PROVN OF SYNTHETIC VOLLEYBALL COURT, PROVN OF LADDER AT VARIOUS MESSES AND L/IN ACCN AND PROVN OF IRON CAGE WITH SHED FOR SOLAR WATER HEATERS AND PVC WATER TANKS AT VARIOUS LOCATIONS OF GANDHINAGAR UNDER GE (AF) CHILODA

Amount

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and as directed.

Rolling and consolidating formation surfaces in cutting Power roller exc 8 tonne not exc 12 tonne complete all as specified and as directed.

M&L 150mm thick (compacted thickness) WBM, with coarse aggregates of grading 2 (63 to 40mm size) or of grading 3 (50 to 20mm size), spread, rolled and consolidated to gradient and camber required granite, trap or basalt aggregate in two layers (7.5 cm each layer) complete all as specified and as directed.

Preparing black top surfaces by brushing with wire brushes for removing caked mud etc, sweeping with brooms & finally fanning the cleaned surface with gunny bages to remove all loose dirt etc complete all as specified and directed.

M&L applying evenly a priming/tack coat with bituminous primer using paving bitumen VG-10 at the rate 5 kg per 10 square meters complete all as specified and directed.

M&L Bituminous premix semi-dense asphaltic concrete 30mm consolidated thickness with 5.5% binder (Paving bitumen any penetration) content by weight of total mix, rolled & compacted to required camber & gradient complete all as specified and directed.

M&L Bituminous premix semi-dense asphaltic concrete (SDAC) 30mm consolidated thickness with 5.5% paving bitumen ( VG-30) as binder content by weight of total mix, using hot mix plant and mechanical paver as approved by the GE, rolled and compacted using 8 to 10 Ton power roller to required camber and gradient complete all as specified and as directed.

M&L Premixed sand seal coat with 0.06 cu.m. of sand mixed with 6.8 kg of bitumen using paving bitumen VG-10, applied and rolled to a uniform smooth surface complete all as specified and as directed.

Excavating in trenches, not exc 1.5 m wide and not exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. not exc 10 sqm on plan and not exc 1.5 m in depth and getting out in soft/loose soil complete all as specified and as directed.

M&L for PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in foundation, filling and mass concrete complete all as specified and as directed.

M&L Brick work with fly ash brick, old size bricks straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and directed

M & L for Rendering 15 mm thick on brick or concrete surfaces in cement mortar (1:4) finished even & fair without using extra cement complete all as specified and directed.

M&L for preparation of new plaster surface, concrete surface of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint complete all as specified and as directed.

Supply and Application of synthetic Flooring for Volley ball court with hybrid waterborne PU top coat finish on Asphult sub base. Following layer system are applied. (a) Concrete Primer (1- Layer) (b) Acrylic Resurfacer for filling and smoothing sub floor (1- Layer) (c) Triple Layer of Acrylic Rubber cushion (3- Layers) (d) Anti Skid Base Coat (1- layer) (base colour Coat) (e) Hybrid waterborne HPU-500 Top coat to protect flooring against UV Rays (2- layers) Make : Moldo Sports or equivalent as approved by GE.

M&L Line marking 50 mm wide white colour or Hybrid PolyUtherene (PU) paint and preferably in-laid or tufted into the Volleyball court. All inlaid markings shall be manufactured to the same specification as the main playing surface complete all as specified and as directed.

S&F 100 mm dia GI pipe for Volleyball court poles including all necessary accessories arrangement for net fixing complete all as specified and directed.

Removal of excavated soil to a distance n exc. 50 m and deposited where directed at a level not exc 1.5 m above the starting point complete all as specified and as directed.

S&F Mild steel works for posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc. flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or welding / riveting, etc and similar work conforming to Fe-290 Gde -E-165 complete all as specified and as directed.

S&F mild steel screw bolts ( machine made) with hexagonal or square heads at one end and screwed the other or screwed both ends each screwed end to be fitted with washers and one hexagonal or square nut , but length of bolt exc 5 cm and n exc 10 cm long and diameter of neck 10 mm complete all as specified and as directed.

Supply only chain link fencing MS galvanised fencing any size or type complete all as specifed and directed.

Fixing only Chain Link Fencing including line wires, any mesh, size and type of standards, rails, straining bolts, etc. including provision of binding wire complete all as specified and as directed.

S&F Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and as directed. Fe 410 -W (Gde- E- 250) quality- A

M&L for Preparing new steel surfaces exceeding 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed.

M&L for hardcore using broken stone or boulders not exc 63mm deposited, spread and levelled in layers not exc 15cm thick, watered and rammed to a true surface complete all as specified and as directed.

M&L 100mm thick cement concrete (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base complete all as specified and as directed.

M&L machine pressed precast cement concrete interlocking paver block any shape and size confirming to IS-15658-2006 of 60mm thickness M-35 Grade with grey cement and pigment jointed in neat cement slurry and pointed in cement mixed with pigment to match the shade of paver block complete all as specified and directed by Engineer-in-Charge.

M&L 25 mm sand filling under floors or in foundation including watering and consolidation complete all as specified and directed by Engineer-in-Charge.

M&L factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever complete all as specified and as directed.

Excavation in post holes or similar holes in soft/loose soil each not exc 0.5 cum getting out in soft/loose soil, returning filling in and ramming earth of broken rubble mixed with earth around, in layers not exceeding 25 cm, complete all as specified and as directed.

M&L for PCC (1:2:4) type B2 (40mm graded broken stone aggregate) as in foundations, filling and mass concrete complete all as specified and as directed.

M&L for Framed work such as grills, gratings, etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe-290, Gde-E-165 complete all as specified and as directed.

Cutting holes (Not exc 150 sq. Cm) into or through brick walls built in cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-l as required complete all as specified and as directed.

S&F 12 mm dia mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 10 cm but n exc 15cm long complete all as specified and as directed.

M&L for PCC (1:2:4) type B0 (12.5mm graded aggregate) as in roof kerbs or mud stops, rounded or chamfered on edges complete all as specified and as directed.

S&F pre-coated galvalume aluminium zink coating GI based corrugated steel sheet 0.50mm thick of colour having tensile strength of 550 MPA as in roof covering fixed with self topping screw complete all as specified and as directed.

JIYA CONSTRUCTION

TECH SERVE SOLUTIONS

ARTI CONSTRUCTION