PROVN OF FORAGE STORAGE ROOM, OPEN

Amount

Demolition of brickwork or stone boulder masonry built in cement mortar including all quoins, arches pillars etc Complete all as specified and directed by Engineer-In-Charge.

Demolition of cement concrete (unreinforced) in ground floors and pavings n.exc 15 cm thickness (below or above ground level) and removing unserviceable material outside defence area. Complete all as specified and directed by Engineer-In-Charge.

Taking down cement plaster or any description including raking out joints, hacking for key scrubbing down with water etc. Complete all as specified and directed by Engineer-In-Charge.

Surface excavation n'exc 30 cm deep and averaging 15cm deep and getting out in hard/dense soil. Complete all as specified and directed by Engineer-In-Charge.

M&L for plain cement concrete Type D-2, 1:4:8 (40mm graded agg) as in foundation, filling and mass concrete. Complete all as specified and directed by Engineer-In-Charge.

M&L for brick work with sub class 'B' (old size) brick , straight or curved on plan exceeding 6 metre mean radius built in cement sand mortar 1:4 Complete all as specified and directed by Engineer-In-Charge.

Returning/ filling with excavated earth, incl spreading leveling, watering and well ramming in layers n exc 25 cm thick with soft/loose soil Complete all as specified and directed by Engineer-In-Charge.

Removing of excavated soil n exc 50m and depositing where directed at a level not exc 1.5m above the starting point. Complete all as specified and directed by Engineer-In-Charge.

M&L for rendering 15mm thick in cement and sand mortar 1:4 on fair faces of brick work/stone work or cement concrete surfaces including finishing the surface even and smooth without using extra cement Complete all as specified and directed by Engineer-In-Charge.

S&F TMT bar 10mm dia and over cut to length, bend to shape required including cranking, bending spirally for hooping for cols, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.9 mm dia. Complete all as specified and directed by Engineer-In-Charge.

M&L for providing, cement concrete type B1, 1:2:4 (20mm graded aggregate) as in lintels upto 1.5m clear span cills, coppings, steps, seismic and other similar bands and the like including weathering,slightly rounded or chamfered angles and throating. Complete all as specified and directed by Engineer-In-Charge.

Formwork to sides and soffits of floor or roof beams haunchings, girders, bressummers, lintels, cantilevers, shelves including sup-ports, overhanges etc also splays between floors and beams etc rough finished flat. Complete all as specified and directed by Engineer-In-Charge.

M&L for hard core of broken stone or boulders of gauge n exc 63mm deposited, spread and levelled in layers n exc 15cm thick, watered and rammed to a true surface. Complete all as specified and directed by Engineer-In-Charge.

M&L for 75mm thick PCC 1:4:8 type D-2 (40mm graded aggregate) as in sub base for pavemet, path etc. Complete all as specified and directed by Engineer-In-Charge.

M&L for 75mm thick PCC (1:3:6) type C-2 using 40mm graded stone aggregate as in plinth protection, / sub bases etc. laid in alternate bays and similar works including finishing the surface of concrete topping even and fair, without using extra cement. Complete all as specified and directed by Engineer-In-Charge.

M&L for 75mm thick PCC (1:2:4) type B-1 usnig 20mm graded aggregate as in flooring including finishing the top surface even and smooth without using extra cement Complete all as specified and directed by Engineer-In-Charge.

S&F rolled mild steel framed work as in framing for calding glazing and the like fixed with angle cleats and connecting plates etc confirming to Fe 410-W (Gde E-250) quality B. Complete all as specified and directed by Engineer-In-Charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of cement paint over a coat of primer. Complete all as specified and directed by Engineer-In-Charge.

M&L for preparation of old treated surfaces of walls and applying one coat of oil emulsion paint over a coat of white wash. Complete all as specified and directed by Engineer-In-Charge.

M&L for rendering 20mm thick in cement mortar 1:4 on fair faces of brick work or concrete surface of wall in two layers {(First layer 10 mm thick in cement morter (1:4) and top layer 10mm thick in cement morter (1:4)} using water proofing compound and finishing the surface even and smooth without using extra cement Complete all as specified and directed by Engineer-In-Charge. (NOTE:-WPC shall be measured and paid separately)

Supply only Integral water proofing compound. Complete all as specified and directed by Engineer-In-Charge.

M&L for preparing old/ new plastered surfaces of wall and applying two coats of apex paint incld one coat of primer over one coat of Birla white putty 2mm thick including preparatory work and all scffolding arrangement to external wall surface in camouflage distruptive pattern. Complete all as specified and directed by Engineer-In-Charge.

M&L for complete removal of existing paint on old steel surface incl preparatory work of any description, over 10cm in width or girth , not otherwise described and applying two coats of synthetic enamel paint over a coat of primer. Complete all as specified and directed by Engineer-In-Charge.

Excavation in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm. Complete all as specified and directed by Engineer-In-Charge.

M&L for PCC 1:3:6 Type C-2 (40mm graded aggregate) in foundations, for fixing/ embeding the angle iron posts, filling and mass concrete. Complete all as specified and directed by Engineer-In-Charge.

S&F mild steel work as in post and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc: flat iron fillets (for securing wire mesh etc) including all necessary drilling, bolting or riveting, etc, and simillar work conforming to Fe-290 Gde E-165, Complete all as specified and directed by Engineer-In-Charge.

S&F for mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long, Complete all as specified and directed by Engineer-In-Charge.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails straining bolts, etc. including provision of binding wire. Complete all as specified and directed by Engineer-In-Charge.

Supplied only chain link MS galvanised fencing, any size or type. Complete all as specified and directed by Engineer-In-Charge.

S&F for galvanised 2 strand, steel barbed wire 2.24mm dia barbs at 75mm spacing and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. Complete all as specified and directed by Engineer-In-Charge. (Note : Each line of wire to be measured.)

Supply, laying and fixing of galvanized punched tape concertina coil (coil dia 1050mm at closed position) complete having galvanised spring steel core wire 2.50mm dia cold drawn steel galvanised punched tape of low carbon steel having series of sharp barbs uniformily punched along its length 550 Nos of barbs on pheriphery per revelution, crimped on steel spring core wire galvanised clips, GI steel wire handles hooked to coil for handling MS square bars spike hooked with coil having pointed face for anchorage closed of weight 11kg each coil including spreading of each coil min 10mtr length adequately tied to GI barbared wire fencing with GI wire of not less than 16 gauge at every 1000mm spacing tying of handles of succeding coil with preceding coil with GI wire not less than 16 Gauge, laying over 'Y' neck of angle iron posts. Complete all as specified and directed by Engr-In-Charge.

Supply and fixing reflective type sign board made of high intensity prismatic polycarbonate retro reflective sheeting fixed on one face/ side on 2mm thick aluminium sheet or 3mm ACP or 3mm FRP sheet, back side supported with mild steel frame using with angle iron 25x25x4mm (including two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer) Complete all as specified and directed by Engr-In-Charge.

S&F high intensity meridian marker made of polycarbonate body offering highest safety to motorist against median crashes, in various colour combinations, delinator, medians, bride wall and culverts escpecially during bad and wet weather condition. Complete all as specified and directed by Engr-In-Charge.

S&F raised pavement marker (Cat Eye) of size 100mm x90mmx20mm of polycorbonate lens working exclusively on micro prismatic lens type technology with marker body of colour white, yellow or red, fixed to the road surfaces using epoxy resin adhesive including taking out existing old one and making good the disturbed surface, Complete all as specified and directed by Engr-In-Charge.

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings. Complete all as specified and directed by Engr-In-Charge.

Dismantling boarding, any description, fixed in any position with nails. Complete all as specified and directed by Engr-In-Charge.

Dismantling framed work timber scantling 40 sq cm and over in section, in any position. Complete all as specified and directed by Engr-In-Charge.

Dismantling timber scantlings in fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section. Complete all as specified and directed by Engr-In-Charge.

Taking down chowkhats or frames (without taking off shutters from frame) n.exc 1.5 Sqm each. Complete all as specified and directed by Engr-In-Charge.

Taking down chowkhats or frames (without taking off shutters from frame) exc 1.5 Sqm but n.exc 4.0 Sqm each Complete all as specified and directed by Engr-In-Charge.

S & F of pre-painted colour galvalume aluminium zinc coating GI based corrugated steel sheet sheet 0.45-0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws Complete all as specified and directed by Engr-In-Charge.

S & F of pre-painted colour galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall/ridges , fixed with self tapping screws Complete all as specified and directed by Engr-In-Charge.

M&L for 18-20mm thick kota stone flooring machine cut mirror polished kota stone as in flooring over 20mm thick screed bed in cement and sand mortar 1:4, including rubbing and polishing. Complete all as specified and directed by Engr-In-Charge.

M&L for 18-20mm thick Kota stone flooring machine cut mirror polished kota stone as in skirting over 10mm thick screed bed in cement and sand mortar 1:4, Complete all as specified and directed by Engr-In-Charge.

S & F 2nd Class Soft Wood Weather boarding, clean sawn, thickness 20mm to 25 mm and rebated on thick edge to give 20mm laps and fixed. Complete all as specified and directed by Engr-In-Charge.

M&L for veneered decorative plywood 6 mm thick 5 ply, grade 1 (with BWR resin) with decorative face veneers on one faces; fixed with screws to timber frame work on walls. Complete all as specified and directed by Engr-In-Charge.

M&L for veneered decorative plywood 6mm thick 5 ply, grade 1 (with BWR resin) with decorative face veneers on one faces; fixed with screws to timber frame work on ceiling. Complete all as specified and directed by Engr-In-Charge.

M&L for 2nd class soft wood exc 13 cm & n exc 25 sq cm sectional area in plain fillets. square, rectangular or triangular in section, clean sawn, se-cured with nails or brads. Complete all as specified and directed by Engr-In-Charge.

M&L for clean sawn second class soft wood in scantling. Complete all as specified and directed by Engr-In-Charge.

M&L for 2nd class soft wood exc 3sq cm & n exc 6 sq cm sectional area in plain fillets. square, rectangular or triangular in section, clean sawn, se-cured with nails or brads. Complete all as specified and directed by Engr-In-Charge.

S& F in repair of stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples. Complete all as specified and directed by Engr-In-Charge.

S& F 2nd class hard wood plain, solid, straight chowkats and frames, wrought, framed rebated on the solid, rounded or chamfered, put together with glue pinned at joints including additional rebate for second shutter. Complete all as specified and directed by Engr-In-Charge.

S& F 2nd class hard wood 30mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, section 8, clause 8.24(a), supplied and fitted to chowkats. Complete all as specified and directed by Engr-In-Charge.

S& F 2nd class hard wood 30mm thick glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc.,divided into squares, with plain, chamfered or rounded, mitred and rebated sash bars with edges of sash bars framing moulded, any numbers fitted with cut and mitred beads for securing glass, etc. sizes of members of shutters as specified in SSR Part I, section 8, clause 8.24(a), supplied and fitted to chowkats. Complete all as specified and directed by Engr-In-Charge.

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square exc 0.5 sqm in each pane. Complete all as specified and directed by Engr-In-Charge.

S& F 2nd class hard wood 30mm thick plain, framed, panelled shutters (any number of panels), with panels of timber flat on both sides or feather edged or of veneered particle board medium density, wood particle board with commercial face veneers supplied and fitted to chowkats. Complete all as specified and directed by Engr-In-Charge.

S&F stainless steel butt hinges, size 100mm, medium weight Complete all as specified and directed by Engr-In-Charge.

S & F 75mm stainless steel butt hinges medium weight. Complete all as specified and directed by Engr-In-Charge.

S&F 150mm long extruded aluminium alloy handles, fabricated type, anodised. Complete all as specified and directed by Engr-In-Charge.

S&F 100mm extruded aluminium alloy handles, fabricated type, anodised. Complete all as specified and directed by Engr-In-Charge.

S&F 250mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed. Complete all as specified and directed by Engr-In-Charge.

S&F 100mm long aluminium anodised barrel tower bolts of extruded section and fixed. Complete all as specified and directed by Engr-In-Charge.

S&F 200mm long aluminium anodised barrel tower bolts of extruded section and fixed. Complete all as specified and directed by Engr-In-Charge.

S &F clamps, hold fasts and similar small articles conforming to Fe- 290 Gde-E-165. Complete all as specified and directed by Engr-In-Charge.

M&L for preparation of old wood and wood based surfaces of any description over 10cm width or girth and applying one coat of synthetic enamel paint. Complete all as specified and directed by Engr-In-Charge.

Excavation in trenches, n exc 1.5m wide and n exc 1.5m in depth, for foundation, etc or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in hard/dense soil. Complete all as specified and directed by Engr-In-Charge.

M&L for machine pressed precast interlocking paver blocks with grey cement and no pigment in any shape and size confirming to IS -15658-2006 of 80 mm thickness M-40 grade,laid and jointed,joints to be filled with dry sand over and including 50 mm thick sand cushion bed, Complete all as specified and directed by Engr-In-Charge.

M&L for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, stone masonry built in cement mortar 1:6. Complete all as specified and directed by Engr-In-Charge.

M&L for 50 mm thick cement concrete type B-1, 1:2:4 (20mm graded aggregate) as in sub base. Complete all as specified and directed by Engr-In-Charge.

M & L for reinforced cement concrete (nominal mix) type A1 (1:1.5:3) using 20mm graded aggregate as in foundations, including rafts, footings, foundation beams,plinth beams, bases for columns, etc, basement slabs, under-reamed piles and mass concrete. Complete all as specified and directed by Engr-In-Charge.

M & L for reinforced cement concrete (nominal mix) type A1 (1:1.5:3) using 20mm graded aggregate as in beams, cantilevers, bressummers, lintels over 1.5 m span . Complete all as specified and directed by Engr-In-Charge. (Note: The rates includes for use of formwork straight or curved)

Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits of foundation and plinth beams and similar work, vertical or to batter for flat rough finished surfaces of concrete. Complete all as specified and directed by Engr-In-Charge.

S&F TMT bars 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binders cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including 0.9 mm dia annealed mild steel wire. Complete all as specified and directed by Engr-In-Charge.

M&L for 15mm thick rendering on fair faces of brick work or concrete surfaces in CM 1:6, using liquid water proofing compound, finished rendering surfaces even and smooth (without using extra cement). Complete all as specified and directed by Engr-In-Charge. (NOTE:-LWPC shall be measured and paid separately)

Supply only liquid water proofing compound (Make: Pidilite :101 LW+ or equivalent). Complete all as specified and directed by Engr-In-Charge.

M&L for preparation of new plastered surfaces of any description and applying three coats of white washing on wall cornices etc Complete all as specified and directed by Engr-In-Charge.

S & F rolled mild steel in plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, without any attachment of Fe 410-W (Gde E-250) quality-A. Complete all as specified and directed by Engr-In-Charge.

S & F 16-20mm dia mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to fitted with washers and one hexagonal or square nut, of length exc 5 cm and n exc 10cm long of 16 to 20mm dia. Complete all as specified and directed by Engr-In-Charge.

S & F roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. of Fe 410-W (Gde E-250) quality-A. Complete all as specified and directed by Engr-In-Charge.

M&L for screed bed or bedding layer of cement mortar 1:6, 20 mm thick for laying floor finishes. Complete all as specified and directed by Engr-In-Charge.

M&L for chequered concrete tile 20cmx 20cmx 25 mm thick set with grey cement and pigment jointed and pointed in neat cement slurry in floors. Complete all as specified and directed by Engr-In-Charge.

M&L for 15mm thick cement plaster in cement mortar 1:4 on stone masonry on surface other than fair faces of brick work and finished surface even and smooth without using extra cement. Complete all as specified and directed by Engr-In-Charge.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints, as specified of random rubble walling lime and sand stone, uncoursed or brought upt to courses with maximum depression on face from straight edge held against the dressed surface not exceeding 20mm. Complete all as specified and directed by Engr-In-Charge.

M&L for plain cement concrete (1:3:6) type C2 using 20mm graded crushed stone aggregate) as in surface channel/drains etc. Complete all as specified and directed by Engr-In-Charge.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/stopped ends etc. Complete all as specified and directed by Engr-In-Charge.

E&M PORTION :- Taking down carefully any type point wiring (light, fan, socket or power) complete including conduits/casing- capping with fittings such as light fittings, sockets, switches ceiling roses, board outlets etc and removing the materials/ debris and making good disturbed surfaces of walls, floor etc to match with the existing surface.Complete all as specified and directed by Engr-in-Charge.

M&L for point wiring complete with FRLS 1100 Volts grade, 1.5 Sqmm PVC insulated and unsheathed copper conductor single core cable drawn through and including 25 mm medium grade ISI marked PVC casing caping with all accessories such as bends, elbow, reducers , junction boxes /MS boxes duly painted /PVC box factory made ractangular in shape as required with top cover 3 mm thick plastic laminated sheets of required size, fixed with screws, for housing switches, sockets, regulators etc, including 1.5 sqmm PVC insulated and unsheathed copper conductor cable as earth continuity wire connected to common earth dolly Complete all as specified and directed by Engr-in-Charge, for the following :- (a) One light/ceiling fan point controlled by one switch.

All as per item no.87 above but one switch socket combination 5 Amps on independent board.

M&L for point wiring in non-metallic PVC casing & caping including all fitting with 2.5 Sq mm size multi stranded FRLS copper conductor cable including clamps, screws gutti /plug etc PVC unsheathed cable into and including wooden board/sheet steel box of 1.6mm thick with bakelite sheet 3mm thick and PVC insulated fire retardant cable of size 2.5 Sq mm as earth continuity conductor. Complete all as specified and directed by Engr-in-Charge.

S & F switch piano flush type single pole, one way 5/6 Amp.Complete all as specified and directed by Engr-in-Charge, Make:- Legrand/ Siemens/ Schneider / L&T.

S & F s/socket outlet flush type two in 1, 3/5 Pin, 5 Amp, 230 Volts Complete all as specified and directed by Engr-in-Charge. Make:- Legrand/ Siemens/ Schneider / L&T.

S&F switch socket combination flush type multipurpose 3/5 pin suitable for 15 Amp Complete all as specified and directed by Engr-in-Charge, Make:- Legrand/ Siemens/ Schneider / L&T.

S & F switch paino flush type single pole one way , 15 Amp, 230 Volts Complete all as specified and directed by Engr-in-Charge. Make:- Legrand/ Siemens/ Schneider / L&T.

S&F ceiling rose surface bakelite surface 65x50 mm, 3 trminals fixed on wall/ceiling and including PVC block.Complete all as specified and directed by Engr-in-Charge.

S&F in repairs 1 X 18 W LUMILINE Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver. Make of Bajaj / Philips/Havells.

S&F in repairs lamp holder/angle batten, PVC/Polycarbonate type with cord grip cap suitable for pendant fittings.Complete all as specified and directed by Engr-in-Charge.

S&F in repairs LED lamp of 7 watts 230 volts type. Complete all as specified and directed by Engr-in-Charge. Make:Syska /GE /Philips /Crompton

S&F in repairs environmental friendly ultra modern energy saving surface mounted decorative oval bulk head edge-lit LED luminaire comprising of high brightness LED 10 W 6000 k. Make:Syska /GE /Philips /Crompton

S&F in repairs MCB DB 2 way sheet metal enclosure SPN 240 volts, 50 Hz, with IP-42 protection, double door with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting Complete all as specified and directed by Engr-in-Charge Make:ABB/Siemens/Hager/Schneider.

S&F in repairs MCB DB 8 way sheet metal enclosure SPN 240 volts, 50 Hz, with IP-42 protection, double door with 200 Amps standard bus bar of suitable size and common neutral link all enclosed in standard sheet flush mounting Complete all as specified and directed by Engr-in-Charge Make:ABB/Siemens/Hager/Schneider.

S&F in repairs MCB single pole and neutral 40 Amp,240 volts, fixed in DBs. Complete all as specified and directed by Engr-in-Charge, (Make:- Havells/ Standard/ Schneider)

S&F in repairs MCB single pole, 6-32 Amp,240 volts,. Complete all as specified and directed by Engr-in-Charge, (Make:- Havells/ Standard/ Schneider)

M&L for Earthing complete with galvanized steel earth plate electrode 600mm x 600mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanized earth wire of 4 mm dia (up to 7.5 m in length from earth plate ) by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate no.3 of SSR part I including necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 8mm dia at 150mm c/c in both ways as reinforcement, watering funnel, 20 mm dia light grade for protection of earth electrode, 20 mm dia GI pipe light grade for watering complete all as specified and as directed by Engineer in charge and tested on completion. (Note : The rate is inclusive of necessary earth work, RFR and removal etc )

Supply, lying and fixing or passing through pipe in repairs 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed inservice connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, twin core cable flat or circular of size 10 sqmm .Complete all as specified and directed by Engr-in-Charge.Make: Polycab/Finolex/KEI /Universal .

Supply and fixing in repair House service bracket (hook type complete with 3.0m long G.I. pipe 40mm dia Med. grade, two nos 90 degree bends. M.S. hook and stay or guy complete all as specified and directed by Engr-in-Charge.

Supply, lying and fixing or passing through pipe in repairs 1100 volts grade heavy duty cable PVC insulated aluminium conductor, served with inner sheathing of PVC tape and overall PVC sheathed inservice connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, twin core cable flat or circular of size 6 sqmm .Complete all as specified and directed by Engr-in-Charge.Make: Polycab/Finolex/KEI /Universal .

M/S IQ ENTERPRISES

M/s Mohammad Shafi Malik

M/S GHULAM NABI LONE AND BROS