SPECIAL REPAIRS TO BLDG NO P 601 SINGLE JCO s ACCN OF 511 ASC BN AT AHMEDABAD CANTT

Amount

Taking down chowkats or frames with shutter (W/out taking off shutters) exc 1.5 Sqm but n.exc 4 sqm each.

Taking down chowkats or frames with shutter (W/out taking off shutters) not exceeding 1.5 Sqm each.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles and rubbish off the premises

Demolition of cement concrete (unreinforced) in ground floors and paving not exceeding 15cm thickness (below or above ground level) and disposing off the rubbish materials where directed complete all as specified or directed by the EIC

Roughening surface of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc.

Demolition of Concrete of any description and in any position not otherwise specifically providedthickness (below or above ground level) complete all as specified and directed.

Dismantling old u/s water tank of 1000 ltr capacity and removing to store

Taking down 15 mm dia GI tubing and connections, including removal to store

Taking down 20 mm dia GI tubing and connections, including removal to store

Taking down cement plaster on brick or stone walls, concrete walls etc including raking out joints,hacking for key, scrubbing down with water etc.

M & L 15 mm thick rendering cement plaster on brickwork or concrete surfaces in cement mortar 1:6 , finishing the surfaces even and fair (without using extra cement)complete all as specified and directed.

M & L 15mm thick rendering cement plaster on brickwork or concrete surfaces in cement mortar 1:4 , finishing the surfaces even and fair (without using extra cement) complete all as specified and directed.

M & L 10 mm thick rendering cement plaster on ceiling surfaces in any position in cement mortar 1:3 , finishing the surfaces even and fair complete all as specified and directed.

M & L white washing three coats to ceiling surfaces including preparation of new plastered untreated surfaces complete all as specified.

M & L for preparation of new plastered surfaces on walls and applying two coats of oil bound distember with one coat of wall care putty all as specified.

M & L for preparation of new plastered surfaces on walls and applying two coats of cement based paint on over one coat of primer on walls all as specified

M & L for complete removal of existing treatment and applying two coats cement based paint on over one coat of primer on walls all as specified and directed by Engr- in-Charge

M & L for complete removal of existing treatment and applying two coats of Oil bound distemper and one coat of wall care putty on old plastered and unplastered surfaces on walls all as specified and directed by Engr- in-Charge

M & L for complete removal of existing treatment and white washing three coats to ceiling surfaces all as specified and directed by Engr- in-Charge

S & F mild steel Gde Fe 410-O or Fe 310-O Chowkhats and frames of door shutters ( any type, size etc.) of angle, Tee or any section with MS plates/ gusset plates, cleats, hold fast etc including fixing (except provision thereof) of hinges by welding, all as specified and directed.

S&F 35 mm thick Factory made flush shutter , Solid core , construction with board core and plywood face panels commercial type on both sides.

M&L for Second class hardwood Glazed and skeleton shutters35 mm thick glazed & skeleton shutters, open rebated & prepared to receive glass, gauze, etc (without sash bars) edges of framing plain, chamfered or rounded, fitted with cut mitred beads for securing glass, etc size of members as specified in SSR Pt-I section 8 clause 8023 (a), in II nd class hard wood.

S & F Solid PVC Door frame of size 50 mmx 47 mm made out of 5mm plain colour PVC sheet reinforce with M.S square tube, high strength suppling & fixing in opening as per specification

S & F Factory made solid panel PVC door /cupboard shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

S&F 150mm size extruded aluminium alloy handles fabricated type anodised.

S&F 150mm extruded aluminium alloy tower bolts extruted sections anodised.

S & F Floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring of size 150 mm

S & F 250 mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed

M & L for Hacking out old broken glass (any thickness, size, quality or description) from wooden or metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones

S&F for sheet glass 3.0mm thick, ordinary quality and glazing with oil putty in square n exc 0.5 sq m in each pane

S&F figured glass 4mm thick pin headed type and glazing with oil putty / beads in square not exc 0.50 Sq.m in each pane, all as specified and directed.

S & F steel windows with side hung shutters including box type hinges with steel handle, steel peg stay & MS tower bolt 100mm long (2 nos in each leaf), Complete with glazing bars dovetailed or welded all as specified and directed.

S & F steel windows with side hung shutters including box type hinges with steel handle, steel peg stay & MS tower bolt 100mm long (2 nos in each leaf), Complete without glazing bars dovetailed or welded all as specified and directed.

S&F anodised aluminum Ventilators with fixed aluminium frame of size 65x40x1.98 mm thick fixed in vertical position with aluminium vertical members and half portion to be provided with 4 mm thick pin head glass and remaining portion to be louvered using 4 mm thick pin head glass and louvered portion covered with stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperture 1.4 mm incl necessary channel frame work, incl rubber gasket and aluminium beading complete all as specified.

S & F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

S & F in repair Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples

S & F 25 mm dia fancy type depary curtain rod with brackets and PVC fancy type ends etc fixed in repair complete all as spd and directed.

S&F aluminium anodised tubular towel rail 20mm dia D type and 60cm long including brackets fancy type brass chromium plated in repair

S & F 100mm size Hasp and staples, safety type, Aluminium anodised with mild steel hinge pin including bolt plate and fixed with screws.

S&F Stainless Steel butt hinges 100mm size medium weight cold rolled mild steel

M & L for preparation of old steel & iron surfaces of any description, over 10 cm with or girth not otherwise described and applying one coat of synthetic enamel paint over the exixting paint

M & L for preparation of new steel & iron surfaces of any description, over 10 cm with or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer

M & L for preparation of new wood and wood based surfaces of any description exc 10 cm with or girth with two coats of synthetic enamel paint over a coat of pink primer

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/sqm. This layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry

M&L for provinding PCC 1:5:10 type E2 using 40 mm graded stone aggregate for filing in sunken floor complete all as specified and as directed

Supply only Integral water proofing compound

S & F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls 110mm

S & F PVC (SWR) vent cowl 110mm

S & F PVC (SWR) branch piece 110mm single (double Y) equal or unequal with oval access door

S&F PVC(SWR) 75 mm dia soil waste and rainwater drainage pipes (6 kgf / sqcm) single socketed in any length with rubber ring joint laid in floor or fixed on wall all as spd & directed.

S & F PVC (SWR) bends any radius 75mm with access door

S & F PVC (SWR) bends any radius 110mm with access door

S&F 15 mm GI tubing medium grade with all fittings fixed to wall or ceiling or laid in floor :-

S&F 20 mm GI tubing medium grade with all fittings fixed to wall or ceiling or laid in floor :-

S & F in repairs 15mm bore pillar taps, fancy type cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed.

S&F 15mm PVC connection 600mm long with brass check nut on both sides screw to iron pipes.

S&F in repair for Stop valves 15 mm size, cast copper alloy, fancy type, chromium plated, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F in repairs for 15 mm Bib taps, fancy type, chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed

S & F in repair 15 mm swivel shower roses of PTMT incl fixing to steel pipe or union.

S & F in repair PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets 10 ltr

S&F in repair vitreous china wash down water closet pan (Pedestal pattern) coloured including fixing bolt and plastic water closet seat black closed pattern with flat bottom cover with MS chromium plated hinging devices to matching colour.

S & F in repairs Vitreous China wash basin, flat back, size 550x400 mm white, excluding taps, waste, chain and plug and porcelain stopper but including brackets fixed in repairs

S&F in repairs health faucet spray type brass, chromium plated, and 1.5 m long PVC flexible pipe complete all as specified and directed.

S & F Glazed ceramic tiles in vertical surface 450X350X7mm thick as in dados and skirting set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including rendering 10mm thick in CM 1:4, complete all as specified and directed. complete all as specified and directed.

M & L Vitrified light shade Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and over and including screed bed or beeding layers of mortar 15mm thick in CM 1:6 in floors, complete all as specified and directed. complete all as specified and directed.

Ditto as per item no above but in vertical surfaces such as skirting over and including 10 mm thick backing coat in cement mortar 1:4 -ditto-.

M & L for non skid ceramic (colored) tiles 7 to 8 mm thick as in floor area of each tile exceeding 0.06 Sqm but n exceeding 0 .11 Sqm , set and jointed in neat cement slurry and pointed in white or colored cement to match over and including screed bed or beeding layers of mortar 15mm thick in CM 1:6 in floors, complete all as specified and directed.

S&F PTMT square grating with waste hole 150mm size for trap in repairs

S&F in repair 20mm dia Ball valves high pressure of PTMT with epoxy coated Aluminium rod & highdensity plastic ball screwed for iron pipe and fixed. (Minimum weight 20mm -210 gm)

S&F in repair 20 mm bore gun metal globe or gate valve with iron wheel heads screwed both ends for iron pipe as in repairs.

Taking down old damaged water proofing treatment from roof surface of any description incl broken out/ loose plaster/PCC (any thickness), scrubbing down with water etc. M & L APP based polymeric membrane minimum weighing 3.0kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) laid by torch application over one coat of bituminous primer @ 0.30 kg/sqm over and including 15 mm thick cement plaster in CM 1:4 including water proofing compound @2% by weight of cement, applying two coat of aluminium paint as per the makes approved by the Engr-in- charge including disposal of debries exe. 50 mtr and n.exe. 100 mtr from starting point all as specified.

M & L for PCC 1:2:4 type B0 using 12.50 mm graded stone aggregate in roof etc as levelling coarse etc. all as specified and directed by Engineer-in charge

S&F 1000 Ltr Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete.

M&L PCC type C-1 Mix 1:3:6 (20mm graded stone aggregate), 75mm thick in plinth protection/path finishing the surface even and smooth without using extra cement with joints filled with bitumen grade 85/ 25 and sand in equal proportions by weight complete all as specified and directed.

M&L for pre-polished kota stone slab 20-25mm thick as in shelves including cutting groves in wall making good disturbed surface, matching with existing surface etc; rubbing and polishing complete all as specified

M&L for machine cut kota stone slab 20-25mm thick as flooring/ landing laid and jointed with grey cement slury incl rubbing and polishing , over and including 20 mm thick CM 1:6 screed bed complete all as spd and directed.(Note: All exposed side of kota stone slab to be rounded)

M&L for machine cut kota stone slab 20-25mm thick as in riser of steps, skirting, dado laid jointed with grey cement slurry f incl rubbing and polishing , over and including 10 mm thick CM 1:4 screed bed complete all as spd and directed.(Note: All exposed side of kota stone slab to be rounded)

M&L for Treatment of soil under existing floors using emulsion @ one litre per hole,300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors

Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron.

Taking down carefully surface aluminium/copper point wiring with PVC casing-capping (light, fan, socket, bell or power) including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc and making good disturbed surfaces complete.

M&L for point wiring with 1100 volts grade PVC insulated FR-LSH multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal boxes of thickness not less than 1.20 mm and white modular mounting cover plates with frame for mounting modular switches, sockets, fan regulators etc. complete for the following :-

One light point controlled by one switch.

One fan / exhaust point controlled by one switch.

One socket outlet 6 amp controlled by one switch on independent board.

One socket outlet 6 amp controlled by one switch on same board with other switches.

One bell point controlled by one switch.

M&L for point wiring with 1100 volts grade PVC insulated FR-LSH multistranded copper conductor cable 2.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings/fixing accessories and sunken galvanized pressed steel terminal boxes of thickness not less than 1.2mm covered with 3mm thick phenolic laminated white shite cover for one 16 amp socket outlet controlled by one switch on independent board.

S&F angle holder, insulated polycarbonate body with back plate, complete, Make- Havells Reo/ Anchor Penta PC / SSK as approved.

S&F modular switch piano button single pole one way 6 amp 1 module all as per Legrand Mylinc Cat Ref No 675501 or equivalent in Schneider Zencalo or MK Blanze as approved.

S&F modular switch piano button single pole one way 16 amp 1 module all as per Legrand Mylinc Cat Ref No 675511 or equivalent in Schneider Zencalo or MK Blanze as approved.

S&F modular bell push, 6 amp, 1 module all as per Legrand Mylinc cat ref no 675504 or equivalent in Schneider Zencelo or MK Blenze as approved.

S&F modular socket outlet 2 in 1, 2 & 3 pin, 6/16 amp, combined 2 module all as per Legrand Mylinc Cat Ref No 675555 or equivalent in Schneider Zencalo or MK Blanze as approved.

S&F modular socket outlet 2 in 1, 2 & 3 pin, 6 amp, combined 2 module all as per Legrand Mylinc Cat Ref No 675550 or equivalent in Schneider Zencalo or MK Blanze as approved.

S&F bell multi music type, AC, 240 volts complete. Make-Anchor or SSK or Havells Reo as approved

S&F modular hum free electronic step fan regulator 100 Watt, 2 module all as per Legrand Mylinc Cat Ref No 675530 or equivalent in Schneider Zencalo or MK Blanze as approved.

S&F MCB dustribution board SPN.240 volts, 8 ways powder coated, CRCA steel sheet constructed as per IS 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, eath bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required.

S&F ceiling rose 6 map, 3 plates polycarbonate body complete. Make – Havells Reo / Anchor Penta PC / SSk as approved.

S&F MCB distribution board ETPN, 415 volts, 4 ways powder coated, CRCA steel sheet constructed as per IS : 8623, degree of protection IP 43 - IK 09 with metal door, recess mounted, having insulated 100 amp tinned copper bus bar, neutral busbar, earth bar, din bar, detachable gland plate, interconnection, earthing connection, blanking plates in unused spaces as required. Make : SIMENS/Ligrand/Schneider

M&L for submain wiring alongwith earth continuity conductor with PVC insulated FR multistraned copper conductor cable (Phase-Red, Neutral-Black, Earth-Green) drawing into and including concealed rigid non metallic PVC conduit, medium grade, ISI marked ivory colour along with accessories of following nominal sizes :-

(a) 2x4 sqmm + 1x2.5 sqmm earth continuity conductor in 20 mm dia conduit.

(b) 2x6 sqmm + 1x4 sqmm earth continuity conductor in 20 mm dia conduit.

S&F LED batten (1.2m) made of CRCA sheet housing with a PC glossy difusser duly prewired connection having a nominal system lumen output of 2000 lumes at a minimum system efficacy of 105 lumens per watt and total power consumption not more than 19 watt incl driver. It has a rated system life time of 40000 burning hours at L70 and should have a color temperature of 6500K, CRI>80, THD < 10% and PF > 0.95 complete. Make- Philips cat ref no. ENDURALED BATTEN “BN 108C led 20s PSU CDL WH” or equivalent in wipro or GE lighting as approved.

S&F LED bulkhead fitting 9 watt IP 66 & IK 09 with pressure diecast aluminium housing & polycarbonate diffuser duly prewired for connection with flexible multi stranded copper conductor cable as required all as per Philips cat ref no. WT202W LED6S CW PSU S1 PC or equivalent in Wipro or Havells as approved.

S&F LED bulkhead fitting 9 watt IP 66 & IK 09 with pressure diecast aluminium housing & polycarbonate diffuser duly prewired for connection with flexible multi stranded copper conductor cable as required all as per Philips cat ref no. WT202W LED6S CW PSU S1 PC or equivalent in Wipro or Havells as approved.

S&F LED 20 Walt street light made up to pressure dia cast housing with prismatic poly carbonate diffuser and indiviual LED's with secondry optics and IP 65 protection complete as specified and directed. Bajaj cat ref No. BCLST 20W LED code 169829 or equivalent in philips or Wipro as approved.

S&F S&F MCBs as per load requirement ‘A’series of breaking capacity 10 KA, ISI marked incl required wiring connection with copper lugs of suitable size provided in MCB DBs of following ratings:

a) Single pole 6 to 16 amp.

(b) Double pole 32 amp.

(c) Four pole 63 amp.

S&F galvanized pressed steel terminal boxes concealed in wall of thickness 1.20 mm covered with phenolic laminated white sheet cover 3 mm thick in renewal of wooden meter boards of size 250 mm x 300 mm x 60 mm deep for fixing energy meters complete.

S&F fully transparent meter box suitable for single phase energy meter made of polycarbonate / high grade engineering plastic to permit clear view of display and can be sealed in such a way that the entire meter is accessible only after breaking the seal complete.

Taking down carefully electric meters, any type upto 40 amps capacity after disconnecting and keep in safe custody and refixing inside transparent meter box complete. Note : Transperent meter box shall be measured and paid seperately.

Taking down MCB distribution boards with incoming and outgoing controls any make, any capacity after disconnecting complete.

Taking down carefully aluminium submain wiring with PVC surface conduit and making good disturbed surfaces complete.

Taking down Ceiling Fan of any make, type and sweep by disconnecting Electric Connection and keeping in safe castody for repair.

M&L for repair of ceiling fan any sweep of any make, cleaning throughly, servicing of fan motor & parts fitted there in, oiling, greasing to bush / bearings, replacement of unserviceable parts required, applying two coat of white synthetic enamel paint over one coat of primer on fan blades and body, re- assembling, testing hanging at site as directed.

M&L for pipe in pipe chemical earthing with GI pipe electrode 3.0 m long having outer pipe nominal dia 80 mm & inner pipe nominal dia 50 mm duly filled with highly conductive and anti corrosive compound of required quantity having chemical composition Bentonite 40%, copper sulphate 20%, Gypsom 5%, Graphite 10%, Alum 5%, Zinc sulphate 10%, Aluminium sulphate 10% burried in ground by digging a bore of 150 mm dia surrounded by soil friendly backfill compound non soluble in water including connection with GI strip 32x6 mm from pit to building making PCC pit of size 0.3 m x 0.3 m x 0.3 m (inner size) in mix 1:3:6 type C1 with RCC 1:2:4 type B-1, 40 mm thick cover reinforced with 8 mm dia MS bars 3 Nos both ways with lifting hook made out of 8 mm dia bar and testing on completion to achieve value not more than 1.0 ohm complete.

M/s Dhruv Epoxy Coat

ALBA AC AND REF SERVICES