Providing and Erecting E.I. and Street Lights on Zalod-Ahmedabad Highway Road ( From Guest House to Manav Restaurant ) At Balasinor, Ta. Balasinor, Dist. Mahisagar

Name of Work :- Providing and Erecting E.I. and Street Lights on Zalod-Ahmedabad Highway Road ( From Guest House to Manav

Restaurant ) At Balasinor, Ta. Balasinor, Dist. Mahisagar

QTY. UNIT RATE IN WORDS TOTAL

providing and erecting Mains with ISI marked, 1.5KV grade electrolyte multi

stranded, annealed copper conductor with heat resistant PVC insulated conforms

to IS 694, IEC - 227 erected in existing pipe of following size (Specifically for Rupees Seventy Paise

control panel, relays, power switchgears, motor starters & control wiring) with Seventy Only

required size of copper lugs, nuts and bolts if required.(e) One wire 6.00 sq. mm

Supplying and erecting Flexible PVC insulated multi strand multi core 1.1 kv

grade ISI marked copper wires of following size to be erected as directed.(h) 2.50 Rupees Ninety Seven

Sq.mm 3 core round PVC sheathed (Make:Havells,KEI,finolex,RRkable, Apar, Paise Ninety Seven Only

Supplying and erecting LED street light / Flood light fittings with High power

White LEDs wattage of 3 Watt and above assembled on single MCPCB,

efficiency more than 130 lm/w and corrosion free High pressure die cast

aluminum housing with smooth finish powder coated and heat sink extruded

aluminium with diffuser and Polycarbonate optics/ lenses, with toughened glass

with company mark/name engraved or embossed 160 to 270 V,Power Factor

more than 0.95, THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver efficiency > 85 %.( fittings Rupees Five Thousand

3a required LM-79 & LM-80 certificates)(NOTE: Below description have shown 68.00 Ea. 5581.26 Five hundred Eighty One

ranges of Wattage capacity of LED fittings.The Engineer incharge may select any Paise Twenty Six Only

wattage capacity between the ranges shown.) (A) Street Light (IP-65), Surge

protection -4KV integral and ,Light must have 440VAC line supply with over-

voltage protection. (iv) 90 - 119 watts Cat-lll (Make: Philips , Crompton,

Wipro,Jaguar, Havells) Fittings should be NABL tested and certified.

(B) Flood Light (IP-65), Surge protection -4KV integral and ,Light must have

Rupees Eight Thousand

440VAC line supply with over-voltage protection.(vi) 160 - 199 watts Cat-lll

3b 6.00 Ea. 8201.20 Two hundred One Paise

(Make: Philips , Crompton, Wipro,Jaguar, Havells) Fittings should be NABL

tested and certified.

Providing and erecting Approved make Four pole moulded case circuit breaker

having breaking capacity ICU of 25 KA. at 415 V,having normal current rating up

to 25 A to 100A. with Fixed thermal & magnetic release suitable to work on A.C. Rupees Six Thousand

4a supply 50 c/s. with all internal connections, spreader tinned copper & complete 1.00 Ea. 6790.23 Seven hundred Ninety

erected in existing 16 G.M.S. housing.ICS=100% of ICU only Cat III Paise Twenty Three Only

(Make:L&T,havells,Hager,C&S, Siemens)

Add Rs. 10% extra for housing/Encloser of MCCB

Rupees Seven Thousand

(Make:L&T,havells,Hager,C&S, Siemens)

4b 1.00 Ea. 7469.25 Four hundred Sixty Nine

Paise Twenty Five Only

Providing and erecting Approved make Earth fault Relay suitable to mount with

inter connection suitable to following size of moulded case circuit breaker having Rupees Five Thousand

5 CT ratio & MCCB rating as following along with shunt trip 220V AC. with all 1.00 Ea 5156.05 One hundred Fifty Six

internal connections & complete erected in existing M.S.housing.. (1) 15 A -100 Paise Five Only

A , CT Ratio 1/100

providing and erecting Miniature circuit breaker single pole 0.5A to 2A system

Rupees Two hundred

and having breaking capacity 10 KA to be erected in existing box. confirming to

6 68.00 Ea 297.95 Ninety Seven Paise Ninety

IS 8828/1996 with ISI Mark Cat III (Make:L&T,havells,Hager,C&S, Siemens)

Providing and erecting Annealed bare Copper wire 8 to 16 SWG. Rupees Seven hundred

7 2.00 Kg 794.87 Ninety Four Paise Eighty

Providing and erecting Pipe type earthing having 150 cms.long and 2.5 cms. dia. Rupees Three hundred

8 galvanised iron pipe with coupling and buch buried in specially prepared earth pit 68.00 Ea. 368.65 Sixty Eight Paise Sixty

complete with necessary 8 SWG earth wire. Five Only

For using salt and charcoal / coke as required for pipe type earthing. Rupees One hundred

9 68.00 Ea 171.70 Seventy One Paise

QTY. UNIT RATE IN WORDS TOTAL

Supplying & erecting earth pit of minimum bore dia.150mm size approved make

Earthing Electrode consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free hot dipped G.I.Pipes having Outer pipe dia of 50mm

having 80-200 Micron galvanising, Inner pipe dia of 25 mm having 200-250

Micron galvanising, connection terminal dia of 12mm with constant ohmic value

surrounded by highly conductive compound with high charge dissipation suitable

for following type of applications with chamber and heavy duty cover.

(A)(approved make OEM has to submit test certificate including value of earth

resistance of installation duly stamped and signed by agency and officer Incharge Rupees Four Thousand

10 has to ensure the value of earthing resistane mentioned in test Certificate) & 2.00 Ea 4591.46 Five hundred Ninety One

having back filling compound of (B) Inner chemical (CCM Compound)- Paise Forty Six Only

Resistivity:- 0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- <

volt at no load & dry form, Sulphar content:- <2%(C) Back fill Compound :-

Earthing compound should be capable to retain moisture for long time

Necessary test report must be submitted by Agency. (a) For Electrical Installation

up to 440V in normal soil

Length of pipe - 1 Mtr

Back filling compound - 1 Nos Bag of 15 Kg.

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand /

Solid Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps Rupees One hundred Sixty

11 or in existing trench / pipe of following size of cables (C) 4 core 10 Sq. mm 40.00 Mtr. 168.67 Eight Paise Sixty Seven

(Make:Havells,KEI,finolex,RRkable, Apar, polycab) Only

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in Rupees Two hundred

12a existing trench / pipe of following size of cables (B) 4 core 25 Sq. mm 2150.00 Mtr. 229.27 Twenty Nine Paise Twenty

(Make:Havells,KEI,finolex,RRkable, Apar, polycab) Seven Only

(C) 4 core 35 Sq. mm (Make:Havells,KEI,finolex,RRkable, Apar, polycab) Rupees Three hundred

Seven Paise Four Only

Making trench in Hard Murrum / Tar Road of suitable width of 90 cm or required

Rupees Seventy Four

13a depth for laying any size of cable or locating the fault all over the run and back 35.00 Mtr. 74.74

Paise Seventy Four Only

filling the same and making the surface as normal ground.

(B) If additional machinery like hammer driller or JCB use [Add] Rupees Four hundred

13b 2030.00 Mtr. 432.28 Thirty Two Paise Twenty

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary connecting accessories

Rupees Sixty Two Paise

14 of same material at required depth in existing trench for laying of cable. below 2173.00 Mtr. 62.62

ground / road surface for enclosing cable (A)50 mm outer dia

Providing and, fixing heavy duty flange type brass cable gland with rubber ring for

Rupees Thirty Eight Paise

15a PVC insulated armoured cable complete with out going tails, insulating tape etc 2.00 Ea 38.38

Thirty Eight Only

for following size of cables.(C) 2 to 4 core 10 Sq. mm

(E) 2 to 4 core 25 Sq. mm Rupees Fifty One Paise

Providing and, fixing heavy duty flange type brass double compression type

cable gland with rubber ring for PVC insulated armoured cable complete with out Rupees Seventy Five

going tails, insulating tape etc for following size of cables.(B) 3 & 1/2 core 35/50 Paise Seventy Five Only

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of

following size evenly crimped with high pressure tool & connected to switchgear Rupees Thirteen Paise

terminals with brass/cadmium plated nut bolts in an approved manner. (B) 10 Thirteen Only

(C) 16/25 Sq.mm. Rupees Fifteen Paise

(D) 35/50 Sq.mm. Rupees Twenty Paise

Supplying and erecting approved make Octagonal pole made from HR sheet

steel. The pole should be made as per IS. and shall be coated with hot dip

galvanizing as per IS 2629/2633/4759, suitable suspend local wind speed with

integral Junction box consist of terminal plate of min 6mm Hylam sheet, standard

profile 35mmX7.5mm Din-Rail for MCB Mounting, stud type terminal and Rupees Fifteen Thousand

18 arrangement for cable termination to be erected With Suitable foundation 68.00 Ea 15411.59 Four hundred Eleven Paise

(Included) as per details given by manufacturer considering site requirement.(G) Fifty Nine Only

8 Mtr. Long 70 mm Top X 155 mm bottom dia, 3 mm thickness with

260mmX260mmX16mm base plate, 4-M20 Bolts and 600mm long with

necessary G.I. J Bolts Approx Pole weight 84 kg

(Make:Transrail,Bajaj,Utkarsh,Ambica)

QTY. UNIT RATE IN WORDS TOTAL

Providing and erecting Street Light pole bracket comprising main B Class GI pipe

of 4.2 cm/require outside dia. complete with suitable B Class G.I. sleeve tubing of

approx. 45cms.length and suitable for 76.5 mm /80mm / required size of pole top

Rupees Six hundred Eighty

having sufficient fasteners for fixing the brackets and having spread of 1.5.mtr.

19 68.00 Ea 683.77 Three Paise Seventy

length with 110 deg.with vertical plane & suitable welded stays, reducer and with

check nuts complete painted with one coat of Red oxide / PU base primer and

two coats of Aluminium / PU paint. paint with following nos of arms. [A] Single

Arm Bracket 1.5 Mtr

Supplying & erecting IP 55 grade following size section pillar fabricated from joint

less M.S. Sheet with angle iron legs made from jointless M.S. Angle with cable

clamps to be buried in ground to have appropriate erection to work uniform until

erected with cement concrete foundation and 45 cm high bricks work finishing

with plaster etc. hinged double door internally supported on both side, with

internal and outside looking arrangement with look and keys in duplicate 35 x 35 Rupees Three Thousand

20 x 5 mm M.S. Angle of Two Nos. one is welded and other with nut and bolt for 1.00 Ea 3595.60 Five hundred Ninety Five

erecting Bakelite sheet. Painting the Section Pillar inside and out side with three Paise Sixty Only

tank powder coated paint. section pillar roof should be without joint with water

leakage proof & tested as per IP 55 test & followed by IS 2147 of 1962 (B) 75 X

60 X 45 cm section pillar fabricated from 16 Gauge MS Sheet with angle iron

legs 45 cm long made from 35 X 35 X 5 mm thick MS angle.

Supplying and erecting HYLAM sheet on existing angle iron frame.for following Rupees Seven hundred

21 thickness (B) 4mm 2.00 Sq. Mtr. 771.64 Seventy One Paise Sixty

Supplying & erecting approved make Digital time switch having lithium cell

years operative and operate battery backup 1 channel day clock with 14 memory

programme, suitable to operate on 240V + 5%, 16A with, floating contacts Rupees Three Thousand

22 Minimum switching setup time 1 minimum & LCD display. Also comprised 1.00 Ea. 3168.37 One hundred Sixty Eight

permanent ON/OFF switching. Programming switches & housed in fire proof Paise Thirty Seven Only

thermoplastic enclosure & transparent cover erected as required with necessary

connection erected as directed.

Supplying & erecting power contactor ,AC3 duty for time switch complete erected

Rupees Two Thousand

as per direction Cat III (D) 4 pole 440V 40 Amp.

23 1.00 Ea. 2782.55 Seven hundred Eighty Two

Paise Fifty Five Only

Supplying, erecting, testing, commissioning approved make M.S. Polygonal High

Mast Pole having following general Specification.

(a) Polygonal Section fabricated from M.S. Plate confirms BSEN 10025 & Hot

deep galvanized minimum 65/86 micron (as per IS 2629 /1985) Lantern carriage

with ring and rubber lines for erection of luminaries of suitable site.

(b) Maximum telescopic section not more than four

(c) Double drum gear pipe motorized winch with 6mm dia S.S. Rod (For 16 mtr

and above size)

(d) Approved make L.E.D. aviation light = 1 No. Lightening arrestor = 1 No. with

necessary wiring of 2.5 sq.mm 5 core ISI copper cable Unarmoured.

24 (e) Bottom most section suitable for mounting reversible motor and switchgears 0.00 0.00 0.00 Rupees Only

having door not more than 1400mm x 300mm with waterproof gasket & hinges &

locking arrangement.

(f) Pole structure comprises suitable size of reversible motor, cable and

necessary switchgears with control panel. (g) bottom section shall have suitable

size of thickness supports ribs foundation bolts nuts etc.

(h) Item not comprises the cost of lanterns.

(i) Necessary Cement Concrete foundation as per IS including testing &

commissioning of the entire structure for following size of High Mast poles

[1] High Mast 12 Mtr. TOP A/F 105 mm, BOTTOM A/F 360mm, No. of Sec. No. - Rupees One Lakh Sixty

1, Bottom Thickness - 3 mm, Size of Base Plate - Dia 520 mm x 20 mm thick, Two thousand Eight

Foundation Bolt Size M24 x 850 mm, Qty - 6 Nos., Suitable for mounting Fitting hundred Fifty Eight Paise

of Light - 6 Nos. Forty Six Only

Supplying and erecting approved make suitable panel indicator LED type lamp, Rupees Forty Three Paise

lens cover, complete erected with necessary connections. Forty Three Only

AMOUNT PUT TO TENDER FOR RS.

Special condition

As there is replacement warranty has to provide for LED fitting for 3 years, so security Deposit an amount Rs. 37,953/- will be released only after completion

of warranty period or the replacement of defective LED fitting whichever is later. Further after issuing the notice to the contractor for replacement of defective

material, he has to take up the work of replacement within 10 days from the date of issuing the said notice, in case where the delay for replacement, the contractor

shall be penalized by Rs. 100/- per day for such delay. In case of non replacement of the defective material action will be taken against the contractor to keep his

registration in abeyance for three years and his full security deposit will forfeited to the Government.