Providing lift Irrigation Scheme to Village Bhavran and other areas in GP Amlehar from Beas river in Tehsil Nadaun, District Hamirpur

Excavation in foundations and trenches (for pipes and pits for other civil structures) upto all depths in all kinds of soil such as pick work, jumper work and saturated soil and paved surfaces including bailing or pumping out of water, chiseling or wedging out of same where blasting is prohibited in all leads and lifts including trimming and dressing of sides, leveling of beds to correct grade including shoring, strutting, planking timbering and dewatering wherever required, stacking usable and unusable material/soil separately and after laying jointing and testing of pipes, returning the usable soil in 15 cm layer by ramming and watering and then disposing of all surplus excavated soil/unusable material as directed within all leads and lifts including cost of diversion of traffic, night signal boards, fixing caution boards, crossing over trenches for access to houses, fencing etc. complete in all respects as per the direction of Engineer-in-charge.

Providing, Laying, jointing and testing & Commissioning of GMSERW pipe L-290 or X42 grade confirming to IS 3183:2007 at site in trenches bevelled ended BIS marked PIPE confirming to relevent codes & specification its equivalent latest with up to date ammendments of following dia with steel garde having wall thickness as mentioned below & capable of withstanding required test pressure as prescribed in BIS code , in random lengths of 5.0 to7.0 mtr. The pipe's ends shall be bevelled suitable for but welding , including the cost of jointing with butt welding confirming to IS 816-1969 or latest as appicable and with up to date ammendments (leak proof) in three layers at site of work with welding rods of standard make & all allied accesories whatever required for welding at site, tail piece, tees neds & other specials manufactured from parent pipes as applicable to the particular reach & of approved specifications as per site conditions and cutting of pipes wherever required as per site requirement i/c cariage in all leads & lifts as directed by Engineer-incharge. The pipe shall have zinc coating inside & outside confirming to IS 4736-1986 or latest with up to date ammendments & shall be engraved with IS 3183:2007 for GGMSERW pipe . The laying shall confirm to BIS 5822-1970 or latest with up to date ammendements to teh entire satisfaction of Engineer-Incharge (Earthwork ,Butt welded Joint & cost of MS flanged joints shall be measured & paid for seperately).

250 mmGMSERW Pipe IS/ISO:3183-2007 L290 or X 42 (4.80 mm thick)Booster & 1st stage

Providing and welding M.S. flanges @ 5% of joints, conforming to following tables as per IS 6392-1971 (Latest with upto date amendments) with plain end GMS/GMSERW pipe in requsite number of layers on both faces (i.e 2 layers on outer face and 1 layer inner face )to make the joint leak proof (The cost of providing and laying of GMSERW pipes to be measured and paid for seprately). The welding of flanges should conform to IS:816-1969 with electrodes as per IS: 814-1991 and required number of nuts and bolts conforming to IS 1364. including cost of gasket sheet nuts & bolts. The thickness of gasket sheet not less then 3.00mm conforming to IS 2712-1998. The work shall be done to the entire satifaction of engineer in charge with in all leads and lifts.

M.S. Flange 250 mm dia Table-11

Providing circumferential butt welded joints by electrical arc welding to GGMSERW pipe grade L-290 or X42 as per IS 3183:2012, welded in three number of weld runs so as to achieve the minimum effective throat thickness of weld conforming to IS 816-1969 specifications, by using welding electrodes of 2.5mm to 6.3mm of Advani Oerilikon (Adore)-CITOJET/ES/ESAB make,conforming to IS 814-1991, including Die pentration test, including fabrication ,laying & jointing requisite number of GMSERW/GMS bends at site of work complete in all respects, including manual/mechanical handling of pipes in all leads and lifts to the entire satisfaction of Engineer-in-Charge.

250 mm dia

Providing and fixing of Cast steel air valve of 50 mm dia (single wall type) of leader make ASA 150 MM dia complete in all respect in Rising Main