Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. (A) With "P" trap (b)12.5 lit. low level P.V.C. cistern
Providing and fixing 8mm dia C.P./S.S. jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer-in-charge
Supplying, fitting and fixing vitreous white glazed earthen ware I.W.C. of parry hindustan or any other ISS approved make with 100mm HCI p trap 15 litres CI pull and let go flushing cistern of names or other ISS equivalent make complete with all fittings CI or C C bracket 32mm alkethene / PVC telescopic flush pipe about 2m long with one brass coupling and clamps GI chain and pull including supplying and fixing a pair of vitreous white glazed earthenware footrest to be fixed in floor 15mm CI body brass spindle stop cock of weight not less than 50 grames 15mm PVC connection pipe 450mm long and coat of red oxide primer etc all complete as per specification and direction of E/I. (A) 580 mm long with 12.5 litre low level PVC cistern
Supplying, fitting and fixing flat back or angular lipped front vitreous white glazed earthern ware urinal of Hindustan "Parry" or any other approved ISS make with 5 ltrs. Capacity C.I. automatic fushing cistern of reliance for any other ISS approved make with all fittings with C.I. or RS brackets standard size G.I. flush pipe with fitting clamps 15mm C.I. body brass spindle stop cock of approved quality weight not less than 400 gms. 15mm PVC alkethene pipe 450mm long with brass coupling at both ends and doing plumber points including painting of exposed part with two coats of approved paint over a priming coat of red oxide cutting wall and floor making good the same etc. all complete as per speciifcification and direction of E/I. Flat back or standing corner (600X350mm)
Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-incharge and finished smooth. - Granite stone of approved shade
supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or hindustan or any other I.S.S approved make supported on painted C.I OR R.S bracket 32mm C.I brass waste 15mm dia C.I body brass spindle stop cock of approved quality of weight not less than 350 grames, 32mm PVC wate pipe 750mm long with brass coupling with one end and making plumber joints etc.all complete as per specification and direction of E/I.
Supplying, fitting and fixing gun metal full way valve of approved quality all complete as per specifcation and direction of E/I.
20mm dia.
25mm dia.
32mm dia
40mm dia
Providing and fixing brass stop cock of approved quality all complete as per specification and direction of E/I. … 15mm dia.
Cutting drain width wise above GL for laying PVC pipe and restoring brick work in cement mortar (1:4) 12mm cement plaster in C.M. (1:4) with neat cement punning as per specifciation and direction of E/I. (PVC 110mm dia)
Making holes in wall for laying PVC pipes and restoring the same all cost complete (PVC pipe 110mm dia)
Supplying all tolls and labour and cutting chajja cornice for laying PVC pipes and making good the same as per specification and direction of E/I. (110mm dia PVC pipe)
Cutting chajjas or concrete for laying PVC Pipe and restoring the same with R.C.C. (1:2:4) brick work in cement Mortar (1:4) and cement plaster 1:4 as per specifiction and direction of E/I
Making holes in walls for PVC Pipe and restoring the same atfer pipe Laying (b) 250mm thick wall
Supplying, fitting and fixing bathroom fittings of approved make and as per IS specification all cost complete as per direction of E/I. (all rates have been adopted from the basic rate from SOR + 30% for labour and Contractors profit)
Pillar cock (long neck)
Bib cock - long thread
Angular stop cock L.T.
4 way diverter for concealed fittings
Glass shelf
Flush valve complete with 32mm size control cock & flange
32mm dia. PVC waste pipe 750mm long with coupling
15mm C.P. nipple with coupling
Steel jali - 14.950mm dia.
Providing Solvent cement
Supplying, fitting and fixing Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror. 600 X 450mm
Supplying, fitting and fixing C.P. brass towel rail 20mm X 600mm with bracket container
Supplying, fitting and fixing C.P. brass soap dish container medium quality with screw and hinges etc.
Providing and fixing Pressure adjustable shower with revolving joint
Providing and fixing 15mm dia and 45cm long PVC connection pipe with heavy quality brass coupling at both ends etc all complete as per specification and direction of engineer in charge
Supplying, materials and labour for constructing inspection chamber of designation class 75B bricks size 750mm deep, 600X450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600X475mm G.I. cover with frame (weight not less than 35kg) alongwith earth work in excavation and 80mm thick PCC (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.
Providing and fixing C.P. brass bib cock of approved quality conforming to IS 8931, 15mm dia nominal bore of approved brand C.P. fittings
Providing and fixing PTMT extension nipple 15mm size with 12" BSP thread 70mm length and 30mm breadth and weighing not less than 18gms of approved make
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i.e fixing the pipe with clamps at 1Mtr. Spacing. This includes jointing of the pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. Concealed work including cutting chases and making good the walls etc.
20mm nominal bore
25mm nominal bore
32mm nominal bore
External work - 40mm nominal bore
Providing & fixing on wall face unplasticised - Rigid P.V.C. pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion . Single socketed pipes. 110 mm dia
Providing and fixing on wall face unplaqsticised- PVC moulded fitting/ accessories for unplaqsticised- PVC rain water pipes confirming to IS: 13592 TYPE A,including jointing with seal ring confirming to IS: 5382 leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.
Single Tee with door 110x110x110 ,mm
Bend 87.5 degree 110 mm bend
Single pushfit coupler
Providing and placing on terrace (at all floor levels) (PVC) Polyethylene water storage tank ISI 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank
Supplying and fixing PVC fittings of approved make confirming to IS : 1729 including supplying nails and bobbins, fixing solutions including earth work or masonary work cutting and remaking and providilding as the case may be all complete as per specification and direction of E/I.
PVC cowl - 100mm dia.
Floor trap - 100mm dia.
ELECTRCIAL WORK
Point Wiring in PVC Conduit, with Modular type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with modular type switch, modular plate, suitable size of GI box etc as required.
Supply and Fixing Light Plug Point with Modular Type Accessories: Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc as required.
Supply and Fixing Light Plug Point with Modular Type Accessories: Supply and Fixing GI box with modular plate and cover in front on surface or in recess including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps modular type switch, connection, painting etc as required.
Supply & fixing 20A SPN MCB Industrial Socket Outlet: Supply and fixing of 20A, 240V, SPN insustrial type socket outlet with 2 poles and earth, metal enclosed plug top along with 20 amps 'C' series, SP MCCB, in sheet steel enclosure, on surface or in recess with chained metal cover for socket out let and complete with connections, testing and commissioning etc as required.
Power plug wiring in PVC conduit (2 X 4 sq,mm) - Wiring for light/power plug with 2 X 4 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, along with 1 no. 4 sq.mm. FR PVC insulated copper conductor single core cable for loop earthing etc. as required.
Circuit / Sub-main wiring in PVC Conduit: Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.
2x1.5 Sqmm + 1x1.5 sqmm earth wire
2x2.5 Sqmm + 1x2.5 sq mm earth wire
2x4 Sqmm + 1x4 sq mm earth wire
4x6 Sq.mm + 2x6 Sq.mm earth wire.
S/F TP MCB DB:- Supplying and fixing of following way, three pole and neutral, sheet steel, MCB distribution board, 415 volts, on surface/recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, detachable gland plate, interconnections, phosphatized and powder painted including earthing etc. as required (Without MCB/RCCB/ISOLATOR). (All TP MCB DB shall be as per IS:8623)
4 Ways (4+12 ways) double door
s/f. VERTICAL TYPE TP MCB DB - Supplying and fixing of following ways surface/recess mounting, vertical type 415 volts TPN MCB distribution bvoard of sheet steel, dust protected, duly powdere painted, inclusive 200amp tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCB's (but without MCB's and incomer) as required (note : vertical type MCB TPDP is norammly used where 3 phase outlets are required)
8 Ways (8+12 ways) double door vertical type
S/F 'C' series MCB:- Supplying and fixing 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.
6/32A Single Pole
6/32A TPN MCB
63A TPN MCB
S/F Ceiling Rose: Supplying and fixing 2 pin ceiling rose on the existing junction box/ wooden block including connection etc as required.
S/F Modular type electronic fan regulator: Supplying and fixing stepped type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required.
ITC Exhaust Fan upto 450 mm sweep: installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.
S/F Batten / Angle Holder: Supplying and fixing batten / angle holder including connection etc as required.
S.I.T.C of following rating surface mounted LED tube light fittings suitable for 230V, 50Hz, single phase supply etc. complete as required - 20/22W. LED tube light
Bulk head fitting with 9/10Watt CFL/LED
Supplying, 15/16 Watt LED bulb of approved make
S.I.T.C. of following rating recess/surface mounted LED round/square shape down light luminaire with pressure die cast housing for single phase supply Voltage. Luminaire shall be confirm to IS:10322 Part -5/section 2 of IEC:62722 with all necessary accessories as required - 18/20W LED round down light
2'X2' LED panel light
Supplying Exhaust fan of 12" (300mm) of aproved make
Supply, installation, testing and commissioning of following size ceiling fan 3 blades confirming to IS:374:2019 including wiring the down rods of standard length (upto 30cm) with 1.5sq.mm. FR. PVC insulated copper wire suitable for 230V, 50Hz, single phase supply etc. complete as required. - 1400mm (56") BLDC star rating 32W ceiling fan
S.I.T.C. of following rating LED street lighting luminarie die cast housing and toughened glass cover (IP-66 portion) in existing pole/pipe for supply voltage 100-270V. AC, 50Hz. Luminaire shall be confirm to IS:10322 part - 5/section 3 and shall be complete with all necessary accessories as required - 100W LED street light
S.I.T.C. of following rating recess/surface mounted LED round/square shape down light luminaire with pressure die cast housing for single phase supply Voltage. Luminaire shall be confirm to IS:10322 Part -5/section 2 of IEC:62722 with all necessary accessories as required - 15/16W LED round down light - as CL
GI Earth Pipe Electrode: Earthing with G.I. earth pipe 4.5 mtr long , 40mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcol and salt complete as required.
Supplying and nlaying 25mm X 5mm G.I. strips at 0.50 metre below ground as strip earth electrode, including connection/terminating with G.I. nut, bolt, spring, washer etc. as required (jointing shall be done by overlapping and with 2sets of G.I. nut bolt & spring washer spaced at 50mm)
Providing and fixing 25mm x 5mm G.I. strip on surface or in recess for connection etc. as required
Provioding and laying 1.1 KV grade aluminium armoured cable as per IS 1554 (Part I) heavy duty all cost complete including cost of brass compression gland, cable jointing and end termination as per specification and direction f E/I.
3.5 core, 95 sq.mm
3.5 core, 50 sq.mm
3.5 core, 25 sq.mm
Supply, installation and commissioning of Slilent type D.G. set of capacity 62.5KVA three phase with AMF Panel IS/IFC60034-1 IS:1460, 13018 (Basic rate + 14.95% C.P. & installation etc.
Laying of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1KV grade of size not exceeding 35sqmm but not exceeding 95sq.mm. direct in ground including excation, and refilling the trench etc. as required but excluding sand cushioning and protective covering.
Supplying and making end termination with brass compression gland and aluminium lugs for following of of PVC insulated and PVC sheathed/XLPE aluminium conductor cable of 1.1KV grade as required 3.5 X 50 sq.mm (35mm)
3.5 X 25 sq.mm (28mm)
3.5 X 95 sq.mm (45mm)
LT. PANEL: Supply, designing, manufacturing, installation, testing and commissioning of Panel fabricated out of 2mm thick (14SWG) CRCA sheet steel duct and verim proof with reinforcement of suitable size iron channel of suitable size with proper lifting arrnagement effecting proper connection of all incomer and out going (IP-43) fully comparatmentalized cubical type wall mounted, totaly enclosed, switch board and suitable for use on 415V, 3 phase, AC supply, 4 wire 50 C/s, system having 25KA fault capacity, housed with incoming and outgoing aluminium bus bars, interconnection, interlocking between feeders etc. wtih indicating lamps push buttons, necessary accessoires, all out going feeders protection as required.
The sheet steel under go minimum 7 tanks treatment followed by finishing of powder coating of minimum 60 micron thickness, duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 nos. earth studs.
All openings shall be covered by soft rubber gasket, enclosure shall be galvanized panel shall have suitable cable entry from bottom and suitable arrangement for multi runs aluminium cables for all MCCB Panel shall have individual compartment with name plate.
Panel size - as per drawing and shall be provieded at the time of work order.
The name plate for each incoming & outgoing feeder mus be adnodised aluminium sheet.
BUS BARS SECTIONS:
The panel includes 415V, 200A, 3Ph, 25KA, 50Hz Electrolytic aluminium Bus bar (E91EWP) aluminium Earth Bus with removable glands plates, cable glands at sending and receiving ends including connection with outgoing feeders complete in all respect. The current density of bus bar shall be minimum 0.8A/sq.mm. Al Bars upto 63A capacity. Other inter connections shall be made with 2.5 and 4 sqmm. PVC Cu. wire.
Make MCCB L & T/ Legrand/ Schnerider/ Siemens/ ABB/C&S
Make of MCB - (10KA-C-Series) L & T/ Legrand/ Schnerider/ Siemens/ ABB/C&S
Make of panel LMD powder Tech/SPC electrotech Pvt. Ltd/EAP, Kolkata/ISG-Ranchi.
The above panel consisting of the following
Incomer : 1 no. 315,415V, 4P/36KA, MCCB with thermo-magnetic based released type with oil S/C protection with adjustable current with spreader links and extended rotary handle., indicator, Digital Ammeter, three phase, Digital Volt-meter - three phase, CT 300/5VA-5 class one epoxy resin cast CT (3 nis,) 1 set - make Kappa/Matrix, Phase indicating light shall be protected by 2 amps SP MCB's for incomer make L & T/AE/Schneider.
Outgoings. - 2 nos., 100A FP/16KA, MCCB with thermomagnetic release type and shall be with spreader links and front rotary handles, 63A TPN/10KA MCB - C series
63Amp DP MCB - 5 nos.
40A TPN/10KA MCB C series 5 nos.
AL bus bar of continious rating 400A
4 Pole MCCB 315A, 35KA with fixed thermal setting
MCCB 100 amps , 16KA fixed thermal setting
40 Amp DP MCB
40 Amp TPN MCB
63 Amp DP MCB
63A TPN MCB
HRC Fuse - 100Amps TP & N for control supply
400Amps 415V heay duty three phase with neutral bus bar chamber
S/F wall/floor mounted cubical panel board fabricated with 16 guage iron sheet suitable for panel mounted switch disconnector including busbar chamber, insulator and painting etc. as required (but without busbar copper chamber)
Electronic timer on delay/off delay for 0 to 30 sec.
Auxilary contactor (1no.+1NC)32A, IS/IEC60947-4-1
LED indicator lamp RYGB
Digital Voltmeter (0-500Volt) 3 phase class 0.5
Digital Amp mtr (0 - 500Amp) 3 phase class 0.5
CT coil of CT ratio 300/5 IS: 2705 part 3
CT coil of CT ratio 800/5 IS: 2705 part 3
50mm X 5mm copper tape (2.30 kg/mtr.)
20mm X mmm copper tape (0.533 kg/mtr)
and cables and wires as required and as per direction of E/I.
BOREWELL
Costs of drilling 200mmX165mmX125mtr. Deep borewell in all kinds of soil and rock in rural area for installation of pump set with Hydraulic DTH rig machine, all complete including supplying all materials, tools, drilling rig, Air compressor and equipments, as well as fuel lubricants and cost of transportation of rig machine and other vehicles upto the site
From 0-50 mtr.
Above 51 mtr.to 125 mtr
Above 125 mtr.
Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia conforming to IS : 12818, including required hire and labour charges fittings & accessories etc. all complete for all depths, as per direction of Engineer-in-charge - 200mm nominal size dia
Gravel packing in tube well construction in accordance with IS : 4097, including providing gravel fine/medium/coarse, in required grading & size as per actual requirement, all complete as per direction of Engineer-in-charge
Development of tube well in accordance with IS 2800 (part 1) and IS: 11189 to establish maximum rate of usable water yield without sand content (beyond permissible limit) with required capacity air compressor, running the compressor for required tile till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, colleting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete including hire & labour charges of air compressor, tools & accessoires etc. all as per requirement and direction of Engineer-in-charge.
Providing & fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/casing pipe, removable as per requirement, all complete for borewell of 200mm dia
Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS:2800 (Part-1) including necessary bolts & nuts of required size complete
Providing and fixing bail plug/bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS :2800 (Part-1) 200mm dia
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pioes having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings. This includes jointing of pipes & fittings with one step CPVC solvent cement trenching, refilling & testing of joints complete as per direction of Engineer in charge
50mm nominal outer dia pipes
Supplying submersible pumps sets confirming to IS:8034 and motor confirming to IS:9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller, motor suitable for working on 415V+10%, 3PH. 50HZ, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thrust, water proof winding shall be provided. the pump set shal be suitable for direct couplings, pump shall have suitable outlet as per manufacture design. Anti thrust stream lined non return valve shall be provided with pump. 3 mtr. submrsible copper conductor cable in single/double run shall be provided with each pump.
Submersible pump set 100mm dia (with polypropylene/noryl impeller) upto 20 stage - 3.0 HP
FIRE FIGHTING EQUIPMENTS
(A) Supplying, installation, testing and commissioning of Electrical driven Main Fire Pump suitable for automatic operation and consisting of following, complete in all respects, as required. (B) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS (C) Suitable HP squirrel cage induction motor, TEFC, synchronous speed 1500 RPM suitable for operation on 415 volts, 3 phase 50Hz. AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class 'F' insulation, confirming to IS 325. (D) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required. (D) Suitable cement concrete foundation duly plastered with anti vibration pads.
2280 lpm at 70 m Head
(A) Supplying, installation, testing and commissioning of eelectric driven pressurisation pump suitable for automatic operation and consisting of following complete in all repsect as required (Jockey Pump) (B) Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with stainless steel shaft, mechanicla seal conforming to IS: 1520. (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50hz AC supply with IP 55 class of protection for enclosure, horiontal foot mounted type with class - F insultation conforming to IS: 325. (D) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required . (E) Suitable cement concrete foundation duly plastered with all anti vibration pads
Jockey pump 180lpm 56m head
(A) Supplying, installation, testing and commissioning of eelectric driven Terrace pump suitable for automatic operation and consisting of following complete in all repsect as required (Terrace Pump) (B) Horizontal type, multistage, centrifugal split casing pump of cast iron body and bronze impeller with stainless steel shaft, mechanicla seal conforming to IS: 1520. (C) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts, 3 phase 50hz AC supply with IP 55 class of protection for enclosure, horiontal foot mounted type with class - F insultation conforming to IS: 325. (D) M.S. fabricated common base plate, coupling, coupling guard, foundation bolts etc. as required . (E) Suitable cement concrete foundation duly plastered with all anti vibration pads
450 lpm 35m head
Fabrication, supply and installation and commissioning of Electrical control panel of cubical of consruction, floor mounted type, fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 fank treatment process, cable alley, inter-connection with suitable size copper conductor cable/solid copper strip, having switchgears and acccessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, suitable for main fire pump pressuresation pump & diesel pump set complete as per CPWD specification with following incmong and outgoings, suitable for operation on 415V , 3 hase, 50Hz AC supply with enclosure protection class IP 42 as required.
Outgoing - All outgoing feeders for pumps should have digital ammeter with slector switches, and LED type on off, trip indicating lamps)
Main fire pump - 125A, 50KA TPN MCCB, Ics=100% Icu, with fully automatic star/Delta starter suitable for 60HP pump with overload protection, current sensing type single phase preventor complkete with all accessories and internal wiring required for automatic operatio, slector switch for local/remote, auto/manual/OFF operation.
System controller : Designing, supply, installation, testing and commissioning of system controller to contorl operation of main electric fire pump, diesel pump, presssurization pump, terrace pump in sequence as per specifcation consisting of relays, timers, sensors, annunciation window for fault indication, complete as per specifcation.
Providing, laying, testing, & commissioning of "C" class heavy duty MS pipe conforming to IS:3589/IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts. Bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required.
25mm dia
32mm dia
40mm dia
50mm dia
65mm dia
80mm dia
100mm dia
150mm dia
Providing, installation, testing and commissioning of non-return valve of following sizes of confirming to IS:5312 complete with rubber gasket, GI bolts, nuts, washers etc. as required 150mm dia
Providing, installation, testing and commissioning of staniless steel Y-strainer fabricated out of 1.6mm thick stainless steel, Grade 304, sheet with 3mm dia. Holes with stainless steel flange. - 150mm dia
Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following size as required.
80mm dia
100mm dia
150mm dia
Supplying and fixing single headed external yard hydrant valve with 1 no. 63mm dia instantaneous FM gunmetal/stainless steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank gunmetal/stainless steel camp and chain as required - Single headed Gunmetal
Supplying and fixing 63mm dia. 15M long RRL hose pipe with 63mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required Gun metal
Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, confirming to IS 884 complete with the following as required. 20mm nominal internal dia water hose thermoplastic (textiles reinforced) tye 2 as per IS: 12585, 20mm nominal internal dia gun metal gflobe valve & nozzle. Drum and brackets for fixing the equipments on wall. Connections from riser with 25mm dia stop gun metal valve & M.S. pipe socket. 30M
Supplying & fixing 63mm dia gun metal short branch pipe with 20mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required : Stainless steel (Grade 304)
Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories.
Pendent sprinkler
Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required
Supplying and fixing air vessel made of 250mm dia 8mm thick M.S. sheet, 1200mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25mm dia gun metal wheel valve with required accessories, presure guage and painting with sysnthetic enamel paint of approved shade as required.
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
ADD: GST @ 18%...
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
ADD: LABOUR CESS @ 1%...
TOTAL OF SCHEDULED ITEMS
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
PART -B - NON SCHEUDLED ITEMS
Providing and fixing Carbon di Oxide fire extinguisher consisting of welded MS cylindrical body, squeeze lever, discharge valve, fitted with internal discharge tube, high pressure discharge hose, discharge nozzle, suspension bracket, finished externally with red enamel paint, & fixed to wall with brackets with initial charger.Make :- Kartar/Safeguard/ATASEE
Capacity 4.5 kg ISI Marked
Providing and fixing ABC Extinguisher consisting of welded MS cylindrical body with discharge valve, nozzle and hanging arrangement complete.Make :- Kartar/Safeguard/ATASEE
a) Capacity 6 kg ISI Marked
B) Foam Type Extinguisher 9LTR
FIRE BUCKET
iiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiiii
All the supply of furniture will be subject to the approval from the competent authority.
Supplying and placing of Training Chair,Material & Subtype Premium Leatherette Upholstery Material Premium Leatherette Seat Material Premium Leatherette Finish Matte Colour & Colour Family Brown - Smoke Oak Dimension (W)600mm X (D)500mm X (H)820mm Seating Capacity 1 Seater Seating Height 465mm Size Standard Style Modern Assembly Type Knock DownThe product must be from a Manufacturer having ISO 9001,ISO 14001,,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of Table,Material & Subtype Engineered Wood - Particle Board Table Top Material Engineered Wood Finish Matte Colour & Colour Family White - Maple Dimension (W)1200mm X (D)600mm X (H)750mm Table Top Thickness 25 mm Assembly Type Knock Down .The product must be from a Manufacturer having ISO 9001,ISO 14001,,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of Medium Back Chair,Material & Subtype Mesh - Fabric Upholstery Material Mesh Seat Material Fabric Leg Material Nylon Finish Matte Colour & Colour Family Black Dimension (W)585mm X (D)660mm X (H)1060mm Mechanism Synchro Single Locking Seating Capacity 1 Seater Maximum Seating Height 570 Function Revolving,Pneumatic Height Lift,Tilt Tension Control Size Standard Style Modern Assembly Type Knock Down The product must be from a Manufacturer having ISO 9001,ISO 14001,,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Providing and supplying non-sharing single unit workstation table in completely knock down conditions with an overall size 1200mm x 600mm x 1200mm that is to be assembled at site. The work top shall have the size 1184mm x 592mm made up of 25mm thick pre- laminated particle board of grade ii type iii of is 12823/latest . Of is level with approved laminate and finish as per approved shade. * the profile of the top shall be in rectangle shape and the edges shall be sealed with 2mm thick thin strip of impermeable pvc that is cut to fit the size of board panel and duly pasted with the assistance of edge banding machine at 200 degree celsius. * the top trim, top bar, mid bar, vertical bar, raceway, skirting shall be made up of aluminium extrusions (pre-treated) and duly powder coated with polyester powder coating 40p-60p thick . The trims shall have the size 67mm x 19mm with 1.5mm thick covered with die cast end caps on joints 2 ways, 3 ways & 4 ways (l-cover for corner, t?cover for middle section wherever required). The aluminium raceway shall be situated below the worktop with an overall size 116mm(h) x 60mm(d) with 1.4 mm cover thickness and 2mm back thickness as per requirement of inlaying the electrica management and carrying the wire horizontally.*the exposed vertical and horizontal faces of the frames shall be snap fitted with trims. There shall be soft-board (with fabric) and marker board provided at front of the user. Laminated top tile and bottom tile shall be situated at both sides of the user and below the work top respectively. telecommunications and data (lan) and has separate components for electrical, data and telephone cables having adequate capability of both the vertical and horizontal wire movements. Slots/cut-outs should be given on raceways to fix all electrical and data points. Single sided pvc wire manager should be enclosed at table top.adjustable leveller shoe shall be provided at bottom of the partition to avoid scratches on the floor. The product must be from a manufacturer having iso 9001,iso 14001,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of Tables,Material & Subtype Engineered Wood - Particle Board Table Top Material Engineered Wood Finish Matte Colour & Colour Family White - Maple Dimension (W)1200mm X (D)600mm X (H)750mm Table Top Thickness 25 mm Assembly Type Knock Down Storage Type Drawers The product must be from a Manufacturer having ISO 9001,ISO 14001 ,, AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of Revolving Chair,* Medium back 360° degre revolving chair sku : define/mb/eco , * all over size is : 610mm(l)x 470mm(d)x 1040mm(h) , *the chair made of full mesh in black colour . It will comes in matte finsih about style type is gf nylon structure with nylon net on back . Details : * * arms : fixed pp armsrest . * use of ply: 12 mm thick hot pressed bwr plywood (is grade - 303 for seat). * seat: 40 ± 2 mm thick polyurethane foam with density 32 (±3) kg per cu meter for best quality cushioning in seat , * back : frame of design shall be curved made of two pieces injection moulded frame cover with mesh .backrest support adjustable lumbar support * mechanism : single locking mechanism . * gas lift 100 mm telescopic haudraulic * base : 650mm nylon base with smooth castors The product must be from a Manufacturer having ISO 9001,ISO 14001 ,,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of Chairs,* fix cantiliver back supported powder coated fix cantilever frame chair all over size is 520mm(L)X472mm(D)X930mm (H). The chair made of full fabric in black colour, it will comes in mattee finish in contemporary style details Arms fixed armrest padded armrest, use of ply: 12mm thick hot pressed BWR plywood (IS grade 303 for seat and back) seat 40mm thick polyrethane foam with density 32 kg per CUM for best quality cushioning in seat back 40+-2mm thick polyrethane foam with density 32mm +- kg per cum, for best qualtiy cushioning in back, back mrest support foram design based on symmetrical lumbar support. Only seat sizxe is 520mmX470mmH. Back height is 930mm, fixed cantilever chai base M.S. plwder coated tubular frame of cantilever type The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of Desk Bench,• An overall size 1800mm X 950mm X 760mm. • The top of the desk shall be made upof 18mm thick particle board of grade II as per IS 12823 with approved laminate. •Top, Seat & Back made out in 18mm PLB with PVC edge band• The top shall be supported on CRCA pipe having cross-section area 25mm X 25mm with1.2mm thickness. • The shelf shall be made up of 0.8 mm thick high yield strengthCRCA sheet of grade ‘D’ confirming to IS: 513. It should be supported on CRCA rectangle pipe having cross sec on area 19.05mm X 19.05mm with 1.2mm thick. • The side panel of the table shall be made of 1mm thick CRCA sheet in folded construction, which has intrinsic rigidity with the assistance of 19.05mm X 19.05mm rectangle pipe placed in vertical position. • Hooks should be provided on the vertical side frame on both side of the desk for hanging bags/bottles. • The front of the desk shall be clad with modesty panel made up of 0.8mm thick CRCA sheet with square perforation for aesthetically appealing. • The seat and back shall be supported on CRCA square pipe having cross-section area 25mm X 25mm with 1.2mm thick welded together with 25.4mm X 1.2mm thick round pipe. • The side panel of the bench shall be made up of 1mm thick CRCA sheet which have folded construction with the assistance of 19.05mm X 19.05mm X 1.2mm thick square pipe. • 02 nos. footstep shall be provided for structural support of the desk having cross sec on area of the pipe 25mm X 25mm with 1.2mm thick. • The complete steel structure shall be welded with base pipe having cross-section area 50mm X 25mm with 1.2mm thick and also be epoxy polyester powder coated to the thickness 50-60μ thick. • The size of the writing top shall be 1800mm(W) X 390mm(D), seat size shall be 1800mm(W) X 300mm(D), back size shall be 1800mm(W) X 150mm(H). • All the size shall have the tolerance of upper and lower deviation of ±10mm for board & ±0.2mm for metalThe product must be from a Manufacturer having ISO 9001,ISO 14001,,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of Almirah, Metal storage of size 900mmX450mmX1980mm, body made out in 22 gauge (0.8mm) & door 19 gague (1mm) CRCA sheet, 4 adjustable shevle in 22 gague (0.8mm) & pedestal 18gague 1.2mm CRCA sheet, having four shelves making five compartment, uniformly distributed load capacity of each shelf shall be 60kg maximum, fitted with MS body lock & handle finishing with Epoxy polyester powder coated to the thickness 50-60 microns(+/-5) micron) in colour grey-light grey The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
* Supplyiung and placing Main Table,DIRECTOR DESK : Director table structure of curves shape desk, primary work surface over all size is 1800mmX900mmX760mm 50mm thick table top made of prelaminated particle board work surface with glossy walnut finish same matching edge banding made of same matte finish side panel is made of 45mm thick provision of side runnera of size is 1400mm X 400mm X 660mm (construction is 1 openable door + 1 open shelve for CPU back side have 3 holes in between both 1 key board tray with telescopic channel & 1 open box storage 550mmX350mm from down drawer, 2 drawers mobile pedestal of size 400mmX480mmX550mm, having 2 drawers with castors in provided with central lock for security and given curved shaped upper drawer are provided for easy of opening. Overall construction of pedestal is 18mm along with facia of drawers, three layer prelaminated particles board (wood product) of grade III type III of IS 12823/Latest. The product must be from a Manufacturer having ISO 9001,ISO 14001 ,, AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of visitor chair: fix cantilever chair. All over size is 580mmX525mmX970mm. The chair made of full leatherette in black colour. It will comes in matt finish in contemporary style. Details arms: fixed arms PP connected with seat and back. Use of ply: 12mm thick hot pressed BWR plywood (IS grade 303 for seat and back) seat 40(+-2)mm thick polyurethane foam with density 32(+-3) kg per CUM for best quality cushioned in seat. Back 40(+-2)mm thick polyurethane foam with density 32(+-3) kg per CUM for best quality cushioning in back. Backrest support form design based on symmetrical lumbar support. Only seat size is 525mmX525mm and the back size is 580mmX550mm. fixed cantilever chair , base MS powder coated tybular frame of cantilever type The product must be from a Manufacturer having ISO 9001,ISO 14001 ,, AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of Chairs,* Fix cantiliver back supported power coated fix cantiliver frame chair . All over size is 520mmX470mmX930mm. The chair made of full fabric in black colour. It will comes in matt finish in contemporary style. Details arms fixed armrest padded armrest. use of ply 12mm thick hot pressed BWR plyoow (IS grade 303 for seat and back) seat 40(+-2mm) thick polyurethane foam with density 32(+-3)Kg per CUM for best quality cushioning in sear, back 40(+-3)kg per CUM for best quality cushioning in back. Back rest support foam design based on symmetrical lumbar support. Only seat size is 520mmX470mm. Back height is @ 930mm. fixed cantilever chair. Base MS powder coated tubular frame of cantiliver type The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of 29 Seater Conference Table,* Providing and supplying U-shape modern design conference table and in between U shape table top length is 22900mm, table top offers a generous workspace, desk primary work surface use premium quality materaisl over all size is 22900mmX600mmX750mm. table top made of 36mm thick which give more surface area for work machine made modular furniture made prelaminated particle board of grade II type III of IS 12823/latest. Construction provision of conference tabletop supported with 18mm thick side pannels in brown-black oak colour made by prelaminated particle board and below the top 18mm thick prelam particle board modesty panel and work surface furniture is finished with exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade fixed with hot melt glue. The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of High Back Chair,* High back 360 degree revolving chair. All over size is 640mmX480mmX1240mm. The chair made of full mesh in black colour. It will comes in matt finish in contemporary style. Details arms: armest is having two adjustment height (up & down) use of 12mm thick hot pressed BWR plywood (is grade : 303 for seat: seat 40(+-2mm) thick polyurethane foam with density 32(+-3) kg per CUM for best quality cushioning in seat. back frame of design shall be curved made of two pieces injection moulded frame cover with mesh back rest support adjustable lumbar support, mechanism, self weighted multi locking mechanism, gas lift 100mm telescopic haudraulic, base 650mm chrome base with smooth castors. The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of Medium Back Chair,* Medium back 360 degree revolving chair. All over size is 610mm X 470mm X 1040mm. The chair made of full mesh in black colour. It will comes in matt finish about style type is GF nylon structure with nylon net on back. details: Arms fixed PP armsrest. Use of ply 12mm thick hot pressed BWR plywood (IS gramde 303 for seat). Seat 40(+-2mm) thick polyurethane foam with density 32(+-3) Kg per CUM for best quality cushioning in seat, back frame of design shall be curved made of two pieces injection moulded frame cover with mesh backrest support adjustable lumbar support mechanism: single locking mechanism, gas lift 100mm telescopic haudraulic, base 650mm nylon base with smooth castors, The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of Tables,Material & Subtype Engineered Wood - Particle Board Table Top Material Engineered Wood Finish Matte Colour & Colour Family White - Maple Dimension (W)1200mm X (D)600mm X (H)750mm Table Top Thickness 25 mm Assembly Type Knock Down Storage Type Drawers The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of Auditorium Chair,High Back of trade pattern with cup holder,# Size : 560 mm ctc # Pushback & auto tip # M.S. Tubular frame structure. # 3 mm Foam laminated fabric. # Moulded PU foam above 48 density. # PPCP handle with cup holder. # Sliding Pushback mechanism. # PPCP tray cover for Seat & Back. # Seat numbering for seat & back both. # Row numbering. # Black powder coating surface. # Auto tip up feature. # Common sharing handle The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of Office Table,Office desk desk structure of l shaped desk . Primary work surface over all size is 1500mm(l)x 600mm(d)x 750mm(h) 25mm thick table top made of prelaminated particle board work surface with the exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade with the hot melt glue . Modesty pannel 18made of mm thick . *provision of side unit of size is 900mm(l)x 450mm(d)x 750mm(h) ,(combination construction wire management hole with pvc grooment on table top, left side table top based on a 18mm thick side pannel engineered wood & from right side unit have 2 sliding door + 1 fixed shelve . *side unit size 900mm(l)x 450mm(d)x 750mm(h), in provided with lock for security and handles are provided for easy of opening. Overall construction of side unit is 18mm thick along with fecia of slidding shutters. *three layer prelaminated particles board(wood product) of grade ii type iii of is 12823/latest The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of Chairs,* Fix cantilever back supported powder coated fix cantilever frame chair. All over size is 520mmX470mmX930mm. The chair made of full fabric in black colour. It will comes in matt finish in contemporary style, details: arms fixed armrest padded armrest. Use of ply 12mm thick Hot pressed BWR plywood (IS grade 303 for seat and back). Seat 40(+-2mm) thickk ployurethane foam with density 32(+-3) Kg per CUM for best quality cushioning in seat back 40(+-2mm) thick polyurethane foam wth density 32(+-2)mm kg Per CUM for best quality cushioning in back, backrest support foam design based on symmetrical lumbar support. Only seat size is 520mmX470mm.back height is 930mm fixed cantilever chair base M./S. powder coated tubular frame of cantilever type. The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing three Seated exclusive premium leatherete modernist classic design lounge sofa size is 1920mm X 780mm X 740mm(H) with kiln dried wood framing makes it warp and scratch resistant comfortable seat depth & height designed keeping modern Indian Life style in mind wraped in buttery-soft premium leatherette/classic button-tufting. The panelled back and cushioned armests ecourage lounging designed with modernity & elegance, choose the option that suits your home. combination construction structures are made in moisture content shall be less than (10-12%). thickness of plywood used shall be 12mm grade is 303 Indian standard fr commercial (common) and mositure proof plywood (tentative) understructure frame shall be constructured from 18mm thick kiln-dried German Beech wood framing is highly durable. the button-tufted backrest and firm seating offers the right amount of support. The complete structures shall be covered by P.U foam fixed with adhesive glue. The frame shall be padded with high resilience polyurethane foam having 66+/-5 density density innseat it shall be stack foam of 66mm thick 66mm thick back form having 66+/-5 density foam used, There shall be cushion arm 66mm thick provided padded wth hgih resilience polyurethane foam having densing 66+/-5. the complete stack foam strucutre shall be overed with premium leatherette. It complements the modish legs are made by rough shape in PVC material. seat height 410mm. The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of Table primary work surface over all size is 1200mmX600mmX730mm(H) 18mm thick table top made of prelaminaed particle board work surface with the exposed edges shall be finished with 2mm thick edge binding tape of mathcing colour and shade with the hot melt glue.The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of main table made of prelaminated partcile board with slantlegs 50Xx50mm M.S. understructure in powder coating 2 stop made of 25mm thick prelaminated particle board in frosty white colour with main table size 1200mm X 1200mm . The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of low back chair material & subtype premium leatherette upholstery material premium leatherette seat material premium leatherette finsh matt dimesion 571mmX460mmX820mm(H) seating capaicty 1 seater function stackable size compact style modern. The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of rack - Sloted angle rack of size 900mm X 450mm X 2000mm (H) slotted angle rack - closed from two side 7 shelves including top & bottom angles 40mmX40mmX2mm thick. Shelf 36X15X1mm CRCA sheet in colour grey The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of Almirah : Metal storage size 900mm X 450mm /x 1980mm (H) body made out in 22 gague (0.8mm) & door 19mm gague (1mm) CRCA sheetr. 4 adjustable shelve in 22 gague (0.8mm) & pedestal 18 gague 1.2mm CRCA sheet having four shelves making five compartment, uniformly distributed load capacity of eah shelf shall be 60kg maximum, fitted with M.S. body lock & handle. Finishing with epoxy polyester powder coated to the thickness of 50-60 mircons (+/-5 micron) colour grey light grey The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing Reception table of approved size The product must be from a Manufacturer having ISO 9001,ISO 14001,,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
MAIN TABLE FOR OFFICE 1 NOS 119660 119,660 Supplying and placing of Main Table,Director desk director table structure of l-shape desk . Primary work surface over all size is 2000mm(l)x 950mm(d)x 760mm(h) 50mm thick table top made of prelaminated particle board work surface with glossy walnut finish same matching edge banding made of same matte finish. Side pannel is made of 45mm thick. * provision of side runner/a of size is 1400mm(l)x 400mm(d)x 660mm(h) ,(construction is 1 openable door + 1 open shelve for cpu back side have 3 holes ,in between both 1 key board tray with telescopic channel& 1 open box storage (l) 550mm x (h) 350mm from down 1-drawer . * 2 drawers mobile pedestal of size 400mm(l)x 480mm(d)x 550mm(h) , having 2 drawers with castors in provided with cetnral lock for security and given curved shaped upper drawer are provided for easy of opening. Overall construction of pedestal is 18 mm along with fecia of drawers. * three layer prelaminated particles board(wood product) of grade ii type iii of is 12823/latest The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
Supplying and placing of Office Table,Office desk desk structure of l shaped desk . Primary work surface over all size is 1500mm(l)x 600mm(d)x 750mm(h) 25mm thick table top made of prelaminated particle board work surface with the exposed edges shall be finished with 2mm thick edge binding tape of matching colour and shade with the hot melt glue . Modesty pannel 18made of mm thick . *provision of side unit of size is 900mm(l)x 450mm(d)x 750mm(h) ,(combination construction wire management hole with pvc grooment on table top, left side table top based on a 18mm thick side pannel engineered wood & from right side unit have 2 sliding door + 1 fixed shelve . *side unit size 900mm(l)x 450mm(d)x 750mm(h), in provided with lock for security and handles are provided for easy of opening. Overall construction of side unit is 18mm thick along with fecia of slidding shutters. *three layer prelaminated particles board(wood product) of grade ii type iii of is 12823/latestThe product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
CHAIR FOR SEMINAR HALL Supplying and placing of Auditorium Chair,High Back of trade pattern with cup holder,# Size : 560 mm ctc # Pushback & auto tip # M.S. Tubular frame structure. # 3 mm Foam laminated fabric. # Moulded PU foam above 48 density. # PPCP handle with cup holder. # Sliding Pushback mechanism. # PPCP tray cover for Seat & Back. # Seat numbering for seat & back both. # Row numbering. # Black powder coating surface. # Auto tip up feature. # Common sharing handle The product must be from a Manufacturer having ISO 9001,ISO 14001 ,AIOTA BIFMA Compliant, Green Guard Sedex Certificate, make Durian/Palghar/Maple with 5 years warranty all complete
AIR CONDITIONING WORK
Supply, installation, testing & commissioning of Air conditioning system of approved make with the following specifications: (subject to the approval of the authority.
VRF Outdoor Unit
Supply, Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Cooling Only Outdoor units with Inverter Scroll Compressor of required Nominal capacity. The operational cooling range should be from -5 deg C to 54 deg C ambient DBT.
VRF Indoor Units
4 Way Cassette Unit
Supply, Installation, Testing and Commissioning of 4-way flow type Cassette Units of required nominal capacity & as per specification.
1 Way Cassette Unit
Supply, Installation, Testing and Commissioning of 1-way flow type Cassette Units of required nominal capacity & as per specification.
HI-WALL SPLIT TYPE AC UNIT
Supply, Installation, Testing and Commissioning of 1 WAY CASSETTE Units of required nominal capacity & as per specification.
DUCTABLE TYPE AC UNIT
Supply, Installation, testing and commissioning of Ceiling Suspended VRF Hi-Static Ducted unit with multispeed motor, drain pan, cooling coil etc as required as per specifications.
17 TR Hi-Static Ducted unit
TFA UNIT
Supply, Installation, testing and commissioning of Ceiling Suspended VRF Hi-Static Ducted unit with multispeed motor, drain pan, cooling coil etc as required as per specifications.
REFRIGERANT PIPING
Supply, Installation, testing & commissioning of copper refrigerant pipe work with 13mm/19mm thick closed cell elastomeric nitrile rubber tubular insulation between indoor & outdoor units as per requirement.
UPVC DRAIN PIPE
Supply, fixing, testing & commissioning of UPVC pipes complete with insulation and all necessary fittings such as elbows, tees, reducers etc. and supports such as clamps etc. complete as per specifications.
Y-JOINT
Supply, Installation, Testing and Commissioning of Y-joints for various pipe sizes and headers etc. as per requirement.
DUCTING WORK
Supply, installation, balancing and commissioning of site fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.
Supplying & fixing of powder coated extruded aluminium Supply/Return Air Grills without aluminium volume control dampers as per required.
Supplying & fixing of Thermal Insulation of duct as per requirement & specification.
COMMUNICATION & CONTROL CABLE
Supply and laying of flexible cu cabling inside pvc conduit pipe for communication from indoor units to outdoor units.2C X 1.5 Sqmm
10 PASSENGER LIFT
Supply, installation, testing and commissioning of 10 passenger lift of approved make with the following specifications:
Add GST 18 %
Add Labour cess 1%
M/S MANOJ KUMAR PANDEY (BID ID -630289)
Bidder Name
M/s Satyam Builders
M/S MANOJ KUMAR PANDEY
stage.html
html • 0.04 MB
tech_bid_open.pdf
tech_eval.pdf
fin_bid_open.pdf
boq_comp_chart.xlsx
xlsx
fin_eval.pdf
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid