Construction of Public Gathering Center at Samar Yokma Kharboo

Earth work in bulk excavation by mechanical means (hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 m2 on plan) including disposal of excavated earth lead upto 50 meters and lift upto 1.5 m, as directed by Engineer-in-Charge.ALL KINDS OF SOIL 80%

ORDINARY ROCK 20%

Excavation work in excavation by mechanical means (Hydraulic excavator)/ in foundation trenches or drains (not exceeding 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in- charge.ALL KINDS OF SOIL 60%

ORDINARY ROCK 40%

Stone soling(Dumping of stone including cost of stone (in horizaontal on level)

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:4:8 (1 cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)

Providing and laying position cement concrete of specified grade excluding the cost of centering and shuttering. All work upto plinth level 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) (crushed) including Carraige of materials, loading and unloading.

Random rubble masonry DRY with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand), stone availaible at site

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand), stone availaible at site

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) including Carraige of materials, loading and unloading.

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) including Carraige of materials, loading and unloading.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including shuttering propping etc and removal of form for Foundation,footing bases of columns etc for mass concrete.

Centering and shuttering including shuttering propping etc and removal of form for Columns, pillars, piers, abutments, posts and struts.

Centering and shuttering including shuttering propping etc and removal of form for Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Suspended floor, roofs

Edge of slab

Providing & fixing upto floor five level precast cement concrete solid blocks including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete

Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with hold fast lugs or with dash fasteners of required dia and length (hold fast lugs or dash fastener shall be paid for seperately) 2nd class kail wood

Providing and fixing panelled or panelled and glazed shutters for doors,windows and clerestory windows fixing with butt hinges of required size with necessary screws, including panelling which will be paid for separately, all complete as per direction of Engineer-in-charge. (Note: -Butt hinges and necessary screws shall be paid separately)..(second class teak wood 35 mm thick shutter)

Providing and fixing of glass panes, of thickness 4.0 mm (weighing not less than 10 kg/sqm) including all type of fixture by way of wooden beading of 1 st class kail wood etc complete.

CEMENT PLASTER (IN COARSE SAND) 12mm Cement plaster of mix 1 : 4 ( 1 cement : 4 coarse sand)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives. New work (Two or more coats applied @ 1.43 litre/10 sqm. Over & including priming coat of exterior primer applied @ 0.90 litre/10 sqm.

Applying priming coat: With ready mixed pink or grey primer of approved brand and manufacture on wood work (hard and soft wood)

Preparing newly primed wooden surface for painting by way of filling of putty sand papering rubbing complete.

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade: Two or more coats on new work.

Cement concrete flooring 1:2:4 (1cement: 2 coarse sand: 4 graded stone aggregate) finished with a floating coat of neat cement including cement slurry and curing complete, but excluding the cost of nosing of steps etc. complete, 40mm thick with 20 mm nominal size stone aggregate.(50 mm thick)

Providing wood work in frames of walls,false ceiling, partitions etc. sawn and fixed in position :Budloo / Fir wood

Providing and fixing 12 mm thick tongued and grooved Pine wood (Soft Wood ) 4-5 inch in width panelling or wall panels in walls and celing includining all necessary fixtures including cornice with necessary screws, priming coat on exposed surface etc., complete. Brand - Rait Wood

French spirit polishing on wood work with ready mixed wax polish of approved brand and manufacture Two or more coats on new works including a coat of wood filler

Providing and fixing of KHATAMBANDI ceiling of first class budloo wood/fir wood excluding the cost of formwork which is to be paid separately Chaar gul ( LMR)

Providing and fixing 35 mm thick budloo wood in flooring

Providing and fixing plain jaffri mesh of 35x10 mm laths placed 35 mm apart (frames to be paid separately), including fixing 50x12 mm beading complete with : Second class teak wood

Providing hoisting and fixing trusses/purlins,rafter/posts.Post plated of truss components of Ist class budloo wood.fir wood including cost of screw etc Complete.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing ridges or hips of width 60cm overall width plain G. S. sheet fixed with poymer coated J. or L hooks, bolts and nuts 8mm G. I. limpet and bitumen washers complete. 0.80 mm thick with zinc coating not less than 275gm /m2 specifications as per engineer in charge

Providing and fixing 250mm wide eves boarding of budloo wood plained on one side

Providing fixing of base plate joint plate U Clip and necessary nut bolt Etc.

Providing and fixing stainless steel (Grade304) railing made of Hollow tubes, channels, plates etc.,

Providing and laying vitrified floor tiles in different sizes (thickness tobe specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622 of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1cement :4 coarse sand) including grouting the joints with white cement and matching pigments etc. complete i.e Size of tile 600x600 mm

P/F 1st quality ceramic glazed wall tiles conforming to IS:15622 (thickness to be specified by the manufacturer) of approved make in colours, shades except burgundy bottle green, black of any size as approved by engineer-in-charge in Skirting, risers of steps, and dados, over 12 mm thick bed of cement mortar 1:3 ( 1 cement : 3 course sand) and jointing with grey cement slurry @3.3kg/sqm including pointing the joint with white cement and matching pigments etc., complete.

Providing and fixing water closet squatting pan ( Indian type W.C. pan) with 100 mm sand cast Iron P or Strap, 10 litre low level P.V. C. flushing cistern including flush pipe (of approved make) "manually controled device (handle lever) conforming to IS:7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required. ( Orissa pattern white vitreous china W.C. pan of size 580x440 mm with integral type foot rests. JAGUAR/CERA Make)

Providing and fixing wash basin with C.I./M.S. brackets, 15mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever required: JAGUAR / CERA/HINDWARE Make

P/F of mirrors of superior glass with plastic moulded frame(of approved quality) and of required size and shape. With 6mm thick hard board backing. Rectangular Shape 1500 x 450 mm

Providing and fixing soil waste & vent pipePVC Pipe. 110mm dia (10 feet unit Length)

PVC Pipe. 75mm dia (10 feet unit Length)

PVC Bend 110mm dia

PVC Bend 75mm dia

PVC Tee 110mm dia

PVC Tee 75mm dia

PVC Collar 110mm dia

PVC Collar 75mm dia

PVC trap 110mm dia

PVC trap 75mm dia

PVC Socket 110mm dia

PVC Socket 75mm dia

PVC door junction 110mm dia

PVC door junction 75mm dia

Providing and fixing 3 layer Thermex Pipe PP-R (Poly propylene Random copolymer)pipes conforming to IS: 15801, UV stabilized and anti-microbial fusion welded, having thermal stability for hot and cold water supply including all PP-R plain and brass threaded Polypropylene random fittings. This includes testing of joints complete as per direction of Engineer-incharge.Internal work Concealed fixing the pipe with clamps at 1.00 meter spacing including cutting chases and making good the wall etc.PN-16 pipe , (32 mm dia)

PN-16 pipe , (25 mm dia)

Supply and installation of heigh quality and self regulating Heat Tracer for specialized heating solutions for winterisation of water pipe line including all accessories complete , including supply and insulation of circuit control panel with RCBO MCB THERMOSTAT (0-120) DEG C,power connector two way 6-sq mm w.p.splice connector w.p.tee connector and seal mounting kit w.pjb.j.i pipe strap 4” all adhesive tap roll 50 mm x 20 ml f.g adhesive tap roll (DANFOSS make or CHROMALOX any other approved brand as per direction of engineer in charge.

Supply and fixing of high quality 32mm thick Nitrile insulation tube for water pipe line of a[approved brand 2” size rock wool of apparent density 128 kg/ m3 on outer side of Nitrile tube of 50 mm thickness including aluminium duct cladding aluminium sheet gauge thickness 0.46 mm to 0.71 mm of approved quality and finished as per direction of engineer in charge (Nitrile Tube 32 mm > rock wool 50 mm > aluminium duct cladding 0.46 mm -0.71 mm.

Providing and fixing Wall mount Liquid Soap Dispenser of approved brand

15 mm C.P. brass tap with elbow operation lever of approved brand and manufacture

15 mm C.P. brass 2 in 1 tap of approved quality conforming to IS standards

15 mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931

15 mm nominal bore C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms

C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-incharge.

Single Lever Shower Mixer with 3-way diverter Concealed Divertor For Bath And Shower System including all accessories (KOHLER/ JAGUAR/ CERA)

Overhead Shower ( Maze Overhead Shower) 200X200mm Square Shape Single Flow (Body & Face Plate Stainless Steel with Chrome Finish) with Rubit Cleaning System including all accessories of approved quality conforming to IS standards ( KOHLER/ JAGUAR/ CERA)

450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

Supply installation testing and commissioning of Exaust Fan of approved brand (Havells/Bajaj/Crompton or any othet approved brand as per engineer in charge including all fixtures all complete

Supply installation of Soap dish approved brand as per engineer incharge

15 mm nominal bore of standard back type C.P. brass close hole basin mixer pillar tap of approved quality and make, weighing not less than 1.970 kg.

16 mm nominal bore of standard back type C.P. brass close hole wall mixer pillar tap of approved quality and make, weighing not less than 1.970 kg.

High water pressure S.S geyser connection pipe (2 feet long) of approved quality and make,

16 mm nominal bore of standard back type C.P. brass sink mixer of approved quality and make, weighing not less than 1.970 kg.

Providing and fixing accessories of standard and quality make of approved manufacturer including all necessary fixtures required.L-Drops for room door

Handles for door

Handels for window

T bolt for doors

T bolt for windows

Al drop for door

Providing and installation of PUF (Puf Insulated Tanks) water tank capacity 1000 ltrs of approved brand (SYNTEX OR ANY OTHER APPROVED BRAND) as per direction engineer incharge

Wiring for light point/ fan point/ exhaust fan point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC Channel, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Supplying and Fixing Double tone AC hot & Cold with Stablizer with all nessecessry fixtures as per the direction of engineer incharge.2 tone Approved brand

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC channel as required. A ) 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

b ) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

c ) 2X 10 sq. mm + 1X 6 sq. mm earth wire

d ) 4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Supplying/installation//testing and commissioning of (20 W) LED on ceiling round shape with complete accessories

Supplying and fixing of following sizes of hard class PVC conduit with accessories as required all complete job.

Supplying and fixing following size GI Modular box alongwith modular base & cover plate for modular switches in recess etc. as required.12 WAY

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required6 A switch

16 A switch

6 A socket

16 A socket

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)16 way MCB BOX

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as requiredsingle pole 6A

single pole 16A

double pole 32A

Change Over 32A

Add Sign Board RDD As per Designed by Site Engineer

Please Enable Macros to View BoQ information