Webel Bhavan FF ELECAC IDM 20 21 41

Amount

TAP OFF DISTRIBUTION BOARD

Manufacturing, supplying, installation, testing and commissioning of wall mounting cubicle type Tap off Distribution Board, top & bottom entry made of 2.03mm thick CRCA MS sheet suitable for 500/415V, AC, 50Hz, 3 Phase & Neutral system complete with PVC insulated Aluminium Bars and interconnection, painting, earthing attachment, gland plates etc with following equipments.

Incoming-

i) 1 no. - 500/415V, 32 A, TP&N MCB (36KA)

ii) 1 set (3nos) - RYB Phase LED Indicating Lamp with 3nos SP MCB.

iii) 32 A, 4P, PVC insulated Aluminium Bus Bars complete with FRP supports.

Outgoing-

i) 1nos - 500/415V, 32 A, 4P MCB (C-Curve, 10KA).

Flexible cable

Supplying and drawing of PVC insulated 4 runs 6 sq.mm, single core copper conductor cables through PVC flexible conduit including necessary termination at both end with copper flat, socket, PVC coupler and consumable materials etc. Necessary drilled hole shall be done on pre-fixed existing Rising Mains cover & Bus Bars of the premises including tools & tackles, labours etc as requird.

DISTRIBUTION BOARDS

Supplying and fixing double door Vertical TPN MCB Distribution board for MCB incomer with IP-42/43 protection, on angle iron frame on wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attchment

Up to 32 A

6 Way Enclosure

Supplying and fixing double door Horizontal TPN MCB Distribution board with IP-42/43 protection, concealed in wall after cutting the wall & mending good the damages to original finish incl. Inter connection with suitable size of copper wire and neutral link & provision for earthing attchment

4 Way Enclosure

Supplying and fixing 240/415 V MCB of breaking capacity 10 KA & C characteristics on din rail of existing DBs and necessary connection

Surge Protective Device

Supplying and fixing Class-2 (T2) 415V, FP Surge Protective Device (SPD) of Imax 40kA/pole mounted on din rail of existing DBs and necessary connection

MV Cable & Termination

Supplying, laying, testing and commissioing of 1.1KV grade, A2XFY XLPE Armoured Aluminium cable of following size with all necessary accessories required for installation on the wall above false ceiling and concealed/surface on wall below the false ceiling, Rate shall include with 2 NOS. 8 SWG GI earth continuity Wire for running earth and all civil work like cutting dressing mending good damages as required. The cable shall be laid underground/on wall/in trench-the rate shall be included necessary clamping arrangement as required.

4 core 10 sqmm

Cable End Termination

Supplying and fixing Double Compression type Gland complete with brass gland, brass ring & rubber ring for dust & moisture-proof entry of XLPE armoured cable as below:

4 core 10 sqmm

Finishing the end of following XLPE armoured cables by crimping method incl. supplying and fixing solderless socket (Dowels make),tapes,anticorrosive paste & jointing materials:

4 core 10 sqmm

SUB MAINS/CIRCUIT MAINS

Wiring With PVC Insulated & Unsheathed Single Core Stranded Copper Wire ‘'FRLS' – in PVC Rigid/Flexible Conduit 'FRLS' (ISI Marked) on wall/ceiling/Furniture as per site requirement (concealed / surface)

Supplying & drawing of wiring in 1.1 KV single core stranded 'FRLS' PVC insulated & unsheathed copper wire in 20mm size PVC rigid/flexible conduit (as per direction by EIC) 'FRLS' including necessary Fittings and necesaary connections as required

2 x 36/0.3 (2.5 sqmm) + 1 x 22/0.3 (1.5 sqmm) ECC.

2 x 56/0.3 (4 sqmm) + 1 x 36/0.3 (2.5 sqmm) ECC.

Wiring With PVC Insulated & Unsheathed Single Core Stranded Copper Wire ‘'FRLS' – in PVC Casing-Capping on wall/ceiling/Furniture as per site requirement

Supplying & drawing of Wiring in 1.1 KV grade single core stranded 'FRLS' PVC insulated & unsheathed copper wire of following sizes in 25mm PVC casing-capping (as per direction by EIC) including necessary PVC clips, fittings, necessary connections as required

2 x 36/0.3 (2.5 sqmm) + 1 x 22/0.3 (1.5 sqmm) ECC.

POINT WIRING

Supplying and carrying wiring for light, fan and dependent socket points by using 16 SWG MS/PVC conduits with threaded joints of required dia as per IS 732, MS conduit accessories, MS/PVC flexible conduit with couplers for drops with accessories, 2 x 1.5 + 1 x 1.5 sq mm, 1100V grade FRLS PVC insulated copper wires approved 6A modular type switches and sockets with plates and all accessories for fixing in modular furniture, GI/PVC boxes and other point wiring accessories and carrying out surface/concealed conduit system of wiring as per requirement with all wiring materials. Conduits shall run on surface of the ceiling above false ceiling and concealed in wall by cutting chase in wall and mending good of all the damages.

All points shall be earthed with 1.5 sq mm FRLS flexible copper wire. Wires shall be terminated at light fixtures with ferrules, 16A, 4 way connector, wire ends shall not be kept loose/bare.

The rate shall also include all accessories of MS/PVC conduits, etc, necessary civil works for embedding conduits and boxes below false ceiling, wherever applicable.

1 light point controlled by 1 no. 6A switch with indicator

2 light points controlled by 1 no. 6A switch with indicator.

3 light points controlled by 1 no. 6A switch with indicator

SWITCHES & SOCKETS

SIT & C of the following components like approved plate type modular switches, socket etc, duly wired. All the switch sockets are with front plate and without boxes since the same is covered under different item.

1 No. - 6/16A, 6 pin in universal socket controlled by 16A, SP switch , RP in workstations and in cabins, with MS/PVC Box.

Same as above but without MS/PVC Box

3 Nos - 6A, 3 pin socket controlled by common 16A, SP switch , workstations without MS/PVC Box

Same as above but with MS/PVC Box

LIGHT AND FAN FIXTURE WORK

INDOOR TYPE LUMINAIRE

Supply, installation, testing and commissioning of light fixture complete with all accessories, as required. Erection rate shall include necessary GI chain and supporting suspending hardware for fixing the light fittings.

Recessed mounted circular down lighter (Philips Cat No. DN195B LED 20S - 6500 PSU WH S1) or approved equivalent.

Dismantling

Dismantling of existing light fittings,switch boards, conduit, if any.

AC Sockets

Supply and flush fixing of modular type heavy duty plug socket unit comprising of 16/25A socket and plug top (with indicator) and solid state type starter units of electronic type with highflow voltage protections, O/L protect etc and suitable for 1.5/1.0 TR AC Units modular type and completely wired including cutting chases and mending good damages, painting, earthing, necessary connections complete, as per required for AC Units.

MCB Enclosure for AC

SITC of 6-32 Amps DP MCB (D-Curve) with metal enclosure (outdoor type-IP65)near AC ODU (concealed/surface)

Empty Conduits

Supply and fixing of FRLS PVC (ISI marked) conduit (rigid/flexible) of various dia, exposed or concealed with all accessories like tees, bends, glands etc. JBs (PVC) as required and fish wire etc for wiring purpose complete and mending good damages to building works.

20 mm dia (2 mm thick)

Supplying and fixing PVC casing-capping on wall or ceiling, including elobw, necessary PVC fittings etc. amd mending good damages to building works

20x10 mm Size

HI WALL SPLIT AC

Supply, Installation, Testing & commissioning of Hi-wall Split 1st charge R-32/R-410A gas BEE 3 STAR RATED non inverter type air-cooled split Air-conditioner with cordless remote, hermetic/semi hermetic rotary type compressor having with copper coil of IDU & ODU, 3 Mtrs. Copper pipe with Armaflex insulation and 25 mm hard drawn UPVC piping with Armaflex insulation for sweat water drain complete as per direction of Engineer-in-charge. Extra copper pipe line (Suction & Liquid) beyond 3 mtr. will be paid extra as per measurement.

1.5 tr - 3 star rated

1.0 tr - 3 star rated

REFRIGERANT PIPING

Supply and installation testing & commissioning of required size soft/hard drawn refrigerant piping for the 1.5/ 1.0 TR. High-wall split type A.C. Units including Nitryle Rubber Insullation.

DRAIN PIPING

Supplying and laying of condensate drain line with PVC pipe complete with all accessories with 6mm Nitryle Rubber Insulation .

CABLE

Supply & laying, dressing, clamping, testing and commissioning of 1.1 KV grade, stranded copper conductor, PVC insulated, extruded PVC inner sheathed, Galvanized wire/strip armoured and PVC outer sheathed LT control cable confirming to IS 1554 (Part-1) and of following size.

ODU STRUCTURE

Supplying and installation of powder coated ODU Angle for installation of Out door unit with all accessories including ribbed neoprene VI Pads , for Hi-wall splits & Cassettes AC machines

1.0 TR & 1.5 TR(Hi-wall Split AC)

Abdul Electricals and Infrastructures Pvt Ltd

The Suburban Electric Co.

Mukherjee Commercial Enterprise