SPL REPAIRS TO BLDG NO MH 02 (MORTUARY AND CART SHED), MES 03 (MECHANICS QTRS), MES 03B (LATRINE), BLDG NO MES 02 (SUPERINTENDENTS QTRS) AT WEST HILL MILITARY STATION CALICUT UNDER GE (ARMY) TRIVANDRUM

Amount

Dismantling single layer Mangalore pattern tiles in roofing all as specified and directed.

Dismantling of battens for tiles, shingles etc of any size including tilting fillets all as specified and directed.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section in any position unframed work all as specified and directed.

M&L for second class hard wood in scantlings clean sawn, unframed work, as in rafters, purlins etc. timber fixed all as specified and directed.

M&L for preparing surfaces of wood and wood based materials new or old of any description and girth not otherwise described and treated with two coats of creosote oil all complete as specified and directed

S&F Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S.1161-1979 grade St.-240 as in purlins/battens/rafters complete all as specified and directed.

M&L for Providing, cement concrete (1:2:4) type B0 (using 12.5mm graded stone aggregate) in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and directed.

S&F Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions complete all as specified and directed.

S&F Pre- painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in ridge/valley gutter/roof covering/cladding to wall, fixed with self tapping screws as per manufacturers instructions complete all as specified and directed.

M&L for preparation of new steel surfaces of any description not other wise described over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide Zinc Chrome primer complete all as specified and directed.

Dismantling wall and ceiling boards or insulation boards/slabs/blankets any thickness, including frame work any type complete all as specified and directed.

M&L for GI 600 x 600 mm snap grid frame, rolled framed out of hot dipped galvanized steel sections comprising of undermentioned sections etc for grid frame including 4 mm thick non asbestos plain/designer ceiling board of texture as approved by Engineer-in-Charge, ceiling grid system as per product profile of regular T-2430 ceiling grid system of M/s Everest or equivalent in Ramco/Charminar/Amstrong complete all as specified and directed. (a) Suspended GI main runner 38 x 24 mm bulb Tee sections fixed with 4 mm dia GI bar @ 1200 mm c/c, level shall be adjusted with fly/bionet screws. (b) Placed in position cross Tee 1200 mm long and 28.8 x 24 mm bulb Tee section @ 605 mm c/c using snap grid and bionet fixing arrangement to secure main runners. (c) Ceiling GI 28.8 x 24 mm fixed with PVC Rawl plugs and GI screws tie secure with walls and all as per manufacturers instructions complete all as specified and directed.

M&L for preparation of new unplastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removing debris outside MD land complete all as specified and directed.

Dismantling of floor, hearth or wall tiling including cement mortar bedding(but not backing),removing serviceable tiles to MES store and rubbish off the premises all as specified and directed.

M&L 25mm thick PCC 1:2:4, Type B1 (using 20mm graded stone aggregate) as in flooring and finished fair and even complete all as specified and directed.

M&L for coloured joint free non skid rectified ceramic tiles, 7 to 8mm thick, area of each tile exceeding 0.18 Sqm but not exceeding 0.36 Sqm, in floors/skirting etc. set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 15mm thick screed bed or bedding layer in cement mortar (1:4) complete all as specified and directed.

M&L for coloured glazed ceramic tiles 7 to 8mm thick, area of each tile exceeding 0.09 Sqm but not exceeding 0.16 Sqm , as in vertical surface, set and jointed in neat cement slurry and pointed in coloured / white cement to match laid over and including 10 mm thick backing on stone/brick masonry surfaces in cement mortar (1:4) complete all as specified and directed.

Taking down chowkats or frames with shutters any description n exc. 1.5 Sqm each (without taking off shutters from the frame) complete all as specified and directed.

Taking down chowkats or frames with shutters any description exc. 1.5 Sqm but n.exc 4 Sqm each (without taking off shutters from the frame) complete all as specified and directed.

S & F Powder coated aluminium (minimum thickness of powder coating shall be 50 micron) frame work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P.brass/stainless steel screws, all complete as per the directions of Engineer-in-Charge.

S & F Powder coated aluminium (minimum thickness of powder coating shall be 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/neoprene gasket required (Cost of fittings shall be measured and paid separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ panelling, C.P. brass/ stainless steel screws all complete as per the directions of Engineer-in-Charge.

S & F anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge.

S&F mild steel flat iron holdfasts and similar articles conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L for PCC 1:2:4, type B1 using 20mm graded stone aggregate for fixing hold fast, coping, bed block etc including necessary form works complete all as specified and directed.

M&L for second class hardwood, plain, solid straight chowkats & frames wrought framed rebated on the solid rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

Material & Labour for 2nd class hardwood glazed and skeleton shutters, 30 mm thick open rebated and prepared to receive glass, gauze, etc., but divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars, any numbers fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); and fitted to chowkats complete all as specified and directed.

M&L for second class hardwood, plain framed panelled shutter 35mm thick (two panel) with lock rail and panel of 9mm B.W.P commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS: 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L for second class hardwood, 30mm thick Plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides (feather edged), or of veneered particle board medium density, wood particle board with commercial face veneers: supplied and fitted to chowkats framing is moulded on solid (for each side) complete all as specified and directed.

S&F Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing complete all as specified and directed

S&F Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing complete all as specified and directed.

S&F 4mm thick frosted glass, ordinary quality and glazing with oil putty in squares not exc 0.50 Sqm in each pane with putty or fixed with beads complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 200mm long aluminium anodized barrel tower bolts of extruded section fixed with stainless steel screws complete all as specified and directed.

S&F aluminium anodised sliding door bolts 300mm with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed

S&F stainless steel butt hinges medium weight; 100mm size IS 21817 marked fixed with stainless steel screws complete all as specified and directed.

S&F extruded aluminium alloy anodized handle fabricated type 150mm size fixed with stainless steel screws complete all as specified and directed.

S&F Floor door stopper Overall length of cover plate 150mm of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor etc complete all as specified and directed.

S&F in repairs Harrison rails 25mm dia, anodised aluminium alloy with fixing brackets , stops, rollers etc. complete all as specified and directed.

Taking down cement or cement lime plaster on brick/stone walls or in ceiling surfaces incl racking out joints hacking for key scrubbing down with water etc in any description complete all as specified and directed.

M&L for rendering 15mm thick in cement mortar (1:6) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

M&L for rendering 15mm thick in cement mortar (1:4) on stone masonry surfaces, finished even and smooth without using extra cement all as specified and directed .

Demolition of brick or stone / boulder masonry built in cement or cement lime mortar, including all quoins, arches, pillars etc. but excluding ashlar facings, dressed stone work and pre cast concrete articles and removing debris from the premises complete all a specified and directed.

M&L for providing pre-cast cement concrete block masonry with solid blocks, exc.10cm in width with PCC (1:3:6), type C1, using 20mm graded stone aggregate and set in cement mortar (1:6) complete all as specified and directed.

M&L complete removal of existing old treatment from wall surfaces by scrapping down and preparation of surfaces even and smooth and applying 3mm thick (two or more coats) wall care putty and applying two or more coats of acrylic smooth exterior paint of required shade (two or more coat applied @ 1.67 litre/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 Kg/10 sqm) complete all as specified and directed.

M&L complete removal of existing old treatment from wall surfaces by scrapping down and applying two or more coats of acrylic smooth exterior paint of required shade (two or more coat applied @ 1.67 litre/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 Kgs/10 sqm) complete all as specified and directed.

M&L for preparation of newly plastered surfaces even and smooth and applying 3mm thick (two or more coats) wall care putty and applying two or more coats of acrylic smooth exterior paint of required shade(two or more coat applied @ 1.67 litre/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 Kgs/10 sqm) complete all as specified and directed.

M&L for preparation of new plastered wall surfaces and applying 3mm thick wall care putty (two or more coats) for making the surface smooth and even and applying two coats of first quality acrylic distemper (ready mixed) having VOC content less than 50gm/litre of required shade and colour over a coat of primer complete all as specified and directed.

M&L for preparation of newly plastered surfaces of wall and preparing the surface even and finishing walls and applying two or more coats Acrylic smooth exterior paint of required shade (two or more coat applied @ 1.67 litre/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 Kgs/10 sqm) complete all as specified and directed.

M&L for preparation of new plastered wall surfaces and applying two or more coats of premium acrylic distemper (ready mixed) having VOC less than 50gm/litre of approved manufacturer of required shade and colour over a coat of primer complete all as specified and directed.

M&L complete removal of existing old treatment from wall surfaces by scrapping down and applying 3mm thick wall care putty (two or more coats) for making the surface smooth and even and applying two coats of premium acrylic distemper (ready mixed) having VOC less than 50gm/litre of approved manufacturer of required shade and colour over a coat of primer all as specified and directed.

M&L complete removal of existing old treatment from wall surfaces by scrapping down and applying two or more coats of premium acrylic distemper (ready mixed) having VOC less than 50gm/litre of approved manufacturer of required shade and colour over a coat of primer all as specified and directed.

M&L complete removal of existing old treatment from wall surfaces by scrapping down and applying two coats of oil emulsion distemper over a coat of wall primer complete all as specified and directed.

M&L newly plastered surfaces of wall even including sanding each layer to receive next new layer and applying two coats of oil emulsion distemper over a coat of wall primer complete all as specified and directed.

M&L complete removal of existing old treatment from wall surfaces by scrapping down and applying two coats of cement based paint over a coat of primer complete all as specified and directed.

M&L preparation of newly plastered surfaces of wall by and applying two coats of cement based paint over a coat of primer complete all as specified and directed.

M&L preparing new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer all as specified and directed.

M&L preparing old wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel painting over a coat of pink primer all as specified and directed.

S&F Rotational moulded polyethylene water storage tanks of 500 litres capacity (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I including dismantling of existing unserviceable water tank and connecting inlet and outlet pipe lines complete all as specified and directed.

S&F in repairs ball brass valves, high pressure, with polythene float and flynut complete, screwed for 20 mm bore dia iron pipe or brass ferrule complete all as specified and directed.

Taking down 15 mm bore GI tubing and connections and removing to the store complete all as specified and directed.

Taking down 20 mm bore GI tubing and connections and removing to the store complete all as specified and directed.

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 on brick wall to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting exc 10 cm and not exc 20 cm girth complete all as specified and directed.

S&F 15 mm bore unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., complete all the specified and directed

S&F 20 mm bore unplasticised PVC pipes of pressure rating 10 kgf/cm2 fixed complete to walls, ceilings or in floors etc., complete all the specified and directed

Dismantling of cast iron or reinforced concrete drain pipes of internal dia 75/100 mm, jointed in cement mortar and taking out of trenches, if required complete all the specified and directed

S&F PVC (SWR) pipes 110 mm dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all the specified and directed

S&F PVC (SWR) pipes 75 mm dia, single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all the specified and directed

S&F PVC (SWR) bends any radius for 75mm bore dia pipe with access door complete all as specified and directed.

S&F PVC (SWR) bends any radius for 110mm bore dia pipe with access door complete all as specified and directed.

S&F PVC (SWR) junction, single (Single T) equal or unequal for 110mm bore dia pipe complete all as specified and directed.

M&L for PVC (SWR) floor trap, plain with 75 mm dia of outlet grating including jointing with solvent cement complete all as specified and directed.

S&F in repairs wall hung Vitreous china premium/ 1st quality wash down water closet wall hung EWC white/ ivory/off white (closed pattern incl all necessary accessories like rag bolts/ gel gasket etc. (excluding flushing cistern & flush pipe) complete in all respect complete all as specified and directed.

S&F in repairs 10 ltrs capacity PVC valve less, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and connection to flush pipe complete all as specified and directed.

S&F in repairs flush pipe of polyethylene of low or high density or PVC 32 mm dia, for low level cistern to squat pattern closet incl all joints and making good to the floor complete all as specified and directed

S&F in repairs health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified.

S&F in repairs vitreous China wash basin, white, flat back, size 630 x 450 mm, including cutting for and pinning in ends of brackets or erecting stand but exclusive of fixing of supply and waste pipe complete all as specified and directed.

S&F 15 mm dia Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without entered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed complete all as specified and directed.

M&L for 32 mm dia waste fittings, brass, chromium plated for glazed ware sinks, wash basins, etc. with long screwed shanks and fly-nuts, flange end bedded in red lead cement and other end fixed complete all as specified and directed.

S&F PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed.

S&F in repairs 15 mm dia chromium plated fancy type Bib taps, cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed complete all as specified and directed.

S&F in repairs 20 mm dia Stop valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&F in repairs 125 mm dia brass chromium plated shower rose complete all as specified and directed.

S&F in repairs Shower arm 15 mm size, 195mm long with bend of 45degree with flange of PTMT any colour.(Minimum weight 40gms) complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

Taking down carefully copper/aluminium point wiring of light, fan, socket or power socket complete, including fittings such as switches, ceiling roses, pendants, regulators, sockets etc. and making good disturbed surfaces of walls, floor ceiling etc, match the existing complete all as specified and directed

M&L for point wiring for one light point controlled by one way switch with cable 1.5 Sqmm size PVC insulated (unsheathed) 1100 volts grade single core, stranded (multistrand) copper conductor FRLS cable and drawing in and including non-metallic rigid PVC concealed conduit medium grade inclusive of conduit fittings such as bends, tees, reducers etc and galvanised iron sheet steel terminal boxes of size 16 gauge thickness, light switches, sockets with modular white cover with frame one continuous run of 1.50 Sqmm nominal area solid conductor PVC insulated unsheathed 1100 volts grade single core FRLS cable with solid copper conductor green in colour with wire and connecting to earth dolly complete all as specified and directed.

All as per item No 90.00 here in before but for one fan point controlled by one way switch complete all as specified and directed.

All as per item No 90.00 here in before but for One 3/5 Pin, 5 Amps socket outlet on same board with other switches all as specified and directed.

All as per item No 90.00 here in before but for One 3/5 Pin, 5 Amps socket outlet on independent board all as specified and directed.

All as per item No. 90.00 on here in before but for one 3/5 pin 15 amp socket outlet on independent board using 2.5 Sqmm copper conductor for earth continuity cable complete all as specified and directed

S & F switch piano flush type, single pole, one way, 5 Amps, 240 volt including connecting up electrically complete all as specified and as directed.

S & F Socket outlet with safety shutter 5 pin, 5 Amps, 240 volt flush type complete all as specified and as directed.

S & F switch piano one way, 15 Amps, single pole flush type complete all as specified and as directed.

S & F socket outlet, poly carbonate 2 in 1, 3 pin, 5/15 Amps, flush type complete all as specified and as directed.

S&F Lamp holder, insulated body of PVC/poly carbonate type with back plate suitable for angle/batten fittings complete all as directed and directed.

S&F ceiling rose 3 terminals, insulated body of PVC/poly carbonate of size 65mm x 50mm complete all as directed and directed.

S&F stepped type electronic fan regulator, flush type, SP, 230V on the existing phenolic laminated sheet etc complete all as specified and directed.

S&F LED batten extruded aluminium body with PC diffuser in unique square shape >120 degree wide distribution, 4 feet 20 watts of minimum efficacy 120 lumen/ watts LED batten 4 feet 20 watts, CCT 6500 K complete including connection upto ceiling rose with flexible copper twin twisted wire including taking down old unserviceable light fitting complete all as specified and directed. Make : Cat part No LDO0103031, INTENS0 LXS of Policab or equivalent in Jaguar / Philips / Bajaj / Wipro / Osram / GE / Havells /MEPRO Electricals / HPL / Halonix / Goldmedal

S&F LED batten extruded aluminium body with PC diffuser in unique square shape >120 degree wide distribution, 2 feet 10 watts of minimum efficacy 120 lumen/ watts LED batten 2 feet 10 watts, CCT 6500 K complete including connection upto ceiling rose with flexible copper twin twisted wire including taking down old unserviceable light fitting complete all as specified and directed. Make : Cat part No LDO0103025, INTENS0 LXS of Policab or equivalent in Jaguar / Philips / Bajaj / Wipro / Osram / GE / Havells /MEPRO Electricals / HPL / Halonix / Goldmedal

S&F surface mounted LED bulk head luminaires 10 watts minimum efficacy 120 lumen/ watts with ABS body & polycarbonate diffuser available in CCT 6000K IP 54 including taking down old unserviceable light fitting complete all as specified and directed.

S&F submain wiring with using two single core 6.00 Sqmm copper multistranded conductor PVC insulated and unsheathed (FRLS) cable and one single core 6.00 Sqmm copper multistranded conductor PVC insulated and unsheathed (FRLS) earth wire using ISI marked IS 694, 1100 volts grade PVC insulated flexible stranded copper conductor wire drawn through with and including medium grade concealed PVC conduit ISI marked of suitable size including conduit fitting and accessories complete including cutting chases in existing wall of any description built in cement mortar and making good the disturbed surfaces in cement mortar 1:4 and finishing the surface to match with existing surface and finish termination with bottle type copper lugs conduit being laid either in ceiling slab or wall or on surfaces or under the frame of the false ceiling including PVC flexible conduit or through wooden partition including clamping arrangement as required including taking down submain wiring complete all as specified and directed. NOTE: Two runs of 6.0 sqmm copper cables and one run of 6.0 sq mm copper cable along with white colour PVC conduit with accessories will be measured as one unit length.

S&F MCB SP 6-32 Amps, 240V, breaking capacity 10 KA 'B' series 240 volts, 50 Hz complete all as specified and directed.

S&F MCB SPN 40-63 Amps, 240V, breaking capacity 10 KA 'C' series, 240 volts, 50 Hz complete all as specified and directed.

S&F MCB distribution board, double door, sheet steel powder coated DB suitable for MCBs fitted with bus bar neutral link earth bar and din rail single phase 240 volts and neutral conforms to IS 13032-1991, 4-way with 200 Amps rated bus bar, including taking down old existing one complete all as specified and directed.

S&F MCB distribution board, double door, sheet steel powder coated DB suitable for MCBs fitted with bus bar neutral link earth bar and din rail single phase 240 volts and neutral conforms to IS 13032-1991, 8-way with 200 Amps rated bus bar, including taking down old existing one complete all as specified and directed.

S&F bracket for street light fitting made out of 50 mm dia GI pipe light grade 1.50 Mtr long each bent to required shape & size as directed by Engineer-in-charge and fixed to pole with and including flat iron clamps 02 numbers made out of 25 x 4mm flat iron including GI nuts, bolts & washer and painting of clamps and street light fritting bracket with one coat of red oxide primer, one under coat and one finishing coat with aluminium paint complete all as specified and directed.

S&F 25 Watts LED street light luminaire integral type, voltage range upto 150V to 270V with one number spare LED drive of the same cap and make. LED street light shall be made up of pressure die-cast aluminium housing with black epoxy polyester powder coating for long life with including connection from overhead conductor to security light fittings with suitable length with Aluminium wire/ cable of size 2.50 Sqmm, 2 core solid conductor including taking down old unserviceable street light fitting complete all as specified and directed. Note:- 1. The luminaire shall be complete IP 66 for optical compartment and control gear Compartment. 2. The optical compartment shall be covered with heat resistant toughened glass for safety. 3. The LED street light shall be top maintainable for easy maint with multiple LEDs with out put of 100 Lum/watt. 4. The LED driver shall be isolated potted type IP-65 with constant current constant voltage topology to ensure optimum driving of LEDs. Make : Cat part No ENDURACITYLINER NEO SL 25 W LED of Havells or equivalent in Jaguar / Philips / Bajaj / Wipro / Osram / GE / Policab /MEPRO Electricals / HPL / Halonix /Goldmedal

S&F 35 Watts LED street light luminaire integral type, voltage range upto 150V to 270V with one number spare LED drive of the same cap and make. LED street light shall be made up of pressure die-cast aluminium housing with black epoxy polyester powder coating for long life with including connection from overhead conductor to security light fittings with suitable length with copper wire/ cable of size 1.50 Sqmm, 3 core solid conductor including taking down old unserviceable street light fitting complete all as specified and directed. Note:- 1. The luminaire shall be complete IP 66 for optical compartment and control gear Compartment. 2. The optical compartment shall be covered with heat resistant toughened glass for safety. 3. The LED street light shall be top maintainable for easy maint with multiple LEDs with out put of 110 Lum/watt. 4. The LED driver shall be isolated potted type IP-65 with constant current constant voltage topology to ensure optimum driving of LEDs. Make : Cat part No ENDURACITYLINER NEO SL 35 W LED of Havells or equivalent in Jaguar / Philips / Bajaj / Wipro / Osram / GE / Policab /MEPRO Electricals / HPL / Halonix /Goldmedal

S&F LED lamp 15 watts of minimum efficacy 120 lumen/ watt complete all as specified and directed.

Taking down ceiling fan, sealing cable end, dismantling blades and removing fan and blades and deposited to MES store yard complete all as specified and directed.

S&F ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) complete all as specified and directed.

M&L for taking down and dismantling old unsv ceiling fans from site and removal of burnt winding by cutting, cleaning slots and re-winding of motor for AC ceiling fan of size 1200/1400mm any make of fan with super enamelled copper winding wire of existing gauge, weight above 500 grams per fan, varnishing with E class insulation varnish. threading, including necessary laith work and connecting with appropriate size copper conductor cable upto connector block complete all as specified and directed. Notes:- (i) Motor shall be wound with machine only. (ii) Rate quoted shall be deemed to be included for dismantling and taking down of any type of fans from site for necessary repair work and refixing in the same location after repair work

S&F in replacement of old unserviceable gun metal bush of ceiling fan including necessary laith, Grinding and welding work Complete all as specified and directed by Engineer-In-Charge .

S&F replacement of old unserviceable capacitor AC 230 volts 2.5 mfd (ISI marked) complete all as specified and directed by Engineer-In-Charge .

S&F in replacement of old unserviceable ball bearing of size 6200 to 6204 including necessary laith , Grinding and welding work Complete all as specified and directed by Engineer-In-Charge . Make NBC/SKF

S&F in replacement of old unserviceable shackle assembly kit (Rubber real -01, MS split clamp two Nos, nuts and bolts washers- 2 Nos & split pin -02 Nos) suitable for ceiling fan of 1200/1400mm sweep Complete all as specified and directed by Engineer-In-Charge

S&F in replacement of old unserviceable down rod of ceiling fan of 20 mm bore "medium grade" with split pin, hanging clamp and rubber real (length of rod not less than 45cm and not more than 60cm) in white/brown colour (fully furnished) Complete all as specified and directed by Engineer-In-Charge.

Material and Labour for removing old paint by scraping down with sand paper including washing and filling cavities with filler and applying one coat of painting with synthetic enamel paint over a coat of red oxide zinc chrome primer by spray gun using spray gun method painting to ceiling fan of 1200mm sweep at site including 03 Nos blades, motor (both sides) down rod, writing MES No/ Srl No on the ceiling fans complete all as specified and directed by Engineer-In-Charge.

M&L for Earthing complete with using GI earth plate electrode 600x600x6.0 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less than 1.5 mtr below normal ground level and earth plate surrounded with adequate quantity of charcoal dust mixed with salt to a packed thickness off 15 cm all around the plate with using 4 mm dia GI Wire as earth lead moulded and retrieved to earth plate at one end and connected to main switch / control board at another end with and including 15 mm dia GI light grade from upper end of earth plate upto external face of the wall of the building including 20 mm dia bore GI pipe light grade as water pipe from chamber to upper edge of the plate GI funnel with wire mess fixed on water pipe and provision of PCC 1:2:4 type B-1 (Using 20 mm Dia graded stone aggregate) duly reinforced with mild steel round bar 6 mm dia @ 150 mm c/c both ways with 10 mm dia mild steel bars as in lifting handle with and including necessary excavation and earth work including laying the pipe concealed in floor / wall all as per plate No-3 of SSR Part-I complete all as specified and directed and testing on completion (Note:- If the desired resistance is not found earthing shall be re-done by the contractor at no extra cost to Govt) complete all as specified and directed.

lancor builders (BID ID -3159507)