Construction of New Building for Government Science College at Limkheda Ta. Limkheda Dist. Dahod

New Construction Work of New Building for Government Science College Limkheda,Dist- Dahod

BILL OF QUANTITIES

Percentage Rate Tender

Item Description of Item Quantity Unit Rate In Amount

1 Excavation for foundation upto 1.5 m depth 3821.00 Cumt 125.86

including sorting out and stacking of useful

materials and disposing off the excavated stuff

upto 50 Meter lead.(A) Loose or soft soil

2 Excavation for foundation for depth from 1.5 m 1789.00 Cumt 309.04

to 3.0 m including sorting out and stacking of

useful materials and disposing off the excavated

stuff upto 50 Meter lead. (D) Soft rock not

requiring Blasting

3 Filling in foundation and plinth with sand in 435.00 Cumt 419.82

layers of 20 cm. Thickness including watering

ramming and consolidating etc. comp.

4 Filling available excavated Earth (Excluding 1814.00 Cumt 137.47

Rock) in trench plinth side of foundation . in

layer not excluding 20 cm in depth consolidation

each deposited layer by ramming and watering

5 Filling foundation and plinth with murrum or 3302.50 Cumt 273.07

selected soil in layer of 20 cm in thickness

including ramming watering and consolidating

6 Applying general insecticide pest control 2061.00 Sqmt 54.39

treatment to floors, cupboards etc including

labour materials etc. complete. Using

Imidacloprid 30.5 SCas Per IS 6313 part -II(

(0.075% concentration by mass) is

recommended 10.5ml chemical diluted with

liters of water application 0.5 litre chemical

/Sqm of surface is recommended as per I.S.

7 Providing and laying controlled cement concrete 566.23 Cumt 3861.37

M.150 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work in (A) Foundations and

8 Providing and laying controlled cement concrete 787.00 Cumt 4852.04

M.250 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work in (A) Foundations,

footings, and Mass concrete. footing

9 Providing and laying controlled cement concrete 59.50 Cumt 8278.97

M-250 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

(d) columns Up to Plinth level.

Item Description of Item Quantity Unit Rate In Amount

10 Providing and laying cement concrete 1:3:6 (1- 83.00 Cumt 3005.48

Cement : 3- coarse sand : 6- machine cut stone

aggregates 40 mm nominal size) and curing

complete excluding cost of formwork in (A)

Foundation and Plinth

11 Providing and laying controlled cement concrete 176.34 Cumt 8184.03

M-200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Columns, pillars posts and struts G.FLOOR

12 Providing and laying controlled cement concrete 66.50 Cumt 8184.03

M-200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Columns, pillars posts and struts F.FLOOR

13 Providing and laying controlled cement concrete 57.00 Cumt 8224.43

M-200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Columns, pillars posts and struts 2nd.FLOOR

14 Providing and laying controlled cement concrete 28.00 Cumt 8264.83

M-200 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Columns, pillars posts and struts 3rd.FLOOR

15 Providing and laying controlled cement concrete 691.30 Cumt 6894.26

M-250 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

Ground & Plinth BEAMS

16 Providing and laying controlled cement concrete 271.50 Cumt 5240.54

M.150 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work in (C) Plinth Slabs

17 Providing and laying controlled cement concrete 259.00 Cumt 6303.41

M.200 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work in (C) Ground floor

18 Providing and laying controlled cement concrete 252.00 Cumt 6303.41

M.200 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work in (C) First floor

19 Providing and laying controlled cement concrete 173.00 Cumt 6342.80

M.200 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work in (C) Second floor

Item Description of Item Quantity Unit Rate In Amount

20 Providing and laying controlled cement concrete 8.00 Cumt 6383.20

M.200 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work in (C) Third floor

21 Providing and laying controlled cement concrete 17.00 Cumt 6253.92

M-200 and curing etc. complete including the

cost of form work and reinforcement for

reinforced concrete work in (c) Chhajja for

22 Providing and laying controlled cement concrete 16.00 Cumt 6253.92

M-200 and curing etc. complete including the

cost of form work and reinforcement for

reinforced concrete work in (c) Chhajja for F

23 Providing and laying controlled cement concrete 11.00 Cumt 6294.32

M-200 and curing etc. complete including the

cost of form work and reinforcement for

reinforced concrete work in (c) Chhajja for S

24 Providing and laying controlled cement concrete 1.00 Cumt 6334.72

M-200 and curing etc. complete including the

cost of form work and reinforcement for

reinforced concrete work in (c) Chhajja for T

25 Providing and laying controlled cement concrete 8.50 Cumt 8794.07

M-200 and curing etc. complete including the

cost of form work and reinforcement for

reinforced concrete work in (c) Lintal for Ground

26 Providing and laying controlled cement concrete 7.50 Cumt 8794.07

M-200 and curing etc. complete including the

cost of form work and reinforcement for

reinforced concrete work in (c) Lintal for F floor

27 Providing and laying controlled cement concrete 6.00 Cumt 8834.47

M-200 and curing etc. complete including the

cost of form work and reinforcement for

reinforced concrete work in (c) Lintal for S floor

28 Providing and laying controlled cement concrete 1.00 Cumt 8874.87

M-200 and curing etc. complete including the

cost of form work and reinforcement for

reinforced concrete work in (c) Lintal for T floor

29 Providing and laying controlled cement concrete 306.00 Cumt 7768.92

M.200 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work in (C) Ground floor

30 Providing and laying controlled cement concrete 295.00 Cumt 7768.92

M.200 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work in (C) First floor Slab

Item Description of Item Quantity Unit Rate In Amount

31 Providing and laying controlled cement concrete 200.00 Cumt 7809.32

M.200 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work in (C) Second floor

32 Providing and laying controlled cement concrete 8.00 Cumt 7848.71

M.200 and curing complete including the cost of

formwork and excluding reinforcement for

reinforced concrete work in (C) Third floor Slab

33 Providing and laying controlled cement concrete 38.00 Cumt 5987.28

M-200 and curing etc. complete including the

cost of form work and excluding the cost of

reinforcement etc. complete in RCC Vertical and

horizontal wall for GF

34 Providing and laying controlled cement concrete 17.00 Cumt 5987.28

M-200 and curing etc. complete including the

cost of form work and excluding the cost of

reinforcement etc. complete in RCC Vertical and

horizontal wall for FF

35 Providing and laying controlled cement concrete 28.00 Cumt 6026.67

M-200 and curing etc. complete including the

cost of form work and excluding the cost of

reinforcement etc. complete in RCC Vertical and

horizontal wall for SF

36 Providing and laying controlled cement concrete 43.00 Cumt 6067.07

M-200 and curing etc. complete including the

cost of form work and excluding the cost of

reinforcement etc. complete in RCC Vertical and

horizontal wall for TF

37 Providing and laying controlled cement concrete 16.00 Cumt 7202.31

M-200 and curing etc. complete including the

cost of form work and excluding the cost of

reinforcement etc. complete in (E) Stair case up

to floor two level for Ground Floor to first floor

38 Providing and laying controlled cement concrete 6.00 Cumt 7202.31

M-200 and curing etc. complete including the

cost of form work and excluding the cost of

reinforcement etc. complete in (E) Stair case up

to floor two level for First to Second Floor

39 Providing and laying controlled cement concrete 6.00 Cumt 7241.70

M-200 and curing etc. complete including the

cost of form work and excluding the cost of

reinforcement etc. complete in (E) Stair case up

to floor two level for Second to Third Floor

Item Description of Item Quantity Unit Rate In Amount

40 Providing and fixing 120 cm high Stainless steel 49.00 Rmt 3719.83

railing made from anticorrocive 304 grade S S

pipe of 50 mm dia (16Gauge) as hand rail with S

S 304 grade Baluster of 38 mm dia (16Gauge) as

a vertical support fixed in RCC slab at 1.2m c/c

including three horizontal S S pipes of 25 mm

dia (16Gauge) at eqal distance fixed by

mm dia (16Gauge) S S pipe with baluster

including accessories as per detailed drawing as

directed etc. complete.

41 Providing and fixing Stainless Steel Hand Railing 40.00 Rmt 1969.50

made from anticorrocive 304 grade S S pipe of

50 mm dia (16 Gauge) as hand rail with S S

grade Baluster of 40 mm dia (16 Gauge) as a

vertical support fixed in RCC member at 1.2m c/c

S S pipe with baluster including accessories as

per detailed drawing as directed etc. complete.

42 Providing IS Mark TMT FE 500D bar 488842.00 Kg 77.77

reinforcement for RCC work including bending &

placing in position complete up to All floor Level

43 Brick work using common burnt clay building 218.00 Cumt 3853.23

bricks having crushing strength not less than

Kg./Sq.m. in foundation and plinth in cement

mortar 1:6 (1 cement:6 fine sand) (b)

44 Brick work using common burnt clay building 590.50 Cumt 4141.66

bricks having crushing strength not less than

Kg./ Sqm. in cement mortar 1:6 ( 1 cement :

Fine sand ) in super structure above plinth level

upto floor two level ( for G.F ) Conventional

45 Brick work using common burnt clay building 261.00 Cumt 4141.66

bricks having crushing strength not less than

Kg/Sq.cm. in super structure in cement mortar

1:6 (1cement : 6 fine sand) {First FLoor}

46 Brick work using common burnt clay building 206.00 Cumt 4180.47

bricks having crushing strength not less than

Kg/Sq.cm. in super structure in cement mortar

1:6 (1cement : 6 fine sand) {SF FLoor}

47 Brick work using common burnt clay building 19.00 Cumt 4219.29

bricks having crushing strength not less than

Kg/Sq.cm. in super structure in cement mortar

1:6 (1cement : 6 fine sand) {TF FLoor}

48 Half brick masonry in common brunt clay 508.00 Sqmt 645.73

building bricks having crushing strength not less

than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-

Cement : 4 -coarse sand ) in foundation and

plinth (B) Conventional for G floor.

Item Description of Item Quantity Unit Rate In Amount

49 Half brick masonry in common brunt clay 511.00 Sqmt 645.73

building bricks having crushing strength not less

than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-

Cement : 4 -coarse sand ) in foundation and

plinth (B) Conventional for FF floor.

50 Half brick masonry in common brunt clay 331.00 Sqmt 651.63

building bricks having crushing strength not less

than 35 Kg/Sq.Cm. in Cement mortar 1:4 (1-

Cement : 4 -coarse sand ) in foundation and

plinth (B) Conventional for 2nd floor.

51 Providing 15mm thick cement plaster in single 3367.00 Sqmt 184.61

coat on Rough (Similar)side of single or half

brick walls for interior plastering upto floor two

level and finished even and smooth in (ii)

Cement mortar 1:4 (1-cement :4-sand) 1x1cm

Groove at Jaunction. For GF

52 Providing 15mm thick cement plaster in single 3140.00 Sqmt 184.61

coat on Rough (Similar)side of single or half

brick walls for interior plastering upto floor two

level and finished even and smooth in (ii)

Cement mortar 1:4 (1-cement :4-sand) 1x1cm

Groove at Jaunction. For FF

53 Providing 15mm thick cement plaster in single 2689.00 Sqmt 212.49

coat on Rough (Similar)side of single or half

brick walls for interior plastering upto floor two

level and finished even and smooth in (ii)

Cement mortar 1:4 (1-cement :4-sand) 1x1cm

Groove at Jaunction. For SF

54 Providing 15mm thick cement plaster in single 559.00 Sqmt 240.38

coat on Rough (Similar)side of single or half

brick walls for interior plastering upto floor two

level and finished even and smooth in (ii)

Cement mortar 1:4 (1-cement :4-sand) 1x1cm

Groove at Jaunction. For TF

55 Providing 10 mm. Thick Mala plaster in single 2713.00 Sqmt 192.42

coat for plastering on ceiling and soffits of stairs

and finished in : (I) Cement mortar 1:4 (1

cement : 4 sand) with Mala finished of neat

cement slurry etc. complete.Ground Floor

56 Providing 10 mm. Thick Mala plaster in single 2290.00 Sqmt 192.42

coat for plastering on ceiling and soffits of stairs

and finished in : (I) Cement mortar 1:4 (1

cement : 4 sand) with Mala finished of neat

cement slurry etc. complete.F Floor

57 Providing 10 mm. Thick Mala plaster in single 1759.00 Sqmt 216.88

coat for plastering on ceiling and soffits of stairs

and finished in : (I) Cement mortar 1:4 (1

cement : 4 sand) with Mala finished of neat

cement slurry etc. complete.S Floor

Item Description of Item Quantity Unit Rate In Amount

58 Providing 10 mm. Thick Mala plaster in single 61.00 Sqmt 241.34

coat for plastering on ceiling and soffits of stairs

and finished in : (I) Cement mortar 1:4 (1

cement : 4 sand) with Mala finished of neat

cement slurry etc. complete.T Floor

59 20 mm Thick sand faced Double coat Gutka 8171.50 Sqmt 353.98

plaster on walls with 1x1cm grooves consisting

of 12 mm Thick backing coat of c.m. 1:3 (1

cement : 3 sand) and 8 mm Thick finishing coat

of c.m. 1:1 (1 cement : 1 sand) etc. complete. For

all height and as per pattern sample aprroved by

the architect or directed engineer in-charge

60 Providing throating or plaster drip and moulding 441.00 Rmt 44.07

to R.C.C. Chhajja.

61 Applying two coats of Birla or Asian acrylic lapy 16504.50 Sqmt 40.59

(putty) & two coats of primer of approved brand

and manufacture on new wall surface to give an

even shade including thoroughly brushing the

surface free from mortar dropping and other

foreign matter and sand papered smooth.

62 Wall painting (three coats) with plastic emulsion 9683.00 Sqmt 84.82

paint of approved brand and manufacture on

undecorated wall surface to give an even shade

to colour including throughly brushing the

surface free from mortar droppings and other

foreign matter and sand papered smooth.

63 Painting (two coats) with plastic emulsion paint 6821.00 Sqmt 90.48

of approved brand and manufacture on

undecorated ceiling surface to give an even

shade to colour including throughly brushing the

surface free from mortar droppings and other

foreign matter and sand papered smooth.

64 Wall Painting (Two coats) with weather proof 7943.50 Sqmt 122.14

100 % acraylic emulsion (Apex or equivalent

type) paint of approved brand and manufacture

and of required shade on exterior wall surface to

give an even shade over and including primery

coat with Alkaly resistance primer of approved

brand after thoroughly brushing surface to

remove all dust and remains of loose powdered

material etc. copm. for all height

65 Providing and laying controlled cement concrete 49.39 Cumt 8201.20

M-200 for RCC work and curing complete

including the cost of form work but excluding the

cost of reinforced concrete work in coping on

Item Description of Item Quantity Unit Rate In Amount

66 Providing and laying controlled cement concrete 6.00 Cumt 8201.20

M-200 for RCC work and curing complete

including the cost of form work but excluding the

cost of reinforced concrete work in coping on

67 Providing and laying controlled cement concrete 4.00 Cumt 8241.60

M-200 for RCC work and curing complete

including the cost of form work but excluding the

cost of reinforced concrete work in coping on S

68 Providing and laying controlled cement concrete 1.00 Cumt 8282.00

M-200 for RCC work and curing complete

including the cost of form work but excluding the

cost of reinforced concrete work in coping on T

69 Providing and fixing extruded aluminum window 375.00 Sqmt 2140.33

having extruded aluminum Colour Powder

Coated section frame main outer size 127mm x

Kg/mt,horizontal Four track member size

Kg/mt,vertical member of size 122.20mm x

31.75mm x 1.50mm ,@ Wt. 1.398 Kg/mt with

sliding shutters of horizontal member size 40mm

x 18mm x1.29mm @ wt.of 0.456Kg/mt,vertical

member of size 40mm x 18mm x 1.29mm @

wt.of 0.456Kg/mt,@ with 5 mm thick

transparent bronze colour tinted float glass with

powder coated aluminum fittings and fixtures

and transparent silicon sealant glass fixing to

frame as per details etc complete for window.

70 Providing and fixing window having extruded 10.90 Sqmt 1713.70

aluminum Colour anodized section frame main

outer size 63.50 x 38.10 x 1.95 mm,@ Wt

Kg / Rmt, horizontal two track member size

Kg/mt, vertical member of size 61.85 mm x

31.75mm x 1.30 mm @ wt.of 0.659 Kg/mt with

sliding shutters of horizontal member size 40mm

x 18mm x 1.29mm @ wt.of 0.456Kg/mt, vertical

member of size 40mm x 18mm x 1.29mm @

wt.of 0.456Kg/mt, @ Wt. 0.457 Kg/mt with

mm thick transparent bronze colour tinted float

glass with powder coated aluminum fittings and

fixtures and transparent silicon sealant glass

fixing to frame as per details etc complete for

Item Description of Item Quantity Unit Rate In Amount

71 Providing & Fixing in position standard extruded 35.00 Sqmt 1834.16

approved colour anodised Aluminum

Window/Ventilation with outer frame (of Jindal

Section No.21458,@ Wt0.650 kg/Rmt ) with

3mm thick Bajari figure adgesteble tinted

louvers glass fixed to alluminium strip blade

including fixtures, fastenning, labours and

equipments as per detailed drawing as directed.

For Ventilators

72 Providing and fixing 12mm thick toughened 246.00 Sqmt 4585.40

glass fixed panel partition with machine

polished arris edges on all sides, fixed with

anodized aluminum U-channels (top, bottom and

sides) of size 25mm x 25mm x 1.5mm thickness,

including silicone gaskets, ,all necessary

accessories, complete surface preparation using

appropriate cleaners and primers, proper

handling and positioning of glass panels

including all labor for installation, finishing and

clean-up, all complete as per specifications and

directions of the Engineer-in-charge.

73 Providing & Fixing in position standard extruded 3.00 Sqmt 2148.27

approved colour anodised Aluminum

Window/Ventilation with outer frame (of Jindal

Section No.21458,@ Wt0.650 kg/Rmt ) with

6mm thick Dark glass fixed to alluminium strip

blade including fixtures, fastenning, labours and

equipments as per detailed drawing as directed.

For Ventilators

74 Providing and fixing anodized aluminium section 222.00 Sqmt 4082.42

door frame equivalent to Jindal Section No.

including internal wooden inserts for firm grip of

hinges and hardware. Door shutter shall be

double shutter type, solid core flush door,

finished with 1 mm thick laminate on both sides.

The work includes fixing with stainless steel

handle, floor spring, and all necessary S.S.

hardware and accessories complete as per

drawing and direction of engineer-in-charge.

Item Description of Item Quantity Unit Rate In Amount

75 Providing and fixing FRP frame size 100 x 50 mm 46.00 Sqmt 2362.39

and 35 mm thick FRP depress panel

Double/Single shutter having extra

reinforcement on sides & edges in Gel coat

finish.The core of the both shutter & frame is to

be filed up with injected fire retradat grade

polyurethene foam done in situ along with

embeded wooden pieces for stiffening & also

taking hinges & fintures.The whole FRP frame &

double shutter is to be waterproof, weatherproof

,termite proof & resistance to mild

acid/alkali.Rates are to be inclusive of S.S hinges

with necessary screws & alluminum fixtures &

fastenings & fartener sleeve.Colour and Shade

approved by Engineer-In-Charge.

76 Providing and fixing 12mm thick compact 11.00 Sqmt 5835.15

laminate panel door made of high pressure

laminate with phenolic resin core and decorative

melamine surface on both sides, with stainless

steel butt hinges , mortise lock set with lever

handles, SS Door Handle , door closer as

required, all necessary stainless steel screws,

fasteners, , door hanging and final adjustments

for proper operation, all complete as per

specifications, approved samples and direction

of Engineer-in-charge.

77 Providing and fixing anodized aluminum section 13.50 Sqmt 3735.99

frame equivalent to Jindal Door Section No.

19552 with weight not less than 1.1 kg/meter

(frame size 38mm × 63.5mm), including double

shutter pivoted flush door with floor spring, solid

core finished with 1mm thick lamination on both

sides, complete with stainless steel handle and

other stainless steel fixtures, including all

necessary hardware, fasteners, adhesives,

aluminum cleats, weather strips, EPDM gaskets,

silicon sealant as required, including cutting,

fabrication, installation and final adjustments for

proper operation, all complete as per

specifications, approved samples and direction

of Engineer-in-charge.

78 P & L 60x45 cm Mirror polished Blue Kota Stone 4701.50 Sqmt 1121.80

slab flooring over 20 mm (average)thick base of

cement mortar 1:6 (1-cement 6-coarse sand) or

L.M 1:1.5 (1 Lime putty : 1.5 coarse sand laid

over and jointed with grey cement slurry mixed

with pigment to match the shade of slab

including rubbing and polishing etc.complete (A)

Item Description of Item Quantity Unit Rate In Amount

79 Providing and laying polished kota stone slab 220.00 Sqmt 1205.60

25mm thick in risers of steps,skirting Dedo and

pillars laid on 10mm thick cement mortar 1:3 (1-

Cement : 3 coarse sand) and jointed with gray

cement slury mixed with pigment to match the

shade of slab including rubbing and polishing etc.

80 Providing and laying Ceramic tiles 6mm thick in 168.50 Sqmt 1017.30

flooring treads of steps and landing laid on a bed

of 12mm thick cement mortar 1:3 (1 cement : 3-

coarse sand ) finishing with flush pointing in

81 Providing and laying coloured glazed tiles of the 472.00 Sqmt 1523.67

size 300 mm x 200 mm x 8 mm / 300 mm x

mm x 8 mm in skirting, risers of steps and dedo

on 10 mm. thick cement plaster 1:3 (1 cement :

coarse sand) & jointed with white cement slurry.

82 Providing and laying machine cut free edge 116.00 Sqmt 817.09

Polished Kota Stone Slab Green. 25 mm thick

finished treadsin with 1cm projecting, nozing

rounded moulding in tread laid over 12 mm (av.)

thick bases of cement mortar 1:6 (1-cement : 6-

coarse sand) jointed with grey or colour cement

slurry including rubbing and polishing incl.

making Three No.s of grooves of size 3mm X

3mm along the length of treads etc. complete

83 Providing and laying water proofing treatment 2236.50 Sqmt 779.70

with broken chine mosaic flooring for terrace

using 12 mm to 20 mm broken pieces of glazed

tiles to be laid over cement mortar 1:3 to plain or

slope and to be tempered to bring mortar

creme out upto surface using white cement

including rounding off junctions and extending

them upto 15 cm along the wall, clearing with

water and oxalic acid etc. as directed.

84 Providing and laying cement concrete flooring 2236.50 Sqmt 355.69

1:2:4 (1-cement : 2-coarse sand : 4-graded stone

aggregate 20mm nominal size) laid in one layer

and finished with a floating coat of neat cement.

(B) 50mm thick.

Item Description of Item Quantity Unit Rate In Amount

85 Providing Plinth Protection to Building including 299.00 Sqmt 2484.20

excavation in ordinary soil and laying cement

concrete 1:3:6 using stone aggregates of 40mm

nominal size in foundation layer 125 mm thick+

125mm thick sand layer below pre-cast Rubber

Dye inter locking concrete block 60mm thick

with grade of concrete M300 pneumatic

compressed by mechanically pressed and as per

approved design including 75mm Sand layer

for levelling and filling the joint with sand in

proper line and level etc. complete, Including

Providing and fixing pre-cast concrete kerb stone

of grey cement based concrete block 30cm

length, 30cm height and 15cm thick made of

M250 grade concrete as per approved design

and including excavation for fixing in proper line

and level, filling the joint with C:M 1:3

(1cement:3 fine sand) etc. complete.

86 Providing and fixing mirror polished Marble Slab 632.50 Sqmt 1354.41

18 to 20 mm with full round edge and polished

of approved quality in clading on sill and around

the doors/ windows/ ventilation with 12 mm

thick cement mortor CM (1:4) and fixing with

cement slurry & adhesive including moulding of

exposed edges as directed by engineering in

charge etc. complete.

87 Providinfg and fixing Safty grills of required 18590.00 Kg 159.78

pattern for windows/ Door using necessary M.S

angle/ M.S pipe, M.S flats and other structural

steel at required spacing including cutting,

welding and fabriction etc. including one coat of

primer of approved quality and two coats of oil

painting as per detail drawing etc complete.

88 Providing erecting and fixing double coated 20000.00 Litre 3.95

Syntex PVC. (ISI) water tank of required capacity

each with all necessary fittings and connection

etc. complete on terrace.

89 Providing laying and jointing in true line and 60.00 Rmt 195.67

level 50mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as

approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every

two metre C/C or shall be concelled as directed

including necessary fittings etc. including testing

of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

Item Description of Item Quantity Unit Rate In Amount

90 Providing laying and jointing in true line and 80.00 Rmt 148.12

level 40mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as

approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every

two metre C/C or shall be concelled as directed

including necessary fittings etc. including testing

of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

91 Providing laying and jointing in true line and 240.00 Rmt 91.84

level 25mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as

approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every

two metre C/C or shall be concelled as directed

including necessary fittings etc. including testing

of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

92 Providing laying and jointing in true line and 210.00 Rmt 72.65

level 15mm dia. U.P.V.C. Pipe ( SCH- 40) for cold

water including fittings make PRINCE /

SUPREME / ASTRAL / FINOLEX or equivalent as

approved by Engineer In Charge. Pipe shall be

fixed on the wall with the help of clamp at every

two metre C/C or shall be concelled as directed

including necessary fittings etc. including testing

of pipe and joints and fixing the same with

adhesive solvent, including cost of all materials.

93 Providing, laying and jointing in true line and 40.00 Rmt 834.38

level 160 diametre U.P.V.C (Type B) conforming

to IS 13592-1992 with one end plain and other

end socketed with rubber ring, & fittings

conforming to ISI 14735-1999 of approved make

for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant,

pipe shall be fixed on wall using of PVC clamp of

the size 160 mm diametre x 210 mm length x

196 mm heigh at every 2000 mm center to

center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes

etc. including testing of pipes and joints and

jointed with adhesive solvent cement including

cost of all materials.

Item Description of Item Quantity Unit Rate In Amount

94 Providing laying (to level or slopes) and jointing 597.00 Rmt 677.93

reinforced concrete Light duty non-pressure

pipes I.S. class NP2 of the following internal

diameter with collars and butt ends prepared for

collar joints including testing of joints

95 Providing, laying and jointing in true line and 282.40 Rmt 897.79

level 110 diametre U.P.V.C (Type B) conforming

to IS 13592-1992 with one end plain and other

end socketed with rubber ring, & fittings

conforming to ISI 14735-1999 of approved make

for drainage system pipe line, pipe shall be

jointed with each other with rubber lubricant,

pipe shall be fixed on wall using of PVC clamp of

the size 110 mm diametre x 149 mm length x

145 mm heigh at every 2000 mm center to

center or shall be concealed in walls as directed

including necessary fittings such as bends, shoes

etc. including testing of pipes and joints and

jointed with adhesive solvent cement including

cost of all materials.

96 Providing, laying and jointing in true line and 40.00 Rmt 777.70

level 75 mm dia. UPVC SWRType B pipe

conforming to IS 13592-1992 with one end plain

and other end socketed with rubbering and

fitting conforming to ISI 14735-1999 of

approved make for drainage system pipe line,

pipe shall be jointed with each other with rubber

lubricant, pipe shall be fixed on wall using of PVC

clamp at every 2000 mm c/c or shall be

conceled in walss as directed including necessary

fittings such as bends, shoes etc. including testing

of pipes and joints and jointed with adhesive

solvent cement including cost of all materials.

97 Providing and fixing in PVC SWR cowel went 2.00 No 15.66

75mm dia to pipes.(B) 75mm dia.

98 Providing and fixing in PVC SWR cowel went 12.00 No 28.79

110mm dia to pipes.(B) 110mm dia.

99 Providing and fixing PVC SWR Nahni trap IS 33.00 No 600.23

14735 for drain - 100 mm diameter with jali of

the following nominal diameter of self cleansing

design with C.I scread down or hinged grating

including the cost of cutting and making good the

Item Description of Item Quantity Unit Rate In Amount

100 Providing and fixing wash down water closet 15.00 No 2853.25

(European type W C pan) with integral P and S

trap including jointing the trap with soil pipe in

cement mortar 1:1 (1 cement five sand)

including providing and fixing plastic seat cover

for wash down WC with CP brass hinges and

rubber buffers back plastic seat with a pair of C I

or MS bracket with complete fitting such as lead

valve siphon 15 mm dia brass ball valve with

polythene float CP brass handle unions and

couplings for connection with inlet out let and

over flow pipes 40 mm dia porcelain enameled

flush bend including cutting holes in walls and

making good the same connection the flush bend

with cistern and closet vitreous china.

101 Provision and fixing water closet squatting orissa 6.00 No 1849.31

type W.C. pan size 580mm integral footrest and

100 mm P or S trap and in cluding 25 mm dia CP

brass flush valve and GI inlet connection etc.

comp. (A) Vitreous china long pattern white or

102 Providing and fixing stainless steel grab 22 cm x 6.00 No 1492.78

60 cm for handicapped toilet

103 Providing and fixing brass screw down stop 48.00 No 205.83

tap.(A) 15mm dia

104 Providing and fixing washbasin with single hole 15.00 No 2081.61

for pillar tap with C.I. or M.S. brackets painted

white including sutting holes and making good

the same including Brass waste, and M I fisher

union fittings including pvc connection and

waste pipe & all necessary fittings For All Floor

(A) Vitreous China:(ii) Flat Back washbasin

mm x v 400mm size. (i) In white colour

105 Providing and fixing 600mm x 450mm bevelled 12.00 No 859.41

edge mirrror of superior glass mounted on 6mm

thick A.C. sheet or plywood sheet and fixing to

wooden pluge with C.P. brass screws and

106 Providing and fixing ball cock of approved. 2.00 No 189.84

quality as directed.(A) Copper Metal (ii) 50mm

107 Providing and fixing screw down bib taps of 15.00 No 186.83

following size.(A) Brass screw down bib tap

polished bright. (i) 15mm dia.

108 Providing and fixing C.P. brass towel rail comlete 9.00 No 616.42

with C.P. brass brackets fixed to wooden plugs

with C.P. brass scews.(B) 600mm x 20mm size.

Item Description of Item Quantity Unit Rate In Amount

109 Providing and fixing in position 300 mm high, 100.00 No 707.00

150 mm wide English letters made from 1.0 mm

thick stainless steel sheet as directed by

Engineer in charge with all necessary tools &

plants etc. complete.

110 Providing and laying (two level or slopes) and 120.00 Rmt 531.04

jointing with stiff mixture of Cement Mortar in

proportion 1:1, Salt glazed stone ware pipes of

pipes 150mm laying lime concrete 1:2:4 (1-Lime

putty :2-Fine samd : 4-Graded brick aggregates

40mm nominal size) bedding for stoneware

pipes of following internal diameters with

necessary formwork and curing complete.

111 Providing and fixing S.W. gully trap with C.I. 6.00 No 1246.92

grating brick masonry chamber and water tight

C.I. cover with frame of 300mm x 300mm size

(inside) with standard weight (i) Square mouth

traps (B) 150mm x 100mm size P or R type

112 Constructing brick masonry chamber for 34.00 No 3454.79

underground C.I. Inspection chamber and bends

with briocks having croshing strength not less

than 35Kg. Cm2 in C.M. 1:5 precast RCC cover

455mm x 610mm intenal dimensions with frame

(R.C.C. top slabe with 1:2:4 mix (1-cement :2-

coarse sand :4-graded stone aggregate 20mm

size) foundation concrete 1:5:10 inside plaster

15mm thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on

walls and bed concrete etc. complete (i) Inside

dimensions 455mmx 610mm and 450mm deep

for single pipe line.

113 Constructing brick masonry chamber for 20.00 No 4258.97

underground C.I. Inspection C.I. Inspection

chamber and bends with briocks having croshing

strength not less than 35Kg. Cm2 in C.M. 1:5

precast RCC cover 500mmx 700mm intenal

dimensions with frame (R.C.C. top slabe with

1:2:4 mix (1-cement :2- coarse sand :4-graded

stone aggregate 20mm size) foundation concrete

1:5:10 inside plaster 15mm thick with cement

mortar 1:3 finished smooth with a floating coat

of neat cement on walls and bed concrete etc.

complete (i) Inside dimensions 500mmx 700mm

and 450mm deep for single pipe line.

114 Extra over items for every additional depth of 10.00 Each 242.39

0.1M. of part thereof beyond 450mm depth for

Brick masonry chamber.(i) for 455mm x 610mm

Item Description of Item Quantity Unit Rate In Amount

115 Extra over items for every additional depth of 10.00 Each 264.86

0.1M. of part thereof beyond 450mm depth for

Brick masonry chamber.(i) for 500mm x 700mm

116 Providing and fixing MS Ladder of required 300.00 Kg 126.15

pattern with MS flats(30x3mm) or round or

square bars (12mm) at required spacing & with

round headed bolts and nuts or screws or

welding including primer coat of approved

quality and two coats of oil paintas as directed

by engineer in charge

117 Providing and fixing in position 150 mm high, 100.00 No 404.00

English letters made from 1.0 mm thick stainless

steel sheet as directed by Engineer in charge

with all necessary tools & plants etc. complete.

118 Constructing drinking/Handwash Platform of 14.00 Sqmt 9602.07

18 mm thick Polished Black Granite having

0.45m width and 0.60m height including 0.60m

support at every 0.7m c/c with cementing

Materials / adhsives including makeing

necessary grooves in walls including Wash Basin

Snow White size 400x400x135mm including

Polyamide braided connection pipe 12mm dia,

450mm length Wast coupling with ceramic Pop-

up push type (Full thread) 32mm Dia Cat. No.

F8050351 with all fitting inlet and outlet

connection and all required fitting accessories

etc. with all labour material of approved quality

incl. full moulded round front edge granite strip

of one side polished and jointed with grey

cement slurry including rubbing and polishing

etc. complete for all floors

119 Providing and fixing Urinal of approved quality 12.00 Nos 1674.15

including connection with trap and with integral

longitudinal flush pipe.(A) Squating plate pattern

white earthenware 550mm x 300mm.

120 Providing and fixing polished 18 mm thick black 8.00 Sqmt 2897.69

granite with full round edge and double side

polished of approved quality in between urinal

and fixing with cement slurry & adhesive

including moulding of both exposed edges as

directed by engineering in charge etc. complete.

121 Charges for making holes from 50mm to 160 mm 100.00 No 858.50

dia in RCC wall, slabs or any other RCC members

or Brick work by diamond core cutting machine

of HILTI or equivalent including disposing the

debris. For all floors .

Item Description of Item Quantity Unit Rate In Amount

122 Providing and fixing coloured self adhesive PU- 81.00 Sqmt 4586.41

Tactile tile, ground surface indicators of

Polyurethane) of size 300mm x 300mm for

guiding/warning to the visually visitors in the

centre/side of the pedestrian/approach pathway

as per specification and guidelines complete in

all respect to the entire satisfaction of in charge.

123 Providing and fixing 150 mm wide, approved 1215.00 Sqmt 368.65

quality chicken wire mesh at junction of brick

work and RCC work or two dissimilar surfaces, at

all heights fixed by nails, rowal plugs or tag by

cement mortar 1:3 before applying the plaster,

including curing, scaffolding all complete as

124 Providing and fixing acrylic multilingual Braille 36.00 Nos 1696.80

(raised dots) DIRECTIONAL SIGNBOARDS of size

225 x 150mm designed as per accessibility

standards and having 3.5mm thick acrylic base

plate with Upper Case San Serif words made of

white acrylic non glare cut out letters of height

15mm raised not less than 0.8mm above base

plate and the equivalent word written in Hindi

with Devanagari non glare acrylic letters of

height 15mm raised not less than 0.8mm above

base plate and having a non-glare acrylic cut

arrow pointing in the required direction. Each

signboard to be fixed as per manufacturers

specifications on the wall at the approved

location and at a height of 1200mm from FFL

complete as per design / specifications and

guidelines as per the entire satisfaction of the

Engineer-in-charge

125 Providing And filling with good quality 14.00 cumt 555.50

sinder(steam coal) as directed by engineer in

charge in sunks in layers of 15 cm thick,including

watering,placing ,ramming well etc as directed,

Item Description of Item Quantity Unit Rate In Amount

126 Providing & Fixing tactile layout plan of size 1.00 Nos 33027.00

900mm x 600mm as approved design, made of

3.0mm thick acrylic non glare base plate and non

glare cut out symbols with Braille on which

individual facility points, like inquiry, reception,

restrooms, medical room / first aid, cafeteria or

breakout area, lounge, meeting room, conference

room etc. present the respective floors with

pictograph wherever needed all in tactile raised

by minimum of 1.0mm to 2mm in various

colours to make it legible for seniors, partial

vision impaired etc. All the facility names should

be in Braille, along with English or Hindi. The

entire block of tactile signs should be mounted

on wall for easy reading. The map to be installed

at specified locations and installed at a height of

800mm from ground level complete in all

respect as per Harmonized guideline &

satisfaction of Engineer in charges.

127 Providing and fixing of acrylic, non-glare, tactile 1.00 Nos 43480.50

audio pictorial building layout as per the

approved size, design and make, having 3mm

thick acrylic non glare base plate of the approved

colour and non-glare acrylic cut out symbols

raised 3mm above base plate and Grade 2/

Grade 1 Braille to be integral with the sign face

and be raised 0.5mm above base plate. The map

to be installed at the specified location as per

accessibility standards, shall be oriented to the

position of the viewer and to be installed at a

height of 800 mm from the finished ground/

floor level and using the necessary hardware

specified by the manufacturer and to be installed

up to the height of 800 mm from the finished

ground/ floor level and using the necessary

hardware specified by the manufacturer and to

be installed complete as per

design/specifications and guidelines as per the

entire satisfaction of the the Engineer-in-charge

128 Providing & fixing Braile indicator of size 170 120.00 Rmt 820.12

mm x 35mm for handrails of the approved

design and make have braile dots raised 0.5 mm

above base plate to be installed at specific

locations as per direction of engineer in charge

Item Description of Item Quantity Unit Rate In Amount

129 Providing and fixing of conspectus tape 50mm 120.00 Rmt 1247.35

width on of treads in staircase including cutting

pasting etc. As per harmonised guidelines

complete in all respect to the entire satisfaction

of engineer in charge.

130 Providing and fixing eco-friendly light weight 1923.00 sqmt 1674.15

calcium silicate false ceiling tiles having Tegular

edge & 15 mm Thick Densified edges on the Tile

Periphery for Extra Strength The Light weight

calcium silicate ceiling tiles shall have , light

reflection 85% noncombustible as per B.S.

part IV, 100% humidity resistance and also

having thermal conductivity0.043° w/m KC.for

the best thermal Insulation . The Light weight

calcium Silicate tile shall be of approved texture

Fine fissured/ Spintone/Cosmos having NRC

value of 0.5 & Globe having NRC value of

NRC or equivalent of size 595 X 595 mm to be

laid on true horizontal level suspended inter

locking metal grid of hot dipped galvanized steel

sections (galvanizing @120 grams per sqm

including both side) consisting of main ‘T’ runner

suitably spaced at joints to get required length

and size of 24X38mm made from 0.30 mm thick

(minimum) sheet, 1200mm centre to centre, and

cross ‘T’ of size 24X28mm made out of 0.33mm

(Minimum) sheet spaced 1200mm along spaced

between main ‘T’ at 600mm centre to centre to

form agrid of 1200X600mm and secondary cross

’T’ of length 600mm and size 24x28mm made of

0.30 mm thick (Minimum) sheet to be

interlocked at middle of the 1200X600mm panel

to form grid of size 600X600mm resting on

periphery walls/partitions

131 Providing and on a perimeter

fixing C.I. Manhole wall

cover 0.60 M. x 1.00 Nos 958.17

0.45M. size having weight not less than 35Kg.

132 Providing & erecting open well horizontal mono 1.00 Nos 39632.40

block pump set with cast iron body, complete for

three phase submersible motor having [H]For

H.P,3 phase open well horizontal mono block

pump set suitable for 1000 LPM to 1140 LPM @

20 to 39 MTR head suitable for 65/80 mm dia

Item Description of Item Quantity Unit Rate In Amount

133 Supplying & erecting approvedmake 3 phase 1.00 Nos 19695.00

motor control cubicalpanel (Star-Delta) made

from 16G.CRCA sheet duty painted with epoxy

powder painted inside and outside with hinged

doors and locking arrangement, consisting

suitable size of ON-OFF isolator (AC- 3/23duty)

main fuses,single phasing preventer cum water

level, Guard(Compe unit), Toggle switch to by

pass Single phase preventercum WLG,indicating

lamps forR-Y-Bphases, over load relay.Automatic

water level controller, Ammeter &Voltmeter

each with two way selector switch incoming

wires duty socket Crimped,Panel to be erected

on angle iron frame grouted on wall as overload

relay,thermal/Electronics star delta cutoff

timer,start-stop push buttons.The isolator

overload relay &cntractors ofL&T,Siemens or

Cuttler Hamer make only.Panel to be erected on

angle iron frame ground on wall (e)S/D upto

134 Providing and fixing rolling shutters of approved 5.00 Sqmt 3554.40

make made of 80 mm wide M.S laths inter-locked

together through heir entire length and jointed

together at the ends by end locks mounted on

specially designed pipe shaft with bracket

plates,guide channels and arrangement for inside

and outside locking with push-pull operation

including the cost of hood cover and sprig

etc.complete(A) Shutters having width below

135 Drilling pilot borehole of size 250/300 mm at 100.00 Rmt 853.25

above site by mud flush direct rotery rig.

136 Reaming of 250/300 mm dia.Pilot borehole to 15.00 Rmt 527.95

size 550 mm dia. Incliding assembling ,lowering

housing ,casing strainerpipers with gravel

packing and clayball packing etc.

137 Development of cach water bearingzone coming 1.00 Job 13212.90

across the full depth of tubewell by lowering

mm dia.Droplineand 32 mm dia airline for each

water bearing Zone with suitabale capacity air

compressar up to avilability of sand free

138 900 CFM /200 PSI capacity air compressar upto 1.00 Job 27206.17

the availability of sand free discharge for upto

139 Supply of M.S. E.R.W. plain end medium duty 100.00 Rmt 2440.64

pipe confirming to IS 4270/2001 with latest

amendments Of size 250 mm dia (minmum

thicknes of 7.1 mm)

140 Screen Slotting of MS ERW balnce pipe with size 200.00 slots 0.22

of slot 6.75 cm X 6.35 cm X 3.12 mm for 250 mm

Item Description of Item Quantity Unit Rate In Amount

141 Supply of miscellenious bore material suitable to 1.00 Pair 1912.70

250 mm dia pipes as following (A) MS Bore

clamps made from M.S. plate with 3 holes on

either side with nuts & bolts of std make of size

900X100X16 mm flat suitable for 250 mm dia

142 Supply of miscellenious bore material suitable to 1.00 No 1385.64

250 mm dia pipes as following (B) MS Bore Plug

having 100mm height made from M.S. plate with

3 holes at equal distance on circumferrence for

nut-bolts type, locking arrrangement with nuts-

bolts & lock nuts of std make complete from

mm thick M.S. plate suitable for 250mm dia pipe.

143 Supply of miscellenious bore material suitable to 1.00 No 999.90

250 mm dia pipes as following (C) MS Bail Plug

having length 0.45 mtr from medium class pipe

as per I.S. suitable for 250 mm dia pipe.

144 Supply of miscellenious bore material suitable to 168.00 NO 86.21

250 mm dia pipes as following (D) Steel bent

plate suitable for ERW pipe for 250mm dia

(size:200 X 150X6 mm)

145 Supply of GRAVEL OF selected size 4 mm to 6mm 40.00 Cum 2020.24

146 Electrologging of Pilot bore hole with carting. 1.00 Job 10665.60

147 Geohydrological ground water investigation 1.00 No 14220.80

including vehicle charges for three phase DTH

bore/DR tube well including water sample

testing & chemical analysis

148 Providing, supplying and commissioning ISI 1.00 No 4753.30

mark CI D/F Reflux Valves of following class and

diameter including all taxes, insurance,

transportation, freight charges, octroi, inspection

charges, loading, unloading, conveyance to

departmental stores stacking etc. complete.

Reflux valves PN 1 IS 5312 with ISI mark size:

149 Providing and laying in trenches galvanised mild 100.00 Rmt 919.80

steel tubes (Midium grade) of the following

nominal bore, and tube fitting (Earthwork in

trenches to be measured and paid for separately

Item Description of Item Quantity Unit Rate In Amount

150 Constructing Manhole with R.C.C. top slab in 5.00 No. 11042.74

1:2:4 mix (1-cement :2-coarse sand : 4-graded

stone aggregate 20mm nominal size) foundation

concrete 1:3:6 mix (1-cement : 3- coarse sand :6-

Brick bats 40 + 50mm size) inside plastering

15mm thick with Cement Mortar 1:3 (1-Cement :

3-coarse sand) finished with a floating coat of

neat cement and making channels in cement

concrete 1:2:4 mix (1-Cement :2-Coarse sand :4-

stone aggregate 20mm nominal size) finished

smooth complete including curing and festing (i)

Inside size 900mm x 1200mm and 1.5M. deep

including C.I. cover with frame size 560mm

diameter total weight of cover and frame to be

not less than 128 kgs. (Wt. of cover 64 Kg. and

Wt. of frame 64 Kg.)(A) With 230mm thick walls

of brick msonry using brick having crushing

strength not less than 35Kg. / Sq.cm. in Cement

Mortar 1:5 (1- Cement: 5- Coarse sand) (1) A

type depth 0.90 Metre for 150mm diameter

151 Providing and fixing and floor 10.0 Kg. F/Cm2 166.00 Rmt 339.05

working pressure poluthene pipes of the

following outside Dia. Low densidy, complete

with special falnge compression type fittings,

wall clipsetc. including making good the wall

ceiling and floor.(G)110 mm

152 Providing and fixing and floor 10.0 Kg. F/Cm2 40.00 Rmt 696.90

working pressure poluthene pipes of the

following outside Dia. Low densidy, complete

with special falnge compression type fittings,

wall clipsetc. including making good the wall

ceiling and floor.(G)180 mm

153 Providing junction for rain water juncton 4.00 Nos. 8633.48

chamber of size 0.60x0.60x0.75m with

excavation of size 1.96x1.96 m & 0.15m thick

c.c.1:2:4 bed concrete including brick masonary

wall in CM 1:6 of 0.75m height & 0.23m thick

with 15mm thick cement plaster inside & outside

& 1.06x1.06 RCC (1:2:4) slab of thickness 0.15m

with CRS steel and 0.60mx0.45m cast iron

manhole cover with frame weight not less than

35 kg as per directed by Engineer-in-charge

Item Description of Item Quantity Unit Rate In Amount

154 Providing and installation Recharge pit of 2.00 Nos. 109645.60

“RAIWOHA” Make 3 layer RCC Precast Injection

well system of size 1.5 meter Dia. X 3.4 Meter

Height rein forced concrete precast three layer

module with 6” dia x 12” dia. V wire screen of

0.75mm x 1.0 mm Slot size in SS 304 material

and 1.0 meter height with MS Top cover and

required Air vent including all necessary

excavation and transportation at site including

required filter media for the recharge system as

per site requirement.

155 Drilling of min. 250 mm dia. bore hole in all 100.00 Rmt 1252.32

strata including dualover burden strata by

combination DR/DTH rig including lowering

mm dia MS ERW pipes in bore hole and testing

etc.all work as per directed engineer incharge.

156 Supplying slotted PVC pipes of approved quality 100.00 Rmt 555.50

at site of work confirming to IS. 1239/1974

157 Construction of granular sub-base 150 mm thick 345.80 Cum 1609.94

by providing coarse graded machine crushed B.T.

material satisfying MOST specification of grading

I (B.T. stone aggregate 53 mm to 26.5 mm 35 %,

26.5 to 4.75 mm - 45 % and 2.36 mm below -

% )including spreading in uniform layer with

motor grader on prepared surface, mixing by mix

in place method with rotavator at OMC and

compacting with vibratory roller to achieve the

desired density etc. complete.

158 Steel work, welded in built up sections framed 31449.00 kg 90.55

work including cutting, hoisting, fixing in

position and applying a priming coat of read lead

paint & two coat oil paint. (A)In beams and joists,

channels angles Tees, flats, with connecting

plates or angle cleats as in main and cross beams.

Hip and jack rafters, purlins conneted to

common rafters and the like..

Item Description of Item Quantity Unit Rate In Amount

159 Providing and fixing of Ridge flashing for roof 792.00 Sqmt 858.67

panel shall be made out of 0.5 mm thick pre

coated GI sheet . The Precoated sheet shall be of

minimum 240 mpa steel grade confirming to IS

14246:1995 and shall have zinc coating of

minimum 120 gsm as per IS:277:1992 , 5-7

microns epoxy primer on both side of the sheet

and polyester top coat 15-18 micron. The PPGI

Sheet shall have plastic protective guard film of

minimum 25 microns to avoid scratches during

transportation. The ridge shall be fixed to the

steel members by pop rivet or self drilling/self

stitching fastners @ maximum 450 mm c/c along

length of capping/flashing etc complete .

160 Providing and fixing pre-cast Rubber Dye / steel 1803.00 Sqm 689.20

Dye inter locking concrete block 60mm thick

with grade of concrete M300 pnumatic

compressed / vibrated mechanically and as per

approved design Confirming to IS 15658 :

including 35 mm Sand layer for levelling and

filling the joint with sand in proper line and level

as per guidlines of IRC : SP 63-2018 etc.

161 Providing and fixing pre-cast concrete kerb stone 494.00 Rmt 370.83

of gray cement based concrete block 30cm

ength,30cm height and 15cm thick of M250

grade concret as per approved design and

including excavation for fixing in proper line and

level,filling the joint with C:M 1:3 (1cement:3fine

sand) etc complete.

162 Box cutting the road surface to proper slope and 737.00 Cum. 112.02

camber for making a base for road work

including removing the excavated stuff and

depositing on the road side slope as directed

upto upto All lift and lead..

163 Providing, laying and compacting natural sand & 108.00 Cum. 683.77

gravel[ C.B.R. not less than 20%] below sub base

course including carriage of materials spreading

in uniform layer manually on prepared base and

compacted with vibratory roller to achieve

desired density including all materials, labour

164 Providing and laying wet mix macadam base 313.00 Cum. 1679.63

course 250 mm thick in two layers using

machine crushed B.T. chips as per required

gradation mixing with required optimum

quantity of water, conveying the mix to site of

work, spreading in to grade and camber with

mechanical paver and consolidation each layer

with vibratory roller including cost of material

labour plant and equipment etc. complete.

Item Description of Item Quantity Unit Rate In Amount

165 Compaction and finishing of cement concrete 1026.00 Sqm 65.65

road by trimix process providing extra Labour

charges for the trimix vacume dewatering

service process on cement concrete road sutface

by using vacuum dewatering pump floater

surface vibrator including making groves and

rough finish to surface including leveling etc

166 Providing and fixing concertina coil fencing with 860.00 Rmt 864.56

punched tape concertina coil 600 mm dia 10 mt

openable length having 50 no rounds per 6 mt

length, upto 3mt height of wall with existing

angle iron (50mm x50mm x5mm )requird

shaped As per Directed Engeenier in charge.

placed 2.4mt or 3.00mt apart and with

horizontal R.B.T. reinforced barbed wire(3 mm)

stud tied with G.I. staples and G.I. clips to retain

horizontal, including necessary bolts or

G.I.barbed wire tied to angle iron, all complete as

per direction of Engineer-in-charge, with

reinforced barbed tape (R.B.T.)/Spring core (2.5

mm thick) and weight 43.478 gm/meter at

compound wall for ESR M4/ intakewell.

167 Constructing providing and fabricating cattle 5.00 Sqmt 5056.06

guard using channel section frame of size ISMC

series 100 mm x 50 mm (Weight 9.20 kg/Rmt)

and ISMC section 100 mm x 75mm (weight

kg/Rmt) intermediate support for welding

G.I.pipe at 12 Cm C/C of size 50 mm in a frame

made of Channel section size 100 mm x 50 mm

all round including fixing the unit on prepared

chamber of masonary wall using MS hold fast

embeded in masonary wall top as directed by

Engineer in charge and as per drawing and

necessary required arrangement etc complete.

168 Supplying of well rotted FYM manure with all 38.00 Cum. 378.75

lead and Lift including spreading mixing dressing

and rolling with hand roller etc. complete.

169 Scarifying the surface of Soil including spreading 1495.00 Sqm 26.26

of DAP fertilizer mixing with Soil properly

levelling gand dressing of the plot

170 Supplying and planting Dibbing semi carpet lawn 1495.00 Sqm 20.20

at distance of abour 15 cm x 15 cm after proper

anti termite teratment amd rolling the seme by

hand roller amd wetering etc complete.

Item Description of Item Quantity Unit Rate In Amount

171 Bowing and developing flowering plants grown 10.00 No. 30.30

in nusery having approximate height 4 to 5 ft or

Height ad per Landscaps Plan with natural

growith of soil packed in polithyline bag or

Earthern pot. Including organic & chemical

fertilizer Pesticides, fungicides, hormones &

maintaining the plants up to three months as

deserted. Bottol palm.

172 Bowing and developing flowering plants grown 10.00 No. 60.60

in nusery having approximate height 4 to 5 ft or

Height ad per Landscaps Plan with natural

growith and nature colour planted in alump of

soil packed in polithyline bag or Earthern pot.

Including organic & chemical fertilizer pesticides,

fungicides hormones & maintaining the plants uo

to three months as deserted Trinagle Plan.

173 Bowing and developing flowering plants grown 10.00 No. 60.60

in nusery having approximate height 4 to 5 ft or

Height ad per Landscaps Plan with natural

growith and nature colour planted in alump of

soil packed in polithyline bag or Earthern pot.

Including organic & chemical fertilizer pesticides,

fungicides hormones & maintaining the plants uo

to three months as Jasud

174 Bowing and developing flowering plants grown 10.00 No. 75.75

in nusery having approximate height 4 to 5 ft or

Height ad per Landscaps Plan with natural

growith and nature colour planted in alump of

soil packed in polithyline bag or Earthern pot.

Including organic & chemical fertilizer pesticides,

fungicides hormones & maintaining the plants uo

to three months as Croton

175 Bowing and developing flowering plants grown 8.00 No. 10.10

in nusery having approximate height 4 to 5 ft or

Height ad per Landscaps Plan with natural

growith and nature colour planted in alump of

soil packed in polithyline bag or Earthern pot.

Including organic & chemical fertilizer pesticides,

fungicides hormones & maintaining the plants uo

to three months as deserted green mahindi

Item Description of Item Quantity Unit Rate In Amount

176 Bowing and developing flowering plants grown 8.00 No. 15.15

in nusery having approximate height 4 to 5 ft or

Height ad per Landscaps Plan with natural

growith and nature colour planted in alump of

soil packed in polithyline bag or Earthern pot.

Including organic & chemical fertilizer pesticides,

fungicides hormones & maintaining the plants uo

to three months as deserted New block ficus.

177 Labour charges for planting various plantsafter 56.00 No. 40.40

proper anti termite treatment in pits including

placing property and filling the pit with requred

prepared mix soil and wetering and dispporting

178 Maintance of the garder for 360 days after 1.00 Job. 10100.00

Complition of 3 month stipulated period is

completed for plantation o lawn and plants

including applying second round of proper

antitermite tretment.

179 Providnig and fixing to wall ceiling and floor 80 125.00 Rmt 447.72

Schedule Syntex / Astra (CPCV) or equivalent of

the following nominal bore tube fittings and

clamps the wall ceiling and floor (C) 40 mm

180 Providing and fixing consealed to wall, ceiling 90.00 Rmt 208.80

and floor 80 Schedule Syntex / Astral (CPVC) or

equivalent brand of the following nominal bore

tube fittings and clamps including Making goods

the wall ceilling and floor (A) 20 mm

181 Providing and fixing brass screw doen stop cock 1.00 Rmt 287.85

(A) 15 mm. Dia.

182 Rubber Hose pope 15 mm dia of approved brand 120.00 Rmt 25.25

183 Providnig and fixing G I Nipple as directed. 1.00 No. 20.20

184 Supply. installation, testing & commissioning of 1.00 No 116150.00

ISI approved electrical motor driven jockey

pump set having 10.8 m3/hr. @ 70m head. The

pump unit shall be a horizontally direct mounted

motor. Unit shall comprise the following

minimum requirements:

a) Pump, b) Electric motor IE2, c) Foundation

bolts, d) Mating flanges with gasket and

fasteners, e) Discharge gauges, etc. complete in

all respect, with labour, with GST.

185 Supply, installation, testing & commissioning of 1.00 No 60600.00

Priming tank,HDPE type, 1000 litres, with

necessary piping 100 mm size, G.I pipe for

priming the pumps, pipe of with butterfly valves

for isolation, Water Filling to priming tank by

piping min. 50 mm size, ,with all complete.

Item Description of Item Quantity Unit Rate In Amount

186 Supply, fabrication & erection of aboveground 75.00 Mtr 469.65

G.I. 'C'-Class, ERW piping, conforming to IS:1239,

part-I, Heavy class up to 150 mm dia. and

IS:3589, for size 200 mm dia. & above, thickness.

G.I. pipe fitting's as per IS: 1239, part-II, Heavy

class for size 150 mm dia. & below & IS:

for size 200 mm dia. above, flanges, nuts bolts &

washers, 3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc.

Painting for piping, fittings & structural pipe

support, shall be two coat of zinc primer and

two coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved

drawings, specicification and direction of the

Engineer-in-Charge, with all complete. 25 mm

187 Supply, fabrication & erection of aboveground 50.00 Mtr 757.50

G.I. 'C'-Class, ERW piping, conforming to IS:1239,

part-I, Heavy class up to 150 mm dia. and

IS:3589, for size 200 mm dia. & above, thickness.

G.I. pipe fitting's as per IS: 1239, part-II, Heavy

class for size 150 mm dia. & below & IS:

for size 200 mm dia. above, flanges, nuts bolts &

washers, 3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc.

Painting for piping, fittings & structural pipe

support, shall be two coat of zinc primer and

two coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved

drawings, specicification and direction of the

Engineer-in-Charge, with all complete. 50 mm

Item Description of Item Quantity Unit Rate In Amount

188 Supply, fabrication & erection of aboveground 25.00 Mtr 1388.75

G.I. 'C'-Class, ERW piping, conforming to IS:1239,

part-I, Heavy class up to 150 mm dia. and

IS:3589, for size 200 mm dia. & above, thickness.

G.I. pipe fitting's as per IS: 1239, part-II, Heavy

class for size 150 mm dia. & below & IS:

for size 200 mm dia. above, flanges, nuts bolts &

washers, 3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc.

Painting for piping, fittings & structural pipe

support, shall be two coat of zinc primer and

two coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved

drawings, specicification and direction of the

Engineer-in-Charge, with all complete. 80 mm

189 Supply, fabrication & erection of aboveground 100.00 Mtr 1994.75

G.I. 'C'-Class, ERW piping, conforming to IS:1239,

part-I, Heavy class up to 150 mm dia. and

IS:3589, for size 200 mm dia. & above, thickness.

G.I. pipe fitting's as per IS: 1239, part-II, Heavy

class for size 150 mm dia. & below & IS:

for size 200 mm dia. above, flanges, nuts bolts &

washers, 3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc.

Painting for piping, fittings & structural pipe

support, shall be two coat of zinc primer and

two coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved

drawings, specicification and direction of the

Engineer-in-Charge, with all complete. 100 mm

Item Description of Item Quantity Unit Rate In Amount

190 Supply, fabrication & erection of aboveground 8.00 Mtr 2979.50

G.I. 'C'-Class, ERW piping, conforming to IS:1239,

part-I, Heavy class up to 150 mm dia. and

IS:3589, for size 200 mm dia. & above, thickness.

G.I. pipe fitting's as per IS: 1239, part-II, Heavy

class for size 150 mm dia. & below & IS:

for size 200 mm dia. above, flanges, nuts bolts &

washers, 3 mm thick gasket, pipe hangers, etc.

Hydrostatic testing for 2 hour's at 150% of the

system pressure, hook-up etc.

Painting for piping, fittings & structural pipe

support, shall be two coat of zinc primer and

two coats of fire red conf. to IS: 5, Shade

Complete with all accessories as per approved

drawings, specicification and direction of the

Engineer-in-Charge, with all complete. 150 mm

191 Supply, installtion, testing & commissioing of 35.00 Mtr 2383.60

Underground GI (ERW) piping conforming to

IS:1239, part-I, Heavy class ('C' class) up to

mm dia. and IS:3589 Heavy class ('C' class), for

200 mm dia. & above, min. 6.35mm thickness

including Heavy class fittings, anti-corrosive tape

of size 150 mm wide x 4 mm thick, wrapping &

coating with 13KV holiday testing . Rates shall

include sand bedding of 75mm dia all around,

backfilling of the excavated including installation

of heavy pipe fitting's, flanges, etc.

10 % of all the welded joints shall be done

radiographically tested and 50% of the joints

radiographed shall be the "Field Joints".

Hydrostatic testing for 2 hours at 150% of the

system pressure, hook-up etc., complete with all

accessories as per approved drawings,

specicification and direction of the Engineer-in-

Charge, with all complete. (Road Crossing)

Item Description of Item Quantity Unit Rate In Amount

192 Supply, installtion, testing & commissioing of 6.00 Mtr 3595.60

Underground GI (ERW) piping conforming to

IS:1239, part-I, Heavy class ('C' class) up to

mm dia. and IS:3589 Heavy class ('C' class), for

200 mm dia. & above, min. 6.35mm thickness

including Heavy class fittings, anti-corrosive tape

of size 150 mm wide x 4 mm thick, wrapping &

coating with 13KV holiday testing . Rates shall

include sand bedding of 75mm dia all around,

backfilling of the excavated including installation

of heavy pipe fitting's, flanges, etc.

10 % of all the welded joints shall be done

radiographically tested and 50% of the joints

radiographed shall be the "Field Joints".

Hydrostatic testing for 2 hours at 150% of the

system pressure, hook-up etc., complete with all

accessories as per approved drawings,

specicification and direction of the Engineer-in-

Charge, with all complete. (Road Crossing)

193 Design , Supply and installation of Safety Signage 120.00 Sq. ft 1599.84

made of Zinc Sulphilde based glow in dark , Rigid

sheet with High Luminous property enclosed in a

transperent weather proof UV stabilized plastic

pasted on 3 mm thick clear acrylic sheet such as

EXITS, EMERGENCY EXIT, DO NOT USE LIFT

DURING FIRE, FLOOR MARKINGS, FIRE LIFT,

STAIRCASE EXIT, FIRE ALARM CALL POINT,

FIRE HOSE REEL, FIRE HYDRANT POINT etc.

194 Supply, installation, testing & commissioning of 3.00 No 3333.00

pressure switch. (Range 0 to 16 kg/cm2)

195 Supply, installation, testing & commissioning of 4.00 No 3232.00

150 mm dia. dial Burdon Type Glycerine Filled

pressure gauge with isolation ball valve

arrangements with necessary isolation valves

with all complete.( Range 0 to 15 kg/cm2)

196 Supply, installation, testing & commissioning of 1.00 No 6969.00

Cast iron body double flanged gate valve With

Rising Spinldle conf. to IS: 14846, PN-1.6 with

mating flanges, drilling as per IS/ANSI 150# with

mating flanges, galvanized nut, bolts & washers,

gasket 3 mm thick, etc., with all complete.

Item Description of Item Quantity Unit Rate In Amount

197 Supply, installation, testing & commissioning of 2.00 No 12120.00

Cast iron body double flanged gate valve With

Rising Spinldle conf. to IS: 14846, PN-1.6 with

mating flanges, drilling as per IS/ANSI 150# with

mating flanges, galvanized nut, bolts & washers,

gasket 3 mm thick, etc., with all complete.

198 Supply, installation, testing & commissioning of 1.00 No 18786.00

Cast iron body double flanged gate valve With

Rising Spinldle conf. to IS: 14846, PN-1.6 with

mating flanges, drilling as per IS/ANSI 150# with

mating flanges, galvanized nut, bolts & washers,

gasket 3 mm thick, etc., with all complete.

199 Supply, Installation, Testing & Commissioning of 3.00 No 2373.50

Cast iron body Butterfly valve according to IS:

13095, PN-1.6, Iron Disc for size 150 mm dia. &

below Lever operated and above 150 mm dia.

Gear operated complete with mating flanges

/ANSI class # 150 with bolts & nuts washers,

rubber gaskets 3 mm thick, etc., with all

complete. 50 mm dia.

200 Supply, Installation, Testing & Commissioning of 1.00 No 3030.00

Cast iron body Butterfly valve according to IS:

13095, PN-1.6, Iron Disc for size 150 mm dia. &

below Lever operated and above 150 mm dia.

Gear operated complete with mating flanges

/ANSI class # 150 with bolts & nuts washers,

rubber gaskets 3 mm thick, etc., with all

complete. 80 mm dia.

201 Supply, Installation, Testing & Commissioning of 3.00 No 3686.50

Cast iron body Butterfly valve according to IS:

13095, PN-1.6, Iron Disc for size 150 mm dia. &

below Lever operated and above 150 mm dia.

Gear operated complete with mating flanges

/ANSI class # 150 with bolts & nuts washers,

rubber gaskets 3 mm thick, etc., with all

complete. 100 mm dia.

202 Supply, installation, testing & commissioning of 1.00 No 6918.50

Cast iron body NRV conf. to IS: 5312, PN-1.6

complete with mating Flanges/IS/ ANSI class #

150 with bolts & nuts, washers, gaskets 3 mm

thick, etc., with all complete Accessories 50 mm

203 Supply, installation, testing & commissioning of 1.00 No 8837.50

Cast iron body NRV conf. to IS: 5312, PN-1.6

complete with mating Flanges/IS/ ANSI class #

150 with bolts & nuts, washers, gaskets 3 mm

thick, etc., with all complete Accessories 80 mm

Item Description of Item Quantity Unit Rate In Amount

204 Supply, installation, testing & commissioning of 2.00 No 10605.00

Cast iron body NRV conf. to IS: 5312, PN-1.6

complete with mating Flanges/IS/ ANSI class #

150 with bolts & nuts, washers, gaskets 3 mm

thick, etc., with all complete Accessories 100 mm

205 Supply, installation, testing & commissioning of 1.00 No 2121.00

SG iron body SinglePlate Wafer Type NRV conf.

to ASTMA 536, PN-1.6 complete with mating

Flanges class # 150 with bolts & nuts, washers,

gaskets 3 mm thick, etc., with all complete.

Accessories 100 mm dia.

206 Supply, installing, testing and commissioning of 1.00 No 4949.00

Normax make CI heavy duty ball type foot valve

with flanges, nut bolts, gaskets etc. with

necessary complete accessories. 80 mm dia.

207 Supply, installing, testing and commissioning of 2.00 No 14645.00

Normax make CI heavy duty ball type foot valve

with flanges, nut bolts, gaskets etc. with

necessary complete accessories. 150 mm dia.

208 Supply, installation, testing & commissioning of 3.00 No 6060.00

Two way fire brigade Inlet connection with

mm dia. stainless steel (SS304) instantaneous

male inlets with built in non return valve in each

inlet with 100 mm dia. header pipe, suitable

rubber cap and GI chain including nuts, bolts,

washers, gasket 3 mm thick, etc. with all

209 Supply, installation, testing & commissioning of 3.00 No 6413.50

Oblique pattern type stainless steel (SS 304)

single headed External Fire Hydrant Valve with

63 mm dia. female instantaneous outlet conf. to

IS: 5290, type - A, including mating flanges,

galvanised nuts, galvanised bolts/studs, washers

& gaskets 3 mm thick with all complete.

210 Supply, installation, testing & commissioning of 3.00 No 2070.50

63 mm dia. stainless steel (SS 304) Universal

Branch Pipe conf. to IS:

211 Supply & installation, testing & commissioing of 3.00 No 8221.40

Fire Fighting Hose - conf. to IS : 636, type A (type -

1), The fire hose shall be 15 m long with 63 mm

dia. stainless steel (SS 304) couplings conf. to IS:

903, at both the ends for connection with the

hydrant valve and the branch pipe.

Item Description of Item Quantity Unit Rate In Amount

212 Supply, installation, testing & commissioning of 3.00 No 2979.50

fabricated from 3 mm MS sheet, hose box of size-

450 mm x 600 mm x 250 mm - painted with Fire

Red as per IS: 5, shade no. 536 front 3 mm thick

transparent glass with lock & key, handle and

brass hinges - to accommodate one number of

mtr long hose and one number of universal

branch pipe, including supporting arrangement

with civil work.

213 Supply, Installation, testing & commissioing of 8.00 No 7575.00

Swinging type mild steel hose reel drum with

mm dia. x 30 mtr. rubber hose as per IS: 884. The

mounting stand shall be of mild steel and the

hose shall be fitted with a SS shut-off nozzle & SS

ball valve of 25 mm dia. including supporting

arrangement with all complete. accessories

214 Supplying, fixing & testing of of SS ball Valve 8.00 No 833.25

215 Supplying, fixing & testing of New Battery of 1.00 No 18685.00

diesel engine 150 Amp.

216 Supply and installation of Diesel Tank For Diesel 1.00 No 19695.00

Engine With All Accessories 100 Ltrs.

217 Supplying, filling & testing lube oil for diesel 10.00 Ltrs 378.75

218 Supply and commissioning of Oil Filter 1.00 No 833.25

219 Supplying, filling of diesel in diesel engine tank 50.00 Ltrs 75.75

220 Excavation of foundation, Lead And Liftting of 8.00 Cu. 6666.00

soil work and RCC work Mtrs

221 Filling Of Gaps Between pipe and Core Cutting 15.00 No 353.50

Hole With Chemical and Cement

222 Supply,fabrication and erection of Structure MS 300.00 Kg 90.90

Material as like Angle, C channel,I Beam Etc.

223 Supply, installation and commissioning of 30.00 Mtr 85.85

Flexible cable for 1.5 sq mm x 3 core for pressure

224 Supply, installation and commissioning of 12.00 Mtr 222.20

Copper Armour cable for 10 HP Motor - 4 sq mm

225 Supply, installation and commissioning of 24.00 Mtr 404.00

Copper Armour cable for 40 HP Motor - 10 sq

226 Supply, installation and commissioning of 20.00 Mtr 191.90

Copper Armour cable for Diesel Engine Battery

Charger - 2.5 sq mm x 3 Core

227 Supply, Filling and Fixing of approved make ABC 15.00 No 2323.00

type fire extinguisher - 6 Kg. Capacity as per

228 Supply, Filling and Fixing of approved make CO2 15.00 No 6514.50

type fire extinguisher. Capacity 4.5 Kg.

(conforming to IS-15683).

Item Description of Item Quantity Unit Rate In Amount

229 Submitting the application to obtain Fire NOC for 1.00 No 50500.00

one year to SMC Department,Providing complete

practical demonstration of fire system in

presence of fire officer and Submitting the

photographs of demonstration, refilling and

testing certificates of fire extinguisher,Obtaining

and providing certificate of FPCOR, Payment of

NOC Fees to SMC Department, Preparing the

documents of Affidavit and AMC with

Notorization And Submitting to Department,

follow up to receive NOC And Providing to R & B

Including all above expenditure.

230 Supply, Installation and commissioning of Fire 1.00 No 35350.00

Alarm Panel Conventional type, 8 loops , with

complete accessories.

231 Supply, Installation and commissioning of Audio 5.00 No 1262.50

hooters , with complete accessories.

232 Supply, Installation and commissioning of 5.00 No 1191.80

Manual Call Points, with complete accessories.

233 Cable(Armour) for Fire Alarm system 250.00 Mtr 111.10

234 Core cutting in wall and in RCC slab with size as 6.00 No 323.20

below: 40 mm dia. Hole

235 Core cutting in wall and in RCC slab with size as 2.00 No 444.40

below: 80 mm dia. Hole

236 Core cutting in wall and in RCC slab with size as 2.00 No 454.50

below: 100 mm dia. Hole

237 Core cutting in wall and in RCC slab with size as 4.00 No 707.00

below: 150 mm dia. Hole

238 Core cutting in wall and in RCC slab with size as 3.00 No 1010.00

below: 200 mm dia.

239 Supply, installation, testing & commissioning of 1.00 Set 161600.00

ISI approved electrical motor operated Kirloskar

make fire hydrant main pump set horizontal end

suction back pull out top discharge centrifugal

fire pump set with all the standard acessories,

base frame, coupling, and foundation bolts with

following specifications Model -DB 50/26, Flow-

54 m3/hr, Head-70 meter, Motor Rating -

22KW/30HP/3 ph Suc x Del - 65 x

240 Supplying, Installation, Testing and 1.00 No 483285.00

commissioning of Kirloskar make diesel engine

driven fire hydrant pump set suitable for

automatic operation and consisting of following:

horizontal type, centrifugal end suction back pull

out, top discharge pump of cast iron body &

bronze impeller with m.s.fabricated common

base plate, coupling, coupling guard, foundation

bolts etc.,as required. Model -KFE Flow-96

m3/hr, Head-70 meter, Engine - 50 HP / 3 ph Suc

Item Description of Item Quantity Unit Rate In Amount

241 Fire Hydrant Panel suitable for 10 hp Jockey 1.00 No 128775.00

pump, 40 hp (54 m3/hr @ 70 m head) main

electrical pump and 50 hp (96 m3/hr @ 70 m

head) Diesel engine operated pump A) Incomer

MCCB - 1 Nos R Y B Indication - 1 Set VAF Digital

Meter - 1 Set B) Outgoing F1 40 HP Star Delta

Starter - 1 For Main pump F2 10 HP DOL Starter -

1 For Jockey Pump F3 Auto - On / Off Diesel

Pump With Battery Charger Control Circuit With

Auto - Manual On/Off On/Off Trip Indication

On/Off Push Button C) Fabrication Dully Powder

Coated PO Red Colour, Fabricated From 14/16

SWG,GI Sheet , IP-42 Protection,-Fixed Type

Floor Mounted Cable Entry : Bottom

242 Providing and fixing a fire hydrant point 8.00 Nos 5555.00

installing a single-headed gunmetal fire hydrant

valve with instantaneous type coupling

conforming to IS:5290, mounted on a cast iron

hydrant stand post with flanged ends, including

necessary bolts, nuts, washers, and rubber

insertion. A mild steel fire hydrant box with a

glass front, lock, and key, painted with red

enamel paint, is also provided. The installation

includes a 30-meter long fire hose reel with a

mm diameter hose, complete with a shut-off

nozzle, drum, and wall mounting bracket, as well

as two 15-meter long fire hoses with 63 mm

diameter, complete with male and female

instantaneous type couplings conforming to

IS:636. Additionally, a gunmetal branch pipe

with a nozzle conforming to IS:903 and a 4-way

fire brigade inlet connection with gunmetal non-

return valves and instantaneous type couplings

conforming to IS:904 are installed. The system

includes mild steel pipes and fittings for the fire

hydrant system, with cutting, threading, welding,

and painting with two coats of red oxide primer

and two coats of synthetic enamel paint. Civil

works involve excavation, backfilling, and

making good the surface for laying the

underground fire hydrant pipeline, including

necessary supports and protection.

243 Providing and fixing a mild steel (MS) hose box 8.00 Nos 6565.00

with double doors, glass front, lock, and key,

painted with red enamel paint. The hose box is

wall-mounted, measures 600 mm x 450 mm x

250 mm (or as specified), and is designed to

securely house fire hoses and related equipment.

The double doors with a glass front allow for

easy visibility and access, while the red enamel

paint ensures high visibility and protection

against corrosion. The box includes a lock and

key for added security.

Item Description of Item Quantity Unit Rate In Amount

244 Providing and fixing a fire hose pipe to IS:636. 8.00 Nos 3535.00

The hose is designed for high-pressure water

delivery in firefighting applications and is made

of durable, flexible material to withstand harsh

conditions. The couplings ensure quick and

secure connections to hydrants and other

firefighting equipment, facilitating efficient water

flow during emergencies.

245 Providing and fixing a fire hose nozzle installing 8.00 Nos 1515.00

a gunmetal branch pipe with a nozzle

conforming to IS:903. The nozzle is designed for

attachment to a 63 mm diameter fire hose and is

made of durable gunmetal to ensure longevity

and resistance to corrosion. It features an

adjustable spray pattern to allow for both a

concentrated jet and a wide spray, enabling

effective firefighting in various scenarios. The

nozzle ensures efficient water flow and control,

making it an essential component of the fire

hydrant system.

246 Clearing and grubbing road land including 0.48 Hect. 28455.08

uprooting rank vegetation grass

bushes,shrubs,sapling and trees girth up to

mm removal of stumps of trees cut earlier and

disposal of unserviceable materials (C) By

mechanical means in area of light jungle

247 Earthwork in cuting in all sorts of soil and soft 64431.00 Cumt 129.28

murrum including conveying and spreading the

stuff, embankment as and where directed within

200meters from the end of the cutting with all

required lead and lift.(C) Above 400 Meters

upto 500 Meters.

248 Rolling of earthwork in layers with power roller 30337.00 Cumt 23.18

including filling in depressions which occur

during the process and Watering of earth work

249 Conveying and Utilized the stuff in the bank from 38097.00 Cumt 129.28

end of cutting with all required lead and lift ( C )

above 400 meters up to 500 meters

250 Providing and laying controlled cement concrete 380.97 Cumt 6034.75

M-250 and curing complete including the cost of

form work but excluding the cost of

reinforcement for reinforced concrete work in

251 Providing and filter media 600mm thick as 91.80 Sqmt 1268.86

directed at the back of Protection Wall as per

detailed specification.

252 Providing cement vata (10cm x 10cm size) 4.50 Rmt 24.28

quarter round in cement mortar 1:1 including

neat cement finishing watering etc. Complete

Item Description of Item Quantity Unit Rate In Amount

253 Providing and Fixing 6 mm thick Lexan 43.00 Sqm. 1441.90

Polycarbonate multi wall roofing sheet fixed with

hilti screw and rubber silicon sealer and

alluminium strip of size 50 x 3 mm etc complete

as directed by Engineer in charge.

254 Point wiring for Light/ Bell with 2-1.5 sq.mm & 725.00 Pt. 485.81

earth wire of 1.5 sq.mm (Green) both are of ISI

marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length, in

below type of pipe erected with 6A Modular

type switch/ bell push & accessories and earth

continuity of following type, erected on PVC/

Metallic/ Wooden box, single mounting base

frame covered with textured/ metallic/ white

front plate modules erected on/ in wall / ceiling

as per pipe erected, with necessary Lamp

holder/ ceiling rose/ H.D. Connector as directed.

(f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling

complete Cat. III [Accessories:- Havells

(Crabtree), MK, Schneider Electric, C&S, Achor

(Roma), Legrand ; Wire:- Finolex, Havells, RR

Cable, Polycab, KEI, Apar ; Pipe:- Precision, Nihir,

Anchor, Polycab, Vraj]

255 Point wiring for FAN with 2-1.5 sq.mm & earth 319.00 Pt. 674.68

wire of 1.5 sq.mm (Green) both are of .ISI

marked 1.1 KV Grade FRLS PVC insulated multi

strand copper wires up to 10 mtr length, in

below type of pipe erected with 6A Modular

type switch and hum free EME step type

electronic fan regulator mounted and

accessories with earth continuity of following

type erected on PVC/ Metallic/ Wooden box,

single mounting base frame covered with

textured/ metallic/ white front plate modules

erected on/ in wall/ ceiling as per pipe erected.

with necessary ceiling rose/ H.D. Connector as

directed. (f) with medium class Rigid PVC pipe

and accessories erected concealed in wall/

ceiling complete.Cat. III [Accessories:- Havells

(Crabtree), MK, Schneider Electric, C&S, Achor

(Roma), Legrand ; Wire:- Finolex, Havells, RR

Cable, Polycab, KEI, Apar ; Pipe:- Precision, Nihir,

Anchor, Polycab, Vraj]

Item Description of Item Quantity Unit Rate In Amount

256 Point wiring for Individual Plug with & earth 2.00 Pt. 510.05

wire of 1.5 sq.mm (Green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type

of pipe erected complete with Modular type

switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate

front plate modules erected on / in wall / ceiling

as per pipe erected with following type of

accessories. [I] For 6A Plug and 6 a switch with 2-

1.5 sq.mm Cu. Wire from nearby

switchboard/mcb db board (f) with medium

class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete Cat. III

[Accessories:- Havells (Crabtree), MK, Schneider

Electric, C&S, Achor (Roma), Legrand ; Wire:-

Finolex, Havells, RR Cable, Polycab, KEI, Apar ;

Pipe:- Precision, Nihir, Anchor, Polycab, Vraj]

257 Point wiring for Individual Plug with & earth 3.00 Pt. 745.38

wire of 1.5 sq.mm (Green) both are of ISI marked

1.1 KV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length, in below type

of pipe erected complete with Modular type

switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate

front plate modules erected on / in wall / ceiling

as per pipe erected with following type of

accessories. [II] For 16A Plug and 16 amp switch

with 2-2.5 sq.mm Cu. Wire from mcb db board.(f)

with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling

complete Cat. III [Accessories:- Havells

(Crabtree), MK, Schneider Electric, C&S, Achor

(Roma), Legrand ; Wire:- Finolex, Havells, RR

Cable, Polycab, KEI, Apar ; Pipe:- Precision, Nihir,

Anchor, Polycab, Vraj]

258 Point wiring for on board Looped Plug with 6A 129.00 Pt. 257.55

Modular type switch & 5 pin socket erected on

PVC / Metallic/Wooden box, single mounting

base frame covered with textured /

metallic/white front plate modules erected on

/ in wall / ceiling with following type accessories

Cat. III [Accessories:- Havells (Crabtree), MK,

Schneider Electric, C&S, Achor (Roma), Legrand ;

Wire:- Finolex, Havells, RR Cable, Polycab, KEI,

Apar ; Pipe:- Precision, Nihir, Anchor, Polycab,

Item Description of Item Quantity Unit Rate In Amount

259 Providing following type of Modular Type 19.00 Ea. 151.50

Accessories mounted with PVC /

metallic/Wooden box, single mounting base

frame covered with textured / metallic/white

front plate , modules erected with necessary

connections as per site situation directed by

Engineer In charge. (1)One No. SP 6 Amp. Cat.III

[Accessories:- Havells (Crabtree), MK, Schneider

Electric, C&S, Achor (Roma), Legrand]

260 Providing following type of Modular Type 19.00 Ea. 151.50

Accessories mounted with PVC /

metallic/Wooden box, single mounting base

frame covered with textured / metallic/white

front plate , modules erected with necessary

connections as per site situation directed by

Engineer In charge. (2) One No 5 pin plug Cat.III

[Accessories:- Havells (Crabtree), MK, Schneider

Electric, C&S, Achor (Roma), Legrand]

261 Providing following type of Modular Type 216.00 Ea. 25.25

Accessories mounted with PVC /

metallic/Wooden box, single mounting base

frame covered with textured / metallic/white

front plate , modules erected with necessary

connections as per site situation directed by

Engineer In charge. (7) Blank Plate Single, Cat.III

[Accessories:- Havells (Crabtree), MK, Schneider

Electric, C&S, Achor (Roma), Legrand]

262 Providing following type of Modular Type 13.00 Ea. 180.79

Accessories mounted with PVC /

metallic/Wooden box, single mounting base

frame covered with textured / metallic/white

front plate , modules erected with necessary

connections as per site situation directed by

Engineer In charge. (9) 16 Amp. SP one way

switch Cat.III [Accessories:- Havells (Crabtree),

MK, Schneider Electric, C&S, Achor (Roma),

263 Providing following type of Modular Type 37.00 Ea. 199.98

Accessories mounted with PVC /

metallic/Wooden box, single mounting base

frame covered with textured / metallic/white

front plate , modules erected with necessary

connections as per site situation directed by

Engineer In charge. (10) 6/16Amp. Universal

socket Cat.III [Accessories:- Havells (Crabtree),

MK, Schneider Electric, C&S, Achor (Roma),

Item Description of Item Quantity Unit Rate In Amount

264 Providing following type of Modular Type 24.00 Ea. 410.06

Accessories mounted with PVC /

metallic/Wooden box, single mounting base

frame covered with textured / metallic/white

front plate , modules erected with necessary

connections as per site situation directed by

Engineer In charge. (14) 6A/ 10A/ 16A/ 20A/

25A/ 32A Double Pole Modular MCB Switch

[Accessories:- Havells (Crabtree), MK, Schneider

Electric, C&S, Achor (Roma), Legrand]

265 Providing following type of Modular Type 126.00 Ea. 160.59

Accessories mounted with PVC /

metallic/Wooden box, single mounting base

frame covered with textured / metallic/white

front plate , modules erected with necessary

connections as per site situation directed by

Engineer In charge. (8) Computer RJ-45 socket

[Accessories:- Havells (Crabtree), MK, Schneider

Electric, C&S, Achor (Roma), Legrand]

266 Providing and erecting ISI mark Medium class 3810.00 Mtr. 24.24

RIGID PVC PIPES of following size complete to be

erected on/in wall or ceiling erected with

necessary PVC fittings & Junction boxes fixed

with adhesive solution & Clamps with following

dia of pipes, in approved manner as directed

(a)20 mm [Pipe:- Precision, Nihir, Anchor,

267 Supplying and laying UPVC cable trunking 48.00 Mtr. 277.75

system comprising unplasticised polyvinyl,

chloride rigid material with ignition free and

flame proof confirming BS with necessary end

caps Internal and external bend, flat bends,

coupler, tee etc..All necessary accessories and

measuring of following sizes (1) 75 mm x 50 mm

268 Providing and erecting Mains with 1.1 KV grade 3444.00 Mtr. 82.82

FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be

erected concealed in /flushed on wall/ceiling,

with 1.5 sq. mm copper conductor FRLS PVC

insulated stranded wire of green colour for earth

continuity of following size (A) With medium

class Rigid PVC pipe and accessories (b) 2 wire

2.5 sq. mm [Wire:- Finolex, Havells, RR Cable,

Polycab, KEI, Apar ; Pipe:- Precision, Nihir,

Anchor, Polycab, Vraj]

Item Description of Item Quantity Unit Rate In Amount

269 Providing and erecting Mains with 1.1 KV grade 480.00 Mtr. 112.11

FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm

copper conductor FRLS PVC insulated stranded

wire of green colour for earth continuity of

following size (A) with medium class Rigid PVC

pipe and accessories (a) 2 wire 4 sq. mm [Wire:-

Finolex, Havells, RR Cable, Polycab, KEI, Apar ;

Pipe:- Precision, Nihir, Anchor, Polycab, Vraj]

270 Providing and erecting Mains with 1.1 KV grade 30.00 Mtr. 147.46

FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm

copper conductor FRLS PVC insulated stranded

wire of green colour for earth continuity of

following size (b) 2 wire 6 sq. mm [Wire:-

Finolex, Havells, RR Cable, Polycab, KEI, Apar ;

Pipe:- Precision, Nihir, Anchor, Polycab, Vraj]

271 Providing and erecting Mains with 1.1 KV grade 540.00 Mtr. 260.58

FRLS PVC insulated ISI marked stranded Copper

conductor wire in following type of pipe to be

erected in / on wall / ceiling with 2.5 sq. mm

copper conductor FRLS PVC insulated stranded

wire of green colour for earth continuity of

following size (h) 4 wire 6 sq. mm [Wire:-

Finolex, Havells, RR Cable, Polycab, KEI, Apar ;

Pipe:- Precision, Nihir, Anchor, Polycab, Vraj]

272 Supplying & erecting approved make LAN cable 2520.00 Mtr. 47.47

of following size in existing pipe as per direction,

[C] CAT - 6 [Make:- D-link, Havells, RR Cable, KEI,

273 Providing and erecting Mains with ISI marked, 228.00 Mtr. 56.56

1.5KV grade electrolyte multi stranded, annealed

copper conductor with heat resistant PVC

insulated conforms to IS 694, IEC - 227 erected

in existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor

starters & control wiring) with required size of

copper lugs, nuts and bolts if required. (e) One

wire 6.00 sq. mm [Wire:- Finolex, Havells, RR

Cable, Polycab, KEI, Apar]

Item Description of Item Quantity Unit Rate In Amount

274 Providing and erecting Mains with ISI marked, 56.00 Mtr. 300.98

1.5KV grade electrolyte multi stranded, annealed

copper conductor with heat resistant PVC

insulated conforms to IS 694, IEC - 227 erected

in existing pipe of following size (Specifically for

control panel, relays, power switchgears, motor

starters & control wiring) with required size of

copper lugs, nuts and bolts if required. (i) One

wire 35.00 sq. mm [Wire:- Finolex, Havells, RR

Cable, Polycab, KEI, Apar]

275 Supplying and erecting Flexible PVC insulated 2242.00 Mtr. 22.22

multi strand multi core 1.1 kv grade ISI marked

copper wires of following size to be erected as

directed. (c) 1.00 Sq.mm 2 core round/ flat PVC

sheathed [Wire:- Finolex, Havells, RR Cable,

Polycab, KEI, Apar]

276 Supplying and erecting Flexible PVC insulated 248.00 Mtr. 46.46

multi strand multi core 1.1 kv grade ISI marked

copper wires of following size to be erected as

directed. (e) 1.50 Sq.mm 3 core round PVC

sheathed [Wire:- Finolex, Havells, RR Cable,

Polycab, KEI, Apar]

277 Providing & erecting Switch board for 126.00 Ea. 1133.22

Computer or electric apparatus consisting of

following modular type accessories mounted

with PVC / Metallic concealed/open box with

single mounting base frame covered with

textured/metallic /white front plate,modules

erected with necessary connections as directed,

1 no. 6A/16A universal plug-switch combined.

nos. 6A Switch, 3 nos. 6A 5 pin Plug, For Modular

Type Accessories Cat. III [Accessories:- Havells

(Crabtree), MK, Schneider Electric, C&S, Achor

(Roma), Legrand]

278 Decorative call bell Ting-tong box type 250 volts 2.00 Ea. 71.71

complete erected

Item Description of Item Quantity Unit Rate In Amount

279 Supplying and erecting LED indoor fittings with 588.00 Ea. 535.30

LEDs of wattage 0.2 Watt to 0.5 Watt assembled

on single MCPCB, with housing used as a heat

sink shall be made of thick sheet Steel

conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion

resistance with diffuser with company

mark/name 160V to 270V, Power Factor more

than 0.95, THD < 15%, CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt ,LED driver

efficiency > 85 % (fitting required LM-79 & LM-

80 Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (A)

Tube Light with integral driver (v) 36-40 Watts,

Surge-2 KV, IP-20, conventional 4 feet Cat-lll

[Make:- Phillips, Crompton, Havells, Wipro,

280 Supplying and erecting led lamps with following 24.00 Ea. 112.11

wattage capacity of 220 to 240 voltage, minimum

15000 burning hours life, 500 V in built-surge

protection,Polycarbonate diffuser, mounting

suitable for E14 / E27 / B22 lamp holders, pf >=

0.5 (A) LED Lamps integral type, with PC diffuser

suitable LAMP holder (ii) 5 to 8 watts Cat-III

[Make:- Phillips, Crompton, Havells, Wipro,

281 Supplying and erecting LED indoor fittings with 68.00 Ea. 1794.77

LEDs of wattage 0.2 Watt to 0.5 Watt assembled

on single MCPCB, with housing used as a heat

sink shall be made of thick sheet Steel

conforming to IS: 513/CRCA/aluminium

pressure die cast powder coated and high U.V. &

corrosion resistance with diffuser housed in

aluminium casted body with company

mark/name 160V to 270V,Power Factor more

than 0.95, THD < 15 %, CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt , LED driver

efficiency > 85 % ( fitting required LM-79 & LM-

80 Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (B)

LED Panel Light with provision for Plane front

frame with translucent cover fixed to housing

complete.IP20 (vi) 36 watts, 24" x 24", Surge-

2KV Cat-lll [Make:- Phillips, Crompton, Havells,

Wipro, Jaquar, Bajaj]

Item Description of Item Quantity Unit Rate In Amount

282 Supplying and erecting LED street light / Flood 39.00 Ea. 5976.17

light fittings with High power White LEDs

wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and

corrosion free High pressure die cast aluminum

housing with smooth finish powder coated and

heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than

5700K,Uniformity ratio >0.45, Luminaire

efficacy> 100 lumens/watt . LED driver efficiency

> 85 %. (fittings required LM-79 & LM-80

certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (A)

Street Light (IP-65), Surge protection -4KV

integral and ,Light must have 440VAC line supply

with over-voltage protection. (iii) Above 60 to

90 watts Cat-lll [Make:- Phillips, Crompton,

Havells, Wipro, Jaquar, Bajaj]

283 Supplying and erecting LED street light / Flood 10.00 Ea. 9647.52

light fittings with High power White LEDs

wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and

corrosion free High pressure die cast aluminum

housing with smooth finish powder coated and

heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or

embossed 160 to 270 V, Power Factor more than

Uniformity ratio >0.45, Luminaire efficacy>

lumens/watt. LED driver efficiency > 85 %.

(fittings required LM-79 & LM-80

certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.)

(B) Flood Light (IP-65), Surge protection -4KV

integral and ,Light must have 440VAC line supply

with over-voltage protection. (vii) (vi)above

to 200 watts Cat-lll [Make:- Phillips, Crompton,

Havells, Wipro, Jaquar, Bajaj]

Item Description of Item Quantity Unit Rate In Amount

284 Supplying and erecting LED street light / Flood 4.00 Ea. 4819.72

light fittings with High power White LEDs

wattage of 3 Watt and above assembled on single

MCPCB, efficiency more than 130 lm/w and

corrosion free High pressure die cast aluminum

housing with smooth finish powder coated and

heat sink extruded aluminium with diffuser and

Polycarbonate optics/ lenses, with toughened

glass with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than

5700K,Uniformity ratio >0.45, Luminaire

efficacy> 100 lumens/watt . LED driver efficiency

> 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED

fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.)

(C) Post Top Lantern LED fitting comprises of

finish cast aluminum spigot and spun aluminum

canopy fixed with opal polycarbonate, pipe

arrangement for vertical mounting driver and

accessories wired upto terminal block.IP

(ii)32-40W Cat-lll [Make:- Phillips, Crompton,

Havells, Wipro, Jaquar, Bajaj]

285 Pproviding and erecting Approved make Four 1.00 Ea. 6173.12

pole moulded case circuit breaker having

breaking capacity ICU of 25 KA. at 415 V,having

normal current rating up to 25 A to 100A. with

Fixed thermal & magnetic release suitable to

work on A.C. supply 50 c/s. with all internal

connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing. ICS=100%

of ICU only Cat III [Make:- L&T, Hager, Havells,

C&S, Siemens, Legrand, Schneider Electric]

286 Providing and erecting Approved make Four 5.00 Ea. 8055.76

pole moulded case circuit breaker having

breaking capacity ICU of 35 KA. at 415 V. having

normal current rating 125A. with Fixed thermal

& magnetic release suitable to work on

A.C.supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in

existing 16 G.M.S. housing. ICS=100% of ICU

Item Description of Item Quantity Unit Rate In Amount

287 Providing and erecting Approved make Four 3.00 Ea. 16221.61

pole moulded case circuit breaker having

breaking capacity ICU of 35 KA. at 415 V. having

Normal current rating 200A.with variable

Thermal & magnetic release suitable to work on

A.C.supply 50 c/s. with all internal connections,

spreader tinned copper & complete erected in

existing 16 G.M.S.housing ICS=100% of ICU only,

Cat III [Make:- L&T, Hager, Havells, C&S, Siemens,

Legrand, Schneider Electric]

288 Providing and erecting Approved make Four 2.00 Ea. 20946.39

pole moulded case circuit breaker having

breaking capacity ICU of 35 KA. and above at

V . having normal current rating 250A. with

variable thermal & magnetic release suitable to

work on A.C.supply 50 c/s. with all internal

connections, spreader tinned copper & complete

erected in existing 16 G.M.S. housing. ICS=100%

of ICU only, Cat III [Make:- L&T, Hager, Havells,

C&S, Siemens, Legrand, Schneider Electric]

289 Supplying & erecting approved make Four Pole 1.00 Ea. 13353.21

415V change over switch interior for panel

mounting with operating mechanism A.C.23 duty

confirming to IS for (E)250A / 320A Cat-lll

[Make:- L&T, Hager, Havells, C&S, Siemens,

Legrand, Schneider Electric]

290 Supplying and erecting triple pole & neutral 2.00 Rn. 1961.42

440V / 500V panel mounting Copper Busbars Mtr

with four equal Nos. of electrolyte bus having

current density not more than 1.6 Amp. / sq.mm

(Rated current / cross section area) duly

wrapped with colour insulating tape for phase

sequence of following current carrying capacity,

erected with necessary bus bar supports

/insulators, main cable socket to each bar,

erected in existing cubical panel with necessary

connections. (A) Suitable for 100 Amp. Capacity

291 Supplying and erecting triple pole & neutral 1.00 Rn. 3202.71

440V / 500V panel mounting Copper Busbars Mtr

with four equal Nos. of electrolyte bus having

current density not more than 1.6 Amp. / sq.mm

(Rated current / cross section area) duly

wrapped with colour insulating tape for phase

sequence of following current carrying capacity,

erected with necessary bus bar supports

/insulators, main cable socket to each bar,

erected in existing cubical panel with necessary

connections. (B) Suitable for 200 Amp. capacity

Item Description of Item Quantity Unit Rate In Amount

292 Supplying and erecting triple pole & neutral 1.00 Rn. 4909.61

440V / 500V panel mounting Copper Busbars Mtr

with four equal Nos. of electrolyte bus having

current density not more than 1.6 Amp. / sq.mm

(Rated current / cross section area) duly

wrapped with colour insulating tape for phase

sequence of following current carrying capacity,

erected with necessary bus bar supports

/insulators, main cable socket to each bar,

erected in existing cubical panel with necessary

connections. (C) Suitable for 300 Amp. capacity

293 Providing and erecting Miniature circuit breaker 224.00 Ea. 112.11

single pole 6A to 25A suitable to operate on

V A.C. system and having breaking capacity

KA to be erected in existing box. confirming to IS

8828/1996 with ISI Mark Cat.III [Make:- L&T,

Hager, Havells, C&S, Siemens, Legrand, Schneider

294 providing and erecting Miniature circuit breaker 53.00 Ea. 270.68

single pole 0.5A to 2A system and having

breaking capacity 10 KA to be erected in existing

box. confirming to IS 8828/1996 with ISI Mark

[Make:- L&T, Hager, Havells, C&S, Siemens,

Legrand, Schneider Electric]

295 Providing & erecting 240 V MCB double pole 1.00 Ea. 278.76

switch for lighting Load (B Curve) having 10 KA

breaking capacity & confirms to IS : 8828 in

existing box having following capacity (A) 6 to

Amp. Cat.III [Make:- L&T, Hager, Havells, C&S,

Siemens, Legrand, Schneider Electric]

296 Providing & erecting 240 V MCB double pole 4.00 Ea. 295.93

switch for lighting Load (B Curve) having 10 KA

breaking capacity & confirms to IS : 8828 in

existing box having following capacity (B)

Amp. Cat.III [Make:- L&T, Hager, Havells, C&S,

Siemens, Legrand, Schneider Electric]

297 Providing & erecting 415V MCB Four Pole Switch 48.00 Ea. 638.32

for Lighting Load (B curve) having 10KA

breaking capacity & confirms to IS :8828 in

existing box having following capacity (b)40

Amp. Cat.III [Make:- L&T, Hager, Havells, C&S,

Siemens, Legrand, Schneider Electric]

298 Sheets steel powder coated enclosure suitable 3.00 Ea. 176.75

for incorporating One/ Two nos. MCB. [Make:-

L&T, Hager, Havells, C&S, Siemens, Legrand,

Schneider Electric]

Item Description of Item Quantity Unit Rate In Amount

299 Providing and erecting Sheet Steel powder 2.00 Ea. 1492.78

coated MCB distribution board - flush / surface

mounted fitted with busbar, neutral link, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC

61439-1 & 3 without MCB to house appropriate

nos. of MCBs.(The DBs should be used of same

company of MCB to be used) suitable for (A)

single phase incoming and horizontal single

phase outgoing (b) sheet steel double door (IP-

43) (iv)12 way [Make:- L&T, Hager, Havells, C&S,

Siemens, Legrand, Schneider Electric]

300 Providing and erecting Sheet Steel powder 18.00 Ea. 2339.16

coated MCB distribution board - flush / surface

mounted fitted with busbar, neutral link, earth

bar and DIN rail, Conforms to IS 8623-1 & 3, IEC

61439-1 & 3 without MCB to house appropriate

nos. of MCBs.(The DBs should be used of same

company of MCB to be used) suitable for (B)

three phase incoming and single phase

horizontal type outgoing Per phase isolation

type (PPI) (b) sheet steel double door (i)4 way

[Make:- L&T, Hager, Havells, C&S, Siemens,

Legrand, Schneider Electric]

301 Providing and erecting Approved make RCCBs 4.00 Ea. 1969.50

conforming to IS: 12640 and having sensitivity of

30 mA and Short Circuit withstand capacity of

KA and suitable for operation on single phase

240 V,50Hz. having characteristic of quick action

& tripping with all advance feature & do not

incorporate any electronic component. for

following Max. rating erected as directed (i)

Amps.DP Cat. III [Make:- L&T, Hager, Havells,

C&S, Siemens, Legrand, Schneider Electric]

302 Providing and erecting Approved make RCCBs 55.00 Ea. 2235.13

conforming to IS: 12640 and having sensitivity of

30 mA and Short Circuit withstand capacity of

KA and suitable for operation on single phase

240 V,50Hz. having characteristic of quick action

& tripping with all advance feature & do not

incorporate any electronic component. for

following Max. rating erected as directed (ii)

40Amps. DP Cat. III [Make:- L&T, Hager, Havells,

C&S, Siemens, Legrand, Schneider Electric]

303 Providing and erecting Annealed bare Copper 25.00 Kg. 794.87

wire 8 to 16 SWG.

304 Providing and erecting HOT deep Galvanised 42.00 Kg. 77.77

iron strip wire 8 to 16 SWG.

Item Description of Item Quantity Unit Rate In Amount

305 Providing and erecting Pipe type earthing having 21.00 Ea. 368.65

150 cms.long and 2.5 cms. dia. galvanised iron

pipe with coupling and buch buried in specially

prepared earth pit complete with necessary

SWG earth wire.

306 For using salt and charcoal / coke as required for 21.00 Ea. 171.70

pipe type earthing.

307 Supplying & erecting earth pit of minimum bore 4.00 Ea. 4591.46

dia.150mm size approved make Earthing

Electrode consisting Pipe-in-Pipe Technology as

per IS 3043-1987 made of corrosion free hot

dipped G.I.Pipes having Outer pipe dia of 50mm

having 80-200 Micron galvanising, Inner pipe dia

of 25 mm having 200-250 Micron galvanising,

connection terminal dia of 12mm with constant

ohmic value surrounded by highly conductive

compound with high charge dissipation suitable

for following type of applications with chamber

and heavy duty cover. (A)(approved make OEM

has to submit test certificate including value of

earth resistance of installation duly stamped and

signed by agency and officer Incharge has to

ensure the value of earthing resistane mentioned

in test Certificate) & having back filling

compound of (B) Inner chemical (CCM

Compound)- Resistivity:- 0.2 ohm / meter testing

as per IEC 62561-2017, Voltage drop:- < 1 volt at

no load & dry form, Sulphar content:- <2%(C)

Back fill Compound :- Earthing compound

should be capable to retain moisture for long

time Necessary test report must be submitted by

Agency. (a) For Electrical Installation up to 440V

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

308 Providing , erecting , fabricating the M.S. 110.00 Kg. 77.77

structure as per requirement on site

incorporating proper size of M.S.

angles,square,round, flats, bars, channels,

sections complete with cutting, welding, grinding

& finishing duly painted with one coat of red

oxide with erection on site as per direction of

engineer in charge with necessary grouting,

cementing, plastering & finishing complete.

Item Description of Item Quantity Unit Rate In Amount

309 Providing & erecting weather proof, dust & 6.00 Sq. 10468.65

vermin proof, floor mounted front operated Mtr

indoor type cubical panel board necessary IP-42

and above protection as per approval from

engineer incharge made from 14 SWG thick CRC

M.S. sheet for outer body & doors, 16 SWG thick

CRC M.S.sheet for internal partitions with

necessary accesories , supporting angles/ flats

channel including cutting, bending, drilling,

welding, riveting with internal partitions & cable

alley as per requirements & instruction of

engineer-in-charge with erection of supplied

switch gears, BUSBARS, suitable size of inter

connecting PVC copper wire / copper-aluminium

strips, rubber grommets, rib, bakelite control

fuses/MCB for measuring instruments, earth bus

& earth bolts, foundation flange - bolts-base

Plates, sufficient nos. of hinged doors, handles

with locking arrangement and rubber

gasket,heavy duty end terminal

connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel

shall be painted with epoxy powder coating. (The

rates excludes the cost of switchgears, bus bars,

inter connecting mains & Copper Aluminium

strips, meters, Fuses etc. The dimension shall be

measured excluding base beams) The panel shall

be supplied with following approved

manufacturers with following size. (A) locally

310 Providing and erecting XLPE(IS:7098)(I)-88 ISI 40.00 Mtr. 92.92

armoured cable Aluminium conductor for

KV. to be laid on wall with necessary clamps or

in existing trench / pipe of following size of

cables. (B) 2 core 6 Sq. mm [Make:- Havells, KEI,

Finolex, RR Cable, Polycab, Apar]

311 Providing and erecting XLPE(IS:7098)(I)-88 ISI 28.00 Mtr. 490.86

armoured cable multistrand Aluminium

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of

following size of cables (E) 3 1/2 core 95 Sq.

mm ( 50 Sq. mm 1/2 core) [Make:- Havells, KEI,

Finolex, RR Cable, Polycab, Apar]

312 Providing and erecting XLPE(IS:7098)(I)-88 ISI 210.00 Mtr. 540.35

armoured cable multistrand Aluminium

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of

following size of cables (F) 3 1/2 core 120 Sq.

mm ( 70 Sq. mm 1/2 core) [Make:- Havells, KEI,

Finolex, RR Cable, Polycab, Apar]

Item Description of Item Quantity Unit Rate In Amount

313 Providing and erecting XLPE (IS:7098)(I)-88 ISI 1040.00 Mtr. 126.25

armoured cable multistrand / Solid Aluminium

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of

following size of cables (B) 4 core 6 Sq. mm

[Make:- Havells, KEI, Finolex, RR Cable, Polycab,

314 Providing and erecting XLPE (IS:7098)(I)-88 ISI 40.00 Mtr. 153.52

armoured cable multistrand Aluminium

conductor for 1.1 KV. to be laid on wall with

necessary clamps or in existing trench / pipe of

following size of cables (A) 4 core 16 Sq. mm

[Make:- Havells, KEI, Finolex, RR Cable, Polycab,

315 Making trench in soft soil of suitable width of 90 758.00 Mtr. 55.55

cm deep for laying cable or locating the fault all

over the run and back filling the same and

making the surface as normal ground.

316 Supplying following size of Light duty “A” Class 50.00 Mtr. 300.98

G.I . Pipe & erecting as directed by Engineer-in-

charge. (B) 50 mm dia

317 Supplying following size of Light duty “A” Class 20.00 Mtr. 696.90

G.I . Pipe & erecting as directed by Engineer-in-

charge. (D) 100 mm dia.

318 Providing & laying approved make Double 588.00 Mtr. 62.62

walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with

necessary connecting accessories of same

material at required depth in existing trench for

laying of cable. below ground / road surface for

enclosing cable (A)50 mm outer dia

319 Providing & laying approved make Double 120.00 Mtr. 137.36

walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with

necessary connecting accessories of same

material at required depth in existing trench for

laying of cable. below ground / road surface for

enclosing cable (D)120 mm outer dia.

320 Providing and, fixing heavy duty flange type 21.00 Ea. 38.38

brass cable gland with rubber ring for PVC

insulated armoured cable complete with out

going tails, insulating tape etc for following size

of cables. (B) 2 to 4 core 6 Sq. mm

321 Providing and, fixing heavy duty flange type 4.00 Ea. 131.30

brass double compression type cable gland with

rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc

for following size of cables. (D) 3 & 1/2 core

Item Description of Item Quantity Unit Rate In Amount

322 Providing and, fixing heavy duty flange type 6.00 Ea. 140.39

brass double compression type cable gland with

rubber ring for PVC insulated armoured cable

complete with out going tails, insulating tape etc

for following size of cables. (E) 3 & 1/2 core

323 Solder less crimping type Aluminium lugs 4.00 Ea. 20.20

conforming to IS suitable for cable of following

size evenly crimped with high pressure tool &

connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved

manner. (D) 35/50 Sq.mm.

324 Solder less crimping type Aluminium lugs 2.00 Ea. 25.25

conforming to IS suitable for cable of following

size evenly crimped with high pressure tool &

connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved

manner. (E) 70 Sq.mm.

325 Solder less crimping type Aluminium lugs 18.00 Ea. 40.40

conforming to IS suitable for cable of following

size evenly crimped with high pressure tool &

connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved

manner. (F) 95 Sq.mm.

326 Solder less crimping type Aluminium lugs 20.00 Ea. 45.45

conforming to IS suitable for cable of following

size evenly crimped with high pressure tool &

connected to switchgear terminals with

brass/cadmium plated nut bolts in an approved

manner. (G) 120 Sq.mm.

327 Supply, Installation, Testing and Commissioning 319.00 Ea. 2629.03

of suitable sweep, BEE 5 Star rated, Ceiling fan

with Brush Less Direct Current (BLDC)

permanent ferrite magnet Motor, class of

insulation: B, Rust free 3 nos.Aluminium blades,

2 nos. canopies, shackle kit with earthing

provision, copper winding, Power factor not <

0.9, Service Value (CMM/W) minimum 6.85, Air

delivery minimum 215 CMM, 350 RPM,230v

(tolerance as per IS : 374-2019), THD < 10%,

compitible with electronic regulator unit for

Speed Control and all remaining accessories

including safety pin, nut bolts, washers,

temperature rise = 75 degree C (Max.), suitable

for 140 to 285 Voltage and rectifier circuit with

surge, over current and overload protection ,

Hz, Single phase AC Supply, earthing etc.

Complete as required.[ Make shall be approved

by Engineer in Charge] (A) 1200 mm Sweep

(48") [make:- Crompton, Bajaj, Usha, Havells,

Item Description of Item Quantity Unit Rate In Amount

328 Supplying and erecting 19 / 20 mm. nominal 319.00 Mtr. 108.07

bore Medium Class M.S. Pipe down rod erected

duly painted for fan complete with proper

insulation without leakage and earthing.

329 Supplying & erecting fan hook box of 10 mm 319.00 Ea. 108.07

M.S. round bar bounded to the RCC bars up to

50mm length each side and pierced through a

16 Gauge M.S. box / Heavy Duty PVC box

complete erected concealed in Ceiling with

necessary finishing.

330 Providing 2.5mm.thick laminated acrylic sheet to 319.00 Ea. 18.18

cover the fan hook or Fan box.

331 Supplying & erecting approved make low noise 3.00 Ea. 1366.53

decorative exhaust fan having square frame ABS

body with inbuilt lowers & square frame. 250mm

with 1350 RPM Cat.II

332 Supplying & erecting single phase approved 40.00 Ea. 2054.34

make industrial exhaust fan suitable for medium

duty ring mounted low noise operation suitable

for medium duty having following dia size and

maximum speed in RPM [A] 305 mm dia

RPM Cat.II [Make:- Crompton, Bajaj, Usha,

Havells, Orient]

333 Supplying and erecting approved make 21.00 Ea. 8192.11

Octagonal pole made from HR sheet steel. The

pole should be made as per IS. and shall be

coated with hot dip galvanizing as per IS 2629/

2633/ 4759, suitable suspend local wind speed

with integral Junction box consist of terminal

plate of min 6mm Hylam sheet, standard profile

35mmX7.5mm Din-Rail for MCB Mounting, stud

type terminal and arrangement for cable

termination to be erected With Suitable

foundation (Included) as per details given by

manufacturer considering site requirement. (D)

6 Mtr. Long 70 mm Top X 135 mm bottom dia,

mm thickness with 200mmX200mmX12mm

base plate, 4-M20 Bolts and 600mm long J-

Bolt.Approx Pole weight 59 kg [Make:- Valmont,

Bajaj, Transrail, Jindal, Utkarsh, Ambika]

334 Supplying & erecting approved make SMC press 14.00 Ea. 515.10

moulded composite FRP. loop-in, loop-out

approx. 2mm thick box complete with Bakelite

connector strip 5way(3P+N+E),DIN rail for

mounting mob & hinged doors as per

requirement having locking arrangements with

mounting clamp with nuts, bolts & washers

suitable for erection on pole with cable clamps&

earth bolt of following size of box. (B) 250mm x

200mm x 100mm [deep]

Item Description of Item Quantity Unit Rate In Amount

335 Supplying and erecting Street light pole bracket 3.00 Ea 491.87

comprising main B Class GI pipe of

cm/require outside dia. complete with suitable B

Class G.I. sleeve tubing of approx. 45cms.length

and suitable for 76.5mm/80mm/require size of

pole top having nuts and bolts for fixing the

brackets and having spread of 0.5 mtr. Length

with 110 deg.with vertical plane and suitable

welded stiffener reducer and nipple with check

nut complete painted with one coat.of Red oxide

/ PU base primer and two coats of Aluminium /

PU paint. paint with following nos of arms. [A]

Single Arm bracket 0.5 Mtr

336 Supplying and erecting Street light pole bracket 18.00 Ea 622.16

comprising main B Class GI pipe of

cm/require outside dia. complete with suitable B

Class G.I. sleeve tubing of approx. 45cms.length

and suitable for 76.5mm/80mm/require size of

pole top having nuts and bolts for fixing the

brackets and having spread of 0.5 mtr. Length

with 110 deg.with vertical plane and suitable

welded stiffener reducer and nipple with check

nut complete painted with one coat.of Red oxide

/ PU base primer and two coats of Aluminium /

PU paint. paint with following nos of arms. [B]

Double Arm Bracket 0.5 Mtr

337 Supplying & erecting IP 55 grade following size 1.00 Ea. 3595.60

section pillar fabricated from joint less M.S. Sheet

with angle iron legs made from jointless M.S.

Angle with cable clamps to be buried in ground

to have appropriate erection to work uniform

until erected with cement concrete foundation