Provn of guard room driver rest room and certain minor works of various location at Misa camp under GE S Tezpur

Amount

Excavation in post holes (or similar holes) each n exc 0.5 Cum getting out , returning , filling in and ramming earth or broken rubble mixed with earth around in layers not exceeding 25 cm in hard cement concrete ,Complete all as specified and directed.

Surface excavation n. exc. 30cm deep and avererging 15cm deep and getting out excated soil not exc 50.0 metre distance.Complete all as specified and directed

Surface dressing n.exc 15 cm deep in soft/loose soil complete all as specified and directed.

Excavation over area n exc 1.50 mtr in depth and getting out in hard/dense soil complete all as specified and directed.

Excavation in trenches n exc 1.5 mtr depth and n exc 1.5 m wide in soft/loose soil and getting out.Complete all as specified and directed

Removing excavated Material (Soil) not exc. 50.00 Metre and depositing where directed at a level not exc. 1.50 Metre above the starting point, complete all as specified and as directed.

Returning/Filling in trenches in layer n exc 25 cm thick including watering well ramming etc.Complete all as specified and directed

M&L Plain Cement Concrete type D2 (1:4:8) using 40 mm graded aggregate as in Foundation, Filling and Mass Concrete, complete all as specified and as directed.

M&L for PCC 1:2:4 type B1 using 20 mm graded aggregate as in concrete bed to septic tank.Complete all as specified and directed

M&L Pre-cast Reinforced Cement Concrete type B1(1:2:4) using 20 mm graded crushed stone aggregate) as in Cover Slab of Man Holes, Septic Tanks, etc., set in Cement Mortar 1:4 including necessary forms, moulds, etc., complete all as specified and as directed. NOTE : Reinforcement shall be measured and paid separately under relevant Item.

M&L Reinforced Cement Concrete (Design Mix) M-25 in Foundations including Rafts, Footings, Foundation Beams; Plinth Beams; bases for Columns, etc.; Basement Slabs, Under-reamed Piles and Mass Concrete, complete all as specified and as directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

M&L Reinforced Cement Concrete (Design Mix) M-25 in Columns, Pillars, Piers, Posts and Struts, etc. complete all as specified and as directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

M&L Reinforced Cement Concrete (Design Mix) M-25 as in roof slab supported on wall, beam, landing, desk slab etc complete all as specified and directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

M&L Reinforced Cement Concrete (Design Mix) M-25 in Chajja, etc., complete all as specified and as directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

M&L Reinforced Cement Concrete (Design Mix) M-25 in Roof Beams, Cantilevers, Bres-summers, Lintels over 1.50 Metre Span, complete all as specified and as directed. NOTE : Formwork and Reinforcement shall be Measured and Paid for separately under relevant Items.

Use & waste of form work of the side of the concrete foundation, footing, base of column rough finished flat surface.Complete all as specified and directed.

Use & waste of form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick ( Horizontal or sloping).Complete all as specified and directed.

Use & waste of form work to the side of the column , rough finished flat surface area.Complete all as specified and directed.

Use & waste of formwork to side and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, verhangs etc also plays between floors and beams etc.Complete all as specified and directed.

Use & waste of formwork to edge of concrete flats, breks in flooors, openings in concrete walls , floors and roofs and sides of RCC/PCC bands in walls, horizontal or loppin and similar work all exceeding 20 cm wide(Where RCC/PCC band in walls spanning and opening , the formwork soffit only shall be paid for under item 7010 of SSR Part-II.Complete all as specified and directed.

Use & waste of formwork to chullah hoods, chajjas, trough and similar items including edges finished rough surfaces of concrete.Complete all as specified and directed.

M&L TMT Bars 10 mm dia and over, cut to length, bent to shape required including crank-ing, bending and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm, complete all as specified and as directed.

M&L TMT Bars 5 mm dia and over but not exc 10 mm dia , cut to length, bent to shape required including crank-ing, bending and binding with and including Mild Steel Wire (annealed) not less than 0.90 mm, as in stirrups spacers and binders complete all as specified and as directed.

M&L Brickwork with fly ash bricks straight or curved on plan exc 6 m mean radius built in Cement Mortar 1:6, complete all as specified and as directed.

M&L Brick work using sub class ‘B’ bricks (old size) straight or curved on plan to any radius in half brick work built in CM 1:4 complete all as specified and as directed.

M&L for Brickwork, with subclass ‘B’ bricks in one brick thick honey comb work, built in CM(1:4) complete all as specified and as directed.

M&L Rendering 20mm thick in Cement Mortar on fair faces of brick work or concrete surface of wall in two layer, first layer 10 mm thick in cement morter (1:4) and top layer 10mm thick in cement morter (1:4) using water proofing compound and finishing the surface even and smooth without using extra cement complete all as specified and as directed. . (NOTE:-WPC shall be measured and paid separately)

M&L Rendering 15mm thick in Cement Mortar 1:6 on Brick Walls or on Concrete Surfaces, finishing plastered surfaces Even and fair without using Extra Cement complete all as specified and as directed.

M&L 5 mm thick plastering on ceilling concrete surface in cm (1:3) even and smooth w/o using extra cement.complete all as specified and as directed.

Supply only integral water proofing compoundcomplete all as specified and as directed.

M&L for Earth filling out side of MOD land under floor or in foundation including watering as required.complete all as specified and as directed.

M&L Damp proof course 25 mm thk in PCC 1:2:4 type B-0 to horizontal or vertical surface.complete all as specified and as directed.

M&L for 40mm thick .Cement Concrete 1:2:4 type B1 using 20mm graded aggtregate as in floor finshed even and smooth without using extra cement.complete all as specified and as directed.

M&L for 75mm thick Plain Cement concrete 1:3:6 type C2 using 40mm gradded aggregate as in bedding of foothpath,sub base.complete all as specified and as directed.

M&L 75mm thick PCC 1:3:6 type C2 using 40 mm graded stone aggregate as in path/pavings finished rough and laid in alternate bays to receive chequered tile all as specified and directed.

M&L Hard core of broken stone or boulder of gauge n exc 63 mm of broken boulder bellow plinth protection/hard standing/floor.complete all as specified and as directed.

M&L Loose filling with broken bricks aggregates of gauge 80 to 150 mm in soakage pits, soakage wells complete all as directed.

M&L for supply, laying, jointing and testing salt glazed stone ware drain pipe, grade 'A' 150mm bore (internal dia) laid in trenches on concrete bed to required slope jointed and tested complete all as specified and directed by the Engineer-in-Charge. (Note:- Excavation/earth work and concrete bed shall be measured and paid for separately)

M&L Plain cement Concrete 1:3:6 type C2(Using 40mm graded agg) for concrete bed to drain pipes of 150mm bore, under and haunching against the sides of pipes after they are laid and tested in complete all as specified and directed by Engineer-in-Charge

M&L Non skid ceramics tiles Coloured tiles 7 to 8mm thick (square/ rectangular), area of each tile exc 0.06 sqm but not exc 0.11 sqm as in floors over and including 15mm thick screed bed/bedding layer in CM 1:6 set and jointed in neat cement slurry and pointed in white/coloured cement to match the existing floor complete all as specified and as directed.

S&F Colour Glazed ceramic tiles 450x350mm of 7 to 8mm thick, in dado/skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick rendering in CM 1:4 on brick or concrete surfaces for fixing of tiles in wall.complete all as specified and as directed.

M&L Granite (of any type) Work (Table rubbed and polished) 18 to 20 mm thick, in Steps, Cooking Platforms and like, Set in Screed bed of 15mm thick in Cement Mortar 1:4 including Pointing in White Cement 1:2 using Marble Dust with admixture of Pigment to match with Shade of Granite including Cutting and Polishing including half round edges, complete all as specified and as directed.

S&F Machine cut kota stone slab flooring 20-25mm thick (size min 550x 550)laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (Granite Finish Polishing) complete over 15mm thick 1:6 cement mortar screed bed complete all as specified and as directed.

S&F Machine cut kota stone slab 20-25mm thick on Vertical Surfaces such as Skirting, Dados, Risers to Steps, etc. Set and Jointed in Neat Cement Slurry and Pointed in White or Coloured Cement to match the Shade of the Tiles over 10 mm thick backing layer in cement mortar (1:4) including rubbing and polishing complete all as specified and as directed.

S&F Chequered cement concrete coloured tiles (glossy finish) 20cm x 20cm x 25 mm thick set, jointed and pointed in neat cement slurry with grey cement and pigment including 15 mm thick screed bed or bedding layer of mortar in CM 1:6 fixing of tiles in floor. complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60 mm thickness M-35 Grade over 100 mm sand cushion over rammed earth complete all as specified and as directed.

Forming Constrution (Dummy) joints 30 mm deep x 10 mm wide, filled with sealing compound grade A.complete all as specified and as directed.

M & L for two coats of exterior emulsion antifungus paint by smart painting method over a coat of damp shield wall primer over a coat of 3 mm thick wall care putty to wall including preparation of new wall surface.complete all as specified and as directed.

M&L Preparation of new plastered surface of wall and applying three coats of white wash.complete all as specified and as directed.

M&L Preparation of new plastered surface of ceiling and applying three coats of white wash.complete all as specified and as directed.

M&L for and applying two coats of cement base paint over a coat of wall primer on exterior wall includings preparation of new wall surface.complete all as specified and as directed.

M&L applying two coats of acrylic emulsion distemper by smart painting method over a coat of damp shield wall primer over a coat of 3mm thick a layer of wall care putty on new wall surface.complete all as specified and as directed.

M&L Mild Steel Flat Iron 25 x 3 mm, as in Holdfast for Door, Window Frames or Chowkats etc., cut to length or drilled hole and fixed with Screw, etc., grade of Steel conforming to Fe-290 Gde E-165, complete all as specified and as directed.

M&L Plain Cement Concrete type B-1, (1:2:4) (20mm graded crushed stone aggregate) as in Coping bed plate,hold fast etc,block benching,channeling slightly rounded or chamfered angle and throating including form work and finishing all exposed faces of cement concrete complete all as specified and as directed.

S&F Steel window without glazing bars but with FI/Z section for fixing of gauze and steel handle, peg stay complete all as specified and directed by Engineer-in-Charge .

S&F Steel window side hung shutters including box type hinges with steel handle and steel pegs stay complete with glazing bars and fly proofing completed.

S&F steel ventilators with top hung shutters including hinges, steel peg stay, complete all as specified and directed.

M&L for MS framed work such as grills, gratings, etc.. with ends of bars shouldered , walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed.

S&F Mild steel rolled section conforming to Fe-290 (Gde E-165), as in main and cross beams, hip and jack rafters, purlins where connected to common rafters fixed with angle cleats and other connecting plates etc. complete all as specified and directed.

M&L for MS framed work of angle, tee, F.I, conforming to Fe-290 (Gde E-165), as in roof trusses including distance pieces, cleats etc. welding or riveted complete all as specified and directed.

S&F Mild steel framed work conforming to Fe-290 (Gde E-165), as in doors or gates of angle or other section with gusset plates, rails, braces, etc. complete drilled for fixing steel sheeting or other covering to be prepare for hanging including either hooks or hinges etc.complete all as specified and directed.

S&F Steel work in tubular/square/rectangular hollow section/angle iron, tee etc. for structural trusses including special shaped washer etc. complete using ERW or induction butt welded tubes using Fe as per IS 4923, Grade YST 310 including necessary machinery for upto 10m height structure complete in all respect as specified and directed.

S&F Mild steel screw bolts (machine made), diameter of neck 16 to 20mm, length of bolt exc 22.5cm and n exc 30cm longwith hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut complete all as specified and directed.

M&L Preparing new Wood and Wood Based Surfaces of any description, over 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Pink Primer, complete all as specified and as directed.

M&L Preparing new Steel or Iron Surfaces of any description, exe 10 Cm width or girth and applying Two Coats of Synthetic Enamel Paint (First quality) over a coat of Red Oxide, Zinc Chrome Primer, complete all as specified and as directed.

S&F 3 mm thick ordinary quality sheet glass in squares n exc 0.5 sqm in each pane glazing with oil putty completecomplete all as specified and as directed.

S&F Stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperature 1.18 mm fitted with tinned tacles or galvanised wire staples complete all as specified and as directed.

M&L Pressed steel frames for doors with one or more rebates size of frame 125 x 60 mm including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed as in repair complete all as specified and directed. Note :- Pressed Steel Frame should be filled with PCC 1:3:6 Type C-0 (Using 12.50mm graded stone aggregate) and cost of PCC shall be deemed included in quoted rate

S&F Factory Made Solid PVC Door Frame of size 50 x 47 mm made out of 5.0 mm thick plain colour PVC Sheet reinforced with Mild Steel Square Tube, fixing in opening as per Specifications and Drawings shown in MES Schedule Part-II, complete all as specified and as directed.

S&F Factory Made Solid Panel PVC Door Shutter 30mm thick, consisting of frame made out of Mild Steel Tube of 19 Gauge thickness and size of 19mm x 19mm for Stiles and 15mm x 15mm for Top & Bottom Rails. Mild Steel Frame shall have a coat of Steel Primer of Approved Make and Manufacturer. Mild Steel Frame shall be covered with 5.0mm thick heat moulded PVC 'C' Channel of size 30 x 50mm forming Stiles and 5.0mm thick, 75mm wide PVC Sheets For Top Rail, Lock Rail & Bottom Rail on either side, and 10mm (5.0mm x 2) thick, 20mm wide Cross PVC Sheet as gap insert for Top Rail, Lock Rail & Bottom Rail. Panelling of 5.0mm thick PVC Sheet Beading on either side and joined together with Solvent Cement Adhesive, etc. An additional 5.0mm thick PVC Strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC Solvent Adhesive, fixing in opening as per Specifications and Drawings shown in MES Schedule Part-II, complete all as specified and as directed.

S&F 35 mm thick factory made flush shutter, solid core construction with block board core and ply wood face panels, commercial type on both side, complete all as specified & directed.

S&F 2nd class hard wood shutter 35mm thick plain framed, panalled shutter (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part-I), kiln seasoned and chemically pressure treated.complete all as specified & directed.

S&F 2nd class hardwood 35mm thick glazed and skeleton shutters open rebated and prepared to receive glass gauge etc. Divided into squares with plain chamfered or rounded, rebated sash bars, sizes of the members of the shutters as specified in SSR Part I, section 8, clause 8.23(a).complete all as specified & directed.

S&F 300 mm Aluminium alloy anodised sliding door bolt, plate type and fixing clip of sheet cast of extruded section and fixing bolt and sliding bolt of extruded section and fixed in position.complete all as specified & directed.

S&F 200 mm aluminium anodised barrel tower bolt, of extruded section and fixed in position.complete all as specified & directed.

M&L for extruded aluminium alloy handle fabricated type of 150 mm long.complete all as specified & directed.

S&F 100 mm Butt hinges medium weight cold rolled mild steel and fixed.complete all as specified & directed.

S&F for MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate .complete all as specified & directed.

M&L Water Proofing Treatment on existing cleaned RCC Roof with the following Specifications and Manufacturer's instructions, complete all as specified and as directed :- (a) Preparing and cleaning of fully dry surface as per IS:3067-1966. (b) Applying Bitumen Primer conforming to IS-3384-1986 over the Cleaned Plastered Surface @ 0.50 Litre per Sqm. (c) Applying a layer of APP based Polymeric Membrance; 3.0mm thick (minimum) weighing 3.60 Kilogram per Square Metre (reinforced) with Polyster Non Woven Fabric weighing not less than 160 Grams per Square Metre by Torch application. The overlaps shall be minimum 100mm on the Transverse direction and 75mm on Longitudinal direction. (d) Applying one coat of Aluminium Paint @ 0.10 Litre per Sqm over APP based Polymeric Membrane.

M&L for 15 mm thick screed bed in cm 1:3 mixed with WPC as per manufactures instruction finished even and smooth over RCC roof slab without using extra cement (WPC shall be measured seperately).complete all as specified & directed.

S&F pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/clading to wall, fixed with self tapping screws complete all as specified & directed.

S&F pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in ridges, roof covering/clading to wall, fixed with self tapping screws complete all as specified & directed.

M&L False ceiling with aluminium powder coated snap grid of size 600 mm x 600 mm to support the boards/files with aluminium anodised main 'T' section 36mm x 25mm x 1.40mm cross tee 23.50mm x 23.50mm x 1.40mm thick and aluminium angle 25mm x 25mm x 1.40mm as on edges/sides including hanging arrangements with 1.6mm dia GI wire and anodised adjuster and applying two coats of oil bound distemper over a coat of alkali resistant primer on exposed surfaces complete all as specified and as directed.

M & L 4mm thick non asbestos fibre cement building board fixed/inserted to Aluminium frame work, as in ceiling complete all as specified and as directed.

M & L applying two coat of distemper on ceilling non asbestos fibre cement building board surfaces , complete all as specified and as directed.

S&F Vitreous China White Squatting Pan ‘ORISSA’ Pattern, size 580x440mm with ‘P’ or ‘S’ Trap, Integral Foot Rest, providing Joints between Flush Pipe and Socket of WC Pan including Flushing Cistern and Flush Pipe, fixing with and including provision of cement Concrete Bedding including Taking out/ down unserviceable WC Pan and connected Items, complete all as specified and as directed.

S&F White PVC Flushing Cistern 10 Litre capacity, Low Level Valve Less, Syphonic Action type with Inlet, Ball Valve, Float and Handle including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 and fixed including taking down/out unserviceable Flushing Cistern and connected Items, complete all as specified and as directed.

S&F Vitreous China Wash Hand Basin 550x400mm in size, White (Flat Back or Angle Back Type) with 32mm dia Brass Chromium Plated Waste Fitting, a pair of Cast Iron Brackets duly painted including Cutting and pinning in Ends, making good disturbed Surfaces in Cement Mortar 1:3 including taking down/out unserviceable Wash Hand Basin and connected Items, complete all as specified and as directed.

S&F Rotational Moulded Polyethylene (HDPE) Water Storage Tank 1000 Litre Capacity (Cylindrical Vertical with Closed Top), Black in Colour, Three Layered Construction, hoisted and fixed in Position all specified in MES Schedule Part-I including provision of 25mm x 100mm GI nippples with check nuts for inlet, outlet wash and overflow pipe including Lowering of old/unserviceable Water Storage Tank of any description, complete all as specified and as directed.

S&F PTMT Ball Valve 20mm dia having mini -mum weight 210 Grams, high pressure with epoxy coated Aluminium Rod and high density Plastic Ball, screwed for Iron Pipe and fixed as in repair, complete all as specified and as directed.

S & F for 40 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Supply and fixing 25 mm bore gate valve cast copper alloy screwed down high pressure with clutch handle screwed both ends for Iron pipe complete all as directed.

S & F for 20 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

S & F for 15 mm Gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed

S & F Towel Rail 600mm long of chromium plated brass metal fixed with and including Chromium plated brass screws and wooden/plastic cleats complete all as specified and directed'

S&F Grating doom 100mm dia of PTMT (Minimum weight 25gms) complete all as specified and directed'

S&F Swivel Shower Rose with Arms of Chromium Plated for fixing with 15mm bore (dia) Pipe and fixed-in-repairs, complete all as specified and as directed.

S&F Angular Stop Cock 15 mm dia (bore), cast copper alloy, fancy type, chromium plated, screwed down, high pressure,with wall flange screwed for Iron Pipes or Brass Ferrule and fixed, complete all as specified and directed.

S&F Bib Tap 15mm dia (bore), Cast Copper Alloy, Chromium Plated, screwed down high pressure with Crutch or Butterfly Handle, screwed both Ends for Iron Pipe or for Unions and fixed-in-repairs, complete all as specified and directed.

S&F Pillar taps, cast copper alloy , with capstan heads, fancy tupe, chromium plated , screwed down high pressure, with long screwed shanks and fly nuts, screwed for iron pipe , and fixed complete all as specified and directed.

Supply and Laying Steel Water Tubing 15mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, complete as all specified and as directed.

Supply and Laying Steel Water Tubing 20mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, complete as all specified and as directed.

Supply and Laying Steel Water Tubing 25mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, complete as all specified and as directed.

Supply and Laying Steel Water Tubing 40mm Bore (dia), Galvanised, ‘Medium Grade’ with all Fittings, fixed on Walls, Ceiling or laid in Floors or any other Situation, complete as all specified and as directed.

S&F PVC (SWR) Soil, Waste and Ventilating Pipe 110mm bore (dia), single socketed, in any length with Rubber Ring Joints fixed to Walls, complete all as specified and as directed.

S&F PVC (SWR) Soil, Waste and Ventilating Pipe 75mm bore (dia), single socketed, in any length with Rubber Ring Joints fixed to Walls, complete all as specified and as directed.

S&F PVC (SWR) Bend 75mm bore (dia), any type, equal or unequal with Access Door, etc. and Jointing with Solvent Cement, complete all as specified and as directed.

S&F PVC (SWR) Bend 110mm bore (dia), any type, equal or unequal with Access Door, etc. and Jointing with Solvent Cement, complete all as specified and as directed.

Material and labour point wiring for one light/fan/exhaust fan point controlled by one, one way switch using 1.5 sqmm nominal cross sectional area multistranded copper conductor ,PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings of medium grade, including metal flush box suitable for modular cover plate with frame of suitable size 1 M to 8 M and 1.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLSH PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed. (Rate deemed to be inclusive of cutting chases and making good disturbed surface).

All as per item No.110 above but One 3 pin 5 Amps socket out let points on independent board complete all as specified and directed by Engineer-in-charge.

All as per item No.110 above but 5 Amp socket on same board with other switches.complete all as specified and directed by Engineer-in-charge.

M&L for point wiring for socket out let on 16 Amps independent Boards controlled by one, one way switch using 2.5 sqmm nominal cross sectional area multistranded copper conductor, PVC insulated unsheathed FRLSH cables in and including 20 mm dia or higher size PVC concealed conduits and fittings, including metal flush box suitable for modular cover plate with frame of suitable size of 3M and 2.5 sqmm nominal cross sectioanl area multistranded copper conductor FRLSH PVC insulated unsheathed earth wire and connecting to earth dolly and brass screws, washers etc. complete all as specified and directed. (Rate deemed to be inclusive of cutting chases and making good disturbed surface).

S&F Modular type switch 6 Amps 230V AC single module one way complete all as specified and as directed.

S&F Modular socket out let 2 in 1 ,3 pin 10 Amps shuttered type 230V AC 2 module complete all as specified and as directed.

S&F Modular socket out let 2 in 1 ,3 pin 16 Amps shuttered type 230V AC 2 module complete all as specified and as directed.

S&F Modular type switch 16 Amps 230V AC single module one way complete all as specified and as directed.

S&F Modular type fan regulator Step type ,100 Watt, one module, 230V AC complete all as specified and as directed.

Supply & fixed ceiling rose surface bakelite 65 mm x 50 mm two to three terminal suitable for 230 Volts AC 6 Amps complete all as specified and as directed.

Supply & fixing lamp holder, PVC/polycarbonate type with back plate straight or angular suitable for batten fittings complete all as specified and as directed.

Supply and fixing modular white cover plate with frame 2 modules complete all as specified and as directed.

Supply and fixing modular white cover plate with frame 3 modules complete all as specified and as directed.

Supply and fixing modular white cover plate with frame 4 modules complete all as specified and as directed.

Supply and fixing modular white cover plate with frame 6 modules complete all as specified and as directed.

Supply and fixing modular white cover plate with frame 8 modules complete all as specified and as directed.

Supply and fixing modular metal flush box 2 modules complete all as specified and as directed.

Supply and fixing modular metal flush box 3 modules complete all as specified and as directed.

Supply and fixing modular metal flush box 4 modules complete all as specified and as directed.

Supply and fixing modular metal flush box 6 modules complete all as specified and as directed.

Supply and fixing modular metal flush box 8 modules complete all as specified and as directed.

Supply and fixing18 W LED light fitting wall mounted batten 4'ft , minimumm lumen output 100 lumen/Wat, extruded polycarbonate, enivromental friendly, heat sink provided for efficent heat dissipation and integrated electronic driver for 18 watt,6500K including necessary connection complete all as specified and directed.

Supply and fixing security light fittings 30 watts, minimumm lumen output 100 lumen/Watt, made up of pressure dia cast housing with prismatic polycarbornate diffuser and individual LED with secondary optic and IP65 including necessary connection complete including 25mm dia light grade GI bracket with nut bolt and clamp complete with all accessories including connected with twin core twisted flexible copper conductor of suitable size complete all as specified and as directed.

Supply and fixing LED not less than 8W, 5700 K, 0.6 M long LED bollard for pathways and gardens are made with aluminium extrusion for sturdiness and better finish, UV stabilized injuction moulded oval polycarbonate diffuser for spot-free lighting and IP 65 degree of protection with fixing accessories complete as per manufacturer's instructions including PCC 1:3:6 (1 ft) complete all as specified and as directed.

Supply and fixing epoxy powder coated sheet metal enclosure for DBs, double door (when MCBs to be used), Single pole and neutral 240 V, 8 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as specified and as directed.

Supply and fixing epoxy powder coated sheet metal enclosure for DBs, double door , Single pole and neutral 240 V, 4 ways with mounting fitted with bus bar, DIN channel , neutral link and incoming contact complete all as specified and as directed.

Supply and fixing MCB SP, 6 to 32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs including necessry connection complete all as specified and directed.

Supply and fixing MCB SPN 6-32 Amps, 'C' series 10kA, 240 Volts and to be housed in DBs complete including necessry connection all as specified and directed.

Material and labour for earthing complete with galvanised mild steel earth plate electrode 600x600x6.0mm thick, burried directly in ground to a depth not less than 2.25 metres deep below ground level with top edge of earth plate not less than 1.5 metre below normal ground level surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness of 15 cm all around the plate, using GI wire 4 mm dia as earth strip electrode bolted or rivetted to earth plate at one end and connected to equipments at another end, GI earth strip encased in and including 40 mm dia GI 'light grade' pipe from upper end of earth plate upto equipments,20 dia bore GI pipe 'light grade' as water pipe from earth chamber to upper edge of earth plate, Test point , GI funnel with wire mesh fixed on water pipe and PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in pit chamber and RCC pit cover 50mm thick precast RCC 1:2:4 type B-1, duly reinforced with MS round bars 6mm dia @ 100 c/c both ways with 10mm dia MS round bar as in lifting handles, excavation, earth work including laying the GI pipe concealed in floor/wall all as described in electric plate of SSR Part I complete all as specified and directed and testing on completion.

S&F Brushless DC (BLDC) ceiling fan 1200mm sweep maximum 26W with operating voltage 140v-240v AC 50 Hz, Max -360RPM, white colour without remote control operated,5 star energy saving rating (minimum 5 Year warranty) complete all as specified and as directed.

S & F ventilating matallic exhaust fan 300 mm sweep 230 volt AC complete with louver and all accessories including cutting hole of suitable size, making good surface with plaster in CM (1:6) and applying two coat of distemper complete with fixing arrangement to wall connected with twin core twisted flexible copper conductor (23/.0076) of suitable size complete all as specified and as directed.

Supply, laying / fixing / connecting, testing and commissioning of 10 Sqmm x 2 core LT under ground cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cable (heavy duty) with multistranded aluminium conductor,1100 Volts grade in trenches/on wall/poles laid in ducts/inside protection pipe of the following cross sectional area including cable glands,lugs and suitable size of MS saddle clips (where ever cable laid in ceilings / walls without cable duct) all as directed by the Engr-in-Charge for the following ratings Note:- (i) Excavation,sand cushioning,brick will be measured and paid separtely.

Supply, laying / fixing / connecting, testing and commissioning of 6 Sqmm x 2.0 core LT under ground cable XLPE insulated, screened, PVC bedded, galvanised steel strip or wire armoured, electric cable (heavy duty) with multistranded aluminium conductor,1100 Volts grade in trenches/on wall/poles laid in ducts/inside protection pipe of the following cross sectional area including cable glands,lugs and suitable size of MS saddle clips (where ever cable laid in ceilings / walls without cable duct) all as directed by the Engr-in-Charge for the following ratings Note:- (i) Excavation,sand cushioning,brick will be measured and paid separtely.

Supply and laying dry coarse sand as in cushioning of under ground electric cable in trenches, laid to a uniform thickness of 23 Cm (15 Cm under the cable & 8 Cm over the cable) and gently punned down to 18 Cm thickness complete all as specified and as directed by the Engr-in-Charge. Note:- Thickness after punning down shall be measured for payment.

Supply and lay in trenches fly ash bricks, for cable protection all as specified and directed by the Engr-in-Charge.

S&F Pipes galvanized, 50 mm bore “light grade”, supplied and laid complete including necessary fittings such as tees, bends, elbows, sockets, reducers etc as per site requirement complete all as specified and as directed. Note 1:-The contract sum shall be arrived at after deducting amount of schedule of credit from the total quoted amount. Note 2-Contractor's supervisor and main worker would wear shirt/T-shirt of colour sky blue/brown/yellow preferable embossed with contractor's firm name while carrying out any activities in defence area for better check of security purpose. Note 3:-The tenderer (all eligible contractors) shall ascertain the taxes & levies as on date. The subject tender caters all the taxes & levies as on date including the latest notification of GST issued as on date ( issued by Central Board of Indirect Taxes and Customs)

M/S Jiban Krishan Das and Co

D G Corporation

M/s MN ENTERPRISRE

M/S Sharma Construction