PROVISION OF SQUAD POSTS FOR TRAINING OF AGNIVEERS AT GARH RIF REGT CENTRE LANSDOWNE

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft/ disintigrated rock comlete all as specified and directed.

Excavating in trenches n'exc 1.5 m width and n'exc 1.5 m in depth for foundation or for shafts, well cesspits, manholes etc / for laying of cable/ pipe etc n'exc 10 sqm on plan and n'exc 1.5 m in depth and getting out in soft/ disintegrated rock complete all as specified and directed.

Returning, filling in, soft/ disintegrated rock including spreading, levelling, watering and well ramming in layers not exc 25 cm. complete all as specified and directed.

Removing excavated material soft/ disintegrated rock exc 250m but n.exc 500 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

Removing excavated material soft/ disintegrated rock exc 50m but n.exc 250 m and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

M&L for PCC (1:4:8) Type D2 (40 mm graded aggre-gate) as in foundations, filling and mass-concrete or sub base of floor/ hard standing/ footpath complete all as specified and directed.

M&L for RCC (design mix) M-25 (using 20mm graded stone aggregates) as in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles, raft etc and mass concrete complete all as specified and directed.

M&L for RCC (design mix) M-25 (using 20mm graded stone aggregates) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for formwork for rough finish to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L for formwork for rough finish to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L for mild steel TMT bars as in reinforcement, 10mm dia and over cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 5 to 10mm dia bars as in stirrups cut to length, bent to shape required including cranking, bending hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for 5mm thick plastering on brick or contrete surfaces, in CM (1:3), surface finished even and fair without using extra cement complete all as specified and directed.

M&L for preparing newly plastered surfaces of wall and applying two coats of cement base paint over a coat of cement primer complete all as specified and directed. Note :- The newly plastered surface must be prepared in a manner so that there should not be any impression of dent and it should be made even and smooth all as per satifaction of Engr-in-Charge. The cost of all materials, T&P and labour required for preparation of surface are deemed to be included in the rates quoted.

M&L for mild steel screw bolts (machine made) dia of neck length 16 to 20mm with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 22.5 cm and n exc 30cm long complete all as specified and directed.

M&L for mild steel Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment confirming Fe 410-W (Gde E- 250) quality A complete all as specified and directed.

S&F rolled mild steel section for Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc., conforming to Fe-410-W(Gde-E-250) quality-A complete all as specified and as directed. Note : The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete.

M&L for brick work with FLYASH bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6) complete all as specified and directed.

M&L for two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new steel surface over 10cm width or grith complete all as specified and directed.

M&L for 15mm thick plastering on fair faces of brick wall in CM (1:4), surface finished even and smooth with out using extra cement complete all as specified and directed.

M&L for mirror polished machine cut kota stone slab flooring 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and mirror finish polishing over and including 20 mm thick screed bed in cement mortar (1:6) complete all as specified and as directed Note:- The size of kota stone slab not less than 550mmx550mm (cut size except the location where balanced.)

Description same all as per item No 21 above but, as in skirting/ dado (10-12mm thick Kota stone) over and including 10 mm thick rendering in cement mortar (1:3) complete all as specified and as directed.

S&F Pre-painted galvalume aluminum zinc coated GI based corrugated steel sheet 0.50mm thick of any colour, having tensile strength of 550 Mpa, AZ-150 as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa, AZ-150 as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for 75mm thick PCC (1:3:6), type C-2 using 40mm graded stone aggregate as in plinth protection, surface finished even & smooth without using extra cement, with and including joint filling (Size 30mm deep x 10mm wide) with sealing compound grade-A at 3m interwal and corner complete all as specified and directed. Note : Joint to be provided at each interval of 3m and corner and cost of the same deemed included in quoted rate.

S&F rolled mild steel section for Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated conforming to Fe-410-W (Gde-E-250) quality-A complete all as specified and as directed. Note : The rates quoted allow for cutting to dead length where required, notching, drilling, fitting, riveting and/or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing and fitting angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing complete.

M&L for 60mm thick coloured rubber moulded glossy finish machine pressed precast concrete interlocking paver block, M-35 Grade with pre-polished, coloured/ laquar finish any shape and size, as approved confirming to IS 15658-2006 with and including over 25 mm thick stone dust/ sand cushining complete all as specified and directed.

M&L 150 mm thick PCC (1:4:8) type D2, (40 mm graded stone agg) as in sub base of floor complete all as specified and directed.

M&L for walling of random rubble, uncoursed well bonded, bedded and solidly hearted, stone masonary work built in CM (1:6) complete all as specified and as directed. Note :- Only quantity of PCC bond stone to be deducted from quantity of random rubble masonary.

M&L for PCC (1:2:4) type B-1, using 20mm graded stone aggregates, as in kerb/ benching/ coping, bed plates, for fixing of hold fast, water troughs and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

M&L for Precast PCC (1:3:6) type C-1, using 20mm graded crushed stone aggregate as in bond stones in lieu of stone bond stones, set in cement mortar (1:6), complete all as specified and directed.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surfacae not exceeding 40mm to face stone for Lime or sand stone and dressing of face beds and joints, as specified of random rubble walling, uncoursed or brought upto course complet all as specified and directed.

M&L for raised pointing in cement mortar (1:4) to random rubble masonary uncoursed or brought upto course complete all as specified and directed.

M&L for stone boulder or broken stone hand packing (Any thickness) at back of wall over arches etc and raising (or lowering) to the required level, complete all as specified and as directed.

S&F 110mm bore PVC (SWR) pipes single socketed in any length (6Kg/Sqcm pressure rating) and fixed in retainnig wall as spout (for weep holes) complete all as specified and as directed.

PIONEER REFRIGERATION AND ELECTRICALS (BID ID -3350366)

M/S Balaji Builders (BID ID -3364204)