Loading…
India Infra Updates on WhatsApp
Join the Tenderkart WhatsApp channel for India Tender Updates
Loading…
Tender ID
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
Tender Value
₹55.3 Cr
EMD Value
₹55.3 L
Closing Date
26 Dec 2023, 11:00 amClosed
Eligibility, documents, scope and key termsEligibility, required documents, scope of work and key terms of this tender, in one click.
NBCC Bhawan
NBCC Bhawan
Construction of Teaching Block-III at Chaudhary Ranbir Singh University, Jind, Haryana
NBCC/CPG/CRSU/Jind/2023/386~EWb014b8d190a4a5661f2beda9
NBCC/CPG/CRSU/Jind/2023/386
Open Tender-Domestic
Civil Works General
NBCC Bhawan
₹1.2 L
₹55.3 L
26 Dec 2023
10 Nov 2023
26 Dec 2023
10 Nov 2023
26 Dec 2023
1 CIVIL WORK 3074,48,125.00 304,80,556.00 3379,28,681.00
2 P.H. WORK 68,63,721.00 23,72,362.00 92,36,083.00
3 ROAD WORK 43,14,872.00 3,58,133.00 46,73,005.00
4 RAIN WATER HARVESTING 12,40,310.00 12,40,310.00
5 WATER SUPPLY WITH SHALLOW TUBEWELL 3,33,212.00 3,33,212.00
6 FURNITURE COMPONENT 96,43,219.00 96,43,219.00
7 Amount as per Schedule-1 (E.I) HSR Items 170,09,674.00 170,09,674.00
8 Amount as per Schedule-2 (Fans & Fittings) 278,75,838.00 278,75,838.00
9 Amount as per Schedule-3 (LIFT) 103,29,090.00 103,29,090.00
10 Amount as per Schedule-3 (PA SYSTEM) 12,31,108.00 12,31,108.00
11 Amount as per Schedule-5 (FIRE ALARM SYSTEM) 41,51,950.00 41,51,950.00
12 Amount as per Schedule-6 (HVAC SYSTEM) 378,87,341.00 378,87,341.00
13 Amount as per Schedule-7 (FIRE HYDRANT SYSTEM) 70,79,519.00 70,79,519.00
SUB TOTAL (A) Rs. 3372,09,914.00 1314,09,116.00 4686,19,030.00
Add Prevailing GST @ 18% (HSR + NS) on (A) 606,97,784.52 236,53,640.88 843,51,425.40
SUB TOTAL (B) Rs. 3979,07,698.52 1550,62,756.88 5529,70,455.40
(ESTIMATED COST PUT TO TENDER, SAY RS. ) 5529.70 Lacs
Authorised Signatory Contractor BOQ Page No. 1 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
DETAILED ESTIMATE FOR CONSTRUCTION OF TEACHING BLOCK - 3 AT CRSU, JIND, HARYANA
( CIVIL WORK )
Sr. Description of Item
HSR No. Qty. Unit Rate w/o GST Amount
(A) CIVIL WORK - AS PER HSR 2021
Earth work in excavation by mechanical means (Hydraulic excavator)/manual means
HSR-21 over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan)
4.12 including getting out and disposal of excavated earth lead up to 50 m and lift up to 1.5 m,
as directed by Engineer-in-charge.
4.12.1 All kinds of soil 9,118.87 Cum 77.691 7,08,454.00
HSR-21 Filling available excavated earth (excluding rock) in trenches, plinth, sides of
2 foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited 5,494.56 Cum 46.436 2,55,145.00
layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
Providing and injecting chemical emulsion for PRE- CONSTRUCTIONAL anti
termite treatment and creating a chemical barrier under and around the column pits,
HSR-21 wall trenches, basement excavation, top surface of plinth filing junction of wall and floor,
4.39 along with the external perimetre of building, expansion joints surrounding of pipes and
conduit etc, complete (plinth area of the building at ground floor only shall be measured)
using Chlorpyriphos/ Lindane emulsifiable concentrate of 20%.
HSR-21 Providing and laying in position cement concrete of specified grade excluding the
6.1 cost of centering and shuttering - All work below plinth level and up to Floor IV level:
1 :4: 8 ( 1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm
nominal size).
1:5:10 (1 cement : 5 coarse sand (zone-III): 10 graded stone aggregate 40 mm
nominal size).
Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3
HSR-21 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of
6.13 dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with
fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.
Providing and laying in position machine batched and machine mixed design mix
M-25 grade cement concrete for reinforced cement concrete work, using cement
content as per approved design mix, including pumping of concrete to site of laying but
excluding the cost of centering, shuttering, finishing and reinforcement, including
HSR-21 admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of
6.25 concrete, improve workability without impairing strength and durability as per direction of
Engineer-in-charge.
(Note :- Cement content considered in this item is @ 330 kg/cum. Less cement used as
per design mix is recoverable. However no extra payment shall be made if excess cement
Allused asup
works pertodesign
plinthmix).
level. 3,591.51 Cum 4,464.107 160,32,883.00
6.25.2 All works above plinth level up to floor IV level 6,182.55 Cum 4,501.613 278,31,431.00
Extra for providing richer mixes up to plinth and at all floor levels.
7 (Note :- Less cement used as per design mix is recoverable. However no extra payment
shall be made if excess cement is used as per design mix).
Providing M-35 grade concrete instead of M-25 cum grade BMC/ RMC. (Note:-
Cement content considered in M-30 is @ 350 kg/cum)
HSR-21 Extra for R.C.C./ B.M.C/ R.M.C. work above floor IV level for each three floors or
6.27 part thereof.
(a) Above Floor IV to Floor VII 2,951.04 Cum 243.789 7,19,432.00
Authorised Signatory Contractor BOQ Page No. 2 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
(b) Above Floor VII to Floor X 274.07 Cum 487.578 1,33,630.00
HSR-21 Centering and shuttering including strutting, propping etc. and removal of form
6.30.1 Foundations, footings, bases of columns, etc. for mass concrete. 419.10 Sqm 156.275 65,495.00
Walls (any thickness) including attached pilasters,buttresses, plinth and string courses
6.30.3 Suspended floors, roofs, landings, balconies. 17,503.15 Sqm 208.069 36,41,862.00
6.30.4 Shelves (Cast in situ). 592.20 Sqm 223.250 1,32,208.00
6.30.5 Lintels, beams, plinth beams, girders, bressumers and cantilever. 16,985.57 Sqm 296.476 50,35,815.00
6.30.6 Columns, Pillars, Piers, Abutments, Posts and Struts. 7,069.94 Sqm 261.649 18,49,844.00
6.30.7 Stairs, (excluding landings) except spiral-staircases. 399.06 Sqm 290.225 1,15,817.00
Vertical and horizontal fins individually or forming box louvers band, facias and eaves
boards.
Extra for shuttering in circular work (20% of respective centering and shuttering
items. ( For Circular Column)
Edges of slabs and breaks in floors and walls.
Under 20 cm wide.
6.30.19 Weather shade, Chajjas, corbels etc., including edges. 698.81 Sqm 277.723 1,94,074.00
Extra for additional height in centering, shuttering where ever required with
HSR-21 adequate bracing, propping etc., including cost of de-shuttering and decentring at all
6.32 levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof
(Plan area to be measured).
6.32.1 Suspended floors, roofs, landing, beams and balconies (Plan area to be measured) 17,902.21 Sqm 146.452 26,21,814.00
Steel reinforcement for R.C.C. work, where not included in the complete rate of
RCC, including straightening, cutting, bending, placing in position, binding, wastage,
overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc.
complete in all respect below plinth level.
11 Note:- Reinforcement shall be measured in length including hooks, if any, separately for
different diameters as actually used in work , excluding overlaps. Wastage, overlaps,
couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or
other methods of binding & placing shall not be measured and cost of these items shall be
deemed to be included in the rates for reinforcement.
Thermo-Mechanically Treated bars of grade Fe-500D or more.
(Note: - TMT FE-550D bars to be used.)
Steel reinforcement for R.C.C. work, where not included in the complete rate of
RCC, including straightening, cutting, bending, placing in position, binding, wastage,
overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc.
complete in all respect above plinth level.
12 Note:- Reinforcement shall be measured in length including hooks, if any, separately for
different diameters as actually used in work , excluding overlaps. Wastage, overlaps,
couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or
other methods of binding & placing shall not be measured and cost of these items shall be
deemed to be included in the rates for reinforcement.
Thermo-Mechanically Treated bars of grade Fe-500D or more.
(Note: - TMT FE-550D bars to be used.)
HSR-21 Providing and fixing in position Stainless steel Grade 304 plate-1.0 mm thick as
6.60 per design for expansion joints.
6.60.1 200 mm wide. 357.00 Rmt 555.446 1,98,294.00
Authorised Signatory Contractor BOQ Page No. 3 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Providing and fixing of expansion joint system related with floor location as per
drawings and direction of Engineer-In-Charge. The joints system will be of extruded
aluminium base members, self aligning/ self centering arrangement and support plates
etc. as per ASTM 9221-02. The system shall be such that it provides floor to floor /floor to
wall expansion control system for various vertical location in load application areas that
accommodates multi directional seismic movement without stress to it's components.
System shall consist of metal profiles with a universal aluminium base member designed
to accommodate various project conditions and finish floor treatments. The cover plate
14 shall be designed of width and thickness required to satisfy projects movement and
loading requirements and secured to base members by utilizing manufacturer's pre-
engineered self centering arrangement that freely rotates I moves in all directions. The
Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside
the corresponding aluminium extrusion cavity to allow freedom of movement and flexure
in all directions including vertical displacement. Provision of Moisture Barrier Membrane in
the Joint System to have watertight joint is mandatory requirement all as per the
manufactures design and as approved by Engineer -in-Charge. (Material shall confirm to
6.61.1 Floor Joint of 100 mm gap 357.00 Rmt 4,472.144 15,96,555.00
Providing and fixing of expansion joint system of approved make and
manufactures for various roof locations as per approved drawings and direction of
Engineer-In-Charge. The joints shall be of extruded aluminium base members with, self
aligning and self centering arrangement support plates as per ASTM B221-02. The system
shall be such that it provides watertight roof to roof/roof to corner joint cover expansion
HSR-21 control system that is capable of accommodating multidirectional seismic movement
6.63 without stress to its components. System shall consist of metal profile that incorporates a
universal aluminium base member designed to accommodate various project conditions
and roof treatments. The cover plate shall be designed of width and thickness required to
satisfy movement and loading requirements and secured to base members by utilizing
manufacturer's preengineered self-centering arrangement that freely rotates I moves in
all directions.
The Self centering arrangement shall exhibit circular sphere ends that lock and slide
inside the corresponding aluminium extrusion cavity to allow freedom of movement and
flexure in all directions including vertical displacement. The Joint System shall resists
damage or deterioration from the impact of falling ice, exposure to UV, airborne
contaminants and occasional foot traffic from maintenance personnel. Provision of
Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory
requirement. (Material shall confirm to ASTM 6063).
6.63.1 Roof Joint of 100 mm gap 59.50 Rmt 4,123.874 2,45,371.00
HSR-21 Brick work with common burnt clay non-modular bricks of class designation 10.5 in
7.21 foundation and plinth in:.
7.21.2 Cement mortar 1:6 (1 cement: 6 coarse sand). 383.05 Cum 3,531.815 13,52,853.00
HSR-21 Brick work with common burnt clay non-modular bricks of class designation 10.5 in
7.22 superstructure above plinth level up to floor IV level in all shapes and sizes in :
7.22.2 Cement mortar 1:6 (1 cement: 6 coarse sand) 1,628.29 Cum 3,961.348 64,50,221.00
Authorised Signatory Contractor BOQ Page No. 4 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
HSR-21 Extra for Brick work with common burnt clay non-modular bricks / non modular
18 Note-10 of fly ash bricks in superstructure above floor IV level, for each three additional floor
Ch. 7 above floor IV level or part thereof by mechanical means.
(a) Above Floor IV to Floor VII 1,325.58 Cum 35.318 46,817.00
(b) Above Floor VII to Floor X 70.01 Cum 70.636 4,945.00
HSR-21 Half brick masonry with common burnt clay non-modular bricks of class designation
7.28 10.5 in superstructure above plinth level up to floor IV level.
7.28.2 Cement mortar 1 :4 ( 1 cement :4 coarse sand) 4,750.64 Sqm 487.578 23,16,307.00
HSR-21 Extra for half brick masonry in superstructure, above floor IV level for every three
7.29 floors or part thereof by mechanical means.
(a) Above Floor IV to Floor VII 4,024.96 Sqm 17.860 71,886.00
(b) Above Floor VII to Floor X 61.68 Sqm 35.720 2,203.00
HSR-21 Half brick masonry with non modular fly ash bricks of class designation 10,
7.31 conforming IS :12894, in super structure above plinth and up to floor IV level.
7.31.2 Cement mortar 1 :4 ( 1 cement :4 coarse sand) 3,167.09 Sqm 474.183 15,01,782.00
HSR-21 Honey-comb brick work 10/11.4 cm thick with common burnt clay bricks of class
22 designation 10.5 in super structure above plinth level up to floor IV level with cement 81.77 Sqm 326.838 26,724.00
mortar 1 :4 (1 cement : 4 coarse sand).
HSR-21 Brick work with non modular fly ash bricks conforming to IS :12894, class
23 designation 10 average compressive strength in super structure above plinth level up
to floor IV level in :
7.47.2 Cement mortar 1:6 (1 cement: 6 Coarse sand). 1,085.53 Cum 3,441.622 37,35,971.00
Providing and fixing horizontal chajja of stone 40 mm thick and up to 80 cm
HSR-21 projection in cement mortar 1 :4 (1 cement : 4 coarse sand), including pointing in white
7.96 cement mortar 1 :2 (1 white cement : 2 stone dust) with an admixture of pigment
matching the stone shade :
7.96.1 Red Sand Stone 173.88 Sqm 417.924 72,669.00
Providing and fixing Red Sand Stone dry cladding upto 10 m height with 30 mm
thick gang saw cut stone with (machine cut edges) of uniform colour and size upto
HSR-21 1mx1m, fixed to structural steel frame work and/ or with the help of cramps, pins etc.
8.1 and sealing the joints with approved weather sealant including scaffolding work as per
Architectural drawing and direction of Engineer-in-charge.(The steel frame work,
stainless steel cramps and pins etc. shall be paid for separately).
8.1.1 Red Sand Stone - 30mm thick gang saw cut stone 2,976.39 Sqm 1,005.518 29,92,814.00
Authorised Signatory Contractor BOQ Page No. 5 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Providing and fixing structural steel frame (for dry cladding with 30 mm thick
gang saw cut with machine cut edges sand stone) on walls at all heights using M.S.
square/ rectangular tube in the required pattern as per architectural drawing, including
cost of cutting, bending, welding etc. The frame work shall be fixed to the wall with the
help of M.S. brackets/ lugs of angle iron/ flats etc. which shall be welded to the frame and
embedded in brick wall with cement concrete block 1 :2:4 (1 cement :2 coarse sand :4
graded stone aggregate 20 mm nominal size) of size 300x230x300 mm, including cost of
HSR-21 necessary centring and shuttering and with approved expansion hold fasteners on
8.2 CC/RCC surface, including drilling necessary holes. Approved cramps/ pins etc. shall be
welded to the frame work to support stone cladding, the steel work will be given a
priming coat of Zinc primer as approved by Engineer-in-charge and painted with two or
more coats of epoxy paint (Shop drawings shall be submitted by the contractor to the
Engineer-in-charge for approval before execution). The frame work shall be fixed in true
horizontal & vertical lines/planes. (Only structural steel frame work shall be measured for
the purpose of payment, stainless steel cramps shall be paid for separately and nothing
extra shall be paid).
Providing and fixing adjustable stainless steel cramps of approved quality, required
shape and size, adjustable with stainless steel nuts, bolts and washer (total weight not
27 less than 260 gms), for dry stone cladding fixed on frame work at suitable location, 22,138.00 Each 217.892 48,23,693.00
including making necessary recesses in stone slab, drilling required holes etc complete as
per direction of the Engineer-in-charge.
HSR-21 Extra for stone work for wall lining on exterior walls of height more than 10 m from
8.14 ground level for every additional height of 3 m or part there of.
(a) Above 10m but Upto 13m 285.70 Sqm 53.580 15,308.00
(b) Above 13m but Upto 16m 352.74 Sqm 107.160 37,800.00
(c) Above 16m but Upto 19m 359.94 Sqm 160.740 57,857.00
(d) Above 19m but Upto 22m 340.50 Sqm 214.320 72,976.00
(e) Above 22m but Upto 25m 309.54 Sqm 267.900 82,926.00
(f) Above 25m but Upto 28m 157.01 Sqm 321.480 50,476.00
Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded
and prepolished, machine cut for kitchen platforms, vanity counters, window sills,
HSR-21 facias and similar locations of required size, approved shade, colour and texture laid over
8.26 20 mm thick base cement mortar 1 :4 (1 cement : 4 coarse sand), joints treated with
white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing,
moulding and polishing to edges to give high gloss finish etc. complete at all levels.
Granite of any colour and shade.
1. Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.)
2. Colour/Shade to be approved by the University
8.26.2.1 Area of slab upto 0.50 sqm 241.07 Sqm 2,750.440 6,63,055.00
8.26.2.2 Area of slab over 0.50 sqm 1,457.68 Sqm 2,776.337 40,47,005.00
Providing edge moulding to 18 mm thick marble stone counters, Vanities etc.,
30 including machine polishing to edge to give high gloss finish etc. complete as per design
approved by Engineer-in-Charge.
8.27.2 Granite Work 6,037.10 Rmt 229.501 13,85,520.00
Authorised Signatory Contractor BOQ Page No. 6 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Providing and fixing false ceiling at all height including providing and fixing of frame
work made of special sections, power pressed from M.S. sheets and galvanized with zinc
coating of 120 gms/sqm (both side inclusive) as per IS: 277 and consisting of angle cleats
of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm
centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm
long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50
mm of required length with nuts & bolts of required size and other end of angle hanger
fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm
centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with
tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall
be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips
31 made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing
perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long,
the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm
centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum
board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5
x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and
square edges of the board with recommended jointing compound , jointing tapes ,
finishing with jointing compound in 3 layers covering up to 150 mm on both sides of joint
and two coats of primer suitable for board, all as per manufacturer's specification and also
including the cost of making openings for light fittings, grills, diffusers, cut outs made with
frame of perimeter channels suitably fixed, all complete as per drawings, specification and
direction of the Engineer in Charge but excluding the cost of painting with :
12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I)
:2011 (Board with BIS certification marks).
Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in
true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel
sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T"
runner with suitably spaced joints to get required length and of size 24x38 mm made
from 0.30 mm thick (minimum) sheet, spaced at 1200 mm centre to centre and cross 'T'
of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced
between main "T" at 600 mm centre to centre to form a grid of 1200x600 mm and
secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick
HSR-21 (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of
9.47 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of
approved texture in the grid including, required cutting/making, opening for services like
diffusers, grills, light fittings, fixtures, smoke detectors etc. Main 'T' runners to be
suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1 .6 mm fixed to
ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with
galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm centre to
centre along main T, bottom exposed width of 24 mm of all T-sections shall be pre-
painted with polyester paint, all complete for all heights as per specifications, drawings
and as directed by Engineer-in-charge.
Authorised Signatory Contractor BOQ Page No. 7 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
GI Metal Ceiling Lay in perforated Tegular edge global white colour tiles of size
595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of
100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and
having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder
coated of thickness 60 microns (minimum), including factory painted after bending and
perforation, and backed with a black Glass fibre acoustical fleece.
Providing and fixing to the inlet mouth of rain water pipe PTMT (an Engineering
33 Thermoplastic) grating square (Slit) 150 mm square with a height of 8 mm and weighing 34.00 Each 81.263 2,763.00
not less than 100 gms.
HSR-21 Supplying and providing of Tangri River Sand under floors Including watering and
10.3 compaction in 25cm layers, dressing etc. complete In all respects (As per item 10.2)
Providing and fixing of Kota stone slab flooring over 20 mm (average) thick base
laid over and jointed with grey cement slurry mixed with pigment to match the shade of
34 the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 ( 1
cement : 4 coarse sand) as per approved pattern shown in the drawing.
(Note: Kota stone of 1st Quality (Ratia Variety) of uniform color shall to be used.)
10.37.1 25 mm thick 3,538.48 Sqm 790.305 27,96,478.00
Providing and fixing of Kota stone slabs 20 mm thick in risers of steps, skirting,
dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1skirting, dado and
HSR-21 pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and
10.38 jointed with grey cement slurry mixed with pigment to match the shade of the slabs,
including rubbing and polishing complete as per approved pattern shown in the drawing.
(Note: Kota stone of 1st Quality (Ratia Variety) of uniform color shall to be used.)
Providing and fixing of marble stone flooring with 16 mm thick marble stone, as per
HSR-21 sample of marble approved by Engineer-in-charge, over 20 mm (average) thick base of
10.44 cement mortar 1 :4 (1 cement : 4 coarse sand) laid and jointed with grey cement slurry,
including rubbing and polishing complete with:
10.44.3 Agaria White 884.62 Sqm 1,833.329 16,21,799.00
Providing and laying Flamed finish Granite stone flooring in required design and
patterns, in linear as well as curvilinear portions of the building all complete as per the
architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of
37 cement mortar 1 :4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and
pointing with white cement slurry admixed with pigment of matching shade including
rubbing , curing and polishing etc. all complete as specified and as directed by the
Engineer-in-Charge.
Flamed finish Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or
10.49.1 equivalent. 67.89 Sqm 1,759.210 1,19,437.00
(Note:- Colour/Shade to be approved by the University)
Authorised Signatory Contractor BOQ Page No. 8 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Providing and laying Polished Granite stone flooring in required design and
patterns, in linear as well as curvilinear portions of the building all complete as per the
architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of
38 cement mortar 1 :4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and
pointing with white cement slurry admixed with pigment of matching shade including
rubbing , curing and polishing etc. all complete as specified and as directed by the
Engineer-in-Charge.
Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.
(Note:- Colour/Shade to be approved by the University)
Providing and fixing granite stone in all shades 15mm to 18 mm thick in sqm
skirting /dado, risers of steps, pillars and wall facing, laid in any pattern as specified
over base of 12mm thick cement coarse sand mortar 1 :3 and jointed with white cement
HSR-21 slurry mixed with pigment to match the shade of Granite including labour for fixing
10.51 cramps pins and dowels etc.
1. Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.)
2. Colour/Shade to be approved by the University
Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS : 15622
(thickness to be specified by the manufacturer ) of approved make in all colours, shades
except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in
40 skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1 :3 (1 2,185.46 Sqm 538.479 11,76,823.00
cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including
pointing in white cement mixed with pigment of matching shade complete.
Note:- Wall Tiles of Size 300 x 450mm shall be used.
Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or
more (thickness to be specified by the manufacturer), of 1st quality conforming to IS :
15622, of approved make, in colours White, Ivory, Grey, Fume Red Brown, laid on 20 mm
41 thick cement mortar 1 :4 (1 Cement: 4 Coarse sand), jointing with grey cement slurry @ 93.98 Sqm 684.931 64,372.00
3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc.,
complete.
Note:- In toilets Antiskid Ceramic tiles shall be used.
Providing and laying vitrified floor tiles in different sizes (thickness to be specified
by the manufacturer) with water absorption less than 0.08% and conforming to IS:
HSR-21 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1
10.63 :4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including
grouting the joints with white cement and matching pigments etc., complete.
(Note:- Double charged Vitrified tiles shall be used.)
10.63.2 Size of Tile 600 x 600 mm. 777.51 Sqm 986.765 7,67,220.00
10.63.3 Size of Tile 800 x800 mm. 2,821.66 Sqm 1,164.472 32,85,747.00
Authorised Signatory Contractor BOQ Page No. 9 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Providing and laying Vitrified tiles in different sizes (thickness to be specified by
manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of
approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed
43 of cement mortar 1 :3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3
kg/ sqm including grouting the joint with white cement & matching pigments etc.
complete.
Note:- Double charged Vitrified tiles shall be used.
10.67.2 Size of Tile 600 x 600 mm. 4,237.79 Sqm 1,003.732 42,53,602.00
10.67.3 Size of Tile 800 x800 mm. 423.25 Sqm 1,181.439 5,00,043.00
Extra for grouting the joints of floor tiles having joints of 3 mm width, using
HSR-21 epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener
10.70 and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per
direction of Engineer-in-charge.
10.70.2 Size of Tile 600 x 600 mm. 5,015.30 Sqm 140.201 7,03,150.00
10.70.3 Size of Tile 800 x800 mm. 3,244.91 Sqm 112.518 3,65,111.00
HSR-21 Providing of stamping or making grooves for a depth of 2 mm on top of steps in stair
Providing and laying 60mm thick factory made cement concrete inter1ocking
paver block of M -30 grade made by block making machine with strong vibratory
46 compaction, of approved size, design & shape, laid in required colour and pattern over 185.00 Sqm 556.339 1,02,923.00
(BIS 15658:2006) and including 50mm thick compacted bed of coarse sand, filling the
joints with line sand etc. all complete as per the direction of Engineer-in-charge.
Providing and laying matt finished vitrified tile of size 300x300x9.8mm having
with water absorption less than 0.5% and conforming to IS: 15622 of approved make in
HSR-21 all colours and shades in for outdoor floors such as footpath, court yard, multi modals
10.106 location etc., laid on 20mm thick base of cement mortar 1 :4 (1 cement : 4 coarse sand)
in all shapes & patterns including grouting the joints with white cement mixed with
matching pigments etc. complete as per direction of Engineer-in-Charge.
Providing and laying tactile tile (for vision impaired persons as per standards) of
size 300x300x9.8mm having with water absorption less than 0.5% and conforming to
IS:15622 of approved make in all colours and shades in for outdoor floors such as
48 footpath, court yard, multi modals location etc., laid on 20mm thick base of cement 1,051.14 Sqm 1,604.721 16,86,782.00
mortar 1 :4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the
joints with white cement mixed with matching pigments etc. complete as per direction of
Engineer-in-Charge.
Providing and fixing 10x10x7.50 cm Granite stone block hand cut and chisel
HSR-21 dressed on top, for paving in floors, drains etc. laid over 20mm thick base mortar 1:4 (1
10.108 cement: 4 coarse sand) with joints 10mm wide filled with same mortar including ruled
pointing etc. complete as per direction of engineer-in-charge.
Authorised Signatory Contractor BOQ Page No. 10 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Providing and laying gang saw cut 30 mm thick, mirror polished pre moulded
and pre polished machine cut granite stone of required size and shape of approved
shade, colour and texture in footpath, flooring in road side plazas and similar locations,
laid over 20mm thick base of cement mortar 1 :4 (1cement : 4 coarse sand) including
50 grouting the joints with white cement mixed with matching pigment, epoxy touch ups etc. 168.69 Sqm 3,676.481 6,20,186.00
complete as per direction of Engineer-in-Charge.
1. Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.)
2. Colour/Shade to be approved by the University
51 10 mm thick cement plaster
11.4.2 1 : 3 (1 cement: 3 fine sand) 7,845.91 Sqm 85.728 6,72,614.00
52 12 mm cement plaster of mix :
11.5.4 1 : 6 (1 cement: 6 fine sand) 27,090.17 Sqm 67.868 18,38,556.00
53 15 mm cement plaster on the rough side of single or half brick wall of mix :
11.6.2 1 : 6 (1 cement: 6 fine sand) 19,716.93 Sqm 85.728 16,90,293.00
Providing and applying two coats white cement based putty of approved brand and
HSR-21 manufacturer, over plastered surface and grinding the surface smooth with sand paper to
11.58 get en even and smooth finish including cost and carriage of all material , labour charges,
scaffolding, sundries etc. complete
HSR-21 Distempering with oil bound washable distemper of approved brand and
11.64 manufacture to give an even shade:
New work (two or more coats) over and including water thinnable priming coat with
cement primer
HSR-21 Applying one coat of water thinnable cement primer of approved brand and
11.67 manufacture on wall surface:
11.67.1 Water thinnable cement primer. 2,049.27 Sqm 22.325 45,750.00
57 Applying priming coat:
With ready mixed red oxide zinc chromate primer of approved brand and manufacture
on steel galvanised iron/ steel works
HSR-21 Painting two coats excluding priming coat with synthetic enamel paint in all shades
11.78 on new wood work or metallic or plastered or concrete surfaces to give an even shade.
59 Finishing walls with Acrylic Smooth exterior paint of required shade :
New work (Two or more coat applied @ 1.67 litre/10 sqm over and including priming
coat of exterior primer applied @ 2.20 kg/10 sqm).
Providing wood work in frames of doors, windows, clerestory windows and other
60 frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of
required dia & length (hold fast lugs or dash fastener shall be paid separately).
12.1.3 Kiln seasoned and chemically treated Hollock wood 1.65 Cum 53,304.063 88,032.00
HSR-21 Providing wood work in frames of false ceiling, partitions etc. sawn and fixed in
12.4 position with necessary stainless steel screws etc.
12.4.2 Kiln seasoned and chemically treated Hollock wood 8.00 Cum 48,004.108 3,84,270.00
Authorised Signatory Contractor BOQ Page No. 11 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Providing & Fixing decorative high pressure laminated sheet of plain/ wood grain
in gloss / matt/ suede finish with high density protective surface layer and reverse side of
62 adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of
approved quality.
(Note:- Colour/Shade and company to be approved by the University)
12.12.2 1.0 mm thick 1,832.64 Sqm 459.895 8,42,822.00
Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part
HSR-21 I) non-decorative type, core of block board construction with frame of 1st class hard
12.37 wood and well matched commercial 3 ply veneering with vertical grains or cross bands
and face veneers on both faces of shutters:
12.37.1 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 756.82 Sqm 1,400.224 10,59,711.00
12.37.2 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws 18.98 Sqm 1,342.179 25,468.00
25 mm thick (for cupboard) including ISI marked nickel plated bright finished M.S.
piano hinges with necessary screws
HSR-21 Extra for providing lipping with 2nd class teak wood battens 25 mm minimum
12.39 depth on all edges of flush door shutters (over all area of door shutter to be measured).
HSR-21 Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors
12.40 (cost of glass excluded) (overall area of door shutter to be measured):
12.40.1 Rectangular or square. 872.89 Sqm 150.917 1,31,733.00
HSR-21 Providing and fixing IS : 12817 marked stainless steel butt hinges (heavy weight)
12.74 with stainless steel screws etc. complete :
12.74.1 125 x 64 x 2.50 mm 432.00 Each 75.905 32,791.00
HSR-21 Providing and fixing magnetic catcher of approved quality in cupboard/ ward robe
12.87 shutters, including fixing with necessary screws etc. complete.
12.87.2 Double strip vertical type 528.00 Each 23.218 12,259.00
Providing and fixing aluminium die cast body tubular type universal hydraulic
HSR-21 door closer (having brand logo with ISi, IS : 356 4, embossed on the body, door
12.88 weight up to 35 kg and door width up to 7 00 mm), with necessary accessories and
screws etc. complete.
Providing and fixing aluminium extruded section body tubular type universal
HSR-21 hydraulic door closer (having brand logo with ISi, IS: 3564, embossed on the body,
12.89 door weight up to 36 kg to 80 kg and door width from 701 mm to 1000 mm), with
double speed adjustment with necessary accessories and screws etc. complete.
Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic
70 coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required
colour or shade, with nuts and screws etc. complete :
12.98.1 300 x 16 mm 196.00 Each 200.925 39,381.00
12.98.2 250 x 16 mm 217.00 Each 178.600 38,756.00
Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating
71 not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or
shade, with necessary screws etc. complete.
12.99.1 300 x 10 mm 1,747.00 Each 95.551 1,66,928.00
12.99.4 150 x 10 mm 1,383.00 Each 61.617 85,216.00
12.99.5 100 x 10 mm 432.00 Each 46.436 20,060.00
Authorised Signatory Contractor BOQ Page No. 12 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
HSR-21 Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not
72 less than grade AC 1 O as per IS : 1868) transparent or dyed to required colour or shade,
with necessary screws etc. complete.
12.102.1 125 mm 1,060.00 Each 49.115 52,062.00
12.102.2 100 mm 1,814.00 Each 42.864 77,755.00
HSR-21 Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised
73 (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to
required colour and shade, with necessary screws etc. complete.
12.103.2 Twin rubber stopper -100mm 448.00 Each 51.794 23,204.00
HSR-21 Providing and fixing aluminium casement stays, ISI marked, anodised transparent
74 or dyed to required colour and shade or powder coated or polyester powder coated, with
necessary screws etc. complete.
12.104.4 Polyester powder coated minimum thickness 50 micron aluminium 1,166.00 Each 58.045 67,680.00
HSR-21 Providing Aluminium Jali of thickness 7mm thick with openings - 75mm x 75mm of
12.107 including anodizing and fixing in frame with cost of screws etc.
Providing and fixing factory made uPVC door frame made of uPVC extruded
sections having an overall dimension as below (tolerance ±1 mm), with wall thickness
2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets
76 and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the
frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1 mm (± 0.1 mm)
wall thickness and 3 Nos. stainless steel hinges fixed to the frame complete as per
manufacturer's specification and direction of Engineer- in-charge
12.117.2 Extruded section profile size 42x50 mm 367.50 Rmt 205.390 75,481.00
76 Providing and fixing to existing door frames.
25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded
PVC section of the size of 762 mm X 25 mm or less as per requirement with an average
wall thickness of 1 mm (:t 0.3 mm). PVC foam end cap of size 23x1 O mm are provided
on both vertical edges to ensure the overall thickness of 25 mm. M.S. tube having
dimensions 19 mm x 19 mm and 1.0 mm (± 0.1 mm) is inserted along the hinge side of
12.118.3 the door. Core of the door shutter should be filled with High Density Polyurethane foam. 130.90 Sqm 2,083.369 2,72,713.00
The Top & Bottom edges of the shutter are covered with an end-cap of the size 25 mm X
11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per
manufacturer's specification and direction of Engineer-incharge to take up necessary
hardware and fixtures. Stickers indicating the locations of hardware will be pasted at
appropriate places
Providing and fixing non load bearing fixed frame for fire resistant glazed
Partition for 120 minutes Fire Rating, made out to a profile of dimension 60mm x 70 mm
of 1.6 mm thick galvanised steel sheet as per test evidence suitable for fixing fire rated
glass for 120 minutes of both integrity & radiation control (EW120) & minimum 20
minutes of insulation (El20).The profile has to be fixed to the supporting construction by
76 means of anchor fasteners of size M10 x BO, every 150 mm from the edges and every 158.40 Rmt 1,213.587 1,92,232.00
500 mm (approx) c/c. Linear measurement of frame shall be measured for payment. The
frame shall be filled with mineral wool insulation of density min 96kg/ m3 • and finished
with a approved fire resistant primer or Powder coating of not less than 30 micron in
desired shade as per NBC 2016, IS 16231 (Part 3):2016 and directions of Engineer- in-
charge.
Authorised Signatory Contractor BOQ Page No. 13 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions
etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than
120 grn/m2) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm
from the edges and 150 mm c/c , including applying a coat of approved fire resistant
primer/powder coating of not less than 30 micron on G.I. beading, & special ceramic tape
of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016
HSR-21 and as per direction of Engineer-in-charge with glass of required thickness having 120
12.154 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20
minutes of insulation (El20). The manufacturer have to give test report/certification of fire
glass and the glass should have the stamp showing the value of E, EW & El. The glass
shall be tested in approved NABL accredited lab or by any other accreditation body which
operates in accordance with 1$0/IEC 17011 and accredits labs as per ISOnEC 17025 for
testing and calibration scopes shall be eligible. The maximum glazing size shall not be
more than 1100x2200 mm (w x h) or 2.42 sqm
Providing and fixing aluminium work for doors, windows, ventilators and
partitions with extruded built up standard tubular sections/ appropriate Z sections and
other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash
fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e.
78 at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium
sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever
required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass
/ stainless steel screws, all complete as per architectural drawings and the directions of
Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) :
Authorised Signatory Contractor BOQ Page No. 14 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
12.157.1 For fixed portion
Polyester powder coated aluminium (minimum thickness of polyester powder coating
50 micron)
For shutters of doors, windows & ventilators including providing and fixing hinges/
12.157.2 pivots and making provision for fixing of fittings wherever required including the cost of
EPDM rubber / neoprene gasket required (Fittings shall be paid for separately).
Polyester powder coated aluminium (minimum thickness of polyester powder coating
50 micron)
Providing and fixing 12 mm thick prelaminated particle board flat pressed three
HSR-21 layer or graded wood particle board conforming to IS: 12823 Grade I Type II, in panelling
79 fixed in aluminium doors, windows shutters and partition frames with C.P. brass /
stainless steel screws etc. complete as per architectural drawings and directions of
engineer-in-charge.
12.158.2 Pre-laminated particle board with decorative lamination on both sides. 248.35 Sqm 788.519 1,95,826.00
Providing and fixing double action hydraulic floor spring of approved brand and
manufacture conforming to IS : 6315, having brand logo embossed on the body / plate
HSR-21 with double spring mechanism and door weight up to 125 kg, for doors, including cost of
12.160 cutting floors, embedding in floors as required and making good the same matching to
the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet
outer box with slide plate etc. complete as per the direction of Engineer-in-charge.
12.160.1 With stainless steel cover plate minimum 1.25 mm thickness. 32.00 Each 1,898.518 60,753.00
Providing and fixing stainless steel (SS 304 grade) adjustable friction windows
81 stays of approved quality with necessary stainless steel screws etc. to the side hung
windows as per direction of Engineer-in-charge complete.
12.162.3 355 X 19 mm 432.00 Each 236.645 1,02,231.00
Providing and fixing 12 mm thick frameless toughened glass door shutter of
approved brand and manufacture, including providing and fixing top & bottom pivot &
82 double acting hydraulic floor spring type fixing arrangement and making necessary holes 8.64 Sqm 3,414.832 29,504.00
etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge
(Door handle, lock and stopper etc.to be paid separately).
Filling the gap in between aluminium/ stone/ wood frame and adjacent RCC/Brick/
Stone/ wood/ Ceramic/ Gypsum work by providing weather/structural non sag
83 elastomeric PU sealant over backer rod of approved quality as per architectural drawings
and direction of Engineer-in-charge complete, complying to ASTM C920, DIN 18540-F &
12.172.1 Up to 5 mm depth and 5 mm width. 18,389.60 Rmt 90.193 16,58,613.00
Providing and fixing glazing in aluminium door, window, ventilator shutters and
HSR-21 partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the
12.177 architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap
beading shall be paid in basic item):
12.177.1 With toughened glass panes of 6 mm thickness (weight not less than 15 kg/sqm) 3,060.96 Sqm 1,051.061 32,17,259.00
Providing and fixing carbon steel galvanised ( minimum coating 5 micron) dash
HSR-21 fastener of 10 mm dia double threaded 6.8 grade (yield strength 480 N/mm2), counter
13.5 sunk head, comprising of 10 mm dia polyamide PA 6 grade sleeve, including drilling of
hole in frame , concrete/ masonry, etc. as per direction of Engineer-in-charge.
Authorised Signatory Contractor BOQ Page No. 15 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
13.5.3 10 x 120mm 22,138.00 each 77.691 17,19,923.00
Authorised Signatory Contractor BOQ Page No. 16 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
13.5.4 10 x 140mm 6,328.00 each 87.514 5,53,789.00
13.5.5 10 x 160mm 2,099.00 each 108.946 2,28,678.00
HSR-21 Steel work welded in built up sections/ framed work, including cutting, hoisting,
86 fixing in position and applying a priming coat of approved steel primer using structural
steel etc. as required.
13.29.2 In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works 3,866.40 kg 83.049 3,21,101.00
Steel work in built up tubular (round, square or rectangular hollow tubes etc.)
HSR-21 trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of
13.30 approved steel primer, including welding and bolted with special shaped washers etc.
complete.
13.30.2 Hot finished welded type tubes. 25,107.68 kg 117.876 29,59,593.00
Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes,
channels, plates etc., including welding, grinding, buffing, polishing and making curvature
(wherever required) and fitting the same with necessary stainless steel nuts and bolts
HSR-21 complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners
13.41 , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab
with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose
only weight of stainless steel members shall be considered excluding fixing accessories
such as nuts, bolts, fasteners etc.).
Providing and laying water proofing treatment on roofs of slabs by applying cement
slurry mixed with water proofing cement compound consisting of applying:
(a) After surface preparation, first layer of slurry of cement @ 0.488 kg/sqm mixed with
water proofing cement compound @ 0.253 kg/sqm (b) Laying second layer of Fibre glass
cloth when the first layer is still green. Overlaps of joints of fibre cloth should not be less
than 10 cm.
HSR-21 (c) Third layer of 1.5 mm thickness consisting of sluny of cement @ 1.289 kg/sqm mixed
28.16 with water proofing cement compound @ 0.670 kg/sqm and coarse sand @ 1.289 kg/sqm
This will be allowed to air cure for 4 hours followed by water curing for 48 hours. The
entire treatment will be taken up to 30 cm on parapet wall and tucked into groove in
parapet all around.
(d) Fourth and final layer of brick tiling with cement mortar (which will be paid for
separately).
For the purpose of measurement the entire treated surface will be measured.
Providing and laying integral cement based water proofing treatment including
preparation of surface as required for treatment of roofs, balconies, terraces etc
consisting of following operations:
90 (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with
water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge
over the RCC slab including adjoining walls up to 300 mm height including cleaning the
surface before treatment.
Authorised Signatory Contractor BOQ Page No. 17 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
(b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115
mm size with 50% of cement mortar 1 :5 (1 cement : 5 coarse sand) admixed with water
proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20
mm thick layer of cement mortar of mix 1 :5 (1 cement :5 coarse sand ) admixed with
water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to
required slope and treating similarly the adjoining walls up to 300 mm height including
rounding of junctions of walls and slabs.
(c) After two days of proper curing applying a second coat of cement slurry using
2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS: 2645
and approved by Engineer-in-charge.
(d) Finishing the surface with 20 mm thick joint less cement mortar of mix 1:4 (1
cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645
and approved by Engineer-in-charge including laying glass fibre cloth of approved quality
in top layer of plaster and finally finishing the surface with trowel with neat cement slurry
and making pattern of 300x300 mm square 3 mm deep.
(e) The whole terrace so finished shall be flooded with water for a minimum
period of two weeks for curing and for final test. "All above operations to be done in
order and as directed and specified by the Engineer-in-Charge:
28.17.1 With average thickness of 120 mm and minimum thickness at khurra as 65 mm. 3,289.68 Sqm 664.392 21,85,637.00
91 Supplying and filling cinder on roof (up to three storeys) including light ramming. 609.55 Cum 1,236.805 7,53,894.00
Design supply & installation of suspended Spider Glazing system designed to
withstand the wind pressure as per IS 875 (Part-Ill). The Suspended System held with
Spider Fittings of SS-316 Grade Steel of approved manufacturer with glass panel having
12 mm thick clear toughened glass held together with SS- 316 Grade Stainless steel
Spider & bolt assembly with laminated glass fins 21.52 mm thick. The Glass fins and glass
panel assembly shall be connected to Slab/beams by means of SS- 316 Grade stainless
steel brackets & Anchor bolts and at the bottom using SS channel of 50x25x2mm using
92 fastener & anchor bolts, non staining weather sealants of approved make, Teflon/ nylon 54.00 Sqm 6,444.781 3,48,018.00
bushes and separators to prevent bi-metallic contacts, all complete to perform as per
specification and approved drawings. The complete system to be designed to
accommodate thermal expansion & seismic movements etc. The joints between glass
panels (6 to 8 mm) and gaps at the perimeter & in U channel of the assembly to be filled
with non staining weather sealant, so as to make the entire system fully water proof &
dust proof.
The rate shall include all design, Engineering and shop drawing including approval from
structural designer, labour, T&P, scaffolding, other incidental charges including wastage,
enabling temporary services all fitting fixers nut bolts, washer, Buffer plates, fastener,
anchors, SS channel laminated glass etc. all complete. For the purpose of payment,
actual elevation area of Glazing including thickness of joints and the portion of Glass
panel inside the SS channel shall be measured.
Authorised Signatory Contractor BOQ Page No. 18 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Providing and fixing mineral fibre false ceiling tiles at all heights of size
595X595mm of approved texture, design and pattern. The tiles should have Humidity
Resistance (RH) of 99%, Light Reflectance i!: 85%, Thermal Conductivity k = 0.052 -
0.057 w/m K, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level
suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33
mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length
3000 mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross
T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm
HSR-21 suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long
32.47 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to
1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm
centre to centre along main 'T'. The system should rest on periphery walls /partitions with
the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet,
to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm
long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false
ceiling support system shall be pre-painted with polyester baked paint, for all heights. The
work shall be carried out as per specifications, drawings and as per directions of the
engineer-in-charge.
With 16 mm thick bevelled tegular mineral fibre false ceiling tile (NRC 0.55 to
Providing 1.20 metre high fencing with angle iron posts 50 mm x 50 mm x 6 mm at 3
metre centre to centre with 0.40 metre embedded in M15 grade cement concrete, corner,
94 end and every 10th post to be strutted, provided with welded steel wire fabric of 75mm x 30.00 Rmt 661.713 19,851.00
25 mm mesh and fixed to iron posts by flat iron 50 x 5 mm and bolts etc. complete in all
respects.
TOTAL (i) 3074,48,125.00
NON-SCHEDULE ITEMS ( CIVIL WORK )
Disposal of surplus earth excavated from basement & foundation from the building by
95 Mechanical Transport including loading, unloading and stacking upto any lead within the 3,624.31 Cum 52.000 1,88,464.00
(Derived)
campus of University Complete in all respects.
Excavating, supplying and filling of Tibba Sand having CBR 8% (including royalty) by
96 mechanical transport upto any lead and Lift also including ramming and watering of the 1,575.00 Cum 152.000 2,39,400.00
(Derived)
earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.
NS-3 Extra rate for Using 20mm stone aggregate instead of 40mm Stone aggregate in
(Derived) cement concrete of grade ( 1:4:8, 1:5:10 ) complete in all respects.
Extra rate for using Machine moulded common burnt clay bricks of class
NS-4 designation 12.5 instead of common burnt clay bricks of class designation 10.5 for Honey-
98 comb brick work 10/11.4 cm thick in super structure above plinth level including making 81.77 Sqm 21.000 1,717.00
(Derived)
horizontal and vertical grooves 10mm wide 12mm deep with cement mortar 1 :4 (1
cement : 4 coarse sand).
Providing and fixing of Stainless Steel (SS-304) Glass Door Handle H-Type
99 32mmdia, 450 mm long with screws etc. complete in all respects to the entire satisfaction 4.00 Pair 1,685.000 6,740.00
and as per sample approved by Engineer-in-charge.
Providing and fixing Stainless Steel Corner Patch lock with euro profile cylinder and
N.S SS Strike plate having Dead bolt projection of 15mm (single throw) base material made
100 of Aluminium alloy casting covered with SS 316 covers and necessary screws etc. 4.00 Each 2,053.000 8,212.00
complete in all respects to the entire satisfaction and as per sample approved by Engineer-
in-charge.
Authorised Signatory Contractor BOQ Page No. 19 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
N.S Providing & fixing Stainless Steel ball bearing butt hinges of size 100 x 75 x 3mm
101 to Aluminium window/ Doors etc. (Grade 304) with nuts & screws etc complete. (as per 2,332.00 Each 265.000 6,17,980.00
sample approved by Engineer-in-charge).
ACOUSTICAL WALL PANELLING ABOVE 2.30m
Providing and fixing in position wall panelling at all heights with Fully Perforated
Gypsum Plaster Board of size 1200 x 2400 x 12.5 mm having approx. having 8 x 8mm
square perforations @ 20mm pitch - 25% open area, square edge, volume density of
base board 650 Kgs/m3, weight 8Kgs/m2, with all 4 side tapered and backed by
102 acoustical tissue with NRC value not less than 0.60, comprising of a frame made from 858.44 Sqm 1,878.000 16,12,150.00
especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section
(galvanizing @120 grams per sqm including both sides) i.e. vertical studs of size 48 x 34
x 36 mm are placed at 600mm centre to centre in a floor and ceiling channel section of
size 50 x 32m fixed to the floor and soffit at 600mm centres using 12mm dia,50mm long
wedge type expanded zinc alloy dash fastener with 10mm bolt.
This same channel is then to be fixed in horizontal direction at 600mm centre to centre so
as to form a grid of 600mm x 600mm. Synthetic polyester-fibre infill - 50mm thick of
density 1500 g/sqm having NRC 0.70 is then to be inserted in the slots held in position by
criss crossing GI chicken mesh 12.5mm x 24 SWG. and finally Fully Perforated Gypsum
Plaster Board panels/tiles are to be screw fixed with dry wall screws of size 3.5 x 25 mm
at 230 mm c/c on to this grid leaving an even groove of 4 mm between the panels. The
joints between the panels are to be duly jointed and finished to a flush finish of tapered
and square edges of the board with recommended jointing compound , jointing tapes ,
finishing with jointing compound in 3 layers covering up to 150 mm on both sides of joint
and two coats of primer suitable for board/panelling as per manufacturer's specification as
per direction of Engineer-in-Charge all complete.
ACOUSTICAL WOODEN WALL PANELLING UPTO 2.30 m
Providing and Fixing of Acoustical wooden grooved slats having system NRC not
less than 0.75 with lineal perforation made of pinewood EI grade HDF panels shall be
melamine/ veneer laminated finish of size 2440mm x128mm x 16mm with 2mm groove
at 16mm pitch with 27% open area, Tongue and Groove edges for seamless mounting
having density of base board 700-800kg/m3 (base panel confirming to IS 12406 and
laminated panel confirming to IS 14587). The back of the panels are perforated with
10mm dia holes and lined with a nonwoven fabric acoustical fleece covering of 0.27mm
103 for providing Sound absorption via the acoustic impedance method, Humidity Resistance 715.76 Sqm 6,027.000 43,13,855.00
(RH) of 50%, NRC upto 0.85, Fire Resistance as per BS476 (Part 6 & 7). Wooden grooved
slats is installed by using GI/Aluminium Strut Framework. The strut Frame work shall
include GI 'W profile (0.55 mm thick), having length 3600mm, knurled web of 40mm and
two flanges of 15mm each with lips of 10mm is fastened to wall vertically and horizontally
at every 600mm c/c in perimeter channel having one flange of 20 mm and another flange
of 30 mm with thickness of 0.55 mm and web of length 27 mm. Perimeter channel is
fixed on the floor and the ceiling with the nylon sleeves @ 610 mm CIC with fully
threaded self-tapping dry wall screws.
Authorised Signatory Contractor BOQ Page No. 20 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Then Aluminium core cross channel of thickness 0.5mm, length 2400mm, web 15mm &
27mm, depth 18mm and flanges of 7mm with suitable edge & center brackets is then
fixed perpendicular to the GI 'W profile strut with the help of fasteners at every 400mm
centers. Wooden grooved slats of size 128x 2440x16mm in then fixed perpendicular to
Aluminum Strut with suitable edge & centre brackets. The system is backlined with
Synthetic polyester-fibre infill - 50mm thick of density 1500 g/sqm having NRC 0.70 is
then to be inserted in the slots held in position by criss crossing GI chicken mesh 12.5mm
x 24 SWG as per manufacturer's specification as per direction of Engineer-in-Charge all
complete.
ACOUSTICAL SUSPENDED CEILING WITH WOODEN FINISH
Providing & Fixing of Acoustical Suspended Ceiling System – Tegular edge tile of
size 595 X 595 X 12 mm Lay in on 24 mm exposed GI Grid. Tiles made of pinewood EI
grade MDF panels shall be melamine/ veneer laminated finish with random perforation as
per manufacturer specifications .The back of the system are lined with a nonwoven fabric
acoustical fleece covering of 0.27mm for providing Sound absorption via the acoustic
impedance method. The tiles should have 1-test FR grade, size 595x595x12mm, Square
edge, volume density of base board 700Kg/m3, weight 8.4Kgs/m2, Humidity Resistance
(RH) of 50%, NRC upto 0.85, Fire Resistance as per BS476 (Part 6 & 7). The Grid should
be 24 mm wide T sections i.e. the Main Runner 3000mm in web height of 32 mm, 1200
mm & 600 mm Cross Tees in web height of 26mm to comprise main runner spaced at
104 1200mm centers securely fixed to the structural soffit using suspension system at 1,060.09 Sqm 5,253.000 55,68,666.00
1200mm maximum centre. The First/Last suspension system at the end of each main
runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm
long cross tees to be interlocked between main runners at 600mm centre to form 1200 x
600 mm module. Cut cross tees longer than 600mm require independent support. 600 x
600mm module to be formed by fitting 600mm long flush fitting cross tees centrally
between the 1200 mm cross tees. Perimeter trim to be wall angles of size
3000x19x19mm, secured to walls at 450 mm maximum centers and as per the drawing.
The system is backlined with Synthetic polyester-fibre infill - 50mm thick of density 1500
g/sqm having NRC 0.70 is then to be inserted in the slots held in position by criss crossing
GI chicken mesh 12.5mm x 24 SWG as per manufacturer's specification as per direction
of Engineer-in-Charge all complete.
N.S Providing Leather finishing to the Kota/Granite stone including all tools and material
C-7 required complete in all respects to the entire satisfaction of the Engineer-In-Charge.
Providing & fixing Fresh Color Restroom Cubicles Systems (MODEL TYPE - ZMS SS
SERIES) Thickness of Compact Laminate : 12 mm, Color of HPL Boards: Dual Colour,
Size of Cubicle : 1000mm (W) & 1550mm, (D) X 2003mm (H), Door Size : 1750mm (H) x
610mm (W), Overall Height Of Cubicle : 2003mm, (Including bottom Gap of
N.S 150mm),Accessories: Standard – Merino Make Aluminium, Stainless Steel - 304 Grade
C-8 accessories) a) Aluminium “U” Channel, b) Aluminium “F” channel, c) Aluminium Door
Stopper Channel, d) Aluminium Top Rail, e) SS Coat Hook, f) SS Privacy Thumb turn c/w
Occupancy Indicator, g) SS Door Knob, h) SS Hinges with Cover, i) SS Adjustable Foot
316 Grade j) Rubber Door Stopper Lining, k) S.S.Screws 304 G & P.V.C Wall Plugs
complete in all respects to the entire satisfaction of Engineer-in-Charge.
Authorised Signatory Contractor BOQ Page No. 21 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Providing and applying protective water repellent coating to rough Red sand stone /
dry clading with a spray of solvent based silicon coating of an approved make as per the
N.S manufacturer specification to the entire satisfaction of the engineer in charge. The whole
107 surface shall be cleaned and made free from all dirt, oil,grease, wax/dust or any other 2,976.39 Sqm 343.000 10,20,902.00
form of the foreign matter before the application of spray including cost of scaffolding
required for its application complete in all respects to the entire satisfaction of Engineer-in-
Charge.
Providing & Applying (Granite Atellio or equivalent) Texture Finished External
wall finishing system (Thickness 1.5 – 2.0) mm being a weather and Ultraviolet
Resistant, Water Repellent, Dust, Dirt and Stain Resistant, Fungus and Algae Resistant
natural Granite texture (100% Natural crushed Granite mixed with ceramic) of approved
make. 1 coat of Acrylic primer mixed with wall sealer diluted with water in the ratio 1:1:1
N.S (1 primer : 1 wall sealer : 1 water) after check of minor repair. 1st coat of Granite Chips
C-10 Texture to be applied with Trowel/Spray of approved shade (attainable thickness: 0.80 to
1.0mm). 2nd Coat of Granite chips Texture of same shade to be applied with spray over
the 1st coat of texture (attainable thickness: 0.70 to 1.0mm) Finally one coat of water
base acrylic protection coat applied with roller and brush to make surface streak
resistance. Permanent Finish. .The rate shall also cover the cost of scaffolding required for
its application.
Providing and fixing Fly proof wire mesh comprising combination of ( stainless steel
grade 304 wire gauge with wire of dia 0.5 mm and average width of aperture 1.4 mm in
both directions and Aluminium Mesh with opening 10mm x 10mm 1.6 mm thick ) in
109 aluminium/UPVC door, window, ventilator shutters and partitions etc. fixed on 3 mm thick 498.25 Sqm 1,508.000 7,51,355.00
MS flat iron cover moulding of 12.5 mm width, including EPDM rubber / neoprene gasket
etc. complete as per the architectural drawings and the directions of engineer-in-charge.
(Cost of aluminium/UPVC snap beading shall be paid in basic item):
Providing and fixing Internal Signage Plates made of SS-304 (20 guage) Rust
N.S free sheet with Raised Braile Language including all necessary accessories for fixing as Sq.
C-12 per design given by architect, complete in all respects to the entire satisfaction of inch
Engineer-In-Charge.
Providing and fixing Main Building Signage Board measuring 35'-0" X 6'-0" having
base panel comprising M.S pipes and with Aluminium channels skinned with 5.0mm thick
Acrylic sheet finished with 3M Vinyl in color/shade as per drawing/design to house AC-DC
N.S adapter and wiring, profile of letters shall be laser cut in Acrylic Sheet for mounting 2.5"
C-13 raised white acrylic letters with front eco-digital prints but small matter in 6.0 mm solid
on base board including LED Module complete in all respect as per approved Color
Scheme and Lettering style duly fixed at site including all taxes and freight complete in all
respects to the entire satisfaction of Engineer-In-Charge.
Providing and fixing Fire Shaft doors with Frame and Door made up of 2 mm thick MS
Sheet finished with Powder Coating In Regular RAL shades pure polyester/Epoxy
Polyester powder having coating thickness of 60-80 micron including 5mm thick clear
112 float glass of size 600 x 900mm and all accessories i.e SS Ball Bearing Hinges of size 100 22.68 Sqm 3,997.000 90,652.00
x 75 x 3mm complete with SS Screws, anchor fastners of M10X80mm length, Shaft lock
with allen key, SS Flush pull handle etc. complete in all respects to the entire satisfaction
of Engineer-In-Charge.
Authorised Signatory Contractor BOQ Page No. 22 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Providing and fixing 10mm thick multiwalled polycarbonate sheet at all levels as
per approved pattern for skylight/Dome over existing MS frame. Sheet should have
protective guard film of 25 microns minimum to avoid scratches during transportation or
as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping
screws with EPDM seal, and the joints shall be provided with 60mm wide aluminium
113 Channels, Aluminium strips 40mm wide at top and bottom and 10mm wide aluminium 338.00 Sqm 2,055.000 6,94,590.00
channel at ends including EPDM Rubber gaskets as a seal and Joints filled with all weather
sillicon sealent complete upto any pitch in horizontal/ vertical or curved surfaces as shown
in the drawing, (excluding the cost of MS purlins, rafters and trusses) and including
cutting of sheet to size and shape wherever required complete in all respects to the entire
satisfaction of Engineer-In-Charge.
Providing and fixing of 95 x 25 mm second class Teak wood klin seasoned planks
with tongue & groove joints. Teak wood planks to be of minimum length 750mm. The
Teak wood planks to be fixed over two staggerd layers of 12 mm thick MR grade ply of
approved make fixed to Sal wood frame work of 50 x50 mm and 50x50 mm at 600 mm
centre to centre (HxV). The Sal wood shall be kiln seasoned and chemically treated. The
114 framework to be jointed with mathani cut method. The framework to be supported on 70.81 Sqm 6,076.000 4,30,257.00
100 x 100 x 10mm PVC/Rubber Levelling sim pads. The framework to be filled with 50
mm thick Resin bonded rock wool conforming to IS: 8183, density 48 kg/m3, 50 mm
thick, wrapped in 200 G virgin Polythene bags. The stage floor to be Melamine polished
with use of orbital sanders to make floor even before polishing complete in all respects to
the entire satisfaction of Engineer-In-Charge.
Supplying and fixing of minimum 52mm thick Non-Metallic Fire Proof Doors of
120 minutes fire rating consisting of :
1. DOOR FRAME: Made of Red Merranti Frame of section 120mm x 70mm with heat
activated intumescent fire seal strip of size 10mm x 4mm (Marshall/Lorient /Astroflame)
and one coat of anti-termite fire retardent primer.
2. DOOR SHUTTER: Made of 52mm thick asbestos free composite fire /smoke check
wodden shutters of 120 minutes fire rating conforming to BS: 476 Part 22 & IS:3164 Part-
N.S 2 comprising of two 9 mm thick starpan calcium silicate boards, a 100% without
115 asbestos, brucit and meerschaum, having density not less than 1150 kg/Cum and thermal 50.40 Sqm 12,561.000 6,33,074.00
conductive 0.14 W/m*K ply on both side and heat activated intumescent fire seal strip of
size 10mm x 4mm mounted in the grooves of hardwood lipping on all sides expect
bottom. The manufacturer shall have already tested a proto type door duly attested from
CBRI Rookee with vision panel for both single and double leaf shutter prior to supply. The
item also includes 1 mm thick laminate of approved shade and colour on both sides, SS
Ball Bearing hinges of Size 100 x 75 x 3mm with ss screws and anchor fastner of Size
M10x120mm of approved make. Size of clear opening of wall to be measure for payment
purpose.
Supplying and fixing of 120 minutes fire rated CBRI tested as per IS:3614 Part-2
and BIS:7 Part-22 stainless steel 304 grade outside access device (Trim and Lock)
116 compatible with single and double leaf panic bars from IR Monarch Series/Dorma PHA 12.00 Each 3,466.000 41,592.00
Series/Marshall/BAKER FS/ASSA ABLOY MH-PB-SS series prior tested from CBRI Roorkee
along with fire door to be approved by the Engineer- in- charge, all complete.
Authorised Signatory Contractor BOQ Page No. 23 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Supplying and fixing of 120 minutes fire rated CBRI tested as per IS:3614 Part-2
and BIS:7 Part-22 stainless steel 304 grade push type panic bars on double leaf
117 door shutters from IR Monarch Series/Dorma PHA Series/Marshall/BAKER FS/ASSA 12.00 Each 9,658.000 1,15,896.00
ABLOY/BAKER FS MH-PB-SS series prior tested from CBRI Roorkee along with fire door to
be approved by the Engineer- in- charge, all complete.
Supplying and fixing of 120 minutes fire rated CBRI tested as per IS:3614 Part-2
and BIS:7 Part-22 Door closer having rack & pinion mechanism, with standarad arm,
118 dual speed control, CE certifier, IR LCN 1461 Series/Dorma TS-73 Series/Marshall/ASSA 24.00 Each 3,068.000 73,632.00
ABLOY MH DC-S-14003 series prior tested from CBRI Roorkee along with fire door to be
approved by the Engineer- in- charge, all complete.
Providing and laying Anti- Skid/ Matt Finished Glazed Vitrified floor tiles of size
600 x 600mm (thickness to be specified by the manufacturer) with water absorption less
N.S than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades,
C-21 laid on 20mm thick cement mortar 1 :4 (1 cement : 4 coarse sand), jointing with grey
cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and
matching pigments etc., complete.
TOTAL (ii) 304,80,556.00
TOTAL ( i + ii) (A) 3379,28,681.00
Authorised Signatory Contractor BOQ Page No. 24 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
( PUBLIC HEALTH WORK )
Sr. Basic
HSR No. Description of Item Qty. Unit Amount
No. Rate
(B) PUBLIC HEALTH WORK - AS PER HSR 2021
Excavating trenches of required width for pipes, cables, etc including excavation
for sockets, and dressing of sides, ramming of bottoms, depth up to 1.5 m, including
1 getting out the excavated soil, and then returning the soil as required, in layers not
exceeding 20 cm in depth, including consolidating each deposited layer by ramming,
watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m:
4.16.1 All kinds of soil
4.16.1.2 Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia. 870.00 Rmt 61.617 53,607.00
HSR-21 Providing and laying in position cement concrete of specified grade excluding the
6.1 cost of centering and shuttering - All work below plinth level and up to Floor IV level:
1:2:4 (1 cement : 2 coarse sand (zone-Ill) : 4 graded stone aggregate 20 mm
nominal size)
Extra for providing opening of required size & shape for wash basin/ kitchen
HSR-21 sink in kitchen platfonn, vanity counter and similar location in marble/ Granite/stone
8.28 work, including necessary holes for pillar taps etc. including moulding, rubbing and
polishing of cut edges etc. complete.
Providing and fixing stone slab with table rubbed, edges rounded and polished,
of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of
HSR-21 appropriate width with chase cutter and embedding the stone in the chase with epoxy
8.30 grout or with cement concrete 1 :2:4 (1 cement: 2 coarse sand : 4 graded stone
aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished
smooth.
Granite Stone of approved shade
1. Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.)
2. Colour/Shade to be approved by the University
Providing and fixing on wall face Unplasticised Rigid PVC rain water pipes
HSR-21 conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS :
9.57 5382, leaving 10 mm gap for thermal expansion.
(i) Single socketed pipes.
9.57.2 110 mm dia PVC pipe 24.00 Rmt 200.032 4,801.00
9.57.3 150 mm dia PVC pipe 1,080.00 Rmt 268.793 2,90,296.00
Providing and fixing on wall face Unplasticised - PVC moulded
HSR-21 fittings/accessories for Unplasticised Rigid PVC rain water pipes conforming to IS :
9.58 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm
gap for thermal expansion.
9.58.2 Single push fit Coupler
9.58.2.1 75 mm 312.00 Each 49.115 15,324.00
9.58.2.2 110 mm 162.00 Each 74.119 12,007.00
9.58.3 Single tee with door
9.58.3.1 75 x 75 x 75 mm 265.00 Each 104.481 27,687.00
9.58.3.2 110 x 110 x 110 mm 85.00 Each 155.382 13,207.00
Authorised Signatory Contractor BOQ Page No. 25 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
9.58.4 Single tee without door
9.58.4.1 75 x 75 x 75 mm 132.00 Each 89.300 11,788.00
9.58.4.2 110 x 110 x 110 mm 24.00 Each 142.880 3,429.00
9.58.5.1 75 mm bend 90.00 Each 58.938 5,304.00
9.58.5.2 110 mm bend 184.00 Each 92.872 17,088.00
9.58.5.3 150 mm bend 60.00 Each 129.485 7,769.00
9.58.6 Shoe (Plain)
9.58.6.1 75 mm Shoe 54.00 Each 50.008 2,700.00
9.58.6.2 110 mm Shoe 27.00 Each 78.584 2,122.00
HSR-21 Cement Concrete 1:8:16 with stone aggregate 40 mm size in cum foundation and
10.100.2 plinth.
Cutting holes up to 23 cm through stone masonry or brick work in cement walls
8 for pipes and making good including repointing, replastering and finishing according to
existing finish where required.
20.26.1 11.43 cm thickness of walls 75.00 Each 164.312 12,323.00
20.26.2 22.86 cm thickness of walls 75.00 Each 242.003 18,150.00
Making connection with the existing G.I. branch main up to 40 mm size including
9 cutting and threading pipe etc., complete excluding cost of tee and long screw, but 1.00 Each 322.373 322.00
including cartage of material to site.
Bailing out water from the trenches for making new connections in fully charged
10 pipe-lines including cleaning trimming and dressing the trenches to correct alignment and
grade as required by the Engineer-in-charge.
Size of the main with which connection is to be made.
20.49.1 Up to 200 mm internal diametre. 2.00 Each 949.259 1,899.00
20.49.3 Exceeding 300 mm internal diametre but not exceeding 450mm internal diametre. 1.00 Each 1,477.022 1,477.00
Providing, lowering, laying, cutting (cut surface to be uniformly finished), jointing
with rubber rings marked with IS : 5382 and testing of SPIGOT AND SOCKETTED RCC,
11 NP2 MARKED WITH IS : 458-1988 and specials into trenches for all depths including
carriage, loading, unloading, stacking, handling, re-handling etc. complete is all respects
to the satisfaction to the Engineer - in -charge.
20.62.3 300 mm internal dia 410.00 Rmt 383.990 1,57,436.00
Constructing brick masonry inspection Chamber sizes as given below up to 0.60
metre average depth in cement mortar 1 :5 lime concrete with 40 per cent lime mortar
2:3 in foundation cement concrete 1 :2:4 benching 12mm thick cement plaster 1 :2 with
12 a floating coat of 1 mm thick of neat cement R.C.C. 1 :2:4 slab 100 mm thick/cement
concrete topping, 50mm thick: with 455mmx455mm / 455mm x610mm inside light duty
C.I.inspection chamber cover and frame weight as per 1.5.1. specification painted with 3
coats of black bitumastic superior paint complete as per standard design.
Size 450 mm X450 mm inside (with 455 mm x 455 mm cover and frame light duty
single seal weighing 20 kg with C.C. topping
Size 450 mm X 600 mm inside (with 455 mm x 610 mm cover and frame single seal
pattern I weighing 38 kg with C.C. topping)
Size 600 mm X900 mm inside (with 455 mm x 455 mm cover and frame light duty
single seal weighing 20 kg with R.C.C. slab)
Authorised Signatory Contractor BOQ Page No. 26 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Lowering salt glazed stoneware pipes and specials into trenches for all depths and
laying out the same to correct alignment gradient, level etc in trenches including all
dressing and trimming of bed and sides of trenches, if required, trimming and cutting of
concrete beds and joint holes, supporting the pipes and specials, in correct position in a
suitable rigid manner while the same are being jointed and until the surrounding benching
13 hunching and envelopes are completed. The sewer shall rest on the bed at every point
throughout its length and to ensure this, it shall be grouted in without extra charge by
the contractor with lime surkhi mortar, in the case of lime concrete beds and 1 :3 cement
sand mortar in the case of cement concrete beds including cartage from Divisional Store
or nearest Railway station to site of work.
The internal diameter of sewer being :-
21.38.2 150 mm internal diameter of sewer 100.00 Rmt 37.953 3,795.00
21.38.4 200 mm internal diameter of sewer 360.00 Rmt 49.294 17,746.00
Jointing and fixing salt glazed stoneware pipes and special in trenches using
cement sand mortar 1 :1 and best white Italian tarred hemp/yam including finishing and
HSR-21 trowel ling of each joint at an angle of 45 degrees with the longitudinal axis of the pipes,
21.39 watering, keeping the joints covered and wetted till the same are cured, testing the
sewer lines for leakages and making all leakages and defect good, complete as laid down
in the contract specifications.
21.39.2 150 mm internal diameter of sewer 167.00 Joint 57.152 9,544.00
21.39.4 200 mm internal diameter of sewer 600.00 Joint 75.012 45,007.00
Cutting glazed stoneware pipes and specials chipping and finishing the cut surface to
15 a uniform finish and roughing the part of the pipes, if any entering the sockets of the
adjacent pipes complete, to the satisfaction of the engineer-in-charge of the works.
21.40.2 150 mm internal diameter of sewer 20.00 Cut 20.539 411.00
21.40.4 200 mm internal diameter of sewer 45.00 Cut 27.683 1,246.00
Providing salt glazed stone ware pipes grade 'A' in standard length of 600 mm each
pipe marked with IS: 651 and their lowering, cutting, jointing and testing as described in
16 item No. 21.38, 21.39, item 21.40 induding the cost of jointing materials as well as
carriage, loading, unloading, stacking, handling, re-handling etc. complete in all respects
to the satisfaction of Engineer-in-charge.
21.94.2 150mm internal diameter 100.00 Rmt 187.530 18,753.00
21.94.3 200mm internal diameter 360.00 Rmt 238.431 85,835.00
HSR-21 Making holes for HCL soil / Waste pipe by core cutting up to 200 mm thick slabs
21.100 and sealing with Drip seal sealant complete in all respect.
21.100.2 100mm dia pipe. 374.00 Each 637.602 2,38,463.00
HSR-21 Providing and fixing MS Angle 35 x 35 x 5 mm with 10 mm MS Threaded rods &
21.101 Fastener & Fixture to Support the Cl and PVC Pipe.
HSR-21 Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983
19 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and
brackets, cutting and making good the walls wherever required.
22.10.1 Kitchen sink with drain board
22.10.1.1 510x1040 mm bowl depth 250 mm 17.00 Each 3,719.345 63,229.00
22.10.2 Kitchen sink without drain board
22.10.2.2 610 x 460 mm bowl depth 200 mm 22.00 Each 1,924.415 42,337.00
HSR-21 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste
22.14 fittings complete.
22.14.2 Flexibe Pipe
Authorised Signatory Contractor BOQ Page No. 27 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
22.14.2.1 32mm dia 232.00 Each 57.152 13,259.00
HSR-21 Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make
22.15 and as per the direction of Engineer-in-charge.
Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100
mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including
22 flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with
all fittings and fixtures complete, including cutting and making good the walls and floors
wherever required:
White vitreous chinaware Orissa pattern W.C. pan of size 580x440 mm with integral
type foot rests
Providing and fixing white vitreous chinaware pedestal type water closet
(European type) with seat and lid, 10 litre low level white vitreous chinaware flushing
HSR-21 cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow
22.24 arrangement with specials of standard make and mosquito proof coupling of approved
municipal design complete, including painting of fittings and brackets, cutting and making
good the walls and floors wherever required :
22.24.1 W.C. pan with ISi marked white solid plastic seat and lid 48.00 Each 4,386.416 2,10,548.00
Providing and fixing white vitreous chinaware extended wall mounting water
closet of size 780x370x690 mm of approved shape including providing & fixing white
24 vitreous chinaware cistern / PVC cistern (with brass fitting) into the wall with dual flush 12.00 Each 10,808.872 1,29,706.00
fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including seat
cover, and cistern fittings, nuts, bolts and gasket etc complete.
Providing and fixing 8 mm dia C.P. I S.S. Jet with flexible tube up to 1 metre long
25 with S.S. triangular plate to European type W.C. of quality and make as approved by 60.00 Each 241.110 14,467.00
Engineer - in - charge.
Providing and fixing M.S. holder-bat clamps of approved design to Sand Cast
HSR-21 iron/cast iron (spun) pipe embedded in and including cement concrete blocks 10x10x10
22.53 cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal
size), including cost of cutting holes and making good the walls etc. :
22.53.1 For 100 mm dia pipe 300.00 Each 144.666 43,400.00
22.53.2 For 75 mm dia pipe 150.00 Each 141.094 21,164.00
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal
stability for hot & cold water supply, including all CPVC plain & brass threaded fittings,
27 including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes &
fittings with one step CPVC solvent cement and testing of joints complete as per direction
of Engineer in Charge.
Internal work - Exposed on wall
22.85.3 25 mm nominal outer dia Pipes 405.00 Rmt 233.073 94,395.00
22.85.4 32 mm nominal outer dia Pipes 877.50 Rmt 310.764 2,72,695.00
22.85.5 40 mm nominal outer dia Pipes 742.50 Rmt 429.533 3,18,928.00
22.85.6 50 mm nominal outer dia Pipes 200.00 Rmt 648.318 1,29,664.00
Authorised Signatory Contractor BOQ Page No. 28 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal
stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c
28 fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings
with one step CPVC solvent cement and the cost of cutting chases and making good the
same including testing of joints complete as per direction of Engineer in Charge.
Concealed work, including cutting chases and making good the walls etc.
22.86.2 20 mm nominal outer dia pipes. 807.20 Rmt 264.328 2,13,366.00
22.86.3 25 mm nominal outer dia pipes. 886.00 Rmt 333.089 2,95,117.00
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal
HSR-21 stability for hot & cold water supply including all CPVC plain & brass threaded fittings This
22.87 includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling
& testing of joints complete as per direction of Engineer in Charge.
22.87.6 50 mm nominal outer dia Pipes 150.00 Rmt 592.059 88,809.00
HSR-21 Providing and fixing gun metal gate valve with C.I. wheel of approved quality
22.98 (screwed end):
22.98.2 20 mm internal diameter 30.00 Each 383.990 11,520.00
22.98.1 25 mm internal diameter 40.00 Each 414.352 16,574.00
22.98.3 32 mm internal diameter 30.00 Each 484.899 14,547.00
22.98.4 40 mm internal diameter 30.00 Each 567.055 17,012.00
22.98.5 50 mm internal diameter 10.00 Each 730.474 7,305.00
31 Providing and fixing Unplasticised PVC connection pipe with brass unions:
22.101.2 45 cm length
22.101.2.1 15 mm nominal bore 376.00 Each 50.901 19,139.00
32 Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931
22.104.1 15 mm nominal bore 107.00 Each 345.591 36,978.00
HSR-21 Providing and fixing C.P. brass long body bib cock of approved quality conforming to
22.106 IS standards and weighing not less than 690 gms.
22.106.1 15 mm nominal bore 111.00 Each 457.216 50,751.00
HSR-21 Providing and fixing C.P. brass stop cock (concealed) of standard design and of
22.107 approved make conforming to IS:8931.
22.107.1 15 mm nominal bore 108.00 Each 508.117 54,877.00
HSR-21 Providing and fixing C.P. brass angle valve for basin mixer and geyser points of
22.108 approved quality conforming to IS:8931.
22.108.1 15 mm nominal bore 304.00 Each 443.821 1,34,922.00
HSR-21 Providing and fixing C.P. Brass extension nipple (size 15mmx50mm) of approved
22.109 make and quality as per direction of Engineer-in-charge.
HSR-21 Providing & fixing chrome plated brass battery based infrared sensor operated pillar
22.110 cock, having foam flow technology.
22.110.1 15 mm nominal bore. 11.00 Each 6,730.541 74,036.00
HSR-21 Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved
22.115 quality and colour.
Waste coupling 36 mm dia of 83 mm length and 77mm breadth, weighing not less
than 60 gms.
Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and
39 112 mm distance from wall of standard shape with bracket of the same materials with 143.00 Each 126.806 18,133.00
snap fittings of approved quality and colour, weighing not less than 105 gms.
Authorised Signatory Contractor BOQ Page No. 29 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
HSR-21 Providing and fixing PTMT towel ring trapezoidal shape 215 mm long, 200 mm
40 wide with minimum distances of 37 mm from wall face with concealed fittings 143.00 Each 166.991 23,880.00
arrangement of approved quality and colour, weighing not less than 88 gms.
Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I.
HSR-21 grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm
22.166 size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than
2.70 kg as per standard design:
22.166.2 150 x 100 mm size P type
22.166.2.1 With common burnt clay non-modular bricks of class designation 10.5 44.00 Each 1,488.631 65,500.00
Providing and placing on terrace (at all floor levels) polyethylene water storage
HSR-21 tank, IS: 12701 marked, with cover and suitable locking arrangement and making
42 45,000.00 Litre 7.144 3,21,480.00
22.181 necessary holes for inlet, outlet and overflow pipes but without fittings and the base
support for tank.
Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in
43 cement mortar 1 :4 (1 cement : 4 coarse sand) including 500x450 mm precast R.C.C.
horizontal grating with frame and vertical grating complete as per standard design
22.207.1 With common burnt clay non-modular bricks of class designation 10.5. 25.00 Each 5,459.802 1,36,495.00
Providing and fixing 600x450 mm bevelled edge mirror of superior glass (of
44 approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats 143.00 Each 812.630 1,16,206.00
with C.P. brass screws and washers complete.
Providing and fixing in position vitreous chinaware white lavatory suites of
HSR-21 approved make (to the approval of Engineer-in-charge) including Rack Bolt Screw Pair
22.221 115mm long without CP fittings complete in all respect.
22.221.6: Size 560mm x 410mm (above counter oval)
22.221.8 Size 630mm x 500mm (above counter oval) 131.00 Each 3,985.459 5,22,095.00
Providing and fixing in position singel socket SWR UPVC soil waste or
46 antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed
firm including cutting, jointing, wastage, but excluding cost of jointing.
22.222.2 Single Socket Type-B
22.222.2.2 110mm O/d SWR UPVC pipe lines laid complete. 1,175.50 Rmt 322.373 3,78,949.00
22.222.2.3 90mm O/d SWR UPVC pipe lines laid complete. 3,305.50 Rmt 273.258 9,03,254.00
Making connection of drain or sewer line with existing manhole including breaking
into and making good the walls, floors with cement concrete 1 :2:4 mix (1 cement : 2
47 coarse sand : 4 graded stone aggregate 20 mm nominal size) cement plastered on both
sides with cement mortar 1 :3 (1 cement : 3 coarse sand), finished with a floating coat of
neat cement and making necessary channels for the drain etc. complete :
30.88.1 For pipes 100 to 250 mm diameter 1.00 Each 239.324 239.00
30.88.2 For pipes 250 to 300 mm diameter 1.00 Each 283.081 283.00
30.88.3 For pipes 350 to 450 mm diameter 1.00 Each 409.887 410.00
TOTAL (i) 68,63,721.00
NON-SCHEDULE ITEMS ( PUBLIC HEALTH WORK )
Providing and fixing in position set of EWC of size ( 66 x 35 x 88cm) and WHB of size
(46 x 36 x 18cm) for Differently abled person consisting of matching cistern, one pair
mounting brackets, seat cover, one(1) no. Foldable U Type (SS Grade_304) hinged rail
48 76cm and four(4) no. grab rails 60cm complete in all respect and to the entire 12.00 Each 44,791.000 5,37,492.00
satisfaction of Engineer-in-charge.
(Make:- Hindware (Catalogue No. 70002 - MATRIX SET) or similar model of Equivalent
make such as Jaquar/Parryware etc.)
Authorised Signatory Contractor BOQ Page No. 30 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Providing & fixing Urinal with spreader hole (URS-WHT-13261H)
NS Size:355x340x535mm including all fixing accessories with waste coupling (ALD-705L130)
PH-2 complete in all respects of (JAQUAR or similar model of Equivalent make such as
Hindware/Parryware etc.)
Providing & fixing Urinal Valve Auto Closing System (PRS-077) with Built-in
NS Control Cock and Flange including all fixing accessories and Urinal Spreader bowl Top
PH-3 Inlet 15mm with Fixing Stud (ALD 1043) complete in all respects of (JAQUAR or similar
model of Equivalent make such as Hindware/Parryware etc.)
Providing & fixing Pressmatic Type Pillar Cock Auto Closing System with 65 mm
51 extension body (PRS-031L65) including all fixing accessories complete in all respects of 132.00 Each 2,526.000 3,33,432.00
(JAQUAR or similar model of Equivalent make such as Hindware/Parryware etc.)
Supply, Installation, Testing and Commissioning of S.S DRAIN TROUGH WITH
GRATING of size 350mm(b) x 75mm(h) in SS Construction of AISI 304 Grade with
Stainlesss Steel Fully Trough made of 1.6mm thick Stainless Steel (SS 304) sheet made
to shape as per drawing with SS Grating ( Outer frame made of SS 304G Flat 25x4mm
NS and Inner frame made of SS 304G Flat fixed at 25mm c/c laterally and at 75mm c/c
PH-5 longitudinally fixed as per drawing. Channel Box is designed to be used in commercial
applications with concrete,resin or Tiles Floor with SS Perforated Grating made as per
manufacturer specifications or as per approval of Engineer-in Charge.Cost of required
frame work as per manufacturer specification is included in the Price. Nothing shall be
paid extra for any petty item required to make the Drain operational.
NS Providing and fixing in position 90mm o/d UPVC plain Nahani Trap conforming to
53 I.S.I. specifications and of self cleaning design with C.P. brass hinged grating with frame 376.00 Each 736.000 2,76,736.00
complete.
NS Providing and laying in position 63mm o/d UPVC Drain pipe conforming to IS :
PH-7 13592 Type A, including jointing with adhesive complete in all respects.
TOTAL (ii) 23,72,362.00
TOTAL ( i + ii) (B) 92,36,083.00
Authorised Signatory Contractor BOQ Page No. 31 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
( ROAD WORK )
Sr. Basic
HSR No. Description of Item Qty. Unit Amount
No. Rate
C ROAD WORKS - AS PER HSR 2021
Earth work in excavation by mechanical means (Hydraulic excavator) / manual
HSR-21 means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on
1 plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including
getting out the excavated soil and disposal of surplus excavated soil as directed, within a
lead of 50 m.
4.14.1 All kinds of Soil 124.65 Cum 83.049 10,352.00
HSR-21 Filling available excavated earth (excluding rock) in trenches, plinth, sides of
2 foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited 83.10 Cum 46.436 3,859.00
layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
HSR-21 Providing and laying in position cement concrete of specified grade excluding the
6.1 cost of centering and shuttering - All work below plinth level and up to Floor IV level:
6.1.7 1:5:10 (1 cement : 5 coarse sand (zone-Ill): 10 graded stone aggregate 20 mm
(Derived) nominal size).
Steel reinforcement for R.C.C. work, where not included in the complete rate of
RCC, including straightening, cutting, bending, placing in position, binding, wastage,
overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc.
complete in all respect below plinth level.
4 Note:- Reinforcement shall be measured in length including hooks, if any, separately for
different diameters as actually used in work , excluding overlaps. Wastage, overlaps,
couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or
other methods of binding & placing shall not be measured and cost of these items shall be
deemed to be included in the rates for reinforcement.
Thermo-Mechanically Treated bars of grade Fe-500D or more.
(Note: - TMT FE-550D bars to be used.)
Providing and fixing at or near ground level precast cement concrete in kerbs,
5 edgings etc. as per approved pattern and setting in position with cement mortar 1 :3 (1
Cement : 3 coarse sand), including the cost of required centering, shuttering complete.
1:1½:3 (1 Cement: 1½ coarse sand(zone-111) : 3 graded stone aggregate 20 mm
nominal size)
HSR-21 Brick work with common burnt clay non-modular bricks of class designation 10.5 in
7.21 foundation and plinth in:
7.21.2 Cement mortar 1:6 (1 cement: 6 coarse sand). 116.16 Cum 3,531.815 4,10,261.00
HSR-21 Providing and laying polythene sheet ( 125 micron ) under CC M-25/M-30 in road
10.17 and parking complete in all respect.
Providing and laying 500x 500x 40 mm thick Turf paver (Turf pave XD) on 150
HSR-21 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and
8 base course and filling with 150 mm thick jamuna sand, including spreading, well 612.00 Sqm 909.074 5,56,353.00
ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-
in-charge.
Authorised Signatory Contractor BOQ Page No. 32 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Providing and laying matt finished vitrified tile of size 300x300x9.8mm having
with water absorption less than 0.5% and conforming to IS: 15622 of approved make in
HSR-21 all colours and shades in for outdoor floors such as footpath, court yard, multi modals
10.106 location etc., laid on 20mm thick base of cement mortar 1 :4 (1 cement : 4 coarse sand)
in all shapes & patterns including grouting the joints with white cement mixed with
matching pigments etc. complete as per direction of Engineer-in-Charge.
10 Finishing walls with Acrylic Smooth exterior paint of required shade :
New work (Two or more coat applied @ 1.67 litre/10 sqm over and including priming
coat of exterior primer applied @ 2.20 kg/10 sqm).
Construction of Embankment CBR 8% (for new road/ raising/berms/etc.) with
HSR-21 Tibba Sand obtained from borrow pits, including compensation of earth with all lead and
17.6 lift transporting to site, spreading, grading to required slope and compacting to meet
requirement of table 300-2, as per technical clause 305 of MORT&H specifications.
Granular Sub-Base with Coarse Graded
Material - Grading-I or II or III (Table:- 400-2)
Construction of granular sub-base by providing coarse graded material, spreading in
12 uniform layers with motor grader on prepared surface, mixing by mix in place method 204.00 Cum 1,043.917 2,12,959.00
with Rotavator at OMC, and compacting with vibratory roller to achieve the desired
density, complete as per clause 401.of MORT&H specifications.
Grading III material.
Construction of unreinforced plain cement concrete pavement in M-30 mix design
over a prepared sub base with OPC 43 grade conforming to IS:383 mixed with concrete
HSR-21 mixer using batch type concrete mixer as per IS:1791, laid in position, compacted with
17.72 needle vibrator, screed vibrator and plate vibrator, dewatering of free water with vaccum
pump, finishing the surface with power floater, finishing to required lines and grades as
per drawings and technical clause 1501 of MORTH specifications.
TOTAL (i) 43,14,872.00
NON-SCHEDULE ITEMS ( ROAD WORK )
Providing and Filling Construction & Longitudinal joints (6 mm wide x 65 mm
NS deep) in VDC/PQC M-30 by groove cutting machine, providing and filling joints with
14 Polysulphide Pour Grade sealent of approved make in the VDC M-30 complete as per 906.67 Rmt 395.000 3,58,133.00
specifications and directions of Engineer-incharge. (Item of dowel bars / tie bars to be
paid separately).
TOTAL (ii) 3,58,133.00
TOTAL ( i + ii) (C) 46,73,005.00
Authorised Signatory Contractor BOQ Page No. 33 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
( RWH WORK )
Sr. Basic
HSR No. Description of Item Qty. Unit Amount
No. Rate
(A) CIVIL WORK - AS PER HSR 2021
Earth work in excavation by mechanical means (Hydraulic excavator) / manual
HSR-21 means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on
1 plan), including dressing of sides and ramming of bottoms, lift up to 1.5 m, including
getting out the excavated soil and disposal of surplus excavated soil as directed, within a
lead of 50 m.
4.14.1 All kinds of soil 49.76 Cum 83.049 4,133.00
HSR-21 Filling available excavated earth (excluding rock) in trenches, plinth, sides of
2 foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited 93.27 Cum 46.436 4,331.00
layer by ramming and watering, lead up to 50 m and lift up to 1.5 m.
HSR-21 Providing and laying in position cement concrete of specified grade excluding the
6.1 cost of centering and shuttering - All work below plinth level and up to Floor IV level:
1 :4: 8 ( 1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm
nominal size).
Reinforced cement concrete work in beams, suspended floors, cum roofs having
slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills,
4 staircases and spiral stair cases above plinth level up to floor four level, excluding the cost 7.48 Cum 6,112.585 45,706.00
of centering, shuttering, finishing and reinforcement with 1: 1.5:3 (1 cement : 1.5 coarse
sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).
HSR-21 Centering and shuttering including strutting, propping etc. and removal of form
6.30.1 Foundations, footings, bases of columns, etc. for mass concrete. 21.16 Sqm 156.275 3,307.00
6.30.3 Suspended floors, roofs, landings, balconies. 36.38 Sqm 208.069 7,570.00
Edges of slabs and breaks in floors and walls.
Under 20 cm wide.
Steel reinforcement for R.C.C. work, where not included in the complete rate of
RCC, including straightening, cutting, bending, placing in position, binding, wastage,
overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc.
complete in all respect below plinth level
HSR-21 Note:- Reinforcement shall be measured in length including hooks, if any,
6.33 separately for different diameters as actually used in work , excluding overlaps.
Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers
and annealed steel wire or other methods of binding & placing shall not be
measured and cost of these items shall be deemed to be included in the rates for
6.33.6 reinforcement.
Thermo-Mechanically Treated bars of grade Fe-500D or more. 747.73 Kg 60.724 45,405.00
HSR-21 Brick work with common burnt clay non-modular bricks of class designation 10.5 in
7.21 foundation and plinth in:.
7.21.1 Cement mortar 1:4 (1 cement: 4 coarse sand). 53.34 Cum 3,692.555 1,96,975.00
HSR-21 Half brick masonry with common burnt clay non-modular bricks of class designation
7.27 10.5 in foundations and plinth in:
7.27.2 Cement mortar 1 :4 ( 1 cement :4 coarse sand) 144.00 Sqm 458.109 65,968.00
Providing and laying Cement concrete flooring 1 :2:4 (1 cement : 2 coarse sand : 4
9 graded stone aggregate) finished with a floating coat of neat cement, including cement
slurry, but excluding the cost of nosing of steps etc. complete.
10.10.1 40 mm thick with 20 mm nominal size stone aggregate. 72.62 Sqm 267.900 19,456.00
Authorised Signatory Contractor BOQ Page No. 34 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
HSR-21 Providing a floating coat of 1.50 mm thick neat cement laid in one operation to the
10.14 topping.
11 12 mm cement plaster of mix :
11.5.3 1 : 4 (1 cement: 4 fine sand) 180.64 Sqm 83.942 15,163.00
12 15 mm cement plaster on the rough side of single or half brick wall of mix :
11.6.1 1 : 4 (1 cement: 4 fine sand) 152.00 Sqm 101.802 15,474.00
Earth work in excavation of foundation of structures as per drawing and technical
HSR-21 specification, including setting out, construction of shoring and bracing, removal of
15.1 stumps and other deleterious matter, dressing of sides and bottom and backfilling with
approved material as per clause 304 of MORT&H specifications Ordinary soil,
15.1.2 Mechanical Means
15.1.2.1 Depth up to 3 m 169.56 Cum 78.584 13,325.00
15.1.2.2 Depth 3 m to 6 m 60.76 Cum 89.300 5,426.00
Providing & fixing steel bar embedded plastic steps of size 263mm x 165mm of
orange colour, confirming to specification in pump chambers, manholes etc., having
HSR-21 minimum 3mm thick polypropylene polymer confirming to is:10910 encapsulated on
14 12mm dia ribbed steel bars per IS : 1786. The rate include cost of setting the same to 30.00 Each 298.262 8,948.00
correct lines and levels duly embedded in 1 :2:4 cement concrete including carriage,
loading, uploading, stacking, handling, re-handling etc., complete in all respect to the
satisfaction of Engineer-in-charge
Providing and fixing SFRC MANHOLE COVERS AND FRAMES MARKED WITH IS:
HSR-21 12592 including setting the same to correct lines and levels in 1 :3 cement sand mortar
21.93 over manhole including carriage loading unloading stacking handling re-handling etc.
complete in all respects to the satisfaction to the Engineer-in-charge.
21.93.1 Type:- Extra Heavy Duty Set (EHD-35) 560MM Clear Opening 8.00 Each 1,154.649 9,237.00
Constructing brick masonry road gully chamber 110x50x77.5 cm with bricks in
16 cement mortar 1 :4 (1 cement : 4 coarse sand) including 500x450 mm precast R.C.C.
horizontal grating with frame and vertical grating complete as per standard design
22.207.1 With common burnt clay non-modular bricks of class designation 10.5. 10.00 Each 5,459.802 54,598.00
Providing and fixing factory made precast RCC perforated drain covers, having
concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8
HSR-21 mm dia four Nos. longitudinal & 9 Nos. cross sectional T.M.T. hoop bars, including
33.5 providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding
with M.S. flats of size 50 mm x 1.6 mm complete, all as per direction of Engineer-in-
charge.
Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable
method prescribed in IS: 2800 (part I), including collecting samples from different strata,
18 preparing and submitting strata chart/ bore log, including hire & running charges of all
equipments, tools, plants & machineries required for the job, all complete as per direction
of Engineer-in-charge, up to 90 metre depth below ground level.
33.6.1 All type of soil
33.6.1.1 300 mm dia. 180.00 Rmt 510.796 91,943.00
Authorised Signatory Contractor BOQ Page No. 35 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable
method prescribed in IS: 2800 (part I), including collecting samples from different strata,
HSR-21 preparing and submitting strata chart/ bore log, including hire & running charges of all
33.7 equipments, tools, plants & machineries required for the job, all complete as per direction
of Engineer -in-charge, beyond 90 metre & up to 150 metre depth below ground
level.
33.7.1 All type of soil
33.7.1.1 300 mm dia. 120.00 Rmt 595.631 71,476.00
Supplying, assembling, lowering and fixing in vertical position in bore well,
HSR-21 Unplasticised PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818,
33.8 including required hire and labour charges, fittings & accessories etc. all complete, for all
depths, as per direction of Engineer -in-charge.
33.8.3 200 mm dia. 200.00 Rmt 919.790 1,83,958.00
Supplying, assembling, lowering and fixing in vertical position in bore well
HSR-21 Unplasticised PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818,
33.9 including hire & labour charges, fittings & accessories etc. all complete, for all depths, as
per direction of Engineer-in-charge.
33.9.3 200 mm dia. 100.00 Rmt 979.621 97,962.00
HSR-21 Supplying, filling, spreading & levelling stone boulders of size range 5 cm to 20 cm,
22 in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction 12.56 Cum 1,039.452 13,056.00
of Engineer-incharge.
Supplying, filling, spreading & levelling gravels of size range 5mm to 10 mm, in the
23 recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, 12.56 Cum 1,039.452 13,056.00
all complete as per direction of Engineer-in-charge
Supplying, filling, spreading & levelling coarse sand of size range 1.5 mm to 2 mm
24 in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as 12.56 Cum 1,039.452 13,056.00
per direction of Engineer -in-charge.
HSR-21 Gravel packing in tube well construction in accordance with IS: , including providing
25 gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all 11.78 Cum 1,166.258 13,733.00
complete as per direction of Engineer-in-charge.
HSR-21 Providing and fixing suitable size threaded mild steel cap or spot welded plate to
26 the top of bore well housing/ casing pipe, removable as per requirement, all complete for
bore well of:
33.16.3 200 mm dia. 2.00 Each 243.789 488.00
Providing and fixing suitable size threaded mild steel cap or spot welded plate to
27 the top of bore well housing/ casing pipe, removable as per requirement, all complete for
bore well of:
33.17.3 200 mm dia. 2.00 Each 1,358.253 2,717.00
HSR-21 Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe
33.18 assembly of tube well as per IS:2800 (part I).
33.18.3 200 mm dia. 2.00 Each 258.970 518.00
Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to
establish maximum rate of usable water yield without sand content (beyond permissible
limit), with required capacity air compressor, running the compressor for required time till
HSR-21 well is fully developed, measuring yield of well by "V'' notch method or any other
33.19 approved method, measuring static level & draw down etc. by step draw down method,
collecting water samples & getting tested in approved laboratory, i/c disinfection of tube
well, all complete, including hire & labour charges of air compressor, tools & accessories
etc., all as per requirement and direction of Engineer-in-charge.
TOTAL AMOUNT 12,40,310.00
TOTAL AMOUNT 12,40,310.00
Authorised Signatory Contractor BOQ Page No. 36 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
( WATER SUPPLY WITH SHALLOW TUBEWELL )
Sr. Basic
HSR No. Description of Item Qty. Unit Amount
No. Rate
(A) SHALLOW TUBEWELL WORK - AS PER HSR 2021
HSR-21 Drilling of 250mm dia of bore through bokky type instrument complete in all respect
20.90 including charges for shifting of infrastructures as per IS Code 12818: 1992.
20.90.1 0 to 50m BGL 50.00 Rmt 354.521 17,726.00
20.90.2 51 to 75m BGL 10.00 Rmt 404.529 4,045.00
HSR-21 Providing and Lowering 225 mm outer dia UPVC pipe threaded (10kg/CM2) duly
2 ISi marked IS Code 12818:1992 complete in all respect as per directions of Engineer-in- 50.00 Rmt 1,264.488 63,224.00
charge
HSR-21 Providing and lowering 225mm outer dia UPVC filter Jali (10 Kg/CM2) duly ISI
3 marked IS Code 12818:1992 complete in all respect as per directions of Engineer-in- 10.00 Rmt 121.448 1,214.00
charge
HSR-21 Providing and fixing 250 mm M.S. clamp as for suitable pipe with nut & bolt complete
20.93 in all respect as per directions of Engineer-in-charge
HSR-21 Providing and fixing UPVC cap for 225mm outer dia UPVC pipe (10kg/cm2) duly ISi
5 marked IS Code 12818:1992 complete in all respect as per directions of Engineer-in- 1.00 Each 708.149 708.00
charge
HSR-21 Development of tube well with pump of suitable rating to that full satisfaction and as
20.95 directed by the Engineer-in-charge.
Supplying erection, testing of fully automatic electric control panel board for
T/Wells in Pump Chamber consisting of MS sheet of thickness 14 gauge duly painted box
type floor mounted made of angle Frame containing 1 no. fully automatic air brake starter
suitable for Motor of the following capacity, Min switch of suitable range with HRC fuse, 1
HSR-21 no. volt meter (0 to 500 volts), 1 No. Amp. Meter of 0 to 100 amp. 3 sets of indicating
20.114 lamp capacitor of suitable capacity and 1 no. single phase preventers with the timer
switch including wiring in panel board and suitable electric energy meter wiring in Electric
Control Panel Board complete in all respect as per specification given in Schedule No. II,
Including MCB, suitable, Capacitor, Wooden Box etc as per site requirement complete in
all respect.
20.114.2 15 HP Motor 1.00 Each 17,392.961 17,393.00
Supplying, erection, testing and commissioning of submersible pumping sets as
HSR-21 per BIS SPECIFICATION No. 8034-1989 (as amended upto date for pumps) and IS 9283-
8 1979 (as amended upto date for motor) the pump motor sets should be capable of
pumping clear fresh cold water having characteristics as specified in Clause-4 of IS 8034-
1989 and Clause 4.1 of IS 9283-1979.
20.124.28 Flow rate - 450 LPM, Head - 90m, BHP - 15.00 (11 KW) 1.00 Each 55,787.496 55,787.00
Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal
HSR-21 stability for hot & cold water supply including all CPVC plain & brass threaded fittings This
22.87 includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling
& testing of joints complete as per direction of Engineer in Charge.
22.87.7 62.50 mm nominal inner dia Pipes 100.00 Rmt 1,228.768 1,22,877.00
HSR-21 Providing and fixing gun metal gate valve with C.I. wheel of approved quality
22.98 (screwed end):
22.98.6 65 mm nominal bore 1.00 Each 1,265.381 1,265.00
Authorised Signatory Contractor BOQ Page No. 37 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Supply and jointing three core submersible flat cables of approved make with bare
bunched copper conductor insulated and sheathed with PVC for submersible pump motors
11 /fountain lights etc with voltage grade 1100 volts marked with IS:694, 1990 including
cost of jointing, materials as well as carriage, loading, unloading etc. complete in all
respect up to the entire satisfaction of Engineer- in-Charge.
24.5.1.5 Submersible Copper Cable 3 Core 10 sqmm 100.00 Rmt 183.065 18,307.00
TOTAL AMOUNT 3,33,212.00
TOTAL AMOUNT 3,33,212.00
Authorised Signatory Contractor BOQ Page No. 38 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
( FURNITURE WORKS )
Description of Item Qty Unit Rate w/o GST Amount
1 1 MOOT COURT
JURY TABLE - 7500 x 900 x 750mm
Providing and Fixing of Jury Table fabricated out of 19mm/ 12mm/ 9mm thick
commercial ply, with table top comprising 1mm thick open pore wood grain laminate over
19mm thick commercial ply with Ivory Coast wood edging made to shape as per drawing
supported on 62mm thick vertical supports comprising of Hard wood members 38x38mm
with 12mm thick Commercial ply on both sides finished with 1mm thick open pore wood
1.1 1.1 grain laminate as per colour scheme. Front face of table shall be finished with 1mm thick 1.00 Each 70,626.000 70,626.00
laminate in 100mm strips The edges of vertical support shall be lipped with 12mm thick
Ivory coast wood made to profile as per drawing & to be finished in French Polish. All
exposed edges shall be lipped with Ivory Coast wood lipping. All exposed wood shall be
French Polished after proper surface preprartion as per manufacturer's specifications and
to the entire satisfaction of Engineer-in-charge / Architect complete in all respect and to
be manufactured strictly as per Drawing no. FR-02.
CLERK TABLE - 1350 x 750 x 750mm(H)
Providing and placing of Clerk Table fabricated out of 19mm/12mm/9mm thick
commercial ply, having 19 mm thick commercial ply table top laminated with 1.0mm thick
laminate and 4mm thick ivory coast wood lipping made to shape as per drawing & shall
be finished in French Polish with keyboard drawer made of 1.0mm thick laminate over
12mm thick commercial ply and white oak wood edging made to shape. The drawers shall
be fitted with drawer slides, handles, locks etc., shutters shall be fitted with self closing
hinges, magnetic catchers, handles, locks of approved make. Storage unit fabricated out
of 19mm thick commercial ply finished with 0.8mm thick laminate of approved make &
shade on internal surfaces, all exposed edges shall be lipped with ivory coast wood
lipping. External vertical surfaces of storage units as well as tables shall have 1.0mm
thick laminate, complete in all respect with accessories, all exposed wooden/veneer work
shall be finished in French Polish, complete in all respects and to be manufactured strictly
as per Drawing no. FR-02.
ADVOCATES TABLE - 3600 x 600 x 1050mm(H)
Providing and Fixing of Advocates Table fabricated out of 19mm/ 12mm/9mm thick
commercial ply, with table top comprising 1mm thick open pore wood grain laminate over
19mm thick commercial ply with Ivory Coast wood edging made to shape as per drawing
supported on 19mm thick commercial ply vertical supports finished both sides with 1mm
1.3 1.3 thick open pore wood grain laminate as per colour scheme. Front face and edges of table 1.00 Each 23,901.000 23,901.00
shall be finished with 1mm thick laminate in 100mm strips. All exposed edges shall be
lipped with Ivory coast wood lipping. All exposed wood shall be French Polished after
proper surface preprartion as per manufacturer's specifications and to the entire
satisfaction of Engineer-in-charge / Architect complete in all respect and to be
manufactured strictly as per Drawing no. FR-02.
Authorised Signatory Contractor BOQ Page No. 39 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
WITNESS BOX - 1200 x 1200 x 1350mm(H)
Providing and Fixing of Witness Box made of Ivory Coast wood Corner Balustrades
75mm x 75mm, 50mm x 50mm Balusters, 50mm x 75mm Handrail made to shape as per
drawing & to be finished with French Polish mounted on 150mm High wooden platform
1.4 1.4 made of 18mm thick Plywood mounted on 50mmx50mmx130mm high SS leveling feet. 2.00 Each 20,263.000 40,526.00
All exposed wood shall be French Polished after proper surface preprartion as per
manufacturer's specifications and to the entire satisfaction of Engineer-in-charge /
Architect complete in all respect and to be manufactured strictly as per Drawing no. FR-
SPECTATORS/STUDENTS SEATING
Providing and Fixing of Seating Bench comprising of Desk Top made of 25mm thick
commercial board finished with 1mm thick open pore wood grain laimnate on top and
0.8mm laminate on underside,, Seat and Seat Back made of Ivory Coast wooden planks
25mm x 100mm and 20mm x 50mm Ivory Coast wood edging made to shape as per
drawing fixed with screws of approriate length on Powder coated upto 40-60 microns MS
1.5 1.5 frame made of MS Angle/ MS Hollow pipe made to shape as per drawing fixed on floor
with MS base plate. All exposed wood shall be French Polished after proper surface
preprartion as per manufacturer's specifications and to the entire satisfaction of Engineer-
in-charge / Architect complete in all respect and to be manufactured strictly as per
Drawing no. FR-02.
(Note:-Contractor will show one full size sample and get approved from
Engineer-in-Charge.)
a a 3600 mm (L) x 750 (B) x 900mm(H) Seating Bench 216.00 Each 25,858.000 55,85,328.00
b b 3000 mm (L) x 750 (B) x 900mm(H) Seating Bench 40.00 Each 22,935.000 9,17,400.00
c c 2400 mm (L) x 750 (B) x 900mm(H) Seating Bench 74.00 Each 17,981.000 13,30,594.00
SPECTATORS/STUDENTS SEATING [ FRONT ROW ] - 3600 mm Long
Providing and Fixing of Front Row comprising of Desk Top made of 25mm thick
commercial board finished with 1mm thick open pore wood grain laimnate on top and
0.8mm laminate on underside, Front made of Ivory Coast wood batten 25mm x 100mm
and 20mm x 50mm Ivory Coast edging made to shape as per drawing fixed with screws
of approriate length on Powder coated upto 40-60 microns MS frame made of MS Angle/
MS Hollow pipe made to shape as per drawing on floor with MS base plate. All exposed
wood shall be French Polished after proper surface preprartion as per manufacturer's
specifications and to the entire satisfaction of Engineer-in-charge / Architect complete in
all respect and to be manufactured strictly as per Drawing no. FR-02.
(Note:-Contractor will show one full size sample and get approved from
Engineer-in-Charge.)
a a 3600 mm (L) x 300 (B) x 900mm(H) Front Row 46.00 Each 23,240.000 10,69,040.00
b b 3000 mm (L) x 300 (B) x 900mm(H) Front Row 20.00 Each 20,464.000 4,09,280.00
c c 2400 mm (L) x 300 (B) x 900mm(H) Front Row 10.00 Each 16,063.000 1,60,630.00
GRAND TOTAL 96,43,219.00
GRAND TOTAL 96,43,219.00
Authorised Signatory Contractor BOQ Page No. 40 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
DETAILED ESTIMATE FOR CONSTRUCTION OF TEACHING BLOCK - 3 AT CRSU, JIND, HARYANA
SCHEDULE NO.1 - HSR ITEMS ( ELECTRICAL INTERNAL)
Sr. Item of
Description Qty. Unit Rate w/o GST Amount
No. HSR21
Supplying, errection, testing of Exhaust fan (as per IS code 374) having a each
HSR-21 capacity of 45 cubic metre per minute complete with suitable G.I sheet ducting in
20.72 structure confirming to latest IS specifications complete in all respect to satisfaction of
Engineer-in-charge. Minimum Size of fan shall be 300 x 300 mm.
RUBBER MATTING
Providing and fixing of insulated robber matting suitable for 11 KV each installation 1 M x
2 2 M x 12 mm thick (IS code 15652-40091) as per specification complete and as per 6.00 Each 1,368.076 8,208.00
directions of Engineer-in-charge
G.O. SWITCH
HSR-21 Supply, erection, testing & commissioning of G.O. Switch two poles, with blade, pin 6
20.86 insulators operating handle with GI pipe 25 mm class B complete in all respects.
CT METER
Supply, erection, testing and commissioning of CT meter of standard make with cubical
HSR-21 meter box as per HVPNL specifications including 3 phase electrical meter 100/5 of
20.88 standard make approved by HVPNL including CT/PT of suitable rating complete in all
respect as per directions of Engineer-in-charge
Electric Panel For Terrace Pump
Supplying erection, testing of fully automatic electric control panel board for
Submersible Pump at Terrace consisting of MS sheet of thickness 14 gauge duly
painted box type floor mounted made of angle Frame containing 1 no. fully automatic air
brake starter suitable for Motor of the following capacity, Main switch of suitable range
HSR-21 with HRC fuse, 1 no. volt meter (0 to 500 volts), 1 No. Amp. Meter of O to 100 amp. 3
20.114 sets of indicating lamp capacitor of suitable capacity and 1 no. single phase preventers
with the timer switch including wiring in panel board and suitable electric energy meter
wiring in Electric Control Panel Board complete in all respect as per specification Including
MCB, suitable, Capacitor, MS Box etc as per site requirement complete in all respect.
Make:- L&T, SIEMENS, BCH, SCHNEIDER or equivalent.
20.114.1 10 HP Motor 1.00 Each 11,594.712 11,595.00
Wiring main and sub mains in two single core for phase and neutral wire and one
6 single core for earth wire PVC insulated Copper conductor cable 1100 Volts grade in PVC
Conduit etc as required.
23.3.6.1 1 run of Size 1.50 Sqmm(1/1.40mm) 11,940.00 Rmt 87.514 10,44,917.00
23.3.6.2 1 run of Size 2.50 12,000.00 Rmt 112.518 13,50,216.00
23.3.6.3 1 run of Size 4 Sqmm(1/2.24mm) 2,000.00 Rmt 143.773 2,87,546.00
23.3.6.4 1 run of Size 6 Sqmm(1/2.80mm) 2,000.00 Rmt 172.349 3,44,698.00
23.3.6.5 1 run of Size 10 Sqmm(1/3.50 mm) 2,000.00 Rmt 345.591 6,91,182.00
7 COPPER WIRING WITH MODULAR SWITCHES IN PVC CONDUIT
Wiring for Light/Fan/call bell point with modular type switch/socket and GI box,
23.4.1 Modular type face plate etc in 1.5 sqmm FRLS PVC insulated copper conductor cable in
1.6 mm thick PVC conduit pipe.
23.4.1.3 Group C 3,500.00 Each 709.935 24,84,773.00
Authorised Signatory Contractor BOQ Page No. 41 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
HSR-21 Wiring for Twin control light point with 2 nos , 2-ways, 5 amp. Modular switch
8 GI box and modular face plate in 1.5 sqmm FRLS PVC insulated copper conductor cable
in 1.6 mm thick PVC conduit pipe.
23.4.2.3 Group C 18.00 Each 921.576 16,588.00
HSR-21 Wiring for Light/Fan/call bell point in 1.5 sqmm FRLS PVC insulated copper
23.4.3 conductor cable in 1.6 mm thick PVC conduit pipe, without separate control switch.
23.4.3.3 Group C 248.00 Each 325.945 80,834.00
Wiring in PVC conduit system for 3-pin 5amp. Plug point by using 2 no 1.5 sqmm
HSR-21 FRLS copper wire and 1 no 1.5 Sqmm FRLS copper wire , including providing 1 no 5/6
23.4.4 Amp 3/5 pin Modular type socket and 1 no 5/6 Amp Modular type switch required GI Box
,modular face plate etc complete as required.
23.4.4.3 Group C 300.00 Each 934.971 2,80,491.00
Wiring in PVC conduit system for 3-pin 15amp. Plug point by using 2 no 4 sqmm
HSR-21 FRLS copper wire and 1 no 4 Sqmm FRLS copper wire for earthling , including providing 1
23.4.5 no 15/16 Amp 3/6 pin Modular socket and 1 no 15/16 Amp Modular switch required GI
Box , modular face plate etc complete as required.
23.4.5.3 Group C 591.00 Each 1,292.171 7,63,673.00
Supply and erection of PVC CONDUIT ISI marked (Medium) recessed in wall
HSR-21 /ceiling etc. including the cost of PVC bends, inspection boxes, iron
23.7.6 hooks and cement concrete etc. complete in all respect up to the entire satisfaction of
Engineer-in-Charge of work.
23.7.6.1 PVC pipe of 20 mm dia. 100.00 Rmt 25.897 2,590.00
23.7.6.2 PVC pipe of 25 mm dia. 9,680.00 Rmt 32.148 3,11,193.00
23.7.6.3 PVC pipe of 32 mm dia. 150.00 Rmt 44.650 6,698.00
23.7.6.4 PVC pipe of 40 mm dia. 150.00 Rmt 57.152 8,573.00
13 FITTING AND ACCESSORIES
Providing and fixing Piano type accessories of approved make in existing box and
23.8.1 Bakelite sheet including fixing and making necessary connections, complete in all
respect.
23.8.1.5 Ceiling rose flush/surface type. 115.00 Each 17.860 2,054.00
23.8.1.6 Call bell 220/230 volts musical type 30.00 Each 90.193 2,706.00
23.8.1.12 Bakelite angle/straight button holder large size. 563.00 Each 45.543 25,641.00
HSR-21 Supply and erection of suitable MS/GI Box covered with 5 mm thick Bakelite
23.8.3 sheet as below
75 mm x 75 mm x 60 mm deep M.S. box for telephone and inter-communication
system
Supply and erection of 10.5 cm dia M.S.Fan box including 8 mm dia 30 cm long M.S.
15 Road made into suitable suspension hook and erected in R.C.C. slab for the erection of 398.00 Each 94.658 37,674.00
fan complete with all labour and material required to complete the job. .
Providing and fixing GI concealed sheet metal boxes with inner and outer face plate
16 including concealing the box in wall and fixing in position with inner plate and face plate
with all labour and material required for the job complete in all respects.
23.8.10.1 1&2 Modules including combined plate for Telephone points & LAN Points 299.00 Each 92.872 27,769.00
23.8.10.2 3 Modules 20.00 Each 126.806 2,536.00
23.8.10.3 4 Modules 20.00 Each 140.201 2,804.00
23.8.10.4 6 Modules 20.00 Each 185.744 3,715.00
23.8.10.5 8 Modules 200.00 Each 233.073 46,615.00
Authorised Signatory Contractor BOQ Page No. 42 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
23.8.10.6 12 Modules 5.00 Each 282.188 1,411.00
HSR-21 Providing and fixing modular type accessories of approved make in existing box
23.8.11 including fixing and making necessary connections, complete in all respect.
23.8.11.1 5 amp 1 way switch 406.00 Each 41.078 16,678.00
23.8.11.2 5 amp 2 way switch 36.00 Each 74.119 2,668.00
23.8.11.3 15 amp 1 way switch 200.00 Each 82.156 16,431.00
23.8.11.4 5 amp Socket 1,006.00 Each 82.156 82,649.00
23.8.11.5 15 amp 6 pin Socket 200.00 Each 124.127 24,825.00
23.8.11.6 Bell Push 30.00 Each 76.798 2,304.00
23.8.11.7 step type Fan Regulator 2 modules 300 watt 398.00 Each 257.184 1,02,359.00
23.8.11.8 Telephone Socket outlet modular type 108.00 Each 75.012 8,101.00
23.8.11.9 TV Socket outlet modular type 2.00 Each 75.012 150.00
23.8.11.10 Blanking plate 50.00 Each 17.860 893.00
23.8.11.11 RJ 45 Computer DATA socket outlet for CAT 6 or CAT6e cable Modular type 200.00 Each 303.620 60,724.00
23.8.11.12 USB Charger, 1000mA, 5V, 1 Module 200.00 Each 303.620 60,724.00
23.8.11.13 32A D.P. Main Switch With Key Ring Tag 2 Module 120.00 Each 327.731 39,328.00
HSR-21 Supply and Fixing 3 mm thick Bakelite sheet cover on existing MS/PVC junction
23.8.12 box/tee etc including fixing with brass screws and washers.
Supplying,installation,testing and commissioning of Passive lnfrared(PIR) based
HSR-21 occupancy sensor , non regulating programmable type, suitable for connected load up
19 to 1 OAmp , for mounting height up to 2.8 metre and for 5 m diameter coverage area 50.00 Each 3,686.304 1,84,315.00
along with necessary fixing arrangements i/c programming at site etc. complete as
required.
HSR-21 Erection of exhaust fan in existing opening ,complete with necessary earthling of fan
23.9 including carriage from PWD store to the site of work.
Making suitable hole in the wall suitable for exhaust fan up to 450 mm sweep
21 including finishing the same and fixing of Stainless steel wire mesh 2 mm thick having 115.00 Each 381.311 43,851.00
about 50 meshes per inch at exhaust side complete as required
HSR-21 Providing and fixing outdoor duty Ply of 12 mm thick frame suitable for exhaust fan
23.12 up to 450 mm sweep etc complete as required
HSR-21 Supply and erection of sheet steel enclosures 1 pole/2 pole/4 pole on wall on
23.22.3 existing pedestal complete as required
23.22.3.2 S.P.N. or DP enclosure suitable for DP MCB 120.00 Each 356.307 42,757.00
23.22.3.3 TPN enclosure suitable for TP , TPN or FP MCB 4.00 Each 414.352 1,657.00
Supply and erection of double door sheet steel enclosure distribution board
HSR-21 suitable for MCBS and ELCBS etc. recessed in wall including bonding to earth with all
23.22.4 labour and material required to complete the job in all respect up to the entire
satisfaction of the Engineer-in-Charge of the work.
23.22.4.2 SPN DB Double Door 8 way 12.00 Each 1,405.582 16,867.00
23.22.4.5 TPN DB Horizontal type Double Door 4 way 3.00 Each 2,706.683 8,120.00
23.22.4.7 TPN DB Horizontal type Double Door 8 way 25.00 Each 3,957.776 98,944.00
23.22.4.11 Vertical TPN DB Double Door 8 way 6.00 Each 8,082.543 48,495.00
HSR-21 Supply and erection of miniature circuit Breaker 240/415 V in the existing
23.22.5 distribution board including making necessary connections:-
23.22.5.1 6 amp. to 32 amp single pole. 720.00 Each 144.666 1,04,160.00
23.22.5.4 40 amp. to 63 amp double pole. 25.00 Each 676.894 16,922.00
23.22.5.8 40 amp. to 63 amp. MCB's Four Pole. 36.00 Each 1,291.278 46,486.00
Authorised Signatory Contractor BOQ Page No. 43 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Supply and erection double pole/Four pole Residual (RCCB/ELCB) on 240/415V,
HSR-21 5Hz. AC supply installed in existing sheet steel enclosures including making necessary
23.22.6 connections and bonding to earth with all labour and material required to complete the
job in all respect up to the entire satisfaction of the Engineer-in-Charge of the work.
23.22.6.2 DP RCCB 30ma sensitivity , 40 A 12.00 Each 1,669.910 20,039.00
23.22.6.5 FP RCCB 30ma sensitivity, 40 A 2.00 Each 1,958.349 3,917.00
23.22.6.6 FP RCCB 30ma sensitivity, 63 A 30.00 Each 2,244.109 67,323.00
27 MISCELLANEOUS
Supply and erection of U- PVC Trunking/Channel of following size including cost
23.23.5 of fixing on wall, floor and ceiling etc. with required material complete the job in all
respect up to entire satisfaction of the Engineer-in-charge of work.
23.23.5.1 25x 12 mm 300.00 Rmt 21.432 6,430.00
23.23.5.2 38x 12 mm 300.00 Rmt 25.004 7,501.00
23.23.5.3 38x 25 mm 300.00 Rmt 46.436 13,931.00
23.23.5.4 50x 50 mm 300.00 Rmt 75.905 22,772.00
Supply and erection of MS cable tray , duly pained as required including erection of
23.23.6 the same on wall or ceiling with necessary fixture and other material required to complete
the job in all respect up to the entire satisfaction of Engineer-in Charge of the work.
23.23.6.1 MS perforated cable tray painted with powder coating 100 X 50 X2mm 500.00 Rmt 231.287 1,15,644.00
23.23.6.2 MS perforated cable tray painted with powder coating 200 X 50 X2mm 500.00 Rmt 350.949 1,75,475.00
Supply and erection of cable tray cover made of 1.25 mm thick GI sheet as
HSR-21 required including erection of the same on existing cable tray with necessary fixture and
23.23.7 other material required to complete the job in all respect up to the entire satisfaction of
Engineer-in Charge of the work.
23.23.7.1 GI cable tray Cover, suitable for cable tray of 100 X 50 X 2 mm 500.00 Rmt 202.711 1,01,356.00
23.23.7.2 GI cable tray Cover , suitable for cable tray of 200 X 50 X 2 mm 500.00 Rmt 340.233 1,70,117.00
HSR-21 Supplying and drawing of 1 no UTP 4 pair CAT 6 LAN Cable in the existing
23.23.9 surface/recess MS/PVC conduit as required.
Main LT PANEL NORMAL/Emergency Supply (1No:)
Supply, installation, testing and commissioning of load bank/LT Panel with digital
HSR-21 COST of incoming and outgoing MCCB's ) etc.suitable for operation of 240/415 volts AC.
23.24.4 Supply with both side cable allay, inter connection and fixing the same in existing MS
pedestal/wall complete withall labour and material required for the same up to the entire
satisfaction of Engineer-in-Charge of work.
23.24.4.3 Load Bank 4 way 400/800 amp. 1.00 Each 48,466.682 48,467.00
Additional Items for above Main LT Panel
Supply and erection of Modular case circuit breaker single pole/4 pole on existing
HSR-21 wall/pedestal/Panel including bounding to earth and making necessary connections
23.22.1 required to complete the job in all respect up to the entire satisfaction of the Engineer-in-
charge of the work.
23.22.1.12 4 pole MCCB 300 to 400 amp , 50 KA 4.00 Each 20,349.684 81,399.00
23.22.1.13 4 pole MCCB 600 to 800 Amp , 50 KA 1.00 Each 40,080.519 40,081.00
LT PANEL-1 NORMAL/ EMERGENCY SUPPLY (1No:)
Authorised Signatory Contractor BOQ Page No. 44 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Supply, installation, testing and commissioning of load bank/LT Panel with
HSR-21 EXLUDING COST of incoming and outgoing MCCB's ) etc.suitable for operation of 240/415
23.24.4 volts AC. Supply with both side cable allay, inter connection and fixing the same in
existing MS pedestal/wall complete withall labour and material required for the same up
to the entire satisfaction of Engineer-in-Charge of work.
23.24.4.2 Load Bank 8 way 400 amp.( 1 Incomer + 8 Outgoings ) 1.00 Each 56,620.665 56,621.00
Additional item to above LT Panel-1
Supply and erection of Modular case circuit breaker single pole/4 pole on existing
HSR-21 wall/pedestal/Panel including bounding to earth and making necessary connections
23.22.1 required to complete the job in all respect up to the entire satisfaction of the Engineer-in-
charge of the work.
23.22.1.9 4 pole MCCB 6 amp to 100 amp , 25 KA 6.00 Each 6,130.445 36,783.00
23.22.1.11 4 pole MCCB 200 to 250 amp, 25 KA 4.00 Each 10,808.872 43,235.00
23.22.1.12 4 pole MCCB 300 to 400 amp , 50 KA 1.00 Each 20,349.684 20,350.00
HSR 21 MCCB Enclosure made of Sheet Steel suitable for mounting MCCB of
23.22.2 following ratings
23.22.2.2 MCCB up to 250 A FP 2.00 Each 4,299.795 8,600.00
LT PANEL-2 NORMAL/ EMERGENCY SUPPLY (1No:)
Supply, installation, testing and commissioning of load bank/LT Panel with
HSR-21 EXLUDING COST of incoming and outgoing MCCB's ) etc.suitable for operation of 240/415
23.24.4 volts AC. Supply with both side cable allay, inter connection and fixing the same in
existing MS pedestal/wall complete withall labour and material required for the same up
to the entire satisfaction of Engineer-in-Charge of work.
23.24.4.2 Load Bank 8 way 400 amp 1.00 Each 56,620.665 56,621.00
Additional item to above LT Panel-2
Supply and erection of Modular case circuit breaker single pole/4 pole on existing
HSR-21 wall/pedestal/Panel including bounding to earth and making necessary connections
23.22.1 required to complete the job in all respect up to the entire satisfaction of the Engineer-in-
charge of the work.
23.22.1.9 4 pole MCCB 6 amp to 100 amp , 25 KA 5.00 Each 6,130.445 30,652.00
23.22.1.11 4 pole MCCB 200 to 250 amp, 25 KA 5.00 Each 10,808.872 54,044.00
23.22.1.12 4 pole MCCB 300 to 400 amp , 50 KA 1.00 Each 20,349.684 20,350.00
HSR-21 MCCB Enclosure made of Sheet Steel suitable for mounting MCCB of
23.22.2 following ratings
23.22.2.2 MCCB up to 250 A FP 2.00 Each 4,299.795 8,600.00
LOAD BANKS FOR LIGHTING & POWER DB'S DISTRIBUTION SUPPLY (4No:)+
SUPPLY DIDTRIBUTION TO EV CHARGING POINTS (1No)
Supply, installation, testing and commissioning of load bank/LT Panel with
HSR-21 EXLUDING COST of incoming and outgoing MCCB's ) etc.suitable for operation of 240/415
23.24.4 volts AC. Supply with both side cable allay, inter connection and fixing the same in
existing MS pedestal/wall complete withall labour and material required for the same up
to the entire satisfaction of Engineer-in-Charge of work.
23.24.4.2 Load Bank 8 way 250 amp. 5.00 Each 52,128.875 2,60,644.00
Additional item to above
Authorised Signatory Contractor BOQ Page No. 45 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Supply and erection of Modular case circuit breaker single pole/4 pole on existing
HSR-21 wall/pedestal/Panel including bounding to earth and making necessary connections
23.22.1 required to complete the job in all respect up to the entire satisfaction of the Engineer-in-
charge of the work.
23.22.1.9 4 pole MCCB 6 amp to 100 amp , 25 KA 40.00 Each 6,130.445 2,45,218.00
HSR-21 SITC Four pole ON LOAD Manual change over switch in SS enclosure of following
23.22.8 Ratings
23.22.8.5 400 amp 415 volts 1.00 Each 31,365.732 31,366.00
41 MS STAND, BUS BAR CHAMBER AND PANELS
Supply and erection of M.S. angle iron frame duly welded for housing M.S. sheet &
23.24.1 main switches etc. on it, fixed on wall by means of suitable size of rag bolts with cement 400.00 Kg 83.942 33,577.00
concrete, duly painted with three coats of approved paint including one coat of red oxide.(
LT Panel's Stand & Load Bank stand)
42 SAFETY ITEMS
Supply and erection of Medium Voltage caution notice plate of size 200 x 150 mm
in three languages.
43 Supply and erection of shock restoration chart in glass frame. 10.00 Each 261.649 2,616.00
Supply & Erection of mild steel bucket stand suitable for 6 Nos. fire buckets,(but
without bucket) including the cost of welding and painting of complete stand will one coat
44 of red oxide and 2 coats of approved paint of red colour with all labour and material 4.00 Set 2,738.831 10,955.00
required to complete the job in all respect up to the entire Satisfaction engineer in charge
of the work (size 6'x4' made of GI pipe 32mm dia).
45 Earthing
Earthing with GL earth pipe 4.5 m long and 40 mm dia with masonry enclosures on the
top etc. (but without charcoal or coke and salt) as required.
24.1.2 Extra for using salt and char coal/coke for pipe earth electrode as required 4.00 Each 651.890 2,608.00
Earthing with G.I. earth plate 600 mmx 600 mm x 6 mm thick including accessories
and providing masonry enclosures with cover plate having locking arrangement and
watering pipe etc. (but without charcoal or coke and salt) complete as required.( For 2No:
LT panels& DB's Elect Room 4)
Earthing with tinned copper earth plate 6D0mmx600mmx3mm thick including
accessories and providing masonry nclosures with cover plate having locking
arrangement and watering pipe etc. (but without charcoal or coke and salt) etc. complete
as required.
24.1.5 Extra for charcoal or coke and salt for G. I. plate or copper plate earth electrode. 42.00 Each 801.021 33,643.00
Supplying and laying 25mm x 3mm G.I. strip at 0.5 metre below ground as metre 53
strip earth electrode including soldering etc. as required.
Supplying and laying 25mm x 3 mm G.I. strip in 40 mm dia,GI pipe as/from earth
electrode including soldering etc. as required
Providing and fixing 25 mm x 3mm G.I. strip on surface or in recess for connections etc.
as required with all labour and material.
Providing and fixing 25 mm x5 mm copper strip in 40 mm dia G.I. pipe from earth
electrode as required.
Authorised Signatory Contractor BOQ Page No. 46 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Providing and fixing 25 mm x 5mm copper strip on surface or in recess for connections
etc. as required with all labour and material.
Providing and laying earth connections from earth electrode with 4.00 mm dia G.I. wire in
15 mm dia G.I. pipe from earth electrode as required.
Providing and fixing 4.00 mm dia G1. Wire on surface or in recess for loop earthing as
required.
Lightning Arresters
Supply and erection of 20mm x 3 mm thick GI, tape fixed with suitable G.I. staples of
same size.
Supply and erection of 25mm dia 1.5 metre long lightning GI. tube rod tapered into a
24.1.16 point at the top with 16cm x 16cm x 3mm thick G.I. base plate and necessary nuts and 8.00 Each 898.358 7,187.00
bolts with washers.
Providing and fixing testing joints made of 20mm x 3mm thick G.I. strips 125 mm long
with 4 nos. G.I. bolts and nuts with washers complete.
46 LT CABLES
Laying of underground cable 0. 75 metre below ground level covered with sand
and bricks including excavation and refilling of trenches.:-
24.2.2.2 16 Sq mm to 35 sqmm 2 to 4 Core. 2,000.00 Rmt 160.740 3,21,480.00
24.2.2.5 300 sqmm to 400 sqmm 3 to 3½ Core. 1,000.00 Rmt 185.744 1,85,744.00
24.2.5 Laying and fixing of cable on surface/ cable tray etc as required:-
24.2.5.2 16 Sq mm to 35 sqmm 2 to 4 Core. 1,400.00 Rmt 20.539 28,755.00
24.2.5.3 50 Sq mm to 150 sqmm 2 to 4 Core. 700.00 Rmt 31.255 21,879.00
24.2.5.5 300 sqmm to 400 sqmm 3 to 3½ Core. 300.00 Rmt 47.329 14,199.00
HSR-21 Supply and erection of suitable compression type brass cable glands for
24.2.7 underground Cable :-
24.2.7.2 10 sqmm to 16s qmm Cable 2 to 4 Core 50.00 Each 44.650 2,233.00
24.2.7.3 25 sqmm to 50 sqmm Cable 2 to 4 Core 50.00 Each 76.798 3,840.00
24.2.7.4 70 sqmm to 95 sqmm Cable 3 to 3½ Core 50.00 Each 103.588 5,179.00
24.2.7.7 300 sqmm to 400 sqmm Cable 3 to 3½ Core 20.00 Each 226.822 4,536.00
HSR-21 Supply and erection of aluminium lugs heavy duty including crimping etc. up to the
24.2.8 entire satisfaction of the Engineer-in-charge of the work .
24.2.8.4 16 sqmm 100.00 Each 8.037 804.00
24.2.8.6 35sqmm 100.00 Each 10.716 1,072.00
24.2.8.8 70sqmm 100.00 Each 19.646 1,965.00
24.2.8.15 400sqmm 50.00 Each 125.020 6,251.00
49 24.3 HT CABLE
Laying and erection of XLPE (E)II kv HT aluminium conductor armoured cable 1
24.3.1 metre below ground level with sand & bricks with all labour and material including digging
and refilling of trench as required
24.3.1.1 up to 120 sqmm 3 core XLPE Cable 250.00 Rmt 179.493 44,873.00
Supplying and making indoor cable end termination with heat shrinkable
24.3.3 jointing kit complete with all accessories including lugs suitable for following size of 3
core, XLPE aluminium conductor cable of 11 KV grade as required
24.3.3.1 70 to 120 sqmm 2.00 Each 7,149.358 14,299.00
Supplying and making outdoor cable end termination with heat shrinkable
24.3.4 jointing kit complete with all accessories including lugs suitable for following size of 3
core, XLPE aluminium conductor cable of 11 KV grade as required
24.3.4.1 70 to 120 sqmm 2.00 Each 11,516.128 23,032.00
50 STREET LIGHTING
Authorised Signatory Contractor BOQ Page No. 47 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Supply and erection of GI bracket made of 32 mm dia medium class GI pipe,
having 15 deg angle from horizontal, suitable for fixing on top of Street Light pole/Wall .
24.4.2.4 150 cm long, with 30 cm high suitable size pole cap. 20.00 Each 684.931 13,699.00
Supply and erection of 32mm dia metre 1.5 m long bracket (B-class)
making an angle of 10° to 15° with horizontal plane for mounting street light fitting fixing
24.4.3 of GI. bracket on wall with 2 nos. 32 mm x 3 mm thick M.S. clamps including cost of 14.00 Each 511.689 7,164.00
cutting, welding of G.I. pipe complete with cement sand mixture, bolts and nuts etc.
including necessary connections.
HSR-21 Erection of street light fitting on the pole including the cost of petty material required
24.4.4 (irrespective of height/length of bracket).
24.4.4.2 At Pole above 4.5 metres but up to the height of 7 metres. 20.00 Each 107.160 2,143.00
Supply and erection of Single Phase weather proof M.S. box of size 20 cm x 15 cm x 10
cm with hinged cover made of 2 mm thick MS sheet, locking arrangements, housed in
24.4.5 wall/fixed on pole , including the cost of 1 no 4 way 16 A Bakelite connector, 1 no. 6 amp 14.00 Each 571.520 8,001.00
SP MCB and 1 Nos. 16 amp. neutral links fixed on Bakelite sheet in the M.S. box including
painting and necessary connections.( For Flood Lights)
HSR-21 Supplying and embedding following dia G.I. pipe (medium class) in pole
52 collar/foundation (during casting) for cable entry including bending the pipe to the
required shape complete as required.
24.4.7.2 40 mm dia 50.00 Rmt 384.883 19,244.00
Supply and erection of Hot Dip Galvanized octagonal pole of 3mm thickness, with
base plate including cost of nut and bolts , earthing studs, Integral Cable termination
arrangement 5 mm thick Bakelite base plate on suitable welded MS/GI bracket 32 A four
way connector 2 no 1 O A SP MCB , end cover and all accessories as supplied by the
53 manufacture including Providing RCC foundation of M25 grade (1 Cement:1 Stone
aggregate: 2 Coarse sand) i/c excavation, steel reinforcement (Fe 500) @80 kg/cum of
concrete contents, concrete cover 50mm, anchor bolts etc. over a bed of PCC 1 :5: 1 O of
required dimensions for octagonal poles of various heights as per following specifications
complete in all respects and as per directions of Engineer-in-charge
7 Metre Long pole with top dia 75mm and bottom dia 150 mm with base plate of size
54 MISCELLANEOUS ITEMS
S/E mark double walled corrugated (DWC) HDPE, pipe 10 Kg/Cm2 ,laid 0.75 Metre
below ground level including digging and refilling of earth including cost of suitable size
24.5.2 socket/coupler for HOPE pipe including the cost of labour and material required to
complete the job in all respect up to the entire satisfaction of Engineer in charge of the
24.5.2.3 DWC/HDPE pipe 63/50 mm outer dia/inner dia 600.00 Rmt 124.127 74,476.00
24.5.2.5 DWC/HDPE pipe 120/105 mm outer dia/inner dia 500.00 Rmt 241.110 1,20,555.00
24.5.2.7 DWC/HDPE pipe 180/150 mm outer dia/inner dia 500.00 Rmt 342.912 1,71,456.00
55 RCC FOUNDATIONS FOR DG SET & TRANSFORMER
Providing RCC foundation of M20 grade (1 Cement:1.5 Stone aggregate: 3 Coarse sand)
i/c excavation, steel reinforcement (Fe 500) @ 50 kg/cum of concrete contents, concrete
HSR-21 cover 50mm, over a bed of 75mm thick PCC 1:5:10, of required dimensions as per OEM
24.7 recommendations to provide levelled surface for placement of the DG set complete in all
respects and as per directions of Engineer-in-charge (Size of foundation assumed =
24.7.6 300/400 KVA DG Set & 600KVA TRANSFORMER 2.00 Each 90,010.828 1,80,022.00
Authorised Signatory Contractor BOQ Page No. 48 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
GEYSERS
Providing and fixing in position best Indian make (to the approval of the engineer-in-
charge) storage type automatic electric water heater,
pressure/non-pressure type thermostatically controlled, suitable for operation on 230
volts, 50 cycles single phase vertical wall mounting fitted with-draw able and adjustable
type AC, thermostat. Thermostat knob to be readily accessible through the opening of
suitable cover for and adjustment of temperature in the installed position of heater and
HSR-21 the thermostat should be withdrawn without having to drain the water, electric heating
56 element made out of copper tube (heating element should be easily removed and
replaced in the installed position of heater) A neon indicator 1 AMP, inner container made
out of copper tinned both from inside and outside, outer container made out of mild steel
sheet finished in gleaming white stove enamel paint, insulated between the inner and
outer with fibre glass wool with 1 metre length of suitable capacity 3 core flexible cord
with plug and non return valve plastic/lead connections or pressure release valve (where
required). Complete including fixing and testing for a week (as required by Engineer-
22.216.5 incharge.
25 Litres capacity 5.00 Each 8,086.115 40,431.00
Constructing brick masonry inspection Chamber sizes as given below up to 0.60 metre
average depth in cement mortar 1 :5 lime concrete with 40 per cent lime mortar 2:3 in
foundation cement concrete 1 :2:4 benching 12mm thick cement plaster 1 :2 with a
57 21.84 floating coat of 1 mm thick of neat cement R.C.C. 1 :2:4 slab 100 mm thick/cement
concrete topping, 50mm thick: with 455mmx455mm / 455mm x610mm inside light duty
C.I. inspection chamber cover and frame weight as per 1.5.1. specification painted with 3
coats of black bitumastic superior paint complete as per standard design.
Size 450 mm X 600 mm inside (with 455 mm x 610 mm cover and frame single seal
pattern I weighing 38 kg with C.C. topping)
TRANSFORMERS/SUB STATION
Design, Supply & erection of 3phase copper wound distribution transformer 630 KVA
11/0.433 KVA rating outdoor type oil immersed naturally cooled as per Nigam
UHBVN-23
58 Specifications CSC-120 with amendments and relevent ISS with latest amendments. Any
other contingent thereto complete in all respect as per approved make and directions of
Engineer-in-charge as per respective capacity.
10.4 630 KVA 1.00 Each 10,86,586.000 10,86,586.00
11KV VCB VCB PANEL TO BE INSTALLED IN GIRLS HOSTEL SUB-STATION
11KV VCB Panels (Incoming, Outgoing & Capacitor Panels ) 25KA, 475MVA rupturing
UHBVN-23 capacity 24V DC operated indoor type with a set of CT,s PT,s KWH meter, relays,
-12.1 instruments etc complete in all respects confirming to Nigms Tech Specs and all relevent
ISS/IEC with latetest amendents
a Rating 1250A for incoming panel (Indoor Type ) 1.00 Each 3,93,813.557 3,93,814.00
b Rating 400A for outgoing panel (Indoor Type ) 5.00 Each 2,96,476.000 14,82,380.00
TOTAL RS. 170,09,674.00
Authorised Signatory Contractor BOQ Page No. 49 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
SCHEDULE NO.2 - FANS & FITTINGS & OTHER NS ITEMS
Code No. Description Qty. Unit Rate w/o GST Amount
SITC of recessed type 36W Full window glarefree opal Diffuser LED Panel of size
600X600mm suitable for recess with MS Powder coated White Housing. Ultra Slim recess
mounted EdgeLit LED module with high brightness LED package and Unique pattern
acrylic de-glaring diffuser sheet for glare free uniform light distribution suitable for
1 armstrong / grid ceiling. Total system Lumen of 36W LED should be 4100 or above in 1450 Each 3,407.000 4940150.00
Cool day Light(5600K to 6500K), Power factor>0.90, CRI (Ra) >80, THD <20% LED
Lamp. Efficacy>140 Lm/W. Complete with all accessories as required with connections
Make- Havells (STRATO2X2PLR36WLED830MOD), Phillips(RC380B LED36S-6500 G5
L60W60 PSU OD SG) , Bajaj(BCTBLR 36W LED FP CW) / CGL or equivalent.
SITC of LED Surface Mounted Square/Rect. Bulkhead Light. The Fixture should be
NS Made of PDC Housing.PF>.95, System Wattage 10w with Minium 100 lumens/W in 5700k.
2 The Fixture should be IP-65of Makes :-PHILIPS(WT202W LED6S NW PSU S2 PC)/ 24 Each 1,255.000 30120.00
BAJAJ(112334-BIBWP 10W LED) /CGL: LBHN-10-CDL/GE/OSRAM/WIPRO/Havells) or
equivalent.
SITC Surface Mounted Bracket/wall light . The Fixture should be Made of
NS chrome&metal Housing.PF>.95, System Wattage 10Ww with Minium 1500 lumens in
3 5700k. The Fixture should be of Makes :-BAJAJ (BCLSB10NW) / HAVELLS 563 Each 468.000 263484.00
(LUMILINEBS10WLED 865 SPC WH / CGL (CCS-103-10-65-SL-DP-NWH)/GE/OSRAM
/WIPRO/PHILIPS or equivalent.
SITC 45W LED Street Light. The Fixture should be Made of pressure diecast housing
with TOUGHNED GLASS diffuser and indivisual LEDs with secondary optics with IP 66
NS protection. PF>.95, System Wattage LED 45W with Minium 1500 lumens in 5700k. The
E-4 Fixture should be of Makes :-BAJAJ EDGE (ENXT P 45L WW CR PC SD) /PHILIPS BRP 052
LED 045 CW SLMR FG S1 PSU GR/CGL LSTP-45 CDL /GE/OSRAM/WIPRO/Havells or
equivalent.
SITC 1x18W or 18/20W LED 1200mm Batten Light. The Endura Fixture is a surface
& wall mounted LED batten with extruded aluminium housing and robust construction .
NS PF>.95, System Wattage LED 20W with Minium 1500 lumens in 5700k. The Fixture
E-5 should be of Makes :-PHILIPS ( BN308C LED20S-6500 L120 PSU WH)/BAJAJ(BCLABSP22L
LED CW PC SD) /GE/OSRAM/CGL/Havells ( LUMILINE SMART 20W LED 865PC WH) or
equivalent.
SITC 5/6/9W LED aesthetically brillient surface picture/mirror light. The Fixture
NS comprises of aluminium /policarbonate . PF>.95, System Wattage LED 5/6/9W with
6 Minium 100 lumens/W in 5700k . The Fixture should be of Makes :-BAJAJ(BCLSB 05 NW) 95 Each 371.000 35245.00
/Havells(LUMILINE BS 9W LED 865 SPC WH) /CGL(CCS-103-05-65-SL-DP=NWH)/
GE/OSRAM/ PHILIPS etc.) or equivalent.
Supply, erection, testing and commissionoing of 30 KVA UPS (3-3) system
complete with battery bank (30/60 minutes backup) SMF battery 12 V 65 AH/12V120AH
NS = 32 Nos. complete with all accessories including battery breaker, racks, links, cabling
E-7 including all petty material required to complete the job upto entire satisfaction of the
Engineer-in-charge. Make: APC Model G-300 UPS complete specifications attached or
equivalent .
NS Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper
8 conductor PE insulated, shielded with fine tinned copper braid and protected with PVC 250 Rmt 33.000 8250.00
sheath in the existing surface/ recessed steel/ PVC conduit as required.
9 LT & HT CABLES
LT CABLES
Authorised Signatory Contractor BOQ Page No. 50 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
SUPPLY OF PVC/XLPE INSULATED ARMOURED CABLES
Supply of aluminium onductor PVC/XLPE insulated PVC sheathed armoured and served
cable 1100 volts grade as per IS:7098 (Part-1)1988. Make Havells,Polycab,Finolex,KEI or
equivalent.
i Overall size 35sq.mm (3½ Core) Armoured 1400 Rmt 347.000 485800.00
ii Overall size70sq.mm (3½ Core) Armoured 700 Rmt 619.000 433300.00
iii Overall size 400sq.mm (3½ Core) Armoured 1600 Rmt 2,867.000 4587200.00
iv Overall size 16sq.mm (4Core) Armoured 2000 Rmt 203.000 406000.00
SUPPLY OF FLEXIBLE PVC INSULATED MULTICORE FRLS PVC SHEATHED
MULTISTRANDED CABLES WITH BRIGHT ANNEALED
ELECTROLYTIC BARE COPPER CONDUCTOR FOR VOLTAGE GRADE UPTO 1100 V
CONFORMING TO IS-694:2010. SIZE-2x1.5Sq mm(30/0.25)
HT CABLES
STRANDED COMPACT CIRCULAR ALUMINIUM CONDUCTOR, CONDUCTOR SCREEN
WITH EXTRUDED SEMI CONDUCTING COMPOUND, , XLPE INSULATED , INSULATION
SCREENING WITH EXTRUDED SEMI CONDUCTING COMPOUND IN COMBINATION WITH
i COPPER TAPE, CORES LAID UP, INNERSHEATH OF PVC, GALVANISED STEEL FLAT STRIP 250 Mtr. 935.000 233750.00
ARMOURED , AND OVERALL PVC SHEATHED CABLE CONFORMING TO IS 7098 (PART-2)
2011 WITH UPTO DATE AMENDMENTS.
Overall size 70 sq.mm (3 Core)
SITC of 36/40W LED 1200mm Suspension (Pendant) luminaires with efficient
Diffuser ensuring perfectly uniform illumination, ensured optimised and unparalleled light
distribution. Inter-connectable luminaires for aesthetically appealing downlight
NS application. The Fixture should be Made of Extruded Aluminium Housing. Inbuilt
E-10 Protection of 2kv, PF>.95, System Wattage 36/40W integral housing for driver. Minium
100 lumens/W in 5700k. The Fixture should be of Makes BAJAJ(BPCS 40 W LED 4F WH)/
PHILIPS-(SP095V LED40S 865 W7L120 PSU WH) / CGL: LCLP54-36-CDL / OSRAM/ GE/
WIPRO/ Havells(DESTG250LP/S36WLED840SWH1130) or equivalent.
SITC of 18W LED Surface mounted round/square type downlighter. The Fixture
should be Made of Extruded Aluminium Housing. Inbuilt Protection of 2kv, PF>.95,
11 System Wattage 18W integral housing for driver. Minium 100 lumens/W in 5700k. The 102 Each 921.000 93942.00
Fixture should be of Makes BAJAJ(BGSLO-SLEEK-18W RD)/ PHILIPS-SM200C LED15S
4000 PSU OD WH/ CGL: LCDSPL-S-18-CDL/OSRAM/GE/WIPRO/Havells or equivalent.
SITC 150W LED Flood Light. The Fixture should be Made of pressure diecast housing
with TOUGHNED GLASS diffuser and indivisual LEDs with secondary optics with IP 66
NS protection. PF>.95, System Wattage LED 150W with Minium 1500 lumens in 5700k. The
E-12 Fixture should be of Makes :-BAJAJ AMAZE LED (BJFL 150W LED I WW) /PHILIPS /CGL
PLUTO NEO (LFLN-150-WW/60-M) /GE/OSRAM/WIPRO/Havells JETA IRIS
(JETAIRISFL150WLED757ARNBLTG) or equivalent.
AMF PANEL
Authorised Signatory Contractor BOQ Page No. 51 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Supplying , installation, testing & Commissioning of AMF Panel for 600KVA
Transformer & 300 KVA DG set having 2No1000A FP ELECTRICALLY OPERATED
NS DRAWOUT TYPE AIR CIRCUIT BREAKER(ACB) WITH MICROPROCESSOR BASED RELEASE
E-13 FOR O/C S/C E/F RELEASES AND OTHER STD ACCESSORIES as incomer alongwith
associated control equipments with control wiring etc etc as per directions of Engineer in-
charge.
EV CHARGER
NS SITC of AC X2 7/7.4 KW/32AType-2 EV Charger
E-14 With a LCD screen, RFID, Appbased booking, 4G sim, OCPP enabled
NS SITC of water cooler of fully SS 150Ltr storage and 150Ltrs cooling per hour Model
E-15 SDLX150150 .
16 SITC of Aquaguard RO Prima100B 24 Each 83,991.000 2015784.00
AUTOMATIC VOLTAGE STABLIZER 10 KVA RATING
Supply and erection of Single phase copper wound Automatic voltage stablizer
of suitable capacity electronically controlled circuit with input voltage 140-260 volts
single phase AC supply and output voltage 220 ± 5% volts single phase AC supply having
NS main silicon core copper wound step up transformer with suitable nos. of turns on primary
E-17 side and secondary side the transformer should be fully insulated inside the MS sheet box
of suitable size. There should be power control relay and single pole MCB (C-curve, 10kA)
of suitable capacity complete with internal copper wiring along with amp. meter and volt
meter, high voltage cut off 280 volt input (240 volt output) and 90 volt maximum boost
and overloading protection to be provided:-
Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star
rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3
nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper
winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air
NS delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less
E-18 than 10%, with electronic regulator unit for speed control and all remaining accessories
including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation
resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply,
earthing etc. complete as required.
Make Atomberg,Crompton,Havells
Authorised Signatory Contractor BOQ Page No. 52 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Providing and fixing in position best Indian make Instant type 3 Litres capacity
automatic electric water heater, pressure/non-pressure type thermostatically controlled,
suitable for operation on 230 volts, 50 cycles single phase vertical wall mounting fitted
with-draw able and adjustable type AC, thermostat. Thermostat knob to be readily
accessible through the opening of suitable cover for and adjustment of temperature in the
installed position of heater and the thermostat should be withdrawn without having to
NS drain the water, electric heating element made out of copper tube (heating element
E-19 should be easily removed and replaced in the installed position of heater) A neon indicator
1 AMP, inner container made out of copper tinned both from inside and outside, outer
container made out of mild steel sheet finished in gleaming white stove enamel paint,
insulated between the inner and outer with fibre glass wool with 1 metre length of
suitable capacity 3 core flexible cord with plug and non return valve plastic/lead
connections or pressure release valve (where required), Complete including fixing and
testing for a week (as required by Engineer-incharge.
NS Providing , Laying & commissioning in position 4core FRP 5.8MM UNARMEND –FINOLEX or
E-20 Equivalent Fiber Optic cable.
NS Providing , fixing & commissioning in position SC-SC/SIMPLEX/SM Patch Chord 3M D-
E-21 Link or Equivalent
NS Providing , fixing & commissioning in position SC-SC/SIMPLEX/SM Patch Chord 1M D-
E-22 Link or Equivalent
NS Providing , Laying & commissioning in position 24core FRP 5.8MM ARMOURED –FINOLEX
E-23 or Equivalent Fiber Optic cable.
SITC Siemens/CGL/C&S/ABB make 11KV indoor SF6 Insulated Ring Main Unit(RMU),
NS 630Amp/800A,21KA, 3-way, extensible having 2 no.load break switch & 1 nos. VCBs,
E-24 manual withself powered IDMT relay & ring core CT complete in all respect for feeding
600KVA Transformer.
RACEWAYS
NS SITC of Metal/GI Raceways having 2.44 mtr standered length size 225x38x 3
E-25(i) compartments 1.6mm thick. Legrand code 6895-04 or equivalent.
NS SITC of Metal/GI Raceways having 2.44 mtr standered length size 100x38x 1
E-25(ii) compartments 1.6mm thick. Legrand code 6895-02 or equivalent.
NS SITC of Metal/GI Raceways having 2.44 mtr standered length size 50x38x 1
E-25(iii) compartments 1.6mm thick . Legrand code 6895-00 or equivalent.
NS SITC of Fixing brackets for 225x38mm 3 compartment 1.6mm thick raceways Legrand
E-25(iv) Code 6897-25 or equivalent.
NS SITC of Fixing brackets for 100x38mm 1 compartment 1.6mm thick raceways Legrand
E-25(v) Code 6897-37 or equivalent.
NS SITC of Fixing brackets for 50x38mm 1 compartment 1.6mm thick raceways Legrand
E-25(vi) Code 6897-27 or equivalent.
SITC of Vertical Riser for 225mm width raceways Legrand Code-6897-23 or equivalent. 50.00 Each 1,584.000 79200.00
SITC of coupler for joining raceways Legrand Code- 6897-77 or equivalent. 50.00 Each 123.000 6150.00
E-25(viii)
NS SITC of Height Adjustable Junction Box with lid size 225x225x60-90mm Legrand Code
Authorised Signatory Contractor BOQ Page No. 53 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Supply ,Installation,Testing & Commissioning of 200KVAR / 415V SecuRite APFC Panel
CYCAP indoor installation with necessary protections as per Havells Price List 1-3-203 Cat
26 E-26 1.00 Each 6,02,789.000 602789.00
No:-QHKTCB5200X0 (200 kVAr / 415 V SecuRite APFC Panel CYCAP) (Make: Havells,
L&T. or equivalent) 200 kVAr (5,5,5,10,25,50,50,50) MCCB 400A 35 KA
SITC of 320 kVA (DG set Model KG4-320WS) Prime Duty (as per ISO 8528-1), 415 Volt,
Radiator Cooled, Silent Type with acoustic enclosure as per CPCB+ approved design,
Diesel generating set powered with prime duty Kirloskar Engine model 6SL90 ETA 4G3
having 380 BHP@1500 rpm having Class G3 governing along with base frame, Alternator
(capable of delivering electrical output of 256 kW output @ 0.8 power factor 40 deg C ,
27 E-27 50 Hz, 415 V, Class H insulation),Static Excitation System, Lube Oil Syste Microprocessor 1.00 Each 26,97,739.000 2697739.00
based Genset Controller as per standard design, AVM pads, 02 Nos 12 Volt Lead Acid
type Battery with Copper leads suitable for 3 consecutive starts, Silencer as per approved
design with bellow/s, inbuilt Day oil tank of approx 600 liters capacity as per standard
design, terminal arrangements including cable termination box suitable for terminating of
recommended size Al cable with all other associated items
TOTAL RS. 278,75,838.00
Authorised Signatory Contractor BOQ Page No. 54 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
SCHEDULE-3 (NON SCHEDULE ITEMS LIFT SYSTEM )
Code No. Description Qty. Unit Rate w/o GST Total Price
Supply Installation testing & commissioning of Passenger (1020 Kg, 15 persons.) Machine
NS Room Less Gearless Elevator with 3 year free comprehensivie warranty cum maintainance
LT-1 period to be supplied and installed in accordance with the following technical
specifications:
Reference Quotation:- OTIS (Model:-GeN2-Nova MRL)
CAPACITY (kgs) 1020 Kg, 15 persons. SPEED (mps) 1/1.25 mps. RISE (m) 27.00 M.
STOPS 6 Stops With (all opening on the same side). CONTROLLER TYPE ACD3-MRL.
DRIVE VF Regenerative (Closed Loop). POWER SUPPLY 400/415 Volts (3 Phase AC).
OPERATION Full collective operation. CAR GROUP One car (simplex)
MACHINE PM Gearless (Located above shaft). TRACTION MEDIA Flat Coated. Steel Belt.
CAR FINISH "• Rear Mid Panel = Stainless Steel #4(Hairline). • Rear Corner Panels =
Stainless Steel #4(Hairline). • Side Panels = Stainless Steel #4(Hairline). • Front Panels
= Stainless Steel #4(Hairline). FALSE CEILING TYPE CD-41. FLASE CEILING FINISH
Stainless Steel #4(Hairline). VENTILLATION Cross flow fan. HAND RAILS Stainless Steel
Mirror Finish. Handrails on all car panels(sideLH,sideRH&Rear). FLOORING: Provision of
Granite Flooring. CAR DOOR FINISH Stainless Steel #4(Hairline). LANDING DOORS
FINISH Stainless Steel #4(Hairline). HOISTWAY DIMENSIONS AVAILABLE (W x D –
mm)2550 mm W x 2050 mm D. CAR DIMENSIONS (W x D x H - mm) 1500 mm W x 1600
mm D x 2200 mm D. CAR & HOISTWAY DOOR TYPE Central opening (CO) doors. DOOR
OPENING (W x H - mm) 900 mm W x 2000 mm H. DOOR OPERATOR DC Door Operator.
Supply Installation testing & commissioning of Goods Lift (2000 Kg, ) Machine Room Less
NS Gearless Elevator with 3 year free warranty cum maintainance period to be supplied and
LT-2 installed in accordance with the following technical specifications:
Reference Quotation:- OTIS (Model:-GeN2-Nova MRL)
CAPACITY (kgs) 2000 Kg, . SPEED (mps) 0.55/0.66 mps. RISE (m) 27.00 M. STOPS 6
Stops With (all opening on the same side). CONTROLLER TYPE ACD3-MRL. DRIVE VF
Regenerative (Closed Loop). POWER SUPPLY 400/415 Volts (3 Phase AC). OPERATION
Full collective operation. CAR GROUP One car (simplex)
MACHINE PM Gearless (Located above shaft). TRACTION MEDIA Flat Coated. Steel Belt.
CAR FINISH "• Rear Mid Panel = Stainless Steel #4(Hairline). • Rear Corner Panels =
Stainless Steel #4(Hairline). • Side Panels = Stainless Steel #4(Hairline). • Front Panels
= Stainless Steel #4(Hairline). FALSE CEILING TYPE CD-41. FLASE CEILING FINISH
Stainless Steel #4(Hairline). VENTILLATION Cross flow fan. HAND RAILS Stainless Steel
Mirror Finish. Handrails on all car panels(sideLH,sideRH&Rear). FLOORING: Provision of
Granite Flooring. CAR DOOR FINISH Stainless Steel #4(Hairline). LANDING DOORS
FINISH Stainless Steel #4(Hairline). HOISTWAY DIMENSIONS AVAILABLE (W x D – mm)
2700MM Wide X 3000MM Deep D. CAR DIMENSIONS (W x D x H - mm) 1700MM Wide X
2500 MM Deep X 2200 MM High INSIDE DIMENSIONS D. CAR & HOISTWAY DOOR TYPE
Central opening (CO) doors. DOOR OPENING (W x H - mm) 1500 MM WIDE X 2000 MM
HIGH. DOOR OPERATOR DC Door Operator.
TOTAL RS. 103,29,090.00
Authorised Signatory Contractor BOQ Page No. 55 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
SCHEDULE-4 Provision of PA System
ITMES QTY Unit Rate w/o GST AMOUNT
SITC of 6W Recessed Ceiling speakers with following features:-Speaker Drive 6",
NS Complete Aluminium grille and Metal baffle, line matching transformer 100/70V line.
1 Variable wattage tappings of 6 / 3 / 1.5, Effective frequency range 110-15kHz (BS6840), 90.00 Each 3,426.000 3,08,340.00
SPL@1m/1W=91dB, Peak SPL 97dB complete with necessary mounting hardware &
accesories.
SITC of 10W Wall Mount Speaker with Frequency Response 150Hz - 15kHz, with Line
NS Matching transformer 100V. Variable tapping 10W/5W, SPL@1M/1W - 90dB, Peak SPL
PA-2 98dB. the cost of petty material required to complete the work upto the entire
satisfaction of Engineer In Charge.
Supply, Installation,Testing & Commissioning of Digital Voice Evacuation system
for 8 Zones. The System shall meet the standards of BS EN54 - 32 & EN 60849. it
should be capable for the EVAC, Paging, PA and BGM functions. The Controller shall have
SD card option to store the EVAC and Alert Voice Message. The Controller shall have
NS Speaker line supervision and amplifier auto changeover. The Controller shall have
PA-3 following features: Seperate Zone volume control at the front side of panel, Status
indications on the Panel for EVAC,Fault ,AC,DC ,Fault,ALERT & Fireman mic, Zone capacity
up to 96 Zones, 8 programmable Control Input and output, Fireman Microphone with High
Priority, THD<1%, Frequency response 80Hz - 20kHz, Up to 1000 Record files, 100V
Class-AB Speaker Output.
NS SITC of Remote Paging microphone with minimum 08 buttons and Busy/Hole
PA-4 Indication. The Microphone Should be suitable for Desktop mounting.
Supply Installation testing and comisioning of 480W RMS Dual Channel Power
Amplifier with Switch power technology for power electricity saving, Separate PFC
NS Design for highest reliability, Separate Power Supply System. Amplifier shall have
PA-5 Following Features: 240W RMS per Channel, Amplifier Output 100V, Supply input AC 220
+/- 10% - 50/60Hz, Short Circuit, Power, Tempreature, Overload Protection, Auto Cooling
Fans. THD <0.1%, Frequency Response 40Hz - 20kHz, AC & DC Fuse, SNR >89dB.
NS Supply Installation testing and comisioning of Professional CD/DVD player with
PA-6 USB flash port & 19" Rack mount arrangement.
NS Supply Installation testing and comisioning of 19-inch Equipment Rack with
7 standardized frame or enclosure for mounting multiple PA controllers, CD player, 2.00 Each 21,411.000 42,822.00
Amplifiers etc modules. Size 24U.
NS Supply & Laying of 1.5 sq.mm. multistrand PVC sheathed Two Core Twin Twisted
8 Speaker Cable in Exiting PVC Conduit. (HSR Item 2or Equivalent3.3.6 included in 1.00 Rmt 74.000 74.00
Electrical EI)
TOTAL RS. 12,31,108.00
Authorised Signatory Contractor BOQ Page No. 56 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
SCHEDULE-5 (Fire Alarm - Addresable System)
Description Qty. Unit Rate w/o GST Amount
Supplying, installation, testing and commissioning of micro processor based
intelligent addressable main fire alarm panel, central processing unit with the
following loop modules and capable of supporting not less than 240 devices (including
detectors) and minimum 120 detectors per loop and loop length up to 2 km, network
communication card, minimum 320 character graphics/ LCD display with touch screen or
other keypad and minimum 4000 events history log in the non volatile memory (EPROM),
power supply unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance
free batteries with automatic charger. The panel shall have facility to connect printer to
printout log and facility to have seamless integration with analog/digital voice evacuation
complete with all accessories . The panel shall be compatible for IBMS system with open
protocol BACnet/ Modbus over IP complete as per specifications.
17.2.1.1 Ten Loop Panel. 2.00 Each 4,06,791.862 8,13,584.00
NS Supplying, installation, testing & commissioning of central graphical fire alarm
2 management system to centrally monitor and operate the fire alarm system complete 2.00 Each 1,79,145.623 3,58,291.00
as required.
NS Supplying, installation, testing & commissioning of repeater panel wih 320 character/
3 Touch screen LCD display with inbuilt reset, acknowledge and silence switches 2.00 Each 97,058.384 1,94,117.00
complete as required.
NS Supplying, installation, testing & commissioning of intelligent analog addressable
FA-4 photothermal detector complete with mounting base complete as required.(40X6=240)
Supplying, installation, testing & commissioning of response indicator on
5 surface/recessed MS Box having two LED, metallic cover complete with all 12.00 Each 246.468 2,958.00
connections etc as required.
NS Supplying, installation, testing & commisssioning of intelligent addressable
FA-6 programmable sounder complete as required.
NS Supplying, installation, testing & commissioning of fault isolator complete with base as
FA-7 required.
NS Supplying, installation, testing & commissioning of intelligent aspiration detector for
FA-8 area coverage of minimum 5000 sq. ft. complete as required.
Supplying, installation, testing & commissioning of intelligent addressable thermal
9 detector with rate of rise cum fixed tempreature thermistor complete with base as 12.00 Each 2,434.318 29,212.00
required.
NS Supplying, installation, testing & commissioning of addressable fire control module
FA-10 complete as required.
NS Supplying, installation, testing & commissioning of addressable phone control module
FA-11 complete as required.
Supplying, installation, testing & commissioning of addressable beam detector with
NS short circuit isolator (inbuilt or seperate) complete with emitter and receiver including
FA-12 connections with remote test features etc complete as
required.
NS Supplying, installation, testing & commissioning of intelligent addressable duct
FA-13 detector including suitable Photo detector complete with base as required.
NS Supplying, installation, testing & commissioning of addressable manual call point
FA-14 complete as required.
NS Supplying, installation, testing & commissioning of addressable horn cum strobe
FA-15 complete as required.
Authorised Signatory Contractor BOQ Page No. 57 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
NS Supplying, installation, testing & commissioning of addressable strobe complete as
FA-16 required.
NS Supplying, installation, testing & commissioning of fire fighter telephone handset
FA-17 complete as required.
NS Supplying, installation, testing & commissioning of intelligent interface unit BACnet/
18 Modbus protocol i.e. supplying communication links between building management 2.00 Each 1,67,655.392 3,35,311.00
system and fire alarm control panel complete as required.
NS Supplying, installation, testing & commissioning of fire fighter phone jack complete as
FA-19 required.
Supplying & laying of 2x1.5 sqmm fire alarm armoured cable, 600/1000V rated with
20 annealed copper conductor having XLPE insulation, steel wire armouring & FRLS outer 1,500.00 Rmt 154.489 2,31,734.00
sheath complete as required.
NS Supplying and drawing of cable Fire Retardant PVC insulated copper conductor
21 cable in the existing surface / recessed steel conduit of following pairs, cores and size
including connections and interconnections etc. as required.
17.5.3.1 Speaker cable Single pair, 2-core, 1.5 sqmm 1,500.00 Rmt 48.222 72,333.00
17.5.3.2 Speaker cable Two pair, 2-core, 1.5 sqmm 1,500.00 Rmt 79.477 1,19,216.00
NS Supplying and fixing 25 mm dia MS flexible pipe with PVC
22 coating along with all ancillaries and accessories like coupler 100.00 Rmt 47.329 4,733.00
etc. as required.
NS Supplying and fixing of following sizes of steel conduit along with accessories in
23 surface/recess including painting in case of surface conduit, or cutting the wall and
making good the same in case of recessed conduit as required.
1.20.2 25 mm 1,000.00 Rmt 228.608 2,28,608.00
TOTAL RS. 41,51,950.00
Authorised Signatory Contractor BOQ Page No. 58 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
SCHEDULE-6 (HVAC SYSTEM)
Code Description QTY. Unit Rate w/o GST Amount
Variable Refrigerant Volume System
Supply Installation Testing and Commissioning of modular type Variable Refrigerant
Flow/Variable Refrigerant Volume air cooled Outdoor Units suitable for cooling and heating
, having all hermetically sealed inverter type Scroll Compressor(s), minimum two
compressors for above 14 HP modules ,microprocessor based controller, Top discharge
NS type condensing units with R410 A refrigerant , vibration isolators with suitable
HV-1 foundation etc. complete as required . The compressor and VRF should be of same make.
The outdoor should deliver 100% capacity at 39 Deg C . The unit shall deliver the rated
capacity at AHRI conditions and work even at 53 Deg C ambient temperature without
tripping. The unit shall be suitable to work on 415 V+/-10% 3 phase , 50 Hz AC power
supply. The unit shall be filled with first charge of the refrigerant and ready for use as
required. The COP at AHRI conditions shall not be less than 3.2and IEER not less than 8
and OEM .
a 522 HP Outdoor Units 522.00 HP 28,263.000 147,53,286.00
4-Way cassette indoor unit
Supply installation,testing and commissioning of following minimum capacity VRF 4-way
Cassette Indoor unit equipped with washable synthetic media pre filetr fan section with
NS low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper
HV-2 coil, electronic expansion valve ,outer cabinet cord less remote control , drain pan
necessary accessories ,remote etc suitable for operation on 230 V +- 10% 50 Hz single
phase AC supply complete as required . The unit shall have automatic force shut down
provision in case of fire on receiving signal from BMS system. The cooling capacity of
Indoor Unit will be at air inlet conditions of 27 Deg C DB and 19 deg C WB temperature.
a 0.8 TR 1.00 Nos 52,300.000 52,300.00
b 1.0 TR 2.00 Nos 52,986.000 1,05,972.00
c 2.0 TR 77.00 Nos 54,356.000 41,85,412.00
d 2.5 TR 13.00 Nos 55,612.000 7,22,956.00
e 3.0 TR 57.00 Nos 56,183.000 32,02,431.00
f 3.5 TR 2.00 Nos 57,953.000 1,15,906.00
Airhandling Units (Ceiling Suspended Type)
Supply, installation, testing and commissioning of DX double skin airhandling units ceiling
suspended type with 24Ga pre coated G.I. outer skin & 24 Ga G.I. inner sking with 40
mm thick PUF insulation of density 42+2 kg/m3 horizontal type AHU complete with DIDW
NS fan, fan motor drive, 4 row deep DX cooling coil, MERV-8 pre filters,mixing box, device,
HV-3 with fire rated canvass connection between CSU and supply air duct, thermal break
profile, vibration isolator pad,Expansion Kit , communication Kit and wired remote
controller as per specifications and drawings.
Cost shall also include supply , installation, testing and commissioning of DOL Starter
cabling upto 10 mtrs , earthing and termination from starter panel till AHU motor.
a 5000CFM ( 14.5 TR) 3.00 Nos. 4,51,063.000 13,53,189.00
Ceiling Suspended Treated Fresh Air Unit
4 3000 CFM 1.00 Nos 3,08,321.000 3,08,321.00
Authorised Signatory Contractor BOQ Page No. 59 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
5 Y Joints
Supply, fixing and commissioning of refrigerant joint / Branch distibutors between
indoors complete with nitrile rubber insulation, supporting etc.,
Supply, fixing and commissioning of refrigerant joint / Branch distibutors between
Outdoors complete with nitrile rubber insulation, supporting etc.,
Refrigerant Piping
Supply installation testing and commissioning including vaccumiazation and Nitrogen
NS testing of following nominal sizes of soft/hard drawn copper refrigerant piping for
HV-6 VRF/VRV system,complete with fittings,with suitable adjustable ring type hanger
6 supports,jointng/brazing including accesories insulated with XLPE Class O tubular
insulation/with Class O closed cell elastemeric nitrile rubber tubular sleeves sections of
specified thickness as below for Suction and Liquid lines, all accessories as per
specification etc as required:
6.1 6.4 mm dia (OD) (soft drawn) with tube thickness 1.2 mm with 19mm thick insulation 65.00 Rm 391.000 25,415.00
6.2 9.5 mm dia (OD) (soft drawn) with tube thickness 1.2 mm with 19mm thick insulation 750.00 Rm 576.000 4,32,000.00
6.3 12.7 mm dia (OD) (soft drawn) with tube thickness 1.2 mm with 19mm thick insulation 450.00 Rm 771.000 3,46,950.00
6.4 15.86 mm dia (OD) (soft drawn) with tube thickness 1.2 mm with 19mm thick insulation 950.00 Rm 962.000 9,13,900.00
6.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19mm thick insulation 625.00 Rm 1,166.000 7,28,750.00
6.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19mm thick insulation 575.00 Rm 1,350.000 7,76,250.00
6.7 25.4 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19mm thick insulation 30.00 Rm 1,537.000 46,110.00
6.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19mm thick insulation 415.00 Rm 1,762.000 7,31,230.00
6.9 31.8 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19mm thick insulation 55.00 Rm 2,558.000 1,40,690.00
6.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19mm thick insulation 150.00 Rm 2,815.000 4,22,250.00
6.11 38.1 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19mm thick insulation 125.00 Rm 3,255.000 4,06,875.00
6.12 41.3 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19mm thick insulation 250.00 Rm 3,511.000 8,77,750.00
Drain Piping
NS Supply, installation testing & commissioning of rigid UPVC piping complete with fittings,
7 HV-7 supports as per specifications and duly insulated with 6 mm thick closed cell nitrile
rubber insulation.
a 25 mm dia ( with 6 mm nitrile rubber Insulation) 690.00 Rm 208.000 1,43,520.00
b 32 mm dia ( with 6 mm nitrile rubber Insulation) 575.00 Rm 251.000 1,44,325.00
c 40 mm dia ( with 6 mm nitrile rubber Insulation) 350.00 Rm 365.000 1,27,750.00
NS Supply & installation of control cum transmission wiring of 2 core x 1.5 sqmm copper in
HV-8 suitable pvc conduits between indoor and out door unit.
NS Supply and laying / fixing on surface/Tray of Power cable of 4Core x 10 sqmm size XLPE
9 HV-9 insulated Copper armoured conductor cable to VRF outdoor unit from main electrical 600.00 Rm 1,656.000 9,93,600.00
panal. The cost shall include all necessary supports clamps etc as necessary as required .
Authorised Signatory Contractor BOQ Page No. 60 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
NS Supplying & Filling of additional refrigerant Gas R410A for charging of ODU & IDU as
HV-10 required
NS SITC of circular/cabinet inline fan complete with motor, BMS compatible starter, cabling
HV-11 between starter and fan etc..
a 1000CFM with 15mm Static 10.00 Nos 36,542.000 3,65,420.00
NS Supply and fixing of following thickness duly laminated aluminium foil finish closed cell
HV-12 Nitrile rubber ( Class O) insulation on existing duct after applying suitable adhesive for
Nitrile rubber . The joints shall be sealed with 50 mm wide and 3mm thick self adhesive
nitrile rubber insulation complete as per specifications and as required.
a 13 mm thick insulation with Al foil 1,100.00 Sqm. 742.000 8,16,200.00
NS Supply and fixing of acoustic lining for supply air duct/ duct plenum with 10 mm open cell
HV-13 nitrile rubber after applying suitable adhesive.
NS Supply ,installation and fixing fire retardant non porous double layer flexible connection
HV-14 between each AHU & TFA
Grilles / Diffuser
NS Supply, installation, testing and commissioning of aluminium powder coated supply and
HV-15 return air grilles/diffusers as per specifications and drawings.
15.1 150 mm wide linear grill 5.00 Sqm 10,848.000 54,240.00
15.2 200 mm wide linear grill 3.00 Sqm 11,990.000 35,970.00
15.3 SA Square Diffuser 8.00 Sqm 14,274.000 1,14,192.00
15.4 RA Square Diffuser 8.00 Sqm 11,990.000 95,920.00
Volume Control Damper
NS Supply & installation of extruded aluminium volume control damper with blades,
16 HV-16 adjustable lever, frame etc for Supply Air and Fresh Air Coonected to AHU as per 12.00 Sqm 8,564.000 1,02,768.00
specifications and drawings.
Cable Tray
Supply and erection of MS cable tray , duly pained as required including erection of the
17 same on wall or ceiling with necessary fixture and other material required to complete the
job in all respect up to the entire satisfaction of Engineer-in Charge of the work
23.23.6.1 MS perforated cable tray painted with powder coating 100 X 50 X2mm 175.00 metre 231.287 40,475.00
23.23.6.2 MS perforated cable tray painted with powder coating 200 X 50 X2mm 415.00 metre 350.949 1,45,644.00
Supply and erection of cable tray cover made of 1.25 mm thick GI sheet as required
HSR-21 including erection of the same on existing cable tray with necessary fixture and other
23.23.7 material required to complete the job in all respect up to the entire satisfaction of
Engineer-in Charge of the work.
23.23.7.1 GI cable tray Cover, suitable for cable tray of 100 X 50 X 2 mm 175.00 Rm 202.711 35,474.00
23.23.7.2 GI cable tray Cover, suitable for cable tray of 200 X 50 X 2 mm 415.00 Rm 340.233 1,41,197.00
PVC CONDUIT
Supply and erection of PVC CONDUIT ISi marked (Medium) recessed in walVceiling etc.
18 including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc.
complete in all respect up to the entire satisfaction of Engineer-in-Charge of work.
23.7.6.2 PVC pipe of 25 mm dia. 2,650.00 Rm 32.148 85,192.00
CABLE TERMINATION
HSR-21 Supply and erection of suitable compression type brass cable glands for underground
24.2.7 Cable :-
24.2.7.2 1O sqmm to 16s qmm Cable 2 to 4 Core 60.00 Nos 44.650 2,679.00
HSR-21 Supply and erection of aluminium lugs heavy duty including crimping etc. up to the entire
24.2.8 satisfaction of the Engineer-in-charge of the work .
Authorised Signatory Contractor BOQ Page No. 61 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
24.2.8.3 10 sqmm 240.00 Nos 6.251 1,500.00
LOOP EARTHING
HSR-21 Providing and fixing 4.00 mm dia G1. Wire on surface or in recess for loop earthing as
24.1.13 required.
ISOLATION BOX WITH MCB/RCCB
HSR-21 Supply and erection of sheet steel enclosures 1 pole/2 pole/4 pole on
23.22.3 walVon existing pedestal complete as required.
23.22.3.2 S.P.N. or DP enclosure suitable for DP MCB/RCCB 30.00 Nos 356.307 10,689.00
Supply and erection double pole/Four pole Residual (RCCB/ELCB) on
HSR-21 240/415V, 5Hz. AC supply installed in existing sheet steel enclosures
23.22.6 including making necessary connections and bonding to earth with all labour and material
required to complete the job in all respect up to the entire satisfaction of the Engineer-in-
Charge of the work.
23.22.6.3 DP RCCB 30ma sensitivity , 63 A 30.00 Nos 2,075.332 62,260.00
POWER PLUG FOR INDOOR UNITS
Providing and fixing GI concealed sheet metal boxes with inner and outer face plate
22 including concealing the box in wall and fixing in position with inner plate and face plate
with all labour and material required for the job complete in all respects.
23.8.10.2 3 Modules 155.00 Nos 126.806 19,655.00
HSR-21 Providing and fixing modular type accessories of approved make in existing box including
23.8.11 fixing and making necessary connections, complete in all respect.
23.8.11.3 15 amp 1 way switch 155.00 Nos 82.156 12,734.00
23.8.11.5 15 amp 6 pin Socket 155.00 Nos 124.127 19,240.00
Ducting
Supply, installation, and commissioning of factory/site fabricated GSS sheet metal
HSR-21 rectangular/round ducting complete with neoprene rubber gaskets, elbows, hangers,
25.7 supports etc. as per approved drawings and specifications of following sheet thickness
complete as required.
25.7.1 Thickness 0.63 mm sheet (0 - 750 mm) 550.00 Sqm 811.737 4,46,455.00
25.7.2 Thickness 0.80 mm sheet (750 - 1200 mm) 310.00 Sqm 971.584 3,01,191.00
25.7.3 Thickness 1.00 mm sheet (1200 - 1500 mm) 150.00 Sqm 1,175.188 1,76,278.00
25.7.4 Thickness 1.25 mm sheet (1500 - 1800 mm) 90.00 Sqm 1,397.545 1,25,779.00
TOTAL TOTAL RS. 378,87,341.00
Authorised Signatory Contractor BOQ Page No. 62 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
( FIRE HYDRANT WORK )
Sr. HSR/ NS
Description of Item Qty Unit Rate Amount
No. Code No.
FIRE HYDRANT WORK - NON SCHEDULED ITEM
Supplying, installation, testing and commissioning of Electric driven Main Fire
Pump suitable for automatic operation and consisting of following, complete in all
respects, as required :
(a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze
impeller with stainless steel shaft, mechanical seal conforming to IS 1520.
1 (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM,
suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for
enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325.
(c) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as
required.
(d) Suitable cement concrete foundation duly plastered with anti vibration pads.
1.1 2280 lpm at 70 m Head 2.00 Set 3,29,574.152 6,59,148.00
Supplying, installation, testing and commissioning of diesel engine driven main
fire pump suitable for automatic operation and consisting of following, complete in all
2 respects, as required: (Diesel Driven Pump)
Horizontal type, multistage, centrifugal pump of cast of iron body and bronze impeller
with stainless steel shaft, mechanical seal conforming to IS 1520.
Suitable HP, 1500 RPM water cooled with radiator, diesel engine conforming to relevant
IS standard complete with auto starting mechanism, 12 /24 volts electric starting
equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly
insulated
with 50 mm thick glass wool with 1.0 mm thick aluminium sheet cladding, residential
silencer, instruments and protection as per standard specification, stop solenoid for auto
stop in the event of
fault with audio indications, painted with post office red colour etc. as required. M.S
fabricated, common base plate, coupling, coupling
guard, foundation bolts etc. as required. Suitable cement concrete foundation duly
2.1 plastered
2280 lpmand withmanti
at 70 Headvibration pads. 2.00 Set 5,46,574.045 10,93,148.00
Supplying, installation, testing and commissioning of electric driven
pressurisation pump suitable for automatic operation and consisting of following,
complete in all respects, as required : (Jockey Pump)
Horizontal type, multistage, centrifugal pump of cast iron body and bronze impeller with
NS stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage
3 induction motor TEFC type -
suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection
for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS :
325. M.S.fabricated Common base plate, coupling, coupling guard, foundation bolts etc.
as required.
Suitable cement concrete foundation duly plastered and with anti vibration pads.
3.1 180 lpm at 70 m Head 2.00 Set 91,435.163 1,82,870.00
Authorised Signatory Contractor BOQ Page No. 63 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Supplying, installation, testing and commissioning of electric driven terrace
pump suitable for automatic operation and consisting of following, complete in all
respects, as required: (Terrace Pump) (a) Horizontal type,
multistage, centrifugal, split casing pump of cast iron body & bronze impeller with
stainless steel shaft, mechanical confirming to IS : 1520
b) Suitable HP squirell cage induction motor TEFC type suitable for operation on 415 volts,
4 3 phase, 50 Hz, AC supply with IP55 class of protection for enclosure, horiziontal foot
mounted type with Class-'F' insulation, conforming to IS-325. Along with starter panel.
(c) M.S.fabricated common base plate, coupling, coupling guard, foundation bolts etc.as
required.
(d) Suitable cement concrete foundation duly plastered and with anti vibration pads.
(MAKE:- PUMP-MATHER & PLATT/KIRLOSKAR/ITT/GRUNDFOS/DP MOTOR-
KIRLOSKAR/ ABB/CROMPTOM or equivalent.)
4.1 900 lpm at 35 m Head 2.00 Set 90,960.087 1,81,920.00
Supplying erection, testing of fully automatic electric control panel board
for Fire Pump Chamber consisting of MS sheet of thickness 14
gauge duly painted box type floor mounted made of angle Frame
containing 1 no. fully automatic air brake starter suitable for Motor of the
following capacity, Min switch of suitable range with HRC fuse, 1 no. volt
NS meter (0 to 500 volts), 1 No. Amp. Meter of O to 100 amp. 3 sets of
FH-5 indicating lamp capacitor of suitable capacity and 1 no. single phase
preventers with the timer switch including wiring in panel board and
suitable electric energy meter wiring in Electric Control Panel Board
complete in all respect as per specification given in Schedule No. II,
Including MCB, suitable, Capacitor, Wooden Box etc as per site
requirement complete in fal respect.
5.1 20 HP Motor 2.00 Each 23,190.317 46,381.00
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe
conforming to IS 1239/3589/IS 1239 including Welding, fittings like elbows, tees, flanges,
NS tapers, nuts bolts, gaskets etc. in ground including welding , exavation and providing
FH-6 cement concreat blocks as supports, anticrossive treatment with coaltar/asphalt tape as
IS 10221 and refilling the trench etc. of following sizes complete as required.
6.1 150mm Dia 50.00 Rmt 3,396.972 1,69,849.00
Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe
conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges,
NS tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable
FH-7 clamp/support frame and painting with two or more coats of synthetic enamel paint of
required shade complete as required.
Make : JINDAL/TATA or equivalent.
7.1 25 mm dia 100.00 Rmt 664.392 66,439.00
7.2 50 mm dia 100.00 Rmt 1,143.933 1,14,393.00
7.3 80 mm dia 100.00 Rmt 1,683.305 1,68,331.00
7.4 100 mm dia 300.00 Rmt 2,281.615 6,84,485.00
7.5 150 mm dia 400.00 Rmt 3,191.582 12,76,633.00
Authorised Signatory Contractor BOQ Page No. 64 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Supplying and fixing single headed internal hydrant valve with instantaneous
NS Gunmetal/Stainless Steel Coupling of 63 mm dia with cast iron wheel ISI marked
8 conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as
required.
8.1 Single headed Gunmetal 18.00 Set 6,827.878 1,22,902.00
Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm
NS dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked,
FH-9 conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as
required :
9.1 Single headed Gunmetal 10.00 Set 6,827.878 68,279.00
Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating
NS with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets
FH-10 conforming to IS 13095 of following sizes as required.
10.1 80 mm dia 28.00 Set 4,448.926 1,24,570.00
10.2 100 mm dia 3.00 Set 5,953.631 17,861.00
10.3 150 mm dia 2.00 Set 8,001.280 16,003.00
Supplying, fixing, testing & commissioning of double flanged sluice valve of
11 rating PN 1.6 with non rising spindle, bronze/gun metal seat, ISI marked complete with
nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :
11.1 80 mm dia 28.00 Set 9,551.528 2,67,443.00
11.2 100 mm dia 3.00 Set 13,074.413 39,223.00
11.3 150 mm dia 2.00 Set 20,326.466 40,653.00
Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade
NS 304) with orifice of required size to be fitted between flange & landing valve of external
FH-12 and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2
complete as required.
Providing, installation, testing and commissioning of non-return valve of following
13 sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts, washers etc.as
required. .
13.1 80 mm dia 2.00 Set 6,868.063 13,736.00
13.2 100 mm dia 3.00 Set 9,867.650 29,603.00
13.3 150 mm dia 1.00 Set 15,882.898 15,883.00
Providing, installation, testing and commissioning of stainless steel Y-Strainer
14 fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with
stainless steel flange.
14.1 150 mm dia 2.00 Set 9,951.592 19,903.00
Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and
15 female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as
required.
15.1 Gun Metal 28.00 Set 4,645.386 1,30,071.00
Supplying and fixing first-aid Hose Reel with MS construction spray painted in post
office red, conforming to IS 884 complete with the following as required. 20 mm nominal
NS internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20
FH-16 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the
equipmets on wall.
Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket.
Authorised Signatory Contractor BOQ Page No. 65 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal
NS internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection
FH-17 to interconnect hose pipe coupling as required.
17.1 Gun metal 28.00 Each 2,157.488 60,410.00
NS Supplying and fixing of fire brigade connection of cast iron body with gun metal
18 male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia
MS pipe connection conforming to IS 904 as required.
18.1 2way-100 mm dia M.S. Pipe 2.00 Set 6,020.606 12,041.00
Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm
NS in height with air release valve on top and flanged connection to riser, drain arrangement
FH-19 with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and
paintingwith synthetic enamel paint of approved shade as required.
NS Providing & fixing of pressure switch in M.S. pipe line including connection etc. as
FH-20 required.
NS Providing & fixing flow switch in following sizes M.S. pipe including connection etc as
FH-21 required.
21.1 100mm dia 3.00 Each 6,710.002 20,130.00
21.2 150mm dia 2.00 Each 8,055.753 16,112.00
Providing, fixing, testing & commissioning of installation control valve of cast
iron body, brass/bronze working parts comprising of water motor alarm, bronze seat
NS clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous
22 alarm when the wet riser/sprinkler system activates, pressure gauges, emergency
releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test
control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of
follwing sizes as required.
22.1 150mm dia 2.00 Set 42,772.914 85,546.00
NS Providing and fixing S.S Pressure Gauge complete as required complete in all
FH-23 respect.
23.1 Dial diameter 100mm calibration 0-16 Kg 4.00 Each 686.279 2,745.00
Supplying, Installation, Testing and Commissioning of weather proof cabinet for
hose fabricated out of 1.6mm thickness M.S. sheet with front glass door having locking
24 arrangement, suitable to accommodate all the necessary pipes, accessories, fittings etc
including painting the metal portion with one coat of ready mixed primer paint and two
coats of synthetic enamel paint of approved shade and quality, sign writing etc.
24.1 900 mm wide x 600 mm high x 500 mm deep Size (for Hydrant Points ) 10.00 Each 4,697.359 46,974.00
24.2 600 mm wide x 600 mm high x 300 mm deep Size - (for RRL Reel) 18.00 Each 3,665.490 65,979.00
NS Supplying, Installation, Testing and Commissioning standard Fire Man's axe with
FH-25 heavy insulated rubber conforming to IS 936 complete in all respect.
NS Supply and fixing of 6kg ABC type fire extinguisher as per IS:15683(6 kg.) including
26 cost of petty material required to complete the work upto the entire satisfaction of
Engineer In Charge.
26.1 6 Kg. Capacity 80.00 Each 2,492.345 1,99,388.00
Supply and fixing of 4.5kg C02 gas type fire extinguisher as per IS: 15683(4.5 kg.)
27 with including cost of petty material required to complete the work upto the entire
satisfaction of Engineer In Charge.
27.1 4.5 Kg. Capacity 80.00 Each 6,060.862 4,84,869.00
Supply. Installation, Testing and Commissioning of Ball Valve 25 mm dia witth
28 including cost of petty material required to complete the work upto the entire satisfaction 28.00 Each 414.352 11,602.00
of Engineer In Charge.
Authorised Signatory Contractor BOQ Page No. 66 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
NS Supply. Installation. Testing & Commissioning of Fire Bucket Stand with four No:
FH-29 buckets.
NS Supply. Installation. Testing & Commissioning of 5Kg Automatic Modular Fire
FH-30 Extinguisher.
NS Supply. Installation. Testing & Commissioning of 15Kg Automatic Modular Fire
FH-31 Extinguisher.
TOTAL RS. 70,79,519.00
Authorised Signatory Contractor BOQ Page No. 67 Digitally signed by SUNIL NBCC
KUMAR JHA
Date: 2023.11.09 15:37:42 IST
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.06 MB
CS_cover_1_TechSheet_CRSU.xlsx
Tender Document
Integrity Pact.pdf
Tender Document
GCC Contracting PMC 2022 upto six Ammdment.pdf
Tender Document
CS_cover_2_Quote_Sheet.xlsx
Tender Document
Annexure IA Physical Milestones.pdf
Tender Document
SOIL REPORT.pdf
Tender Document
TechnicalSpecs.pdf
Tender Document
tenderdrawings.pdf
Tender Document
Approvedmakes.pdf
Tender Document
SCC.pdf
Tender Document
NIT CRSU Jind.pdf
Tender Document
Additional Drwg Annexure B.pdf
Tender Document
Additional Drwg Annexure C.pdf
Tender Document
BOQTBIII.pdf
Tender Document
corrigendum-2191-Corrigendum_02_CRSU.pdf
pdf • 0.08 MB
addendum-e6a71cfbf94b-Cor_Adm_01_JInd.pdf
pdf • 0.19 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .