PROVN OF PARKING SHED AT UNIT 524, 02 x BATHROOM CUM TOILET IN (MRSAM), SPL RPR /REPLACEMENT OF CELING FAN, EXHAUST FAN, WALL FAN, CABIN FAN AND GYSERS AT 4CSR, BELONIA,CHANDPUR,155 BH AND SPL RPR TO BER PUMPS, LT PANEL AT MISA CAMP UNDER GE (S) TEZ

Amount

S&F Submersible pump set, electric driven 415 V, 50 HZ, 3 PH suitable for 200/250 mm dia bore well (Casing pipe size 200/250 mm) of capacity 22.5 HP, Head range 21- 68 meter, rated speed 2850 RPM, discharge range 1000-1875 LPM suitable for pipe of size 100 mm all as specified and directed. Make KSB/Kirloskar/Crompton Notes :- (i) Necessary foundation, base frame & bolting required for installation high pump set shall be provided as per manufacturer's recommendation and shall be measured and the cost for the same shall be deemed to be included in the rates quoted for this item. (ii) The cost of PVC insulated industrial heavy duty cable and all other standard accessories shall be deemed to be included in the rates quoted for this item.

Supply, install, fixing, commissioning and testing of mono block pump set of capacity 5.0 HP, suction and deliver size 80x80 mm, Head range 6-21 meter, discharge 700-1500 LPM conforming to IS :12615, 415 Volt, 3 phase, 1450 rpm-50 Hz, AC supply and suitable for drinking water including suitable size factory mild steel base frame fixed in and including foundation as per manufacturer's recommendation with nuts and bolts including anti vibration pads, painting and connection with suction & discharge water main complete with standard fittings and necessary electric connections with PVC insulated heavy duty copper cable 10 Sqmm, 1100 volt from starter to pump set complete all as specified and as directed. Notes :- (i) Necessary foundation, base frame & bolting required for installation high pump set shall be provided as per manufacturer's recommendation and shall be measured and the cost for the same shall be deemed to be included in the rates quoted for this item. Make KSB/Kirloskar/Crompton (ii) The cost of PVC insulated industrial heavy duty cable and all other standard accessories shall be deemed to be included in the rates quoted for this item.

S&F Non clogging pump set of capacity 5.0 HP, 415 V, 50 HZ, 3 Phase, Head range 9-18.5 metre, discharge 1200 LPM all as specified and directed. Notes :- (i) Necessary foundation, base frame & bolting required for installation high pump set shall be provided as per manufacturer's recommendation and shall be measured and the cost for the same shall be deemed to be included in the rates quoted for this item. (ii) The cost of PVC insulated industrial heavy duty cable and all other standard accessories shall be deemed to be included in the rates quoted for this item.

S&F Non clogging Diesel engine pump set of capacity 5.0 HP, 415 V, 50 HZ, 3 Phase, Head range 9-18.5 metre, discharge 1200 LPM all as specified and directed. Notes :- (i) Necessary foundation, base frame & bolting required for installation high pump set shall be provided as per manufacturer's recommendation and shall be measured and the cost for the same shall be deemed to be included in the rates quoted for this item. Make KSB/Kirloskar/Crompton (ii) The cost of PVC insulated industrial heavy duty cable and all other standard accessories shall be deemed to be included in the rates quoted for this item.

Excavation in trenches not exc 1.5 m in depth and not exc 1.5 m wide for taking out/laying XLPE cable/CI/GI pipes and getting out in soft/loose soil complete all specified/directed

Removing excavation soil at a distance not exc 50 m and deposited where directed complete all as directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exc 25 cm complete all as directed.

M&L for sand cushioning with clean dry sand for protection of under ground cable complete all as specified and as directed. Note :- Punned thickness of sand layer shall be measured and paid to contractor.

M&L for Brick Sub Class 'B' locally available best quality laid in trenches with width equal to length of the bricks, above sand cushioning for cable protection complete all as specified and as directed.

S&F in replacement steel water tubing 50 mm dia of bore light grade galvanised with all fittings laid in trenches / fixing with surface of wall after drawn through electric cable by means of nuts bolt and washers all as directed .

S&F in replacement steel water tubing 80 mm dia of bore light grade galvanised with all fittings laid in trenches / fixing with surface of wall after drawn through electric cable by means of nuts bolt and washers all as directed .

Supply, laying in repair in trenches of XLPE UG cable insulated aluminium stranded conductor served with an inner sheathing or PVC tape heavy duty armoured upto 1100volts (earthed) GI steeel strip and overall PVC sheathed nominal cross sectional area 10 sqmm 2 core and testing complete all as specified and directed.

Supply, laying in repair in trenches of XLPE UG cable insulated aluminium stranded conductor served with an inner sheathing or PVC tape heavy duty armoured upto 1100volts (earthed) GI steeel strip and overall PVC sheathed nominal cross sectional area 35 sqmm 4 core and testing complete all as specified and directed.

Supply, laying in repair in trenches of XLPE UG cable insulated aluminium stranded conductor served with an inner sheathing or PVC tape heavy duty armoured upto 1100volts (earthed) GI steeel strip and overall PVC sheathed nominal cross sectional area 50 sqmm 4 core and testing complete all as specified and directed.

Supply, laying in repair in trenches of XLPE UG cable insulated aluminium stranded conductor served with an inner sheathing or PVC tape heavy duty armoured upto 1100volts (earthed) GI steeel strip and overall PVC sheathed nominal cross sectional area 70 sqmm 4 core and testing complete all as specified and directed.

Supply and fix in replacement of aluminium lug of size 6/16 Sqmm for connecting Aluminium XLPE cable all as specified and directed.

Supply and fix in replacement of aluminium lug of size 35/70 Sqmm for connecting Aluminium XLPE cable all as specified and directed.

M&L for Boring holes horizontally under Road without damaging the surface of Road (minimum 1.0 METRE below the Road Surface/footpath with the help of GI Tubing not exc. 80mm bore (dia) for passing of UG Cable, complete all as specified and directed NOTE: GI Pipe laid will be measured and paid separately under appropriate Item.

Supply, installation, testing and commissioning of factory made powder coated outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including aluminium bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . INCOMING:- (i) MCCB TPN 200 amps, 4 pole, breaking capacity 16 KA suitable for operation of 415 volts AC 50 HZ with adjustable type and all as specified in SSR Part -I and earth leakage module - 01 No, (ii) LED Type indicator lamp R-Y-B (1 Set), (iii) 4 strip aluminium coated copper bus bar of rating 1.5 times current carrying capacity of incoming switch gear. (B) OUTGOING (i) MCCB TPN 100 A, 4 Pole, 415 Volts, 16 KA, C Curve - 02 No (ii) MCB TPN 63 A, 4 Pole, 240 Volts, 10 KA, C Curve - 02 Nos

Supply, installation, testing and commissioning of factory made powder coated outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including aluminium bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . INCOMING:- (i) MCCB TPN 200 amps, 4 pole, breaking capacity 16 KA suitable for operation of 415 volts AC 50 HZ with adjustable type and all as specified in SSR Part -I and earth leakage module - 01 No, (ii) LED Type indicator lamp R-Y-B (1 Set), (iii) 4 strip aluminium coated copper bus bar of rating 1.5 times current carrying capacity of incoming switch gear. (B) OUTGOING (i) MCB TPN 63 A, 4 Pole, 240 Volts, 10 KA, C Curve - 04 Nos (ii) MCB SPN 32-63A, 2 Pole, 240 Volts, 10 KA, C Curve - 16 Nos

Supply, installation, testing and commissioning of factory made powder coated outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including aluminium bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . INCOMING:- (i) MCCB TPN 100 amps, 4 pole, breaking capacity 16 KA suitable for operation of 415 volts AC 50 HZ with adjustable type and all as specified in SSR Part -I and earth leakage module - 01 No, (ii) LED Type indicator lamp R-Y-B (1 Set), (iii) 4 strip aluminium coated copper bus bar of rating 1.5 times current carrying capacity of incoming switch gear. (B) OUTGOING (i) MCB TPN 63 A, 4 Pole, 240 Volts, 10 KA, C Curve - 02 Nos (iii) MCB SPN 32-63A, 2 Pole, 240 Volts, 10 KA, C Curve - 14 Nos

Supply, installation, testing and commissioning of factory made powder coated (approved make) outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including aluminium bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . INCOMING:- (i) MCCB TPN 200 amps, 4 pole, breaking capacity 16 KA suitable for operation of 415 volts AC 50 HZ with adjustable type and all as specified in SSR Part -I and earth leakage module - 01 No, (ii) LED Type indicator lamp R-Y-B (1 Set), (iii) 4 strip aluminium coated copper bus bar of rating 1.5 times current carrying capacity of incoming switch gear. (B) OUTGOING (i) MCB TPN 63 A, 4 Pole, 240 Volts, 10 KA, C Curve - 04 Nos (ii) MCB SPN 32-63A, 2 Pole, 240 Volts, 10 KA, C Curve - 16 Nos

Supply, installation, testing and commissioning of factory made powder coated outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including aluminium bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . INCOMING:- (i) MCCB TPN 200 amps, 4 pole, breaking capacity 16 KA suitable for operation of 415 volts AC 50 HZ with adjustable type and all as specified in SSR Part -I and earth leakage module - 01 No, (ii) LED Type indicator lamp R-Y-B (1 Set), (iii) 4 strip aluminium coated copper bus bar of rating 1.5 times current carrying capacity of incoming switch gear. (B) OUTGOING (i) MCB TPN 63 A, 4 Pole, 240 Volts, 10 KA, C Curve - 14 Nos (ii) MCB SPN 32-63A, 2 Pole, 240 Volts, 10 KA, C Curve - 08 Nos

Supply, installation, testing and commissioning of factory made powder coated outdoor type, dust & vermin proof feeder pillar box made out of 3.15mm CRCA steel sheet of suitable size and angle iron 40 mm x 40mm x 6 mm , powder coated over one coat of red oxide primer suitably grouted in PCC-M10 using 20 mm graded stone aggregate including aluminium bus bar, internal wiring with PVC insulated single core cables of copper conductor of suitable size duly numbered with tags for the circuits with hinged double door shutters (front & rear), cubical type locking arrangement and slanted roof. The size of panel boards shall be suitable for housing the accessories given here under and also suitable for operation on AC 415 Volt, 3 phase, 50 Hz supply system. The panel board shall comprise of following items & all specified in SSR Part-I clause no 19.21 and all as shown on drawing . INCOMING:- (i) MCCB TPN 125 amps, 4 pole, breaking capacity 16 KA suitable for operation of 415 volts AC 50 HZ with adjustable type and all as specified in SSR Part -I and earth leakage module - 01 No, (ii) LED Type indicator lamp R-Y-B (1 Set), (iii) 4 strip aluminium coated copper bus bar of rating 1.5 times current carrying capacity of incoming switch gear. (B) OUTGOING (i) MCCB TPN 63 A, 4 Pole, 240 Volts, 16 KA, C Curve - 02 Nos (ii) MCCB TPN 32 A, 4 Pole, 240 Volts, 16 KA, C Curve - 01 Nos (iii) MCB SPN 6-32 Amp-04 Nos

Material & Labour for earthing with galvanised steel earth plate electrode of size 60cmx60cmx6mm thick buried directly in ground (earth pit not less than 2.25m deep below the ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to the galvanised earth lead by means of bolts, nuts check nuts and washers of galvanised iron or steel using GI strip 32x6mm as earthing lead as shown in electrical plate No. 3 of SSR Part-I connected to earthing test point all as specified or indicated including testing on completion including necessary excavation and earth work in soft/loose soil, returning filling, disposal of surplus soil, earth pit in PCC 1:3:6 type C-1 using 20mm graded stone aggregate pit, funnel, 20mm dia GI light grade watering pipe, 40mm dia GI light grade earth lead protection pipe, CI frame and cover, wire, copper lugs etc mesh, charcoal and common salt in alternate layer complete all as specified and directed by Engr-in-Charge.

S&F in replacement of PVC insulated three core sheathed submersible flat cable of size 16 Sqmm for submersible pumps with copper conductor 1100 Volts grade conforming to IS:694/1990 ISI all as specified and directed.

S& F Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) fixing of fan to the existing hook all as specified and directed. Make-Crompton cat No CFENESV480PW5S( without remote control) or ORIENT cat No HECTOR 500 (w/o remote control) or Equivalent in Bajaj /HAVELLS/KAITAN/USHA

Supply and fixing Wall mounting fan 450 mm sweep. Make:ORIENT cat No TORNADO Black metal or Equivalent in Bajaj /HAVELLS/KAITAN/USHA/CG

Supply and fixing Cabin fan 400 mm sweep. Make:HAVELLS cat No swing-GYRO -3 blade or Equivalent in Bajaj /ORIENT/KAITAN/USHA/CG

Supply and fixing Pedestal fan 400 mm sweep Heavy duty. Make: Make:HAVELLS cat No ULTRA HIGH SPEED or Equivalent in Bajaj /ORIENT/KAITAN/USHA/CG

Supply & fix Heavy Duty Exhaust Fans of sweep 450 mm with louvers of Make:: Havells cat No TURBO FORSE or equivalent in Bajaj/Crompton/Usha/Almonard/Khaitan/CG

Supply & fix Heavy Duty Exhaust Fans of sweep 225 mm with louvers Make:: USHA cat No TURBO or equivalent in Bajaj/Crompton/Usha/Almonard/Khaitan/CG/Havells

Material and labour for cutting wall and making hole suitable for fixing Exhaust fan 150/300 mm sweep and making good disturbed surface all as per existing all as directed at site

Supply and fix electric vertical water heater, storage type, heating element upto 2 KW capacity 50 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, Stainless steel connection pipes (Hot and cold) etc. Make : Havells Cat No MONZA or Equivalent in Bajaj/Crompton/Usha/CG

Supply and fix electric vertical water heater, storage type, heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostat, NRV, Stainless steel connection pipes (Hot and cold) etc. Make : Havells Cat No PURO-TURBO or Equivalent in Bajaj/Crompton/Usha/CG

M&L PCC 1:4:8 type D-2 (using 40 mm graded stone agg) as in foundation ,filling mass complete all as specified & directed.

M&L cement concrete in foundation type B 2, 1:2:4 ( 40 mm graded stone aggregate) as in filling and mass concrete all as specified & directed.

S&F posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, wind ties, etc.; flat iron fillets ( for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work such as vertical MS steel tubular pole for supporting trusses etc. conforming to Fe 290 Gde E-165 complete all as directed.

S&F steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes confirming to IS 1161-1979 grade St-240 medium weight all as specified & directed.

S&F mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other , or screwed both ends , each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5 cm long and dia of shank 11 to 15 mm all as specified & directed.

S&F mild steel bolts purpose made with hexagonal or square heads at one end and screwed the other , or screwed both ends , each screwed end to be fitted with washers and one hexagonal or square nut, exc 30mm long and dia of shark 12 to 20 mm all as specified & directed.

S&F pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 mpa as in roof covering/cladding to wall, fixed with self tapping screws all as specified & directed.

S&F Hand rails, half round or other steel section or core for wooden hand rail straight portion ,drilled and counter sunk for blusters nosing to steeps including embedding in concrete and screwing et ,wind ties for roofs including securing bolts posts and struts in fencing including cutting tops to shape as directed ,drilling holes ,notching for wire etc posts and struts in fencing including cutting tops to shape as directed, drilling holes, notch ng for wire, wind ties, etc.; flat iron fillets ( for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 290 Gde E-165 complete all as directed.

S&F mild steel rolled section conforming to Fe-290 (Gde E-165), as in main and cross beams, hip and jack rafters, purlins where connected to common rafters fixed with angle cleats and other connecting plates etc. complete all as specified and directed.

M&L applying two coats of synthetic enamel paint over a coat of red oxide or zinc chromate primer including preparation of new steel or iron surfaces exc 10 cm width or girth, complete all as specified and directed.

M&L brick work with sub class' B' bricks of old size, straight or curved on plan exc 6 m mean radius built in cement mortar 1:6 all as specified & directed.

M & L rendering 15mm thick on brick wall or concrete surface consisting two layers, under layer of 10mm thick in CM (1:6) & top layer of 5mm thick in cement mortar 1:4 mixed with water proofing compound, finished even and smooth without using extra cement complete all as specified and directed. (Note:- Water proofing compound shall be measured and paid separately.)

M & L applying for two coats of colour wash over a coat of white wash on newly plastered or unplastered wall surfaces including preparation of surfaces, complete all as specified & directed.

Surface dressing not exc 15 cm deep in soft/loose soil all as specified & directed.

Spreading,levelling,watering and well ramming the earth filling under floor not exc. 25cm thick in layers all as specified & directed.

M & L hardcore of broken stone or boulders of gauge n.exc.63mm,deposited,spread and levelled in layers n exc. 15 cm thick, watered and well rammed to a true surface, complete all as specified and directed.

M & L cement concrete tye D-2, 1:4:8 ( 40 mm graded aggregate ) 75 mm thick as in sub base of floors all as specified & directed.

M&L 25mm th PCC 1:2:4 type B-0 using 12.5mm graded aggregate as in flooring, finished fair and even all as specified & directed.

M&L non-skid coloured ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 15 mm thick screed bed or bedding layer in CM (1:4) complete all as specified and directed.

M & L rendering 10mm thick on brick wall or concrete surface in cement mortar 1:4 finished fair and even complete all as specified & directed.

M&L glazed ceramic tiles in vertical surfaces 300x200x7 mm thick, set & jointed in neat cement slurry and pointed in coloured cement to match coloured tiles laid over and including 10 mm thick rendering in CM (1:4) complete all as specified and directed.

M & L rendering 15mm thick on brick wall or concrete surface in cement mortar 1:6 finished fair and even complete all as specified.

S&F steel windows with side hung shutters including projecting type hinges with steel handles, steel peg stays complete with glazing bars dovetailed or welded, complete all as specified and directed.

S&F steel ventilators with top hung shutters including hinges, steel peg stay, complete all as specified and directed.

M & L sheet glass ordinary quality 3mm thick and glazing with oil putty in squares n.exc. 0 .5 sqm each pane complete all as specified & directed.

S&F solid PVC door frame of size 50mm X 47mm made out of 5mm plain colour PVC sheet reinforced with MS square tubes, as per specifications and drawing complete or as directed by Engineer-In-Charge.

S&F factory made solid PVC door shutter 30mm thick(style) consisting of frame made out of MS tubes for bottom and top rails. MS frame shall be covered heat moulded plain colour PVC 'C' channel having PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail& bottom rail on either side & as gap insert for top rail & bottom rail; Panelling for plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading, and jointed together with solvent cement, supplying and fixing in the frame at the site as per specification all as specified & directed.

Providing precast reinforced cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, all as specified and directed.

M & L 75mm th PCC 1:3:6 type C-1 using 20mm graded stone aggregate as in plinth protection finished even and smooth without using extra cement complete all as specified & directed.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required, including binding with mild steel wire (annealed) not less than 0.9mm dia all as specified & directed.

S&F TMT bars 5mm and over upto and including 10mm dia in stirrups, spacers and binders bent to shape required, including binding with mild steel wire (annealed) not less than .9mm dia all as specified & directed.

S&F 100 mm size MS butt hinges medium weight cold rolled fixed/ welded to frame complete all as directed.

S&F 75 mm size MS butt hinges medium weight cold rolled fixed/ welded to frame complete all as directed.

S&F125 mm long,aluminium,anodised, barrel tower bolts of extruded section all as directed.

S&F 125mm size aluminium handles, cast type, anodised all as directed.

Cutting chases, pinning in , for concealed water tubing on brick walls, making good to facing where required and pointing in cement mortar 1:3, not exc 10 cm girth all as specified & directed.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 15 mm bore GI tubing all as specified & directed.

S&F medium grade galvanised steel tubing with all fittings fixed to wall or laid in floors for 20 mm bore GI tubing all as specified & directed.

S&F 15 mm dia bib tap cast copper alloy (fancy type), chromium plated, with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule all as specified & directed.

S&F stop valve, cast copper alloy, fancy type, chromium plated with long shank and cup (Concealed type), screwed down both ends for high pressure, as per ISI suitable for 15mm dia iron pipe all as specified & directed.

S&F15 mm dia brass chromium plated pillar tap, fancy type with or without lettered 'Hot' or 'Cold' ,with long screwed shanks and fly nut, capstan head, screwed for 15mm dia pipe all as specified & directed.

S & F PVC connection 15x450mm size all as specified & directed.

S&F vitreous china water closet Pedestal pattern( white ) excluding fixing bolts, flushing cistern and flush pipe complete all as specified & directed.

S&F rotational moulded polythene water storage tank 3 layer (Cylindrical vertical with closed top)hoisted and fixed in position of 1000 ltrs capacity fixed with PVC tank nipples, complete all as specified in SSR Part I Incl.dismentling of existing tank and removing to store all as specified & directed.

Supply only 10 ltrs capacity (PVC), valve less, symphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets, complete all as specified and directed. Note:- The rate for fixing flushing cistern are deemed to be included with the rate of fixing water closet any type all as specified & directed.

Supply only 32mm dia flush pipe of polyethylene of low or high density, for low or high level flushing cistern. Note:- The rate for fixing flush pipe are deemed to be included with the rate of fixing water closet any type.all as specified & directed.

S&F 15mm bore Chromium Plated angle valve of approved make, screwed down for iron on both ends pipe all as specified & directed.

S&F vitreous china, white, wash hand basin, flat back size 550x400mm 'including MS brackets including cutting for and pinning in, but excluding waste pipe

Supply only 32mm dia waste pipe of polythelene,flexible, for wash hand basin or kitchen sink all as specified & directed.

S&F 20mm dia brass chromium plated tubular towel rails,D type,60cm long between flanges, complete all as specified & directed.

S&F 160mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 110mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors, complete all as specified and directed.

S&F 110mm PVC (SWR), Junction single, (Single T) equal or unequal), fixed with solvent cement, with oval access door, complete all as specified and directed.

S&F 110mm PVC(SWR) bends any radius complete all as specified and directed.

S&F 75mm PVC(SWR) bends any radius complete all as specified and directed.

S&F 75mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete all as specified and directed.

S&F 75mm PVC(SWR) vent cowl complete all as specified and directed.

M&L 75mm dia PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 110mm bore PVC (SWR) 'P' trap, including fixed with solvent cement complete all as specified and directed.

M & L in repairs cast iron floor trap with grating 75mm dia including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

M&L salt Glazed stone ware drain pipe 150 mm bore grade 'A' laid in trenches and jointed and testing complete all as specified & directed.

M&L PCC 1:4:8 type D-2 (using 40 mm graded stone aggregate) as in concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid and tested for 150 mm dia SWG pipe complete all as specified & directed.

Cutting in to existing manholes for connecting new drains, making good to pipe & rendering cutting out existing benching for and forming branch channel in cement concrete1:2:4 type B-1 smooth finished and reforming benching as required for 110 mm bore drain pipe all as specified & directed.

M&L for RCC (1:2:4) type B1 ( using 20mm graded stone aggregate) as in slabs supported on walls and the like all as specified & directed.

Form work to soffits of suspended slabs flat surface of concrete finished rough surfaces of concrete not exceeding 200mm thick, complete all as specified and directed.

M&L applying two coats of synthetic enamel paint over a coat of pink primer to new wooden surfaces exc 10 cm width or girth, including preparation of surfaces, complete all as specified and directed.

D G Corporation

M/S Deep-Jeet

shyam constructions

Anil Kumar Sarmah