129/41-22

3rd SEMESTER

To determine Mechanical Equivalent of Heat, J, by Callender and Barne’s constant flow method.

To determine the Coefficient of Thermal Conductivity of Cu by Angstrom’s Method.

To determine the Temperature Coefficient of Resistance by Platinum Resistance Thermometer (PRT).

To study the variation of Thermo-Emf of a Thermocouple with Difference of Temperature of its Two Junctions.

To calibrate a thermocouple to measure temperature in a specified Range using (1) Null Method, (2) Direct measurement using Op-Amp difference amplifier and to determine Neutral Temperature.

To minimize a given logic circuit.

Half Adder, Full Adder and 4-bit binary Adder.

Half Subtractor, Full Subtractor, Adder-Subtractor using Full Adder I.C.

To build Flip-Flop (RS, Clocked RS, D-type and JK) circuits using NAND gates.

To build JK Master-slave flip-flop using Flip-Flop ICs

To build a 4-bit Counter using D-type/JK Flip-Flop ICs and study timing diagram.

To make a 4-bit Shift Register (serial and parallel) using D-type/JK Flip-Flop ICs.

To design an astablemultivibrator of given specifications using 555 Timer.

To design a monostablemultivibrator of given specifications using 555 Timer.

4th SEMESTER

Measurement of Planck’s constant using black body radiation and photo-detector.

To determine work function of material of filament of directly heated vacuum diode.

To study V-I characteristics of PN junction diode, and Light emitting diode.

To study the V-I characteristics of a Zener diode and its use as voltage regulator.

Study of V-I & power curves of solar cells, and find maximum power point & efficiency.

5th SEMESTER

Study of Electron spin resonance- determine magnetic field as a function of the resonance frequency.

To show the tunnelling effect in tunnel diode using I-V characteristics.

To measure the Magnetic susceptibility of Solids.

To determine the Coupling Coefficient of a Piezoelectric crystal.

To measure the Dielectric Constant of a dielectric Materials with frequency.

To draw the BH curve of Fe using Solenoid & determine energy loss from Hysteresis.

To determine the complex dielectric constant and Plasma frequency of mental using Surface Plasmon Resonance (SPR)

Fabry-Perot Interfrometer

e/m measurement equipment by Helical Method

Electrical oven with temperature Control

Photomultiplier Tube Set

Helium-Neon Laser

Solid state Laser Source

Arduino Board (Mega)

Arduino Board (Due)

CCD Chips (moderate quality)

Magnetic susceptibility by Quinks method

8 bit DAC

Constant current sources

Michelson interferometer

Resistivity Measurement Apparatus

6th SEMESTER

To verify the law of Malus for plane polarized light.

To determine the wavelength and velocity of ultrasonic waves in a liquid (Kerosene Oil, Xylene, etc.) by studying the diffraction through ultrasonic grating.

To verify the Stefan`s law of radiation and to determine Stefan’s constant.

To determine the Boltzmann constant using V-I characteristics of PN junction diode.

Department of Microbiology

1. VeritiPro Thermal Cycler Specification: The Applied Biosystems™ VeritiPro™ Thermal Cycler delivers high-end performance and proven reliability with advanced temperature controltechnology and connectivity.Ramp rate of 6.0°C/sec, quiet fan, and ergonomicsoft-close lid, precise control over 6 independent temperature zones forPCR optimization on the 96-well block option,Control Software

2. Leica DM750 HD Digital Microscope 45° Trinocular 360 degree rotatable & c-mount, Eyepieces: 10x/20 Pointer eyepiece w/ eyeguard, 10x/20 Focusing eyepiece w/ eyeguard, Objectives:Hi Plan 4x, 10x, 40x, 100x oil objectives Condenser:Abbe Condenser 0.9Dry/1.25 Oil Rackless mechanical with one hand slide holder LED illumination – 6000 K temp, 25,000 h life at full intensity Resolution: 1920 x 1080 - Captured 5 M.P. Sensor:1/2.5" (0.5x C-mount recommended); High Speed SD Card (4GB)

Tender Specification for -80 freezer(-86 Degree) CONSTRUCTION FEATURES Unit must include: · Capacity: 480-490 Ltrs, External dimension should be within (HxWx D cm): 200 x 95 x 100, Must include NON-CFC REFRIGERANTS,17.3 cu. ft. capacity Upright, with (2) 1 horsepower compressors, Latch and handle for ergonomic handling and one hand operation with padlock capability, Durable Steel interior with Inner doors.,Down-feed evaporator, Adjustable solid Stainless Steel shelves·, Triple -sealing silicone door gasket,5” non-CFC foamed-in-place polyurethane insulation; 4.5” in door, Two 10” tubeaxial fans to provide maximum cooling of the compressor Housing, Heavy-duty dual wheel swivel locking casters., Automatic voltage compensator responds to high and low voltages, Powder coat paint for a durable surface, Service valves provided to allow easy recovery of refrigerants and field servicing., Front to back airflow with Removable, cleanable air filter, Hinged grill swings out for easy access to filter and battery, A vacuum relief port allows easy re-entry after door openings, 4” open x 12” long heavy duty hinge for ensuring positive closure and Un-interruptive service. *** Rest of the Specification is Given in the NIT Document***

RAMKRISHNA LAB SUPPLIER

SAHA SCIENTIFIC SUPPLIERS

BIOAPPS

ADVANCE INSTRUMENTS

ELCO SCIENTIFIC

S R ENTERPRISE

INTECH CORPORATION

Sikdar Scientific Agency

RAMKRISHNA LAB SUPPLIER

SAHA SCIENTIFIC SUPPLIERS

ADVANCE INSTRUMENTS

ELCO SCIENTIFIC

INTECH CORPORATION

BIOAPPS

Sikdar Scientific Agency

DETECH