ADDITIONAL ALTERATION AND CONSTRUCTION OF TOILET AND SPECIAL REPAIR AT CERTAIN BLDG AT HASIMARA MIL STN UNDER GE (S) BINNAGURI

Amount

Schedule 'A'

Dismantling of plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

Dismantling timber scantlings 40 sqcm and over in section as in framed work in any position complete all as specified and directed..

Dismantling of wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards / slabs/ blankets any thickness including cover fillets complete all as specified and directed.

Demolition of reed, lathing, single or double, including battens and plaster or chicken wire lathing complete all as specified and directed.

Demolition of brick work or stone/boulder masonry built in cement mortar including all quoins, arches, pillars etc complete all as specified and directed.

Taking down chowkats or frames not exc 1.5 Sqm each with shutters ( with out taking off shutters from the frames) complete all as specified and directed.

Taking down chowkats or frames exc 1.5 sqm but not exc 4.0 Sqm each with shutters ( with out taking off shutters from the frames) complete all as specified and directed.

M&L for RCC (nominal mix) 1:1.5:3 type B1 using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified and directed . Note - Reinforcement and form work shall be measured and paid separately.

M&L for RCC (nominal mix) 1:1.5:3 type B1 using 20 mm graded stone aggregate as in beam, cantilevers, bressummers, lintels over 1.5 m span and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

M&L for RCC (nominal mix) 1:1.5:3 type B1 using 20 mm graded stone aggregate as in chajjas and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

M/L for PCC Type B1 1:2:4 using 20mm graded stone aggregate as in coping & houching for manhole, including necessary form work complete all as specified and directed.

M&L for Precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work including necessary form work and set in CM 1:4 complete all as specified and directed.

Form work to sides and soffits of floor or roof beam, beam hauchings, girders, bressummers, lintels, cantilevers, shelves, for flat fair finished concrete surfaces complete all as specified and directed.

Form work to chullah hood, chajjas, troughs and similar items including edges etc for rough finished flat concrete surface complete all as specified and directed.

Mild Steel TMT bar 10mm dia and over cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Mild Steel TMT bar 5mm dia and over upto and including 10mm dia as in stirrups, spacers & binders cut to length bent to shape required including cranking, bending spirally for hoping for columns hooking ends and binding with & including Mild Steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L Fly ash Brick work using old size bricks with sub class 'B' bricks curved on plan with mean radius not exc 6m with bricks roughly cut to radius or bricks with wedge shaped joints built in cement mortar 1:6 complete all as specified and directed.

M&L Brick work using Fly ash bricks with sub class 'B' bricks straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

M&L for external rendering 20 mm thick in two layer, first layer shall be of 10 mm thick CM 1:6 and second layer of finishing coat shall be 10 mm thick in CM 1:4 mixed with WPC @3% by weight of cement on brick work or concrete surfaces of wall and finished even and fair complete all as specified and directed. Note-WPC shall be measured and paid separately.

M&L for rendering 15 mm thick in CM 1:6 on fair faces of brick or concrete surface of wall and finished even and smooth with out using extra cement complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St -240 and painted one shop coat of zinc chromate primer paint including preparation of surface at contractor workshop before fabrication complete all as specified and directed.

S&F MS steel Hollow section Square/rectangular as in roof truss ,purlin,rail etc etc complete using ERW or induction butt welded tubes conforming to IS 1161-1979 grade St -240 and painted one shop coat of zinc chromate primer paint including preparation of surface at contractor workshop before fabrication complete all as specified and directed.

S&F Rolled mild steel in Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) of grade Fe 410-W (Gde E-250) quality A complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in fixing in truss bolts including necessary form work complete all as specified and directed.

S&F pressed steel frames of size 125 mm x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including one shop coat of priming complete all as specified and directed.

M&L for PCC 1:3:6 type C-2 (using 40mm graded aggregate) as in hold fast block including necessary form work etc complete all as specified and as directed.

S&F 35 mm thick second class hard wood rail and style plain framed factory made paneled shutter (two panel) with lock rail and panel of 9 mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (part-I), kiln seasoned and chemically pressure treated complete all as specified and directed.

M&L Second class hard wood 30 mm thick factory made glazed and skeleton shutters, open rebated and prepared to receive glass , gauze etc with out sash bars, edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters as specified in SSR part I section 8 clause 8.20 (a) complete all as specified and directed.

S&F stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples complete all as specified and directed.

S & F for solid PVC door frame of size 50x47mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplied and fixing in opening as specified and shown on drawing made on section 8 of SSR 2010 Part-II complete all as specified and directed

S & F factory made solid panel PVC door shutter 30 mm thick style consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC “C” channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, S & F in the frame as shown on drawing in section 8 of SSR-2010 Part-II complete all as specified and directed

S&F steel ventilator with top hung shutter including hinges steel peg stay complete all as specified and directed

S&F 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.5 Sqm in each pane, complete all as specified and directed.

S&F Butt hinges, medium weight, cold rolled mild steel 75 mm long complete all as specified and directed.

S&F mild steel barrel tower bolts stove enameled black with bright bolt 150 mm long complete all as specified and directed.

S&F mild steel barrel tower bolts stove enameled black with bright bolt 125 mm long complete all as specified and directed.

S&F mild steel sliding door bolts, plate type, stove enameled black, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate of 250 mm length of bolt complete all as specified and directed.

S&F aluminium handles cast type anodised of 150 mm size complete all as specified and directed.

S&F aluminium handles cast type anodised of 125 mm size complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring fixed in floor, over all length of cover plate 140 mm complete all as specified and directed.

Demolition of cement concrete un reinforced in ground floor and paving n exc 15cm thick (below or above ground level) complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in floor finishes 40 mm thick laid in panels & finished even and smooth using extra cement complete all as specified and directed. .

M&L for glazed ceramic coloured tiles 300 X 450 X 7 mm thick on vertical surface such as dado / skirting / risers to steps etc jointed in neat cement slurry and pointed in white or coloured cement to match surface of tiles over and including rendering 10 mm thick in cement mortor 1:4 complete all as specified and directed. Note- (i) The size of tiles (except thickness) may be varied during execution without any price adjustment.

M&L for non skid ceramic coloured tiles of design as approved by GE 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in skirting and dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 10mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for non skid ceramic coloured tiles of design as approved by GE 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.38 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed in cement mortar 1:6 complete all as specified and directed.

M&L for applying two coats of acrylic distemper on newly plastered wall surface including preparation of surface over a coat of 1mm thick wall care putty complete all as specified and directed.

Material and Labour for preparation of new plastered surfaces and applying of two coats of cement base paint o wall surfaces complete all as specified and directed.

M&L for preparation of newly plastered surfaces of walls and apply three coat of white wash complete all as specified and directed.

M&L of two coat of synthetic enamel paint over one coat of red oxide on new steel surfaces of any description over 10cm in width or girth incl preparation of surfaces complete all as specified and as directed.

M&L for preparation of new or previously untreated surfaces of wood and wood based surfaces of any description, over 10 cm in width or girth and apply two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

S & F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in roof covering/cladding/ eaves board fixed with selp tapping screw complete all as specified and directed.

S & F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength 550 Mpa as in roof covering/cladding/eaves board fixed with selp tapping screw complete all as specified and directed.

M&L for non Asbestos ,fibre reinforced standard cement board as in ceiling ,4mm thick designer board (610mm x 610mm ) including hot dip GI heavy duty suspended ceiling grid system T-2420 all as specified and as directed

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate, 75mm thick in plinth protection laid in panels and finished even and smooth without using extra cement including necessary form work complete all as specified and directed. Note : Joints 12mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection.

Taking up or down steel tubing and connections including cleaning if refixing required for 15 mm bore of pipe complete all as specified and directed.

Taking up or down steel tubing and connections including cleaning if refixing required for 20 mm bore of pipe complete all as specified and directed.

S&F GI tubes medium grade with all fittings fixed to walls and ceilings or laid in floors of 15 mm bore of pipe complete all as specified and directed.

S&F GI tubes medium grade with all fittings laid in trenches of 20 mm bore of pipe complete all as specified and directed.

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 75 mm bore of pipe etc complete all as specified and directed.

M&L for PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors of 110 mm bore of pipe etc complete all as specified and directed.

S&F PVC (SWR) bends any radius of 75 mm bore with out access door complete all as specified and directed.

S&F PVC (SWR) bends any radius of 110 mm bore with access door complete all as specified and directed.

S&F PVC (SWR) P'Trap 110 mm bore complete all as specified and directed.

M&L PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S&F in repair vitreous china EWC white with 'P' or 'S' trap front or back inlet any pattern excluding flushing cistern & flush pipe but including plastic water closet seat black closed pattern with flat bottom and cover and hinging device complete all as specified and directed.

S&F in repair wash hand basin vitreous China, white, flat back (550x400mm) including cutting for and pinning ends of brackets and waste coupling of PTMT for basin etc with long screwed shanks and fly nuts, full threaded flage embedded in white cement incl PVC waste pipe with PTMT coupling for required length complete all as specified and directed.

S&F PVC 10 litres capacity valveless ,symphonic action type low level flushing cistern ,white including flush pipe, cantilever brackets ,inlet, ball valve, float and handle, PVC connection 15mm dia etc complete all as specified and directed.

S&F flush pipe 32 mm dia of polyethylene of low or high density or PVC, for low level cistern complete all as specified and directed.

S & F 15mm size PVC Connection with PTMT nut of length 450mm , complete all as specified and as directed.

Stop cock cast copper alloy with crutch or butterfly handle screwed down for iron pipe or for brass ferule of 15 mm bore, complete all as specified and directed.

S&F in repairs for 15mm bore dia of pipe pillar taps cast copper alloy, with capstan head chromium plated screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F in repairs Bib taps (long body )fancy type cast copper alloy, chromium plated for 15mm bore pipe, screwed for iron pipes or for brass ferrule all complete as specified and as directed.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F in repairs swivel shower of CP with shower arm for fixing with 15mm pipe complete all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and not exceeding 1.5m depth for foundation etc or for shafts, wells cesspits manholes pier holes etc not exceeding 10 sqm on plan and not exceeding 1.5 m depth in soft /loose soil etc complete all as specified and directed

Returning, filing in, including spreading, leveling, watering and well ramming in layers not exceeding 25 cm in soft/loose soil etc complete all as specified and directed

Removal of excavated materials not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting points etc complete all as specified and directed

Demolition and breaking up drain pipe (salt glazed ware, AC or reinforced concrete ) set in cement mortar for 150 mm internal dia of pipe complete all as specified and directed.

M&L for cement concrete bed to drain pipes including packing under and haunching against the sides of pipe after they are laid & tested for 150 mm bore of pipe with cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate complete all as specified and directed.

M&L for SGSW drain pipes laid in trenches of 150 mm internal diameter of pipe and jointed as specified complete all as specified and directed.

M&L for Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (½ round or ¾ section) in cement concrete 1:2:4 type B-1 smooth finished ,and reforming benching as required for 150 mm internal dia of pipe complete all as specified and directed.

M&L for PCC 1:4:8 type D2 using 40mm graded stone aggregate as in foundation filling and mass concrete complete all as specified and directed.

M&L for RCC (nominal mix) 1:1.5:3 type B1 using 20 mm graded stone aggregate as in foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under reamed piles and mass concrete complete all as specified and directed . Note - Reinforcement and form work shall be measured and paid separately.

M&L for RCC (nominal mix) 1:1.5:3 type B-1 using 12.5 mm graded stone aggregate as in slab supported on wall, beam and column in floors, roofs, landings, balconies, canopies and in shelves and similar work complete all as specified and directed. Note - Reinforcement and form work shall be measured and paid separately.

Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick (horizontal or sloping) for rough finished flat surface of concrete complete all as specified and directed

M&L for sand filling under floor or in foundations including watering and consolidation complete all as specified and directed

M&L Broken stone or boulders hardcore of gauge exceeding 63 mm but not exceeding 100 mm, deposited, spread and leveled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for 100 mm thick Cement concrete 1:4:8 type D-2 using 40 mm graded stone aggregate as in sub base complete all as specified and directed.

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in sub base flooring 25 mm thick surface finished even and rough to receive the topping layer complete all as specified and directed.

M&L for non skid ceramic coloured tiles of design as approved by GE 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles including 15 mm thick screed bed or bedding layer in CM 1:6 surface finished fair and even for laying floor finishes complete all as specified and directed.

S&F aluminium alloy, anodised sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy of 150 mm length of bolt complete all as specified and directed.

S&F aluminium, anodised, barrel tower bolts of extruded section 100 mm long complete all as specified and directed.

S&F PVC (SWR) junction single, (single T) equal or un equal of 110 mm bore of pipe with access door complete all as specified and directed

S&F aluminium handles cast type anodised of 150 mm size complete all as specified and directed.

S&F vitreous china EWC white with 'P' or 'S' trap front or back inlet any pattern excluding flushing cistern & flush pipe but including plastic water closet seat black closed pattern with flat bottom and cover and hinging device complete all as specified and directed.

S&F wash hand basin vitreous China, white, flat back (550x400mm) including cutting for and pinning ends of brackets and waste coupling of Bass CP for basin etc with long screwed shanks and fly nuts, full threaded flage embedded in white cement incl PVC waste pipe required length complete all as specified and directed.

S&F PVC 10 litres capacity valveless ,symphonic action type low level flushing cistern ,white including flush pipe, cantilever brackets ,inlet, ball valve, float and handle, etc complete all as specified and directed.

S&F for 15mm bore dia of pipe pillar taps cast copper alloy, with capstan head chromium plated screwed down high pressure with or without lettered 'Hot' or 'cold' with long screwed shanks and fly nuts, screwed for iron pipe complete all as specified and directed.

S&F Bib taps (long body )fancy type cast copper alloy, chromium plated for 15mm bore pipe, screwed for iron pipes or for brass ferrule all complete as specified and as directed.

S&F sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12mm wide with CP brass bracket guard railing 60cm long, complete all as specified.

S&F brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

S&F of PVC (SWR) floor trap, plain with grating including jointing with solvent cement outer dia 75 mm cement concrete (1:2:4), type B1 including complete all as specified and as directed.

M&L for PCC 1:3:6 type C2 using 40mm graded stone aggregate, 75mm thick in plinth protection laid in panels and finished even and smooth without using extra cement including necessary form work complete all as specified and directed. Note : Joints 12mm wide to the full depth of PCC shall be provided at every 3 meters and at every change of direction and shall be filled with mixture of bitumen and sand 1:3 by weight. Cost of this provision shall be deemed to be included in the quoted rate for concrete in plinth protection.

M&L for preparation of newly plastered surfaces of ceilings and apply three coat of white wash complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in lintels upto 1.5 m clear span, coping, benching, bed block, lintel band, plinth courses etc and similar work including weathering, slightly rounded or chamfered angles and throating including necessary form work complete all as specified and directed.

Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonry in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/DWC complete filled with brick bats of size 2.4 M dia X 3.0M effective depth Complete all as specified and as directed

M&L for PCC 1:2:4 type B-0 using 12.5 mm graded stone aggregate as in lintels upto 1.5 m clear span, cills, copings, bed plate, plinth courses, roof kerbs or mud stops rounded or chamfered on edges including necessary form work complete all as specified and directed.

S&F rolled mild steel plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes ,without and attachment of grade Fe 410-W (Gde E-250) quality A complete all as specified and directed.

S&F Mild steel bolts. purpose made. with hexagonal or square head one end and screwed the other, or screwed both ends; each screwed end to be fitted with washers and one hexagonal or square nut. Exc 30cm long

S&F Butt hinges, medium weight, cold rolled mild steel 100 mm long complete all as specified and directed.

M&L for PCC 1:2:4 type B-1using 20 mm graded stone aggregate as in sub base flooring 75 mm thick complete all as specified and directed.

M&L for PCC 1:2:4 type B-1 using 20 mm graded stone aggregate as in floor finishes 25 mm thick laid in panels & finished even and smooth using extra cement complete all as specified and directed. .

S&F Powder coated aluminium window sliding type three track (one gauge and two glazed shutter) aluminium sections weighing not less than 0.55 Kg per mtr for shutter including necessary jointing cleats, glazing cleats, rubber packing, screws, handle, locking arrangement etc complete and 5.5 mm thick tinted glass and stainless steel mosquito proof gauge complete all as specified and as directed.

S&F in repair powder coated anodised aluminium guard bar mesh size not less than 65 mm x 65 mm with guard bar of not less than 6 mm dia fixed to flat aluminium windows with & woolen rods straining bolts .and making good disturbed surface of wall complete all as specified and as directed.

S&F machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade with grey cement and no pigment complete all as specified and directed.

Taking down carefully aluminium point wiring for one light, socket or power etc incl all fittings such as switches sockets, holders, light fittings, fan regulators etc and making good the disturbed surface of wall ceiling Complete all as specified and as directed

M&L for concealed Point wiring controlled by one switch with 1.50 Sqmm (nominal area) FRLS, PVC insulated 1100 volts grade multi stranded copper conductor single core unsheathed cable and FRLS, ISI marked, PVC insulated 1100 volts grade multi stranded copper conductor single core of size 1.50 Sqmm as earth continuity conductor connected to common earth dolly, drawn through in and including rigid PVC conduit (Medium Grade) of suitable size, with all fittings, ISI marked and accessories, the pipe shall be fixed with clamping and shadle including provision of mild steel terminal boxes/Sunken boxes of suitable size made with 1.6 mm thick mild steel sheet recessed in wall with a coat of black bituminus paint and providing of with 3mm thick bakelite/PVC sheet ISI marked top cover , suitable for fixing of switches / sockets / regulators etc. fixed in recess of wall with brass chromium plated screws and cap washer complete all as specified and directed for the following :- (a) One light point controlled by one way switch 5/6 amps. Complete all as specified and as directed

(b) One ceiling fan/Exhaust fan point controlled by one way switch 5/6 amps Complete all as specified and as directed

(c) One socket out let 5/6 amps point on the same board Complete all as specified and as directed

(d) One socket out let 5/6 amps point on the independent board Complete all as specified and as directed

All as per item No 2 above but wiring with 2.5 sq mm single core copper conductor for one socket out let 15/16 amps point on the independent board Complete all as specified and as directed

S&F socket 2 in 1, 5 Pin, 5/6 amps, white ivory finish flash type complete all as specified and directed.

S&F of socket outlet 2 in 1, 5 Pin 5/15 Amp multipurpose 230 volt flush type complete all as specified and directed by Engr-in-Charge.

S&F switch piano flush type 5/6 amps single pole one way Complete all as specified and as directed

S&F switch piano flush type 15/16 amps single pole one way complete all as specified and directed.

S&F ceiling rose, bakelite, surface type, 220/240 volts, three terminals complete all as specified and directed.

M & L for lamp holder, insulated body, with back plate suitable for batten/angle fittings complete all as specified and directed.

S & F deluxe fan Electronic regulator AC 50 Hzs rotary step white/ivory finish complete all as specified and directed.

S & F in replacement of LED Lamp 9/10 W B22 retrofit type Complete all as specified and as directed

S & F Wall mounted slim LED batten 18W, with extruded aluminium housing, with integrated LED driver complete all as specified and as directed.

Supply and fixing LED street light fittings 45 watt in almunium PDC housing, toughned glass cover with IP66 protection complete all as specified and as directed.

Taking down sub main wiring of any type complete all as specified and directed.

M&L for sub main wiring with 3 run of 4.00 sqmm (nominal cross-sectional area) PVC insulated unsheathed single core cable of working voltage 1100 volts grade with stranded copper conductor drawn in PVC rigid non- metallic conduit complete all as specified and as directed. NOTE : (i) Three run of submain wiring cable alongwith 25 PVC conduit pipe shall be measured as one unit length.

Taking down old MCB DBs with MCBs/Main switches/wooden boards etc Complete all as specified and as directed

S&F Sheet metal enclosure for 8way Distribution Boards (DB’s), double door, single pole and neutral with 200 amps rated bus bar, IP-43 protection suitable for fixing MCB"S/isolators with and incl blanking plates complete all as specified and as directed.

S&F of MCB, Single pole and neutral 40 amps, 240 volts, ‘C’ curve, 10KA all complete as specified and as directed.

S&F MCB, Single pole, 5 to 32 amps, 240 volts, ‘C’ curve, 10 KA all complete as specified and as directed.

M & L for street light bracket made out of GI pipe light grade 25 mm dia 1.2 mtr length bent to shape and reduced to required size at top upto 1.2 mtr length by cutting, welding and well finishing including MS clamp of flat iron of size 25 x 5 mm suitable length 2 Nos complete with drilling, hole, fixing with nuts bolts and washers including painted with two coats aluminium paint over a coat of red oxide primer.

M&L in replacement for Earthing complete with galvanised steel plate electrode of size 600x600x6.30mm thick burried directly in ground with earth pit not less than 2.25 meter deep below normal ground level with top edge of plate not less than 1.5 meter below normal ground level connected to galvanised 4 mm dia earth lead by means of nuts bolts check nuts GI washers earth wire protected by galvanised iron pipe 15mm bore (Light grade) for building LT wall panel all as directed including concrete pit in PCC (1:3:6) type CI, precast RCC cover slab of size 30x30x10 cm with one handle for lifting made out of 8 mm diameter MS bar finnel wire mesh 20 mm bore galvanised iron pipe (medium grade) for watering charcoal or coke and salt in alternate layers necessary earth work in soft/loose soil with and including taking down the old one complete all as shown in electrical plate No 3 of SSR Part I 2009 including testing on completion all as specified and directed. Note: The Rate for Taking down the old unsv Earthing shall be deemed to be included in the unit rate.

M&L for Ceiling Fan 1200 mm sweep 240 volt 5 star rated complete with all accessories all as specified and directed.

S&F fan exhaust 300mm sweep, single phase heavy duty with their all accessories fixed properly on stone masonary wall surface with provisioning rag bolts, nuts, washers etc including making circular exhaust hile of 300mm dia, lauver shutter suitable for the same exhaust fan and which shall easily be operated with exhaust air pressure. any disturbed surface of wall shall be made good by cement work/ plastering and matching by existing colour white/colour wash and all metal parts of this item of work shall be painted with two coats of synthetic enamel paint over one coat of red oxide zinc chrome primer as well as writing the MES NO with white colour paint including connecting/ testing complete as

Shri T P ANIL KUMAR

M/S I P GROUP

MAJUMDER ENTERPRISE

CONSTRUCTION SHELTER

M/S. KUMAR CONSTRUCTION CO.

M/S RATHIN ENTERPRISES

M/S ROY ENTERPRISE

M/S DEY ENTERPRISE