Interior works in fourth floor common area at Sahya building, Cyberpark Kozhikode.

Amount

CIVIL WORKS

50.6.1.2 : Solid block masonry using pre cast solid blocks (Factory made) of size 40x20x20cm or nearest available size confirming to IS 2185 part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement: 6 coarse sand) etc complete.

12.45.1 : Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/ sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37 mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5x25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with:12.5 mm thick tapered edge gypsum plain board conforming to IS : 2095-Part 1

26.26.1 : Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge.With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles.

13.80 : Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

13.85.3 : Applying priming coats with primer of approved brand and manufacture, having low VOC ( Volatile Organic Compound) content.With water thinnable cement primer on walls surface having VOC content less than 50 grams / litre

13.60.1 : Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade:Two or more coats on new work

13.62.1 : Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture .

9.105.3 : Providing and fixing partition upto ceiling height consisting of G.I. frame and required board, including providing and fixing of frame work made of special section power pressed/ roll form G.I. sheet with Zinc coating of 120 gms/ (both side inclusive), consisting of floor and ceiling channel 50 mm wide having equal flanges of 32 mm and 0.50 mm thick, fixed to the floor and ceiling at the spacing of 610 mm centre to centre with dash fastener of 12.5 mm dia meter 50 mm length or suitable anchor fastener or metal screws with nylon plugs and the studs 48 mm wide having one flange of 34 mm and other flange 36 mm and 0.50 mm thick fixed vertically within flanges of floor and ceiling channel and placed at a spacing of 610 mm centre to centre by 6 mm dia bolts and nuts, including fixing of studs along both ends of partition fixed flush to wall with suitable anchor fastener or metal screws with nylon plugs at spacing of 450 mm centre to centre, and fixing of boards to both side of frame work by 25 mm long dry wall screws on studs, floor and ceiling channels at the spacing of 300 mm centre to centre. The boards are to be fixed to the frame work with joints staggered to avoid through cracks, M.S. fixing channel of 99 mm width (0.9 mm thick having two flanges of 9.5 mm each) to be provided at the horizontal joints of two boards, fixed to the studs using metal to metal flat head screws, including jointing and finishing to a flush finish with recommended jointing compound, jointing tape, angle beads at corners (25 mm x 25 mm x0.5 mm), joint finisher and two coats of primer suitable for board as per manufacture's specification and direction of engineer in charge all complete.66 mm overall thickness Partition with 8 mm thick double skin Calcium Silicate Board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process with Compressive Strength 225 kg/sq cm, Bending Strength 100 kg/sq cm

HVAC WORKS

16.12.1.1 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006 24 Guage

16.12.1.2 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular ducting as per IS 655-2006 22 Guage

16.12.1.3 : Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.Factory fabricated GSS sheet metal rectangular dueling as per IS 655-2006 20 Guage

16.13 : Supply, Insulation, testing and commissioning of GI volume control duct damper complete with neoprene rubber gaskets, nuts, bolts, screws linkages, flanges etc, as per specifications. GI volume control duct damper

16.17 : Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminum with aluminum volume control dampers with anti smudge ring and removable core.

16.18 : Supplying, fixing testing commissioning of Return air diffusers of powder coated aluminum without volume control dampers with anti smudge ring and removable core.

od71674/2021_2022 : Providing and fixing of 150mm Spigot damper

od71723/2021_2022 : Providing and fixing of 200mm Spigot damper

od71748/2021_2022 : 300X300 PLENUM BOX : Supply and installation of GI factory-fabricated plenum boxes with acoustic insulation out of 18mm thick open cell noise absorbing material with necessary angle frame, support etc.

od71749/2021_2022 : 375X375 PLENUM BOX : Supply and installation of GI factory-fabricated plenum boxes with acoustic insulation out of 18mm thick open cell noise absorbing material with necessary angle frame, support etc.

16.19.1 : Supplying, installation, testing & commissioning of thermal insulated flexible duct of following sizes duly supported at regulator interval as per site requirement etc. complete as required as per specifications.Thermal insulated flexible duct (200 mm dia)

16.21 : Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m3, with 25 mm X 25 mm Gl section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications. 16 <br> <br>Acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m3

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class “O”) insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.Density of material shall be 40-60 kg/cubm 13 mm thick

FIRE PROTECTION SYSTEM

od72041/2021_2022 : Supply, erection, testing & commissioning of (Pendant Type) sprinkler heads with all supports, fixings and fittings all as specified and as shown on drawings and complying to authority regulations and relevant standards

od72042/2021_2022 : Supply, erection, testing & commissioning of Up-Right type sprinkler heads with all supports, fixings and fittings all as specified and as shown on drawings and complying to authority regulations and relevant standards

od72043/2021_2022 : Supply, Installation, Testing and Commissioning of 1000mm Length Sprinkler Flexible type of approved make.

od72044/2021_2022 : MULTI SENSORS: Supply, Installation, Testing and Commissioning of Intelligent Addresable Multi Sensor with optical smoke element and thermal element. The detector shall have facility to mount in different comprehensive environment like Hostile environment, Parking Garage, HVAC Ducts, Precious storage, Transformer rooms, Warehouse, Dormitory and normal working environments.

od72045/2021_2022 : FIRE SURVIVAL CABLE : Supply, Installation, Testing and Commissioning of Fire Survival Cables conforming to BS: 7846 armoured 2 core x 1.5 sqmm.

od72046/2021_2022 : Supplying and making Endtermination with single compression gland of Size 12mm for PAS and FAS wiring connections

ELECTRICAL WORKS

1.14.1 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2x1.5 sq.mm + 1x1.5 sq.mm earth wire

1.14.2 : Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface / recessed medium class PVC conduit as required2X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

1.17.3 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 X 1.5 sq.mm

1.17.12 : Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface / recessed steel/ PVC conduit as required.3 x 2.5 sq. mm

1.21.1 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.20 mm

1.21.2 : Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/ recess including cutting the wall and making good the same in case of recessed conduit as required.25 mm

1.24.1 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 amps switch

1.24.4 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.3 pin 5/6 amp socket outlet

1.24.3 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.15/16 amp switch

1.24.5 : Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.6 pin 15/16 amp socket outlet

1.26 : Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

1.27.1 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.1 or 2 Module (75mmX75mm)

1.27.2 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.3 Module (100mmX75mm)

1.27.4 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.6 Module (200mmX75mm)

1.27.5 : Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.8 Module (125mmX125mm)

od71784/2021_2022 : Supply, installation, testing and commissioning of pre-wired light fittings of all types complete with all mounting accessories, etc. directly on walls or on surface / recessed / suspended from ceilings and giving connection with required length of 1.5sq.mm., 3 core PVC insulated and PVC sheathed copper conductor flexible wire conforming to ISS, etc. as required. Low glare, hight effeciency recessed mounted LED down light - square profile. Lumen output: 850lm, Light colour: Neutral White - 5000K, Power consumption: 15W, Driver: Non-integral constant current electronic driver with a gear tray, Optics: High efficiency optics with high reflective diffuser providing efficient glare free lighting

od101795/2021_2022 : Supply, installation, testing and commissioning of following MV Panels made of 14 SWG thick CRCA sheet fully compartmentalised with 16 SWG CRCA sheets, duly rust inhibited, degreased, zinc phosphated and powder coating painted with approved colour and quality, complete with hinged and earthed front doors, name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made of 3mm thick sheet steel boards with following accessories. , Incomer, 400A, 35 kA, 4P MCCB - 1No, Indication Lamp Set, Bus bar: 400A, 4P, Al (Electrical Grade), 35kA, Outgoing, 250A, 35kA, 4P MCCB - 4Nos

od71785/2021_2022 : Supply, installation, testing and commissioning of following MV Panels made of 14 SWG thick CRCA sheet fully compartmentalised with 16 SWG CRCA sheets, duly rust inhibited, degreased, zinc phosphated and powder coating painted with approved colour and quality, complete with hinged and earthed front doors, name plate, danger notice board, heavy duty rubber gaskets, removable gland plates made of 3mm thick sheet steel boards with following accessories. MP-TYP, Incomer, 250A, 4P, Isolator - 1No, Indication Lamp Set - 1No, Bus bar: 250A, 4P, Al (Electrical Grade), 25kA, Outgoing, 63A/40A, 4P, 25kA, MCB - 8Nos, 3Phase LED kWh MFM with RS-485 for communication CL-0.5, Panel Mount - 8Nos (Wiring within the panel board for communication network of the MFMs to be part of this scope and terminals to be available in the panel for connection of cable from BMS. The MFMs and related cabling shall be fully compatible with the BMS for software integration).

2.10.1 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

2.10.5 : Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Triple pole and neutral

2.15.3 : Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.63 amps

90.11.1.13 : Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required

4.1.4 : Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.300 mm width X 50 mm depth X 1.6 mm thickness

90.16.3.9 : Supply and clamping the following size of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 X 3 mm GI flat duly painted or heavy duty GI spacer saddles spacing of clamps not exceeding 1 m, making good the damages, colour washing etc. as required ( for horizontal run) 25 x 3 Copper strip

90.12.1.34 : Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil). 3 1/2X 185 sq. mm cable

90.12.1.35 : Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in ground including excavation of trench of size 35 x 75 cm, refilling the trench etc. as required but excluding sand cushioning and protective covering (in ordinary soil). 3 1/2X 240 sq. mm cable

9.1.27 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 185 sq. mm (57mm)

9.1.29 : Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.3 1/2X 240 sq. mm (62mm)

od83408/2021_2022 : 400 A TPN Tap off box for compact rising mains including all accessories

2.2.18 : Providing and fixing following rating and breaking capacity and pole MCCB with thermomagnetic release and terminal spreaders in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required400 Amp, 50 KA, 4 pole

ELV SYSTEM

od66938/2021_2022 : &quot;SITC of 6W RMS Ceiling Speakers with inbuilt 100V Line Matching Transformer, wide opening angle, optimized for music &; speech applications with powder coated back box, supports as per specifications;- Max Power: 8W,Rated Power: 6Watts, Power Tapping: 6/3/1.5W;- Effective frequency range(-10 dB) : 150 Hz to 15KHz;- SPL at rated power (1Khz at 1 m) 108 dB Opening Angle 1 KHz / 4 KHz (-6 dB): 180/45

od66948/2021_2022 :Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required Speaker Cable Single Pair, 2-core, 1.5 sqmm

od66947/2021_2022 :IP Dome camera 2 MP HD 1080P with 1/3 CCD/CMOS, Progressive/De-interlace, Very High Definition resolution (1920x1080), Dual streaming, 25 FPS, min one H.264 stream & one H.264/MPEG 4 stream compression support, 2.7-12mm lens, 0.1 lux, Tamper detection with built in WDR &amp; automatic back light compensation circuitry with camera manufacturer power supply unit. The camera shall be capable of operating on both POE and an UPS power source . Camera shall be along with Suitable adaptor with 2meter cable.Camera shall be along with camera mounting pole/back box and accessories.

od66957/2021_2022 : SITC of 4-pair, Cat6 UTP Cable, roll of 305m

od66958/2021_2022 : SITC of Cat6 24-port Unloaded Angular Jack Panel, 1U

od66959/2021_2022 : RACKS WIRE MANAGERS SITC of 15U Rack Frame/Steel/Casters Type 3/Black with Levellers, Front Perforated Single Door, Rear Perforated Dual Doors, Side Vented Panels, Swing Handle

od66960/2021_2022 : SITC of 24 port Un Managed POE switch with 1GSSP port

od66961/2021_2022 : SITC of Horz. Cable Organiser/2U/ Channel On Front

od66962/2021_2022 : SITC of Server /IT Rack mount power distribution unit, 1Ph, 230V, 32A, 50/60Hz, Zero U standard with 12 X Indian Round Pin 5/15A, 16A MCB X 2 Circuits- PDU Rating 7.3KVA/Bottom feed-3Mt/ Black/ Inlet Plug Not Installed

od71986/2021_2022 : Supply, installation, testing and commissioning of Mixing Amplifier - 240W

od71987/2021_2022 : Supply, installation, testing and commissioning of 1x24 SC Adaptor Module Panel - Simplex and including all accessories like pigtails, sleeves, etc.

od71988/2021_2022 : Supply, installation, testing and commissioning of LIU 24 Port Rackmount Blank with Splice Tray and Cable spool (SC) SM and including all accessories like pigtails, sleeves, etc.

od71989/2021_2022 : Supply, laying, testing and commissioning of Fiber Optic Cable 6 core SM Indoor / Outdoor Cable including splicing and termination at both end

Cauvery Buildtech

Keechery Engg Co

Macro Enterprises

Bidder Name

thoppilcontractors(india)pvtltd

Macro Enterprises

Keechery Engg Co

Cauvery Buildtech