DEPOSIT-Department of Women and Child Development ICDS District Level Cell Kannur-General Civil Work

Amount

Detailed Repair estimate

15.12.1:Dismantling doors, windows and clerestory windows (steel or wood ) shutter including chowkhats, architrave, holdfasts etc. complete and stacking within 50 metres lead:Of area 3 sq. metres and below

50.6.1.5:Solid block masonry using pre cast solid blocks ( Factory made) of size 30x20x20cm or nearest available size confirming to IS 2185 Part I of 1979 for super structure up to floor two level thickness 20cm and above in: CM 1:6 ( 1 cement : 6 coarse sand) etc complete

13.1.1:12 mm cement plaster of mix:1:4 ( 1 cement : 4 fine sand)

14.53.1:Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade:One or more coats on old work

13.61.1:Painting with synthetic enamel paint of approved brand and manufacture to give an even shade:Two or more coats on new work

50.9.12.1:Providing and fixing Thomson Multi wood board or equivalent make, in shelves with screws and fittings wherever required, edges to be painted with polyurethane primer (fittings to be paid separately) as per the direction of site Engineer-in-charge.

OD231705/2023-2024:Providing and fixing PVC sheet on to existing surface using adhesive complete as per the direction of the Engineer in charge including all cost of accessories, labour charges etc.

OD232074/2023-2024:Providing and fixing glazing in cubicles complete as per the directions of Engineer - in -Charge. With float glass panes of 5.50 mm thickness

21.1.1.2:Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS : 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminnium snap beading for glazing /paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge.(Glazing, paneling and dash fasteners to be paid for separately): For fixed portionPowder coated aluminium (minimum thickness of powder coating 50 micron)

21.1.2.2:For shutters of doors, windows & ventilators including providing and fixing hinges / pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately)Powder coated aluminium (minimum thickness of powder coating 50 micron)

21.2.2:Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS : 12823 Grade I Type II, in panelling fixed in aluminum doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of Engineer - in- Charge.Pre- laminated particle board with decorative lamination on both sides

21.3.1:Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of Engineer - in -Charge. ( Cost of aluminium snap beading shall be paid in basic item):With float glass panes of 4.0 mm thickness

9.80:Providing and fixing 50 mm bright finished brass cup board or wardrobe knob of approved quality with necessary screws.

9.165.1:Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.125 mm

9.115:providing and fixing powder coated telescopic drawer channels 300 mm long with necessary screws etc. complete as per directions of Engineer -in-charge.

OD232176/2023-2024:Providing and fixing 12mm thick Marine ply, backing or studding with screws, etc. complete ( Frames, backing or studding to be paid separately) as per the direction of site Engineer-in-charge.

OD232191/2023-2024:Providing and fixing 4mm thick veneer onto existing plywood using adhesive complete as per the direction of Engineer in charge including all cost of accessories labour charges etc as per the direction of engineer in charge.

OD232190/2023-2024:Preparation of wood surface for melamine polishing as per the following procedure: 1. Filling the holes and screw marks in the wood surface using wood filler and sandering the surface using 80 grade paper. 2. Applying first coat sanding sealer. 3. Filling joints using filler powder and sandering with 120 grade paper. 4.Applying second coat sanding sealer and sandering with 220 grade paper. 5. Applying one coat melamine sealer and sandering with 320 grade paper.

14.70:Melamine polishing on wood work ( one or more coat)

13.62.1:Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade:Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture .

21.13:Providing and fixing 100 mm brass locks ( best make of approved quality ) for aluminium doors including necessary cutting and making good etc. complete

9.114.1:Providing and fixing magnetic catcher of approved quality in cupboard/ward robe shutters, including fixing with necessary screws etc. complete.Triple strip vertical type

OD232239/2023-2024:Supplying and fixing Good Quality Blinds Curtain including Cost,Fitting Charges etc complete.

SANIL KUMAR T V

K M KUNHIKRISHNAN

VINODAN VALLUVAKKANDY

MANORANJ C.P

Bidder Name

VINODAN VALLUVAKKANDY

RAMAKRISHNAN K

MANORANJ C.P

K M KUNHIKRISHNAN

SANIL KUMAR T V