CONSTRUCTION OF GOVERNMENT MEDICAL COLLEGE AND HOSPITAL AT PITHORAGARH DISTRICT PITHORAGARH

Amount

CIVIL WORKS Fertile topsoil to be stockpiled and reused Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge:All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-incharge. Ordinary rock

Hard rock (blasting prohibited)

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Extra for every additional lift of 1.5 m or part thereof in excavation / banking excavated or stacked materials. All kinds of soil.

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Supplying chemical emulsion in sealed containers including delivery as specified. Chlorpyriphos/ Lindane emulsifiable concentrate of 20%

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL anti-termite treatment (excluding the cost of chemical emulsion) : Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor: With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Suspended floors, roofs, landings, balconies and access platform.

Shelves (cast in situ)

Lintels, beams, plinth beams, griders, bressumers and cantilevers

Columns, pillars, piers, abutments, posts and struts

Stairs, (excluding landings), except spiral staircase

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 metre or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using fly ash and cement content as per approved design mix, and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. NOTE- (1) Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately. (2) Fly ash conforming to grade I of IS 3812 (Part-1) only be used as part replacement of OPC as per IS : 456. Uniform blending with cement to be ensured in accordance with clauses 5.2 and 5.2.1 of IS:456 -2000 in the items of BMC and RMC. Note :- The above item shall be used judiciously where specified quality of Fly Ash is available for mixing in concrete. Also, the guidelines issued by CDO, CPWD, vide circular no. CDO/SE(RR)/Fly Ash (Main)/102 dated 9th April 2009 shall be followed in such cases. All works up to Plinth level

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using fly ash and cement content as per approved design mix, and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. NOTE- (1) Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately. (2) Fly ash conforming to grade I of IS 3812 (Part-1) only be used as part replacement of OPC as per IS : 456. Uniform blending with cement to be ensured in accordance with clauses 5.2 and 5.2.1 of IS:456 -2000 in the items of BMC and RMC. Note :- The above item shall be used judiciously where specified quality of Fly Ash is available for mixing in concrete. Also, the guidelines issued by CDO, CPWD, vide circular no. CDO/SE(RR)/Fly Ash (Main)/102 dated 9th April 2009 shall be followed in such cases All works above plinth & up to floor V level.

Extra for providing richer mixes at all floor levels. Providing M-30 grade concrete instead of M-25 grade BMC/ RMC. (Note:- Cement content considered in M-30 is @ 340 kg/cum)

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self- centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in- Charge. (Material shall confirm to ASTM 6063). Floor Joint of 100 mm gap

Providing and fixing of expansion joint system related with wall joint (internal/ external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063). Wall Joint of 100 mm gap

Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. The Joint System shall resists damage or deterioration from the impact of falling ice, exposure to UV, airborne contaminants and occasional foot traffic from maintenance personnel. Provision of Moisture Barrier Membrane in the Joint System to have water tight joint is mandatory requirement. (Material shall confirm to ASTM 6063.) Roof Joint of 100 mm gap

Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand)

Brick work with non modular fly ash bricks conforming to IS:12894, class designation 10 average compressive strength in super structure above plinth level up to floor V level in : Cement mortar 1:6 (1 cement : 6 Coarse sand)

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab over 0.50 sqm

Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge. Granite work

Extra for fixing marble /granite stone, over and above corresponding basic item, in facia and drops of width upto 150 mm with epoxy resin based adhesive, including cleaning etc. complete.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia & length ( hold fast lugs or dash fastener shall be paid for separately). Second class teak wood

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters: 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for providing vision panel not exceeding 0.1 sqm in all type of flush doors (cost of glass excluded) (overall area of door shutter to be measured): Rectangular or square

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size).

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality. 1.0 mm thick

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Casement door with top hung ventilator with 3D and S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series) frame Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.. 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ±. 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(Area of door upto 2.50 sqm)

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension (Area of window upto 1.75 sqm).

Float glass panes 4 mm thick glass pane (weight not less than 10 kg per sqm)

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (Area of opening for glass panes excluding portion inside rebate shall be measured).

Fly proof stainless steel grade 304 wire gauge with 0.5 mm dia. wire and 1.4mm wide aperture with matching beading

Providing and fixing fire resistant door frame of section 50 x 60 mm on horizontal side & 35 x 60 mm on vertical sides having built in rebate made out of 1.6 mm thick GI sheet ( Zinc coating not less than 120gm/ m²) suitable for mounting 120 min Fire Rated Glazed Door Shutters. The frame shall be filled with Mineral wool Insulation having density min 96Kg/m³ . The frame will have a provision of G.I. Anchor fastners 14 nos ( 5 each on vertical style & 4 on horizontal style of size M10 x 80 ) suitable for fixing in the opening along with Factory made Template for SS Ball Bearing Hinges of Size 100x89x3mm for fixing of fire rated glazed shutter . The frame shall be finished with a approved fire resistant primer or Powder coating of not less than 30 micron in desired shade as per the directions of Engineer - in- charge . (Cost of SS ball bearing hinges is excluded).

Providing and fixing 60 mm thick glazed fire resistant door shutters of 120 min Fire Rating confirming to IS:3614 (Part II) or EN1634-1:1999, tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, top rail & side rail 60 mm x 60 mm wide and bottom rail of 110 mm x 60 mm made out of 1.6mm thick G.I. sheet (zinc coating not less than 120gm/m²) duly filled mineral wool insulation having density min 96 kg/ m³ and fixing with necessary stainless steel ball bearing hinges of size 100x89x3mm of approved make, including applying a coat of approved fire resistant primer or powder coating not less than 30 micron etc all complete as per direction of Engineer-in-charge (panelling to be paid for seperately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-incharge with glass of required thickness having 120 minutes of fire resistance both integrity & radiation control (EW120) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid door/window/Ceosetory window s & other Frames/Chowkhat comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non tox ic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter jo ints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum f rame density of 750 kg/cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge) , minimum compressive strength of 58 N/mm2, modulus of elast icity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixed in position with M.S hold fast/lugs/SS dash fa steners of required dia and length complete as per direction of Engineer-In - Charge . (M.S hold fast/lugs or SS dash fasteners shall be paid for separate ly). Note: For WPC solid door/window frames , minus 5mm tolerance in dimensions i.e. depth and width of profile shall be acceptable . Variation in profile dimensions on plus side shall be acceptab le but no extra payment on this account shall be made Frame size 65 x 150 mm

Providing and fixing factory made single extruded WPC (Wood Polymer Composite) solid plain flush door shutter of required size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium ca rbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/bore r proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S sc rews, all as per direction of Engineer-In­ Charge. (Not e : stainless steel butt hinges and necessary S.S screws shall be paid separately) 35 mm thick

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Steel work welded in built up sections/framed worK including cutting hoisting, rixing in position andapplying a priming coat of approved steel primer using structural steel, etc. as required. In gratings, frames, guard bar, ladders, railings, brackts. Gates & similar works.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and erecting 2.00 metre high temporary barricading at site; each panel of size 2.50mx3.00m made of 40x40x6mm angle iron or 50x50x3mm hollow MS tube posts/horizontal members/ bracings covered with 1.63mm thick MS sheet. The sheet shall be fixed with 30x5mm MS flat by suitable welding/riveting. The panels shall be made so that gap of 50cm above the ground is available making overall height as 3.5m. MS channel ISLC 75 @ 5.70 kg/m, 50cm long shall be provided at the bottom having oval shaped holes of size 50x25mm at both ends with 50cm long MS angle 40x40x6mm bracing. Suitable arrangement shall be made to fix the barricading to avoid from overturning by providing 250mm long expansion fasteners at both ends. The work shall be executed as per drawing/direction of Engineer-in-Charge which includes writing and painting, arrangement for traffic diversion such as traffic signals during construction at site for day and night, glow lamps, reflective signs, marking, flags, caution tape as directed by the Engineer-in-Charge. The barricading provided shall be retained in position at site continuously i/c shifting of barricading from one location to another location as many times as required during the execution of the entire work till its completion. Rate include its maintenance for damages, painting, all incidentals, labour materials, equipments and works required to execute the job. The barricading shall not be removed without prior approval of Engineer-in-Charge. (Note :- One time payment shall be made for providing barricading from start of work till completion of work i/c shifting. The barricading provided shall remain to be the property of the contractor on completion of the work).

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Extra for pre finished nosing to treads of steps of marble/granite stone.

Extra for marble/granite stone flooring in treads of steps and risers using single length up to 2.00 metre.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying vitrified double charged floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Thickness of tile minimum 09mm. Size of Tile 600x600 mm

Providing and laying Vitrified double charged tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. Thickness of tile minimum 09mm. Size of Tile 600x600 mm

Chequered terrazo tiles 22 mm thick with graded marble chips of size up to 6 mm in floors, jointed with neat cement slurry mixed with pigment to match the shade of the tiles, including rubbing and polishing complete, on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) : Medium shade pigment using 50% white cement, 50% ordinary cement

Providing and laying C.C. pavement of mix M-25 with ready mixed concrete from batching plant. The ready mixed concrete shall be laid and finished with screed board vibrator , vacuum dewatering process and finally finished by floating, brooming with wire brush etc. complete as per specifications and directions of Engineer-incharge. (The panel shuttering work shall be paid for separately). (Note:- Cement content considered in this item is @ 330 kg/cum. Excess/less cement used as per design mix is payable/ recoverable separately).

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. GI Metal Ceiling Lay in perforated Tegular edge global white color tiles of size 595x595 mm and 0.5 mm thick with 8 mm drop; made of GI sheet having galvanizing of 100 gms/sqm (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC (Noise Reduction Coefficient ) of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation, and backed with a black Glass fiber acoustical fleece.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on interlocking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanized butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. 8 mm thick fully perforated calcium silicate board made with Calcareous & Siliceous materials reinforced with cellulose fiber manufactured through autoclaving process to give stable crystalline structure with minimum compressive strength 225 kg/ sq. cm, bending strength 100 kg/sq. cm , of size 595x595 mm, having perforation of dia. 10 mm with minimum perforated area 18 % with non woven tissue on the back side, having an NRC ( Noise Reduction Coefficient) of 0.85, with 50 mm thick rockwool of 48 kg /cum backing.

Providing and fixing in position wall panelling at all heights with integral densified calcium silicate panels/tiles of size 595 x 595mm, having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity <0.043 W/m K as per ASTM 518:1991, comprising of a frame made from especially fabricated galvanised mild steel sheet 0.50 mm thick pressed section (galvanizing @120 grams per sqm including both sides) i.e.vertical studs of size 48 x 34 x 36 mm are placed at 600mm center to center in a floor and ceiling channel section of size 50 x 32m fixed to the floor and soffit at 600mm centers using 12mm dia,50mm long wedge type expanded zinc alloy dash fastner with 10mm bolt. This same channel is then to be fixed in horiziontal direction at 600mm center to center so as to form a grid of 600mm x 600mm. Glasswool of 50mm thickness is then to be inserted in the slots and finally calcium silicate non combustible panels/tiles are to be screw fixed with self tapping pan head nickel coated mild steel screws of size 13 x 3.2mm on to this grid leaving an even groove of 1 mm between the panels. The joints between the panels are to be duly jointed and finished using recommended jointing calcium silicate based compound and fiber join t tape roll 50mm wide (90 metre )roll and two coats of primer suitable for panelling as per manufacturer’s specification as per direction of Engineer-in-Charge all complete. With 15 mm thick fully perforated square/butt edge light weight calcium silicate panels/ tiles

Providing & fixing false ceiling at all heights with GRG (Glass Fibre Reinforced Gypsum) false ceiling tiles of Size 595x595 mm of approved texture, design and patterns having moisture content less than 2%, humidity resistance of 99%, NRC0.50 to 0.75 as per IS 8225:1987, Non combustible as per BS 476 (part 4)-1970 and light reflectance of 85% (minimum) to be laid in true horizontal level suspended on inter-locking metal T-Grid of hot dipped galvanised iron section of 0.33mm thick (galvanized @ 120 grams per sqm including both sides) comprising of main-T runners of size 15x32 mm of length 3000 mm, cross - T of size 15x32 mm of length 1200 mm and secondary intermediate cross-T of size 15x32 mm of length 600mm to form grid module of size 600 x 600 mm, suspended from ceiling using galvanised mild steel items (galvanizing @ 80 grams per sqm) i.e. 50 mm long, 8 mm outer diameter M-6 dash fasteners, 6 mm dia fully threaded hanger rod upto 1000 mm length and L-shape level adjuster of size 85x25x2 mm. Galvanised iron perimeter wall angle of size 24x24x0.40 mm of length 3000 mm to be fixed on periphery wall / partition with the help of plastic rawl plugs at 450 mm center to center and 40 mm long dry wall wood screws. The work shall be carried out as per specifications, drawing and as per directions of the Engineer-in-Charge. With semi perforated 12 mm thick micro tegular edged GRG false ceiling tiles.

Providing and fixing Heat Resistant Terrace Tiles (300 mm x 300 mm x 20 mm) with SRI (solar refractive index) > 78, solar reflection > 0.70 and initial emittance > 0.75 on waterproof and sloped surface of terrace, laid on 20 mm thick cement sand mortar in the ratio of 1:4 (1 cement : 4 coarse sand) and grouting the joints with mix of white cement & marble powder in ratio of 1:1, including rubbing and polishing of the surface upto 3 cuts complete, including providing skirting upto 150 mm height along the parapet walls in the same manner.

12 mm cement plaster : 1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)

20 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

15 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

White washing with lime to give an even shade : New work (three or more coats)

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/ 10 sqm. Over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats

Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content. With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)

Providing and supplying aluminium extruded tubular and other aluminium sections as per the architectural drawings and approved shop drawings , the aluminium quality as per grade 6063 T5 or T6 as per BS 1474,including super durable powder coating of 60-80 microns conforming to AAMA 2604 of required colour and shade as approved by the Engineer-in-Charge. ( The item includes cost of material such as cleats, sleeves, screws etc. necessary for fabrication of extruded aluminium frame work. Nothing extra shall be paid on this account). The weight of aluminium extruded section shall be taken for purpose of payment.

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including: (a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)-cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including: (b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers. (c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment, including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass. (d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight.

(e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineer- in-Charge. Note:-1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves) on the external face shall be measured in sqm. up to two decimal places.

Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NABL accredited lab or by any other accreditation body which operates in accordance with ISO / IEC 17011 and accredits labs as per ISO/ IEC 17025. 1. Performance Laboratory Test for Air Leakage Test (-50pa to - 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr. 2. Static Water Penetration Test. (50pa to 1500p) as per ASTME- 331-09 testing method for a range up to 2000 ml. 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times design wind pressure without any failure) as per ASTME-330-10 testing method for a range upto 50 mm 5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4- 09 testing method for Qualitative test, Tests to be conducted on site. 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000 ml

Providing, assembling and supplying vision glass panels (IGUs) comprising of hermetically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.25.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge.

Providing and applying integral crystalline (dry shake) of hydrophilic in nature for waterproofing treatment to the RCC structures like basement raft, foundation slab, sewage & water treatment plant slab, warehouses floor, parking structures and water tank base slab etc. sprinkled @0.60kg per sqm or higher as recommended by the manufacturer’s specification over the lean concrete of above cited structures. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e. by reducing permeability of concrete by more than 85%, compared control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline dryshake shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the Engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

Providing and laying integral cement based treatment for water proofing on horizontal surface at all depth below ground level for under ground structures as directed by Engineer-in-Charge and consisting of : (i) Ist layer of 22 mm to 25 mm thick approved and specified rough stone slab over a 25 mm thick base of cement mortar 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound conforming to IS:2645 in the recommended proportion over the leveling course (leveling course to be paid separately). Joints sealed and grouted with cement slurry mixed with water proofing compound. (ii) 2nd layer of 25 mm thick cement mortar 1:3 (1 cement: 3 coarse sand) mixed with water proofing compound in recommended proportions. (iii) Finishing top with stone aggregate of 10 mm to 12 mm nominal size spreading @ 8 cudm/sqm thoroughly embedded in the 2nd layer. Using rough kota stone.

Providing and laying integral cement based treatment for water proofing on the vertical surface by fixing specified stone slab 22 mm to 25 mm thick with cement slurry mixed with water proofing compound conforming to IS:2645 in recommended proportions with a gap of 20 mm (minimum) between stone slabs and the receiving surfaces and filling the gaps with neat cement slurry mixed with water proofing compound and finishing the exterior of stone slab with cement mortar 1:3 (1 cement : 3 coarse sand) 20 mm thick with neat cement punning mixed with water proofing compound in recommended proportion complete at all levels and as directed by Engineer-in-charge : Using rough Kota stone

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of W.C., kitchen and the like consisting of: (i) Ist course of applying cement slurry @ 4.4 kg/sqm mixed with water proofing compound conforming to IS 2645 in recommended proportions including rounding off junction of vertical and horizontal surface. (ii) IInd course of 20 mm cement plaster 1:3 (1 cement : 3 coarse sand) mixed with water proofing compound in recommended proportion including rounding off junction of vertical and horizontal surface. (iii) IIIrd course of applying blown or residual bitumen applied hot at 1.7 kg. per sqm of area. (iv) IVth course of 400 micron thick PVC sheet. (Overlaps at joints of PVC sheet should be 100 mm wide and pasted to each other with bitumen @ 1.7 kg/sqm).

Providing and laying integral cement based water proofing treatment including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operations: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge over the RCC slab including adjoining walls upto 300 mm height including cleaning the surface before treatment. (b) Laying brick bats with mortar using broken bricks/brick bats 25 mm to 115 mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20 mm thick layer of cement mortar of mix 1:5 (1 cement :5 coarse sand ) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge to required slope and treating similarly the adjoining walls upto 300 mm height including rounding of junctions of walls and slabs. (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/ sqm of cement admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement :4 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineerin- charge including laying glass fibre cloth of approved quality in top layer of plaster and finally finishing the surface with trowel with neat cement slurry and making pattern of 300x300 mm square 3 mm deep. (e) The whole terrace so finished shall be flooded with water for a minimum period of two weeks for curing and for final test.“All above operations to be done in order and as directed and specified by the Engineer-in-Charge : With average thickness of 120 mm and minimum thickness at khurra as 65 mm.

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Providing and fixing in position pre-moulded joint filler in expansion joints.

Providing and laying in position bitumen hot sealing compound for expansion joints etc. Using grade ‘A’ sealing compound.

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge.

Taking out doors, windows and clerestory window shutters (steel or wood) including stacking within 50 metres lead : Of area 3 sq. metres and below

Dismantling steel work in built up sections in angles, tees, flats and channels including all gusset plates, bolts, nuts, cutting rivets, welding etc. including dismembering and stacking within 50 metres lead.

Extra for marking of structural steel work required to be re-erected.

Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50 metres lead. For thickness of tiles 10 mm to 25 mm

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved.

Supplying and stacking of good earth at site including royalty and carriage nupto 5 km complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage upto 5 km complete (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 mm

Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20% : one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Providing and displaying of Areca Palm having ht. 2.40 m to 2.70 m with 12 to 14 suckers, well developed, fresh and healthy with lush green foliage in 35 cm size of Bucket type cement pots & as per direction of the officer-in-charge.

Providing and Displaying plants Chrysenthemum single named variety in different colour well developed, having 45 to 60 cm ht., minimum 150 and above half bloom flowers well stacked with bamboo stick having three layer tiding by thread fresh and healthy foliage in 30 cm Earthen Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Salvia ht. 45 to 60 cm multi branches stacking with bamboo stick specimen plants type with full bloom well developed in 30 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Cockscomb well developed fresh & healthy 20 to 25 cm ht. attractive colours fully bloomed in 20 cm Earthen Pot/ Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying plants Sunflower single well developed 8 to 10 half bloom buds multi branched in fresh & healthy full stacked with green painted bamboo stick stacking in 25 cm Earthen Pot/Plastic Pot and as per direction of the officer-in-charge.

Providing and Displaying Topiary plant of Ficus Panda well developed with fresh & healthy foliage with 3 to 4 Ball and 60 to 75 cm spread each Ball, 135 to 150 cm ht., in 35 cm Cement Tray /Cement Pot as per direction of the officer-in-charge.

Supply and stacking of Azadirachta indica ( Neem ) plant of height 120- 130cm in big polybag of size 25 cm as per direction of the officer-in-charge.

Supply and stacking of Delonix regia (Gulmohar) plant of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge

Supply and stacking of Foxtail palm plant of ht. 240-270 cm bottom girth 35-40 cm well developed in big size HDPE bags as per direction of the officer-in-charge.

Supply and stacking of Mangifera indica (Mango-grafted ) plant of height 60-75 cm. in big poly bag of size 25 cm as per direction of the officer-incharge.

Supply and stacking of Plumeria alba plant of height 165-180 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.

Supply and stacking of Plumeria rubra plant of height 120-150 cm. with 3- 4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.

Supply and stacking of Polyalthia longifolia (Ashok) plant of height 150- 165 cm. in earthen pots of size 25 cm as per direction of the officer incharge.

Supply and stacking of plant Hibiscus rosasinensis of height 90-105 cm., bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and fixing Brand S.S. 316 Grade Mortice Handle Ø22mm with euro profile escutcheons [Finish : Satin] [Mechanically BSEN 1906 : 2010 Certified] AND Brand Lock Body - 9'' [With Stainless Steel main and strike plate] [Fire Rated – BSEN 1634 : 1 : 2000 Certified] complete as direction of Engineer-in-charge.

Providing and fixing Brand Pin Cylinder-60 mm [Key & Knob] [Fire Rated – BSEN 1634 : 1 : 2000 Certified] complete as direction of Engineer-in-charge.

Providing and fixing Brand Pin Cylinder-60 mm [Slot & Knob] [Fire Rated – BSEN 1634 : 1 : 2000 Certified] complete as direction of Engineer-in-charge.

Providing and fixing Brand S.S. (Normal Grade) Tower Bolt [Flate] 300 mm [Finish : Satin] complete as direction of Engineer-in-charge.

Providing and fixing Brand S.S.316 Grade Door Stop [Finish : Satin] complete as direction of Engineer-in-charge.

Excavation in Hilly Areas in Soil by mechanical means Excavation in soil in Hilly Area by mechanical means including cutting and trimming of side slopes and disposing of excavated earth with a lift upto 1.5 m and a lead upto 20 m as per Technical Specification Clause 1603.1

Excavation in Hilly Areas in Ordinary Rock by mechanical means not requiring blasting Excavation in hilly area in ordinary rock not requiring blasting by mechanical means including cutting and trimming of slopes and disposal of cut material with a lift upto 1.5 m and lead upto 20 m as per Clause 1603.2.

Excavation for Structures Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. Ordinary soil Upto 3 m depth

Concrete with cement, coarse sand and 40 mm gauge stone ballast in proportion 1:4:8 in foundations and floors including supply of all material, labour and T&P etc. required for proper completion of the work. as per drawings and technical specifications Clause 802, 803, 1202 & 1203

Supplying, fitting and placing HYSD bar reinforcement in foundation complete as per drawings and technical specifications Clauses 1000 and 1202

Supplying, fitting and placing HYSD bar reinforcement (Fe 415) in substructrue complete as per drawings and technical specification Clauses 1002, 1005, 1010 & 1202 (The reinforcement steel shall be procured from original (primary) steel producers as per clause no. 2011.3.1 of MORD specifications (First revision'2014) and IS 1786:2008 clause no. 1.6)

Providing concrete for plain/ reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 R.C.C. grade M 25

Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 (For height upto 5 m) R.C.C. grade M 25

Random Rubble Stone Masonry laid in 1:6 cement and sand mortar, in breast walls, retaining walls, parapets, scuppers, etc. including supply of all material, labour, T&P and royaltiies etc. complete as per drawing and technical specifications Clauses 702, 704, 1202 & 1203 of MORD Specifiction

Embankment Construction with Material Obtained from Borrow Pits (Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2)

Granular Sub-base with Well Graded Material (Table 400.1) By Mix in Place Method Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401. For Grading I Material

Cement Concrete (PCC M-30) Pavement:- Construction of Un-reinforced, Cement concrete pavement, thickness as per design, over a prepeared sub base with 43 grade cement or any other type PCC Grade M-30, coarse and fine aggregates conforming to IS: 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a concrete mixer of not less then 0.2 cum capacity and appropriate weigh batcher using approved mix design, laid in approved fixed side formwork (Steel channel, laying and fixing of wedges, steel plates including levelling the formwork and laying and fixing of 125 micron thick polythene film, as per drawing), spreading the concrete with shovels, rakes, compacted using needle, and plate vibrators, finished in continuous operation and curing of concrete slabs for 14 days, using curing compound where specified and water finishing to lines and grade as per drawings and technical specifications.

Providing and laying of hot applied thermoplastic compound of ISI Mark Approved Quality of 2.5 mm thick including reflectorising glass beads @ 250 gms per sqm area, as per IRC:35 .The finished surface to be level, uniform and free from streaks and holes

Road Studs / Cat Eye: Providing and fixing Bi-directional Road Studs (Cat Eye) / Reflective Pavement Marker (RPM) with single body twin shank and plastic body moulded from ASA (Acrylic Styrene Acrylonitrite) or HIPS (Hi-impact Polystyrene) or ABS (Acrylonitrile Butadiene Styrene) or any other suitable material approved by Engineer in charge (Marker must support a load of 13635 kg tested in accordance with ASTM D 4280 and Reflective lenses conforming to ASTM D 788 or equivalent) bonded or anchored within the road surface for lane marking and delineation for night time visibility as per Clause No. 1707 of MORD and 804 of MORTH specifications. The RPM must have reflective panels with micro prismatic lens where area of each retro reflective surface shall not be less than

Providing and Laying of Interlocking Concrete Block Pavements of M-40 Grade having thickness 80 mm as per drawings and Technical Specification Clause 1504.

Cast in Situ Cement Concrete M20 kerb (Construction of cement concrete kerb with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M-10 grade foundation 150 mm thick, foundation having 50 mm projection beyond kerb stone, kerb stone laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 408) Using Concrete Mixer

Retro-Reflective Traffic Signs with Type IV retro- reflective Sheet Providing and fixing of corrosion resistant 2mm thick Type IV retroreflective pcautionary, mandatory, informatory sign board with 7 year warranty as per IRC:67, made of high intensity sheeting fixed over ACP (Aluminium Composite Panel) 3 mm thick (including framing and bracing with fabrication, plotting, pasting, riveting, taping and nut, bolts, washers and rivets etc for fixing), supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing, issued in original by retro-reflective sheeting manufacturer having operations in India by their indian subsidary. (Clause No. 801 of MORTH) 900 mm equilateral triangle

600 mm equilateral triangle

600 mm Circular

Overhead Signs Providing and erecting overhead signs with a corrosion resistant 2mmthick Type IV HIP retro- reflective sheeting with 07 year warranty made of high intensity sheeting fixed over ACP (Aluminium Composite Panel) 4 mm thick (including framing and bracing with fabrication, plotting, pasting, riveting, taping and nut, bolts, washers and rivets etc for fixing), installed as per clause 802.7 over a designed support system of aluminium alloy or galvanised steel trestles and trusses of sections and type as per structural design requirements and approved plans issued in original by retro-reflective sheeting manufacturer having operations in India by their indian subsidary. (Clause No. 802 of MORTH) Truss and Vertical Support

Type IV HIP retro- reflective sheeting for Over Head Sign

Direction and Place Identification Signs upto 0.9 sqm Size Board. Providing and erecting direction and place identification sign with corrosion resistant 2mm thick Type IV retro- reflective cautionary, mandatory, informatory sign board with 7 year warranty as per IRC:67 made of high intensity sheeting fixed over ACP (Aluminium Composite Panel) 3 mm thick (including framing and bracing with fabrication, plotting, pasting, riveting, taping and nut, bolts, washers and rivets etc for fixing) with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing. (Clause No. 801 of MORTH)

Providing and Laying Reinforced Cement Concrete Pipe NP3 as per design in Single Row Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets Clause 1106. 0 Note:-The labour rate for 600 mm dia Hume pipe may be derived from the rates for 750 dia by decreasing 20 per cent 1000 mm dia

PLUMBING WORKS Providing & fixing stone slab table rubbed, edges rounded and polished of size 75 X 50cm deep and 1.8 cm thick fixed in urinal patitions by cutting chase of appropriate width with chase cutter and embedding the stone in chase with epoxy grout or with cement concrete 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregste 6mm nominal size) as per Engineer-in-charge and finished smooth White Agaria Marble Stone

Providing and fixing Salem Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with CI brackets and stainless steel waste with plug 40mm including painting of fittings and brackets, cutting and making good the walls wherever required. Kitchen sink with drain board 510X1040mm bowl depth 200mm.

Sink without drain board 610X510 mm bowl depth 200mm.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing: Rectangular shape 453x357 mm

Providing and fixing toilet paper holder: C.P. brass

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in-charge

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge..(sink & urinal)

Providing & fixing PTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealed fittings arrangement of approved quality and colour weighing not less than 88 gms

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality confirming to IS:8931 15mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore. 15 mm nominal bore

Providing and fixing wash bashin with C.I. brackets, 15mm dia cp brass singal hole basin mixer of approved quility and make, including painting of fittings and brackets, cutting and making good the walls wherever required - a) White vitreous china wash basin size 550x400 mm with a 15 mm cp brass singal hole basin mixer.

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having pre & post flushing with water ( 250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification and direction of Engineer-in-charge..

Providing & fixing PVC waste pipe for sink oncluding PVC waste fitting Complete Flexible Pipe 32mm Dia

Providing and fixing uplasticised PVC connection pipe with brass unions 45 cm length 15 mm nominal bore

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge . a) 15 mm nominal dia.

Providing and fixing CP Brass shower rose with 15 or 20 mm inlet 100 mm diameter

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms.

Supply, installation, testing and commissioning of AUTOMATIC soap dispenser holder with stainles steel lid and brackets fixed to wooden cleats with C.P. brass screws.

Supply, installation, testing and commissioning of ABS fully automatic "No Touch" hand drier suitable to operate on 220 volts, single phase 50 hz., A.C. power supply

Supply, installation, testing and commissioning of ABS fully automatic "No Touch" AUTOMATIC HAND SANITIZER suitable to operate on 220 volts, single phase 50 hz., A.C. power supply

Supply, installation, testing and commissioning of wall mounted 1 nos Stainless Steel Handicap DISABLED GRAB BAR (U SHAPE) - (SET OF 2)including cutting & making good the walls.

Supply, Installation, Testing and commissioning of wall hanging drinking online water cooler With cooling capacity of 60 LPH, with one drinking station and one swan neck tap for bottle filler , with MDCU29 Antimicrobial touch pad amd made by stainless steel top and heavy duty galvanized steel frame. With cooling capacity, ADA Compliant, size 472 mm Depth X 447mm width, flexible bubbler guard , Model- PG8AC ,operated between 50 to 120 PSI, Chiller unit Suitable to R134a Refrigerant, Adjustable thermostat control, suitable for 220-230v/50-60 hz A/C Supply Complete with all accessories which include MD-CU29, which is an EPA registered antimicrobial copper that fights off microorganisms which include MRSA and e-coli. The water Fountain shall possess NSF-USA, Green building, energy star saving certification, and to be placed at different location of buidling. for proper functioning and aesthetic view as directed by the engineer-in-charge without any extra cost. Certified By NSF, GRIHA, TUV, UL, WATER QUALITY Asso.,UL, Stare rating Energy saver. Mechanical operation .

Providing and fixing cast iron trap of self cleansing design with cast iron screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors. 100 mm inlet and 100 mm outlet Hubless centrifugally cast iron pipes epoxy coated inside & outside IS : 15905

100 mm inlet and 75 mm outlet Hubless centrifugally cast iron pipes epoxy coated inside & outside IS : 15905

Providing and fixing soil, waste, vent and rain water pipes 100mm dia , Hubless centrifugally cast iron pipes epoxy coated inside & outside IS : 15905

Providing and fixing bend of required degree with access door, insertion rubber washer 3mm thick, bolts and nuts complete. 100mm Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905

Providing and fixing plain bend of required degree. 100mm dia Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905

Providing and fixing double equal plain junction of required degree. Hubless centrifugally cast iron pipes epoxy coated inside & outside IS : 15905 100x100x100x100 mm

Providing and fixing single equal plain junction of required degree : Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905 100X100X100mm

Providing and fixing single unequal plain junction of required degree 100x 100x75 mm Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905

Providing and fixing Hubless cast iron offsets epoxy coated inside & outside as per IS : 15905 130 mm offsets With 100 mm dia

Providing and fixing terminal guard: 100mm Hubless centrifugally cast iron epoxy coated inside & outside IS : 15905

Providing and fixing shielded coupling for Hubless centrifugally cast iron pipe 100mm SS 304 grade coupling with EPDM rubber gasket

Providing and fixing PTMT grating of approved quality and colour Circular type 125 mm nominal dia

Providing and laying cement concrete 1:5:10 (1 cement: 5 coarse sand: 10 graded stone aggregate 40 mm nominal size) alround CI HUBLESS including bed concrete as per standard design, Note: This work shall be done all-round PIPE AT ground floor's toilet. 100mm diameter

Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. (internal work) 40 mm dia, nominal bore

50 mm dia, nominal bore

Providing & fixing on wall face unplasticised -Rigid PVC rain water pipes conforming to IS:13592 Tyape A included jointing with seal ring conforning to IS:5382 leaving 10 mm gap for thermal expansion. (i)Single socketed pipes. 110 mm diameter

Providing, fixing on wall face unplasticised - PVC moulded fittings /accessories for unplasticised - Rigid PVC rain water pipes conforming to IS ; 13592 Type A including jointing with seal ring conforming to IS ; 5382 leaving 10 mm gap for thermal expansion. Coupler -110 mm diameter

Bend -87.5 deg -110 mm diameter

Shoe -110mm shoe

Providing & fixing unplasticised - PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with .M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4(1cement : 4 coarse sand) and making good the wall etc. complete. 110 mm dia

Providing and fixing G.I. Inlet fitting of suitable size with 2 & 3 Nos. G.I. Socket 32 & 40 welded G.I. pipe and dipped in hot bitumen complete in all respect. 100 mm diameter pipe (Hopper )

Providing and fixing F.R.P. Grating. With "L" angal 366 x 1206(1001) x 40 mm ( Load Bearing capable 5.0 T, suitable for External drain Area )

Providing and fixing F.R.P. Grating. With "L" angal 526(525) x 1206(1001) x 40 mm ( Load Bearing capable 5.0 T, suitable for External drain Area )

Providing and fixing in position 25 mm diameter mosquito proof coupling of approved municipal design.

Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step CPVC solvent cement and testing of joints complete as per direction of engineer in charge. Internal work -Exposed on Wall 15 mm nominal outer dia pipes

20 mm nominal outer dia pipes

25 mm nominal outer dia pipes

32 mm nominal outer dia pipes

40 mm nominal outer dia pipes

50 mm nominal outer dia pipes

Providing and fixing CPVC pipes having thermal stability for hot and cold water supply including all CPVC plain and brass threaded fittings including fixing the pipe with clamps at 1.00 mt spacing. this includes jionting of pipes and fittings with one step CPVC solvent cement and the cost of cutting chases and making good the wall same including testing of joints complete as per the direction of engineer incharge concealed work including cutting chases and making good the wall etc. 15 mm nominal outer dia pipes

20 mm nominal outer dia pipes

Providing and fixing G.I. pipes complete with GI fittings and clamps including cutting and making good the walls etc. (internal work) For roof level 25 mm dia, nominal bore

32 mm dia, nominal bore

Providing and fixing of gun metal gate valve with CI wheel of approved quality (screwed ends) 25mm dia, nominal bore

40 mm dia, nominal bore

50 mm dia, nominal bore

Providing and fixing gun metal non- return valve of approved quality (PN 1.6) 40 nominal bore

50 nominal bore

80 nominal bore

Providing and fixing brass stop cock of approved quality 15mm nominal bore

20mm nominal bore

Structual steel work welded in built up sections, trusses and framed work including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

BUTTERFLY VALVE (MANUAL) with C I body SS Disc, Nitrile Rubber Seal & O- Ring PN 16 pressure rating for chilled water/hot eater circulation as specified 65 nominal bore

80 nominal bore

100 nominal bore

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class “O”) insulation on gyeser and solar water pipe suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required. 19mm

Providing and fixing GI pipes medium class conferming to IS 1239 with GI fittings including cutting hole chase painted with primer, two coats of enamel paints etc 100 mm dia, NB

Providing and fixing brass ball valve with SS 304 Stem and ball, teflon seat complete (PN-16). 15 mm dia nominal bore

20 mm dia nominal bore

25 mm dia nominal bore

Providing, fixing, testing and commissioning of motorised butterfly valve of following dia for filling of overhead water tank complete with high and low level control switches to control tanks. The level controllers shall be installed in iverhead tanks. The level switch will close the valve when water level is high in overhead tank and open the valve when overhead water tank level is low. The system should be complete in all respects with accessories 220 V AC / 2 V DC, IP67 electrical water level control unit, copper control wiring in whether proof casing etc. 50 mm dia NB Float Valve

System Capacity : 2500 liters ( storage tank of 2500 litres ) per day (LPD) having 25 collectors. - Nurse Hostel

System Capacity : 1400 liters ( storage tank of 1400 litres ) per day (LPD) having 14 collectors. - Jr.& Sr Resident and Boys & Girls inter Hostel

System Capacity : 600 liters ( storage tank of 600 litres ) per day (LPD) having 6 collectors with Eelectrical element. Type III

HOT WATER AND RO WATER SUPPLY PIPE Providing and fixing Stainless Steel pipes confirming to 316L EN 10312 Material No.1.4401(X5 CrNiMo 17-12-2) with 2.3% Mo (S.S.Grade-316L) ,complete with Press Type fittings Material No.1.4408 suitable for doubley secure pressing (two pressings simultaneously– one in front of the crimp and one behind it) for torsion proof and longtitudinally forcelocked connection.with Black; EPDM Sealing Element with SC-Contur in accordance with DVGW regulation W534, DW 8501 BL 0551, DW 8511 BQ 0245) for RO water supply capable to withstand temprature up to 110 degree centrigrade and working pressure 16 bar, such as sockets, bends, elbows, tees, reducers, unions, Flanges etc. necessary adapters for GI/Copper and CP fittings.Clamps with hanger at a spacing as required, jointing, sundries, cutting holes in walls/floors/slabs & making good complete. 15 mm nominal outer dia pipes

22 mm nominal outer dia pipes

28 mm nominal outer dia pipes

35 mm nominal outer dia pipes

42 mm nominal outer dia pipes

54 mm nominal outer dia pipes

76.1 mm nominal outer dia pipes

88.9 mm nominal outer dia pipes

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All kinds of soil up to 1.50 m depth Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia

Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5 m, but not exceeding 3 m. (Rate is over corresponding basic item for depth upto 1.5 metre).

Providing laying and jointing glazed stoneware pipes grade ‘A’ with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete. 150 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) alround SW pipes including bed concrete as per standard design. 150 mm diameter

Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. (for storm drainage) 250 mm dia RCC pipe

300 mm dia RCC pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 250 mm dia RCC pipe

300 mm dia RCC pipe

Constructing brick masonry manhole with F.P.S. bricks in cement mortar 1 : 4 (1 cement : 4 coarse sand) RCC top slab with 1 : 2 : 4 mix (1 cement : 2 coarse sand : 4 grade stone aggregate 20mm nominal size); foundation concrete 1:4:8 mix (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size) inside plastering 12 mm thick with cement mortar 1:3 (1cement 3 coarse sand ) finished with a floating coat of neat cement and making channels in cement concrete 1:2:4 (1cement : 2 coarse sand: 4 graded stone aggregate 20 mm nominal size) finishd with a floating coat of neat cement complete as per standard design Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Inside size 120x90 cm and 90 cm deep including C.I. cover with frame (medium duty) 500 mm internal diameter, total weight of cover and frame to be not less than 116 kg (weight of cover 58 kg and weight of frame 58 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manhole with F.P.S. bricks size 90 X 80 cm : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manhole with F.P.S. bricks Size 120x90 cm; With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS : 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Providing and fixing square mouth SW gully trap grade ‘A’ complete CI grating brick masonry chamber with bricks of class designation 75 and water tight CI cover with frame of 300 x 300 mm size (inside) the weight of cover to be not less than 13.00 kg and frame to be not less than 5 kg. as per standard design. (COVER MIN. 4.5 KG & FRAME MIN.2.7 KG ) 180x150 mm size P type With FPS bricks

Making connection of drain or sewer line with existing manhole including breaking into and making good the walls, floors with cement cincrete 1:2:4 mix (1cement: 2 coarse sand : 4 graded stone aggregate 20mm nominal size) cement plastered on both sides with cement mortar 1:3 (1cement : 3 coarse sand) finished with a floating coat of neat cement and making necessary channels for the drain etc. complete for pipes 100 to 230mm dia.

Providing and laying non-pressure NP2 class (light duty) RCC pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete. (for storm drainage) 150 mm dia RCC pipe

450 mm dia RCC pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 150 mm dia RCC pipe

Constructing brick masonry road gully chamber 50x45x60 cm with bricks of class designation 75 in cement mortar 1:5 (1 cement : 5 fine sand) including 500 x 450 mm (heavy duty) precast RCC horizontal grating with frame complete as per standard design: with FPS bricks

Earth work in excavation in ordinary soil in all of foundation trenches including dressing of the side and ramming of bottom. Lifts upto 1.5m including getting out the excavated soil and disposal of surplus excavated soil a directed within a lead of 50m All kinds of soil.

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Providing and laying in position cement concrete of specied grade excluding the cost of centering and shuttering (for filling of drain haunches) by 1:2:4 (1 cement : 2 coarse sand : 4 graded stone agg. 20 mm nominal size)

Providing and laying damp-proof course 40mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 12.5mm nominal size).

12 mm cement plaster of mix 1:6 (1 cement : 6 coarse sand).

Reinforced cement concrete work in RCC culvert slab with 1:1.5:3 (1 cement : 1.5 coarse sand and 3 gradded stone aggregate of 20 mm nominal size) excluding centering and shuttering and reinforcement. (Rate 5494.55+(5735.75-5344.80)=5885.50

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level. Thermo Mechanically Treated bars.

Brick work with F.P.S. bricks of class designation 75 in foundation and plinth in: Cement mortar 1:4 (1 cement: 4 coarse sand)

Centring and shuttering including strutting, proppintg etc. and removal of form for: Edges of slabs and breaks in floors and walls, Under 20 cm wide

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality L D- 2.5 Rectangular shape 600x450mm internal dimensions

Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to window frames etc. including 62x19 mm beading of second class teak wood and priming coat with approved steel primer all complete.

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS:2800(Part I ), including collecting sample from different strata , preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90m depth below ground level.Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS:2800(Part I ), including collecting sample from different strata , preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90m depth below ground level. All types of Soil 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of Engineer-in-charge. 150mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized plc. medium well screen(RMS) pipes with ribs, conforming to IS: 12818, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per director of Engineer-in-charge. 150 mm nominal size dia

Supplying, filling, spreading & levelling stone boulders of size range 5cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & levelling gravel of size range 5mm to 10mm, in recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & levelling coarse sand of size range 1.5mm to 2mm, in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tube well as per IS:2800 (part I). 100 mm dia

Providing and fixing G.I. pipes complete with G.I. fittings including ,trenching and refilling etc. external works 25mm nominal bore

50mm nominal bore

65mm nominal bore

80mm nominal bore

Painting GI pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality 25 mm dia, nominal bore

50 mm dia, nominal bore

65 mm dia, nominal bore

80mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : external works 65mm nominal bore

80mm nominal bore

Providing and filling sand of grading zone V or coarser grade all-round the G.I. pipes in external work. 25mm nominal bore

50mm nominal bore

65mm nominal bore

80mm nominal bore

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : 50 mm dia

80 mm dia

100 mm dia

Providing & Fixing C.I.sluice valve(with cap) complete with bolts,nuts,rubber insertions etc.(the tail pieces if required will be paid separately) 100 mm dia.pipe

150 mm dia.pipe

Constructing masonry chamber 30x30x50 cm,inside with 75 class designation brick work in cement mortar 1:4 (1 cement:4 coarce sand) for stop cock complete with C.I. surface box 100x100x75mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 corase sand: 4 graded stonr aggregate 20mm nominal size) necessary excavation foundation concret 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortor 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design.

Constructing masonry Chamber 60X60X75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement: 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with channel lid and RCC top slab 1:2:4 mix (1 cement: 2 coarse sand: 4 graded stone sggregate 20 mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand: 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement: 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design: With F.P.S. bricks

Excavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 M including getting out the excavated soil (HARD OR SOFT) and then returning the soil as required in layers not exceeding 20 cms in depth including consolidating each deposited layer by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50m. [hard/Dense soil] All kind of soil Extra for excavating trenches for pipes, cables etc. in all kinds of soil for depth exceeding 1.5m,but not exceeding 3 m.(Rate is over corresponding basic item for depth up to 1.5 metre).

Making connection of GI distribution branch with GI main of 50-80mm nominal bore by providing and fixing tee, including cutting and threading the pipe etc. complete.

Providing & fixing of Garden hydrant outlet consisting 1 No. 20mm dia. Ball valve, Bib cock (Brass) for connecting rubber hose, pipes & fittings including brick masonary chamber 300x300x500mm. Bib Cock - 20mm

Ball Valve - 20mm

BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. NON - RETURN VALVE with dual plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating as specified. 100 nominal bore

80 nominal bore

Providing and fixing GI pipes medium class conferming to IS 1239 with GI fittings including cutting hole chase painted with primer, two coats of enamel paints etc 150 mm dia, NB

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6 mm thick hard board backing: Rectangular shape 453x357 mm

Providing & fixing chrome plated brass battery based infrared sensor operated pillar cock, having foam flow technology.

Providing and fixing MS holder bat clamps of approved design to cast iron (spun) pipe embedded in and Including cement concrete blocks 10 x10 x10cm of 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) including cost of cutting holes and making good the walls etc. For 100mm dia. Pipe

(Pumps, ETP, STP, Electromechanical) WORKS Raw Water Treatment Feed Pump set Providing, fixing, commissioing and testing package vertical raw water pumps, comprising of Electrical Driven inline pumping with all accessories, Pumps shall be with C.I. Base, S.S 304, impeller, shaft, mechanical seal, S.S. Shaft directly coupled to motor suitable for operation on 400/440 volts, 3 phase 2900 RPM. TEFC electronic motor mounted on a common channel baseplate 150mm dia pressure gauge, GM isolation cock and cement concrete foundation with plaster with dunlop cushy foot mountings with all accessories such as NRVs, valves, pressure guage bourden type, common suction and delivery header, bellows on sucton and delivery side complete in all repsects. Pumps shall be suitable for 415 ± 10% volts 3 phase 50 Hz A.C supply & shall be having the following requirement complete with foundation and associated civil works. Suction & Delivery Header - SS 304 Control Valve On suction and Delivery - Ball Valve Only (No Butterfly Valve Accepted). Flow Prevention - Only Check Valve Suction & delivery header including all pipes, suction & delivery sides valves, NRV, Pressure gauges & accessories complete. Flow Rate : 9.0 LPS (1 working + 1 stand by) Head : 35 M Min. Motor HP : 8.5 H.P. (Each)

Water Booster Pumpset (Treated Water Supply) Supplying & supervision of testing & commissioning of Booster Pumpset (Hydropneumatic systems) as described below Supplying & supervision of testing & commissioning of package vertical Hydropneumatic system, comprising of 2.0 nos. (1 duty + 1 stand by) Electrical Driven inline pumping sets each of 9.0 LPS to a head to 60 meter with all accessories, Pumps shall be with C.I. Base, S.S 304, impeller, shaft, mechanical seal, S.S. Shaft directly coupled to motor suitable for operation on 400/440 volts, 3 phase 2900 RPM. TEFC electronic motor mounted on a common channel baseplate 150mm dia pressure gauge, GM isolation cock and cement concrete foundation with plaster with dunlop cushy foot mountings with all accessories such as NRVs, valves, pressure switch, common suction and delivery header, bellows on sucton and delivery side complete in all repsects. Pump mounted or wall mounted microprocessor based controller, Electronic control panel with frequency inverter, logic controller relays, pressure sensor, pressure sensor transmitter, electrical wiring, cabling from panel to pumps, level controller, two lined LCD display, diodes to indicate pump ready, pump running and fault capable to communicate with toher RS 485 interface. with Power box equipped with fuses or isolators or circuit breakers as required. complete with all accessories as per manufacturer specifications. Suction & Delivery Header - SS 304 Control Valve On suction and Delivery - Ball Valve Only (No Butterfly Valve Accepted). Flow Prevention - Only Check Valve One Number Variable frequency Drive Impeller : Stainless Steel Shaft : Stainless Steel RPM : 2900. Mover : Electric Motor HP - As required. Necessary foundation with bolts NRV on delivery Dust & vermin proof cubicle type motor control centre fabricated from powder coated 16 SWG MS sheet suitable to automatic working of above mentioned pumps. Ball valve on suction & delivery

Sump Pumps Supply & Installation, testing and commissioning of centrifugal non clogging submersible sump pumps for plant room drainage. Pump capable capable of handling 25 mm dia soft solids. Motor suitable for 415 + 10% volts, 3 phase, 50 Hz AC Power supply. Pumps shall be suitable for automatic/manual operation (Overall depth of sump – 1.5 M). Submersible sump pump shall be provided with dry running protection. Inclusive of supporting arrangement for stationary type. Two nos. of pump installed in one sump pit 1 working & 1 standby with automatic/manual opration as requireds. Waste Water Drainage Sump Pump (PLANT ROOM ) Flow rate : 4.0 LPS Head : 10 Mtrs. Min. Motor HP : 2.0 (Each)

Supplying, storing, handling, installation, testing & commissioning of Vertical Dual Media Filter made out of MSEP/FRP composite Vessel complete suitable for test pressure of 7 Kg./cm2 with top and bottom dished ends, self supporting legs, manhole, hand hole, initial filling of Graded sand and gravels, pressure gauges, sampling cock, air vent, frontal MS/UPVC Piping, diaphragam valves for inlet, outlet, backwash inlet, backwash outlet drain etc. Capacity : 9.0 LPS Working Pressure : (5 ± 2.5)MWC

Supplying, storing, handling, installation, testing & commissioning of Vertical Activated Carbon Filter made out of MSEP/FRP composite Vessel complete suitable for test pressure of 7 Kg./cm2 with top and bottom dished ends, self supporting legs, manhole, hand hole initial filling of Activated Carbon, pressure gauges, sampling cock, air vent, frontal MS/UPVC piping, diapharagam valves for intlet, outlet, backwash inlet, backwash outlet drain etc. Capacity : 9.0 LPS Working Pressure : (5 ± 2.5)MWC

Supplying, storing, handling, installation, testing & commissioning of water softening system having MSEP/FRP pressure vessel suitable for test pressure of 7 Kg/cm2 including dished end, ion- exchange resin, Frontal piping, C.I. diaphragm type valve, brine injection assembly for regeneration of softener, brine measuring cum salt water tank, inter connected flexible polypropylene MS Rubber lined (MSRL) piping, valves including provision of bye-pass arrangement complete with inside and outside painting etc. as required. Receiving, storing, handling and fixing of PVC/HDPE/FRP tank for Brine solution along with Hydraulic Injector with control valve and piping for brine injection. Capacity : 9.0 LPS Working Pressure : (5 ± 2.5)MWC

Supplying and fixing of PVC/HDPE/FRP tank including electrical operated metering/dosing pump for dosing of alum/sodium hypo-chlorite solutions in pipeline (all contacting parts shall be of stainless steel). Capacity - 0-12 LPH

Supplying & fixing of float based visual flow meter (Rotameter) suitable for water flow rate of 32400 litres per hour in the input line of water softener including matching flanges, nuts, bolts and 3 mm thick rubber insertions/gaskets complete. to assess the water flow rate in water softener.

RO PLANT - For Academic Block Lab Area Supplying, installing, testing & commissioning of R.O. Plant including filters, pumps, dosing units, control panel, piping and valves and 1,000 litres SS 304 stainless steel tank complete as per specifcation and drawings. For Drinking Feed Flow - 1000 LPH Product Flow - 500 LPH Reject Flow - 500 LPH Recovery - 50% Mode of operation - Manual Operating Pressure - 10 to 12 Kg/cm2

POWER & CONTROL CABLING Supplying and Earthing with GI earth plate 600mm x 600 mm x 6mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc, with coke and salt ) as required.

Supplying and laying 25 mm x 5 mm. G.I. strip in 40 mm dia. G.I. Pipe from earth electrode, as required.

Providing & fixing 25mm x 5mm G.I. strip on surface or in recess for connections etc. as required.

Providing and Fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing alongwith existing surface/ recessed conduit/ submain wiring/ cable as required.

Supplying, fabricating and installing following size of perforated M.S. cable trays, including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M.S. suspenders and including paint 100 mm width X 50 mm depth X 1.6 mm thickness

300 mm width X 50 mm depth X 1.6 mm thickness

Laying and fixing of One number PVC Insulated and PVC Sheathed/XLPE power cable of 1.1 kV grade of size not exceeding 25 sqmm on surface as required.

Laying and fixing of One number PVC Insulated and PVC Sheathed/XLPE power cable of 1.1 kV grade of size exceeding 25 sqmm but not exceeding 120 sqmm on surface as required.

Supplying of all materials and making terminations of 1.1 KV grade aluminium multicore cables of the following sizes. The work includes cable glanding using brass plated double compression glands, sizing the core leads, removing insulation, fixing suitable crimping type copper lugs/ thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting the same to the equipment terminals. 3.5 Core 120 sq. mm. Armoured Aluminium cable.

3.5 Core 35 sq. mm. Armoured Aluminium cable.

Control Cabling ( PVC insulated and PVC sheathed, armoured, Copper Conductor of 1.1 KV grade on existing cable trays). 5C x 1.5 Sq. mm

Supplying, installation, testing & commissioning of Sewage Treatment Plant for the following duty: Nature of waste water - Sewage + effluent Daily average flow - 140 + 25 cum/day Influent Characteristics pH - 8 BOD5 - 250- 300 mg/liter S. Solids - 250 mg/liter COD - 400-600 mg/liter Oil & Grease ` - <50 mg/liter Effluent discharge standard : pH - 6.5-8.0 BOD5 - Less than 10 mg/liter & < 5 after GRA-UOT S. Solids - Less than 10 mg/liter COD - Less than 50 mg/liter Oil & Grease - < 5 mg/lt Reuse of STP treated water after treatment. Horticulture, Landscaping, irrigation, flushing etc. NOTE (1) All Civil works finished with water proofing, plaster, snowcem, structure duly tested for leak-proofing, plant room flooring etc and related S.S/MS/CI works such as supply and fixing of handrails, manholes, gratings, grills, doors, vents, footrests etc shall be in the scope of the STP Client. Supply and fixing of puddle flanges will in the scope of Civil Contractor/ Client. (2) Contractor shall ensure submission of detailed GA drawings (Plan & Section), P & I diagram, schematic diagram for the above mentioned components and additional components such as inserts, puddle flanges, vent pipes etc. if so required for the complete automatic working of the STP and have it approved by the Owner / Consultants. Part (A) ETP Supply, installation, testing & commissioning of Screens 2 Nos.Mild Steel Suitable Sized Manually operated Bar Screen made of MS in RCC screen channel as per following specifications Cleaning :- Manual Screen MOC :- Complete in MS

Supply, installation, testing & commissioning of Raw sewage Transfer pumps with suitable solid handling capacity with CI casing & CI impeller complete with all accessories, motor of required capacity. The pumps shall be complete with Delivery header with, pressure gauge on delivery line with isolation level controller (with wiring) to control the level of Sump automatically. Pumps shall have following duty: Pumps = 02 Nos.(1w + 1s) Flow rate (each) = 4.5 m³/hr Head = 8-10 m

Dosing System for Physico-chemical treatment Alum dosing system Lime dosing system Poly dosing system

Supply, installation, testing & commissioning of Sludge recirculation/transfer pumps for sludge Feeding to filter press complete with all the accessories, motor of required capacity. The pumps shall be complete with Base frame, Delivery header with pressure gauge on delivery line . Pumps = 02 Nos.(1w + 1s) Flow rate (each) = 1 m³/hr Head = 8-10 m

STP Supply, installation, testing & commissioning of Screens 2 Nos.Mild Steel Suitable Sized Manually operated Bar Screen made of MS in RCC screen channel as per following specifications Cleaning :- Manual Screen MOC :- Complete in MS

Supply, installation, testing & commissioning of Submersible pumps with solid handling capacity upto 30 - 40 mm with CI casing & CI impeller complete with all accessories, motor of required capacity. The pumps shall be complete with Delivery header with, pressure gauge on delivery line with isolation level controller (with wiring) to control the level of Sump automatically. Pumps shall have following duty: Pumps = 02 Nos.(1w +1s) Flow rate (each) = 5.5 m³/hr Head = 8-10 m

Providing and fixing all interconnecting exposed plant piping of required MOC as MS/GI/PVC/CPVC/UPVC and isolation control valves for making the piping arrangement complete within the battery limits.

Supply, installation, testing & commissioning of SBR Based Biological system comprising of the following equipments: Air Blowers For SBR tanks Capacity : 100-250 m3/hr @ 5000-5500 mmwg Type Twin Lobe Qty -2 Nos. (1 w+1s) Disc type Fine Bubble Diffusers Size: 300 mm DiaDecanter system Qty -1 Nos. Type : Moving/Floating MOC : SS-304 Pipes and fittings for Air piping and Air Grid Qty-1 Lot Level transmitter/controller and accessories Qty-1 Lot PLC for SBR system Qty -1 Set

Supplying, installing, testing, commissioning of Centrifugal Horizontal Filter Feed pumps Complete in CI body& CI impeller with motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, strainer at suction. The pump shall be suitable for 415±10% volts 3 phase AC supply . Pumps = 02 Nos.(1w + 1s) Flow rate (each) = 5.5 m³/hr Head = 25 - 30 m

Supply, installation, testing & commissioning of Sludge recirculation/transfer pumps for sludge Feeding to filter press complete with all the accessories, motor of required capacity. The pumps shall be complete with Base frame, Delivery header with pressure gauge on delivery line . Pumps = 02 Nos.(1w + 1s) Flow rate (each) = 1-2 m³/hr Head = 8-10 m

Supply, installation, testing & commissioning of Sludge feed pumps for sludge Feeding to sludge bag system complete with all the accessories, motor of required capacity. The pumps shall be complete with Base frame, Delivery header with pressure gauge on delivery line . Pumps = 02 Nos.(1w + 1s) Flow rate (each) = 0.5-1 m³/hr Head = 25-30 m

Supplying, Installation, testing and commissioning of Chemical dosing system compromising of Sintex Tank with inlet/ outlet connection, piping and valves alongwith metering pump for dosing.

Supplying, installing, testing, commissioning of Filter Press of suitable size for the dewatering of sludge generated per day.

Supplying, installation, testing & commissioning of MSEP/FRP vessel filter with frontal piping and Valves with all the required accessories. Filter shall include media, standard fittings like pressure gauges, sampling cock, rinse drain. Multigrade Sand Filter Dia : 1100 mm HOS: 1800 mm Filter media: Fine and coarse sand, pebbles and gravels

Activated Carbon Filter Dia : 1100 mm HOS: 1800 mm Filter media: Activated Carbon, fine and coarse sand, pebbles and gravels

Water Booster Pumpset (Flushing / Soft Water Supply) Supplying & supervision of testing & commissioning of Booster Pumpset (Hydropneumatic systems) as described below Supplying & supervision of testing & commissioning of package vertical Hydropneumatic system, comprising of 2.0 nos. (1 duty + 1 stand by) Electrical Driven inline pumping sets each of 4.0 LPS to a head to 60 meter with all accessories, Pumps shall be with C.I. Base, S.S 304, impeller, shaft, mechanical seal, S.S. Shaft directly coupled to motor suitable for operation on 400/440 volts, 3 phase 2900 RPM. TEFC electronic motor mounted on a common channel baseplate 150mm dia pressure gauge, GM isolation cock and cement concrete foundation with plaster with dunlop cushy foot mountings with all accessories such as NRVs, valves, pressure switch, common suction and delivery header, bellows on sucton and delivery side complete in all repsects. sensor transmitter, electrical wiring, cabling from panel to pumps, level controller, two lined LCD display, diodes to indicate pump ready, pump running and fault capable to communicate with toher RS 485 interface. with Power box equipped with fuses or isolators or circuit breakers as required. complete with all accessories as per manufacturer specifications. Suction & Delivery Header - SS 304 Control Valve On suction and Delivery - Ball Valve Only (No Butterfly Valve Accepted). Flow Prevention - Only Check Valve One Number Variable frequency Drive Impeller : Stainless Steel Shaft : Stainless Steel RPM : 2900. Mover : Electric Motor HP - As required. Necessary foundation with bolts Ball valve on suction & delivery NRV on delivery Dust & vermin proof cubicle type motor control centre fabricated from powder coated 16 SWG MS sheet suitable to automatic working of above mentioned pumps.

Providing, fixing, testing and commissioning of horizontal centrifugal Irrigation water transfer pumps. The pumps shall be made of C.I. casing, CI impeller, SS shaft & sleeve. Mechanical seal connected by to a TEFC induction motor mounted on a common channel base-plate with efficiency class IE3 or EFF-1 whichever is more efficient with coupling guard 150 mm dia pressure gauge with GM isolation cock, suitable vibration eliminator, pads of approved design. Motor to be suitable for 400/440V, 3 phase 50 cycles AC power supply, including all necessary piping, suction and delivery header, individual suction and delivery of pump, valves, NRV, pressure gauge and other accessories and concrete foundation complete as required. Irrigation pumps: Capacity : 5 LPS Head : 50 Mtrs Type of Pump : Horizonal Centrifugal pump No. of Pumps (2 Nos. – 1 W + 1 S) Pump mounted or wall mounted microprocessor based controller, Electronic control panel with frequency inverter, logic controller relays, pressure sensor, pressure

Raw Water Treatment Feed Pump set Providing, fixing, commissioing and testing package vertical raw water pumps, comprising of Electrical Driven inline pumping with all accessories, Pumps shall be with C.I. Base, S.S 304, impeller, shaft, mechanical seal, S.S. Shaft directly coupled to motor suitable for operation on 400/440 volts, 3 phase 2900 RPM. TEFC electronic motor mounted on a common channel baseplate 150mm dia pressure gauge, GM isolation cock and cement concrete foundation with plaster with dunlop cushy foot mountings with all accessories such as NRVs, valves, pressure guage bourden type, common suction and delivery header, bellows on sucton and delivery side complete in all repsects. Pumps shall be suitable for 415 ± 10% volts 3 phase 50 Hz A.C supply & shall be having the following requirement complete with foundation and associated civil works. Suction & Delivery Header - SS 304 Control Valve On suction and Delivery - Ball Valve Only (No Butterfly Valve Accepted). Flow Prevention - Only Check Valve Suction & delivery header including all pipes, suction & delivery sides valves, NRV, Pressure gauges & accessories complete. Flow Rate : 9.5 LPS (1 working + 1 stand by) Head : 35 M Min. Motor HP : 9.0 H.P. (Each)

Water Booster Pumpset (Treated Water Supply) Supplying & supervision of testing & commissioning of Booster Pumpset (Hydropneumatic systems) as described below Supplying & supervision of testing & commissioning of package vertical Hydropneumatic system, comprising of 2.0 nos. (1 duty + 1 stand by) Electrical Driven inline pumping sets each of 9.5 LPS to a head to 60 meter with all accessories, Pumps shall be with C.I. Base, S.S 304, impeller, shaft, mechanical seal, S.S. Shaft directly coupled to motor suitable for operation on 400/440 volts, 3 phase 2900 RPM. TEFC electronic motor mounted on a common channel baseplate 150mm dia pressure gauge, GM isolation cock and cement concrete foundation with plaster with dunlop cushy foot mountings with all accessories such as NRVs, valves, pressure switch, common suction and delivery header, bellows on sucton and delivery side complete in all repsects. Pump mounted or wall mounted microprocessor based controller, Electronic control panel with frequency inverter, logic controller relays, pressure sensor, pressure sensor transmitter, electrical wiring, cabling from panel to pumps, level controller, two lined LCD display, diodes to indicate pump ready, pump running and fault capable to communicate with toher RS 485 interface. with Power box equipped with fuses or isolators or circuit breakers as required. complete with all accessories as per manufacturer specifications. Suction & Delivery Header - SS 304 Control Valve On suction and Delivery - Ball Valve Only (No Butterfly Valve Accepted). Flow Prevention - Only Check Valve One Number Variable frequency Drive Impeller : Stainless Steel Shaft : Stainless Steel RPM : 2900. Mover : Electric Motor HP - As required. Necessary foundation with bolts Ball valve on suction & delivery NRV on delivery Dust & vermin proof cubicle type motor control centre fabricated from powder coated 16 SWG MS sheet suitable to automatic working of above mentioned pumps.

Sump Pumps Supply & Installation, testing and commissioning of centrifugal non clogging submersible sump pumps for plant room drainage. Pump capable capable of handling 25 mm dia soft solids. Motor suitable for 415 + 10% volts, 3 phase, 50 Hz AC Power supply. Pumps shall be suitable for automatic/manual operation (Overall depth of sump – 1.5 M). Submersible sump pump shall be provided with dry running protection. Inclusive of supporting arrangement for stationary type. Two nos. of pump installed in one sump pit 1 working & 1 standby with automatic/manual opration as requireds. Waste Water Drainage Sump Pump (PLANT ROOM ) Flow rate : 4.0 LPS Head : 10 Mtrs. Min. Motor HP : 1.5 (Each)

Supplying, storing, handling, installation, testing & commissioning of Vertical Activated Carbon Filter made out of MSEP/FRP composite Vessel complete suitable for test pressure of 7 Kg./cm2 with top and bottom dished ends, self supporting legs, manhole, hand hole initial filling of Activated Carbon, pressure gauges, sampling cock, air vent, frontal MS/UPVC piping, diapharagam valves for intlet, outlet, backwash inlet, backwash outlet drain etc. Capacity : 9.5 LPS Working Pressure : (5 ± 2.5)MWC

Supplying, storing, handling, installation, testing & commissioning of water softening system having MSEP/FRP pressure vessel suitable for test pressure of 7 Kg/cm2 including dished end, ion- exchange resin, Frontal piping, C.I. diaphragm type valve, brine injection assembly for regeneration of softener, brine measuring cum salt water tank, inter connected flexible polypropylene MS Rubber lined (MSRL) piping, valves including provision of bye-pass arrangement complete with inside and outside painting etc. as required. Receiving, storing, handling and fixing of PVC/HDPE/FRP tank for Brine solution along with Hydraulic Injector with control valve and piping for brine injection. Capacity : 9.5 LPS Working Pressure : (5 ± 2.5)MWC

Supplying & fixing of float based visual flow meter (Rotameter) suitable for water flow rate of 18000 litres per hour in the input line of water softener including matching flanges, nuts, bolts and 3 mm thick rubber insertions/gaskets complete. to assess the water flow rate in water softener.

RO PLANT - For Academic Block Lab Area Supplying, installing, testing & commissioning of R.O. Plant including filters, pumps, dosing units, control panel, piping and valves and 1,000 litres SS 304 stainless steel tank complete as per specifcation and drawings. For Drinking Feed Flow - 1000 LPH Product Flow - 500 LPH Reject Flow - 500 LPH Recovery - 50% Mode of operation - Manual Operating Pressure - 10 to 12 Kg/cm2

POWER & CONTROL CABLING Supplying, fabricating and installing following size of perforated M.S. cable trays, including horizontal and vertical bends, reducers, tees, cross members and other accessories as required and duly suspended from the ceiling with M.S. suspenders and including paint Supplying of all materials and making terminations of 1.1 KV grade aluminium multicore cables of the following sizes. The work includes cable glanding using brass plated double compression glands, sizing the core leads, removing insulation, fixing suitable crimping type copper lugs/ thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting the same to the equipment terminals. Control Cabling ( PVC insulated and PVC sheathed, armoured, Copper Conductor of 1.1 KV grade on existing cable trays). 5C x 1.5 Sq. mm

Supplying, installation, testing & commissioning of Sewage Treatment Plant for the following duty: Nature of waste water - Sewage + effluent Daily average flow - 240 + 10 cum/day Influent Characteristics pH - 8 BOD5 - 250- 300 mg/liter S. Solids - 250 mg/liter COD - 400-600 mg/liter Oil & Grease ` - <50 mg/liter Effluent discharge standard : pH - 6.5-8.0 BOD5 - Less than 10 mg/liter & < 5 after GRA-UOT S. Solids - Less than 10 mg/liter COD - Less than 50 mg/liter Oil & Grease - < 5 mg/lt Reuse of STP treated water after treatment. Horticulture, Landscaping, irrigation, flushing etc. NOTE (1) All Civil works finished with water proofing, plaster, snowcem, structure duly tested for leak-proofing, plant room flooring etc and related S.S/MS/CI works such as supply and fixing of handrails, manholes, gratings, grills, doors, vents, footrests etc shall be in the scope of the STP Client. Supply and fixing of puddle flanges will in the scope of Civil Contractor/ Client. (2) Contractor shall ensure submission of detailed GA drawings (Plan & Section), P & I diagram, schematic diagram for the above mentioned components and additional components such as inserts, puddle flanges, vent pipes etc. if so required for the complete automatic working of the STP and have it approved by the Owner / Consultants. Part (A) ETP Supply, installation, testing & commissioning of Screens 2 Nos.Mild Steel Suitable Sized Manually operated Bar Screen made of MS in RCC screen channel as per following specifications Cleaning :- Manual Screen MOC :- Complete in MS

Supply, installation, testing & commissioning of Raw sewage Transfer pumps with suitable solid handling capacity with CI casing & CI impeller complete with all accessories, motor of required capacity. The pumps shall be complete with Delivery header with, pressure gauge on delivery line with isolation level controller (with wiring) to control the level of Sump automatically. Pumps shall have following duty: Pumps = 02 Nos.(1w + 1s) Flow rate (each) = 4.0 m³/hr Head = 8-10 m

Supply, installation, testing & commissioning of Sludge recirculation/transfer pumps for sludge Feeding to filter press complete with all the accessories, motor of required capacity. The pumps shall be complete with Base frame, Delivery header with pressure gauge on delivery line . Pumps = 02 Nos.(1w + 1s) Flow rate (each) = 1 m³/hr Head = 8-10 m

Supply, installation, testing & commissioning of Screens 2 Nos.Mild Steel Suitable Sized Manually operated Bar Screen made of MS in RCC screen channel as per following specifications Cleaning :- Manual Screen MOC :- Complete in MS

Supply, installation, testing & commissioning of Submersible pumps with solid handling capacity upto 30 - 40 mm with CI casing & CI impeller complete with all accessories, motor of required capacity. The pumps shall be complete with Delivery header with, pressure gauge on delivery line with isolation level controller (with wiring) to control the level of Sump automatically. Pumps shall have following duty: Pumps = 02 Nos.(1w +1s) Flow rate (each) = 8.5 m³/hr Head = 8-10 m

Providing and fixing all interconnecting exposed plant piping of required MOC as MS/GI/PVC/CPVC/UPVC and isolation control valves for making the piping arrangement complete within the battery limits.

Supply, installation, testing & commissioning of SBR Based Biological system comprising of the following equipments: Air Blowers For SBR tanks Capacity : 100-300 m3/hr @ 5000-5500 mmwg Type Twin Lobe Qty -2 Nos. (1 w+1s) Disc type Fine Bubble Diffusers Size: 300 mm Dia Decanter system Qty -1 Nos. Type : Moving/Floating MOC : SS-304 Pipes and fittings for Air piping and Air Grid Qty-1 Lot Level transmitter/controller and accessories Qty-1 Lot PLC for SBR system Qty -1 Set

Supplying, installing, testing, commissioning of Centrifugal Horizontal Filter Feed pumps Complete in CI body& CI impeller with motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, strainer at suction. The pump shall be suitable for 415±10% volts 3 phase AC supply . Pumps = 02 Nos.(1w + 1s) Flow rate (each) = 8.5 m³/hr Head = 25 - 30 m

Supply, installation, testing & commissioning of Sludge recirculation/transfer pumps for sludge Feeding to filter press complete with all the accessories, motor of required capacity. The pumps shall be complete with Base frame, Delivery header with pressure gauge on delivery line . Pumps = 02 Nos.(1w + 1s) Flow rate (each) = 1-2 m³/hr Head = 8-10 m

Supply, installation, testing & commissioning of Sludge feed pumps for sludge Feeding to sludge bag system complete with all the accessories, motor of required capacity. The pumps shall be complete with Base frame, Delivery header with pressure gauge on delivery line . Pumps = 02 Nos.(1w + 1s) Flow rate (each) = 0.5-1 m³/hr Head = 25-30 m

Mode of operation: Manual Supplying, installation, testing & commissioning of MSEP/FRP vessel filter with frontal piping and Valves with all the required accessories. Filter shall include media, standard fittings like pressure gauges, sampling cock, rinse drain Multigrade Sand Filter Dia : 1100 mm HOS: 1800 mm Filter media: Fine and coarse sand, pebbles and gravels.

Activated Carbon Filter Dia : 1100 mm HOS: 1800 mm Filter media: Activated Carbon, fine and coarse sand, pebbles and gravels

Water Booster Pumpset (Flushing / Soft Water Supply) Supplying & supervision of testing & commissioning of Booster Pumpset (Hydropneumatic systems) as described below Supplying & supervision of testing & commissioning of package vertical Hydropneumatic system, comprising of 2.0 nos. (1 duty + 1 stand by) Electrical Driven inline pumping sets each of 5.0 LPS to a head to 60 meter with all accessories, Pumps shall be with C.I. Base, S.S 304, impeller, shaft, mechanical seal, S.S. Shaft directly coupled to motor suitable for operation on 400/440 volts, 3 phase 2900 RPM. TEFC electronic motor mounted on a common channel baseplate 150mm dia pressure gauge, GM isolation cock and cement concrete foundation with plaster with dunlop cushy foot mountings with all accessories such as NRVs, valves, pressure switch, common suction and delivery header, bellows on sucton and delivery side complete in all repsects. Pump mounted or wall mounted microprocessor based controller, Electronic control panel with frequency inverter, logic controller relays, pressure sensor, pressure sensor transmitter, electrical wiring, cabling from panel to pumps, level controller, two lined LCD display, diodes to indicate pump ready, pump running and fault capable to communicate with toher RS 485 interface. with Power box equipped with fuses or isolators or circuit breakers as required. complete with all accessories as per manufacturer specifications. Suction & Delivery Header - SS 304 Control Valve On suction and Delivery - Ball Valve Only (No Butterfly Valve Accepted). Flow Prevention - Only Check Valve One Number Variable frequency Drive Impeller : Stainless Steel Shaft : Stainless Steel RPM : 2900. Mover : Electric Motor HP - As required. Necessary foundation with bolts Ball valve on suction & delivery NRV on delivery Dust & vermin proof cubicle type motor control centre fabricated from powder coated 16 SWG MS sheet suitable to automatic working of above mentioned pumps.

Providing, fixing, testing and commissioning of horizontal centrifugal Irrigation water transfer pumps. The pumps shall be made of C.I. casing, CI impeller, SS shaft & sleeve. Mechanical seal connected by to a TEFC induction motor mounted on a common channel base-plate with efficiency class IE3 or EFF-1 whichever is more efficient with coupling guard 150 mm dia pressure gauge with GM isolation cock, suitable vibration eliminator, pads of approved design. Motor to be suitable for 400/440V, 3 phase 50 cycles AC power supply, including all necessary piping, suction and delivery header, individual suction and delivery of pump, valves, NRV, pressure gauge and other accessories and concrete foundation complete as required. Irrigation pumps: Capacity : 5 LPS Head : 50 Mtrs Type of Pump : Horizonal Centrifugal pump No. of Pumps (2 Nos. – 1 W + 1 S)

FIRE-FIGHTING WORKS FIRE PUMPS - ELECTRICAL Supply, installation, testing and commissioning of horizontal single stage centrifugal type factory assembled fire pumps suitable for autometic operation at synchoronous speed of 2900 rpm, TEFC conforming to IP-55 & flexible coupling gaurd mounted on a common structural base plate with 150mm dia gun metal pressure gauges with isolation cock and piping, suitable vibration elimination pads of approved design for pump foundation, motor to be suitable for 415 volts, 3 phase 50 cycles AC. Capacity 2280 LPM at 6.0 Kg/cm2 delivery pressure for Fire Hydrant Network.

Capacity 180 LPM at 6.0 Kg/cm2 (Jockey Pump).

FIRE PUMPS - DIESEL Supply, installation, testing and commissioning of horizontal single stage centrifugal pumping set with CI volute and bronze impeller with mechanical seals directly coupled to automatic Diesel Engine complete with all accessories like self starting by means of Battery powered electric starter motor, Paper Filter type air cleaner, exhaust silencer etc. complete in all respects. The engine & the pump will be mounted on common base plate on anti-vibration mountings. Capacity 2280 LPM at 6.0 Kg/cm2 delivery pressure for Fire Hydrant & Sprinkler Network.

Electric Motor Driven Hose Reel Pump (Location - Roof ) Supplying, installing, testing and commissioning of Fire authority approved Electrical driven fire pump suitable for automatic/ manual operation consisting of the following:Horizontal mounted split casing type fire pump having cast iron body, bronze impeller, stainless steel shaft & capable of delivering 900 LPM against a total head of 35 M while running at 1400 RPM complete with mechanical seal pressure gauge with GM cock on the delivery side of pump and including 50 mm by pass arrangement (with 50 mm valve and up to 5 meter GI class 'B' pipe) for periodical testing of working of pumping test. Squirrel cage, induction motor TEFC type suitable for 415 + 10%V, 1 phase, 50 Hz, AC supply, of suitable HP rating for the above pump with synchronous speed of 1400 RPM with flexible coupling and coupling guard . Common bed plate for mounting pump and motor fabricated of mild steel channel as per manufacturer's recommendation with heavy duty Anti Vibration pads (4 Nos., heavy duty). Coupling and coupling guard for direct coupling of pump and motor. Drain Pipe with Valve (50 mm dia) Hose Reel Pump Discharge : 900 LPM App. Head : 35 m App. HP : 15.0

PANELS: Supply, installation, testing and commissioning of followingintegrated, cubicle type,dead front, extensible, sheet steel control panel. The panel shall be suitable for 440 volts, 50 cycles, 4 wire supply The following components and accessories shall be mounted with ineach control panel. One no 100 amps TP incoming MCCB with the following:0-500 volts 96 x96 square mm voltmeter with slector switch and control fuses- 1 SET 0-100 amps 96 x96 square mm ammeter with CT's and slector switch- 1 SET Phase indicating lamp with toggle switches. Indication lamps for ON/OFF/TRIP status Outgoing Feeders / Starters as below:100 ATP MCCB with star / delta as starter suitable for 30 HP motor for Downcomer Pump - 1 SetProvision in control panel to connect flow switch for autmatic operation of roof fire pumps. Discharge : 450 LPM App. Head : 35 m App. HP : 15.0

Exhaust piping Providing & fixing 150 mm diameter M.S. Class 'C' diesel pump exhaust pipe includings all fittings, like bends, tees etc. clamps / structural steel supports. The pipe shall be provided with 75mm thick fiberglass insulation & covering the insulation with 500 g polythene sheet giving proper overlaps & sealing the joints with suitable adhesive compound. The pipe shall be provided with 24 gauge aluminium sheet cladding

PRESSURE SWITCH Supplying, installing, testing and commissioning 0 to 12 Kg/ cm2 ON/OFF pressure switch in delivery line of pump along with control wiring for auto starting and auto stopping of hydrant and jockey pumps.

Supply, fabrication (as per code), installation, testing and commissioning of Air vessels 250mm diameter and 1200mm high fabricated from 8mm M.S. plate with accessories inside painting with epoxy paint and outside with enamel.

Providing, fixing, testing & commissioning of resilient rubber lined single arch vibration eliminators suitable for raw water up to 45 deg. C temperature, working pressure 8.8 Kg/cm2 and test pressure 14 Kg/cm2 for :- 150 mm dia

100 mm dia

80 mm dia

Fire Hose Cabinet Supply, installation, testing, trial run and commissioning of hydrants all complete as required and as approved Providing and fixing angle iron (40 mm x 40 mm x 5 mm) MS door frame 900x2100 door capable of accommodating fire hose reel, landing valve, hose pipes, fittings & accessories. The door shall have a front glass with lock and key arrangement & shall be painted with post office red colour (approval shall be taken on the basis of submitted sample before ordering) Cost of fire extinguishers not included in item rate. (Liasioing with civil contractor for making 900x600x2100 Recessed type mansoary box (by civil contractor).

Providing and fixing of TAC approved 1.6mm thick M.S. fire hose cabinet (750x600x250mm) made out of 16 gauge M.S. sheet capable of accommodating landing valve, hose pipes, fittings & accessories. The box shall have a front glass door with lock and key arrangement & shall be painted with post office red colour (approval shall be taken on the basis of submitted sample before ordering) - for external and roof hydrant.

Providing and fixing of 63mm dia single outlet GM landing valve IS marked with suitable size bolts, nuts, washers and gaskets. Landing valve shall be TAC Approved Make.

Providing and fixing of 63mm dia twin outlet GM landing valve IS marked with suitable size bolts, nuts, washers and gaskets. Landing valve shall be TAC Approved Make.

Providing and fixing of First aid hose reel with 25 mm dia, 30 m long rubber hose, ball valve, piping and GM nozzle

Providing and fixing of 63mm reinforced rubber hoses (RRL) with male and female GM coupling, IS marked- 15 m long

Providing and fixing of standard short size GM branch pipe with nozzle of 20mm nomnal bor outlet with instaneous type 63 mm dia coupling complete IS marked & TAC approved.

Fire Axe

Providing and fixing of ss orifice plates in pipelines to reduce pressure from 8 kg. to 3.5 kg/sq.cm.

Providing, installing, testing & commisioning of fire brigade inlet connection (fire department connection) consisting of 4 Nos. 63 mm dia instantaneous inlet arranged on a 50 mm dia header, 1 No. 150 mm diameter Butterfly valve, 1 No. 150mm dia. Non-return valve and wall mounted box of M.S. construction with glass door to house the above mentioned components.

Providing, installing, testing & commisioning of fire brigade draw out connection (fire department connection) with suction pipe MS class 'C' 100 mm dia. & 100 mm dia. foot valve & steel chain including wall mounted box M.S. construction with glass door to house the above mentioned componenets.

Providing and fixing up to floor five level precast cement concrete string or lacing courses, copings, bed plates, anchor blocks, plain window sills, shelves, louvers, steps, stair cases, etc. including hoisting and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), cost of required centering, shuttering and finishing smooth with 6mm thick cement plaster 1:3 (1 Cement : 3 fine sand) on exposed surfaces complete. 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20mm nominal size).

Constructing masonary chamber 90 x 90 x100 cm. inside with 75 class designation brickwork in cement mortar 1:5 ( 1 cement : 5 fine sand) for sluice valve with CI surface box 100 mm top dia. 180 mm bottom dia. And 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) necessary excavation foundation concrete 1 :5 :10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size and inside plastering with 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design with FPS bricks

Providing & Fixing C.I.sluice valve(with cap) complete with bolts,nuts,rubber insertions etc.(the tail pieces if required will be paid separately) 150 mm dia.pipe ; Class II

Y - STRAINER of Ductile CI Body flanged ends with stainless steel strainer for chilled / hot water circulation including insulation as specified. 150 mm dia.

NON - RETURN VALVE with dual plate of C I body SS plates vulcanized NBR seal flanged end & PN 16 pressure rating as 150 mm dia

BUTTERFLY VALVE (MANUAL) with C I body SS disc nitrile sheet & O - ring & PN 16 pressure rating as specified. 150 mm dia

200 mm dia

Providing and fixing in position the industrial type Pressure Gauges with gun metal / brass valves complete as required

Providing laying, testing & commissioning of “C” class heavy duty MS pipe conforming to IS 1239/3589 (all pipes shall be ISI marked and of makes specified in the specifications) including DI FORGED fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including excavation & providing cement concrete blocks as supports and anti-corrosive treatment to burried pipes by wrapping & coating with 4 mm thk. (OR 2 COATS of 4.0mm thick tape) anticorrosion tape along with two coat of black japan primer for under-ground pipe . 150 nominal bore (class C)

100 nominal bore (class C)

Providing, laying, testing & commissioning of “C” class heavy duty MS pipe conforming to IS 3589 and 1239 (all pipes shall be ISI marked and shall be one of approved makes) including DI FORGED fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. fixing the pipe on the wall/ceiling with suitable clamps and painting with two or more coats of synthetic enamel paint of required shade complete as per specificatipns and as required. (Above Ground) Threaded joint upto 50mm diameter pipe. Welded joint above 50mm diameter pipe. 200 mm nominal bore (class C)

150 mm nominal bore (class C)

100 mm nominal bore (class C)

80 mm nominal bore (class C)

65 mm nominal bore (class C)

50 mm nominal bore (class C)

40 mm nominal bore (class C)

32 mm nominal bore (class C)

25 mm nominal bore (class C)

Supply, installation, testing and commissioning of 150 mm dia Installation Control Valve inclusive of 2 nos 150 mm dia Butterfly Valve, strainer, Alarm Valve with Water Motor Gong, Pressure Gauges, Test Lines with Ball Valves with necessary GI (H) piping with threaded fittings of required sizes complete

Providing and fixing carbon-di-oxide type fire extinguishers consisting of welded M.S. cylindrical body, internal discharge tube, discharge nozzle, suspension bracket, conforming to IS 15683, finished externally with red enamel paint and fixed to wall with brackets complete with internal charges. Capacity 4.5 kg

Providing and fixing (ABC Dry Chemical Powder ) type Fire Extinguisher of Capacity 6 kg Confirms to IS 15683, bearing ISI mark complete with brass forged squeeze grip type valve fitted with pressure gauge , pressurize with dry Nitrogen gas filled, with discharge nozzle with wall mounting bracket complete with internal charges. Capacity 6 Kg.

Providing and fixing mechanical foam type Trolley Mounted Fire Extinguisher of bearing to IS:10568/IS13385/IS13386 with dis Capacity 45 Lit.

Providing and fixing Carbon Dioxide Type Trolley Mounted Fire Extinguisher of as per IS: 2878 with discharge time of 10 to 20 sec/15 to 36sec/20 to 60sec respectively. 22.5 Kg. CO2 Fire Extinguisher

Supplying and Earthing with GI earth plate 600mm x 600 mm x 6mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc, with charcoal/ coke and salt as required.

Laying and fixing of One number PVC Insulated and PVC Sheathed/XLPE power cable of 1.1 kV grade of folloing size on wall surface as required. Aboved 35 sq mm and upto 95 sq mm (clamed with 25x3mm MS flat clam)

Supplying of all materials and making terminations of 1.1 KV grade aluminium multicore cables of the following sizes. The work includes cable glanding using brass plated double compression glands, sizing the core leads, removing insulation, fixing suitable crimping type copper lugs/ thimbles by using hydraulic crimping tools with correct size of the dies, shaping the leads and neatly connecting the same to the equipment terminals. 3.5 Core 16 sq. mm. Armoured Aluminium cable.

Control Cabling (PVC insulated and PVC sheathed, armoured, Copper Conductor of 1.1 KV grade on existing cable trays). 5C x 1.5 Sq. mm

Exhaust piping PRESSURE SWITCH Supplying, installing, testing and commissioning 0 to 12 Kg/ cm2 ON/OFF pressure switch in delivery line of pump along with control wiring for auto starting and auto stopping of hydrant and jockey pumps.

Providing, fixing, testing & commissioning of resilient rubber lined single arch vibration eliminators suitable for raw water up to 45 deg. C temperature, working pressure 8.8 Kg/cm2 and test pressure 14 Kg/cm2 for :- 150 mm dia

Supply, installation, testing and commissioning of 150 mm dia Zonal Control Valve inclusive of 1 nos 150 mm dia butterfly valve, 150mm diam. non return valve, Flow Switch, water pressure gauges & 25 mm dia. Auxillary Drain valve with sight glass with necessary GI (H) piping with threaded fittings of required sizes complete 150 mm dia butterfly valve 150mm diam. non return valve Flow switches in 150 mm. dia M.S. Pipe pressure gauges Pressure gauges in the M.S. Pipe Line including connection etc. as required. 25 mm dia. Auxillary Drain valve Sight glass

Providing, fixing, testing and commissioning of quick response 15 mm dia. gunmetal quartz bulb type sprinkler head to operate at 68 degree centigrade Pendent /Upright type

Providing and fixing carbon-di-oxide type fire extinguishers consisting of welded M.S. cylindrical body, internal discharge tube, discharge nozzle, suspension bracket, conforming to IS 15683, finished externally with red enamel paint and fixed to wall with brackets complete with internal charges. Capacity 4.5 kg

H.T. Cable Laying & Terminations (Cable Quantiities will be checked at site & got approved from Engineer In charege before procurement/ execution.) Supplying, laying and fixing of the following sizes earthed amoured aluminium conductor XLPE power cable of 11 KV grade confirming to IS 7098(Part II) amended upto date of following sizes on existing cable tray as required. 3 x 300 Sq.mm

Supplying and making indoor cable end terminations with heat shrinkable jointing kit complete with all accessories including lux suitable for following size of 3 core XLPE AL conductor cable of 11 KV grade as required. 300 Sq.mm

Supplying, Assembling, Transportation of 800 KVA 11KV/.433KV, Dyn11, 3phase 50Hz, outdoor type copper wound, Oil type step down transformer i/c oil complete with all modern fittings as required including , lifting lugs, Roller type non-directional wheels, suitable weatherproof boxes on both the ends for cable entry, disconnecting chamber on both sides, winding temprature indication & alarm, bucholz relay , earthing terminals, diagram and rating plate, explosion vent, OFF load tap changer (+5% & -10%) @ of 2.5% steps etc., as required.Transformer oil with tapping quantities of oil to be supplied separately etc. Losses @ 50% Loading : 2287 W Losses @ 100% Loading : 6402 W Temp. Rise : 40/45 Deg C ( Oil/Winding) % Z : 4.5% (Subj. to IS Tol.) complete as required. as per IS :1180 Level -2 Transformer As Above

Main LT Panel With PLC Assembling,loading,unloading,shifting,erecting,testing and commissioning of 415V, 3 Phase, 50 Hz., 4 wire system, sheet steel clad, dust and vermin proof cubical and Indoor type floor mounted, free standing extendible type Main LT Auto Load Management Panel compartmentalized design and fabricated out of 2 mm CRCA sheet steel complete with suitable size of Aluminium Bus bars, Electrical interlocks as per the various status of all the equipments indicated on the drawings. Providing & Fixing of base plate / channel, P/F the following Switchgears, complete with earth Bus bar throughout the length of the panel, terminal arrangement for Incomings / Outgoings cables and also outgoing terminations for various sizes of cables, The incoming and outgoing feeders shall be accommodated in a modular multi-tier arrangement, adequate size bus duct/ cable alley, Painting, Earthing, Numbering, Danger plate etc. complete as required as per specifications and drawing attached. (Panel should have proper arrengments for future expension, etc. complete as required.) Incomers: 1 No., 1250 A, 415V, 50 KA (Ics=Icu=Icw =50 KA for 1 second), 4 Pole, Electrical draw out type, Electrically interlocked, Micro-processor based release (for over current and Earth fault protections) A.C.B. with all indications, metering, protections, push buttons etc. complete in all respects as mentioned in specifications and as required. Each ACB shall have minimum following accessories: (Transformer Incomer) Digital flush type class -I accuracy multifunction meter with power load manager ,showing V, A, PF, KVAH, KWH etc. with 3 Nos. current transformers of 1250/5 ratio, 15 VA Class 1.0 metering. (Transformer)

Automatic P.F.C.R. 9 stage with power factor meter & CT's for unbalanced load - 1 Set. Busbar : TP aluminium extensible type main bus bars of minimum of 300 Amps. capacity & auxiliary Bus Bars of suitable capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 35ka capacity. Outgoings :- Control MCB/ MCCBs with capacitor banks: 125Amp. TP MCCB '35ka' Thermal Magnetic release having O/L & S/C protection with 50 KVAr, 415V (fixed) Heavy duty capacitor bank etc. - 1 set. 125Amp. TP MCCB '35ka' Thermal Magnetic release having O/L & S/C protection with 50 KVAr, 415V Heavy duty capacitor bank etc. - 2 set. 63Amp. TP MCCB '35ka' Thermal Magnetic release having O/L & S/C protection with 25 KVAr, 415 V Heavy duty capacitor bank, Capacitor Duty Contactor etc - 2 sets. 40Amp. TP MCCB '10ka' Thermal Magnetic release having O/L & S/C protection with 20 KVAr, 415 V Heavy duty capacitor bank, Capacitor Duty Contactor etc - 3 sets. 32Amp. TP MCB '10ka' Thermal Magnetic release having O/L & S/C protection with 10 KVAr, 415 V Heavy duty capacitor bank, Capacitor Duty Contactor etc - 1 sets. 25Amp. TP MCB '10ka' Thermal Magnetic release having O/L & S/C protection with 5 KVAr, 415 V Heavy duty capacitor bank, Capacitor Duty Contactor etc - 1 sets. Capacitor Panel as above

OPD Block-F Panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 400 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 500 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 200amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 2 Nos. (1 No. Spare) 100amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 3 Nos. (1 No. Spare) 63amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 3 Nos. (1 No. Spare) 63A 4P MCB '10kA' - 3 nos. Panel describe as above

Equipment Panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 200 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 250 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 100A 4P MCCB '25kA' - 3 nos. (1 no. spare) 63A 4P MCB '10kA' - 8 nos. (2 no. spare) Panel describe as above

Light & Power Panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 100 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 250 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63A 4P MCB '10kA' - 13 nos. (3 no. spare) Panel describe as above

Ups Panel Supplying, assembling, erecting, connecting, testing and commissioning of dust, damp and vermin proof wall mounting factory built sheet steel enclosed non-drawout modular type Panel fabricated out of suitable sized angle iron and flats, base channel and covered with 2.0mm thick CRCA sheet, duly painted complete with earth bus, aluminium bus bar, numbering & sign writing, interconnection & including the cost of connection through bus bar / copper conductor flexible connection with necessary interlocking with existing panel as shown in drawing as per specification and mounted with the followings. Incoming: 1 Nos. 63amps, 415V 4P MCCB '16ka' with overcurrent and short circuit Microprocessor based release. 1 Set of three phase R,Y,B, ON indicating lamps, along with 2A SP MCB backup protection. Bus Bars: Electrolytic high conductivity aluminium Four Pole (full rated)busbars rated at 433V,50 Hz., 100 amps, 16kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63 Amp 415 volts, Four Pole,10 KA MCB- 5 No. (2 spare) Panel as above

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing / wall mounted factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming i) 1 No. - 63 amps four pole MCCB (25 KA) with following accessories: a) 3 Nos. Phase indication LED lamps with 2Amp back up MCB, breaker 'ON/OFF' indicating light with 2A MCB b) Set of Digital flush type class 0.5 accuracy multifunction meter, showing V, A, PF, Hz, KW, KWH, KVAR, etc. and 3 Nos. cast resin current transformers of 63/ 5 Amp ratio, 15 VA Class 0.5 metering. Bus Bar : 4P aluminium extensible type main bus bars of minimum of 100 Amp capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete. Outgoings: 3 Nos. - 63 Amp. four pole (10kA) (1 Nos. Spare) 2 Nos. - 32 Amp. DP (10kA) MCB Each outgoing breaker shall have the following accessories- a) LED indication lamps with 2Amp back up control MCB for breaker 'ON/OFF' including terminal extension spreaders for all MCCB's. Lift Panel described as above

IPD Block-A Panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 200 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 250 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 125amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 2 Nos. (1 No. Spare) 100amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 2 Nos. (1 No. Spare) 63amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 1 Nos. 63A DP MCB '10kA' - 2 nos. (1 No. Spare) Panel describe as above

Light & Power Panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 125 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 160 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63A 4P MCB '10kA' - 15 nos. (3 no. spare) Panel describe as above

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing / wall mounted factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming i) 1 No. - 63 amps four pole MCCB (25 KA) with following accessories: a) 3 Nos. Phase indication LED lamps with 2Amp back up MCB, breaker 'ON/OFF' indicating light with 2A MCB b) Set of Digital flush type class 0.5 accuracy multifunction meter, showing V, A, PF, Hz, KW, KWH, KVAR, etc. and 3 Nos. cast resin current transformers of 63/ 5 Amp ratio, 15 VA Class 0.5 metering. Bus Bar : 4P aluminium extensible type main bus bars of minimum of 100 Amp capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete. Outgoings: 2 Nos. - 63 Amp. four pole (10kA) (1 Nos. Spare) 2 Nos. - 32 Amp. DP (10kA) MCB Each outgoing breaker shall have the following accessories- a) LED indication lamps with 2Amp back up control MCB for breaker 'ON/OFF' including terminal extension spreaders for all MCCB's. Lift Panel described as above

IPD Block-D Panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 200 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 250 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 125amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 2 Nos. (1 No. Spare) 100amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 2 Nos. (1 No. Spare) 63A DP MCB '10kA' - 2 nos. (1 No. Spare) Panel describe as above

Light & Power Panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 125 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 160 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63A 4P MCB '10kA' - 9 nos. (3 no. spare) Panel describe as above

Bmw Panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 100 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 125 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 3 Nos. (1 No. Spare) 63A FP MCB '10kA' - 2 nos. (1 No. Spare) 63A DP MCB '10kA' - 1 No. Spare Panel describe as above

Laundry Panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 100 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 125 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 2 Nos. (1 No. Spare) 63A FP MCB '10kA' - 2 nos. (1 No. Spare) 63A DP MCB '10kA' - 1 No. Spare Panel describe as above

Supply, laying, testing and commissioning of 1.1 kv grade XLPE insulated PVC sheathed steel armoured alluminium stranded conductor ISI marked LT Cables in trenches/ ducts/ through RCC pipes under roads/ on cable trays of following sizes, complete all as specified (as per CPWD specifications for External Electrical works), i/c clamping, dressing, earth work digging, sand filling, bricks protection, back filling etc. as required & approved by Engineer's Incharge. (Tagging to be provided with aluminium strips on both the ends as approved). 3½ core X 300 Sq.mm.

3½ core X 240 Sq.mm.

3½ core X 185 Sq.mm.

3½ core X 150 Sq.mm.

3½ core X 95 Sq.mm.

3½ core X 70 Sq.mm.

3½ core X 50 Sq.mm.

3½ core X 35 Sq.mm.

3 core X 10 Sq.mm

3 core X 6 Sq.mm

4 core X 25 Sq.mm

4 core X 16 Sq.mm

4 core X 10 Sq.mm

4 core X 6 Sq.mm

Supplying and making cable end termination with brass compression glands and aluminium lugs including inhibiting compound to be used in each lug, for the following XLPE aluminium conductor armoured cables of 1.1 KV grade etc, complete as required. 3½ core X 300 Sq.mm.

3½ core X 240 Sq.mm.

3½ core X 185 Sq.mm.

3½ core X 150 Sq.mm.

3½ core X 95 Sq.mm.

3½ core X 70 Sq.mm.

3½ core X 50 Sq.mm.

3½ core X 35 Sq.mm.

3 core X 10 Sq.mm

3 core X 6 Sq.mm

4 core X 25 Sq.mm

4 core X 16 Sq.mm

4 core X 10 Sq.mm

4 core X 6 Sq.mm

Laying and fixing of one number PVC insulated and PVC sheathed/XLPE power cable of 1.1 KV grade of following size on cable tray as required. Upto 35 sq. mm (clamped with 1mm thick saddle)

Above 35 sq. mm and upto 95 sq. mm (clamped with 25x3mm MS flat clamp)

Above 95 sq. mm and upto 185 sq. mm (clamped with 25/40x3mm MS flat clamp)

Above 185 sq. mm and upto 400 sq. mm (clamped with 40x3mm MS flat clamp)

Supply, fabricating and installing following size of G.I. perforated type cables trays including suspending from ceiling with MS angle, rods connection pieces, (L pieces, T pieces, 90/45 degree/ any other fitting required.) G.I. nut bolts, G.I. washers, fasteners etc. complete in all respect as required at site as required & approved by the Engineer Incharge. 600 mm width X 62.5 mm depth X 2.0 mm thickness

450 mm width X 62.5 mm depth X 2.0 mm thickness

300 mm width X 62.5 mm depth X 2.0 mm thickness

150 mm width X 50 mm depth X 1.6 mm thickness

100 mm width X 50 mm depth X 1.6 mm thickness

50 mm width X 50 mm depth X 1.6 mm thickness

Supply, assembly and laying of under floor trunking made out of min. 1.5mm thick (Pregalvanized) GI sheet complete with jointing coupler, fixing bracket, sleeve, horizontal bends, floor, vertical bends, level adjustment components and closer, vertical elbow, removable covers, compartments created with partition should be clinched to the body etc. access outlet. etc. complete with all other accessories under floor installation including cutting and chasing the floor/ or on surface, making good the same, placing in position and cleaning from inside complete etc. as required. 250 mm x 38 mm (3 compartment)

150 mm x 38 mm (2 compartment)

100 mm x 38 mm (2 compartment)

50 mm x 38 mm (1 compartment)

Supply, assembly and laying of under floor, height adjustable junction box, supplied completely with base and cover plate floor installation including cutting and chasing the floor/ or on surface, making good the same, placing in position and cleaning from inside complete etc. as required. 250 mm x 38 mm (3 compartment)

150 mm x 38 mm (2 compartment)

100 mm x 38 mm (2 compartment)

50 mm x 38 mm (1 compartment)

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 meter long etc. with charcoal/ coke and salt as required.

Providing, laying, fixing, connecting and testing of undernoted sizes of copper strip/ GI strip/ wire from earth electrode to equipment loop and earthing system, in trenches, on surfaces, along pole or along M.S. support, etc. including excavation where required for laying the copper strip/ GI strip and filling back complete, conforming to relevant IS and all as specified. GI strip 50mm x 6mm on surface or in recess etc.

CU strip 25mm x 3mm on surface or in recess etc.

50mm dia GI pipe 'B' under floors/ paving area's etc.

6 SWG G.I. wire

Providing and fixing 25 x 5 mm G.I. Strip in 40 mm dia. G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Supply and fixing in position 1000mm wide checkered rubber matting of 1.1KV grade as per electricity rules, with thickness not less than 12mm.

Supply and fixing in position the best quality L.T. Danger Notice plate of 200mm x 150mm,made of mild steel atleast 2mm thick and vitreous enamelled, white on both sides and with inscription in signal red colour on front side written in English & Hindi as required.

Supply and fixing in position the best quality H.T. Danger Notice plate of 250mm x 200mm made of mild steel atleast 2mm thick and vitreous enamelled, white on both sides and with inscription in signal red colour on front side written in English & Hindi as required.

Supply and fixing in position the approved shock treatment / restoration charts written in Hindi and English duly framed in teak wood frame and covered with 2.8mm glass as required.

Supply,Installation,Testing and Commissioning of following size of FRLS PVC insulated armoured copper contol cable. 6C X 1.5 sqmm

Supplying and fixing of fire buckets 5 Nos.in each set of approved quality, red painted from outside and white from inside conforming to IS : 2546/1974 with additional handle at the bottom, filled with fine sand and fixed on an angle iron frame as per the requirement of local authorities.

Supplying and fixing of MS pedestal stand suitable for supporting four buckets as required.

Supplying and fixing First Aid Box of 18 S.W.G. M.S sheet,painted as approved & prescribed by Indian Red Cross Society & as per attached specifications.

Supplying and fixing of caution Boards of 16 S.W.G. , M.S. sheet of 300 mm x 150mm size, duly painted & having "MAN ON LINE' & "DO NOT SWITCH ON' written in Red complete with hanging arrangement as required.

Supply and fixing in position the approved single line diagram framed in 1000 x 800 mm size glass framed and installed in main switch room.

Supply of tool kit with 1 pair,11KV rubber hand gloves of aproved make.

Supply and fixing of Insecticuters for Kitchen.

Installation of Air Curtain

Supply and laying of GI pipe under road / paved area crossing etc. including excavation, back filling, ramming and making good. 150 mm dia pipe

200 mm dia pipe

Supply and installation of following RCC (NP-2 class) Hume pipe under paved areas , including providing 75mm thick cement concrete all around pipe 1:3:6 ( 1 cement, 3 coarse sand and 6 crushed stone aggregate ) 100 mm dia ID

150 mm dia ID

Supplying and laying of RCC (NP-2 class)pipe in ground for cable protection as required. 100 mm dia

200 mm dia

300 mm dia pipe

Supply, fixing, testing and commissioning of automatic Linear pneumatic Tube Detection based Novec 1230 System for Electrical Panels (Linear Pnuematic Heat Detection Tube Panel Protection System), consisting of the Mentioned components 4 Kg capacity Novec 1230 , DLP Assembly with automatic valve, push in connector for tube, 4Kg Novec 1230 gas , mounting bracket, End of Line adopter and low pressure switch for monitoring system activation.

Linear pneumatic heat Detection Tube with all necessary fittings & supports.

Master Control Unit for controlling each system, complete with pressure switches, buzzers and electronic hooters, including all necessary accessories + electrical wiring to make each entire system functional.

Supplying, Installation, Testing and Commissioning of single spike air terminals of 10mm dia.of 1000mm length as required and as per site conditions. The air terminal shall be manufactured with aluminium. The terminal shall be provided with the two side wall clamp to mount the air terminal and as per site condition and shall meet the requirement of IEC 62561-2.

Roof Conductor for Parapet/Mesh : Supplying, Installation, Testing and Commissioning of 8 mm dia aluminium round conductor for air termination network at roof and shall meet the requirement of IEC 62561-2.

Supplying, Installation, Testing and Commissioning of Parapet Conductor holder for holding of 8 mm dia. round conductor (for RCC Roof). The conductor holder should be installed at every 1 mtr.The conductor holder shall be screw less type holder as per IEC 62561-4.

Supplying, Installation, Testing and Commissioning of glue.

Supplying, Installation, Testing and Commissioning of Dispenser

Supplying, Installation, Testing and Commissioning of 16sq.mm. copper cable along with lugs, having 500mm length & as per IEC 62561-1 so as to connect air termination rod with any metallic structure on the roof

Supplying, Installation, Testing and Commissioning of Straight - Connector for making straight joint of 8 mm Stainless Steel Conductor to 8 mm dia Stainless Steel conductor on parapet wall, roof and vertical facade of mesonery / glass / metalic work

Supplying, Installation, Testing and Commissioning of T - Connector for making Tee joint of 8 mm dia. Stainless Steel Conductor to 8 mm dia Stainless Steel conductor on parapet wall, roof and vertical facade of mesonery / glass / metalic work.

Supplying, Installation, Testing and Commissioning of X - Connector for making Cross joint of 8 mm Stainless Steel Conductor to 8 mm dia Stainless Steel conductor on parapet wall, roof and vertical facade of mesonery / glass / metalic work.

Supplying, Installation, Testing and Commissioning of 8 mm dia aluminium round conductor for Down conductors to be installed on vertical wall or façade of masonary / glass / metalic work, It shall meet the requirements of IEC 62561-2.

Supplying, Installation, Testing and Commissioning of Wall Conductor holder for holding 8 mm dia. round conductor (for RCC wall). The conductor holder should be installed at every 1 mtr. The conductor holder shall be made with SS clamp mounted on plastic base support & as per IEC 62561-4.

Supplying, Installation, Testing and Commissioning of Test Clamp to disconnect the down conductor from the earth termination network for regular checks of the earth termination resistance value. (with enclosure). It shall meet the requirements of IEC 62561-2.

Supplying, Installation, Testing and Commissioning of Expansion piece made of 8mm dia. Aluminium & as per IEC 62561-2 along with suitable connecting accessory. It shall be installed at every 20 mtr to maintain the flexibility to the conductor due to heat.

Supplying, Installation, Testing and Commissioning of Lightning Strike counter Model: JMV 6D for counting thenumber of lightning strikes without any powersupply. The Counter should be mounted on the Down Conductor. The LightningCounter should be IP65 rated enclosure suitablefor external application.

Supplying, Installation, Testing and Commissioning of Earthing termination made of copper-bonded rod of 10 feet length,14.2 mm dia. (Minimum copper bonding shall be 0.25mm) as per IS 3043, IEEE-80, NBC 2016 along with Rod-to-Conductor connectors, Earth enhancement material some with resistivity of 0.12 ohm-mtr, and complying IEC 62561-7 and Pit Cover complying IEC 62561-5 and other accessories as required and as per specification and other applicable codes.

Supplying, Installation, Testing and Commissioning of 10mm CCS Conductor laid at 600mm below the ground, as Required and as per specification and code of practice with exothermic joint.

Supplying, Installation, Testing and Commissioning of Class B/Type I Single Phase Surge Protection Devices as per IEC 62305-4 and tested according to IEC 61643 – 11, DIN Rail mountable with Maximum Continuous Operating Voltage of 320 V and Voltage Protection Level of 1.3 kV (L-N). Response Time should be less than 100 ns (L-N & N-PE). The maximum impulse test current should be 65 kA (10/350 µs) per pole and 100 kA (10/350 µs) neutral to protective earth. The surge protection devices shall be enclosed in polycarbonate enclosure of IP 65 rating.

Supplying, Installation, Testing and Commissioning of Class C/Type II Single Phase Surge Protection Devices as per IEC 62305-4 and tested according to IEC 61643 – 11, DIN Rail mountable with Maximum Continuous Operating Voltage of 320 V and Voltage Protection Level of 1.3 kV (L-N). Response Time should be less than 25 ns per pole and less than 100 ns between neutral to protective earth. The maximum impulse discharge surge current should be 40 kA (8/20 µs) per pole and 60 kA (8/20 µs) neutral to protective earth. The surge protection devices shall be enclosed in polycarbonate enclosure of IP 65 rating.

SITC of LED Street light : in die-cast aluminium and designed with a very small surface exposed to wind. Cooling fins are integrated into the cover the heat dissipation system is specially designed and made to allow the operation of the LED lights with temperatures ensuring excellent performance/efficiency and durability.minimum system lumen package should be 6200-6300 lm at 6500k, CRI is 80, minimum ,System wattage should be maximum 50W , IP66, IK10LED: Power factor ≥0.9.Luminous flux maintenance 80%: 50.000h (L80B20).Beam should be Wide .Fixture voltage range would be100-300V/AC 50/60Hz,Fixture should have reputaed LED like lumiled, cree or Nichia

SITC of 6000 mm high hot dip GI step Pole. The bottom section of the pole not less than 114mm dia x2000mm long mm and Top Section of the Pole is of 89mm dia x 4000mm long Including bracket. The thickness of the pole sections shall be as per Medium class as per IS:1161. A service window with proper strengthening to cut out door shall be provided to accommodate a 6 amp SP MCB and 32 amp heavy duty connector for mains connections in the bottom part of the pole. The bottom part and the top part of the pole shall be joined together. flanges & shall be welded properly. Cast Aluminium embellishments shall be fitted and sealed by grub screw fixing. A mild steel base plate of 300 mm x300mm x15mm thick with stiffeners shall be welded at the bottom of the pole . The pole shall be hot dip galvanised after fabrication and duly pre treated and painted in U.V. ray resistant P.U. coating in approved colour shade.

Supplying and drawing following sizes of PVC insulated PVC sheathed copper conductor unarmoured multicore cable in the existing poles and bracket from cable termination connector to the fitting i/c providing suitable copper lugs connections etc. as reqd. 3 core 1.5 sq.mm.

marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 90 mm dia (OD-90 mm & ID-76 mm nominal)

Supply of following size of 1.1KV grade multicore aluminium conductor XLPE insulated and PVC sheathed armoured cable in existing trenches/ hume pipe/in ground as per IS : 7098:1988 with upto date amendments. 3c x 16 sq.mm

3c x 10 sq.mm

3c x 6 sq.mm

Providing, laying and fixing following dia RCC pipe NP 2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc. as required. 150 mm dia.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.c with cover & chamber. Complete in all respects as per direction of E/I. HT VCB 3 No's Panel Board Supply,transporting,loading & testing (pre dispatch) of indoor type floor mounted metal clad, 11 KV VCB panel with 3 No. VCBs(1 Incoming , 2 outgoings), totally enclosed & fully interlocked, horizontal drawout, horizontal isolation type breaker as per IS 13118, as amended up to date and additional specifications, having capacities as mentioned below, single break, trip free mechanism, motorised charged and electrical/manually operated (by default) breaker suitable for use on 11 KV, 3 Phase, 50Hz A.C. supply with short circuit fault level of 350 MVA,

H.T. Cable Laying & Terminations (Cable Quantiities will be checked at site & got approved from Engineer In charege before procurement/ execution.) Supplying, laying and fixing of the following sizes earthed amoured aluminium conductor XLPE power cable of 11 KV grade confirming to IS 7098(Part II) amended upto date of following sizes on existing cable tray as required. 3 x 300 Sq.mm

Supplying and making indoor cable end terminations with heat shrinkable jointing kit complete with all accessories including lux suitable for following size of 3 core XLPE AL conductor cable of 11 KV grade as required. 300 Sq.mm

Oil Type Transformer (1000KVA) Supplying, Assembling, Transportation of 1000 KVA 11KV/.433KV, Dyn11, 3phase 50Hz, outdoor type copper wound, Oil type step down transformer i/c oil complete with all modern fittings as required including , lifting lugs, Roller type non-directional wheels, suitable weatherproof boxes on both the ends for cable entry, disconnecting chamber on both sides, winding temprature indication & alarm, bucholz relay , earthing terminals, diagram and rating plate, explosion vent, OFF load tap changer (+5% & -10%) @ of 2.5% steps etc., as required.Transformer oil with tapping quantities of oil to be supplied separately etc. Losses @ 50% Loading : 2790 W Losses @ 100% Loading : 7700 W % Impedance 5% ( Subj. to IS Tol.) Temp. Rise : 40/45 Deg C ( Oil/Winding) complete as required as per IS :1180 Level -2 Transformer As Above

Main LT cum Synchronization panel Supply, installation, testing and commissioning of dust, damp and vermin proof cubicle free floor, indoor type factory built sheet steel enclosed modular bolted construction extendable MAIN LT PANEL CUM SYN. PANEL, suitable for operation on 415 ± 10% volts, 50 Hz AC 3 phase 4 wire supply system fabricated out of suitable sized square tubular section and covered with CRCA sheet steel of 2mm thick for frame work and covers, 3mm thick for gland plates i/c cleaning & finishing complete with 7 tank process for powder coating in approved shade, having extensible type TPN Aluminium bus bars of high conductivity, SMC bus bar supports, with bottom base channel of section not less than ISMC 75mm, fabrication shall be done in transportable sections, entire panel shall have a common G.I. earth bus bar to switch gears with required size of Alum. bus bars and inter-connection with solid copper conductor wires / aluminium strips, neutral links, including control wiring with 1.5 / 2.5sqmm. PVC insulated FRLS copper conductor Single Core cable, cable alleys, cable gland plates in two half, etc. necessary metering protections & indications and mounted with the following switch gears as per drawing and technical specifications etc. complete as required. Incoming & outgoing bus ducts/ cables will be from bottom & top both sides as per site requirement. Proper heat dissipation system should be provided in the panel. Panel should have converter from Modbus to Ethernet for energy meters etc. complete as required. Section- 1 Incomers: 1600 Amp. 4 Pole ACB - 1 set (For DG supply) 1600 Amp. 4 Pole ACB - 1 set (For Transformer supply) Air Circuit Breaker Horizontal drawout type of fault breaking capacity 50KA (Ics=lcu=Icw) Electrical Draw Out Motorized operated, fitted with interlocked door, automatic safety shutters, mechanical ON/OFF and service/ test/isolated position indicators and frame earthing contact, conforming to IS-13947-2 1993 as amended up-to-date complete with Independent Electrical & manual spring closing mechanism, Microprocessor release (EMI & EMC certified) for over current, earth fault & short circuit protection, Shunt trip coil 24V D.C / 220V A.C, Breaker Control Switch - 16A, Test terminal block set, circuits as per standard practice, auxiliary contactors with contacts (minimum 4NO+4NC) for positive interlocking of the breakers, necessary interlocking with PLC auto controls etc. as required including following accessories and suitable to receive bus duct/cable connections.

Metering, indications and protections for each incomer: a) LED indication lamps for RYB, breaker 'ON/ OFF/ TRIP', spring charged, DC control supply healthy etc with 2Amp control MCBs b) Set of Digital flush type multifunction meters (with RS485 port) 0- 1600A, class - 0.5 accuracy , showing V, A, PF, Hz, KW, KWH, etc. with 3 Nos. cast resin current transformers of 1600/5 Amp ratio, 15 VA Class 0.5 metering.(for DG ) b) Set of Digital flush type multifunction meters (with RS485 port) 0- 1600A, class - 0.5 accuracy , showing V, A, PF, Hz, KW, KWH, etc. with 3 Nos. cast resin current transformers of 1600/5 Amp ratio, 15 VA Class 0.5 metering.(for transformer) d) Under voltage/ Overvoltage with definite time relay & master trip relays - 1 set for Transformer incomer & Master trip relays - 1 set for DG incomer. e) Suitable size & nos of CT's for all protection relays (class 5P10, 15VA) & APFC Relay (class 0.5, 15VA) as per drawings f) Surge Protection Device of type 1+ 2 of 25KA. Bus Bar : TPN aluminium extensible type main bus bars of minimum of 2000 Amps. capacity & auxiliary Bus Bars of suitable capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 50ka capacity.

Outgoings: 1 No. - 800 Amp. 50ka three pole microprocessor release, MDO ACB (Ics=lcu=Icw) with O/L, S/C & earth fault protection. (Capacitor-1) 3 Nos. - 400 Amp. 50ka FP microprocessor release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection. (1 nos. Spare 3 Nos. - 315 Amp. 50ka FP microprocessor release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection. (1 nos. Spare 1 Nos. - 200 Amp. 50ka FP Thermal release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection. 3 Nos. - 160 Amp. 50ka FP Thermal release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection. (1 nos. Spare 1 Nos. - 125 Amp. 50ka FP Thermal release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection. 3 Nos. - 63 Amp. 50ka FP Thermal release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection. (1 nos. Spare) Each outgoing breaker shall have the following accessories- a) 1 No. - 96 sq.mm. flush pattern digital type multifunction meter (with RS485 port) showing V, A, PF, Hz, KW, KWH, KVAR, etc. with three nos. cast resin suitable rating of CT's, class 0.5 accuracy & 15 VA burden, protection MCB's etc. b) LED indication lamps with 2Amp back up control MCB for RYB, breaker 'ON/ OFF/ TRIP', spring charged, DC control supply healthy, test terminal block set, circuits as per standard practice etc. as required for all ACB's. c) Extended rotary operating mechanism, terminal extension spreaders, LED indication lamps with 2Amp control MCB for breaker 'ON/OFF' for all MCCB's. Bus Coupler 1 No. 2000 Amps, 50 KA, 440 volt 4-P EDO ACB without release complete with following: 6 Nos. NO/NC contacts for remote opening & closing Red/Green / Amber / ON/OFF / Trip indicating lamps with 2A SP MCB as backup protection. Backup MCB and terminal blocks as required. TNC Breaker Control switch Required Operation / Interlocking with other incomers & Bus Coupler to be provided as per Interlocking / operation scheme indicated in Drawing No. - Operation / Interlocking shall be through micro PLC.

Section- 2 Incomers: 1600 Amp. 4 Pole ACB - 1 set (For DG supply) 1600 Amp. 4 Pole ACB - 1 set (For Transformer supply) Air Circuit Breaker Horizontal drawout type of fault breaking capacity 50KA (Ics=lcu=Icw) Electrical Draw Out Motorized operated, fitted with interlocked door, automatic safety shutters, mechanical ON/OFF and service/ test/isolated position indicators and frame earthing contact, conforming to IS-13947-2 1993 as amended up-to-date complete with Independent Electrical & manual spring closing mechanism, Microprocessor release (EMI & EMC certified) for over current, earth fault & short circuit protection, Shunt trip coil 24V D.C / 220V A.C, Breaker Control Switch - 16A, Test terminal block set, circuits as per standard practice, auxiliary contactors with contacts (minimum 4NO+4NC) for positive interlocking of the breakers, necessary interlocking with PLC auto controls etc. as required including following accessories and suitable to receive bus duct/cable connections. Metering, indications and protections for each incomer: a) LED indication lamps for RYB, breaker 'ON/ OFF/ TRIP', spring charged, DC control supply healthy etc with 2Amp control MCBs b) Set of Digital flush type multifunction meters (with RS485 port) 0- 1600A, class - 0.5 accuracy , showing V, A, PF, Hz, KW, KWH, etc. with 3 Nos. cast resin current transformers of 1600/5 Amp ratio, 15 VA Class 0.5 metering.(for DG ) b) Set of Digital flush type multifunction meters (with RS485 port) 0- 1600A, class - 0.5 accuracy , showing V, A, PF, Hz, KW, KWH, etc. with 3 Nos. cast resin current transformers of 1600/5 Amp ratio, 15 VA Class 0.5 metering.(for transformer) d) Under voltage/ Overvoltage with definite time relay & master trip relays - 1 set for Transformer incomer & Master trip relays - 1 set for DG incomer. e) Suitable size & nos of CT's for all protection relays (class 5P10, 15VA) & APFC Relay (class 0.5, 15VA) as per drawings f) Surge Protection Device of type 1+ 2 of 25KA.

Bus Bar : TPN aluminium extensible type main bus bars of minimum of 2000 Amps. capacity & auxiliary Bus Bars of suitable capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 50ka capacity. Outgoings: 1 No. - 800 Amp. 50ka three pole microprocessor release, MDO ACB (Ics=lcu=Icw) with O/L, S/C & earth fault protection. (Capacitor-2) 4 Nos. - 400 Amp. 50ka FP microprocessor release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection. (1 nos. Spare 2 Nos. - 250 Amp. 50ka FP Thermal release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection. (1 nos. Spare 4 Nos. - 125 Amp. 50ka FP Thermal release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection. (1 nos. Spare 1 Nos. - 100 Amp. 50ka FP Thermal release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection. (1 nos. Spare) 5 Nos. - 63 Amp. 50ka FP Thermal release, MCCB (Ics=lcu) with O/L, S/C & modular earth fault protection. (1 nos. Spare) Each outgoing breaker shall have the following accessories- a) 1 No. - 96 sq.mm. flush pattern digital type multifunction meter (with RS485 port) showing V, A, PF, Hz, KW, KWH, KVAR, etc. and three nos. cast resin suitable rating of CT's, class 0.5 accuracy & 15 VA burden, protection MCB's etc. b) LED indication lamps with 2Amp back up control MCB for RYB, breaker 'ON/ OFF/ TRIP', spring charged, DC control supply healthy, test terminal block set, circuits as per standard practice etc. as required for all ACB's. c) Extended rotary operating mechanism, terminal extension spreaders, LED indication lamps with 2Amp control MCB for breaker 'ON/OFF' for all MCCB's.

16 Window annunciation panel (for each D.G. Set) for following indications/ alarms : Set fails to start Engine overheat. Excitation failure. High temperature Low Lube oil pressure. Over speed Low fuel oil level Cooling water flow failure Breaker Trip Generator fault. DC control supply failure. Voltage out of limits. Spares. Necessary interlocking/ controlling with PLC auto controls i/c PLC hardwares & software etc. complete as required. Main LT cum Synchronization panel described as above & as per drawing.

Busbar : TP aluminium extensible type main bus bars of minimum of 300 Amps. capacity & auxiliary Bus Bars of suitable capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete for cross section, size supports & their spacing etc. for withstanding fault level of 35ka capacity. Outgoings :- Control MCB/ MCCBs with capacitor banks: 125Amp. TP MCCB '35ka' Thermal Magnetic release having O/L & S/C protection with 50 KVAr, 415V (fixed) Heavy duty capacitor bank etc. - 1 set. 125Amp. TP MCCB '35ka' Thermal Magnetic release having O/L & S/C protection with 50 KVAr, 415V Heavy duty capacitor bank etc. - 3 set. 63Amp. TP MCCB '35ka' Thermal Magnetic release having O/L & S/C protection with 25 KVAr, 415 V Heavy duty capacitor bank, Capacitor Duty Contactor etc - 2 sets. 40Amp. TP MCCB '10ka' Thermal Magnetic release having O/L & S/C protection with 20 KVAr, 415 V Heavy duty capacitor bank, Capacitor Duty Contactor etc - 3 sets. 32Amp. TP MCB '10ka' Thermal Magnetic release having O/L & S/C protection with 10 KVAr, 415 V Heavy duty capacitor bank, Capacitor Duty Contactor etc - 2 sets. 25Amp. TP MCB '10ka' Thermal Magnetic release having O/L & S/C protection with 5 KVAr, 415 V Heavy duty capacitor bank, Capacitor Duty Contactor etc - 2 sets. Capacitor Panel as above

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 315 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 400 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 8 Nos. (3 No. Spare)63A 4P MCB '10kA' - 15 nos. (5 No. Spare) 32A 4P MCB '10kA' - 5 nos. (1 No. Spare) Panel describe as above

Lift Panel (2nos. Lift) Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing / wall mounted factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming i) 1 No. - 63 amps four pole MCCB (25 KA) with following accessories: a) 3 Nos. Phase indication LED lamps with 2Amp back up MCB, breaker 'ON/OFF' indicating light with 2A MCB b) Set of Digital flush type class 0.5 accuracy multifunction meter, showing V, A, PF, Hz, KW, KWH, KVAR, etc. and 3 Nos. cast resin current transformers of 63/ 5 Amp ratio, 15 VA Class 0.5 metering. Bus Bar : 4P aluminium extensible type main bus bars of minimum of 100 Amp capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete. Outgoings: 3 Nos. - 63 Amp. four pole (10kA) (1 Nos. Spare) 2 Nos. - 32 Amp. DP (10kA) MCB Each outgoing breaker shall have the following accessories- a) LED indication lamps with 2Amp back up control MCB for breaker 'ON/OFF' including terminal extension spreaders for all MCCB's. Lift Panel described as above

Girls Hostel-1 & 2/Dining Panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required.

Incoming: 1 No. of 315 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 400 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 8 Nos. (3 No. Spare) 63A 4P MCB '10kA' - 15 nos. (5 No. Spare) 32A 4P MCB '10kA' - 5 nos. (1 No. Spare) Panel describe as above

Lift Panel (2nos. Lift) Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing / wall mounted factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required.

Incoming i) 1 No. - 63 amps four pole MCCB (25 KA) with following accessories: a) 3 Nos. Phase indication LED lamps with 2Amp back up MCB, breaker 'ON/OFF' indicating light with 2A MCB b) Set of Digital flush type class 0.5 accuracy multifunction meter, showing V, A, PF, Hz, KW, KWH, KVAR, etc. and 3 Nos. cast resin current transformers of 63/ 5 Amp ratio, 15 VA Class 0.5 metering. Bus Bar : 4P aluminium extensible type main bus bars of minimum of 100 Amp capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete. Outgoings: 3 Nos. - 63 Amp. four pole (10kA) (1 Nos. Spare) 2 Nos. - 32 Amp. DP (10kA) MCB Each outgoing breaker shall have the following accessories- a) LED indication lamps with 2Amp back up control MCB for breaker 'ON/OFF' including terminal extension spreaders for all MCCB's. Lift Panel described as above

Jr. Resident Hostel panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 125 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 160 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 3 Nos. (1 No. Spare) 63A 4P MCB '10kA' - 6 nos. (2 No. Spare) Panel describe as above

Lift Panel (2nos. Lift) Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing / wall mounted factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming i) 1 No. - 63 amps four pole MCCB (25 KA) with following accessories: a) 3 Nos. Phase indication LED lamps with 2Amp back up MCB, breaker 'ON/OFF' indicating light with 2A MCB b) Set of Digital flush type class 0.5 accuracy multifunction meter, showing V, A, PF, Hz, KW, KWH, KVAR, etc. and 3 Nos. cast resin current transformers of 63/ 5 Amp ratio, 15 VA Class 0.5 metering. Bus Bar : 4P aluminium extensible type main bus bars of minimum of 100 Amp capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete. Outgoings: 3 Nos. - 63 Amp. four pole (10kA) (1 Nos. Spare) 2 Nos. - 32 Amp. DP (10kA) MCB Each outgoing breaker shall have the following accessories- a) LED indication lamps with 2Amp back up control MCB for breaker 'ON/OFF' including terminal extension spreaders for all MCCB's. Lift Panel described as above

Sr. Resident Hostel panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 160 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 200 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 3 Nos. (1 No. Spare) 63A 4P MCB '10kA' - 6 nos. (2 No. Spare) 63A DP MCB '10kA' - 1No. Spare Panel describe as above

Lift Panel (2nos. Lift) Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing / wall mounted factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming i) 1 No. - 63 amps four pole MCCB (25 KA) with following accessories: a) 3 Nos. Phase indication LED lamps with 2Amp back up MCB, breaker 'ON/OFF' indicating light with 2A MCB b) Set of Digital flush type class 0.5 accuracy multifunction meter, showing V, A, PF, Hz, KW, KWH, KVAR, etc. and 3 Nos. cast resin current transformers of 63/ 5 Amp ratio, 15 VA Class 0.5 metering. Bus Bar : 4P aluminium extensible type main bus bars of minimum of 100 Amp capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete. Outgoings: 3 Nos. - 63 Amp. four pole (10kA) (1 Nos. Spare) 2 Nos. - 32 Amp. DP (10kA) MCB Each outgoing breaker shall have the following accessories- a) LED indication lamps with 2Amp back up control MCB for breaker 'ON/OFF' including terminal extension spreaders for all MCCB's. Lift Panel described as above

Boys Intern Hostel panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 125 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 160 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 3 Nos. (1 No. Spare) 63A 4P MCB '10kA' - 6 nos. (2 No. Spare) 63A DP MCB '10kA' - 1No. Spare Panel describe as above

Lift Panel (2nos. Lift) Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing / wall mounted factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming i) 1 No. - 63 amps four pole MCCB (25 KA) with following accessories: a) 3 Nos. Phase indication LED lamps with 2Amp back up MCB, breaker 'ON/OFF' indicating light with 2A MCB b) Set of Digital flush type class 0.5 accuracy multifunction meter, showing V, A, PF, Hz, KW, KWH, KVAR, etc. and 3 Nos. cast resin current transformers of 63/ 5 Amp ratio, 15 VA Class 0.5 metering. Bus Bar : 4P aluminium extensible type main bus bars of minimum of 100 Amp capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete. Outgoings: 3 Nos. - 63 Amp. four pole (10kA) (1 Nos. Spare) 2 Nos. - 32 Amp. DP (10kA) MCB Each outgoing breaker shall have the following accessories- a) LED indication lamps with 2Amp back up control MCB for breaker 'ON/OFF' including terminal extension spreaders for all MCCB's. Lift Panel described as above

Girls Intern Hostel panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 125 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 160 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 160 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 3 Nos. (1 No. Spare) 63A 4P MCB '10kA' - 6 nos. (2 No. Spare) 63A DP MCB '10kA' - 1No. Spare Panel describe as above

Lift Panel (2nos. Lift) Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing / wall mounted factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming i) 1 No. - 63 amps four pole MCCB (25 KA) with following accessories: a) 3 Nos. Phase indication LED lamps with 2Amp back up MCB, breaker 'ON/OFF' indicating light with 2A MCB b) Set of Digital flush type class 0.5 accuracy multifunction meter, showing V, A, PF, Hz, KW, KWH, KVAR, etc. and 3 Nos. cast resin current transformers of 63/ 5 Amp ratio, 15 VA Class 0.5 metering. Bus Bar : 4P aluminium extensible type main bus bars of minimum of 100 Amp capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete. Outgoings: 3 Nos. - 63 Amp. four pole (10kA) (1 Nos. Spare) 2 Nos. - 32 Amp. DP (10kA) MCB Each outgoing breaker shall have the following accessories- a) LED indication lamps with 2Amp back up control MCB for breaker 'ON/OFF' including terminal extension spreaders for all MCCB's. Lift Panel described as above

Nurse Hostel panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 125 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. 1 No. of 125 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 160 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 3 Nos. (1 No. Spare) 63A 4P MCB '10kA' - 6 nos. (2 No. Spare) 63A DP MCB '10kA' - 1No. Spare Panel describe as above

Lift Panel (2nos. Lift) Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing / wall mounted factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming i) 1 No. - 63 amps four pole MCCB (25 KA) with following accessories: a) 3 Nos. Phase indication LED lamps with 2Amp back up MCB, breaker 'ON/OFF' indicating light with 2A MCB b) Set of Digital flush type class 0.5 accuracy multifunction meter, showing V, A, PF, Hz, KW, KWH, KVAR, etc. and 3 Nos. cast resin current transformers of 63/ 5 Amp ratio, 15 VA Class 0.5 metering. Bus Bar : 4P aluminium extensible type main bus bars of minimum of 100 Amp capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete. Outgoings: 3 Nos. - 63 Amp. four pole (10kA) (1 Nos. Spare) 2 Nos. - 32 Amp. DP (10kA) MCB Each outgoing breaker shall have the following accessories- a) LED indication lamps with 2Amp back up control MCB for breaker 'ON/OFF' including terminal extension spreaders for all MCCB's. Lift Panel described as above

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 200 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 250 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 6 Nos. (2 No. Spare) 63A 4P MCB '10kA' - 10 nos. (2 No. Spare) 63A DP MCB '10kA' - 2No. Spare Panel describe as above

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing / wall mounted factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming i) 1 No. - 63 amps four pole MCCB (25 KA) with following accessories: a) 3 Nos. Phase indication LED lamps with 2Amp back up MCB, breaker 'ON/OFF' indicating light with 2A MCB b) Set of Digital flush type class 0.5 accuracy multifunction meter, showing V, A, PF, Hz, KW, KWH, KVAR, etc. and 3 Nos. cast resin current transformers of 63/ 5 Amp ratio, 15 VA Class 0.5 metering. Bus Bar : 4P aluminium extensible type main bus bars of minimum of 100 Amp capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete. Outgoings: 3 Nos. - 63 Amp. four pole (10kA) (1 Nos. Spare) 2 Nos. - 32 Amp. DP (10kA) MCB Each outgoing breaker shall have the following accessories- a) LED indication lamps with 2Amp back up control MCB for breaker 'ON/OFF' including terminal extension spreaders for all MCCB's. Lift Panel described as above

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 400 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 500 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 3 Nos. (1 No. Spare) 63A 4P MCB '10kA' - 6 nos. (2 No. Spare) 63A DP MCB '10kA' - 1No. Spare Panel describe as above

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing / wall mounted factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming i) 1 No. - 63 amps four pole MCCB (25 KA) with following accessories: a) 3 Nos. Phase indication LED lamps with 2Amp back up MCB, breaker 'ON/OFF' indicating light with 2A MCB b) Set of Digital flush type class 0.5 accuracy multifunction meter, showing V, A, PF, Hz, KW, KWH, KVAR, etc. and 3 Nos. cast resin current transformers of 63/ 5 Amp ratio, 15 VA Class 0.5 metering. Bus Bar : 4P aluminium extensible type main bus bars of minimum of 100 Amp capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete. Outgoings: 3 Nos. - 63 Amp. four pole (10kA) (1 Nos. Spare) 2 Nos. - 32 Amp. DP (10kA) MCB Each outgoing breaker shall have the following accessories- a) LED indication lamps with 2Amp back up control MCB for breaker 'ON/OFF' including terminal extension spreaders for all MCCB's. Lift Panel described as above

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 63 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 100 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 4 Nos. (2 No. Spare) 63A 4P MCB '10kA' - 6 nos. (2 No. Spare) 63A DP MCB '10kA' - 2No. Spare Panel describe as above

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 400 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 500 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 250amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 2 Nos. (1 No. Spare) 100amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 1 No. Spare 63amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 5 Nos. (1 No. Spare) 63A FP MCB '10kA' - 1 No. Spare Panel describe as above

Light & power Academic Block Panel T-1 Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 250 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 315 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63A 4P MCCB '10kA' - 1 no. spare 63A 4P MCB '10kA' - 12 nos. (2 no. spare) Panel describe as above

Ups Panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 Nos. 63amps, 415V 4P MCCB '25ka' with overcurrent and short circuit TM release. 1 Set of three phase R,Y,B, ON indicating lamps, along with 2A SP MCB backup protection. Bus Bars: 100Amps including in different sections of the panel for connection to various outgoing feeders as per drawing. Outgoing: 63A 4P MCB '10kA' - 7 nos. (2 no. spare) 63A DP MCB '10kA' - 1 no. spare UPS Panel Described as above

Lift Panel (2nos. Lift) Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing / wall mounted factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming i) 1 No. - 63 amps four pole MCCB (25 KA) with following accessories: a) 3 Nos. Phase indication LED lamps with 2Amp back up MCB, breaker 'ON/OFF' indicating light with 2A MCB b) Set of Digital flush type class 0.5 accuracy multifunction meter, showing V, A, PF, Hz, KW, KWH, KVAR, etc. and 3 Nos. cast resin current transformers of 63/ 5 Amp ratio, 15 VA Class 0.5 metering.Bus Bar : 4P aluminium extensible type main bus bars of minimum of 100 Amp capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete. Outgoings: 3 Nos. - 63 Amp. four pole (10kA) (1 Nos. Spare) 2 Nos. - 32 Amp. DP (10kA) MCB (1 Nos. Spare) Each outgoing breaker shall have the following accessories- a) LED indication lamps with 2Amp back up control MCB for breaker 'ON/OFF' including terminal extension spreaders for all MCCB's. Lift Panel described as above

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 400 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 500 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 200amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 2 Nos. (1 No. Spare) 100amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 1 No. Spare 63amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 6 Nos. (1 No. Spare) 63A FP MCB '10kA' - 1 No. Spare Panel describe as above

Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 200 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 250 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63A 4P MCCB '10kA' - 1 no. spare 63A 4P MCB '10kA' - 17 nos. (2 no. spare) Panel describe as above

UPS Output Panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 Nos. 63amps, 415V 4P MCCB '25ka' with overcurrent and short circuit TM release. 1 Set of three phase R,Y,B, ON indicating lamps, along with 2A SP MCB backup protection. Bus Bars: 100Amps including in different sections of the panel for connection to various outgoing feeders as per drawing. Outgoing: 63A 4P MCB '10kA' - 6 nos. (2 no. spare) 63A DP MCB '10kA' - 1 no. spare UPS Panel Described as above

Lift Panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing / wall mounted factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming i) 1 No. - 63 amps four pole MCCB (25 KA) with following accessories: a) 3 Nos. Phase indication LED lamps with 2Amp back up MCB, breaker 'ON/OFF' indicating light with 2A MCB b) Set of Digital flush type class 0.5 accuracy multifunction meter, showing V, A, PF, Hz, KW, KWH, KVAR, etc. and 3 Nos. cast resin current transformers of 63/ 5 Amp ratio, 15 VA Class 0.5 metering. Bus Bar : 4P aluminium extensible type main bus bars of minimum of 100 Amp capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete. Outgoings: 3 Nos. - 63 Amp. four pole (10kA) (1 Nos. Spare) 2 Nos. - 32 Amp. DP (10kA) MCB (1 Nos. Spare) Each outgoing breaker shall have the following accessories- a) LED indication lamps with 2Amp back up control MCB for breaker 'ON/OFF' including terminal extension spreaders for all MCCB's. Lift Panel described as above

Academic Block Panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 250 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 315 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 160amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 2 Nos. (1 No. Spare) 100amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 1 No. Spare 63amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 5 Nos. (1 No. Spare) 63A FP MCB '10kA' - 2 Nos. (1 No. Spare) Panel describe as above

Light & power Academic Block Panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 160 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 200 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63A 4P MCCB '10kA' - 1 no. spare 63A 4P MCB '10kA' - 12 nos. (2 no. spare) Panel describe as above

UPS Output Panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 Nos. 63amps, 415V 4P MCCB '25ka' with overcurrent and short circuit TM release. 1 Set of three phase R,Y,B, ON indicating lamps, along with 2A SP MCB backup protection. Bus Bars: 100Amps including in different sections of the panel for connection to various outgoing feeders as per drawing. Outgoing: 63A 4P MCB '10kA' - 5 nos. (2 no. spare) 63A DP MCB '10kA' - 1 no. spare UPS Panel Described as above

Lift Panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing / wall mounted factory built sheet steel enclosed modular construction extendable panel, suitable for operatrion on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming i) 1 No. - 63 amps four pole MCCB (25 KA) with following accessories: a) 3 Nos. Phase indication LED lamps with 2Amp back up MCB, breaker 'ON/OFF' indicating light with 2A MCB b) Set of Digital flush type class 0.5 accuracy multifunction meter, showing V, A, PF, Hz, KW, KWH, KVAR, etc. and 3 Nos. cast resin current transformers of 63/ 5 Amp ratio, 15 VA Class 0.5 metering. Bus Bar : 4P aluminium extensible type main bus bars of minimum of 100 Amp capacity with heat shrinkable coloured sleeves and i/c DMC/SMC bus bars supports at required intervals complete. Outgoings: 3 Nos. - 63 Amp. four pole (10kA) (1 Nos. Spare) 2 Nos. - 32 Amp. DP (10kA) MCB (1 Nos. Spare) Each outgoing breaker shall have the following accessories- a) LED indication lamps with 2Amp back up control MCB for breaker 'ON/OFF' including terminal extension spreaders for all MCCB's. Lift Panel described as above

Mortuary Panel Supplying, Installation, Testing and Commissioning of dust, damp and vermin proof free floor standing factory built sheet steel enclosed modular construction extendable panel, suitable for operation on 415 + 10% volts, 50 Hz AC 3 phase 4 wire system fabricated out of suitable sized square tubular section and covered with 2.0mm thick CRCA sheet, hinged doors of 2mm thick CRCA sheet, duly painted complete with aluminium bus bars, interconnection with solid copper conductor wires / aluminium strips, neutral links, earth bus etc. necessary metering protections & indications and mounted with the following as per drawing and technical specifications attached etc. complete as required. Incoming: 1 No. of 100 Amp 4P MCCB of 25 kA (Ics=Icu) Breaking capacity thermal based release with On Indicating Lamp with 2A SP MCB back-up. Bus Bars: Electrolytic high conductivity aluminium three phase and neutral (full rated)busbars rated at 433V,50 Hz., 125 amps, 25kA, insulated with heat shrinkable coloured PVC sleeves & clip on shrouds for joints. Outgoing: 63amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 2 Nos. (1 No. Spare) 100amps, 415V 4P MCCB '25kA' with overcurrent and short circuit Thermal based release.- 1 No. Spare 63A DP MCB '10kA' - 1 No. Spare Panel describe as above

3½ core X 240 Sq.mm.

3½ core X 185 Sq.mm.

3½ core X 150 Sq.mm.

3½ core X 120 Sq.mm.

3½ core X 95 Sq.mm.

3½ core X 70 Sq.mm.

3½ core X 50 Sq.mm.

3½ core X 35 Sq.mm.

3 core X 10 Sq.mm

3 core X 6 Sq.mm

4 core X 25 Sq.mm

4 core X 16 Sq.mm

4 core X 10 Sq.mm

4 core X 6 Sq.mm

3 core X 6 Sq.mm

4 core X 6 Sq.mm

Supply, assembly and laying of under floor, height adjustable junction box, supplied completely with base and cover plate floor installation including cutting and chasing the floor/ or on surface, making good the same, placing in position and cleaning from inside complete etc. as required. 250 mm x 38 mm (3 compartment)

150 mm x 38 mm (2 compartment)

100 mm x 38 mm (2 compartment)

50 mm x 38 mm (1 compartment)

Providing, laying, fixing, connecting and testing of undernoted sizes of copper strip/ GI strip/ wire from earth electrode to equipment loop and earthing system, in trenches, on surfaces, along pole or along M.S. support, etc. including excavation where required for laying the copper strip/ GI strip and filling back complete, conforming to relevant IS and all as specified. GI strip 50mm x 6mm on surface or in recess etc.

50mm dia GI pipe 'B' under floors/ paving area's etc.

Providing and fixing 25 x 5 mm G.I. Strip in 40 mm dia. G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Supply and fixing in position 1000mm wide checkered rubber matting of 11KV grade as per electricity rules,with thickness not less than 12mm.

Supply and fixing in position the best quality H.T. Danger Notice plate of 250mm x 200mm made of mild steel atleast 2mm thick and vitreous enamelled, white on both sides and with inscription in signal red colour on front side written in English & Hindi as required.

Supplying and fixing of fire buckets 5 Nos.in each set of approved quality, red painted from outside and white from inside conforming to IS : 2546/1974 with additional handle at the bottom, filled with fine sand and fixed on an angle iron frame as per the requirement of local authorities.

150 mm dia ID

Supply, fixing, testing and commissioning of automatic Linear pneumatic Tube Detection based Novec 1230 System for Electrical Panels (Linear Pnuematic Heat Detection Tube Panel Protection System), consisting of the Mentioned components 4 Kg capacity Novec 1230 , DLP Assembly with automatic valve, push in connector for tube, 4Kg Novec 1230 gas , mounting bracket, End of Line adopter and low pressure switch for monitoring system activation.

Supplying, Installation, Testing and Commissioning of single spike air terminals of 10mm dia.of 1000mm length as required and as per site conditions. The air terminal shall be manufactured with aluminium. The terminal shall be provided with the two side wall clamp to mount the air terminal and as per site condition and shall meet the requirement of IEC 62561-2.

Supplying, Installation, Testing and Commissioning of Wall Conductor holder for holding 8 mm dia. round conductor (for RCC wall). The conductor holder should be installed at every 1 mtr. The conductor holder shall be made with SS clamp mounted on plastic base support & as per IEC 62561-4.

Supplying, Installation, Testing and Commissioning of Test Clamp to disconnect the down conductor from the earth termination network for regular checks of the earth termination resistance value. (with enclosure). It shall meet the requirements of IEC 62561-2.

Supplying, Installation, Testing and Commissioning of Lightning Strike counter Model: JMV 6D for counting thenumber of lightning strikes without any powersupply. The Counter should be mounted on the Down Conductor. The LightningCounter should be IP65 rated enclosure suitablefor external application.

Supplying, Installation, Testing and Commissioning of Earthing termination made of copper-bonded rod of 10 feet length,14.2 mm dia. (Minimum copper bonding shall be 0.25mm) as per IS 3043, IEEE-80, NBC 2016 along with Rod-to-Conductor connectors, Earth enhancement material some with resistivity of 0.12 ohm-mtr, and complying IEC 62561-7 and Pit Cover complying IEC 62561-5 and other accessories as required and as per specification and other applicable codes.

Supplying, Installation, Testing and Commissioning of Class B/Type I Single Phase Surge Protection Devices as per IEC 62305-4 and tested according to IEC 61643 – 11, DIN Rail mountable with Maximum Continuous Operating Voltage of 320 V and Voltage Protection Level of 1.3 kV (L-N). Response Time should be less than 100 ns (L-N & N-PE). The maximum impulse test current should be 65 kA (10/350 µs) per pole and 100 kA (10/350 µs) neutral to protective earth. The surge protection devices shall be enclosed in polycarbonate enclosure of IP 65 rating.

Supplying, Installation, Testing and Commissioning of Class C/Type II Single Phase Surge Protection Devices as per IEC 62305-4 and tested according to IEC 61643 – 11, DIN Rail mountable with Maximum Continuous Operating Voltage of 320 V and Voltage Protection Level of 1.3 kV (L-N). Response Time should be less than 25 ns per pole and less than 100 ns between neutral to protective earth. The maximum impulse discharge surge current should be 40 kA (8/20 µs) per pole and 60 kA (8/20 µs) neutral to protective earth. The surge protection devices shall be enclosed in polycarbonate enclosure of IP 65 rating.

SITC of LED Post Top : Body made of die cast aluminium fixture should have designed with a very small surface exposed to wind.fixture Diffuser in extra-clear tempered glass, resistant to thermal shocks and impacts,minimum system lumen package should be 5500-5600 lm at 6500k, CRI is 80, minimum ,System wattage should be maximum 40-44W LED: Power factor ≥0.9.Luminous flux maintenance 80%: 50.000h (L80B20).Beam should be Wide .Fixture voltage range would be100-300V/AC 50/60Hz,Fixture should have reputaed LED like lumiled, cree or Nichia.

SITC of LED Street light : in die-cast aluminium and designed with a very small surface exposed to wind. Cooling fins are integrated into the cover the heat dissipation system is specially designed and made to allow the operation of the LED lights with temperatures ensuring excellent performance/efficiency and durability.minimum system lumen package should be 6200-6300 lm at 6500k, CRI is 80, minimum ,System wattage should be maximum 50W , IP66, IK10LED: Power factor ≥0.9.Luminous flux maintenance 80%: 50.000h (L80B20).Beam should be Wide .Fixture voltage range would be100-300V/AC 50/60Hz,Fixture should have reputaed LED like lumiled, cree or Nichia

SITC of 4000 mm high hot dip GI step Pole. The bottom section of the pole not less than 114mm dia x2000mm long mm and Top Section of the Pole is of 89mm dia x 4000mm long Including bracket. The thickness of the pole sections shall be as per Medium class as per IS:1161. A service window with proper strengthening to cut out door shall be provided to accommodate a 6 amp SP MCB and 32 amp heavy duty connector for mains connections in the bottom part of the pole. The bottom part and the top part of the pole shall be joined together. flanges & shall be welded properly. Cast Aluminium embellishments shall be fitted and sealed by grub screw fixing. A mild steel base plate of 300 mm x300mm x15mm thick with stiffeners shall be welded at the bottom of the pole . The pole shall be hot dip galvanised after fabrication and duly pre treated and painted in U.V. ray resistant P.U. coating in approved colour shade.

SITC of 6000 mm high hot dip GI step Pole. The bottom section of the pole not less than 114mm dia x2000mm long mm and Top Section of the Pole is of 89mm dia x 4000mm long Including bracket. The thickness of the pole sections shall be as per Medium class as per IS:1161. A service window with proper strengthening to cut out door shall be provided to accommodate a 6 amp SP MCB and 32 amp heavy duty connector for mains connections in the bottom part of the pole. The bottom part and the top part of the pole shall be joined together. flanges & shall be welded properly. Cast Aluminium embellishments shall be fitted and sealed by grub screw fixing. A mild steel base plate of 300 mm x300mm x15mm thick with stiffeners shall be welded at the bottom of the pole . The pole shall be hot dip galvanised after fabrication and duly pre treated and painted in U.V. ray resistant P.U. coating in approved colour shade.

Supplying and drawing following sizes of PVC insulated PVC sheathed copper conductor unarmoured multicore cable in the existing poles and bracket from cable termination connector to the fitting i/c providing suitable copper lugs connections etc. as reqd. 3 core 1.5 sq.mm.

marked along with all accessories like socket, bend, couplers etc. conforming to IS 14930, Part II complete with fitting and cutting, jointing etc..direct in ground (75 cm below ground level) including excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required. 90 mm dia (OD-90 mm & ID-76 mm nominal)

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required. 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Supply, fixing, Wiring, testing & commissioning for Single Phase 20/25 Amp power plug outlets in seperate recessed zinc chromate passivated MS box with 4 sq.mm. FR insulated copper conductor wires alongwith 2.5 sq.mm. FR insulated copper conductor wire for loop earthing in concealed 2mm thick PVC conduits ( ISI marked) as called for including providing 6 pin modular socket outlet with box, ferrule numbering, etc. complete as required for Geyser.

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the wall and making good the same in case of recessed conduit as required. 20 mm

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 12 Way, Double Door

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/ Isolator) 4 way (4+12), Double door

6 way (4+18), Double door

8 way (4+24), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 12 way (4 + 36), Double door

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Single Pole

Supplying and fixing following rating, double pole, 240 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 40 amps

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required. 63 amps (30mA)

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. The rates shall include all components that may be required to make the supply and installation complete in all respects such as : All lamps Internal wiring between accessories Earthing terminal Complete provision for installation Suitable length of GI down rod, hanger and connecting wires where called for. Wires for connecting the fixtures to the point through connector block. All metal blocks to serve as base of fixtures Bonding with earth wires. Drilling holes in supports wherever required Fixing clamps, GI bolts and nuts, brass screws, saddles, rawl bolts and other fixing accessories as required. All recessed type fixture shall be considered with suitable length of flexible G.I. conduit. Testing of all fixtures & fans before and after installation.

Supply of lighting Fixturte Supply of the following lighting fixtures with all fixing accessories etc. as required. 11W LED Surface mounted light fixtures made of powder coated, elegantly designed pressure die-cast aluminium body with micro prismatic diffuser delivering UGR<19. P.F>0.95, THD<10%., Lumen>1100Lm, Efficacy is 110lm/w., Product Life 50000 Hr@L70. Digital Addressable Lighting Interface Dimmable.

12W LED Surface mounted light fixtures made of powder coated, elegantly designed pressure die-cast aluminium body with micro prismatic diffuser delivering UGR<19. P.F>0.95, THD<10%., Lumen>1300Lm, Efficacy is 110lm/w., Product Life 50000 Hr@L70. Digital Addressable Lighting Interface Dimmable.

15W LED Surface mounted light fixtures made of powder coated, elegantly designed pressure die-cast aluminium body with micro prismatic diffuser delivering UGR<19. P.F>0.95, THD<10%., Lumen>1600Lm, Efficacy is 110lm/w., Product Life 50000 Hr@L70. Digital Addressable Lighting Interface Dimmable.

20W LED linear surface / wall mounted 4ft light fixturMade of ultra slim co-extruded aluminium channel with housing part in white finish & diffuser part in reeded opal finish,. Lumen >2100, Efficacy is 110 lm/w Product Life 50000 Hr@L70.

20W LED linear surface / wall mounted 4ft light fixturMade of ultra slim co-extruded aluminium channel with housing part in white finish & diffuser part in reeded opal finish,. Lumen >2100, Efficacy is 110 lm/w Product Life 50000 Hr@L70.

30W LED recessed mounted 2 X 2 light fixtures made of CRCA powder coated white with micro prismatic diffuser delivering UGR<19. P.F>0.95, THD<10%.,High transmittance polystyrene opal diffuser .Lumen>3600, Efficacy is 120 lm/w, Product Life 50000 Hr@L70. Dimmable and with Sensor.

40W LED Surface mounted light fixtures made of powder coated, elegantly designed pressure die-cast aluminium body with micro prismatic diffuser delivering UGR<19. P.F>0.95, THD<10%., Lumen>4000Lm, Efficacy is 110lm/w., Product Life 50000 Hr@L70. Digital Addressable Lighting Interface Dimmable.

10W LED Foot light fixture amde of oval shaped pressure die-cast aluminium housing & ring for sturdiness & corrosion resistant,Epoxy powder coated white after phosphochromate treatment.High quality polycarbonate diffuser in opal finish. Lumen> 1000, Efficacy is >100 lm/w, IP66, IK 07.

10W BRACKET LIGHT Waterproof for outdoor lighting with 5 KV Surge Protection, CRI>80, pf> 0.9, 900 lumens complete with accessories

10W LED bulkhead light fixture amde of oval shaped pressure die-cast aluminium housing & ring for sturdiness & corrosion resistant,Epoxy powder coated white after phosphochromate treatment.High quality polycarbonate diffuser in opal finish. Lumen> 1000, Efficacy is >100 lm/w, IP65, IK 06.

10W LED linear surface / wall mounted 2ft light fixturMade of ultra slim co-extruded aluminium channel with housing part in white finish & diffuser part in reeded opal finish,. Lumen >1100, Efficacy is 110 lm/w Product Life 50000 Hr@L70.

Ceiling Fan- 1200MM

Ceiling Fan- 900MM

Ceiling Fan- 600MM

Exhaust Fan : 450 mm sweep

Installation, testing and commissioning of following pre-wired, LED fitting of all types, complete with all accessories and tube etc. directly on ceiling/ wall, including connection with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable and earthing etc. as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable etc. as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required. Upto 450 mm sweep

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of cable

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required. 2 Pair

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing co-axial TV cable RG-11 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface / recessed steel / PVC conduit as required.

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. TV antenna socket outlet

Telephone socket outlet

Socket for RJ 45 Jack for Cat - 6 Cable

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required. 1 or 2 Module (75mmX75mm)

Supply, erection, testing and commissioning of following tap off / splitter as per specification in 1.6mm thick CRCA sheet steel enclosure for CATV system. 4 way splitter box

Supplying, installation, testing and commissioning of online double conversion fully microprocessor based ,indoor type, compact UPS system with IGBT based PWM technology with inbuilt isolation transformer to achieve THD < 5% and input power factor of greater than 0.95 at 50% loading,suitable for Single phase AC input voltage 380 V to 450 V, 50 Hz +3% / - 3 % and single phase AC output voltage 415 ± 1% volts & frequency 50 ± 0.5 Hz , necessary VRLA batteries of suitable size having 30 minutes back up time and suitable size connecting cable (for UPS to Battery and battery to battery), static and maintenance bypass switch, SNMP card for RS232/ ethernet IP computability for operation and monitoring etc. with all components as mentioned in BOQ, specifications and schedule, complete etc. as required. Note : Concerning vendor needs to furnish the battery sizing calculations at the time of GA approval and battery size has to be as per the approved GA drawing. 10 KVA UPS with 30 min battery back up of 3 phase input & 3 phase output.

Supply, installation, testing & commissioning of UPS system comprising of 1 Nos. 7.5 kVA ( 1 Phase input & 1 Phase output) units . The UPS should be double conversion; online DSP Technology based IGBT Rectifier and inverter with 30 min backup. The UPS should have internally fitted with SNMP interface that will provide real time status information. The batteries should be sealed maintenance free The package shall include battery bank, stands, cables between UPS and battery bank, interconnecting links and related accessories as per specifications 7.5 kVA ( 1 Phase input & 1 Phase output) with 30 min backup

Supply, installation, testing & commissioning of UPS system comprising of 1 Nos. 7.5 kVA ( 1 Phase input & 1 Phase output) units . The UPS should be double conversion; online DSP Technology based IGBT Rectifier and inverter with 30 min backup. The UPS should have internally fitted with SNMP interface that will provide real time status information. The batteries should be sealed maintenance free The package shall include battery bank, stands, cables between UPS and battery bank, interconnecting links and related accessories as per specifications 7.5 kVA ( 1 Phase input & 1 Phase output) with 30 min backup

Suppplying, assembling, erecting, testing and commissioning of wall/ floor mounted Isolator box with enclosure and 1 No. 63 AMP, 4P MCCB.(MRI,CT SCAN)

Suppplying, assembling, erecting, testing and commissioning of wall/ floor mounted Isolator Box with enclosure and 1 No. 63 AMP, 4P MCB 10ka.(X-RAY,FLUOROSCOPY ROOM,PLASTIC SURGERY ROOM)

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required. (AC)

Supply of the following lighting fixtures with all fixing accessories etc. as required. 9W LED Surface mounted light fixtures made of powder coated, elegantly designed pressure die-cast aluminium body with micro prismatic diffuser delivering UGR<19. P.F>0.95, THD<10%., Lumen>1000Lm, Efficacy is 110lm/w., Product Life 50000 Hr@L70. Digital Addressable Lighting Interface Dimmable.

11W LED Surface mounted light fixtures made of powder coated, elegantly designed pressure die-cast aluminium body with micro prismatic diffuser delivering UGR<19. P.F>0.95, THD<10%., Lumen>1100Lm, Efficacy is 110lm/w., Product Life 50000 Hr@L70. Digital Addressable Lighting Interface Dimmable.

12W LED Surface mounted light fixtures made of powder coated, elegantly designed pressure die-cast aluminium body with micro prismatic diffuser delivering UGR<19. P.F>0.95, THD<10%., Lumen>1300Lm, Efficacy is 110lm/w., Product Life 50000 Hr@L70. Digital Addressable Lighting Interface Dimmable.

15W LED Surface mounted light fixtures made of powder coated, elegantly designed pressure die-cast aluminium body with micro prismatic diffuser delivering UGR<19. P.F>0.95, THD<10%., Lumen>1600Lm, Efficacy is 110lm/w., Product Life 50000 Hr@L70. Digital Addressable Lighting Interface Dimmable.

20W LED linear surface / wall mounted 4ft light fixturMade of ultra slim co-extruded aluminium channel with housing part in white finish & diffuser part in reeded opal finish,. Lumen >2100, Efficacy is 110 lm/w Product Life 50000 Hr@L70.

20W LED linear surface / wall mounted 4ft light fixturMade of ultra slim co-extruded aluminium channel with housing part in white finish & diffuser part in reeded opal finish,. Lumen >2100, Efficacy is 110 lm/w Product Life 50000 Hr@L70.

30W LED recessed mounted 2 X 2 light fixtures made of CRCA powder coated white with micro prismatic diffuser delivering UGR<19. P.F>0.95, THD<10%.,High transmittance polystyrene opal diffuser .Lumen>3600, Efficacy is 120 lm/w, Product Life 50000 Hr@L70. Dimmable and with Sensor.

40W LED Surface mounted light fixtures made of powder coated, elegantly designed pressure die-cast aluminium body with micro prismatic diffuser delivering UGR<19. P.F>0.95, THD<10%., Lumen>4000Lm, Efficacy is 110lm/w., Product Life 50000 Hr@L70. Digital Addressable Lighting Interface Dimmable.

10W LED Foot light fixture amde of oval shaped pressure die-cast aluminium housing & ring for sturdiness & corrosion resistant,Epoxy powder coated white after phosphochromate treatment.High quality polycarbonate diffuser in opal finish. Lumen> 1000, Efficacy is >100 lm/w, IP66, IK 07.

10W BRACKET LIGHT Waterproof for outdoor lighting with 5 KV Surge Protection, CRI>80, pf> 0.9, 900 lumens complete with accessories

10W LED bulkhead light fixture amde of oval shaped pressure die-cast aluminium housing & ring for sturdiness & corrosion resistant,Epoxy powder coated white after phosphochromate treatment.High quality polycarbonate diffuser in opal finish. Lumen> 1000, Efficacy is >100 lm/w, IP65, IK 06.

10W LED linear surface / wall mounted 2ft light fixturMade of ultra slim co-extruded aluminium channel with housing part in white finish & diffuser part in reeded opal finish,. Lumen >1100, Efficacy is 110 lm/w Product Life 50000 Hr@L70.

Ceiling Fan- 1200MM

Ceiling Fan- 900MM

Ceiling Fan- 600MM

Exhaust Fan : 450 mm sweep

Socket for RJ 45 Jack for Cat - 6 Cable

Supply, erection, testing and commissioning of following tap off / splitter as per specification in 1.6mm thick CRCA sheet steel enclosure for CATV system. 4 way splitter box

Supply, installation, testing & commissioning of UPS system comprising of 1 Nos. 3 kVA ( 1 Phase input & 1 Phase output) units . The UPS should be double conversion; online DSP Technology based IGBT Rectifier and inverter with 30 min backup. The UPS should have internally fitted with SNMP interface that will provide real time status information. The batteries should be sealed maintenance free The package shall include battery bank, stands, cables between UPS and battery bank, interconnecting links and related accessories as per specifications 3 kVA ( 1 Phase input & 1 Phase output) with 30 min backup

Supplying, installation, testing and commissioning of online double conversion fully microprocessor based ,indoor type, compact UPS system with IGBT based PWM technology with inbuilt isolation transformer to achieve THD < 5% and input power factor of greater than 0.95 at 50% loading,suitable for Single phase AC input voltage 380 V to 450 V, 50 Hz +3% / - 3 % and single phase AC output voltage 415 ± 1% volts & frequency 50 ± 0.5 Hz , necessary VRLA batteries of suitable size having 30 minutes back up time and suitable size connecting cable (for UPS to Battery and battery to battery), static and maintenance bypass switch, SNMP card for RS232/ ethernet IP computability for operation and monitoring etc. with all components as mentioned in BOQ, specifications and schedule, complete etc. as required. Note : Concerning vendor needs to furnish the battery sizing calculations at the time of GA approval and battery size has to be as per the approved GA drawing. 10 kVA ( 3 Phase input & 3 Phase output) with 30 min backup

Supplying, installation, testing and commissioning of online double conversion fully microprocessor based ,indoor type, compact UPS system with IGBT based PWM technology with inbuilt isolation transformer to achieve THD < 5% and input power factor of greater than 0.95 at 50% loading,suitable for Single phase AC input voltage 380 V to 450 V, 50 Hz +3% / - 3 % and single phase AC output voltage 415 ± 1% volts & frequency 50 ± 0.5 Hz , necessary VRLA batteries of suitable size having 30 minutes back up time and suitable size connecting cable (for UPS to Battery and battery to battery), static and maintenance bypass switch, SNMP card for RS232/ ethernet IP computability for operation and monitoring etc. with all components as mentioned in BOQ, specifications and schedule, complete etc. as required. Note : Concerning vendor needs to furnish the battery sizing calculations at the time of GA approval and battery size has to be as per the approved GA drawing. 15 kVA ( 3 Phase input & 3 Phase output) with 30 min backup

Suppplying, assembling, erecting, testing and commissioning of wall/ floor mounted Isolator box with enclosure and 1 No. 100 AMP, 4P MCCB of 25 KA.(BLOOD BANK)

DG SETS (HOSPITAL SITE) Supply, Installation, Erecting, testing and commissionig etc. of Silent Type Diesel Generating Set of 630 KVA, 3 phase & neutral, 50 c/s. 415 A.C. rating, comprising of Diesel Engine, Alternator, Acoustic enclosure conforming to latest environment protection requlations for emmission and noise levels as required and with other associated accessories including the cost of additional AVM pad as reuired. (A) DIESEL ENGINE: 1.Type: Multi-cylinder Air cooled Turbo charged with charge air cooling. 2. No. of strokes : 4 3. Fuelinjection :Direct 4. Maximum speed : 1500 RPM 5. Rated power : 380 BHP (minimum) 6. Cooling : Air cooled 7. Engine Starting : Battery starting. 8. Starting position : Universal. Auto/Manual (B) ALTERNATOR; Type : Brushless. Actual Power : 630 KVA at 50 deg C. Frequency : 50 Cycles/sec. Supply system :3 phases & neutral Connection : Star. Rated voltage: 415 Volts. Rated rpm. : 1500 rpm. max. Casing protection : As per IP-23 Insulation : Class `H'. Voltage : Automatic voltage regulator : regulator (Motorised) Power factor : 0.8. Controller : Type 3100 or similar (C) ACCESSORIES: The Diesel Engine shall be equipped with minimum following/ as indicated in the specifications, devices/ accessories built-in type including all standard fittings. Fuel supply pump with manual venting pump.

Radiator Turbo charger with air filter (dry/oil bath type) and damper. Charge air cooler. Suction fuel filter Lube oil filter. Hourmeter and RPM indicator. Battery Starting Mechanism. Instrument/Indication panel complete with the followings; a) Starting Switch with key. b) Lub. Oil Temp. gauge. c) Lub. Oil pressure gauge. d) Water Temp. gauge. Control devices for safety and monitoring alongwith indicators. (D) OTHER ACCESSORIES/EQUIPMENT Common base/foundation frame. Fly wheel and flexible coupling. Automatic voltage regulator (AVR). Lub oil filter. Fuel oil filter. AMF PANEL - Alternator shall have its AMF control panel consisting of followings 1 No. of 1000 Amp. Rating ACB, complete with relays/releases as required. necessary indications , metering , push buttons on/off switch. Battery charger complete with voltage regulator , Voltmeter and ammeter for charging the battery from external mains. Day storage tank for 750 ltr capacity fabricated out of 3mm thick MS sheet, with M.S. fuel pipe line, high & low level indicator and alarm contacts. Residential type silencer Anti vibration pads Necessary batterys ( minimum 1 of 180 AH capacity) with leads and mounting frame etc. The cost of initial charge of lubricants, coolant etc All the above housed in a suitable Sound attenuated enclouser as per specifications and required Diesel Generating set as described above.

1010 KVA DG Supply, transporting, loading, unloading, erecting, testing and commissionig etc. of Silent Type Diesel Generating Set of 1500 KVA, 3 phase & neutral, 50 c/s. 415 A.C. rating, comprising of following Diesel Engine, Alternator, Sound Attenuated Acoustic Enclosure, including necessary RCC foundation for errection including earth work as required and with other associated accessories: Diesel Engine Diesel engine 4 stroke Radiator cooled, electric start, of suitable BHP at 1500 RPM suitable for above output of alternator at 50 Degree C, 50%RH & at 1000 Meter MSL and conforming to BS 5514, BS 649, IS 10000, capable of taking 10% over loading for one hour included in 12 hours of continuous operation. The engine will be fitted complete with all the required accessories Engine mounted Instrument Panel fitted with and having digital display for following: Start-Stop switch with push button Water temperature indication Lubrication Oil pressure indication Battery charging indication RPM indication Over speed indication Engine Hours indication Digital electronic governor/digital voltage regulator Battery monitoring system & weak battery warning Digital metering for current, voltage, PF, KWH, KVA Alternator protection for under/over voltage, under/over frequency, reverse power, over current.

Alternator rated at 1010 KVA, 415 volts at 1500 RPM, 3 phase 50 HZ, AC supply with 0.8 lagging power factor at 50 Degree C, 50% RH & at 1000 Meter MSL. The alternator shall be having SPDP enclosure, brushless, continuous duty self excited and self-regulated through AVR conforming to IS :4722/BS 2613 suitable for tropical condition and ambient temperature at 50 Degree C and as per manufacturer's standard specifications with class-H insulation. Auto Start/Auto load management should be through controller type 3300 or approved equipment. with suitable Breaker Base Frame & Foundation: Both the engine and alternator shall be mounted on suitable base frame made of MS channel with necessary PCC block of 1:1.5:3 ratio of cement concrete of depth of 300 mm with suitable reinforcement which shall be installed on existing hard concrete floor and vibration isolation arrangement as per recommendation of manufacturer. Exhaust System: Dry exhaust manifold of suitable dia, welded blank MS pipe confirming to IS:3589 cut to required lengths (max. 2 mtrs) and installed with necessary bends, supports and clamps, anti-vibration mountings, insulation of exhaust system with 50mm thick mineral wool/Rockwool, wire mesh and aluminium cladding 0.8 mm thick etc. as required as per specifications with hospital exhaust silencer. Starting System: 24V DC Starting system comprising of starter motors: Voltage regulator and arrangement for initial excitation complete with suitable nos. of batteries (2 Nos. of 180 Amp. Hour capacity maintenance free ) as required as per specifications. Fuel Tank: Daily service fuel tank of 990 liters capacity fabricated out of 3 mm thick MS sheet complete with all standard accessories and fuel piping between fuel tank and diesel engine with MS Class C pipe of suitable dia complete with valves, level indication, flow switch with potential free contacts for giving signal to existing BMS system and accessories as required as per specifications. D.G Set Describe as above

ELECTRICAL LOW VOLTAGE (LV) SYSTEM Supply , Installtion , Testing and Comissioning of armoured 6 core Singlemode OFC cable for interfloor switches connectivity.

Supply , Installtion , Testing and Comissioning of 6 port loaded LIU with LC adaptor plates , pigtel cables etc complete as required.

Supply , Installtion , Testing and Comissioning of LC-LC singlemode fiber patch cord for LIU to switch connectivity.

Supply , Installation , Testing and commissioning of CAT 6 UTP cable 23 AWG solid copper conductors for Connectivity of Hub room to End Point.

Supply , Installtion , Testing and Comissioning of CAT6 information outlet (I/O) for Camera at user end.

Supply , Installtion , Testing and Comissioning of loaded 24 port CAT6 jack panel for CAT6 cable termination at rack end.

Supply , Installtion , Testing and Comissioning of loaded 16 port CAT6 jack panel for CAT6 cable termination at rack end.

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 3 feet for rack side switch to jack panel connectivity.

Supply , Installtion , Testing and Comissioning of CAT6 patch cord 7 feet for information outlet (I/O) to end user device connectivity.

Supply , Installtion , Testing and Comissioning of 1, 2 and 4 port face plate white for I/O fixing at user side.

Supply , Installtion , Testing and Comissioning of 15U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts.

Supply, Installation, Testing & Commissioning of fiber Modules 1000BASE

Supply, installation, testing and commissioning of 5 MP Dome camera , ONVIF profile S , G& T ,UL , CE , FCC Certified ,1/2.8” Progressive Scan CMOS ,2.7 mm to 12 mm motorized varifocal lens , Quad stream with each stream support H.265+ compression simultaneously ,min illumination : 0.01 Lux @ (F1.2,AGC ON), 0 Lux with IR , Shutter speed : 1 / 5s ~ 1 / 100,000 s ,120 dB WDR , Compression : H.265+ ,H.265 ,H.264+ H.264 .SD card support upto 128GB , Alarm trigger - 1 input / 1 output , frame rate : Main stream should support 25 fps@5MP ,Edge analytics : line crossing , perimeter intrusion ,Face detection(deep learning) , pedestrian detection ,cross counting , stationary object , In built IR LED , IR Distance upto 40 meters , IP 67 , IK10 ,POE.

Supply, installation, testing and commissioning of 5 MP Bullet camera , ONVIF profile S ,G & T . UL , CE , FCC Certified ,1/2.8” Progressive Scan CMOS ,2.7 mm to 12 mm motorized varifocal lens , Quad stream with each stream support H.265+ compression simultaneously ,min illumination : 0.01 Lux @ (F1.2,AGC ON), 0 Lux with IR , Shutter speed : 1 / 5s ~ 1 / 100,000 s ,120 dB WDR , Compression : H.265+ ,H.265 ,H.264+ H.264 .SD card support , Alarm trigger - 1 input / 1 output , frame rate : Main stream should support 25 fps@5MP , Edge analytics : line crossing , perimeter intrusion ,Face detection (deep learning) , pedestrian detection ,cross counting , stationary object , In built IR LED , IR Distance upto 50 meters , IP 67 , IK 10 housing , POE.

Supply, Installation, Testing and Commissioning of 24 port L2 Managed switch having port density 24 Nos. of 10M/100M/1G RJ45 Port POE/POE+ ports , 4 Nos. of 1G/10G SFP+ Port , 1X console port , Available POE power 370 W , 128 Gbps switching bandwidth , 32K MAC address support , Support L2 feature STP, RSTP ,MSTP . Support 802.1Q VLAN , port based VLAN , 4K VLAN entries , MAC based VLAN , IP subnet based VLAN . Support IEEE 802.3ad LACP . L3 features - static routing , DHCP server , Device Management system - topology view , floor view , map view , dashboard , traffic monitoring , cable diagnostics.CE,FCC certified

Supply, installation, testing & commissioning of manageable PoE+ Layer-2, 16 Port 4uplink port 10/100/1000 copper ports Base-T rack mounted switch, Web user, traffic manage HTTP/HTTPS web brows minimum IE5.5, Cat-6 RJ-45 connector supported, including 2 port 1G SFP module, maximum 75W power consumption. inbuilt fan, Storage temperature -200C-700C, Operating temperature 00C - 400C, Operating humidity 10% 90%, Complete with all rack mounting accessories for completion.

Supply, Installation, Testing & Commissioning of Addressable Photoelectric Smoke Detector with sensitivity range of 0.5 to 4.0% obs/ft. The detector shall have group decision technology for faster response & avoid false alarms. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user friendly rotary decimal switches. Designed to meet UL268, 7th Edition Below False Ceiling

Above False Ceiling

Supply, installing, testing and commissioning of Rise Heat Detector rated at 8.3 deg C/min. The detector shall have twin bi-colour LED for 360 deg viewing. Addressing shall be with user friendly rotary decimal switches.

Supply , Installation , Testing and Commissioning of Remote Indicator ( RI) High visibility LED, Wide viewing angle for increased visibility, Discreet design for incorporation in to any décor. RI should be of same make as detectors & devices.

Supply , Installation , Testing and Commissioning of Addressable Manual Call Point (Pull down / Break Glass Type). The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device.

Supply, Installation, Testing & Commissioning of Addressable Monitor Module for Sprinklers, Panic Bars & other Third Party Inputs. The monitor module shall monitor potential free contacts. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Supply, Installation, Testing & Commissioning of Addressable Control Module for Sounders / Strobes / Sounder cum Strobes. The control module shall provide supervised NAC output rated at 24v DC, 2A. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Supply, Installation, Testing & Commissioning of Isolator Module for Isolating short / dewired / loose circuits with automatic resetting arrangement. Isolator Base can also be proposed, however in that case needs to be considered with each detector & module. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Supply, installing, testing and commissioning of Addressable Relay Module for AHU, Access Control, Lifts, Staircase Pressurization, Fire Suppression & other Third Party Outputs. The relay module shall provide contact rated at 24v DC, 2A. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Supply , Installation , Testing and Commissioning of Sounder cum Strobe rated at 80 dBA @ 3m for Audible annunciation and 115cd flashintg at 1 Hz for visual indication. UL Listed.

Supply , Installation , Testing and Commissioning ofAddressable Fire Fighter's Telephone Jack with suitable supervised module for two way communication between Remote Fire Fighter & Fire Command Center. UL Listed.

Supply , Installation , Testing and Commissioning of Fire Fighter's Telephone Handset for two way communication between Remote Fire Fighter & Fire Command Center.

Supply, installing, testing and commissioning of 6W Ceiling Speaker with max SPL1M/1W 96dB . Frequency response of 80Hz-20KHz with a dispersion angle of 160 deg. The speaker should have tappings at 6W/3W/1.5W Ceiling Mounted Speakers

Supplying and Laying of 2 C X 1.5 Sq mm multi stranded twisted shielded FRLS Copper cable.

Supply , Installtion , Testing and Comissioning of armoured 6 core Singlemode OFC cable for interfloor switches connectivity.

Supply , Installtion , Testing and Comissioning of 6 port loaded LIU with LC adaptor plates , pigtel cables etc complete as required.

Supply , Installtion , Testing and Comissioning of 24 port loaded LIU for with LC adaptor plates , pigtel cables for core switch to access switch connectivity over fiber.

Supply , Installtion , Testing and Comissioning of LC-LC singlemode fiber patch cord for LIU to switch connectivity.

Supply , Installtion , Testing and Comissioning of loaded 24 port CAT6 jack panel for CAT6 cable termination at rack end.

Supply , Installtion , Testing and Comissioning of loaded 16 port CAT6 jack panel for CAT6 cable termination at rack end.

Supply , Installtion , Testing and Comissioning of 42 U (600W/1000D) floor mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts.

Supply , Installtion , Testing and Comissioning of 15U wall mount rack with fans , 2 cable managers , satationary shelf , 2 Nos. of hardware pkts.

Supply, Installation, Testing & Commissioning of Core Switch should have Min 24 x 1G Based SFP+ port , Min 1 x QSFP+ port , 2x Stacking port comprising 400 Gbps of stacking bandwidth from day 1 ,Min 2xQSFP28 Port from day1, Support less than 50 Millisecond convergence based of RFC 3619/REP/G.8032 , Min Operating temp 0-50 Degree C ,Must have Common criteriacertification EAL3/NDcPP/NDPP,CE.2 and CB certified.RPS Support . Min 850Gbps switching backplane ,Min 4GB RAM, 32GB Memory, Min 270K Mac address.Auto adustable fan based on temperture variation.

Supply, Installation, Testing & Commissioning of Appliance based customised ITAM for asset inventory management with ability to map physical locations and exact rack elevations for audit and support control. Appliance shall be Intel x86 based device with secure intranet server with Linux Based operating system and relational databases for long term storage. Appliance includes license for 100 units under control.

Supply, installation, testing and commissioning of 5 MP Dome camera , ONVIF profile S , G& T ,UL , CE , FCC Certified ,1/2.8” Progressive Scan CMOS ,2.7 mm to 12 mm motorized varifocal lens , Quad stream with each stream support H.265+ compression simultaneously ,min illumination : 0.01 Lux @ (F1.2,AGC ON), 0 Lux with IR , Shutter speed : 1 / 5s ~ 1 / 100,000 s ,120 dB WDR , Compression : H.265+ ,H.265 ,H.264+ H.264 .SD card support upto 128GB , Alarm trigger - 1 input / 1 output , frame rate : Main stream should support 25 fps@5MP ,Edge analytics : line crossing , perimeter intrusion ,Face detection(deep learning) , pedestrian detection ,cross counting , stationary object , In built IR LED , IR Distance upto 40 meters , IP 67 , IK10 ,POE.

Supply, installation, testing and commissioning of 5 MP Bullet camera , ONVIF profile S ,G & T . UL , CE , FCC Certified ,1/2.8” Progressive Scan CMOS ,2.7 mm to 12 mm motorized varifocal lens , Quad stream with each stream support H.265+ compression simultaneously ,min illumination : 0.01 Lux @ (F1.2,AGC ON), 0 Lux with IR , Shutter speed : 1 / 5s ~ 1 / 100,000 s ,120 dB WDR , Compression : H.265+ ,H.265 ,H.264+ H.264 .SD card support , Alarm trigger - 1 input / 1 output , frame rate : Main stream should support 25 fps@5MP , Edge analytics : line crossing , perimeter intrusion ,Face detection (deep learning) , pedestrian detection ,cross counting , stationary object , In built IR LED , IR Distance upto 50 meters , IP 67 , IK 10 housing , POE.

Supply, installation, testing and commissioning of 64 channel NVR , ONVIF compliant , recording bandwidth 640 Mbps , output interface 1 HDMI (up to 4K), 1 VGA , Alarm in/out :16ch in / 4ch out , 1 X RJ45 ethernet , iOS smartphone support , 8 HDD support , each HDD slot support upto 8 TB HDD , RAID support , 1x3.0 USB for backup /upgrade , 2x 2.0 USB for mouse .Edge analytics of poposed cameras must be integrated with NVR . Artificial Intelligence Support having face recognition with compatible deep learning supported cameras, AI-Face registered quantity upto 10,000 ,A.I maximum captured quantity 200,000. . UL,CE,FCC certified.

Supply, Installation, Testing & Commissioning of 8TB Surviellance Hard Disk.

Supply, Installation, Testing and Commissioning of Full HD 55" LED Professional Display Panel.

Supply, Installation, Testing and Commissioning of 24 port L2 Managed switch having port density 24 Nos. of 10M/100M/1G RJ45 Port POE/POE+ ports , 4 Nos. of 1G/10G SFP+ Port , 1X console port , Available POE power 370 W , 128 Gbps switching bandwidth , 32K MAC address support , Support L2 feature STP, RSTP ,MSTP . Support 802.1Q VLAN , port based VLAN , 4K VLAN entries , MAC based VLAN , IP subnet based VLAN . Support IEEE 802.3ad LACP . L3 features - static routing , DHCP server , Device Management system - topology view , floor view , map view , dashboard , traffic monitoring , cable diagnostics.CE,FCC certified

Supply, installation, testing & commissioning of manageable PoE+ Layer-2, 16 Port 4uplink port 10/100/1000 copper ports Base-T rack mounted switch, Web user, traffic manage HTTP/HTTPS web brows minimum IE5.5, Cat-6 RJ-45 connector supported, including 2 port 1G SFP module, maximum 75W power consumption. inbuilt fan, Storage temperature -200C-700C, Operating temperature 00C - 400C, Operating humidity 10% 90%, Complete with all rack mounting accessories for completion.

Supply, Installation, Testing and Commissioning of Workstation PC: Intel(R) Core(TM) i7-3770 Processor (8M Cache, up to 3.90 GHz); RAM: 8GB (1x8GB) Non-ECC DDR3 1600MHz ; Keyboard: 12 function keys; Chassis: Tower/Workstation; DVD: 8X Slimline DVD+/-RW, Data Only; Dual Graphics Card; Network interface card: Integrated Intel(R) 82579LM Gigabit1 Ethernet LAN 10/100/1000; Hard disk: 250GB, 7200 RPM 3.5" SATA 6Gb/s Hard Drive; Operating system: Windows 7 Professional 64 Bit or latest.

Supply , Installation , Testing and Commissioning of Addressable Beam Detector. The beam detector shall be used for High Ceiling application with a detection range upto 100 mtrs having 4 manual & 2 auto sensitivity settings. The beam detector shall be True addressable installed on the SLC circuite & communicate directly with the panel without any interface module.

Supply, Installation, Testing & Commissioning of Addressable Monitor Module for Sprinklers, Panic Bars & other Third Party Inputs. The monitor module shall monitor potential free contacts. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Supply, Installation, Testing & Commissioning of Addressable Control Module for Sounders / Strobes / Sounder cum Strobes. The control module shall provide supervised NAC output rated at 24v DC, 2A. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Supply, Installation, Testing & Commissioning of Isolator Module for Isolating short / dewired / loose circuits with automatic resetting arrangement. Isolator Base can also be proposed, however in that case needs to be considered with each detector & module. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Supply, installing, testing and commissioning of Addressable Relay Module for AHU, Access Control, Lifts, Staircase Pressurization, Fire Suppression & other Third Party Outputs. The relay module shall provide contact rated at 24v DC, 2A. The device shall have an LED which shall blink in normal state & get steady on activation to monitor the heath status of the device. Addressing shall be with user friendly rotary decimal switches. Module shall be supplied with mounting plate from OEM for ease of installation & maintenance.

Supply , Installation , Testing and Commissioning of Microprocessor based Multi-loop, True Peer-to-Peer Networkable Addressable Fire Alarm Control Panel with minimum 600 characters LCD display, 4000 event plus 1000 alarm log history events, QWERTY keypad for programming. The panel should be equipped with sufficient numbers of loops considering 20% spare capacity in each loop. Each loop shall have a capacity of minimum 300 analog addressable devices. The panel shall work in degrade mode in case of CPU failure, Products not having this feature may offer Redundant CPU. Four access levels, flash EPROM, 240 volts AC power supply, automatic battery charger, 24 volts sealed lead acid batteries sufficient for 24 hours normal working and 30 mins in alarm condition. The panel shall be complete with 2 ways Communication Fire Fighters System capable of supervising all the speaker circuits with adequate zone control and accessories. Failure of Fire Panel CPU shall not result in failure of DVC operation. The Fire Fighters Telephone System shall be capable of having minimum 30 Telephones in conference in multiple FFT Risers. Designed to meet UL864, 10th Edition 10 Loop

Supply , Installation , Testing and Commissioning of Network Repeater Panel with minimum 10" Color Touch Screen display with QWERTY Keypad, mapping minimum 2,00,000 points on network. The NRP shall act as an independent node communicating on the peer to peer network and shall not be dependant on the Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of NRP operation.

SITc of Graphics User Interface for Monitoring & Control of complete Fire, Voice Evacuation & Telephone Talkback System. The GUI based main network software shall network with other panels on True Peer-to-Peer network. It shall be capable of graphically representing each facility being monitored with floor plans and icons depicting the actual locations of the various systems, and / or sensors’ locations. It shall have the facility to change the sensitivity of any detector. The software shall be capable of monitoring 200 Nodes with 100 Mbps Transmission rate on Fibre Optics Network and 12 Mbps Transmission on cable and 2,50,000 network points. The software shall be capable to Monitor & Control all the Digital Voice Evactuation as well as 2 way communication from main control room using voice signals over Fire Network along with the Fire detection signal. The Graphic workstation shall act as an independent node communicating on the peer to peer network and shall not be dependant on the Fire Panel CPU for operation. Failure of Fire Panel CPU shall not result in failure of GUI.

Supply, installing, testing and commissioning of 8 zone IP based, digital Voice Alarm controller expandable upto 128 zones. The voice alarm controller should be able to connect directly over Ethernet. It should have functions like the audio playing, zone control, fault monitoring, log recording, volume control and amplifier switchover. The Voice alarm controller should also have the following functions: . 255 Priorities . Time schedule broadcasts . Its own PTT microphone . Capable of amplifier redundancy . 8 trigger inputs/outputs

Supply, installing, testing and commissioning of 1X500W Class-D Amplifier with 2 independent channels and can provide automatic re-settable overcurrent, overload, overheating, overvoltage, under-voltage and DC protection. 500 Watts

Supply , Installation , Testing and Commissioning of Graphics User Interface for Monitoring & Control of complete Fire alarm system. Features like Audio and visual alerts, Floor plan system visualisation, 3D idle/overview mode including mouse hover/click interaction, Sweeping animations, Programmable buttons and displays, Remote and multi-user access with defined credentials, Password and pin code protection, Network history view/search, Printable reports, Multi network supervision over TCP/IP. The GUI based main network software shall network with other panels on True Peer-to-Peer network. It shall be capable of graphically representing each facility being monitored with floor plans and icons depicting the actual locations of the various systems, and / or sensors’ locations. The Graphic workstation shall act as an independent node communicating on the peer to peer network.

HVAC WORKS VRF Outdoor Units Supply, Installation, Testing and Commissioning of Variable refrigerant flow/volume type air-condition system suitable to operate from 415 ± 10% volt, 50 Hz,3 phase AC power supply for cooling/heating with compressors (100% Inverter based) Hermetically sealed scroll type complete with fittings, AHU kit, isolator of suitable size in weather proof enclosure, vibration isolators with necessary wiring , connection & termination etc. including full charging of R-410A refrigerant gas complete as per requirement.Minimum COP shoud be 4.0 at full load at AHRI condition & All ODU machines should be treated with anti-Corrosion Treatment Adhesive at site. Note: Supply of The VRF Outdoor unit Floor supports consisting of a galvanized steel frame supported by adjustable leg and feet assemblies. The frame dimensions should be designed to take the weight with minimal deflection and should be manufactured from hot dip galvanized carbon steel. The feet dimensions shall be 200 mm / 305 mm / 450 mm square made from Nylon 6 B601L 30% glass fiber filled. These shall have mats underneath made from SBR-recycled rubber. The leg assembly should be adjustable up to 80 / 105 mm so that the frame can accommodate unevenness of the roof surface. Support Model : GP - MFS (MODULAR FRAMES) Side Discharge Units QWIK FOOT Spring Isolators for all the VRF Outddors. Foot Size 200x200 mm Strut cross bars 40x2.5mm Hotdip Galvanised C Channels. End Bars 40x40x3mm Hotdip Galvised Hollow Square bars . Note- Nominal capacity suitable for cooling requirements. Combination of following capacity's module: It Comprises of : 26 HP.

VRF Indoor Units Ceiling Suspended AHU Connected With VRF/VRV Outdoor Unit Supply, Installation, Testing & Commissioning of DX- type Ceiling Suspended air handling units of following capacity suitable to operate at 415+10% volt, 50 Hz, 3 phase AC power supply as specified and shown in drawings complete with the followings: EC Fan with canvas connection - double skin type made of 25 mm thick panels consisting of preplasticized G.I. casing of thickness 0.6 mm outside layer and 0.6 mm thick plane G.I inside layer with polyurethane foam (PUF) insulation of density 40+2 Kg/m3 factory injected between them by injection moulding machine. Electrostatic Communitated (EC) Backward curved centrifugal fan and Permanent Magnet, Brush Free or Brushless DC (BLDC), the EC motors utilize an electronic circuit-board to control the functionality of the motor.Motor and controller should be inbuilt part of fan and motor should be suitable for operating on 3 phase electric supply, 415+/-10% volts, 50 Hz cycles. EC motor should be operated with optentiometer for speed control DX coil section with aluminium finned copper tubes (tube thickness not less than 0.30mm) 6 row deep type cooling coil. The coil should be arranged to connect with multi circuits of outdoor units of required capacity. Pre filters with polarized media filter section with non wovensynthetic media down to 10 micron particle size with an efficiency of 90% ,space for fine Electrostatic filter air purification system that improves the indoor air quality through reducing harmful pollutants like particulate matter (PMx), PM 2.5, allergens, pollen, smoke, bacteria, pathogens based on Electrostatic precipitation technolog,It should be equivalent to MERV15 efficiency. UVGI Emitter system as per specifications along with power / control wiring and aluminium supporting structure. 20 G SS Drain pan, drain connection & U Traps. Complete in all respect including controls, supporting arrangement & complete in all respect as required, All AHU unit shall be coated with two component, polymeric coating with dry film thickness of about 25-35 microns on Cu and Upto 5 microns on Al fins & cooper Coil. The coating shall be strong, flexible and durable. It shall have good adhesion and abrasion resistance. It shall be resistant to moisture, UV, acid -alkali and other chemicals. The coating shall be applied using air assisted Spray gun or brush, at Site Note: all hanging support GRIPPLE guide line (SMACNA) TAG-CS AHU -1: 2200 CFM/ 4.0 TR, 50 mm SP with Mixing Box

Ceiling Suspended AHU Connected With VRF/VRV Outdoor Unit with laminar Flow and Hepa filter Supply, Installation, Testing & Commissioning of DX- type Ceiling Suspended air handling units of following capacity suitable to operate at 415+10% volt, 50 Hz, 3 phase AC power supply as specified and shown in drawings complete with the followings: EC Fan with canvas connection - double skin type made of 25 mm thick panels consisting of preplasticized G.I. casing of thickness 0.6 mm outside layer and 0.6 mm thick plane G.I inside layer with polyurethane foam (PUF) insulation of density 40+2 Kg/m3 factory injected between them by injection moulding machine. Electrostatic Communitated (EC) Backward curved centrifugal fan and Permanent Magnet, Brush Free or Brushless DC (BLDC), the EC motors utilize an electronic circuit-board to control the functionality of the motor.Motor and controller should be inbuilt part of fan and motor should be suitable for operating on 3 phase electric supply, 415+/-10% volts, 50 Hz cycles. EC motor should be operated with optentiometer for speed control DX coil section with aluminium finned copper tubes (tube thickness not less than 0.30mm) 6 row deep type cooling coil. The coil should be arranged to connect with multi circuits of outdoor units of required capacity. Pre filters with polarized media filter section with non wovensynthetic media down to 10 micron particle size with an efficiency of 90% ,space for fine Electrostatic filter air purification system that improves the indoor air quality through reducing harmful pollutants like particulate matter (PMx), PM 2.5, allergens, pollen, smoke, bacteria, pathogens based on Electrostatic precipitation technolog,It should be equivalent to MERV15 efficiency. Laminar Flow with HEPA filter UVGI Emitter system as per specifications along with power / control wiring and aluminium supporting structure. 20 G SS Drain pan, drain connection & U Traps. Complete in all respect including controls, supporting arrangement & complete in all respect as required, All AHU unit shall be coated with two component, polymeric coating with dry film thickness of about 25-35 microns on Cu and Upto 5 microns on Al fins & cooper Coil. The coating shall be strong, flexible and durable. It shall have good adhesion and abrasion resistance. It shall be resistant to moisture, UV, acid -alkali and other chemicals. The coating shall be applied using air assisted Spray gun or brush, at Site Note: all hanging support GRIPPLE guide line (SMACNA) TAG-CS AHU -1: 2000 CFM/ 3.5 TR, 50 mm SP with Mixing Box

4 Way Cassette Unit Supply, Installation, Testing and Commissioning of 4-way flow type Cassette Units of following capacity with fittings, remote controller,drain pump, panel, required power cable to connect indoor unit to socket etc. complete as required. 3.98 TR

Controller Supply, Installation, Testing and Commisioning of Main centralized touch screen type controller suitable for groups of indoor units to be installed for control.

Y-Joints Supply,Installation, Testing and Commissioning of Y-joints for various pipe sizes and headers etc.

Chemical Coating for HVAC Coils All interconnecting AHU Coils,Copper piping, joints, U bends and Aluminum fins within the condensing/ evaporator unit shall be coated with two component, polymeric coating with dry film thickness of about 25-35 microns on Cu and Upto 5 microns on Al fins & expose cooper pipe. The coating shall be strong, flexible and durable. It shall have good adhesion and abrasion resistance. It shall be resistant to moisture, UV, acid -alkali and other chemicals. The coating shall be applied using air assisted Spray gun or brush.

Drain Piping Supply, Installation and Testing in position the following UPVC condensate drain pipe (suitable for minimum 6kg/sq cm working pressure) insulated with 6 mm thick insulation as per required . 40 mm dia drain pipe

32 mm dia drain pipe

25 mm dia drain pipe

MULTI STAGE COOLING SYSTEM Double skin sandwich panel construction 25 mm thickness, PUF insulation of density 38-42 kg/cum in between, suitable for outdoor application-weather proof with inner skin 0. 6 mm thick PPGI (pre-painted galvanised iron ) and outer skin 0.6 mm thick PPGI. The entire framework shall be of extruded aluminium hollow profile and shall be mounted on galvanized steel channel. Drain pan shall be fabricated from 18 GSS construction as per manufacturer recommendation. The lifting brackets shall be provided on the unit base with lifting holes to captive in the framed extrusion. All panels shall be detachable or hinged. Hinges shall be made of die cast aluminium with stainless steel pivots, handles shall be made of hard nylon and be operational from both inside and outside of the unit. Units supplied with various sections shall be suitable for onsite assembly. Glass fibre reinforced nylon joints /corners shall be used to make self-supporting frame. All fixing and gaskets shall be concealed. Service doors shall be provided on both side of each section in order to provide user access to all unit components. Flexible fire retardant canvass connection shall be providing at the outlet of unit 4100 CFM,Static Pressure 75 mm WG

2500 CFM,Static Pressure 75 mm WG

DRY SCRUBBER Supply, Installation, Testing and Commissioning of dry Scrubber each comprising of electrostatic precipitation technology, dry type air cleaner to remove oil, smoke and fumes from exhaust air, as per the Specifications and as follows: Electrostatic section shall be made of 16 gauge galvanised sheet, high bake epoxy powder coated, washable type aluminium mesh filters, stainless steel spiked ionizers to create high voltage DC field, aluminum collector plates which should be alternatively charged positive and negative with large collecting area with 14" deep cell, to work as magnet for charged smoke and oil particles. Average efficiency of 90-95% in single pass as per ASHRAE test method. Electrostatic Precipitator should be able to charge particles from 0.01 micron to 10 microns through solid state power supply. Collector cell should be of permanent type and incorporate slide out facility for easy removal for cleaning. Power supplies shall be 100% solid state UL Listed, Module of capacity above 3000 CFM shall be equipped with Pulse width modulating (PWM)The system should be fitted with interlock switch for safety . The system should allow connection to a fan section to achieve 500 FPM velocity across the air cleaner 5100 CFM,Static Pressure 75 mm WG

3100 CFM,Static Pressure 75 mm WG

EXTRACT FAN SECTION Supply, Installation, Testing and Commissioning of exhuast SISW Backward curve fan & fan motor suitable for operation at 415 ± 10% V, 3 phase, 50 Hz AC with all necessary fixing supports, and arrangements and suitable capacity ofstarter panel & TP isolator with MS enclosure box with power cable (up to 10 Mtr) etc. 5100 CFM,Static Pressure 75 mm WG

3100 CFM,Static Pressure 75 mm WG

Air Curtain Supply, installation,testing and commisioning of air curtain (low noise type) operating on 230 volts,50hz supply with moving arrangements and infra red scanner for auto ON/OFF such that whenever that door is opened the air curtain is ON and when the doors are closed the air curatin is OFF, power connection from the nearest power point,etc, as required. Width 2.0 mtrs

Width 1.5 mtrs

Width 1.0 mtrs

Indoor Air Quality/ Air Purification Supply, installation, testing, commissioning, and handing over of a central air cleaning system with high filtration efficiency on PM2.5 combined with a high kill rate on airborne infectious diseases using Ultraviolet Germicidal Irradiation. The system shall be designed for providing protection from airborne infection and maintaining Indoor Air Quality in AHU unit with the following features and technical specifications. • The unit shall include activated carbon filtration and UV-C light that together eliminate harmful gases and airborne microbes, including bacteria, fungi, and viruses. • The system hasll meet EUROVENT ePM 1.0 80% requirement and ASHRAE guideline for UV-C application for SARS-CoV-2 inactivation. • The unit shall be Intertek ETL, UL 867, CSA C22 No. 187, and CE certified for safety and quality. • The system shall be tested on E. coli (ATCC 15597) in accordance with the standard ASTM E2149 with a kill rate of 99% in less than 15 minutes. • The system shall be designed in accordance with Chapter 62 Ultraviolet Air and Surface Treatment, 2019 ASHRAE Handbook. • The system shall be ANSI/ASHRAE 52.2 2017 tested with at least a MERV 15 rating and an ISO 16890 ePM 1.0 90% rating by an accredited lab. • The assembly shall include a UL 60730 certified run hour meter with inbuilt timer and maintenance tracking system. • The system should have a UL certified inbuilt pneumatic sensor allowing it to work as a controller. It must automatically detect airflow and the capability to interface with the building management system. If the HVAC system is turned ON and the airflow is detected, then the output power should be available to the system, otherwise the system shall automatically turn off for the protection of service personnel. TAG-CS AHU -1: 2200 CFM/ 4.0 TR

TAG-CS AHU -1: 2000 CFM/ 3.5 TR

4 Way Cassette Unit 3.98 TR

UVGI(Contamination Control Unit) SITC of upper room UVGI for reducing the infectious diseases like bacteria, virus and other pathogens. It should be specially designed to have a 254nm UV tube with 30W UV lamp power for every 200 sq. Ft. Of floor area. The unit should be designed with a intensity of 10uW/Cm2 with a kill rate of 99%. It should be installed at a hieght of 2.3 meters above the floor.

HEPA FILTER Supply, installation, testing and commissioning of epoxy sealed DOP tested HEPA filters of efficiency 99.97% down to 0.3 micron particle size in aluminium frame as per given drawings, specification and schedules. The cost shall include the cost and installation of HEPA filter in extruded Aluminium housing. 610x610x305

4800 CFM at 25 mm static pressure

4500 CFM at 25 mm static pressure

4200 CFM at 25 mm static pressure

3600 CFM at 25 mm static pressure

3300 CFM at 25 mm static pressure

2200 CFM at 25 mm static pressure

2000 CFM at 25 mm static pressure

1800 CFM at 25 mm static pressure

1400 CFM at 25 mm static pressure

1200 CFM at 25 mm static pressure

1000 CFM at 25 mm static pressure

500 CFM at 25 mm static pressure

4800 CFM at 25 mm static pressure

4500 CFM at 25 mm static pressure

4200 CFM at 25 mm static pressure

3600 CFM at 25 mm static pressure

3300 CFM at 25 mm static pressure

2200 CFM at 25 mm static pressure

2000 CFM at 25 mm static pressure

1800 CFM at 25 mm static pressure

1400 CFM at 25 mm static pressure

1200 CFM at 25 mm static pressure

1000 CFM at 25 mm static pressure

500 CFM at 25 mm static pressure

INLINE FAN Supply , installation , testing and commissoning , of duct mounted inline fans complete with direct driven centrifugal fan , TEFC squirrel cage induction motor , with efficiency class IE-3 , direct drive arrangement , heavy gauge sheet metal casing , rubber isolator mounts and other accessories.The fan shall be complete in all respect and should match the specification ,Drawings and Schedule. Inline fans shall be of following capacities. 1000 CFM Total static pressure of 20 mm WG

900 CFM Total static pressure of 15 mm WG

800 CFM Total static pressure of 10 mm WG

700 CFM Total static pressure of 10 mm WG

500 CFM Total static pressure of 10 mm WG

400 CFM Total static pressure of 10 mm WG

350 CFM Total static pressure of 10 mm WG

PROPELLER FAN Supply, installation, testing and commissioning of propeller fan with Al./SS blades and complete with induction Motor suitable for operation with 230 V single phase 50 Hz with suitable frame etc. as per IS:2312-1967 with gravity dampers for exhaust complete as per specifications and drawings.The quoted price shall consist of mounting arrangemnt for the fan. The maximum sound level of unit shall be 40dB(A) @ 3 m from source. 100 DIA

GSS DUCT (FACTORY FABRICATED) Supplying, installing, testing and balancing of Galvanised Steel Sheet (Completely Factory Fabricated with TDF/Slip ON Flanges) 120 GSM seamed ducting of following thickness including necessary supports (also of galvanised steel-I), hangers, nuts, bolts, gaskets, splitter dampers, turning vanes, canvas connections, connection pieces of rectangular to Spiral etc. complete as per technical specifications. All archs shall have baffles inside. The bidder shall quote his rates considering elbows, reducers, tees, baffles etc. The thickness of ducting shall be according to IS 655- 1963. Support/Gaskets shall be provided striclty as per the technical specifications, drawings. Support shall be considered at an interval of 2.5 mtrs and on all branches. For all main ducts engraved labels shall be provided as per reqmt of EIC. Measurement shall be made based upon effective duct area, Contractor to bid accordingly. Note: all hanging support GRIPPLE guide line (SMACNA) 24 G (0.63 mm)

GSS DUCT (SITE FABRICATED) Supply, fabrication on site and erection of following gauges of G.I sheet metal 175GSM ducting as per class VIII confirming to IS 277-1962(Revised) complete with elbows spliters, supports/suspenders bends, tees, vanes, double canvas connections, supports as per above mentioned specification for Factory fabricated duct complete in all respects as required. The thickness of the duct shall be confirmed to IS 655- 1963 Note: all hanging support GRIPPLE guide line (SMACNA) 24 G (0.63 mm)

VOLUME CONTROL DAMPER Supplying, installing, testing & commissioning of GI volume control damper with minimum 1.6 mm flange and 1.8 mm blade thickness within ducts to be provided with suitable links, levers and quadrants for manual control of volume of air flow and for proper balancing of the air distribution system as per schedules & drawings.

Supply, installation, testing,balancing and fixing of Powder coated aluminium extruded grill with aluminium construction collar damper for supply air as per specification & the sizes will be as per schedules and drawing.Refer technical specification for detail description

RETURN AIR GRILL Supply, installation, testing ,balancing and fixing of Powder coated aluminium extruded grill for return air as per specification & the sizes will be as per schedules and drawing.Refer technical specification for detail description

Supply, installation, testing,balancing and fixing of Powder coated aluminium extruded grill with collar damper for supply air as per specification & the sizes will be as per schedules and drawing.Refer technical specification for detail description

RETURN AIR DIFFUSER Supply, installation, testing ,balancing and fixing of Powder coated aluminium extruded grill for return air as per specification & the sizes will be as per schedules and drawing.Refer technical specification for detail description

Supply, installation, testing and commissioning of aluminium insulated flexible duct to connect the diffuser .It shall be as per specification & the sizes will be as per drawings and schedules : 200 mm Dia

Supplying, Installing, testing and commissioning of powder coated extruded aluminium exhaust air grille with min.60 % free area, with metallic frame work & fixing accessories, to be fixed on external wall to exhaust air from basement area to ambient , it shall be suitable for exhausting required air in CFM . Louvers need to be suitable in order avoid rain water entry in to basement @ 15 degree deflection with bird screen complete as per specification approved drawings and schedules.

Supplying, installing, testing and commissioning of GI construction fresh air louvers with min. 60 % free area, bird screen and painted in baked enamel shade as per clients or architect approval with metallic frame work complete as per specification approved drawings and schedules.

Supplying, installing, testing and commissioning of GI construction fresh/exhaust air louvers with min. 60 % free area, bird screen and painted in baked enamel shade as per clients or architect approval with metallic frame work complete as per specification approved drawings and schedules.

Supplying, Fixing,testing and commissioning of fire damper in supply air duct/main branch and return air path as and where required of required sizes i/c control wiring, the damper shall be motorized and spring return so as to close the damper in the event of power failure automatically and open the same in case of power being restored. The spring return action shall be inbuilt mechanism and not externally mounted. the damper shall also be closed in the event of fire signal complete as required and as per specifications. Fire damper

Actuator

Supply, installation, testing and commissioning of motorised(ON-OFF Type)duct mounted G.I volume control damper with enthalpy sensor and necessary control wiring (minimum 1.5 mm ) for integeration within AHU room.The unit shall be capable to communicate with BMS system Damper

Actuator

Supply ,Installation,testing and commissioning of duct acoustic lining of supply air duct and plenum with 15 mm thick Open Cell engineered Nitrile Rubber foam of density 140-180 kg/cu.m with in built Microban and tested as per ISO 354:2003 complete as required and as per specifications. 15 mm thick

Supply,Installation,testing and commissioning of double Layer canvas connection fire retardant cloth for the end connection of AHU/CSU/AIR WASHER/SCRUBBER/TFA and Ventilation fan to reduce the vibration.It shall be fire rated for atleat 2 hrs.Refer tender specification for detail description

The duct in internal areas shall be insulated as specified and the insulated duct/pipe shall be coated by Fevicol AC Duct King Lag coating for protection against Mechanical damage, Fungal growth, Flame spread, Water Permeance. The coating shall confirm UL723 for surface burning characteristics. The coating should comply the complete specification. 19 mm on Supply/Return duct

The duct in exposed area shall be insulated as specified and the insulated duct/pipe shall be coated with Fevicol Weather Protekt Coat for protection against Mechanical damage, Water Permeance Fungal growth, Flame spread, and Weathering Reistance. The product should comply complete specification. 19 mm on Supply/Return duct

Supply, Installation, testing and commissioning of control cum transmission wiring of 2 core x 1.5 sqmm copper in suitable PVC Conduits between indoor and outdoors unit.

VRF Outdoor Units Supply, Installation, Testing and Commissioning of Variable refrigerant flow/volume type air-condition system suitable to operate from 415 ± 10% volt, 50 Hz,3 phase AC power supply for cooling/heating with compressors (100% Inverter based) Hermetically sealed scroll type complete with fittings, AHU kit, isolator of suitable size in weather proof enclosure, vibration isolators with necessary wiring , connection & termination etc. including full charging of R-410A refrigerant gas complete as per requirement.Minimum COP shoud be 4.0 at full load at AHRI condition & All ODU machines should be treated with anti-Corrosion Treatment Adhesive at site. Note: Supply of The VRF Outdoor unit Floor supports consisting of a galvanized steel frame supported by adjustable leg and feet assemblies. The frame dimensions should be designed to take the weight with minimal deflection and should be manufactured from hot dip galvanized carbon steel. The feet dimensions shall be 200 mm / 305 mm / 450 mm square made from Nylon 6 B601L 30% glass fiber filled. These shall have mats underneath made from SBR-recycled rubber. The leg assembly should be adjustable up to 80 / 105 mm so that the frame can accommodate unevenness of the roof surface. Support Model : GP - MFS (MODULAR FRAMES) Side Discharge Units QWIK FOOT Spring Isolators for all the VRF Outddors. Foot Size 200x200 mm Strut cross bars 40x2.5mm Hotdip Galvanised C Channels. End Bars 40x40x3mm Hotdip Galvised Hollow Square bars . Note- Nominal capacity suitable for cooling requirements. Combination of following capacity's module: It Comprises of : 12 HP.

VRF Indoor Units Ceiling Suspended AHU Connected With VRF/VRV Outdoor Unit Supply, Installation, Testing & Commissioning of DX- type Ceiling Suspended air handling units of following capacity suitable to operate at 415+10% volt, 50 Hz, 3 phase AC power supply as specified and shown in drawings complete with the followings: EC Fan with canvas connection - double skin type made of 25 mm thick panels consisting of preplasticized G.I. casing of thickness 0.6 mm outside layer and 0.6 mm thick plane G.I inside layer with polyurethane foam (PUF) insulation of density 40+2 Kg/m3 factory injected between them by injection moulding machine. Electrostatic Communitated (EC) Backward curved centrifugal fan and Permanent Magnet, Brush Free or Brushless DC (BLDC), the EC motors utilize an electronic circuit-board to control the functionality of the motor.Motor and controller should be inbuilt part of fan and motor should be suitable for operating on 3 phase electric supply, 415+/-10% volts, 50 Hz cycles. EC motor should be operated with optentiometer for speed control DX coil section with aluminium finned copper tubes (tube thickness not less than 0.30mm) 6 row deep type cooling coil. The coil should be arranged to connect with multi circuits of outdoor units of required capacity. Pre filters with polarized media filter section with non wovensynthetic media down to 10 micron particle size with an efficiency of 90% ,space for fine Electrostatic filter air purification system that improves the indoor air quality through reducing harmful pollutants like particulate matter (PMx), PM 2.5, allergens, pollen, smoke, bacteria, pathogens based on Electrostatic precipitation technolog,It should be equivalent to MERV15 efficiency. UVGI Emitter system as per specifications along with power / control wiring and aluminium supporting structure. 20 G SS Drain pan, drain connection & U Traps. Complete in all respect including controls, supporting arrangement & complete in all respect as required, All AHU unit shall be coated with two component, polymeric coating with dry film thickness of about 25-35 microns on Cu and Upto 5 microns on Al fins & cooper Coil. The coating shall be strong, flexible and durable. It shall have good adhesion and abrasion resistance. It shall be resistant to moisture, UV, acid -alkali and other chemicals. The coating shall be applied using air assisted Spray gun or brush, at Site Note: all hanging support GRIPPLE guide line (SMACNA) TAG-CS AHU -1: 3600 CFM/ 8 TR, 50 mm SP with Mixing Box

4 Way Cassette Unit Supply, Installation, Testing and Commissioning of 4-way flow type Cassette Units of following capacity with fittings, remote controller,drain pump, panel, required power cable to connect indoor unit to socket etc. complete as required. 3.18 TR

Controller Supply, Installation, Testing and Commisioning of Main centralized touch screen type controller suitable for groups of indoor units to be installed for control.

Y-Joints Supply,Installation, Testing and Commissioning of Y-joints for various pipe sizes and headers etc.

Chemical Coating for HVAC Coils All interconnecting AHU Coils,Copper piping, joints, U bends and Aluminum fins within the condensing/ evaporator unit shall be coated with two component, polymeric coating with dry film thickness of about 25-35 microns on Cu and Upto 5 microns on Al fins & expose cooper pipe. The coating shall be strong, flexible and durable. It shall have good adhesion and abrasion resistance. It shall be resistant to moisture, UV, acid -alkali and other chemicals. The coating shall be applied using air assisted Spray gun or brush.

Drain Piping Supply, Installation and Testing in position the following UPVC condensate drain pipe (suitable for minimum 6kg/sq cm working pressure) insulated with 6 mm thick insulation as per required . 40 mm dia drain pipe

32 mm dia drain pipe

25 mm dia drain pipe

Air Curtain Supply, installation,testing and commisioning of air curtain (low noise type) operating on 230 volts,50hz supply with moving arrangements and infra red scanner for auto ON/OFF such that whenever that door is opened the air curtain is ON and when the doors are closed the air curatin is OFF, power connection from the nearest power point,etc, as required. Width 2.0 mtrs

Width 1.5 mtrs

Width 1.0 mtrs

Indoor Air Quality/ Air PurificationSupply, installation, testing, commissioning, and handing over of a central air cleaning system with high filtration efficiency on PM2.5 combined with a high kill rate on airborne infectious diseases using Ultraviolet Germicidal Irradiation. The system shall be designed for providing protection from airborne infection and maintaining Indoor Air Quality in AHU unit with the following features and technical specifications. • The unit shall include activated carbon filtration and UV-C light that together eliminate harmful gases and airborne microbes, including bacteria, fungi, and viruses. • The system hasll meet EUROVENT ePM 1.0 80% requirement and ASHRAE guideline for UV-C application for SARS-CoV-2 inactivation. • The unit shall be Intertek ETL, UL 867, CSA C22 No. 187, and CE certified for safety and quality. • The system shall be tested on E. coli (ATCC 15597) in accordance with the standard ASTM E2149 with a kill rate of 99% in less than 15 minutes. • The system shall be designed in accordance with Chapter 62 Ultraviolet Air and Surface Treatment, 2019 ASHRAE Handbook. • The system shall be ANSI/ASHRAE 52.2 2017 tested with at least a MERV 15 rating and an ISO 16890 ePM 1.0 90% rating by an accredited lab. • The assembly shall include a UL 60730 certified run hour meter with inbuilt timer and maintenance tracking system. • The system should have a UL certified inbuilt pneumatic sensor allowing it to work as a controller. It must automatically detect airflow and the capability to interface with the building management system. If the HVAC system is turned ON and the airflow is detected, then the output power should be available to the system, otherwise the system shall automatically turn off for the protection of service personnel. TAG-CS AHU -1: 3600 CFM/ 8 TR,

4 Way Cassette Unit 3.18 TR

UVGI(Contamination Control Unit) SITC of upper room UVGI for reducing the infectious diseases like bacteria, virus and other pathogens. It should be specially designed to have a 254nm UV tube with 30W UV lamp power for every 200 sq. Ft. Of floor area. The unit should be designed with a intensity of 10uW/Cm2 with a kill rate of 99%. It should be installed at a hieght of 2.3 meters above the floor.

10000 CFM at 25 mm static pressure

8500 CFM at 25 mm static pressure

7200 CFM at 25 mm static pressure

6300 CFM at 25 mm static pressure

6000 CFM at 25 mm static pressure

4500 CFM at 25 mm static pressure

4200 CFM at 25 mm static pressure

3800 CFM at 25 mm static pressure

3600 CFM at 25 mm static pressure

3300 CFM at 25 mm static pressure

2700 CFM at 25 mm static pressure

2200 CFM at 25 mm static pressure

1800 CFM at 25 mm static pressure

1300 CFM at 25 mm static pressure

1000 CFM at 25 mm static pressure

500 CFM at 25 mm static pressure

10000 CFM at 25 mm static pressure

8500 CFM at 25 mm static pressure

7200 CFM at 25 mm static pressure

6300 CFM at 25 mm static pressure

6000 CFM at 25 mm static pressure

4500 CFM at 25 mm static pressure

4200 CFM at 25 mm static pressure

3800 CFM at 25 mm static pressure

3600 CFM at 25 mm static pressure

3300 CFM at 25 mm static pressure

2700 CFM at 25 mm static pressure

2200 CFM at 25 mm static pressure

1800 CFM at 25 mm static pressure

1300 CFM at 25 mm static pressure

1000 CFM at 25 mm static pressure

500 CFM at 25 mm static pressure

INLINE FAN Supply , installation , testing and commissoning , of duct mounted inline fans complete with direct driven centrifugal fan , TEFC squirrel cage induction motor , with efficiency class IE-3 , direct drive arrangement , heavy gauge sheet metal casing , rubber isolator mounts and other accessories.The fan shall be complete in all respect and should match the specification ,Drawings and Schedule. Inline fans shall be of following capacities. 700 CFM Total static pressure of 10 mm WG

400 CFM Total static pressure of 10 mm WG

300 CFM Total static pressure of 10 mm WG

200 CFM Total static pressure of 10 mm WG

150 CFM Total static pressure of 10 mm WG

100 CFM Total static pressure of 10 mm WG

PROPELLER FAN Supply, installation, testing and commissioning of propeller fan with Al./SS blades and complete with induction Motor suitable for operation with 230 V single phase 50 Hz with suitable frame etc. as per IS:2312-1967 with gravity dampers for exhaust complete as per specifications and drawings.The quoted price shall consist of mounting arrangemnt for the fan. The maximum sound level of unit shall be 40dB(A) @ 3 m from source. 100 DIA

EXHAUST AIR GRILL Supplying, Installing, testing and commissioning of powder coated extruded aluminium exhaust air grille with min.60 % free area, with metallic frame work & fixing accessories, to be fixed on external wall to exhaust air from basement area to ambient , it shall be suitable for exhausting required air in CFM . Louvers need to be suitable in order avoid rain water entry in to basement @ 15 degree deflection with bird screen complete as per specification approved drawings and schedules.

FRESH AIR GRILL Supplying, installing, testing and commissioning of GI construction fresh air louvers with min. 60 % free area, bird screen and painted in baked enamel shade as per clients or architect approval with metallic frame work complete as per specification approved drawings and schedules.

FRESH/EXHAUST AIR LOUVRE Supplying, installing, testing and commissioning of GI construction fresh/exhaust air louvers with min. 60 % free area, bird screen and painted in baked enamel shade as per clients or architect approval with metallic frame work complete as per specification approved drawings and schedules.

DUCT ACOUSTIC LINING Supply ,Installation,testing and commissioning of duct acoustic lining of supply air duct and plenum with 15 mm thick Open Cell engineered Nitrile Rubber foam of density 140-180 kg/cu.m with in built Microban and tested as per ISO 354:2003 complete as required and as per specifications. 15 mm thick

DOUBLE LAYER CANVAS CONNECTION Supply,Installation,testing and commissioning of double Layer canvas connection fire retardant cloth for the end connection of AHU/CSU/AIR WASHER/SCRUBBER/TFA and Ventilation fan to reduce the vibration.It shall be fire rated for atleat 2 hrs.Refer tender specification for detail description

LAG COATIONG FOR DUCT INSULATION The duct in internal areas shall be insulated as specified and the insulated duct shall be coated by Fevicol AC Duct King Lag coating for protection against Mechanical damage, Fungal growth, Flame spread, Water Permeance. The coating shall confirm UL723 for surface burning characteristics. The coating should comply the complete specification. 19 mm on Supply/Return duct

WEATHER PROTECT COATIONG FOR DUCT INSULATION The duct in exposed area shall be insulated as specified and the insulated duct shall be coated with Fevicol Weather Protekt Coat for protection against Mechanical damage, Water Permeance Fungal growth, Flame spread, and Weathering Reistance. The product should comply complete specification. 19 mm on Supply/Return duct

MEDICAL GAS PIPELINE SYSTEM Fully Automatic Oxygen Control System :Fully Automatic Oxygen Control System ,2000 LPM as per medical device directive (93/42/EEC) from notified body with 4 digit number. As per specification.

Oxygen Manifold (2X15) : (2x15 size) Oxygen Supply System Without Cylinder. As per specification.

Emergency Oxygen Manifold (1x10): Emergency Oxygen Regulater 1x10 cylinder manifold complete with tail pipes NRV, Without Cylinder. As per specification.

Fully Automatic Oxygen Control System :Fully Automatic Nitrous Oxide Control System ,500 LPM as per medical device directive (93/42/EEC) from notified body with 4 digit number. As per specification.

Nitrous Oxide Manifold System, (2x3 size): Nitrous Oxide Manifold system without Cylinder. As per specification.

Emergency Nitrous Oxide Manifold System, (1x3): Emergency Nitrous oxide regulator 1 x 3 cylinder manifold complete with tail pipes NRV, Without Cylinder. As per specification.

Fully Automatic Oxygen Control System :Fully Automatic CO2 Control System ,500 LPM as per medical device directive (93/42/EEC) from notified body with 4 digit number. As per specification.

CO2 Manifold System, (2x3 size): CO2 Manifold system without Cylinder. As per specification.

Emergency CO2 Manifold System, (1x3): Emergency CO2 regulator 1 x 3 cylinder manifold complete with tail pipes NRV, Without Cylinder. As per specification.

Gas Outlet Points/ Terminal Units with probe as per specification Oxygen Outlet

Vacuum Outlet

CO2 Outlet

MA-4 Outlet

MA-7 Outlet

Nitrous Oxide Outlet

Medical Grade Copper Tube / Pipe : in accordance with BS EN 13348:2008 on Surface or Ceiling with hanging arrangement etc as required. 108 mm OD X 1.5mm thick

76 mm OD X 1.5mm thick

54mm OD X 1.2mm thick

42mm OD X 1.2mm thick

28mm OD X 0.9 mm thick

22mm OD X 0.9 mm thick

15mm OD X 0.9 mm thick

12mm OD X 0.9 mm thick

Ward Vaccum Unit : Ward Vacuum unit Suction trap & Replaceable Bacteria filter with 600 ML all polycarbonate jar 63mm Guage Dial )

BPC Flowmeter with humidifier bottel Safety valve ) (0-15 LPM)

High Pressure tube

Area Valve Box with Alaram complete as per technical specifications enclosed. :- 2 Gas Service

3 Gas Service

6 Gas Service

Master Alarm Panel complete as per technical specifications enclosed. :- Master Alarm Panel

ANAESTHETIC GAS SCAVENGING PLANT (AGSS)

Bed Head Panles of 1000 mm:- Provision for 2 Gas Outlet(02-1+Vac-I) with 5/15 Amp. Switch & Sockets and provision for Nurse call system. The size of the panel to be 1000 mm

Bed Head Panels of 1200 mm:- Providing wiring and piping connctions for bed head wall panels. The panel shall be fabricated out of high strengths extruded alluminium sections with inbuild single rolling and powder coated to color as per the owners choice. the panel shall have provision to accomodate: Max. 5 nos of Gas outlets, 5/15 A multi pin switched socket outlets -4 nos, 1 nos Nurse call switch panel with wired remote. 1 no. arm lamp 60W with adaptor, 1 no infusion pump rail mount pole with adapter, and holder for vacuum collection jar.

LINE ISOLATION VALVES: Line Isolation Valves as per specification 15 mm Isolation valve

22 mm Isolation valve

28 mm Isolation valve

42 mm Isolation valve

54 mm Isolation valve

76 mm Isolation valve

108 mm Isolation valve

Modular OT & Component for 8 Major OT’s & Obg. OT & Gyn. OT’s 2 nos ( Total 10 OT’s) PLENUM : As per NABH standards 1.Plenum MOC : Stainless steel 304, Thickness 1.2mm 2.Plenum Size : 8ft*8ft 3.Plenum Diffuser Grill : The high quality S.S.304 - Diffuser grill for securing unidirectional air flow according to EN ISO 14644. 4.Diffuser grill : SS 304 grill designed to deliver uniform air velocity across the entire HEPA plenum to maintain uniform air displacement on the OT table. Thickess : 1.2mm 5.Filter housing and pressure chamber : MOC stainless steel 304 matt polish, thickness 1.2 mm. 6.Filter section : - Mini-pleat (H14) grade HEPA Filters - Filters to be tested to remove partical sizing up to 0.3.micron. 7.Hepa Filter size & qty.: - Total 6-8 nos Filters - Total Filter Area : 62-64 Sq.ft. for 8*8ft - Make : AAF 8.Plenum Lights : LED light box on all 4 sides with LED tubes Box size 200mmx2000mm. LED tube light of 18watt - 8 nos. total

SURGEON'S CONTROL PANEL : Daytime Clock, Elapsed Clock, Temperature indicator, Humidity indicator, Room pressure indicator, Controle switches for Mains, AHU, OT peripheral lights.

GRILL WITH DAMPER : SS 304 Return air grills with alluminum damper to control airflow

Modular Wall SS 304 PUF panels - 50mm thick panel, One side SS 304 , thickness 0.8mm thick, Jindal Make, Mat finish with PVC laminated and other side PPGL (Pre painted gavalume) 0.5mm thick RAL 9003, Jindal Make. PUF insulation density - 40kg/Cum. All four sides of panels has alluminum extruded sections for support.

8mm thick, toughened Glass Panels Panel thickness : 50mm with toughened glass of 8mm Panel size : 8ft. x 4ft. x 2 Nos. Antibacterial qualitites of Glass - The glass panels in the OT improve the overall anti- bacterial properties of the wall panels. Better aesthetics in the OT - The glass panels shall have a impregnated Printed / Graphical image. However, the glass panel shall have no uneven / rough surfaces after the printing.

False Ceiling SS 304 PUF panels - 50mm thick panel, One side SS 304 , thickness 0.8mm thick, Jindal Make, Mat finish with PVC laminated and other side PPGL (Pre painted gavalume) 0.5mm thick RAL 9003, Jindal Make. PUF insulation density - 40kg/Cum. All four sides of panels has alluminum extruded sections for support.

Alluminum/ SS 304 Coving for floor to wall joints, wall to wall joints, ceiling to wall joints.

Hermatically sealed automatic sliding door 2000mm x 2400mm MOC : HPL CANOPY : Coated Steel Plate, Finished In RAL 9006 (Aluminum Colored Steel) With A Sloping Top. RAIL CONSTRUCTION : Aluminum Profile DOOR BLADE : 60 Mm Thick With 0.6mm HPL On Both Sides. The Above Panel Will Be Framed In Anodized Aluminum Profiles. GASKET : On All 4 Sides Of The Door Blade Is A Special Rubber Gasket. OPENER : Stainless Steel Lever Handle On Both Sides WINDOW : 300mm X 300mm DOOR FRAME : Single Aluminum Frame Profile, Fixed To Finished Wall, Not Wall Surrounded AUTOMATION : Electric, Type SDA-04, 230V SAFETY : Photocell In The Frame SWITCHES : Radar Hand Switch, Foot Switch LOCK : Manual lock MEDICAL EARTHING : Required

Hermatically sealed automatic sliding door 1200mm x 2400mm MOC : HPL CANOPY : Coated Steel Plate, Finished In RAL 9006 (Aluminum Colored Steel) With A Sloping Top. RAIL CONSTRUCTION : Aluminum Profile DOOR BLADE : 60 Mm Thick With 0.6mm HPL On Both Sides. The Above Panel Will Be Framed In Anodized Aluminum Profiles. GASKET : On All 4 Sides Of The Door Blade Is A Special Rubber Gasket. OPENER : Stainless Steel Lever Handle On Both Sides WINDOW : 300mm X 300mm DOOR FRAME : Single Aluminum Frame Profile, Fixed To Finished Wall, Not Wall Surrounded AUTOMATION : Electric, Type SDA-04, 230V SAFETY : Photocell In The Frame SWITCHES : Radar Hand Switch, Foot Switch LOCK : Manual lock MEDICAL EARTHING : Required

Vinyl flooring with self leveling Make : Tarket 2mm Flooring in operation theatre should be seamless with perfectly curved flush-coving, resistant to mechanical stress and dynamic loads and having protection characteristic (Conductive), Vinyl Specifications - Thickness @ 2mm, Washable vinyl in Sheet form. Vinyl properties - Complies to EN 433, EN 649, EN 1815, EN 1081 standards TVOC as per AgBB / DIBt Certifications, ISO 16000-6 It should have antibacterial, antifungal properties.

X-Ray View Panel Specifications - Light : LED light display - Display : 2 Film display - Dimensions - 880 x 503 x 29mm - Auto film insertion Operations : - Flicker free luminance for the film viewing purpose - Provision for brightness control - Digital Dimmer for high quality film interpretation Installation / Fitment : - flushed with theatre wall for hygienic and ease of cleaning purpose..

Pass Box : • Mechanical interlocking which is maintenance- free, fail safe and maintains cleanroom integrity by preventing both doors from being opened at the same time. • The main body of the pass box is constructed of MEDICAL - grade stainless steel ( S. S. 304 ). • The pass box base surface is constructed of stainless steel, making the work zone easy to clean. • The door of pass box is double skin with the 300*300mm glass at the centre. • Medical grade U.V. tube for sterilization of inside material. • Internal size of pass box is 450 mm W x 450 mm H x 450 mm L

Magnetic writing board with duster Colour - Pure white Size : 600mm x 800mm MOC : Magnetic laminated board bonded with 10mm high density fiber board sheet Thickness - 1.50 mm thick

Peripheral Lights / OT Luminaries: LED Type Technical specifications : 1.Recess mounted IP54 Protocol 2. Non-hygroscopic peripheral lights. 3.Size : 2ft x 2ft

Surgical Scrub :- 2 bay Scrub Designed with contoured anti splash fronts to reduce the risk of back splashing. The units also have both reduced internal and external corners for ease of cleaning, and for superior hygiene. Unit is Floor mounted with sloppy radius chamber The surgical scrub utilizes 16 gauge, type 304 as our standard , two station system with stander accessories- 2 Electric sensor operated & Foot Switch operated washing spouts, 2 manual wire rod Holders for liquid detergent container, Flashback and with nylon adjustable leveling bullets for legs Mixer arrangment for hot and cold water. (Gyser at client scope) 2 bay - 1300mm * 1000mm * 600mm

OT Light with Camera : The OT Light Should be ceiling Mounted Double Dome high performance OT Light based on LED Technology The specification includes all the mechanical and electrical components required for ceiling installation and commissioning of the light. Should be US FDA /European CE Certified, and ISO 13485 approved product. Electrical safety conforms to the standards for electrical safety IEC 60601-1 General requirements Light should consist of central Axis, Horizontal Arm, Height Adjustable spring Arm and cardanic system for the light head dome. This suspension should be drift free & Laminar flow compatible. The Dome and suspension should be sealed dust proof. All the main joints at central axis should have unlimited 360 degree mobility. There should be central, steriliseable, exchangeable handle for sterile positioning of the light. Head/Dome size 700mm approx. Light Source high power life LED: 50,000hrs or more. This should be substantiated by a digital hour counter on the control panel.

The light should have multi colour LEDs for excellent tissue differentiation during surgery, thereby reducing strain and fatigue on the surgeon's eyes, when operating for long hours. Light Field should be adjustable from 15cm to 30cm, digitally adjustable from the control panel on the light dome and by wireless remote control. Illumination by each dome; 160000 lux at 1 mtr. With intensity controller 4/5 multiple step level of discrete position. Colour Temperature adjustable in 4 steps from 3500-4000-4500-5000K . Number of LED's in each dome: More than 50nos Colour Rendering Index: 95 or more. Heat to Light Ratio: 3.40 m W/Lux- Sq meter or lower. Light must include Full HD camera (detachable) with auto focus, mounted at the centre or one of the light head, with camera resolution 1920X 1080 (10 X optical & 12X digital zoom) Both camera and light controls should be available on the control panel, and also on the wireless remote control for ease of use. Must include at least 21" Full HD color display to be mounted on third arm and necessary cabling. A HD Recorder should be provided to facilitate recording of images transmitted from the camera. Switching the Light Head on/off, changing of intensity, light field diameter change, and endo function & full Camera controls, should be possible from control panel fixed on light dome handle, and also by outside sterile zone of light through cordless remote control.

Pendants - 2nos. for each OT ( 1 surgical and 1 Endoscopy) : The Ceiling Pendant should be designed to provide convenient positioning of medical equipment, medical gas terminal units & electrical points. It should be European CE notified body/US FDA Certified. The aluminum-extruded profile should very sturdy. Facilities for medical gases & electrical points are ready for connection at central incoming point on the vertical ceiling point. Connection of medical gases and electrical components to the hospital system is provided through the vertical aluminium suspension profile. It should have the following :- 1 vertical suspensions inclusive heavy ceiling flanges and false ceiling covers, 320° revolving., Each Pendant should have 5 Gas Outlets : Oxygen 2 nos, Air 1 no, Vaccuum 1 no, CO2 / N2O -1no. 8nos. Electrical multipin switch + socket of Indian Origin 6/16amp with plate. , 2nos. Data socket RJ45 cat 6, wiring to be executed at site., 2 Potential Earthing Equalization sockets with inside wiring. Surgical Pendant should be supplied with one vertical column with 2 shelves & 1 drawer for various medical devices having a load bearing capacity of minimum 80 Kg.

Endoscopy Pendant should be supplied with one vertical column with both side supports, with 4 shelves & 1 drawer for various medical devices having a load bearing capacity of minimum 100 Kg. The lids should be removable to allow access to the aluminum sections. Segregation shall be provided within the side sections to ensure that services are not accessible when removing the lid. Should have either friction brake or pneumatic braking for firm positioning.

Minor / Emergency OT’s 2 Nos. Modular Wall PPGI PUF panels - 50mm thick panel, Both side PPGL (Pre painted gavalume) 0.5mm thick RAL 9003, Jindal Make. PUF insulation density - 40kg/Cum. All four sides of panels has alluminum extruded sections for support.

8mm thick, toughened Glass Panels Panel thickness : 50mm with toughened glass of 8mm Panel size : 8ft. x 4ft. x 2 Nos. Antibacterial qualitites of Glass - The glass panels in the OT improve the overall anti- bacterial properties of the wall panels. Better aesthetics in the OT - The glass panels shall have a impregnated Printed / Graphical image. However, the glass panel shall have no uneven / rough surfaces after the printing.

False Ceiling PPGI PUF panels - 50mm thick panel, Both side PPGL (Pre painted gavalume) 0.5mm thick RAL 9003, Jindal Make. PUF insulation density - 40kg/Cum. All four sides of panels has alluminum extruded sections for support.

Alluminum/ SS 304 Coving for floor to wall joints, wall to wall joints, ceiling to wall joints.

Hermatically sealed automatic sliding door 1200mm x 2400mm MOC : HPL CANOPY : Coated Steel Plate, Finished In RAL 9006 (Aluminum Colored Steel) With A Sloping Top. RAIL CONSTRUCTION : Aluminum Profile DOOR BLADE : 60 Mm Thick With 0.6mm HPL On Both Sides. The Above Panel Will Be Framed In Anodized Aluminum Profiles. GASKET : On All 4 Sides Of The Door Blade Is A Special Rubber Gasket. OPENER : Stainless Steel Lever Handle On Both Sides WINDOW : 300mm X 300mm DOOR FRAME : Single Aluminum Frame Profile, Fixed To Finished Wall, Not Wall Surrounded AUTOMATION : Electric, Type SDA-04, 230V SAFETY : Photocell In The Frame SWITCHES : Radar Hand Switch, Foot Switch LOCK : Manual lock MEDICAL EARTHING : Required

Vinyl flooring with self leveling Make : Tarket 2mm Flooring in operation theatre should be seamless with perfectly curved flush-coving, resistant to mechanical stress and dynamic loads and having protection characteristic (Conductive), Vinyl Specifications - Thickness @ 2mm, Washable vinyl in Sheet form. Vinyl properties - Complies to EN 433, EN 649, EN 1815, EN 1081 standards TVOC as per AgBB / DIBt Certifications, ISO 16000-6 It should have antibacterial, antifungal properties.

X-Ray View Panel Specifications - Light : LED light display - Display : 2 Film display - Dimensions - 880 x 503 x 29mm - Auto film insertion Operations : - Flicker free luminance for the film viewing purpose - Provision for brightness control - Digital Dimmer for high quality film interpretation Installation / Fitment : - flushed with theatre wall for hygienic and ease of cleaning purpose..

Magnetic writing board with duster Colour - Pure white Size : 600mm x 800mm MOC : Magnetic laminated board bonded with 10mm high density fiber board sheet Thickness - 1.50 mm thick

Peripheral Lights / OT Luminaries: LED Type Technical specifications : 1.Recess mounted IP54 Protocol 2. Non-hygroscopic peripheral lights. 3.Size : 2ft x 2ft

Surgical Scrub :- 2 bay Scrub Designed with contoured anti splash fronts to reduce the risk of back splashing. The units also have both reduced internal and external corners for ease of cleaning, and for superior hygiene. Unit is Floor mounted with sloppy radius chamber The surgical scrub utilizes 16 gauge, type 304 as our standard , two station system with stander accessories- 2 Electric sensor operated & Foot Switch operated washing spouts, 2 manual wire rod Holders for liquid detergent container, Flashback and with nylon adjustable leveling bullets for legs Mixer arrangment for hot and cold water. (Gyser at client scope) 2 bay - 1300mm * 1000mm * 600mm

OT Light Double Dome : The OT Light Should be ceiling Mounted Double Dome high performance OT Light based on LED Technology The specification includes all the mechanical and electrical components required for ceiling installation and commissioning of the light. Should be US FDA /European CE Certified, and ISO 13485 approved product. Electrical safety conforms to the standards for electrical safety IEC 60601-1 General requirements Light should consist of central Axis, Horizontal Arm, Height Adjustable spring Arm and cardanic system for the light head dome. This suspension should be drift free & Laminar flow compatible. The Dome and suspension should be sealed & dust proof. All the main joints at central axis should have unlimited 360 degree mobility. There should be central, steriliseable, exchangeable handle for sterile positioning of the light. Head/Dome size 700mm approx. Light Source high power life LED: 50,000hrs or more. This should be substantiated by a digital hour counter on the control panel.

The light should have multi colour LEDs for excellent tissue differentiation during surgery, thereby reducing strain and fatigue on the surgeon's eyes, when operating for long hours. Light Field should be adjustable from 15cm to 30cm, digitally adjustable from the control panel on the light dome and with a cordless remote control. Illumination by each dome; 160000 lux at 1 mtr. With intensity controller 4/5 multiple step level of discrete position. Colour Temperature adjustable in 4 steps from 3500-4000-4500-5000K . Number of LED's in each dome: More than 50nos Colour Rendering Index: 95 or more. Heat to Light Ratio: 3.40 m W/Lux- Sq meter or lower. Switching the Light Head on/off, changing of intensity, light field diameter change, and endo function, should be possible from control panel fixed on light dome handle, and also by outside sterile zone of light through cordless remote control.

Pendants - 1no. for each OT ( surgical ) : The Ceiling Pendant should be designed to provide convenient positioning of medical equipment, medical gas terminal units & electrical points. It should be European CE notified body/US FDA Certified. The aluminum-extruded profile should very sturdy. Facilities for medical gases & electrical points are ready for connection at central incoming point on the vertical ceiling point. Connection of medical gases and electrical components to the hospital system is provided through the vertical aluminium suspension profile. It should have the following :- 1 vertical suspensions inclusive heavy ceiling flanges and false ceiling covers, 320° revolving., 5 nos. Gas Outlets : 2 nos Oxygen, 1 Air, 1 Vaccuum, 1 N2O or CO2, 8nos. Electrical multipin switch + socket Indian type 6/16amp with plate. , 2nos. Data socket RJ45 cat 6, wiring to be executed at site., 2 Potential Earthing Equalization sockets with inside wiring. Surgical Pendant should be supplied with one vertical column with 2 shelves & 1 drawer for various medical devices having a load bearing capacity of minimum 80 Kg. The lids should be removable to allow access to the aluminum sections. Segregation shall be provided within the side sections to ensure that services are not accessible when removing the lid. Should have either friction brake or pneumatic braking for firm positioning.

CSSD (Central Sterile Supply Department) Ultrasonic cleaner bench top of capacity 45 Liters suitable for operation on 230V, 50 Hz AC Supply. The units should be a compact bench top model, with a built-in tank, manufactured from high-quality SS 304/316 stainless steel and a solid-state generator that sends ultrasonic (approx. 40 KHz) impulses through wash water containing detergent and electrical heating;

SS Working table of minimum Size (LxWxH) :1800x650x900 mm complete as per technical specifications attached.(For Dirty & Clean Zone)

SS Washing Table with two sink complete of Minimum Size (LxWxH) : 2000x750x850 mm

SS Transport Trolley 4 swivel wheels, mounted in ball bearings, for easy handling made of all-welded medical grade SS tubing with handlebars & minimum size: 1080 x 550 x 800 mm. (For Dirty ,Clean & Sterilization Zone)

Design & Supply of SS Storage Shelf 5 shelves based on single free-standing shelf modules for storage of clean linen, instruments, and packing material or sterilized goods, including disposables & Minimum Size (LxWxH) :1500x450x1900 mm (For Dirty ,Clean & Sterilization Zone)

Double Door Washer/Disinfector with minimum 12 DIN capacity including Surgical Instrument Trolley-1Nos, External Trolley -2 Nos. & 12 Nos. 1 DIN Trays

SS Pass Box made up of SS 304 sheets with double wall construction & minimum Size:600x600x600mm (internal).(For Dirty ,Clean & Sterilization Zone)

Air & Water Gun rinse unit designed for connection to water or compressed air, to use for assisted cleaning of pipettes, catheters, cannulas, syringes etc. The spray-gun should include tubing and different tips and nozzles for the various cleaning purposes, like syringes and cannulas with Record cone, Measuring and blood pipettes, Catheters and small pipes, Drainage tubing, Syringes and cannulas with Lure cone, Spray jet for rapid instrument cleaning, Bottles and Erlenmeyer flasks, Water jet pumps for suction cleaning, complete as per technical specifications attached.

SS Closed Transport Trolley For Dirty Material Transport SIZE: 1400x750x1260 mm (LxWxH) (External) approximately for sterile goods handling, for which higher protection than normal dust protection is required. It should be suitable for handling baskets or containers with a total capacity of 9 STU (1 STU = 600 x 300 x 300 mm) on three solid, removable shelves (3 x 3) STU

SS Stool For operators Steel top and adjustable height from 450mm to680 mm, through mild steel threaded screws. It should have four legged base made of 25mm steel tube mounted on rubber shoes with SS ring for footrest & pre-treated Epoxy powder coated frame work for operators complete as per technical specifications attached.(For Dirty ,Clean Zone)

SS Control and Packing table of minimum size (LxWxH): 2000x1500x900 mm (±10%) specially designed for sorting, inspection, functional control and packing of various sets for wards, clinics etc. and for surgical instrument sets in trays. The worktop should be made of SS (304) All edges should be smooth complete as per technical specifications attached.

Inspection lamp with magnifier

Heat Sealing machine Rotary heat sealers should provide validated sealing of sterilization bags and clear‐view pouches (paper/plastic laminate).It should be microprocessor‐controlled.The warm‐up time should not exceed 30 seconds.The temperature should be adjustable from 50‐200°C with a tolerance of 1% of the set value complete as per technical specifications attached.

SS Roll holder with cutting knife: Approx Size (LxWxH) 260x60x120mm.This dispenser for sterilizer tape should hold two reels of tape.The heavy-duty bottom plate should be fitted with anti-slip rubber to prevent the dispenser fro slipping when tape is torn off.

Paper dispensing trolley- It Should be movable trolley for storing four different sizes of sterilizing wrapping paper sheets should be made of stainless steel tube. It Should have four ball bearing rubber wheels, of which two wheels should be equipped with brakes.

Double door Drying Cabinet of capacity 280 Litres It Should be automatic in operation and Inner chamber should be made up of stainless steel and outer chamber should be of epoxy painted CRCA sheets.It Should have heaters of minimum 2 KW.

SS Linen Fold table with Size 2000x1400x900mm The table should be specially designed for sorting, inspection (each piece of linen can be moved over an illuminated inspection panel) and folding of surgical dressing sets and individually packaged towels/gowns. The extended width also facilitates work with large dressing sheets. Work can be carried out comfortably, either sitting or standing complete as per technical specifications attached.

Gauze cutting machine .ItShould be useful in cutting thickest of cotton gauze material.It Should consist of a cutting unit and a knife sharpening unit.The Blade size should be approx. 200 mm and Cutting Capacity should be 165 mm.

Documentation Labeller-The labeller should be 3 line for printing the following information- person resposnsibile for sterilization, producation and expiry date

Steam Sterilizer with pass through double door (850-900 liters) with minimum 12 STU capacity with Internal Trolley - 1 Nos, External Trolleys - 2 Nos & Stainless Steel Baskets - 18 Nos. complete as per technical specifications attached.

Low Temperature Steam Formaldehyde (LTSF) with pass through double door (550-600 liters) with 08 STU capacity with 1 No. Internal & 2 Nos. External Trolleys & 08 Nos. Stainless Steel Baskets of 1 STU

Single Door With WashingFunction Prismatic Autoclave Sterilizer 250 Ltr

SS Closed Transport Trolley for Sterile Material Transport SIZE: 1400x750x1260 mm (LxWxH) (External) approximately for sterile goods handling, for which higher protection than normal dust protection is required. It should be suitable for handling baskets or containers with a total capacity of 9 STU (1 STU = 600 x 300 x 300 mm) on three solid, removable shelves (3 x 3) STU

Audio Video System for Lecture theaters Supply, Installation, Testing and Commissioning of Digital Wireless Handheld Microphone with cardioid pick up pattern, operating on 1.9 GHz bandwidth, 256 bit AEC Encryption, AF Frequency response: 20 Hz-20 kHz, Dynamic range: > 120 dB, Audio Sampling: 24 bit/48 kHz, RF Power: adaptive 200 mW , Receiver with front panel LCD/LED Display, 7-band Graphic equalizer, LAN port for control and Monitoring, complete as required.

Supply, Installation, Testing and Commissioning of Digital Wireless Lapel Microphone with omni directional pick up Pattern, operating on 1.9 GHz bandwidth, 256 bit AEC Encryption, AF Frequency response: 20 Hz-20 kHz, Dynamic range: > 120 dB, Audio Sampling: 24 bit/48 kHz, RF Power: adaptive 200 mW, Receiver with front panel LCD/LED Display, 7-band Graphic equalizer, LAN port for control and Monitoring, complete as required.

Supply, Installation, testing and commissioning of Goosneck Microphone of 12" to 16" with Polar Pattern : Cardioi, Element : Dual Condenser (back-electret) , Frequency Response : 100 - 20,000 Hz complete with base Stand of same make with on/off button, LED Indication for Mic Status, RFI/ GSM Shielding along with shock mount complete as required.

Supply, Installation, testing and commissioning of Full range loudspeaker with Frequency Range: 73 Hz - 15 kHz, Nominal Coverage Pattern: 120° H x 60° V, Power Handling, long-term continuous: 120 W (480 Watt Peak), Sensitivity: 91 dB, Maximum SPL: 112 dB (118 dB Peak), Full range driver: 4 x 4.5" drivers, Nominal Impedance: 8 ohms, Enclosure Material: Mineral-reinforced HDPE Grille, Powder- coated steel grille along with IEC 529 IP55 environmental protection.

Supply, Installation, testing and commissioning of Dual Channel amplifier with Power Output: 2 x 300 Watt @ 4 ohm, 8 ohm, 70/100V, Gain: 50 dB, Channel Separation (Crosstalk) > 85 dB, Signal to Noise Ratio: 100 dB, Audio Inputs: 2 unbalanced, 2 balanced, Input Impedance: 10 kΩ (RCA), 20 kΩ (Euroblock) Maximum Input Level 20 dBu, Audio Outputs: 2, Built-in DSP: 24-bit / 48 kHz A/D and D/A converter, Processing functions: Standard mixer, loudspeaker EQ, 9-band PEQ, Vpeak/Vrms limiters, delay, band pass, mute/output polarity inversion, Protection: High temperature, output short, extra high frequency (EHF), excessively low or high AC line voltage.

Supply, installation, testing & comissioning of Modular Digital Signal Processor with current configuration of minimum 6mic/line inputs and 2line outputs, 2 x 2 USB in/out for PC audio, Dante connectivity and future expansion for AEC, Processor: 40 bit floating point, Sampling rate: 48kHz, standard Dante digital audio networking.

Supply, installation, testing & comissioning of 2 core 1.5 sqmm PVC insulated CU conduction loudspeaker cable.

Supply, installation, testing & comissioning of 2 core shielded microphone cable.

Supply, Installation, Testing and Commissioning of minimum 6750 Lumens, WUXGA, Single Chip Laser DLP Projector, Native 16:10, Display: 1 x 0.67” DMD, Contrast ratio: 4,000,000:1, Resolution :Up to 1,920 x 1,200, inputs: 2 x HDMI, 1x DVI-D, 1 x HDBaseT, 1 x VGA, Signal outputs: 1 x HDMI, Pixel clock: 162MHz, Control port: RS232, HDBaseT, Ethernet, IR, 20,000 hours life along with 24 /7 operation, complete as required.

Supply, installation, testing & comissioning of 150" diagonal motorized projection Screen.

Supply, Installation, Testing and Commissioning of Mettalic Podium with Interactive 21" or higher Tablet Monitor, Presentation Plate, desktop PC with provision to place document camera, Switcher, Amplifier, PC, etc complete with standard accessories, complete as required.

Supply, Installation, Testing and Commissioning of Full HD PTZ Camera for capturing the Presenter, minimum 20X Optical Zoom, min 100 Presets, 60 Frames per Second, Ethernet Out, HDMI Out, 3G-SDI Out, Audio In, RS232/422/Ethernet Controls, -170° ~ +170° Panning angle, -30° ~ +90° Tilting angle , Should support PoE+.

Supplying, installation, testing and commissioning of switcher with inbuilt capacity of recording and streaming with 4 HDMI Inputs and IP video sources, 3 x H.264/AVC digital video over Ethernet 2 x HDMI output, scaling and window processing, supports PIP, PBP and up to 4 windows layout and mixing, 1TB HDD internal storage, Audio Input: 4 Line In/MIC In, Audio Output: 3 x Stero, 2 x USB, 1 x RS-232 /RS-485 port along with 1 x RJ-45 ethernet port.

Supply, installation, testing and commissioning of 4K60 HDMI Transmitter with 3 x HDMI input, 1 x VGA, 1 x HDBaseT input port, 1 x HDBaset and 1 x HDMI output port, HDCP 2.2 compliant, Supports deep color, x.v.Color, lip sync, HDMI uncompressed audio channels, Dolby TrueHD, DTS–HD, 2K, 4K, and 3D and Up to 32 channels of digital stereo uncompressed signals.

Supply, installation, testing and commissioning of 4K60 HDMI Receiver with 1 x HDBaseT input port, 1 x HDMI output port, Control Port: 1 x IR, 1 x RS-232, HDCP 2.2 compliant, Supports deep color, x.v.Color, lip sync, HDMI uncompressed audio channels, Dolby TrueHD, DTS–HD, 2K, 4K, and 3D and Up to 32 channels of digital stereo uncompressed signals.

Supply, installation, testing and commissioning of Wireless Presentation System with 4K resolution, enables iOS, Android, Chromebook, PC, and Mac device users to instantly connect to a main display without a dongle, 2.4GHz/5GHz Wi–Fi and MIMO antennas, Two participants can simultaneously present content on main display along with in-built processor of Intel, Main Memory: 4GB, Storage: 32 GB, Networking: 802.11 ac/b/g/n dual band Wireless LAN and Bluetooth 4.1, Operating System: Linux. .

Supply, installation, testing & comissioning of 9.7" wireless I-Pad.

Supply, installation, testing & comissioning of 8 Port Network Switch.

Supply, installation, testing & comissioning of wi-fi Router.

Supply, installation, testing and commissioning of 2 mtr. HDMI- HDMI Patch Cords.

Supply, installation, testing and commissioning of 4 core shielded twisted pair cat5/Cat6 cable.

Supply, Installation, Testing and Commissioning of Digital Wireless Lapel Microphone with omni directional pick up Pattern, operating on 1.9 GHz bandwidth, 256 bit AEC Encryption, AF Frequency response: 20 Hz-20 kHz, Dynamic range: > 120 dB, Audio Sampling: 24 bit/48 kHz, RF Power: adaptive 200 mW, Receiver with front panel LCD/LED Display, 7-band Graphic equalizer, LAN port for control and Monitoring, complete as required.

Supply, Installation, Testing and Commissioning of Digital Wireless Handheld Microphone with cardioid pick up pattern, operating on 1.9 GHz bandwidth, 256 bit AEC Encryption, AF Frequency response: 20 Hz-20 kHz, Dynamic range: > 120 dB, Audio Sampling: 24 bit/48 kHz, RF Power: adaptive 200 mW , Receiver with front panel LCD/LED Display, 7-band Graphic equalizer, LAN port for control and Monitoring, complete as required.

Supply, Installation, Testing and Commissioning of 16 Watt Ceiling Speaker with Frequency Response: 95 Hz - 17 kHz, Frequency Range: 80 Hz - 19 kHz, Nominal Dispersion: 140° conical, Long-Term Power Handling: 16 W (64 W peak), Sensitivity: 84 dB SPL, Maximum SPL: 96 dB SPL (102 dB SPL peak, Nominal Impedance: 8 Ω, Transformer Taps @ 100 V: 2 W, 4 W, 8 W, 16 W, Driver Compliment: 2.25" full- range driver, Enclosure: PC/ABS Grille, Powder-coated steel grille.

Supply, Installation, Testing and Commissioning of Dual Channel Class D amplifier with amplifier power: 2 x 50 Watt @ 4 ohm, 2 x 25 Watt @ 8 ohm, Frequency response: 20 Hz to 20KHz, THD+N: 0.3%, Channel seperation (Crosstalk): 60dBv, Dynamic range: 88 dB, 1 x unbalanced line input, 2 x outputs..

Supply, installation, testing & comissioning of Modular Digital Signal Processor with current configuration of minimum 6mic/line inputs and 2line outputs, 2 x 2 USB in/out for PC audio, Dante connectivity and future expansion for AEC, Processor: 40 bit floating point, Sampling rate: 48kHz, standard Dante digital audio networking.

Supply, installation, testing & comissioning of 2 core 1.5 sqmm PVC insulated CU conduction loudspeaker cable.

Supply, installation, testing & comissioning of 4K60 HDMI & VGA Wall–Plate Auto Switcher/Transmitter with Built–in intelligent Room Automation, Up to 100m (330ft) standard HDBaseT Extension, Input Ports: 1 x HDMI, 1 x VGA, Output: 1 x HDBaseT, 1 x Unbalanced Stereo Audio, Control Ports: 2 x RS-232, 1 x 100BaseT Ethernet, 4 Contact-Closure Switches, HDMI Support: Deep color, x.v.Color™, lip sync, HDMI uncompressed audio channels, Dolby TrueHD, DTS HD, 2K, 4K, and 3D as specified in HDMI 2.0, Max. Level: 3.1 Vpp ,THD: 0.013% , SNR: –70dB

Supply, installation, testing & comissioning of 4K60 4:4:4 Receiver with scaler, Input Ports: 1 x HDBaseT input and Output Port: 1 x HDMI, 1 x audio out, Control Port: 1 x RS-232, 1 x IR, 1 x USB, Max. cable distance Range 100m (328ft) at 4K, 48kHz for analog audio output sampling rate,

Supply, Installation, Testing and Commissioning of 4K 75" display with Brightness- 500 nits, Native Contrast Ratio- 4000:1, Haze- 25%, Operating Hour- 24/7, Input- DVI-D, Display Port 1.2 (1), HDMI 2.0 (2), USB 2.0 x 2,Processor-Coretex A72 1.7GHz Quad-Core CPU,Storage (FDM)- 8GB (3.88GB Occupied by O/S, 4.12GB Available), Certification- BIS,EMC Class A, Safety 60950-1 complete as required.

Supply, installation, testing and commissioning of 2 mtr. VGA-VGA Patch Cords.

Supply, Installation, Testing and Commissioning of Digital Wireless Lapel Microphone with omni directional pick up Pattern, operating on 1.9 GHz bandwidth, 256 bit AEC Encryption, AF Frequency response: 20 Hz-20 kHz, Dynamic range: > 120 dB, Audio Sampling: 24 bit/48 kHz, RF Power: adaptive 200 mW, Receiver with front panel LCD/LED Display, 7-band Graphic equalizer, LAN port for control and Monitoring, complete as required.

Supply, Installation, Testing and Commissioning of Digital Wireless Handheld Microphone with cardioid pick up pattern, operating on 1.9 GHz bandwidth, 256 bit AEC Encryption, AF Frequency response: 20 Hz-20 kHz, Dynamic range: > 120 dB, Audio Sampling: 24 bit/48 kHz, RF Power: adaptive 200 mW , Receiver with front panel LCD/LED Display, 7-band Graphic equalizer, LAN port for control and Monitoring, complete as required.

Supply, installation, testing & comissioning of Modular Digital Signal Processor with current configuration of minimum 6mic/line inputs with AEC and 2line outputs, 2 x 2 USB in/out for PC audio, Dante connectivity, Processor: 40-bit floating point, Sampling rate: 48kHz, standard Dante digital audio networking.

Supply, Installation, testing and commissioning of Full range loudspeaker with Frequency Range: 73 Hz - 15 kHz, Nominal Coverage Pattern: 120° H x 60° V, Power Handling, long-term continuous: 120 W (480 Watt Peak), Sensitivity: 91 dB, Maximum SPL: 112 dB (118 dB Peak), Full range driver: 4 x 4.5" drivers, Nominal Impedance: 8 ohms, Enclosure Material: Mineral-reinforced HDPE Grille, Powder- coated steel grille along with IEC 529 IP55 environmental protection.

Supply, Installation, Testing and Commissioning of 16 Watt Ceiling Speaker with Frequency Response: 95 Hz - 17 kHz, Frequency Range: 80 Hz - 19 kHz, Nominal Dispersion: 140° conical, Long-Term Power Handling: 16 W (64 W peak), Sensitivity: 84 dB SPL, Maximum SPL: 96 dB SPL (102 dB SPL peak, Nominal Impedance: 8 Ω, Transformer Taps @ 100 V: 2 W, 4 W, 8 W, 16 W, Driver Compliment: 2.25" full- range driver, Enclosure: PC/ABS Grille, Powder-coated steel grille.

Supply, Installation, Testing and Commissioning of Four Channel Class D Power Amplifier with Amplifier Power : 4 x 150 W @ 4-8 Ω, 70/100V, THD+N: < 0.04%, Maximum power per channel: 600 W @ 4-8 Ω, 70/100V, Frequency Response: 20 Hz – 20 kHz, Channel Separation (Crosstalk): > 85 dB @ 1 kHz, Signal to Noise Ratio: 100 dB, Audio inputs: 4 x balanced, Input Impedance: 20 kΩ, Maximum Input Level: 20 dBu, Audio outputs: 4, Built-in DSP: 24-bit / 48 kHz A/D and D/A converter, Processing functions: Matrix mixer, loudspeaker EQ, real-time 9-band PEQ, Vpeak/Vrms limiters, delay, band pass, mute/output polarity inversion along with High temperature, output short, extra high frequency (EHF), excessively low or high AC line voltage protection.

Supply, Installation, Testing and Commissioning of Digital Controller and Power Supply Unit for control and management of conference system, System control for up to 80 Discussion Devices, Operating modes - Open / Override /Voice activated/Push to talk (PTT) mode, Built-in feedback suppressor or external feedback suppressor, Built-in digital recorder or an external recording via USB/SD Card, Port for Automatic HD camera control, Ethernet port for communication, Supply voltage : 100 to 240 VAC ± 10 %, Sample Frequency : 44.1 kHz, Frequency response : 30 Hz to 20 kHz, THD at nominal level < 0.5 %, S/N Raio > 94 dBA.

Supply, Installation, Testing and Commissioning of Digital Chairman unit with Microphone length of 450 - 500 mm, LED indication for Microphone On/Request to Speak, Built-in stereo headphone socket with Volume control, Immunity to mobile phone interference, slide switch at bottom for configuration as a Chairperson, Plug‑and‑play functionality, Frequency response : 200 Hz to 12.5 kHz, Loudspeaker nominal output : 72 dB SPL.

Supply, Installation, Testing and Commissioning of Digital Delegate unit with Microphone length of 450 - 500 mm, Felxible Stem, LED indication for Microphone On/Request to Speak, Built-in stereo headphone socket with Volume control, Immunity to mobile phone interference, lide switch at bottom for configuration as a participant, Plug‑and‑play functionality, Frequency response : 200 Hz to 12.5 kHz, Loudspeaker nominal output : 72 dB SPL.

Supply, Installation, Testing and Commissioning of 2m Conference Multicore Cable for loop in loop out.

Supply, Installation, Testing and Commissioning of 20m Conference Multicore Cable for loop in loop out.

Supply, installation, testing & comissioning of Cable Cubby with pass through plates of HDMI, VGA, audio along with 1 x universal Power socket.

Supply, Installation, Testing and Commissioning of minimum 6750 Lumens, WUXGA, Single Chip Laser DLP Projector, Native 16:10, Display: 1 x 0.67” DMD, Contrast ratio: 4,000,000:1, Resolution :Up to 1,920 x 1,200, inputs: 2 x HDMI, 1x DVI-D, 1 x HDBaseT, 1 x VGA, Signal outputs: 1 x HDMI, Pixel clock: 162MHz, Control port: RS232, HDBaseT, Ethernet, IR, 20,000 hours life along with 24 /7 operation, complete as required.

Supply, installation, testing & comissioning of 150" diagonal motorized projection Screen.

Supplying, installation, testing and commissioning of Chassis or Fixed Matrix Switcher having 8 x HDMI input and 8 x HDMI output, 1 USB, 1 RS–232, 1 Ethernet, 1 USB for powering an external device, Front panel buttons, 7–segment display, AFV and breakaway buttons, Independent Audio Matrix, Deep Color, 3D, ARC, up to 7.1 uncompressed audio channels, Advanced EDID Management per Input along with 16 presets for quick access to common configurations.

Supply, installation, testing and commissioning of Multiformat Box Transmitter having 1 x HDMI, 1 x VGA with audio, 1 x HDBaseT output, 2 x RS-232, 1 x ethernet port, 4 Contact-Closure Switches, Supports Deep color, x.v.Color, lip sync, HDMI uncompressed audio channels, Dolby TrueHD, DTS HD, 2K, 4K, and 3D, Built–in intelligent Room Automation

Supply, installation, testing and commissioning of 4K60 HDMI Transmitter with 3 x HDMI input, 1 x VGA, 1 x HDBaseT input port, 1 x HDBaset and 1 x HDMI output port, HDCP 2.2 compliant, Supports deep color, x.v.Color, lip sync, HDMI uncompressed audio channels, Dolby TrueHD, DTS–HD, 2K, 4K, and 3D and Up to 32 channels of digital stereo uncompressed signals.

Supply, installation, testing and commissioning of 4K60 HDMI Receiver with 1 x HDBaseT input port, 1 x HDMI output port, Control Port: 1 x IR, 1 x RS-232, HDCP 2.2 compliant, Supports deep color, x.v.Color, lip sync, HDMI uncompressed audio channels, Dolby TrueHD, DTS–HD, 2K, 4K, and 3D and Up to 32 channels of digital stereo uncompressed signals.

Supply Installation Testing & Commissioning of Control Processor , Should have minimum of 512MB RAM Built in, Should have minimum of 4GB Flash Built In, It should have Industry-standard Ethernet communications, It should have built in Web server, It should have minimum One RS-232/422/485 COM port, It should have minimum Two RS-232 COM ports, It should have minimum 4 IR/serial, It should have minimum 8 Low Voltage relay ports, It should have minimum 4 Versiport I/O ports.

Supply Installation Testing & Commissioning of 7” Wired Touch Panel with 1280x800 RGB pixels, 16:10 aspect ratio, ±85° horizontal/vertical viewing angles, 400cd/m2 brightness, 800:1 contrast ratio, 10 points, 2–finger gesture multi touch along with Front, 2M pixels, HD 720p camera.

Supply, installation, testing and commissioning of Wireless Presentation System with 4K resolution, enables iOS, Android, Chromebook, PC, and Mac device users to instantly connect to a main display without a dongle, 2.4GHz/5GHz Wi–Fi and MIMO antennas, Two participants can simultaneously present content on main display along with in-built processor of Intel, Main Memory: 4GB, Storage: 32 GB, Networking: 802.11 ac/b/g/n dual band Wireless LAN and Bluetooth 4.1, Operating System: Linux.

Supply, installation, testing and commissioning of 8 Port network Switch.

Supply, installation, testing and commissioning of Wi-fi Router.

Supply, installation, testing and commissioning of Equipment Rack - 36U.

Supply, Installation, Testing & Commissioing of 75" interactive flat panel, IR touch technology, IPS Panel UHD Native Resolution ( 3,840 x 2,160), Brightness 330 Nits; Contrast ratio 1100:1, response time :8ms, CONNECTIVITY (Input) Video / Audio HDMI (3), RGB / Audio In(Input) External Control RS232C In, RJ45 (Input) USB USB 2.0 (3, Front : 2ea, Bottom side: 1ea Only for software update), USB 3.0 (3), Touch Out(USB2.0,B Type) (2)(Output) Video / Audio HDMI (1), Optical Output / Audio Out with OPS i5 system

Supply, Installation, Testing & Commissioing of Online recording software

Supply of recording camcorder with XAVC, 4K 9QFHD) with carl Zeiss Vario Sonnar T*lens. recording format (Video):XAVC QFHD: MPEG-4 AVC/H.264 4:2:0 Long profile XAVC HD : MPEG-4 AVC/H.264 4:2:2 Long profile XAVC Proxy: MPEG-4 AVC/H.264 4:2:0 Long profile AVCHD : MPEG-4 AVC/H.264 AVCHD 2.0 format compatible DV Recording Fomat ( Audio): XAVC QFHD : Linear PCM 2ch, 24bit, 48kHz XAVC HD : Linear PCM 2ch, 24-bit, 48 kHz XAVC Proxy : AAC-LC 2ch, 16bit,48kHz AVCHD : Linear PCM 2ch, 16-bit, 48 kHz / Dolby Digital 2ch, 16-bit, 48 kHz DV : Linear PCM 2ch, 16-bit, 48 kHz

Assembeld PC with Intel Core i7-8700 8th Generation CPU -16GB RAM (DDR4- 1600, 8GB x 2) 2TB HDD With SSD 256 GB windo10 Professional license, TFT 22", wireless keyboard Mouse

Capture Card, 4k Intensity Pro

Heavy Duty Tripod Camera

Supply of Audio Microphone Caller Mic

Supply of 1500 VA UPS for Back up

Supply of Lightnings, cables, connectors

Tubewell- 2 nos & Rain Water Harvesting Pit (10 Nos) Construction of modular type rain water harvesting pit 32 cum. (For Recharge purpose) including following items. Drilling of bore well: (90 metre) Injection well insertion Upvc pipe 6'' diameter having a load capacity of 6kg/sqm Injection well insertion slotted pipes for clog resistent of rain water and reducing possibility of carrying soild. Solvent & screws for joing pipes with each other also for joinig end caps and bell plugs for bore. Clamps for keeping the pipe safe and holding the pipe while to ground level. Bell plug - supplying and fixing of bell plug with each bore well. End caps - supplying and fixing of end caps at the top of each bore well. Supply of bentonite fore bore wells drilling in order to give support and prevent from collapsing. Gravel filling for packing of empty space in the bore and to provide stability to the inserted pipes. Compressor/Boki cleaning- Earth work excavation with JCB/excavators in all types of soil/Ordinary rock/Hard rock and with a lift up to 5 meter. Material for base work (gravel/ston chips and double washed river sand) Dressing Compaction - of base soil Soil disposal - disposal of extracted soil from the site to inside the boundary walls of the building up to a maximumdistance of 0.5km Geo textile - to avoid invasion of soil provide stability to the tank and improve quality of water within the tank with tensile strength. Modular RWH modules material (685x410x408 mm) Backfilling of the area constructed in and around after compacting them properly. FRP Micro filter capable of removing soilds. Riser for filter extension.

Construction of brick masonry Desilting chamber of size 200x150x20cm Effective depth before rainy well with precast concrete block in cement mortar 1:4 (1 cement : 4 coarse sand) , foundation concrete 1:4:8 mix (1 cement : 4 coarse sand; 8 graded stone aggregate 40mm nominal size), inside and outside plastering 12mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished with a floating coat of neat cement inside and rough plaster on outside, including fixing of grating , neatly finished with 2 nos.manhole cover complete in all respects including necessary excavation, refilling and disposal of surplus earth, complete as per approved drawing. .

Providing and laying Non Pressure NP-3 class (Medium duty) R.C.C.pipes including collars/spigot jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete (For Road Crossing) 450mm dia RCC Pipe

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, up to 90 metre depth below ground level. All Types of Soil 350mm dia

Providing & fixing 200 mm dia. uPVC housing pipe 8Kg/Cm sq confirming to IS 12818 complete as per direction of engineers charges.

Providing & fixing 200 mm dia. uPVC Slotted pipe 8Kg/Cm sq confirming to IS 12818omplete as per direction of engineers charges.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing 200 mm dia. screw cap made out of PVC plate of sound construction locking arrangement. 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I). 200 mm dia

Supplying and fixing 80 mm dia. pipe class B ISI marked ncluding all accessories and fittings required for installation of pump.

Supplying & installation submersible pumping motor pumpsets ISI marked of approved make Kirloskar, KSB, etc., equivalent, making connection suitable for tube-well/D.C.B. The job includes screwing and welding of flanges on G.I. riser pipes (65 mm dia minimum) installation, complete fittings accessories with riser pipes jointing of electrical cables other connections making switch board electrical connections, all labour for testing of submersible pump and supply of water to water mains complete in all respects, 7.5 H.P app. motor having discharging capacity 12 to 15 cum/hour against a head of 120 metres.

SOIL RETENTION AND SLOPE PROTECTION Providing and laying of Shotcreting with designed mix cement concrete M35 with theoritical thickness as shown on design drawings, in technical specifications and as directed by engineer-in-charge. The rate shall include sprayed concrete of M35, all concrete additives, accelerators etc, wastage of sprayed concrete, rebound, application of shotcrete in multiple layers, all auxiliary materials amd works, all labour, cement, materials, cost of pins, hooks, lead, lift, handling complete with contractor's own equipment for complete job as per specifications and as directed by Engineer-in-Charge. Measurement and payment shall be as per actual work done on surface area as shown on the design drawing in squre meters or cubic meters. Preparing numerical analysis and design of slope retention system using input parameters viz. pull out tests values, various physical and shear parameters from geotecnical investigation report.including preparation of construction drawings, detalied specification, construction methodology, material specification etc. 100 mm thick

200 mm thick

Supply and placement of welded wire mesh 150 x 150 x 6 as reinforcement of sprayed concrete for slope works as shown on design drawings, specifications or as directed by Engineer. Steel grade minimum Fe 500. This item also includes: - Fixing elements and materials - cutting, bending and placement - all auxiliary materials and works necessary The rates shall include all labour, materials, cost of pins, hooks, lead, lift handling, wastage complete with contractor's own equipment for complete job as per specifications and as directed by Engineer-in-charge. Measurement and payment shall be of the weight for each layer installed and instructed, measured along slope. Overlapping as mentioned in technical specifications is mandatory but shall not be paid extra.

Supply, drilling, installation, grouting and testing of 25 mm dia SN type rock bolts of 6 m length, 200kN minimum breaking load as per design drawings, technical specifications or as directed by engineer. Measurement and payment shall be as per piece tested and accepted installed rock bolt (total length). Note: any change in length of Rockbolts, amount shall be added or reduced as per equivalent length calculated upon.

Supply, drilling, installation, grouting and testing of 32 mm dia Self Driilling Rock bolts of 6 m length, 200kN minimum breaking load as per design drawings, technical specifications or as directed by engineer. Drilling with grout flushing is mandatory. This item includes couplings, sacrifiable drilling bits and grouting. Measurement and payment shall be per piece tested and accepted installed rock bolt (total length). Note: any change in length of Rockbolts, amount shall be added or reduced as per equivalent length calculated upon.

Desing, providing drawings and installation of galvanised Fe 600 bars as per IS 1786:2008 and minimum galvanization of 500 grams per sqm required for construction of reinforced slopes steepened slope composite structure including supply of 25/32 mm dia. soil nails , galvanized nail plates, dome shape nuts, coupler (if required), mechanical connection device for direct link between the soil nail and reinforced soil structure, galvanized welded backmesh of 8 mm dia., including drilling in soil, hard and soft rock, grouting using cement and non-shrink grout admixtures etc. including all men, machines, lead and lifts as per detailed specification.

Drilling inside the slope, supply and installation of 100 mm dia. semi-perforated drain pipe wrapped with non-woven geotextile as per detailed design and drawing.

Design, providing construction drawings, providing methodology for construction of reinforced Soil Slopes structures as per BS 8006:2010, FHWA NHI-10-024 (2009), supply of High Density Polythelene geogrids has to be as per FHWA Section 2.4.4 (No PET coated grid allowed to be used), including steel mesh facia (made from minimum 8mm diameter bars) , non-woven coir geotextile as per MORT&H Table 700-15(if any as per approved drawings) as per the technical specification of FHWA Reinforced Soil Structures including installation. This item has to be done by appointing a specialized agency meeting the eligibility criteria as mentioned in the technical specification. Wherever, the available space is not adequate for laying the soil reinforcement , the soil reinforcement shall be mechanically connected with soil nail to form Reinforced slope composite structure including design and drawing to be vetted by NIT/IIT Roorkee for all sections and drawings.

Providing and laying in position cement concrete of 1:3:6 (1 cement : 3 sand : 6 graded stone aggregate 20mm nominal size) proportion excluding cost of cement, centering and shuttering - All works upto bench or berm level :

Providing and laying of vegetative soil in front of the Reinforced slope facia (average thickness 300mm) as per technical specification and drawing.

Providing & Laying of a Permeable geotextile filter between pitching and embankment slopes on which pitching is laid to prevent escape of the embankment material through the voids of the stone pitching/cement concrete blocks as well as to allow free movement of water without creating any uplift head on the pitching. as per MORT&H Table 700-1 guide lines (For moderate conditions)

Supplying & laying of drainage geocomposites as per IRC SP 59:2019 , supplied in the form of roll for easy transportation to site of work as per detailed specification all complete as per directions of Engineer in charge

Supplying and placing of perforated pipes as per IS 9271: 2004 to be used as horizontal internal drains as per drawings and detailed technical specification including manpower, tools, tacles, all complete as per specification.

Supplying and laying of geosynthetic clay liners for the berms (if any) as per the technical specification including manpower, tools, tackles, all complete as per technical specifications, including overlaps as per the Engineer - in- Charge..

Providing and laying of clean, free draining, granular with high friction and non-cohesive, non corrosive, coarse grained as per Table 3-1 / Table 3-2 of FHWA NHI-10-024, free of any deleterious matter, chlorides, salts, acids, alkalies, mineral oil, fungus and microbes and shall be of specidied PH value, meeting the design parameters in layers in solid reinforced zone including tranporting, dumping, spreading, compaction in layers including all manpower, machinery, field test with all labour and material complete as per drawing and technical specifications.

Making bore holes of 100 -150mm dia below existing soil ground surface upto minimum 25 m depth or as required by auger drilling as per IS 1892 – 1979 through all type of soils or refusal strata whichever occurs earlier ( Refusal strata shall mean when SPT field ‘N’ value reaches 100 for 30 cm or less penetration of SPT sampler) and recording SPT, Collection of all samples etc for testing as per IS specification etc complete. This item includes 5 bore holes of 20 m depth or till refusal.

Laboratory Test, Conducting laboratory test on UDS/DS sample as per relevant IS code. Liquid & plastic Limits

Grain Size analysis

Hydrometer analysis

Tri-axial shear test (UUT)

Direct shear test

Consolidation test on clayey soil

Bulk & dry density

Natural Moisture Content

Specific gravity

LIFTS Academic Block-1: 20 Pax, Speed- 1.5 m/sec, Stops- 03, Shaft size- 2740 x 2400 mm

Academic Block-2: 20 Pax, Speed- 1.5 m/sec, Stops- 03, Shaft size- 2740 x 2400 mm

Academic Block-3: 20 Pax, Speed- 1.5 m/sec, Stops- 03, Shaft size- 2740 x 2400 mm

Girls Intern: 13 Pax, Speed- 1.5 m/sec, Stops- 03, Shaft size- 2050 x 2520 mm

Girls Hostel: 13 Pax, Speed- 1.5 m/sec, Stops- 03, Shaft size- 2650 x 1900 mm

Boys Intern: 13 Pax, Speed- 1.5 m/sec, Stops- 03, Shaft size- 2050 x 2520 mm

Boys Hostel: 13 Pax, Speed- 1.5 m/sec, Stops- 03, Shaft size- 2650 x 1900 mm

Sr. Residents: 13 Pax, Speed- 1.5 m/sec, Stops- 03, Shaft size- 1900 x 2400 mm

Sr. Residents: 10 Pax, Speed- 1.5 m/sec, Stops- 03, Shaft size- 1900 x 1700 mm

Jr. Residents: 13 Pax, Speed- 1.5 m/sec, Stops- 03, Shaft size- 2050 x 2520 mm

Nurse Hostel: 13 Pax, Speed- 1.5 m/sec, Stops- 03, Shaft size- 1900 x 2400 mm

Nurse Hostel: 10 Pax, Speed- 1.5 m/sec, Stops- 03, Shaft size- 1900 x 1700 mm

Type-III: 20 Pax, Speed- 1.5 m/sec, Stops- 03, Shaft size- 2300 x 3000 mm

Type-III: 16 Pax, Speed- 1.5 m/sec, Stops- 03, Shaft size- 2100 x 2500 mm

Type-IV: 20 Pax, Speed- 1.5 m/sec, Stops- 03, Shaft size- 2300 x 3000 mm

Type-V: 10 Pax, Speed- 1.5 m/sec, Stops- 02, Shaft size- 1900 x 2300 mm

IPD Block-I: 22 Pax, Passenger cum Bed, Speed- 1.5 m/sec, Stops- 03, Shaft size- 2620 x 3000 mm

IPD Block-II: 22 Pax, Passenger cum Bed, Speed- 1.5 m/sec, Stops- 03, Shaft size- 2620 x 3000 mm

OPD Block: 22 Pax, Passenger cum Bed, Speed- 1.5 m/sec, Stops- 03, Shaft size- 2250 x 3000 mm

SIGNAGES "Signage made of 3D channel Latter, made from Following Front :- Front made of 3mm Acrylic. Side :- Signage made of CNC channel bending machine made of exturded alloy 6063 thickness of 1.00mm confirming to BS 1474-1987 . Having width 127 of Various size front edge and border with provisioning of housing front Acrylic inside . Back of the extrusion must be provided with built in weather proof layer to prevent dust , moisture etc. Alloy to be anodize to 18to 20 microns in silver finish. illumination :- Signage is to be illuminated with LED module base LED made of samsung ( with IP67 grade power supplies) Back :- latter is to be made of 4mm white ACP with 0.5 thickness foile. MAKE- 247 sign/ ASB Ads/ Glo-Lite size- 21525 x 900mm

A) INTERNAL Frame – Fabricated out of 100mm ISMC with Cross Supports of 37x37mm MS SHS . Structure shall be duly surface treated with primer & Paint. B)Corner Profiles - SiSignage made on CNC channel bending machine made of extruded alloy 6063 with thickness of 0.9mm grade 6063 alloy confirming to B.S. 1474-1987. Front edge/border with provisioning of housing front acrylic inside. built in weather proof layer to prevent dust, moisture and etc. Alloy to be anodized to 18 to 20 microns in silver finish. Test certificate for alloy is must be attached with tender for side profile. Certificate of anodizing must be attached with the tender for side profile. Design and a sample of Size 6 Running inch, Side profile must be attached with the tender. Side Make- 247 SIGN / AAA Business solution / Geolite C) ACP Cladding - Front & Back shall be cladded with ACP of approved color Make- 4 mm having .5mm aluminium , duly housed in the corner profiles. Text & pictographs to be in translucent vinyle. D) Logo+ Motif: 3d Letters with 10mm acraylic raising in desired shade. E)Sides :- Sides of the totem to have white / approved colour illumination flowing. F) Illumination : The Lighting for Sides shall be achieved through Samsung make LEDS and IP 67 Grade powersupply, 3 years warrantee from the supplier to be provided. G) Base Plate : Base Plate of size 400x400 mm twin plates of thickness 10 mm is to be used. H)Foundation: Foundation of totem shall be RCC of size 300x450x900mm 2 nos. with 25mm Directional Totem, size- 900 x 2400mm

POST :- Signage is to be made of 100x100 mm SS 304 grade pole. Panel :- Signage is to be made of 4mm exterior grade ACP+ 3m vinyle at top pannel with Dubble ACP and acrylic. illumination:- illumination to be done by Samsung LED Modules. Base plate :- Base plate is to be provided in SS 304 grade grouted with SS Bolt. AS/design RCC Foundation to be done by Client. Panel

A) INTERNAL Frame –Internal Frame made of 19X19mm MS SHS pipe for Supports. B) ACP Cladding - Front & Back shall be cladded with ACP 4mm thick. 0.5 Aluminium foil. C) Text + Pictograph :Text + Pictograph to be made of Retroreflective. D) Pole- 1500 Height MS powder coated 100mm SHS pole for fixed on it. E) Base Plate : Base Plate of size 200x200mm of thickness 10mm is to be used. F)Foundation: Foundation of totem to be done by client. Drop off/ Speed Limit / No Horn/ BASEMENT Entry/Exit, size- 450 x 1500mm

Made out of powdercoated Aluminium box to match PANTONE 354C & 040 acrylic cap with 3M vinyl matching pasted on top with reverse cut letters and fixing provision at back with Samsung LED for illumination sized 450mm x300mm in, size- 450 x 300mm

out, size- 450 300mm

Emergency Evacuation Signage :- Signages made of Single Layer ACP (3mm) with 90* edges and no border.Photoluminicent to be covered with print on 3M clear vinyl with Gloss Lamination for extra durability. Stair Direction at landing, size- 300x125mm

Stair No, size- 400x125mm

Stair Floor Level Indicator, size- 382x382mm

Fire Safety Disclaimer, size- 300x300

FHC, size- 150 x200mm

Fire alarm, size- 150 x200mm

Fire Exit, 600x 175mm

Evacuation Plan A2, 420 x 514mm

Evacuation Plan A3, size- 297x420mm

Emergency Evacuation signage ( Battery backup ) ITEM Name:-Edge Lit Emergency Signage MODEL - EMEX3726- Premium Casing:-Anodised Aluminium with Plastic / Metal Side Caps. Signages Over all size :-375 x 260 mm Text Panel:-8 mm Acrylic Back Up Duration :- 180 Minutes Primary Power Source:-AC - 150-240 Volt Luminarre:-LED Battery Disconection Swith :- Yes Battery Capacity:- 2000 AMH Battery Type:- Lithium ION- New AC to DC Built in Adaptor:- Yes Fuse for Circuit protection:-Yes AC, Charging, EMERGENCY Indicators:-Yes Emergency Test Switch:-Yes Battery Minimum Discharge Protection :- Yes Battery Maximum Charge Protection:- Yes MAKE- 247 sign/ ASB Ads/ Glo-Lite Installation:- In client scope BB Directional, size- 375x260mm

BB Exit, size- 375x260mm

Signage made of S.S. 304 grade 1 mm thickness text to be engrave on it. Lift No, size- 200x85mm

No smoking / No littering, size- 300x400mm

LIFT LOBBY, size- 400x125mm

Signage made of S.S. 304 grade 1 mm thickness text to be engrave on it. Floor level indicator lift, size- 250x250mm

Signage made of extruded grade 6063 alloy confirming to B.S. 1474-1987. . Front edge/border of 2mm width with provisioning of housing front print inside. Fixing arrangment made of anodised aluminium to be done on back and sides . Alloy to be anodized to 18 to 20 microns in silver finish.With aluminium Anodised side caps with 3 mm Thickness. Test certificate for alloy is must be attached with tender for aluminium Profile. Certificate of anodizing must be attached with the tender for side profile. Design and a sample of Size 6 Running inch, Side profile must be attached with the tender. MAKE- 247 sign/ ASB Ads/ Glo-Lite Room indentification, size- 450x156mm

Department indentification, size- 650x200mm

Wash room ( Wall mounted ), size- 156x156mm

Wash room ( Wall Projected), size- 250x250mm

Floor directory, size- 600x1500mm

ROOM NO, size- 156x156

Wayfinding - Signage is to be made of 5mm acrylic with vinyl plotter cut names - Double side with SS suspension fixtures. WAY FINDING 2 WAY, size- 1200x500mm

Poster frame made of anodised aluminium, clip on arrangement for easy change of insert. Use clear acrylic as a protection layer in the front. A3, size- 297x420mm

A2, size- 420x514mm

3M Retro-reflective vinyl graphics pasted on 18 gauge 600mm x 900mm MS sheet mounted to existing light poles with two C-clamp provision. Car parking, size- 600x 900mm

Furniture Providing and placing HNI Make "Trent" , Main Table 1500 x 750mm, completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table of size 750mm L x470mm D x725mm Ht with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Doctor table IPD-1 FURNITURE WORKS

Providing and supplying HNI Model Quip High Back Chair with head rest .This is a High back chair with Mesh Back with back tilt tension adjustable . The chair mesh is available in 6 different colours ( Green / Ruby / Cinnamon / Magenta / Indigo / Black ) with matching or contrast seat fabric according to the choice of the client..The chair has Adjustable Lumber Support . The Chair has Nylon base with 60 mm twin wheel castors .Chair has 1-D adjustable armrests . Seat size is 490 mm W x 435 mm D and the Chair Height 1135mm - 1225mm . Overall size of the chair is 640mm W x 665mm D x (985 mm- 1220mm) H . The PU foam used for chair seat is fire retardant .The chair has Pneumatic Gas Lift with Stroke=85 mm . Chair carries a warranty of 5 years. Main Chair

Providing and fixing HNI Model Gail . Medium Back Mesh Chair with Lumber Support, Seat Size 510mm W x 510mm D, Back Size 480m W x 520mm Ht . The chair comes with PP arms , Nylon base with 50mm castors . The chair has Push Back Mechanism .The chair comes with Pneumatic Gas Lift of Stroke=95 mm . Seat Height Minimum 480mm from Ground and Maximum 570mm. Overall size of the chair is 620 mm W x 680 mm D x (950 mm- 1050mm) H .The Chair Warranty : 3 Years. Visitor Chair

Providing & Fixing of sofa . the inside frame is made of seasoned wood and has antitermite treatment. The seat and back are made of foam and is finished in leatherite upholestry. The structure is supported on Polished Solid Wood Legs. Leatherite colour and type as per directions of Engineer in Charge. The above furniture should be as per specification and sample approved by client. 2 Seater Sofa

4b) 1 Seater Sofa Providing & Fixing of sofa . the inside frame is made of seasoned wood and has antitermite treatment. The seat and back are made of foam and is finished in leatherite upholestry. The structure is supported on Polished Solid Wood Legs. Leatherite colour and type as per directions of Engineer in Charge. The above furniture should be as per specification and sample approved by client.

Single Bed Providing & Placing Bed of size 2000 mm x 900mm The top of the bed is 18 mm thick ISI marked Pre-laminated Board, grade conforming to IS:12406 fixed on 19mm x19mm cross stiffeners frame. The 3 sides of the bed to be in 50x25mm MS Tubes and cladded with 18 mm thick Pre-laminated board , conforming to IS:12406 . The head & Foot rest to be as per drawing in 18mm Pre-laminated board conforming to IS:12406 to achieve shape and design. The bed has four legs made out of 50x25x1.6mm thk MS tubes. Decorative Teak Wood Lipping is provided on all the edges of bed. All Metal Parts is Duly Powder Coated with 45 microns.(Without Matress)

Bed Side Table HNI Make Corner Table having dimension 500mm L x 500mm W x 400mm H with completely made of 25mm thick prelaminated particle board . Verticals also made of 25mm Particle board. All edges are sealed with 2 mm thick PVC Lipping. 25mm thick particle board Top with edges sealed with PVC lipping. 25mm thick particle board Gable ends with edges sealed with PVC lipping. 18mm thick particle board Modesty panel with edges sealed with PVC lipping. 0-20mm adjustable levelers.

Almirah Providing & Supplying Cabinet . It shall have dimensions 900mm (W) x 1660 mm (H) x 450 mm (D) and shall be made of prime Quality CRCA 0.8mm thk for all the body panels and shelves having top & bottom stiffeners in 0.8mm CRCA steel.. Shelves are adjustable in variable heights and shall have Uniformly Distributed Load capacity of 50 Kg per shelf . The vertical sides of storages from inside have contineous slots for mounting variable height shelves. Complete carcass is finished with Epoxy polyester powder coating finish 50 +/-10 microns 2)Facia : The cabinet shutters are made of Metal 3)Handles : Handle Shall be aesthetically designed D handles in SS finish. 4) Locking Mechanism: Locking Mechanism shall be Cam lock in Metal Door. 5)Levellor: It also have adjustable Leveler with plastic base with height adjustment up to 15mm. The above furniture should be as per specification and sample approved by client.

Canteen Table a) 1650mm l x 750mm W x 750mm Ht Providing & Fixing of Cafe table . The Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of powdered coated steel 50mmx 50mm Section. Cross Member are in CRCA steel and the Beam is made of MSof 1.5mm thickness in powder coated finish of 50 microns thickness . The above furniture should be as per specification and sample approved by client.

Canteen Table b) 1650mm l x 600mm W x 750mm Ht Providing & Fixing of Cafe table . The Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of powdered coated steel 50mmx 50mm Section. Cross Member are in CRCA steel and the Beam is made of MSof 1.5mm thickness in powder coated finish of 50 microns thickness . The above furniture should be as per specification and sample approved by client.

Café ChairModel no: MANTO•Back Finish - Plastic Shell (Red , Orange and Blue colour) •Seat Finish - Plastic Shell (Red , Orange and Blue colour) •Base Type -Sledge base, powder-coated in Silver color. •Stackability - up to 6- high on the floor. Seat size - 446 W X 430 D , back height (From Seat to Top of Back Frame) is 410mm . The chair comes with sledge base of size 500 W x 490 D

Waiting Area SofaProviding and Supplying HNI Metal Waiting chair Model ES 909 - 3 Seater made of Metal Powder coated Seat Frames supported on Steel Beams. Seat and Back are single piece duly powder coated. Dimension - 1770mm L x 790mm H x 600mm D . Legs and Armrests are in Chrome plated Finish. ACADEMIC- 1

Dir. & CAO Cabin Room-a) Main Table :-W1800xD750xH750mm Providing and Placing HNI make Cabin Table "STELLAR" . Main Table and Side Table made of 36 mm thick Pre Laminated Particle Board with matching 2 mm thick edge Banding. Modesty panels are in 18mm thk Postlaminated finish. Table supports are combination of Metal poles and Gable ends. Access Flap with Cable tray and switch mounting plate is provided on side table for wire management. Back storage unit Combination of Hinged Door unit and has Tower Assembly with Glass Shelves on top of Hinged Door Unit. Back Unit and Tower unit are made of Prelaminated particle Board 18mm thick with Matching PVC lipping. SS handles 220mm L are provided in storages. 3 drawer pedestal unit has castors and pedestal unit is made up of 18mm thk. Prelaminated Particle Board Caracass having central locking system . 2 Drawers are with roller slide mechanism and Filing Unit is with Ball bearing slides.

Dir. & CAO Cabin Room-b) Side Return :-W1500xD450xH750mm Providing and Placing HNI make Cabin Table "STELLAR" . Main Table and Side Table made of 36 mm thick Pre Laminated Particle Board with matching 2 mm thick edge Banding. Modesty panels are in 18mm thk Postlaminated finish. Table supports are combination of Metal poles and Gable ends. Access Flap with Cable tray and switch mounting plate is provided on side table for wire management. Back storage unit Combination of Hinged Door unit and has Tower Assembly with Glass Shelves on top of Hinged Door Unit. Back Unit and Tower unit are made of Prelaminated particle Board 18mm thick with Matching PVC lipping. SS handles 220mm L are provided in storages. 3 drawer pedestal unit has castors and pedestal unit is made up of 18mm thk. Prelaminated Particle Board Caracass having central locking system . 2 Drawers are with roller slide mechanism and Filing Unit is with Ball bearing slides.

Dir. & CAO Cabin Room-c) Back Storage :-W1800xD450xH1800 mmProviding and Placing HNI make Cabin Table "STELLAR" . Main Table and Side Table made of 36 mm thick Pre Laminated Particle Board with matching 2 mm thick edge Banding. Modesty panels are in 18mm thk Postlaminated finish. Table supports are combination of Metal poles and Gable ends. Access Flap with Cable tray and switch mounting plate is provided on side table for wire management. Back storage unit Combination of Hinged Door unit and has Tower Assembly with Glass Shelves on top of Hinged Door Unit. Back Unit and Tower unit are made of Prelaminated particle Board 18mm thick with Matching PVC lipping. SS handles 220mm L are provided in storages. 3 drawer pedestal unit has castors and pedestal unit is made up of 18mm thk. Prelaminated Particle Board Caracass having central locking system . 2 Drawers are with roller slide mechanism and Filing Unit is with Ball bearing slides.

b) Side Return :-W1500xD450xH750mmMain ChairVerta HB with Headrest High Back W/ Headrest Fabric Upholstered & Leatherite Upholstered Weight activated synchronize w/ Seat Depth Adj 4D Adj. Black PU Armrests 4D With Lumbar Support Adjustment Black Back Frame Black Y Support Polished Aluminium Base 380 Imitation Leather 380 WARRANTY: 10 Years from the date of invoice

Visitor Chair- Providing and supplying HNI Model Ativo Medium Back Chair with Curvature Backrest.The curvature Corresponds to natural curves of spine and supports lumber assuring supreme comfort and no upper - body strains. This is a Medium back chair with Mesh Back with back tilt tension adjustable . The chair has Adjustable Lumber Support . The Chair has Nylon base with 60 mm twin wheel castors .Chair comes with 1-D adjustable armrests . Seat size is 500 mm W x 515 mm D and the Chair Height 975 mm - 1070 mm . Overall size of the chair is 640mm W x 665mm D x (975 mm- 1070mm) H . The PU foam used for chair seat is fire retardant . The chair has Pneumatic Gas Lift with Stroke=85 mm . . Chair carries a warranty of 5 years.

a) 3 Seater Sofa- Providing & Fixing of sofa . The inside frame is made of seasoned wood and has antitermite treatment. The seat and back are made of foam and is finished in leatherite upholestry. The Frame base has Webbing for Supporting the Cushions. The Complete Sofa Body has Polyurethane Foam in desired shape. The Sofa is supported on Metal Chrome Plated Legs. Leatherite colour and type as per directions of Engineer in Charge.

b) 2 Seater Sofa- Providing & Fixing of sofa . The inside frame is made of seasoned wood and has antitermite treatment. The seat and back are made of foam and is finished in leatherite upholestry. The Frame base has Webbing for Supporting the Cushions. The Complete Sofa Body has Polyurethane Foam in desired shape. The Sofa is supported on Metal Chrome Plated Legs. Leatherite colour and type as per directions of Engineer in Charge.

c) 1 Seater SofaProviding & Fixing of sofa . The inside frame is made of seasoned wood and has antitermite treatment. The seat and back are made of foam and is finished in leatherite upholestry. The Frame base has Webbing for Supporting the Cushions. The Complete Sofa Body has Polyurethane Foam in desired shape. The Sofa is supported on Metal Chrome Plated Legs. Leatherite colour and type as per directions of Engineer in Charge.

Centre Table :-W1200xD600xH400mm-Supply and placing centre table in position with sizes with top made of 10mm thick glass top supported on SS Studs on understructure of Prelaminated Particle Board. The Table shall have another shelf at lower level The work shall be carried out as per the instructions received from engineer-incharge.

Providing & Fixing of Table made of 18mm thick prelaminated particle board .The top is 10mm thick Glass supported on 4 nos. SS Studs with verticals also made of 18mm Particle board.The table has a shelf of 450mm L x 450mm W under the main top. All edges are sealed with 2 mm thick PVC Lipping. The above furniture should be as per specification and sample approved by client.a) Corner Table :-W450xD600xH400mm

Providing & Fixing of Table made of 18mm thick prelaminated particle board .The top is 10mm thick Glass supported on 4 nos. SS Studs with verticals also made of 18mm Particle board.The table has a shelf of 450mm L x 450mm W under the main top. All edges are sealed with 2 mm thick PVC Lipping. The above furniture should be as per specification and sample approved by client.b) Corner Table :-W600xD600xH400mm

FA Cabin RoomProviding and placing HNI make PIINACLE cabin table ,Main Table is made up of 25mm thk. Prelaminated particle Board with 2mm PVC Edge Banding supported on Gable ends made out of 25mm thk prelam particle boards with 2mm thk PVC edge banding. Modesty panels is in 18mm thk Prelaminated finish. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. Wire routing / wire management groumets shall be provided on main Table. Side Table is made up of 25mm thick Prelaminated particle Board with 2mm PVC Edge Banding supported on Gable ends made out of 25mm thk prelam particle boards with 2mm thk PVC edge banding and laminate credenza unit . Modesty panels are in 18mm thk Prelaminated Particle finish. Main Table has laminate Pedestal unit made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823. The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from a) Main Table :-W2400xD750xH750mm

FA Cabin RoomProviding and placing HNI make PIINACLE cabin table ,Main Table is made up of 25mm thk. Prelaminated particle Board with 2mm PVC Edge Banding supported on Gable ends made out of 25mm thk prelam particle boards with 2mm thk PVC edge banding. Modesty panels is in 18mm thk Prelaminated finish. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. Wire routing / wire management groumets shall be provided on main Table. Side Table is made up of 25mm thick Prelaminated particle Board with 2mm PVC Edge Banding supported on Gable ends made out of 25mm thk prelam particle boards with 2mm thk PVC edge banding and laminate credenza unit . Modesty panels are in 18mm thk Prelaminated Particle finish. Main Table has laminate Pedestal unit made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823. The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from b) Back Storage :-W4050xD450xH750mm

Providing and supplying HNI Model Ativo High Back Chair with head rest with Curvature Backrest.The curvature Corresponds to natural curves of spine and supports lumber assuring supreme comfort and no upper - body strains.This is a High back chair with Mesh Back with back tilt tension adjustable . The chair has Adjustable Lumber Support . The Chair has Nylon base with 60 mm twin wheel castors .Chair has 1-D adjustable armrests . Seat size is 500 mm W x 515 mm D and the Chair Height 1135mm - 1225mm . Overall size of the chair is 640mm W x 665mm D x (985 mm- 1220mm) H . The PU foam used for chair seat is fire retardant . The chair has Pneumatic Gas Lift with Stroke=85 mm . Chair carries a warranty of 5 years.Main Chair

Visitor ChairProviding and supplying HNI Model Certo Medium Back Chair .This is a Medium back chair with Mesh Back with back tilt tension adjustable . The chair has Anchored Lumber Support . The Chair has Nylon base with 50 mm twin wheel castors .Chair comes with 1-D adjustable PP armrests . Seat size is 500 mm W x 520 mm D and the Chair Height 985 mm - 1080 mm . Overall size of the chair is 635mm W x 605 mm D x (985 mm- 1080mm) H . The PU foam used for chair seat is fire retardant . The chair has Pneumatic Gas Lift with Stroke=85 mm .

a) 3 Seater SofaProviding & Fixing of sofa . the inside frame is made of seasoned wood and has antitermite treatment. The seat and back are made of foam and is finished in leatherite upholestry. The structure is supported on Polished Solid Wood Legs. Leatherite colour and type as per directions of Engineer in Charge. The above furniture should be as per specification and sample approved by client.

Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors. SR. OFFICER , CONTROLLER EXAMa) Main Table :-W1800xD750xH750mm

b) Side Return :-W1200xD450xH750mmProviding and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

c) Back Storage :-W2250xD450xH750mmProviding and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

a) Centre Table :-W800xD800xH400mmHNI make centre table with completely made of 25mm thick prelaminated particle. The Table have one pull out drawer and another shelf at lower level. 25mm thick particle board Top with edges sealed with PVC lipping. 25mm thick particle board Gable ends with edges sealed with PVC lipping. 18mm thick particle board Modesty panel with edges sealed with PVC lipping. 0-20mm adjustable levelers. 1 Drawer.

b) Centre Table :-W1200xD600xH400mmHNI make centre table with completely made of 25mm thick prelaminated particle. The Table have one pull out drawer and another shelf at lower level. 25mm thick particle board Top with edges sealed with PVC lipping. 25mm thick particle board Gable ends with edges sealed with PVC lipping. 18mm thick particle board Modesty panel with edges sealed with PVC lipping. 0-20mm adjustable levelers. 1 Drawer.

Corner Table :-W600xD600xH400mmHNI Make Corner Table having with completely made of 25mm thick prelaminated particle board . Verticals also made of 25mm Particle board. All edges are sealed with 2 mm thick PVC Lipping. 25mm thick particle board Top with edges sealed with PVC lipping. 25mm thick particle board Gable ends with edges sealed with PVC lipping. 18mm thick particle board Modesty panel with edges sealed with PVC lipping. 0-20mm adjustable levelers.

Cabin TablesProviding and placing HNI Make "Trent" , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table of size mentioned above with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit.a) Main Table :-W1500xD750xH750mm includes pedestal

Cabin TablesProviding and placing HNI Make "Trent" , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table of size mentioned above with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit.b) Side Return :-W900xD450xH750mm

Cabin TablesProviding and placing HNI Make "Trent" , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table of size mentioned above with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit.c) Back Storage :-W2400xD450xH750mm

PS Room , REC.Providing and placing HNI "Winner" , Table completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. The Table has Built in 1 Door Pull Out Unit with lock and handle.b) Main Table :-W1500xD600xH750mm

PS Room , REC.Providing and placing HNI "Winner" , Table completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. The Table has Built in 1 Door Pull Out Unit with lock and handle.c) Back Storage :-W1200xD450xH750mm

Providing and placing HNI "Winner" , Table completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. The Table has Built in 1 Door Pull Out Unit with lock and handle. c) Back Storage :-W1200xD450xH750mm

Providing and fixing HNI Model Gale . Medium Back Mesh Chair with Lumber Support, Seat Size 510mm W x 510mm D, Back Size 480m W x 520mm Ht . The chair comes with PP arms , Nylon base with 50mm castors . The chair has Push Back Mechanism .The chair comes with Pneumatic Gas Lift of Stroke=95 mm . Seat Height Minimum 480mm from Ground and Maximum 570mm. Overall size of the chair is 620 mm W x 680 mm D x (950 mm- 1050mm) H .The Chair Warranty : 3 Years.Main Chair

Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors. a) Main Table :-W1500xD750xH750mm includes pedestal

Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors. b) Side Return :-W900xD450xH750mm

Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors. c) Back Storage :-W2200xD450xH750mm

Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors. d) Back Storage :-W2300xD450xH750mm

Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors. e) Back Storage :-W2650xD450xH750mm

Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors. g) Back Storage :-W3250xD450xH750mm

Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors. h) Back Storage :-W3400xD450xH750mm

Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors. i) Back Storage :-W3500xD450xH750mm

Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors. j) Back Storage :-W3550xD450xH750mm

Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors. k) Back Storage :-W3600xD450xH750mm

Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors. l) Back Storage :-W3800xD450xH750mm

Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors. m) Back Storage :-W3850xD450xH750mm

Providing and supplying HNI Model Ativo High Back Chair with head rest with Curvature Backrest.The curvature Corresponds to natural curves of spine and supports lumber assuring supreme comfort and no upper - body strains.This is a High back chair with Mesh Back with back tilt tension adjustable . The chair has Adjustable Lumber Support . The Chair has Nylon base with 60 mm twin wheel castors .Chair has 1-D adjustable armrests . Seat size is 500 mm W x 515 mm D and the Chair Height 1135mm - 1225mm . Overall size of the chair is 640mm W x 665mm D x (985 mm- 1220mm) H . The PU foam used for chair seat is fire retardant . The chair has Pneumatic Gas Lift with Stroke=85 mm . Chair carries a warranty of 5 years.Main Chair

HNI make centre table with completely made of 25mm thick prelaminated particle. The Table have one pull out drawer and another shelf at lower level. 25mm thick particle board Top with edges sealed with PVC lipping. 25mm thick particle board Gable ends with edges sealed with PVC lipping. 18mm thick particle board Modesty panel with edges sealed with PVC lipping. 0-20mm adjustable levelers. 1 Drawer.Centre Table :-W900xD600xH400mm

WorkstationProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. a) Workstation :-W1200xD600xH1200mm

WorkstationProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. b) Workstation :-W1500xD600xH1200mm

WorkstationProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. c) OFFICE CLERICAL Workstation :-W1350xD600xH750mm

WorkstationProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. d) OFFICE CLERICAL Workstation :-W1500xD600xH750mm

WorkstationProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. e) RESEARCH Workstation :-W3850xD600xH750mm

WorkstationProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. f) RESEARCH Workstation :-W4600xD600xH750mm

WorkstationProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. g) RESEARCH Workstation :-W5150xD600xH750mm

WorkstationProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. h) RESEARCH Workstation :-W5850xD600xH750mm

WorkstationProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. i) RESEARCH Workstation :-W6200xD600xH750mm

WorkstationProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. j) RESEARCH Workstation :-W11650xD600xH750mm

WorkstationProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. k) TEACHING Workstation :-W4600xD600xH750mm

WorkstationProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. l) TEACHING Workstation :-W5750xD600xH750mm

Providing & Fixing of HNI make league plus Libraary Reading table of 750mm Ht. The Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of powdered coated steel 50mmx 50mm Section. Cross Member are in CRCA steel and the Beam is made of MSof 1.5mm thickness in powder coated finish of 50 microns thickness . The above furniture should be as per specification and sample approved by client.Printer Table :-W2700xD600xH750mm

Conference TablesProviding and placing Meeting Room table in "U" Shape . Table Tops – Available in standard modules 1500mm L x 750mm D / 1350mm L x 750mm D / 1200mm L x 750mm D / 1050mm L x 750mm D / 900mm L x 750mm D /750mm L x 750mm D , made of 25mm thick Prelaminated Partlice Board. Understructure – Legs made of 18mm thick Prelaminated Particle Board panels interconnected with 18mm thick pre-laminated modesty panels, with height adjustable levelers to take care of uneven floors. Wire Management – Concealed wire management to take care of basic wiring requirements both horizontally & vertically. Cable Tray is mounted on the inner side of modesty panel for horizontal wire carrying. Vertical wire management is through flexible vertical wire manager at one place . Slots for Mounting Data and Electric Switches and Sockets are provided on Cover Section of Cable Tray. Standard table top height – 750mm. Designed for Flexibility through modular Construction, Provision for easy wire management, Upgradeable / reconfigurable for future needs. Corners are Provided in 25mm thickness . Corners are supported on 63.5mm Painted Metal Pole with Leveller for Height Adjustment. a) Conference :-W5650x2400xD750xH750mm

Conference TablesProviding and placing Meeting Room table in "U" Shape . Table Tops – Available in standard modules 1500mm L x 750mm D / 1350mm L x 750mm D / 1200mm L x 750mm D / 1050mm L x 750mm D / 900mm L x 750mm D /750mm L x 750mm D , made of 25mm thick Prelaminated Partlice Board. Understructure – Legs made of 18mm thick Prelaminated Particle Board panels interconnected with 18mm thick pre-laminated modesty panels, with height adjustable levelers to take care of uneven floors. Wire Management – Concealed wire management to take care of basic wiring requirements both horizontally & vertically. Cable Tray is mounted on the inner side of modesty panel for horizontal wire carrying. Vertical wire management is through flexible vertical wire manager at one place . Slots for Mounting Data and Electric Switches and Sockets are provided on Cover Section of Cable Tray. Standard table top height – 750mm. Designed for Flexibility through modular Construction, Provision for easy wire management, Upgradeable / reconfigurable for future needs. Corners are Provided in 25mm thickness . Corners are supported on 63.5mm Painted Metal Pole with Leveller for Height Adjustment. b) Conference :-W5200x2400xD750xH750mm

Providing & Fixing of HNI "Ensemble " Confetrence table . the Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of Aluminum Extrusion of 1.6mm thickness with aesthically designed elliptical Cover sections . Legs are designed to facilitate wire management . Cross Member are in CRCA steel and the Beam is made of MS and has size 75x50 mm of 1.5mm thickness in powder coated finish of 50 microns thickness and is connected with legs to allow for traversing of wires horizontally. The beam raceway provided with slots for fixing data and electrical switches and sockets for each user under the table. The above furniture should be as per specification and sample approved by client.Meeting Table :-W3200xD900xH750mm

Reception Waiting AreaProviding and supplying Reception Desk . It has 25mm thick Worktop and Gable Ends made of pre Laminated Particle Board sealed with PVC Edge Banding. Front and Modesty Panel are 18mm thick Pre Laminated ParticleBoard Sealed with PVC EdgeBanding.. The Counter Top is 25 mm Thick Postformed ParticleBoard. Unit has One Pull out drawer with Lock and Handle.a) Reception table :-W1500xD750xHx H1185

Reception Waiting AreaProviding and supplying Reception Desk . It has 25mm thick Worktop and Gable Ends made of pre Laminated Particle Board sealed with PVC Edge Banding. Front and Modesty Panel are 18mm thick Pre Laminated ParticleBoard Sealed with PVC EdgeBanding.. The Counter Top is 25 mm Thick Postformed ParticleBoard. Unit has One Pull out drawer with Lock and Handle.b) Reception table :-W2100x1650xD600xH1185

HNI make centre table with completely made of 25mm thick prelaminated particle. The Table have one pull out drawer and another shelf at lower level. 25mm thick particle board Top with edges sealed with PVC lipping. 25mm thick particle board Gable ends with edges sealed with PVC lipping. 18mm thick particle board Modesty panel with edges sealed with PVC lipping. 0-20mm adjustable levelers. 1 Drawer.Centre Table :-W800xD800xH400mm

Store RoomProviding and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.a) Storage :-W 1200 xD450xH 1800

Store RoomProviding and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.b) Storage :-W1800 xD450xH 1800

Store RoomProviding and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.c) Storage :-W2100xD450xH1800

Store RoomProviding and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.d) Storage :-W2400xD450xH 1800

Store RoomProviding and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.e) Storage :-W2550xD450xH 1800

Store RoomProviding and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.f) Storage :-W2900xD450xH 1800

Store RoomProviding and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.g) Storage :-W3150xD450xH 1800

Store RoomProviding and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.h) Storage :-W3450xD450xH 1800

Store RoomProviding and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.i) Storage :-W3750xD450xH 1800

Store RoomProviding and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.j) Storage :-W3800xD450xH 1800

Librarian TableProviding and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors. a) Main Table :-W1800xD900xH750mm

Librarian TableProviding and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors. b) Side Return :-W1200xD450xH750mm

Staff Room- Workstation :-W5250x3750xD600xH750mm- Providing and placing HNI BP Ergo make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

Library Area- Librarain Table :-W1200xD600xH750mm Providing and Supplying Table having Dimension 1200mm L x 600mm W x 750mm Ht. Worktop is made of 25mmthick PLPB of Grade II, Type II conforming to IS:12823: 1990 and having 2mm thick pvc edge lipping, Understructure is made of 18mm thick PLPB of Grade II, Type II conforming to IS:12823: 1990 and having 2mm thick pvc edge lipping. One no Drawer is buil into the table. 5 Year Warranty.

Both Side Book Rack :-W 900x D 594 xH1880mm- Providing & Supplying Liabrary Rack of size 900mm L x 594mm D x 1890mm Ht. The top Panel is Made of CRCA Sheet and side panel is made up of 18mm thick pre laminated particle board of interior grade with laminate on both sides of approved make and shade. The working and non – working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at high temperature. the back panel is made up of CRCA Metal Sheet Duly Powder Coated. Brackets holding the shelf are made up of 2mm thick CRCA. Metal shelfs are made up of 0.8mm thick CRCA powder coated finish as per the directions of Engineer in Charge. The above furniture should be as per specification and sample approved by client.

a) Reading Table :-W1500xD900xH750mm Providing & Fixing of HNI make league plus Libraary Reading table of 750mm Ht. The Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of powdered coated steel 50mmx 50mm Section. Cross Member are in CRCA steel and the Beam is made of MSof 1.5mm thickness in powder coated finish of 50 microns thickness . The above furniture should be as per specification and sample approved by client.

b) Reading Table :-W1800xD900xH750mm- Providing & Fixing of HNI make league plus Libraary Reading table of 750mm Ht. The Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of powdered coated steel 50mmx 50mm Section. Cross Member are in CRCA steel and the Beam is made of MSof 1.5mm thickness in powder coated finish of 50 microns thickness . The above furniture should be as per specification and sample approved by client.

Discussion Table :-W900xD900xH750mm- Providing & Fixing of HNI make league plus Discussion table of 750mm Ht. The Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of powdered coated steel 50mmx 50mm Section. Cross Member are in CRCA steel and the Beam is made of MSof 1.5mm thickness in powder coated finish of 50 microns thickness . The above furniture should be as per specification and sample approved by client.

Centre Table :-W900xD500xH400mm- HNI make centre table with completely made of 25mm thick prelaminated particle. The Table have one pull out drawer and another shelf at lower level. 25mm thick particle board Top with edges sealed with PVC lipping. 25mm thick particle board Gable ends with edges sealed with PVC lipping. 18mm thick particle board Modesty panel with edges sealed with PVC lipping. 0-20mm adjustable levelers. 1 Drawer.

Corner Table :-W500xD500xH400mm- HNI Make Corner Table having with completely made of 25mm thick prelaminated particle board . Verticals also made of 25mm Particle board. All edges are sealed with 2 mm thick PVC Lipping. 25mm thick particle board Top with edges sealed with PVC lipping. 25mm thick particle board Gable ends with edges sealed with PVC lipping. 18mm thick particle board Modesty panel with edges sealed with PVC lipping. 0-20mm adjustable levelers.

Café Chair- Model no: MANTO •Back Finish - Plastic Shell (Red and Blue colour) •Seat Finish - Plastic Shell (Red and Blue colour) •Base Type -Sledge base, powder-coated in Silver color •Stackability - up to 6- high on the floor. Seat size - 446 W X 430 D , back height (From Seat to Top of Back Frame) is 410mm . The chair comes with sledge base of size 500 W x 490 D

Centre Table :-W900xD500xH400mm- HNI make centre table with completely made of 25mm thick prelaminated particle. The Table have one pull out drawer and another shelf at lower level. 25mm thick particle board Top with edges sealed with PVC lipping. 25mm thick particle board Gable ends with edges sealed with PVC lipping. 18mm thick particle board Modesty panel with edges sealed with PVC lipping. 0-20mm adjustable levelers. 1 Drawer.

HEMATOLOGY LAB , AMPHIBIAN LABORATORY , PRACTICAL LAB- Lab Table ;-W6150xD1200xH 1550 mm- Providing and Supplying HNI Lab Table . The Understructure is made of 2mm Thick MS Steel Legs having 50mm x 50mm Cross Section. The Legs are connected by MS Steel beams 50mm x 50mm x 2mm Thickness in cross section. The complete metal structure is Duly powder coated for 40-60 micron thickness. The Height of Top from floor Lever is 900mm. The Top of Lab Table is 18mm Thick Jet Black Granite Stone with Polished Edges on all sides. Neoprene Gasket is Placed on underside of Granite over Metal Under structure. Granite has necessary Holes for Electrical and Plumbing Inlets, Gas Pipe line etc. Both Ends of Lab Table are duly closed with 0.8mm thick CRCA Sheet Metal duly Powder coated to Give Clean appearance to the Lab Table. Providing and Connection of Services like Plumbing, Electrical, Gas etc are not in scope of Lab Table Supplier. Metal Storage – Is made of 0.8mm – 1mm thick CRCA Steel Sheet and is duly Powder coated. It has one number Pull out Unit and one Hinged Door Unit with 2 Doors. Dimension of Metal Storage is 700mm W x 400mm D x 635mm Ht. Wash Basin – Poly Propylene Sink Rectangular having dimension 600mm x 450mm x 300mm Ht . Sink is provided with outlet Nipple and this Assembly has PP Hose Pipe with Nut and PP Bottle Trap.Tap – Each Wash Basin is supplanted with 2 No Water Tap for Both Side Lab Island or 1 No Water Tap for Single Side Lab Island. The Tap is Single Swan Water Tap duly Nickel Chrome Plated.Metal Rack with Wire Management – Metal rack made of CRCA 1mm thick Steel Sheet Duly Powder Coated is Provided above the Granite Top at specified Location as per Drawing. Rack is 650m Height from Table top Level. It has 400m clear space between Table Top and Raceway . Raceway carries Electrical and Data Wiring. It is 150mm High Raceway for Fixing Electrical and Data Switches and Sockets ( Not in Scope of Lab Supplier ). The Shelf Verical is 30mm Thick CRCA Sheet and the Upper Shelf is 18mm thick Shelf. This has provision for fixing LED Tubelight under the Shelf.

Lab Stool- Providing and Supplying Lab Stool with Seat Dia minimum 30 cm. The seat should be made up of 12mm thick hot pressed plywood upholstered with fabric / Leatherite and moulded polyurethane foam. Chair should be on a 4 legged Metal Pipe frame assembly with Height adhustability for seat and is duly powder caoted and provided with gliders as per manufacturer's specifications, drawings & direction of Engineer in charge. The above furniture should be as per specification and sample approved by client.

a) Storage :-W5150xD450xH 1660- Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

b) Storage :-W5500xD450xH 1660 Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

c) Storage :-W5750xD450xH 1660 Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

d) Storage :-W8250xD450xH 1660 Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

e) Storage :-W8700xD450xH 1660 Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

f) Storage :-W9600xD450xH 1660 Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

g) Storage :-W9600xD450xH 1660 Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

h) Storage :-W9750xD450xH 1660 Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

i) Storage :-W12550xD450xH 1660- Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

Demo Room- a) Demo Room Table :-W1800xD600xH750mm Providing & Fixing of HNI make league plus of 750mm Ht. The Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of powdered coated steel 50mmx 50mm Section. Cross Member are in CRCA steel and the Beam is made of MSof 1.5mm thickness in powder coated finish of 50 microns thickness . The above furniture should be as per specification and sample approved by client.

b) Demo Room Table :-W3000xD600xH750mm- Providing & Fixing of HNI make league plus of 750mm Ht. The Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of powdered coated steel 50mmx 50mm Section. Cross Member are in CRCA steel and the Beam is made of MSof 1.5mm thickness in powder coated finish of 50 microns thickness . The above furniture should be as per specification and sample approved by client.

Storage One Side:-W 900 x D 300 x H 1880 mm- Providing & Supplying Liabrary Rack of size 900mm L x 310mm D x 1890mm Ht. The top Panel is Made of CRCA Sheet and side panel is made up of 18mm thick pre laminated particle board of interior grade with laminate on both sides of approved make and shade. The working and non – working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at high temperature. the back panel is made up of CRCA Metal Sheet Duly Powder Coated. Brackets holding the shelf are made up of 2mm thick CRCA. Metal shelfs are made up of 0.8mm thick CRCA powder coated finish as per the directions of Engineer in Charge. The above furniture should be as per specification and sample approved by client.

Meeting Table :-W5450xD1050xH750mm- Providing & Fixing of HNI "Ensemble " Confetrence table . the Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of Aluminum Extrusion of 1.6mm thickness with aesthically designed elliptical Cover sections . Legs are designed to facilitate wire management . Cross Member are in CRCA steel and the Beam is made of MS and has size 75x50 mm of 1.5mm thickness in powder coated finish of 50 microns thickness and is connected with legs to allow for traversing of wires horizontally. The beam raceway provided with slots for fixing data and electrical switches and sockets for each user under the table. The above furniture should be as per specification and sample approved by client.

Record Room- Table :-W3550xD600xH750mm- Providing & Fixing of HNI make league plus of 750mm Ht. The Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of powdered coated steel 50mmx 50mm Section. Cross Member are in CRCA steel and the Beam is made of MSof 1.5mm thickness in powder coated finish of 50 microns thickness . The above furniture should be as per specification and sample approved by client.

ACADEMIC- 2 - PS Room , REC.- a) Main Table :-W1200xD750xH750mm - Providing and Supplying Office Table. Worktop is made of 25mmthick PLPB of Grade II, Type II conforming to IS:12823: 1990 and having 2mm thick pvc edge lipping, Understructure is made of 18mm thick PLPB of Grade II, Type II conforming to IS:12823: 1990 and having 2mm thick pvc edge lipping .Three no Drawer is built into the table. The Drawers have lock and each drawer is provided with Pull out Handle. 5 Year Warranty.

b) Main Table :-W1500xD750xH750mm- Providing and Supplying Office Table. Worktop is made of 25mmthick PLPB of Grade II, Type II conforming to IS:12823: 1990 and having 2mm thick pvc edge lipping, Understructure is made of 18mm thick PLPB of Grade II, Type II conforming to IS:12823: 1990 and having 2mm thick pvc edge lipping .Three no Drawer is built into the table. The Drawers have lock and each drawer is provided with Pull out Handle. 5 Year Warranty.

PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM- a) Main Table :-W1500xD750xH750mm- Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM- b) Side Return :-W900xD450xH750mm- Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM- c) Back Storage :-W1500xD450xH750mm- Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM- d) Back Storage :-W1800xD450xH750mm- Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM- e) Back Storage :-W2100xD450xH750mm- Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM- f) Back Storage :-W2200xD450xH750mm- Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM- g) Back Storage :-W2250xD450xH750mm- Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM- h) Back Storage :-W2400xD450xH750mm- Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM- i) Back Storage :-W2550xD450xH750mm- Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM- j) Back Storage :-W2650xD450xH750mm- Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM- k) Back Storage :-W2700xD450xH750mm- Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM- l) Back Storage :-W2800xD450xH750mm- Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM- m) Back Storage :-W2850xD450xH750mm- Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM- n) Back Storage :-W3000xD450xH750mm- Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM- o) Back Storage :-W3050xD450xH750mm- Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM- p) Back Storage :-W3150xD450xH750mm- Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

q) Back Storage :-W3200xD450xH750mm- Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

a) Centre Table :-W800xD750xH400mm NI make centre table with completely made of 25mm thick prelaminated particle. The Table have one pull out drawer and another shelf at lower level. 25mm thick particle board Top with edges sealed with PVC lipping. 25mm thick particle board Gable ends with edges sealed with PVC lipping. 18mm thick particle board Modesty panel with edges sealed with PVC lipping. 0-20mm adjustable levelers. 1 Drawer.

OFFICE CLERICAL , RESEARCH , TEACHING , NON-TEACHING a) Workstation :-W1500xD600xH1200mm -Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) - Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

OFFICE CLERICAL , RESEARCH , TEACHING , NON-TEACHING b) OFFICE CLERICAL Workstation :-W2100xD600xH750mm -Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) - Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

OFFICE CLERICAL , RESEARCH , TEACHING , NON-TEACHING c) OFFICE CLERICAL Workstation :-W2250xD600xH750mm -Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) - Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

OFFICE CLERICAL , RESEARCH , TEACHING , NON-TEACHING d) OFFICE CLERICAL Workstation :-W4650xD600xH750mm -Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) - Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

OFFICE CLERICAL , RESEARCH , TEACHING , NON-TEACHING e) OFFICE CLERICAL Workstation :-W4700xD600xH750mm -Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) - Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

OFFICE CLERICAL , RESEARCH , TEACHING , NON-TEACHING f) OFFICE CLERICAL Workstation :-W5700xD600xH750mm -Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) - Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

OFFICE CLERICAL , RESEARCH , TEACHING , NON-TEACHING g) RESEARCH Workstation :-W3250xD600xH750mm -Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) - Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

OFFICE CLERICAL , RESEARCH , TEACHING , NON-TEACHING h) RESEARCH Workstation :-W3850xD600xH750mm -Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) - Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

OFFICE CLERICAL , RESEARCH , TEACHING , NON-TEACHING i) RESEARCH Workstation :-W4600xD600xH750mm -Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) - Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

OFFICE CLERICAL , RESEARCH , TEACHING , NON-TEACHING j) RESEARCH Workstation :-W4850xD600xH750mm -Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) - Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

OFFICE CLERICAL , RESEARCH , TEACHING , NON-TEACHING k) RESEARCH Workstation :-W5150xD600xH750mm -Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) - Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

OFFICE CLERICAL , RESEARCH , TEACHING , NON-TEACHING l) RESEARCH Workstation :-W7650xD600xH750mm -Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) - Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

OFFICE CLERICAL , RESEARCH , TEACHING , NON-TEACHING m) TEACHING Workstation :-W5750xD600xH750mm -Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) - Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

OFFICE CLERICAL , RESEARCH , TEACHING , NON-TEACHING n) NON-TEACHING Workstation :-W2400xD600xH750mm -Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) - Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

OFFICE CLERICAL , RESEARCH , TEACHING , NON-TEACHING o) NON-TEACHING Workstation :-W2500xD600xH750mm -Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) - Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

OFFICE CLERICAL , RESEARCH , TEACHING , NON-TEACHING p) NON-TEACHING Workstation :-W3150xD600xH750mm -Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) - Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

OFFICE CLERICAL , RESEARCH , TEACHING , NON-TEACHING q) NON-TEACHING Workstation :-W3250xD600xH750mm Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) - Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

OFFICE CLERICAL , RESEARCH , TEACHING , NON-TEACHING r) NON-TEACHING Workstation :-W3850xD600xH750mm Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) - Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side.

b) Reception table :-W1800xD750xH1185 Providing and supplying Reception Desk . It has 25mm thick Worktop and Gable Ends made of pre Laminated Particle Board sealed with PVC Edge Banding. Front and Modesty Panel are 18mm thick Pre Laminated ParticleBoard Sealed with PVC EdgeBanding.. The Counter Top is 25 mm Thick Postformed ParticleBoard. Unit has One Pull out drawer with Lock and Handle.

Centre Table :-W1200xD600xH400mm HNI make centre table with completely made of 25mm thick prelaminated particle. The Table have one pull out drawer and another shelf at lower level. 25mm thick particle board Top with edges sealed with PVC lipping. 25mm thick particle board Gable ends with edges sealed with PVC lipping. 18mm thick particle board Modesty panel with edges sealed with PVC lipping. 0-20mm adjustable levelers. 1 Drawer.

Store Room- a) Storage :-W1500xD450xH1800 Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

Store Room- c) Storage :-W1950xD450xH1800 Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

Store Room- d) Storage :-W2100xD450xH1800 Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

Store Room- e) Storage :-W2400xD450xH1800 Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

Store Room- f) Storage :-W2550xD450xH1800 Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

Store Room- g) Storage :-W2950xD450xH1800 Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

Store Room- h) Storage :-W3050xD450xH1800 Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

Store Room- i) Storage :-W3100xD450xH1800 Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

Store Room- j) RESEARCH Workstation :-W4850xD600xH750mm Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

Store Room-k) Storage :-W3450xD450xH1800 Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

Library Area , DEPARTMENTAL LIBRARY/ SEMINAR - Librarain Table :-W1200xD600xH750mm Providing and Supplying Table having Dimension 1200mm L x 600mm W x 750mm Ht. Worktop is made of 25mmthick PLPB of Grade II, Type II conforming to IS:12823: 1990 and having 2mm thick pvc edge lipping, Understructure is made of 18mm thick PLPB of Grade II, Type II conforming to IS:12823: 1990 and having 2mm thick pvc edge lipping. One no Drawer is buil into the table. 5 Year Warranty.

DEPARTMENTAL LIBRARY/ SEMINAR Table :-W3300xD1200xH750mm - Providing & Fixing of HNI make league plus table of 750mm Ht. The Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of powdered coated steel 50mmx 50mm Section. Cross Member are in CRCA steel and the Beam is made of MSof 1.5mm thickness in powder coated finish of 50 microns thickness . The above furniture should be as per specification and sample approved by client.

Storage Both Side :-W 900 x D 594 x H 1880 mm - Providing & Supplying Liabrary Rack of size 900mm L x 594mm D x 1890mm Ht. The top Panel is Made of CRCA Sheet and side panel is made up of 18mm thick pre laminated particle board of interior grade with laminate on both sides of approved make and shade. The working and non – working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at high temperature. the back panel is made up of CRCA Metal Sheet Duly Powder Coated. Brackets holding the shelf are made up of 2mm thick CRCA. Metal shelfs are made up of 0.8mm thick CRCA powder coated finish as per the directions of Engineer in Charge. The above furniture should be as per specification and sample approved by client.

HEMATOLOGY LAB , AMPHIBIAN LABORATORY , PRACTICAL LAB , HISTOLOGY LAB a) Lab Table ;-W4050xD1200xH1550 Providing and Supplying HNI Lab Table . The Understructure is made of 2mm Thick MS Steel Legs having 50mm x 50mm Cross Section. The Legs are connected by MS Steel beams 50mm x 50mm x 2mm Thickness in cross section. The complete metal structure is Duly powder coated for 40-60 micron thickness. The Height of Top from floor Lever is 900mm. The Top of Lab Table is 18mm Thick Jet Black Granite Stone with Polished Edges on all sides. Neoprene Gasket is Placed on underside of Granite over Metal Under structure. Granite has necessary Holes for Electrical and Plumbing Inlets, Gas Pipe line etc. Both Ends of Lab Table are duly closed with 0.8mm thick CRCA Sheet Metal duly Powder coated to Give Clean appearance to the Lab Table. Providing and Connection of Services like Plumbing, Electrical, Gas etc are not in scope of Lab Table Supplier. Metal Storage – Is made of 0.8mm – 1mm thick CRCA Steel Sheet and is duly Powder coated. It has one number Pull out Unit and one Hinged Door Unit with 2 Doors. Dimension of Metal Storage is 700mm W x 400mm D x 635mm Ht. Wash Basin – Poly Propylene Sink Rectangular having dimension 600mm x 450mm x 300mm Ht . Sink is provided with outlet Nipple and this Assembly has PP Hose Pipe with Nut and PP Bottle Trap. - Tap – Each Wash Basin is supplanted with 2 No Water Tap for Both Side Lab Island or 1 No Water Tap for Single Side Lab Island. The Tap is Single Swan Water Tap duly Nickel Chrome Plated. Chemistry Lab Metal Rack with Wire Management – Metal rack made of CRCA 1mm thick Steel Sheet Duly Powder Coated is Provided above the Granite Top at specified Loaction as per Drawing. Rack is 650m Height from Table top Level and has 2 Levels. Lower Level has 150mm High Raceway for Fixing Electrical and Data Switches and Sockets ( Not in Scope of Lab Supplier ). The Shelf Verical is 30mm Thick CRCA Sheet and the Upper Shelf is 18mm thick Shelf. With Both Levels,Sufficient space for keeping Regents and Chemical Bottles is available.

HEMATOLOGY LAB , AMPHIBIAN LABORATORY , PRACTICAL LAB , HISTOLOGY LAB b) Lab Table ;-W4600xD1200xH1550 Providing and Supplying HNI Lab Table . The Understructure is made of 2mm Thick MS Steel Legs having 50mm x 50mm Cross Section. The Legs are connected by MS Steel beams 50mm x 50mm x 2mm Thickness in cross section. The complete metal structure is Duly powder coated for 40-60 micron thickness. The Height of Top from floor Lever is 900mm. The Top of Lab Table is 18mm Thick Jet Black Granite Stone with Polished Edges on all sides. Neoprene Gasket is Placed on underside of Granite over Metal Under structure. Granite has necessary Holes for Electrical and Plumbing Inlets, Gas Pipe line etc. Both Ends of Lab Table are duly closed with 0.8mm thick CRCA Sheet Metal duly Powder coated to Give Clean appearance to the Lab Table. Providing and Connection of Services like Plumbing, Electrical, Gas etc are not in scope of Lab Table Supplier. Metal Storage – Is made of 0.8mm – 1mm thick CRCA Steel Sheet and is duly Powder coated. It has one number Pull out Unit and one Hinged Door Unit with 2 Doors. Dimension of Metal Storage is 700mm W x 400mm D x 635mm Ht. Wash Basin – Poly Propylene Sink Rectangular having dimension 600mm x 450mm x 300mm Ht . Sink is provided with outlet Nipple and this Assembly has PP Hose Pipe with Nut and PP Bottle Trap. - Tap – Each Wash Basin is supplanted with 2 No Water Tap for Both Side Lab Island or 1 No Water Tap for Single Side Lab Island. The Tap is Single Swan Water Tap duly Nickel Chrome Plated. Chemistry Lab Metal Rack with Wire Management – Metal rack made of CRCA 1mm thick Steel Sheet Duly Powder Coated is Provided above the Granite Top at specified Loaction as per Drawing. Rack is 650m Height from Table top Level and has 2 Levels. Lower Level has 150mm High Raceway for Fixing Electrical and Data Switches and Sockets ( Not in Scope of Lab Supplier ). The Shelf Verical is 30mm Thick CRCA Sheet and the Upper Shelf is 18mm thick Shelf. With Both Levels,Sufficient space for keeping Regents and Chemical Bottles is available.

HEMATOLOGY LAB , AMPHIBIAN LABORATORY , PRACTICAL LAB , HISTOLOGY LAB c) Lab Table ;-W4900xD1200xH1550 Providing and Supplying HNI Lab Table . The Understructure is made of 2mm Thick MS Steel Legs having 50mm x 50mm Cross Section. The Legs are connected by MS Steel beams 50mm x 50mm x 2mm Thickness in cross section. The complete metal structure is Duly powder coated for 40-60 micron thickness. The Height of Top from floor Lever is 900mm. The Top of Lab Table is 18mm Thick Jet Black Granite Stone with Polished Edges on all sides. Neoprene Gasket is Placed on underside of Granite over Metal Under structure. Granite has necessary Holes for Electrical and Plumbing Inlets, Gas Pipe line etc. Both Ends of Lab Table are duly closed with 0.8mm thick CRCA Sheet Metal duly Powder coated to Give Clean appearance to the Lab Table. Providing and Connection of Services like Plumbing, Electrical, Gas etc are not in scope of Lab Table Supplier. Metal Storage – Is made of 0.8mm – 1mm thick CRCA Steel Sheet and is duly Powder coated. It has one number Pull out Unit and one Hinged Door Unit with 2 Doors. Dimension of Metal Storage is 700mm W x 400mm D x 635mm Ht. Wash Basin – Poly Propylene Sink Rectangular having dimension 600mm x 450mm x 300mm Ht . Sink is provided with outlet Nipple and this Assembly has PP Hose Pipe with Nut and PP Bottle Trap. - Tap – Each Wash Basin is supplanted with 2 No Water Tap for Both Side Lab Island or 1 No Water Tap for Single Side Lab Island. The Tap is Single Swan Water Tap duly Nickel Chrome Plated. Chemistry Lab Metal Rack with Wire Management – Metal rack made of CRCA 1mm thick Steel Sheet Duly Powder Coated is Provided above the Granite Top at specified Loaction as per Drawing. Rack is 650m Height from Table top Level and has 2 Levels. Lower Level has 150mm High Raceway for Fixing Electrical and Data Switches and Sockets ( Not in Scope of Lab Supplier ). The Shelf Verical is 30mm Thick CRCA Sheet and the Upper Shelf is 18mm thick Shelf. With Both Levels,Sufficient space for keeping Regents and Chemical Bottles is available.

HEMATOLOGY LAB , AMPHIBIAN LABORATORY , PRACTICAL LAB , HISTOLOGY LAB d) Lab Table ;-W5050xD1200xH1550 Providing and Supplying HNI Lab Table . The Understructure is made of 2mm Thick MS Steel Legs having 50mm x 50mm Cross Section. The Legs are connected by MS Steel beams 50mm x 50mm x 2mm Thickness in cross section. The complete metal structure is Duly powder coated for 40-60 micron thickness. The Height of Top from floor Lever is 900mm. The Top of Lab Table is 18mm Thick Jet Black Granite Stone with Polished Edges on all sides. Neoprene Gasket is Placed on underside of Granite over Metal Under structure. Granite has necessary Holes for Electrical and Plumbing Inlets, Gas Pipe line etc. Both Ends of Lab Table are duly closed with 0.8mm thick CRCA Sheet Metal duly Powder coated to Give Clean appearance to the Lab Table. Providing and Connection of Services like Plumbing, Electrical, Gas etc are not in scope of Lab Table Supplier. Metal Storage – Is made of 0.8mm – 1mm thick CRCA Steel Sheet and is duly Powder coated. It has one number Pull out Unit and one Hinged Door Unit with 2 Doors. Dimension of Metal Storage is 700mm W x 400mm D x 635mm Ht. Wash Basin – Poly Propylene Sink Rectangular having dimension 600mm x 450mm x 300mm Ht . Sink is provided with outlet Nipple and this Assembly has PP Hose Pipe with Nut and PP Bottle Trap. - Tap – Each Wash Basin is supplanted with 2 No Water Tap for Both Side Lab Island or 1 No Water Tap for Single Side Lab Island. The Tap is Single Swan Water Tap duly Nickel Chrome Plated. Chemistry Lab Metal Rack with Wire Management – Metal rack made of CRCA 1mm thick Steel Sheet Duly Powder Coated is Provided above the Granite Top at specified Loaction as per Drawing. Rack is 650m Height from Table top Level and has 2 Levels. Lower Level has 150mm High Raceway for Fixing Electrical and Data Switches and Sockets ( Not in Scope of Lab Supplier ). The Shelf Verical is 30mm Thick CRCA Sheet and the Upper Shelf is 18mm thick Shelf. With Both Levels,Sufficient space for keeping Regents and Chemical Bottles is available.

HEMATOLOGY LAB , AMPHIBIAN LABORATORY , PRACTICAL LAB , HISTOLOGY LAB e) Lab Table ;-W6150xD1200xH1550 Providing and Supplying HNI Lab Table . The Understructure is made of 2mm Thick MS Steel Legs having 50mm x 50mm Cross Section. The Legs are connected by MS Steel beams 50mm x 50mm x 2mm Thickness in cross section. The complete metal structure is Duly powder coated for 40-60 micron thickness. The Height of Top from floor Lever is 900mm. The Top of Lab Table is 18mm Thick Jet Black Granite Stone with Polished Edges on all sides. Neoprene Gasket is Placed on underside of Granite over Metal Under structure. Granite has necessary Holes for Electrical and Plumbing Inlets, Gas Pipe line etc. Both Ends of Lab Table are duly closed with 0.8mm thick CRCA Sheet Metal duly Powder coated to Give Clean appearance to the Lab Table. Providing and Connection of Services like Plumbing, Electrical, Gas etc are not in scope of Lab Table Supplier. Metal Storage – Is made of 0.8mm – 1mm thick CRCA Steel Sheet and is duly Powder coated. It has one number Pull out Unit and one Hinged Door Unit with 2 Doors. Dimension of Metal Storage is 700mm W x 400mm D x 635mm Ht. Wash Basin – Poly Propylene Sink Rectangular having dimension 600mm x 450mm x 300mm Ht . Sink is provided with outlet Nipple and this Assembly has PP Hose Pipe with Nut and PP Bottle Trap. - Tap – Each Wash Basin is supplanted with 2 No Water Tap for Both Side Lab Island or 1 No Water Tap for Single Side Lab Island. The Tap is Single Swan Water Tap duly Nickel Chrome Plated. Chemistry Lab Metal Rack with Wire Management – Metal rack made of CRCA 1mm thick Steel Sheet Duly Powder Coated is Provided above the Granite Top at specified Loaction as per Drawing. Rack is 650m Height from Table top Level and has 2 Levels. Lower Level has 150mm High Raceway for Fixing Electrical and Data Switches and Sockets ( Not in Scope of Lab Supplier ). The Shelf Verical is 30mm Thick CRCA Sheet and the Upper Shelf is 18mm thick Shelf. With Both Levels,Sufficient space for keeping Regents and Chemical Bottles is available.

HEMATOLOGY LAB , AMPHIBIAN LABORATORY , PRACTICAL LAB , HISTOLOGY LAB f) Lab Table ;-W8450xD1200xH1550 - Providing and Supplying HNI Lab Table . The Understructure is made of 2mm Thick MS Steel Legs having 50mm x 50mm Cross Section. The Legs are connected by MS Steel beams 50mm x 50mm x 2mm Thickness in cross section. The complete metal structure is Duly powder coated for 40-60 micron thickness. The Height of Top from floor Lever is 900mm. The Top of Lab Table is 18mm Thick Jet Black Granite Stone with Polished Edges on all sides. Neoprene Gasket is Placed on underside of Granite over Metal Under structure. Granite has necessary Holes for Electrical and Plumbing Inlets, Gas Pipe line etc. Both Ends of Lab Table are duly closed with 0.8mm thick CRCA Sheet Metal duly Powder coated to Give Clean appearance to the Lab Table. Providing and Connection of Services like Plumbing, Electrical, Gas etc are not in scope of Lab Table Supplier. Metal Storage – Is made of 0.8mm – 1mm thick CRCA Steel Sheet and is duly Powder coated. It has one number Pull out Unit and one Hinged Door Unit with 2 Doors. Dimension of Metal Storage is 700mm W x 400mm D x 635mm Ht. Wash Basin – Poly Propylene Sink Rectangular having dimension 600mm x 450mm x 300mm Ht . Sink is provided with outlet Nipple and this Assembly has PP Hose Pipe with Nut and PP Bottle Trap. - Tap – Each Wash Basin is supplanted with 2 No Water Tap for Both Side Lab Island or 1 No Water Tap for Single Side Lab Island. The Tap is Single Swan Water Tap duly Nickel Chrome Plated. Chemistry Lab Metal Rack with Wire Management – Metal rack made of CRCA 1mm thick Steel Sheet Duly Powder Coated is Provided above the Granite Top at specified Loaction as per Drawing. Rack is 650m Height from Table top Level and has 2 Levels. Lower Level has 150mm High Raceway for Fixing Electrical and Data Switches and Sockets ( Not in Scope of Lab Supplier ). The Shelf Verical is 30mm Thick CRCA Sheet and the Upper Shelf is 18mm thick Shelf. With Both Levels,Sufficient space for keeping Regents and Chemical Bottles is available.

Lab Stool - Providing and Supplying Lab Stool with Seat Dia minimum 30 cm. The seat should be made up of 12mm thick hot pressed plywood upholstered with fabric / Leatherite and moulded polyurethane foam. Chair should be on a 4 legged Metal Pipe frame assembly with Height adhustability for seat and is duly powder caoted and provided with gliders as per manufacturer's specifications, drawings & direction of Engineer in charge. The above furniture should be as per specification and sample approved by client.

a) Storage :-W4650xD450xH1660- Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

b) Storage :-W5750xD450xH1660- Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

c) Storage :-W7750xD450xH1660- Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

d) Storage :-W8250xD450xH1660- Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

e) Storage :-W9100xD450xH1660 - Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

f) Storage :-W9600xD450xH1660 - Providing and placing HNI BP Ergo Trent Prelaminated Particle Board storage with openable doors , made up of 18mm thick prelaminated particle board with PVC edge banding and locking arrangement.Storage body is made of 18mm thick pre laminated partical Board conforming to IS : 12823 Interior Grade, The back of the unit is made from 18mm prelaminated board. All the exposed edges are with 2mm PVC egde Imported banding & sealed edges are with 0.8mm thick PVC Imported edge banding. The top, side and hinged shutters are sealed with 2mm thick PVC edge banding. The units are assembled by knock down fittings such as Minifix & Dowels. All the hardware and Hinges are from Hettich/Ebco. Storage has Brushed SS finish handles/ flush handles and lock . Prelam storage unit of standard 450mm depth.

Both Side Storage :-900mm L x 594mm D x 1890mm Ht. - Providing & Supplying Liabrary Rack of size 900mm L x 594mm D x 1890mm Ht. The top Panel is Made of CRCA Sheet and side panel is made up of 18mm thick pre laminated particle board of interior grade with laminate on both sides of approved make and shade. The working and non – working edges shall be provided with machine pressed 2mm thick PVC edging using special hot melt glue at high temperature. the back panel is made up of CRCA Metal Sheet Duly Powder Coated. Brackets holding the shelf are made up of 2mm thick CRCA. Metal shelfs are made up of 0.8mm thick CRCA powder coated finish as per the directions of Engineer in Charge. The above furniture should be as per specification and sample approved by client.

Demo Room , Demo 1&2 - a) Demo Room Table :-W1800xD600xH750mm - Providing & Fixing of HNI make league plus of 750mm Ht. The Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of powdered coated steel 50mmx 50mm Section. Cross Member are in CRCA steel and the Beam is made of MSof 1.5mm thickness in powder coated finish of 50 microns thickness . The above furniture should be as per specification and sample approved by client.

b) Demo Room Table :-W2550xD600xH750mm - Providing & Fixing of HNI make league plus of 750mm Ht. The Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of powdered coated steel 50mmx 50mm Section. Cross Member are in CRCA steel and the Beam is made of MSof 1.5mm thickness in powder coated finish of 50 microns thickness . The above furniture should be as per specification and sample approved by client.

Meeting Table :-W3000xD900xH750mm - Providing & Fixing of HNI "Ensemble " Confetrence table . the Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of Aluminum Extrusion of 1.6mm thickness with aesthically designed elliptical Cover sections . Legs are designed to facilitate wire management . Cross Member are in CRCA steel and the Beam is made of MS and has size 75x50 mm of 1.5mm thickness in powder coated finish of 50 microns thickness and is connected with legs to allow for traversing of wires horizontally. The beam raceway provided with slots for fixing data and electrical switches and sockets for each user under the table. The above furniture should be as per specification and sample approved by client.

Meeting Chair - Providing and supplying HNI Model Certo Medium Back Chair .This is a Medium back chair with Mesh Back with back tilt tension adjustable . The chair has Anchored Lumber Support . The Chair has Nylon base with 50 mm twin wheel castors .Chair comes with 1-D adjustable PP armrests . Seat size is 500 mm W x 520 mm D and the Chair Height 985 mm - 1080 mm . Overall size of the chair is 635mm W x 605 mm D x (985 mm- 1080mm) H . The PU foam used for chair seat is fire retardant . The chair has Pneumatic Gas Lift with Stroke=85 mm .

DISSECTION Area - DISSECTION Table :-W2100xD900xH750mm - Providing & Fixing of HNI make league plus of 750mm Ht. The Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of powdered coated steel 50mmx 50mm Section. Cross Member are in CRCA steel and the Beam is made of MSof 1.5mm thickness in powder coated finish of 50 microns thickness . The above furniture should be as per specification and sample approved by client.

DISSECTION Stool Providing and Supplying Lab Stool with Seat Dia minimum 30 cm. The seat should be made up of 12mm thick hot pressed plywood upholstered with fabric / Leatherite and moulded polyurethane foam. Chair should be on a 4 legged Metal Pipe frame assembly with Height adhustability for seat and is duly powder caoted and provided with gliders as per manufacturer's specifications, drawings & direction of Engineer in charge. The above furniture should be as per specification and sample approved by client.

ANTE RM. Locker :- 1800 ht x 375 W x 450 D mm Providing and Supplying 4 Door Steel Personal Locker unit. The Complete unit is made of 0.6mm thick CRCA Sheet duly powder coated for 40-50 micron thickness. The Unit size is 1800mm Ht x 375mm W x 450mm D. The Door has individual locks for both doors. The Locker has Perforations in door. The door has Recessed Handle made of Moulded Engineering Plastic.

a) Main Table :-W2700xD900xH750mm Providing and Placing HNI make Cabin Table "STELLAR" . Main Table and Side Table made of 36 mm thick Pre Laminated Particle Board with matching 2 mm thick edge Banding. Modesty panels are in 18mm thk Postlaminated finish. Table supports are combination of Metal poles and Gable ends. Access Flap with Cable tray and switch mounting plate is provided on side table for wire management. Back storage unit Combination of Hinged Door unit and has Tower Assembly with Glass Shelves on top of Hinged Door Unit. Back Unit and Tower unit are made of Prelaminated particle Board 18mm thick with Matching PVC lipping. SS handles 220mm L are provided in storages. 3 drawer pedestal unit has castors and pedestal unit is made up of 18mm thk. Prelaminated Particle Board Caracass having central locking system . 2 Drawers are with roller slide mechanism and Filing Unit is with Ball bearing slides. ACADEMIC- 3

b) Side Return :-W1350xD450xH750mm Providing and Placing HNI make Cabin Table "STELLAR" . Main Table and Side Table made of 36 mm thick Pre Laminated Particle Board with matching 2 mm thick edge Banding. Modesty panels are in 18mm thk Postlaminated finish. Table supports are combination of Metal poles and Gable ends. Access Flap with Cable tray and switch mounting plate is provided on side table for wire management. Back storage unit Combination of Hinged Door unit and has Tower Assembly with Glass Shelves on top of Hinged Door Unit. Back Unit and Tower unit are made of Prelaminated particle Board 18mm thick with Matching PVC lipping. SS handles 220mm L are provided in storages. 3 drawer pedestal unit has castors and pedestal unit is made up of 18mm thk. Prelaminated Particle Board Caracass having central locking system . 2 Drawers are with roller slide mechanism and Filing Unit is with Ball bearing slides.

c) Side Return :-W1500xD450xH750mm Providing and Placing HNI make Cabin Table "STELLAR" . Main Table and Side Table made of 36 mm thick Pre Laminated Particle Board with matching 2 mm thick edge Banding. Modesty panels are in 18mm thk Postlaminated finish. Table supports are combination of Metal poles and Gable ends. Access Flap with Cable tray and switch mounting plate is provided on side table for wire management. Back storage unit Combination of Hinged Door unit and has Tower Assembly with Glass Shelves on top of Hinged Door Unit. Back Unit and Tower unit are made of Prelaminated particle Board 18mm thick with Matching PVC lipping. SS handles 220mm L are provided in storages. 3 drawer pedestal unit has castors and pedestal unit is made up of 18mm thk. Prelaminated Particle Board Caracass having central locking system . 2 Drawers are with roller slide mechanism and Filing Unit is with Ball bearing slides.

d) Back Storage :-W2800xD450xH750mm Providing and Placing HNI make Cabin Table "STELLAR" . Main Table and Side Table made of 36 mm thick Pre Laminated Particle Board with matching 2 mm thick edge Banding. Modesty panels are in 18mm thk Postlaminated finish. Table supports are combination of Metal poles and Gable ends. Access Flap with Cable tray and switch mounting plate is provided on side table for wire management. Back storage unit Combination of Hinged Door unit and has Tower Assembly with Glass Shelves on top of Hinged Door Unit. Back Unit and Tower unit are made of Prelaminated particle Board 18mm thick with Matching PVC lipping. SS handles 220mm L are provided in storages. 3 drawer pedestal unit has castors and pedestal unit is made up of 18mm thk. Prelaminated Particle Board Caracass having central locking system . 2 Drawers are with roller slide mechanism and Filing Unit is with Ball bearing slides.

e) Back Storage :-W3900xD450xH750mm Providing and Placing HNI make Cabin Table "STELLAR" . Main Table and Side Table made of 36 mm thick Pre Laminated Particle Board with matching 2 mm thick edge Banding. Modesty panels are in 18mm thk Postlaminated finish. Table supports are combination of Metal poles and Gable ends. Access Flap with Cable tray and switch mounting plate is provided on side table for wire management. Back storage unit Combination of Hinged Door unit and has Tower Assembly with Glass Shelves on top of Hinged Door Unit. Back Unit and Tower unit are made of Prelaminated particle Board 18mm thick with Matching PVC lipping. SS handles 220mm L are provided in storages. 3 drawer pedestal unit has castors and pedestal unit is made up of 18mm thk. Prelaminated Particle Board Caracass having central locking system . 2 Drawers are with roller slide mechanism and Filing Unit is with Ball bearing slides.

f) Back Storage :-W5150xD450xH750mmProviding and Placing HNI make Cabin Table "STELLAR" . Main Table and Side Table made of 36 mm thick Pre Laminated Particle Board with matching 2 mm thick edge Banding. Modesty panels are in 18mm thk Postlaminated finish. Table supports are combination of Metal poles and Gable ends. Access Flap with Cable tray and switch mounting plate is provided on side table for wire management. Back storage unit Combination of Hinged Door unit and has Tower Assembly with Glass Shelves on top of Hinged Door Unit. Back Unit and Tower unit are made of Prelaminated particle Board 18mm thick with Matching PVC lipping. SS handles 220mm L are provided in storages. 3 drawer pedestal unit has castors and pedestal unit is made up of 18mm thk. Prelaminated Particle Board Caracass having central locking system . 2 Drawers are with roller slide mechanism and Filing Unit is with Ball bearing slides.

g) Back Storage :-W5350xD450xH750mmProviding and Placing HNI make Cabin Table "STELLAR" . Main Table and Side Table made of 36 mm thick Pre Laminated Particle Board with matching 2 mm thick edge Banding. Modesty panels are in 18mm thk Postlaminated finish. Table supports are combination of Metal poles and Gable ends. Access Flap with Cable tray and switch mounting plate is provided on side table for wire management. Back storage unit Combination of Hinged Door unit and has Tower Assembly with Glass Shelves on top of Hinged Door Unit. Back Unit and Tower unit are made of Prelaminated particle Board 18mm thick with Matching PVC lipping. SS handles 220mm L are provided in storages. 3 drawer pedestal unit has castors and pedestal unit is made up of 18mm thk. Prelaminated Particle Board Caracass having central locking system . 2 Drawers are with roller slide mechanism and Filing Unit is with Ball bearing slides.

Main ChairVerta HB with Headrest High Back W/ Headrest Fabric Upholstered & Leatherite Upholstered Weight activated synchronize w/ Seat Depth Adj 4D Adj. Black PU Armrests 4D With Lumbar Support Adjustment Black Back Frame Black Y Support Polished Aluminium Base 380 Imitation Leather 380 WARRANTY: 10 Years from the date of invoiceDIRECTOR , PRESIDENT , REGISTRAR , DEAN

Round Table :-W1200mm DiaRound table 1200mm Dia, of 25mm prelaminated particle board with CRCA Powder coated base Model Alfa.

Round Table ChairProviding and supplying HNI Model Ativo Medium Back Chair with Curvature Backrest.The curvature Corresponds to natural curves of spine and supports lumber assuring supreme comfort and no upper - body strains. This is a Medium back chair with Mesh Back with back tilt tension adjustable . The chair has Adjustable Lumber Support . The Chair has Nylon base with 60 mm twin wheel castors .Chair comes with 1-D adjustable armrests . Seat size is 500 mm W x 515 mm D and the Chair Height 975 mm - 1070 mm . Overall size of the chair is 640mm W x 665mm D x (975 mm- 1070mm) H . The PU foam used for chair seat is fire retardant . The chair has Pneumatic Gas Lift with Stroke=85 mm . . Chair carries a warranty of 5 years.

a) 3 Seater SofaProviding & Fixing of sofa . The inside frame is made of seasoned wood and has antitermite treatment. The seat and back are made of foam and is finished in leatherite upholestry. The Frame base has Webbing for Supporting the Cushions. The Complete Sofa Body has Polyurethane Foam in desired shape. The Sofa is supported on Metal Chrome Plated Legs. Leatherite colour and type as per directions of Engineer in Charge.

b) 2 Seater SofaProviding & Fixing of sofa . The inside frame is made of seasoned wood and has antitermite treatment. The seat and back are made of foam and is finished in leatherite upholestry. The Frame base has Webbing for Supporting the Cushions. The Complete Sofa Body has Polyurethane Foam in desired shape. The Sofa is supported on Metal Chrome Plated Legs. Leatherite colour and type as per directions of Engineer in Charge.

Providing and placing HNI "Winner" , Table completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. The Table has Built in 1 Door Pull Out Unit with lock and handle.Table :-W1200xD600xH750mmLECTURE Hall

PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM, CO-ORDINATORa) Main Table :-W1500xD750xH750mmProviding and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

b) Main Table :-W1800xD750xH750mmPRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM, CO-ORDINATORProviding and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

c) Side Return :-W900xD450xH750mm-PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM, CO-ORDINATORProviding and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

d) Side Return :-W1050xD450xH750mm-PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM, CO-ORDINATORProviding and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

e) Back Storage :-W2100xD450xH750mmPRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM, CO-ORDINATORProviding and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

f) Back Storage :-W2400xD450xH750mmPRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM, CO-ORDINATORProviding and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

g) Back Storage :-W2550xD450xH750mmPRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM, CO-ORDINATORProviding and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

h) Back Storage :-W2700xD450xH750mmPRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM, CO-ORDINATORProviding and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

i) Back Storage :-W3150xD450xH750mm PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM, CO-ORDINATORProviding and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

j) Back Storage :-W3400xD450xH750mm PRO. , DY. CHIEF SECURITY OFF. , SR. ANALYST (IT) , SR. HINDI OFF. , LAW OFF. , ASS.ADMIN OFF. , ADMIN OFF. , SR.ADMIN OFF , SR. OFF , TUTOR-1&2 , HOD ROOM , ASSOCIATE PROFF. , ASST PROFF , IN-CHARGE ROOM, CO-ORDINATORProviding and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

a) Main Table :-W1500xD600xH750mmPS Room , REC.Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

b) Main Table :-W1800xD750xH750mmPS Room , REC.Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

c) Side Table :-W900xD450xH750mmPS Room , REC.Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

d) Back Storage :-W2100xD450xH750mmPS Room , REC.Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

e) Back Storage :-W3600xD450xH750mmPS Room , REC.Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

f) Back Storage :-W4050xD450xH750mmPS Room , REC.Providing and placing HNI Make "Trent" , Main Table , completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Side table with Postformed Curvica Top on User side and rest completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top is supported on 18mm thk. Gable ends and 18mm thk. Modesty panel. Exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. It has CPU storage space. . Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit. Back Storage Made of 18mm PLPB with Hinged Door Unit and Lockable Doors.

TECHNICIAN , COMPUTER OPERATORProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. a) FACULTY EXAMINATION. Workstation :-W5550xD600xH750mm

TECHNICIAN , COMPUTER OPERATORProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. b) FACULTY EXAMINATION. Workstation :-W5950xD600xH750mm

TECHNICIAN , COMPUTER OPERATORProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. c) FACULTY EXAMINATION. Workstation :-W6250xD600xH750mm

TECHNICIAN , COMPUTER OPERATORProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. d) Workstation :-W3650xD600xH1200mm

TECHNICIAN , COMPUTER OPERATORProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. e) Workstation :-W4950xD600xH1200mm

TECHNICIAN , COMPUTER OPERATORProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. f) OFFICE CLERICAL Workstation :-W5250xD600xH750mm

TECHNICIAN , COMPUTER OPERATORProviding and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. g) OFFICE CLERICAL Workstation :-W5750xD600xH750mm

Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. Straight Workstation :-W5550xD600xH750mm

Conference RoomProviding and placing Meeting Room table in "U" Shape . Table Tops – Available in standard modules 1500mm L x 750mm D / 1350mm L x 750mm D / 1200mm L x 750mm D / 1050mm L x 750mm D / 900mm L x 750mm D /750mm L x 750mm D , made of 25mm thick Prelaminated Partlice Board. Understructure – Legs made of 18mm thick Prelaminated Particle Board panels interconnected with 18mm thick pre-laminated modesty panels, with height adjustable levelers to take care of uneven floors. Wire Management – Concealed wire management to take care of basic wiring requirements both horizontally & vertically. Cable Tray is mounted on the inner side of modesty panel for horizontal wire carrying. Vertical wire management is through flexible vertical wire manager at one place . Slots for Mounting Data and Electric Switches and Sockets are provided on Cover Section of Cable Tray. Standard table top height – 750mm. Designed for Flexibility through modular Construction, Provision for easy wire management, Upgradeable / reconfigurable for future needs. Corners are Provided in 25mm thickness . Corners are supported on 63.5mm Painted Metal Pole with Leveller for Height Adjustment. a) Closed Shape Table :-W7750x1800xD750xH750mm

Conference RoomProviding and placing Meeting Room table in "U" Shape . Table Tops – Available in standard modules 1500mm L x 750mm D / 1350mm L x 750mm D / 1200mm L x 750mm D / 1050mm L x 750mm D / 900mm L x 750mm D /750mm L x 750mm D , made of 25mm thick Prelaminated Partlice Board. Understructure – Legs made of 18mm thick Prelaminated Particle Board panels interconnected with 18mm thick pre-laminated modesty panels, with height adjustable levelers to take care of uneven floors. Wire Management – Concealed wire management to take care of basic wiring requirements both horizontally & vertically. Cable Tray is mounted on the inner side of modesty panel for horizontal wire carrying. Vertical wire management is through flexible vertical wire manager at one place . Slots for Mounting Data and Electric Switches and Sockets are provided on Cover Section of Cable Tray. Standard table top height – 750mm. Designed for Flexibility through modular Construction, Provision for easy wire management, Upgradeable / reconfigurable for future needs. Corners are Provided in 25mm thickness . Corners are supported on 63.5mm Painted Metal Pole with Leveller for Height Adjustment. b) U Shape Table :-W9950x6650xD750xH750mm

Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. a) Workstation :-W1500xD60xH750mm

Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. b) Workstation :-W2100xD60xH750mm

Providing and placing HNI make "Connect 50" Linear Workstation . Frame is 50 mm thick and made of Aluminium Extrusions of 1.2 mm to 1.5mm thickness. The System is complete hollow system with space for wire reticulation . All the frames will be duly powder coated . All the frames are fastened together by means of M6 NUTS & BOLTS . All the frames are fitted with M10 leveling bolts.board.Raceway :-The raceway cover are sliding type and are integrally fitting inside frame and are made out of 0.8mm - 1mm thick CRCA steel & powder coated. The electrical raceway can be provided below worktop or above worktop.The partition has two integrated raceway provided one at skirting level and another at the work surface level thus ensuring separation of power and networking cables. The free space available within raceway accommodates power, data and communication cables. The cable can be taken into the Frame from the floor from the bottom. Tiles: Fabric Tile: Constructed out of 5mm thick Medium Density Fiber Board (MDF) and covered with Fabric of choice. Laminate Tile: Made out of 5mm - 8mm thick Pre-laminated Medium Density Fiber Board (MDF) Bottom Row of Steel Tile: Constructed out of 0.8mm CRCA sheet and finished in epoxy powder coating. Can be given with plain / perforations / embossed finishes.Magnetic tile: Constructed out of 0.8mm Galvanized sheet and covered with fabric of choice. Whiteboard marker tiles: Made out of 4mm MDF with 1mm glossy highly wear resistant face laminate . Total thickness is 5mm. Table tops and Gable ends are of 25mm thk Pre-laminated particleboards conforming to IS : 12823 Interior Grade. All Worktops to have Metal Insets for fixing screws. Specially designed powder coated M.S. brackets having 2mm thickness fixed to the partition frame support the tabletops. Gable ends are of 25mm thk. both side laminate (BSL) with 2mm PVC edge banding on front side. Gable Ends are fixed with 3mm thick MS brackets to Frame and with 3mm thick Brackets to Worktops. Sealed edge in table top and gable ends are with2mm thick PVC edge banding on Working side and 0.8mm thick edge banding on non working side. c) Workstation :-W2700xD60xH750mm

Providing & Fixing of HNI make league plus cafe table of 750mm Ht. The Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of powdered coated steel 50mmx 50mm Section. Cross Member are in CRCA steel and the Beam is made of MSof 1.5mm thickness in powder coated finish of 50 microns thickness . The above furniture should be as per specification and sample approved by client.a) Café Table :-W1200xD750xH750mm

Providing & Fixing of HNI make league plus cafe table of 750mm Ht. The Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of powdered coated steel 50mmx 50mm Section. Cross Member are in CRCA steel and the Beam is made of MSof 1.5mm thickness in powder coated finish of 50 microns thickness . The above furniture should be as per specification and sample approved by client.b) Café Table :-W1800xD750xH750mm

Providing and Supplying Double Bed having Dimensions: Length (2000mm), Width (1800mm), Height (400mm). The Bed is Openable flap storage type . Bed has Head board and Footboard. Head side Board has 800mm Height and is Aesthetically designed for Elegent Looks.Primary Material: Engineered Panl - PLPB.Color: Natural Wenge,Double Bed - Warden Room

Providing and placing HNI "Winner" , Table 900 x 600mm, completely made up of Prelam particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility. The Table has Built in 1 Door Pull Out Unit with lock and handle.Study table

Providing and fixing BP Ergo Model Gail Medium Back Mesh Chair with Lumber Support, Seat Size 500mm W x 500mm D, Back Size 480m W x 520mm Ht, PP Arms, Nylon Base, Push Back Mechanism, 50m Nylon Castors , Gas Lift, Net Back, Seat Fabric Upholestry. Seat Height Minimum 480mm from Ground and Maximum 570mm. The Chair Warranty : 3 Years.Study Chair

Single BedProviding & Placing Bed of size 2000 mm x 900mm The top of the bed is 18 mm thick ISI marked Pre-laminated Board, grade conforming to IS:12406 fixed on 19mm x19mm cross stiffeners frame. The 3 sides of the bed to be in 50x25mm MS Tubes and cladded with 18 mm thick Pre-laminated board , conforming to IS:12406 . The head & Foot rest to be as per drawing in 18mm Pre-laminated board conforming to IS:12406 to achieve shape and design. The bed has four legs made out of 50x25x1.6mm thk MS tubes. Decorative Teak Wood Lipping is provided on all the edges of bed. All Metal Parts is Duly Powder Coated with 45 microns.(Without Matress)

Study ChairProviding and fixing BP Ergo Model Gail Medium Back Mesh Chair with Lumber Support, Seat Size 500mm W x 500mm D, Back Size 480m W x 520mm Ht, PP Arms, Nylon Base, Push Back Mechanism, 50m Nylon Castors , Gas Lift, Net Back, Seat Fabric Upholestry. Seat Height Minimum 480mm from Ground and Maximum 570mm. The Chair Warranty : 3 Years.MORTURY

Straight Tables- Console Room - 4000mm l x 750mm W x 750mm Ht Providing and placing HNI "Trent" , Table in standard modules of size 900mm L , 1050mm L , 1200mm L ,1350mmL , 1500mm L x 750mm D , 600mm D, completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Each Module shall have a Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit.

Straight Tables- Examination Room -1800mm l x 600mm W x 750mm Ht Providing and placing HNI "Trent" , Table in standard modules of size 900mm L , 1050mm L , 1200mm L ,1350mmL , 1500mm L x 750mm D , 600mm D, completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Each Module shall have a Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit.

Straight Tables- Office - 3000mm l x 600mm W x 750mm Ht Providing and placing HNI "Trent" , Table in standard modules of size 900mm L , 1050mm L , 1200mm L ,1350mmL , 1500mm L x 750mm D , 600mm D, completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Each Module shall have a Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit.

Office - 2750mm l x 600mm W x 750mm Ht Providing and placing HNI "Trent" , Table in standard modules of size 900mm L , 1050mm L , 1200mm L ,1350mmL , 1500mm L x 750mm D , 600mm D, completely made up of Postform Curvica particle board conforming to IS : 12823 Interior Grade with PVC edge banding. Top are with 25mm thk boards with post formed Edge on User and Visitor Side . Table top is supported on 18mm thick Gable ends and 18mm thk Modesty panels. exposed edges are in 2mm thk PVC edge banding & sealed edges are in 0.8mm thk PVC edge banding. Separate provision for mounting switches on the wall adjoining the tables shall be made by customer as the tables do not come with switch mounting facility.Each Module shall have a Pedestal unit of size 400mm L x 450mm D x 680mm made up of 18mm thk. Prelam particle board conforming to IS : 12823 Interior Grade with 3 Drawer ( 2 Drawer + 1 Filing ) with roller slide mechanism for 2 Drawers and Ball bearing slide for 1 Filng Unit.

Study Chair- Providing and fixing BP Ergo Model Gail Medium Back Mesh Chair with Lumber Support, Seat Size 500mm W x 500mm D, Back Size 480m W x 520mm Ht, PP Arms, Nylon Base, Push Back Mechanism, 50m Nylon Castors , Gas Lift, Net Back, Seat Fabric Upholestry. Seat Height Minimum 480mm from Ground and Maximum 570mm. The Chair Warranty : 3 Years.

Cupboard- Providing & Supplying Cabinet . It shall have dimensions 900mm (W) x 1660 mm (H) x 450 mm (D) and shall be made of prime Quality CRCA 0.8mm thk for all the body panels and shelves having top & bottom stiffeners in 0.8mm CRCA steel.. Shelves are adjustable in variable heights and shall have Uniformly Distributed Load capacity of 50 Kg per shelf . The vertical sides of storages from inside have contineous slots for mounting variable height shelves. Complete carcass is finished with Epoxy polyester powder coating finish 50 +/-10 microns 2)Facia : The cabinet shutters are made of Metal 3)Handles : Handle Shall be aesthetically designed D handles in SS finish. 4) Locking Mechanism: Locking Mechanism shall be Cam lock in Metal Door. 5)Levellor: It also have adjustable Leveler with plastic base with height adjustment up to 15mm. The above furniture should be as per specification and sample approved by client.

Dinning Table - 1800mm l x 900mm W x 750mm Ht- Providing & Fixing of Cafe table . The Worktop shall be made of 25mm Prelamparticle Board of Grade II , Type-II as per IS:12823 and backing laminate of 0.6mm All the exposed edges are finished with 2mm thick PVC lipping machine pressed. Legs are made of powdered coated steel 50mmx 50mm Section. Cross Member are in CRCA steel and the Beam is made of MSof 1.5mm thickness in powder coated finish of 50 microns thickness . The above furniture should be as per specification and sample approved by client.

TABLE MAIN 1200W-750D-900H

TABLE ADDON 600W-750D-900H

TABLE ADDON 1200W-750D-900H

UNDERBENCH CABINET 600W-450D-674H 2S

REAGENT SHELF ISLAND MAIN 600W

REAGENT SHELF ISLAND MAIN 1200W

LEG SPACE PANEL SET 600W-900H

ISLAND SIDE PANEL SET 1500W-900H

Pp Drop-In Sink Model S 06 560 Mm (W) X 355 Mm (D)

Ss Pegboard 550X420X55, 25 pegs

Single Tap Deck Mounted, 8" Swing Gooseneck, Without Positioning Pins Model No.100/33

Jet Black Granite (Sq.Mt.) 20 (±2) Mm Thk

Silicon Sealant - Black

Neoprene Strip (Running Meter) (30Mm Wide & 6 Mm Thick)

Masking Tape

Sr-998 Glue For Neoprene Mat. (Litres)

Flexible/F Serated Connector Model : Hp 01 Make: Premier

Anti-Siphon Bottle Trap Model : S 04 Make: Premier

16A, 1 Way Switch - Model No: M0130

6/16A, 6 Pin Shutter Socket - Model No: M1332

3 Module Plate - Model No: Cs933M

BKT- For Island Table

WF-2S-1D-600W-725H(450 height )

WF-1S-1D-RH-450W-725H(450 height )

TABLE MAIN 1050W-750D-900H

TABLE ADDON 1050W-750D-900H

SMT-1200W-750D-750H

SAT-450W-750D-750H

SAT-1200W-750D-750H

UNDERBENCH CABINET 600W-450D-674H 2S 1D

UNDERBENCH CABINET 600W-450D-506H 2S 1D

UNDERBENCH CABINET 450W-450D-674H 1S 1D RH

UNDERBENCH CABINET 450W-450D-506H 1S 1D LH

REAGENT SHELF ISLAND MAIN 1050W( with tube light)

REAGENT SHELF ISLAND ADDON 1500W(with tube light)

REAGENT SHELF ISLAND ADDON 1050W (with tube light)

Modesty Panel 450W X 725H (450 height)

Modesty Panel 1200W X 725H (450 height)

Filler Panel For Wall Side Furniture Without Upright With Modesty Panel 620 Wd X 725H (450 height)

REAR SIDE PANEL SET 750D-750H

Back Support Bracket Without Upright For 620 Working Depth(450 Height)

2-Way Lpg Valve Broen

TABLE ADDON 600W-750D-900H

TABLE ADDON 1050W-750D-900H

UNDERBENCH CABINET 600W-450D-674H 2S

UNDERBENCH CABINET 450W-450D-674H 1S 1D RH

WALL CABINET 600W-320D-674H 2S

REAR SIDE PANEL SET 750D-900H

CORNER TABLE PIPE FRAME 750D-900H

CORNER TABLE DOOR FRAME 900H

CORNER TABLE CABINET FILLER PANEL FOR CABINET 900H

SIDE PANEL FOR SINK UNIT

TABLE ADDON 450W-750D-900H

TABLE ADDON 1200W-750D-900H

UNDERBENCH CABINET 600W-450D-674H 2S

UNDERBENCH CABINET 450W-450D-674H 1S 1D RH

WALL CABINET 600W-320D-674H 2S

REAR SIDE PANEL SET 750D-900H

CORNER TABLE PIPE FRAME 750D-900H

CORNER TABLE DOOR FRAME 900H

TABLE ADDON 600W-750D-900H

WALL CABINET 600W-320D-674H 2S

REAGENT SHELF ISLAND MAIN 600W

REAGENT SHELF ISLAND MAIN 1200W

KMV PROJECTS LIMITED