Eloor Municipality Pathalam Communicty Hall - electrification Work

Amount

Electrification

Supply and wiring points according to IS 732-1989 using rigid PVC conduit of minimum size 20 mm with specials conforming to IS 9537 part III 1983 and with suitable size specials conforming to IS 3419-1988, fixing the conduit using metal saddles spacing not exceeding 50 cm or concealed suitably and with 1.00 sq mm PVC insulated stranded single core copper conductor cable 650V grade,including providing Switch Board main and continuous earthing with No. 14 SWG copper, required qty of copper earth socket, brass bolt and nut crimping/ soldering etc complete with suitable size modular type metal switch boxes, modular type front plates (white or off white) etc. up to and including 6 A modular type SP switches and making good the surface of wall, colour washing etc. complete. All the terminations in the switch boards and DB's shall be tinned and the wires shall be drawn and fixed along the periphery of the box using suitable ties, tie mounts etc as required. Single control light point with 6A, 3 plate ceiling rose

Twin control light point with 3plate ceiling rose

- Do - Single control light point without ceiling rose

- Do - Single control ceiling fan point without ceiling rose & with socket size stepped electronic regulator.

- Do -Call bell point with piano type 6 A bell push at one end and 6 A, 3 plate ceiling rose at other end

- Do - Combined plug point with 6 A, 5 pin plug socket controlled by 6 A switch in the same switch board as that of light points.

- Do- Independent plug

Supply, conveyance, installation, testing and commissioning of pre-wired light fitting made from 0.5mmCRCA sheet complete with all accessories and lamps etc. directly on wall using 2 nos. suitable 'C/U' brackets to suit the fitting and giving connections with required length of 16/0.20mm 3 core copper conductor flex wire conforming to relevant ISS or extending the original wiring and giving connection etc. as required. LED 20W LED light fittings

SITC Street light fitting with 70W LED Streetlight with Luminiare efficeincy >105 lm/W rugged aluminium alloy housing with all accessories complete (Wipro make 70 W 5700K, Lumen/watt >105 Cat. NoLR02 - 781 -xxx -57-G2 or equivalent ) on existing pipe and giving connection with 24/0.20mm 3 core flex wire as required..

SITC Street light fitting with 100W LED Street light with Luminiare efficeincy >105 lm/W rugged aluminium alloy housing with all accessories complete ( Wipro make 100 W 5700K, Lumen/watt >105 Cat. NoLR02 - 102 -xxx -57-G2 or equivalent ) on existing pipe and giving connection with 24/0.20mm 3 core flex wire as required..

Supply, conveyance, installation, testing and commissioning of pre-wiredrecessed type LED light fitting made fromCRCA powder coated sheet complete with all accessories and lamps etc. directly on ceiling or suitable frame work if necessory and giving connections with required length of 16/0.20mm 3 core copper conductor flex wire conforming to relevant ISS or extending the original wiring and giving connection etc. as required.18W LED recessed down light Square fitting Philips make Green LED Plus square DN 177B LED 15S-6500 PSU WH or equivalent make Wipro make Iris slim square LD81 -171-xxx - 60-xx .

- Do - 18W LED surface down light Square fitting Philips/Wipro make Iris slimsurface mounted square LD81 -171-xxx - 60-SM

- Do - 36/40W LED recessed Panel light Square fitting Wipro make Elate CRCO10 or equivalent make including suitable frame work if required for fixing false ceiling .

- Do - 4W LED recessed Foot light Square fitting Osram make OLUX or equivalent Philips make .

- Do - 5W LED Mirror lamp light fitting K- Lite make ID 1596 or equivalent make .

- Do - 5W LED Exit lamp with necessory inbuilt battery back up .

Supply, conveyance, installation, testing and commissioning of pre-wired light fitting Recessed mounted aluminium extruded Linear LED Luminair with superior anodised aluminium finish including suspension arrangments , 35 W, 3850 Lumen Luxpower Linear , 4 ft , warm light ,direct light emission, 100% downward direction THD less than 10% ,Luminiare efficeincy 100 - 115 lm/W Osram make LUXPOWER LINEAR 35W 830 L12 4x1 or equvalent make and giving connections.

Supply and fixing angle / straight brass lined skirt type, bakelite batten holder without shade and giving connection etc as required

Supply and providing the following types and power rated lamps in the existing fittings as required 9W LED Bulb in the existing fittings

Supply and installation of suitable size MS rod type fan clamp as per IS 732 as required.

Supply and providing every additional length of down rod of suitable size heavy gauge GI / WI pipe with 16/0.20mm PVC insulated and PVC sheathed 3 core round copper conductor flex wire conforming in relevant ISS or with original wiring extended including painting as required.

Supply, conveyance, installation, testing and commissioning of ceiling fans of the following sizes using standard accessories excluding resistance type regulator, wiring the down rod with 16/0.20mm PVC insulated and PVC sheathed 650/1100V grade 3 core round copper conductor flex wire or with extended original wiring etc. as required.1200 mm sweep (Category B) - 5 Star rated

Supply, conveyance, installation, testing and commissioning wall mounting fan of the following sizes using mounting brackets supplied along with the fan and giving connection with existing wire.450 mm sweep Oreint make Tornado or equivalent make.

Charges for cutting holes suitable for accommodating exhaust fans of sizes up to 305 mm sweep including plastering, colour washing etc. as required. Incuding suitable self operated louver and bird guard etc.

Charges for cutting holes suitable for accommodating exhaust fans of sizes exceeding 305 mm sweep up to 450 mm including plastering, colour washing etc. as required.Incuding suitable self operated louver and bird guard etc.

Supply, conveyance, installation, testing and commissioning of the following sizes of exhaust fans in the existing opening, fixing necessary bolt and nuts, making good the damages etc. as required including giving connections with required length of 24/0.20mm PVC insulated and PVC sheathed 3 core round copper conductor flex wire conforming to relevant ISS. 200 mm, single phase, light duty exhaust fan in plastic body

305 mm, single phase, heavy duty, 1400 rpm exhaust fan in metal frame

380 mm, single phase, heavy duty, 1400 rpm exhaust fan in metal frame

Supply and fixing the following types of superior quality 250V A.C call bell on existing M.S. box and giving connections with required length of 3 core, 16 / 0.20mm 650/1100V grade PVC insulated and PVC sheathed round copper conductor flex wire conforming to relevant ISS or with the extended original wiring, earthing the MS box and making good the surface as required.Call Bell.

-Do - Ding Dong bell

-Do - Buzer

Supplying and fixing the following sizes of M.S. Boxes made out of 1.60 mm thick sheet painted grey (both inside and outside ) in surface/ recess including phenolic laminated sheet covers of thicknesses noted along with screwed to the box as front cover with steel screws, cup washers etc. making good the surface, painting /colour washing etc. as required. 100 mm x 150 mm x 50mm with 3 mm sheet

Supply & Fixing the following types/ sizes of boxes suitable for modular accessories in surface/ recess including making good the damages, colour washing etc as required ( RoHS)3 module metal box in recess

-do - 2 module metal box in recess

-do - 4 module metal box in recess

-do - 8 module metal box in recess

-do - 12module metal box in recess

Supply & Fixing the following types/ sizes of front plates on the existing modular boxes. (RoHS)3 module white/ off-white

- do - 2 module white/ off-white

- do - 4 module white/ off-white

- do - 8 module white/ off-white

- do - 12module white/ off-white

Supply and Fixing the following modular switches & accessories in the existing front plates and giving necessary connections as required (Group B)6 A SP 1 way switch

-do - 16 A SP 1 way switch

- do - 6 A Universal socket

- do - 6 / 16 A combined socket

- do - 25 A socket

20 A DP switch with ind

-do - 16 A SP 1 way switch with ind

Supply and fixing the following sizes of PVC Conduit conforming to IS 9537 / 1983 part III along with all required accessories on surface including making good the damages etc as required.20 mm dia light gauge /equvalent PVC Caping and casing 25x12 or 25x16mm.

- do - 25 mm dia light gauge /equvalent PVC Caping and casing 32x12 or 32x16mm.

- do - 32mm dia light gauge /equvalent PVC Caping and casing 50x20 or 38x20 mm .

Supply and fixing the following sizes of PVC Conduit conforming to IS 9537 / 1983 part III along with all required accessories in recess including cutting the wall and making good the damages etc as required.20mm .

- do - 25 mm dia light gauge

Supply and drawing 650/1100 V grade PVC insulated stranded single core copper conductor cables conforming to IS 694 part I 1990 in the existing surface / recess conduit as required including giving necessary connections of the following sizes.1.50 sq mm 2run

1.50 sq mm 3 run

1.50 sq mm 4 run

1.50 sq mm 5 run

1.50 sq mm 6 run

2.50 sq mm 2 run

2.50 sq mm 4 run

2.50 sq mm 6 run

4.00 sq mm 2 run

4.00 sq mm 4 run

4.00 sq mm 6 run

Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of MCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCB/ isolator etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required 8 way (8+24) - double cover TPN vertical DB with provision for fixing MCCB as incomer and SP/ TP MCB as outgoing (IP 42/43)

- do - 6 way (8+18 - double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/ RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43)

4 way (8+12) - double cover TPN vertical DB with provision for fixing 4P MCB / Isolator/ RCCB/ RCBO as incomer and SP/ TP MCB as outgoing (IP 42/43)

6 way (8+18) - three phase double cover (IP 42/43)

4 way (8+12) - three phase double cover (IP 42/43)

-do - DP enclosure for independent mounting of MCB

-do- FP enclosure for independent mounting of MCB

Supply and installation of the following accessories suitable for 50 Hz AC supply conforming to IS 8828-1995/ IEC 60898 of the following current ratings in the existing enclosure and giving connections as required 63 A double pole mini break isolator

40 A four pole mini break isolator

40A, 4 pole, 30 mA RCCB

- do - 6 A to 32 A, 10 kA, SP MCB (C curve)

- do - 6 A to 25 A, 10 kA, TP MCB (C curve)

6 A to 25 A, 10 kA, 4 pole MCB (C curve)

6 A to 25 A, 10 kA, 2 pole MCB (C curve)

80A, 25/35 kA (Ics=100%Icu), 3 pole, current limiting type MCCB having thermal setting range of 80 - 100% with thermal magnetic release having adjustable OL

Supply and installation of sheet steel, phosphatised and painted, dust and vermin proof enclosure of LOAD BANK MCCB DB including copper /brass bus bar, neutral link, earth bus and DIN rail suitable for fixing MCCB as incomer and outgoings etc. fixed on wall using suitable anchor bolts or fixed in recess including cutting hole on the wall , making good the damages, colour washing etc. as required L& T make Brand Enersys-s SMDB- TN250 D ,O/G 100 A 8 way as per IEC: 61439-2 ,IP 43, short time withstand current 36 kA including metering extension box on top and cable entry box on bottom, Left side and Right side , 4 nos corner box and mounting base etc. complete including contrlol wiring .

Do - 160A, 35 kA (Ics=100%Icu), 3 pole, current limiting type MCCB having thermal setting range of 80 - 100% with thermal magnetic release having adjustable OL L& T make suitable for above Load Bank DB as DN1-250N 3 Pole MCCB

Do - 80A, 35/25 kA (Ics=100%Icu), 3 pole, current limiting type MCCB - do -

Do - 25A, 35/25 kA (Ics=100%Icu), 3 pole, current limiting type MCCB - do -

S&F earth fault modules for 125to 200A

S& F rotary Handle Kit for 160A MCCB

S& F spreader terminal for 160A MCCB

Do - internal Lightning /Surge protection Device OBO Bettermann Class B+ Class C + Type II Internal Lightning /Switching surge protection Device ( V25B +C/3 +NPE ) for three phase protection at Sub switch Board .

Three phase multifunction meters to read V, A and F, accuracy class 1

150/ 5 A, 5 VA, resin cast metering CT of accuracy class 0.5

150/ 5 A, 5 VA, 10 P 5, tape wound protection CBCT

LED indicators for all voltage ranges - Blue Colour

LED indicators for all voltage ranges - Red, Green, Black, Yellow or Orange Colour

Aluminium anodised Danger Notice Board of size 200 x 150 mm. with inscriptions ( both in English and Malayalam) and conventional Skull and Bone in Red colour.

Carrying out control wiring for panel with normal meters and indication lamps alone with 650/1100 V grade PVC insulated stranded single core copper conductor cables conforming to IS 694 part I 1990 as required.1.50 sq mm single run with required sockets.

Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using 1.60 mm CRCA sheet as per approved design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments should be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc. including control wiring

Supply and fixing the following types of beeding along the periphery of doors/ other detachable compartments to make the panel assembly dust & vermin proof including sticking with glue'A' section neoprene beeding suitable for 1.60/ 2.00 mm sheet

Supply and providing the following size of SMC sheets in the panel as barriers & shrouding using required bolts and nuts including cutting to shape etc., as required.3 mm thick

Fabrication, supply, conveyance and installation of base frame for floor mounting type panel board using channel of class designation ISMC 75 including cutting, welding, drilling holes, painting with two coats of synthetic enamel paint over a coat of zinc chromate primer, bolting the frame to the panel and to the finished floor using required bolt and nuts, making good the damages etc. as required.

Fabrication, supply & fixing main bus bar system and interconnections with electrolytic grade copper strips/ rigid conductors conforming to IS 1867 (with latest amendments) for bus bar arrangement with single strip per phase supported on finger type bus bar supports of adequate size, spacing between supports not exceeding 50 cm & overhang not exceeding 5 cm including bending to shape, drilling holes, tinning the points of contacts, fixing heat shrinkable PVC sleeves, plated bolts and nuts with plate washers and spring washers, copper sockets for round conductors, etc., as required.

Fabrication, supply & fixing earth bus system with copper strip/ conductor and connecting all accessories as per rule including g tinning the points of contacts etc as required

320 A, 70 kA (Ics=100%Icu), 3 pole, current limiting type MCCB with microprocessor based release with thermal setting of 50 - 100% having adjustable OL & SC

S&F earth fault modules for 250to 400A

S& F rotary Handle Kit for 320/160A MCCB

S& F spreader terminal for 320A /160A MCCB

Do - 160A, 35 kA (Ics=100%Icu), 3 pole, current limiting type MCCB having thermal setting range of 80 - 100% with thermal magnetic release having adjustable OL L& T make suitable for above Load Bank DB as DN1-250N 3 Pole MCCB

Do - internal Lightning /Surge protection Device OBO Bettermann Class B/ Type I Internal Lightning /Switching surge protection Device ( MCD 50 B OS -3 Nos, MCD 1125B /NPE - 1 No ) for three phase protection at Main switch Board .

Three phase multifunction meters to read V, A and F, accuracy class 1

100/ 5 A, 5 VA, resin cast metering CT of accuracy class 0.5

100/ 5 A, 5 VA, 10 P 5, tape wound protection CBCT

LED indicators for all voltage ranges - Blue Colour

LED indicators for all voltage ranges - Red, Green, Black, Yellow or Orange Colour

Aluminium anodised Danger Notice Board of size 200 x 150 mm. with inscriptions ( both in English and Malayalam) and conventional Skull and Bone in Red colour.

Carrying out control wiring for panel with normal meters and indication lamps alone with 650/1100 V grade PVC insulated stranded single core copper conductor cables conforming to IS 694 part I 1990 for interconnecting the control devices/ equipments including providing suitable size insulated sockets at the termination points or soldered properly, providing numbering ferrules for the proper identification of the wiring, keeping the wiring firm by suitable tie/ tie mounts/ PVC duct etc as required.1.50 sq mm single run with required sockets

2 A 10 kA, SP MCB (C curve)

Supply and providing plate earthing as per IS 3043 with 1200x1200x12 mm GI/CI earth plate, 50 mm GI watering pipe fixed to the earth plate with 25 x 3mm GI clamps, GI funnel with weld mesh, filling required quantity of charcoal including construction of inspection chamber with a bed concrete of 1:4:8 PCC using 40 mm broken stone (10 cm thick), brick work in cement mortar 1:6, plastering the surface of brick masonry and the exposed surface of PCC bed with cement mortar 1:4, 12 mm thick, (the finished inside dimension shall be 450 x 450 x 450 mm) but excluding test joint, earth continuity conductor to the plate, and covering at the top. (in ordinary soil)

Supply and providing the following sizes of cast iron gully trap with covering at the top of the inspection chamber of earth pit as required 450 x 450 x 10 mm cast iron gully trap with covering

Supply and providing test joint for the earthing system using 2 Nos of the following sizes of strips including cutting and bending to shape, drilling necessary holes and fixed to the watering pipe etc as required.2 x 32 x 3 mm tinned copper strip

Supply and providing earth lead from the test joint to the earth electrode using the following sizes of conductors/ strips including cutting, drilling necessary holes (in case of strip) and fixing firmly with plate test joint etc as required.32 x 3 mm copper strip tinned at the points of contacts

Supply and laying the following sizes of strips laid 0.60 m below ground level including excavating trench of suitable size and refilling etc. as required (in ordinary soil).25 x 3 mm copper strip tinned at the points of contacts

Supply and clamping the following sizes of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 x 3 mm GI flat duly painted or heavy duty GI spacer saddles, spacing of clamps not exceeding 1m, making good the damages, colour washing etc. as required 25 x 3 mm copper strip tinned at the points of contacts

Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required.2.00 mm copper conductor (14 SWG)

- do - 3.15mm copper conductor (10 SWG)

4.00 mm copper conductor (8 SWG)

supply of superior quality copper earth socket for the following sizes of earth conductor including crimping etc. as required.2.00 mm (14 SWG)

- do - 3.15mm (10SWG)

4.00 mm (8 SWG)

Supply and providing the following sizes of bolt and nut with washers on the existing MS box / earth bus etc. as required including drilling necessary holes as required . 12 x 3mm brass bolt & nut

do - 25 x 6mm brass bolt & nut

Supplying , threading , laying and jointing of the following sizes of 'B' class GI pipe with all required accessories in ground in the existing trench as protective covering to earth leads./UG cables 40mm dia

Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing GI/ DWC pipe as required.3.5 core 185 sq mm

- do - 2 core 6 sq mm

- do - 2 core 4sq mm

Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3.5c 185 sqmmwith fabricated GI clamps of suitable size

3.5c 120 sqmmwith fabricated GI clamps of suitable size

3.5c 95 sqmmwith fabricated GI clamps of suitable size

Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.3 1/2 core 50core sq mm with factory made clamp

4 core 16core sq mm with factory made clamp

- do - 4 core 10 sq mm with factory made clamp

- do - 4 core 6 sq mm with factory made clamp

- do - 2 core 6 sq mm with factory made clamp

- do - 2 core 4sq mm with factory made clamp

Supply & laying of DWC pipe in hard soil 0.75m below ground level including excavation175 / 147 mm or nearest size

50 / 38 mm or nearest size

Supplying , threading , laying and jointing of the following sizes of 'B' class GI pipe with all required accessories in ground in the existing trench as protective covering to earth leads.75mm dia.

Supplying siemens / tropodur type nickel plated single compression brass cable gland for PVC insulated and PVC sheathed armoured aluminium/ copper conductor cable 1.1 KV grade, and making end termination suitable for 2/ 3/ 3½/ 4 core cable of the following sizes as required.185 sq mm

- do - 120 sq mm

- do - 95 sq mm

- do - 50 sq mm

- do - 16 sq mm

- do - 10 sq mm

- do - 6 sq mm

- do - 4 sq mm

Supplying and providing earth clamps for siemens/ tropodur type cable glands of suitable length and other dimensions noted along with each size of glands for the following sizes of cables as required.4sqmm-16 sq mm with 12 mm wide x 1 mm thick clip

25 sq - 95sq mm with 20 mm wide x 1.20 mm thick clip

Supplying and providing earth clamps made out of copper strips of the following sizes including cutting and bending the flat exactly to the shape of the gland, drilling necessary holes for nut & bolt, tinning the points of contacts and giving connections to the main earthing system as required.20 x 3 mm for earthing glands of size 120 sq mm to 185 sq mm

Supply of superior quality aluminium tubular cable socket and making core termination of cables of the following sizes including crimping etc. as required.185 sq mm

- do - 120 sq mm

- do - 95 sq mm

- do - 70sq mm

- do - 50 sq mm

- do - 25sq mm

- do - 16 sq mm

- do - 10 sq mm

- do - 6 sq mm

- do - 4 sq mm

Supply of superior quality copper tubular cable socket and making core termination of cables of the following sizes including crimping etc. as required.2.50 sq mm

Painting letters or figures of the following sizes with enamel paint as identification mark to SB, DB, panel board etc as required 2.50 cm, 4 cm or 5 cm height

Fabrication, supply, conveyance and fixing frame work made out of suitable size angle iron/ flat cut and welded to shape of suitable size painted with 2 coats of synthetic enamel paint over a coat of red oxide primer & with drilled holes to mount the switch gear, fixed to wall using suitable size anchor bolts or grouted to wall, making good the damages, colour washing etc as required

Supplying and installation including all manner of supports/ suspenders, anchor bolts etc for cable trays made out of suitable size channel sections, slotted angles, flats, MS plates etc as required including painting with 2 coats of synthetic enamel paint over a coat of zinc chromate primer, making good the damages, colour washing etc as required.

Supply, fabrication, conveyance and fixing the following sizes of B class GI pipe bent to shape / cut and welded to shape and fixing the same to wall / parapet using clamps as noted along with each size, painting with 2 coats of synthetic enamel paint over a coat of zinc chromate primer, making good the damages, colour washing etc as required (for the installation of outdoor light fittings).32 mm dia with clamps made from 20 x 3 mm MS flat

Supply and fixing 45 w LED Gate Light fixture K-LITE make DISC ID No: 5382 or equivalent on existing pipe and giving connections

Supply and providing Hensel make 200x 160 x 98 mm Street light loop out Box (ID No: K 8250) with Wago/Connect well/Elmex 8way Terminal connector and 2A SP MCB suitable mounded on light poles as required including all charges

Supply, conveyance, installation, testing and commissioning of 3 HP Horizontal Openwell Submersible Motor pump set working voltage 3 phase, 415V, 50Hz , Ac Supply ,with head range up to 25 Mtr , delivery size 50 mm ( Kirlosker make Model KOS -325 + or equivalent make )etc. complete.

Supply and fixing Submersible pump controller starter suitable for 3 HP Open well submersible pumpset including overload protection, dry run protection and single phasing preventing protection etc. complete L&T or equivalent make

supply, threading, laying and jointing 50 mm 10 kg HD pipe with all accessories for delivey pipe

50mm or nearest size Hose Collar

50mm or nearest size CI flange set

50mm Full way wheel Valve

50mm or nearest size CI heavy duty non return valve

Supply and providing 12mm nylon rope

Supply and drawing PVC insulated & sheathed 650/1100 V grade 4.00 sq.mm 3 core copper conductor flat cable for submersible pump motor conforming to IS 694 part I 1990 as required including giving necessary connections of the following sizes.

Supply and clamping the following sizes of "B" class GI pipe on wall with all required accessories & clamps etc., including cutting and making good the walls, painting the exposed portions etc. 50mm B class with specials such as bend ,coupler , union etc.

Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) using 2.00 mm CRCA sheet as per approved design and requirement, for out door metering cubicle two partioned hinjed front door with glass panel for meter side , powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments should be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc.

3 phase, 4 wire, 220 V ( L-N), suitable for -/1 A CT or -/5A CT with RS 485 port of class 0.5. TOD Enegymeter L&T make model ER300 P class 0.50 Cat. No: WR300BC 12 Rs

100/ 5 A, 5 VA, resin cast metering CT of accuracy class 0.5

400 A, 415 V, DIN type fuse base.

250 A, DIN type fuse link

100 A, 415 V, 2 way neutral link mounted on DMC/ SMC base.

250 A, 415 V, 50 Hz, AC 23 A duty, TPN SDF for DIN fuse in sheet steel encosure

Supply and providing 2mm thick Elastomeric fire retardent insulating mat as per IS 15652/2006 to withstand 3.3 KV dielectric strength.

Supply and providing 5 Kg. Dry Chemical Powder type Fire Extinguisher with hose and clamps including fixing it to wall as required.

Supply and providing First Aid Chart duly framed and placed in a conspicuous location for clear vision.

Supply and providing 9 Litre capacity GI Fire Bucket painted in post office red with primer coat of red oxide and written with white paint 'FIRE' mounted on MS angle frame work/ wall bracket filled with fine sand, painting the bracket/ floor stand including making good the damages, colour washing etc. as required.

Supply of the following rated High wall split AC unit super quiet (Sound less than 40 db with capable of operation on long mode to make air flow upto 12m, cooling and dehumidification, 5 step vane controled swing operating on suitable R 22 refrigent with condensing and evapourating unit capable for cooling chordless remote control including lead wire etc. Daikin/Carrier/ Mitsubishi make 1.5TR High Wall Split type air-conditioner - 3 Star Inverter

Supply and fixing following voltage stabilizer V-Guard or equivalent with input voltage 170-270V and output 210-230V with over load protecion (cut off) time delay, indicator and chord wire etc. as required.4 KVA

Supply and providing frame for the outdoor unit

Installation and testing commissioning of the above AC unit

Supply and providing 22 guage soft drawn copper pipe 5/8 `` including rubber seal & foam sleeve and giving conection as required

Supply and providing 22 guage soft drawn copper pipe 3/8 `` including rubber seal & foam sleeve and giving conection as required

Supply and providing 25Mmm PVC Drain pipe in position as required

Supply and drawing multi core PVC insulated &PVC sheathed 650/1100 V grade copper conductor round flexible cables confirming to IS 694 part I 1960 in the existing surface/recess conduit as required including giving necessary connections of the following sizes3 core 4.00 sq.mm

Supply and fixing 100 x 50 mm PVC Cable Management System with base and lid along with the suitable accessories on surface and making good the damages in case of recessed installation as required for casing to the refrigerent pipe.

Supply, Installation,Testing and Commissioning of 82.50 KVA DG Set

Supply of 82.5 KVA Diesel Generator set, 3 phase, 415V, 50Hz, 0.80 pf, including AMF panel with integral acoustic enclosure as per CPCB norms and as per technical details given below icluding loading unloading and transporting etc. As per attached Detailed Specifcation

Installation charges of 82.50 KVA DG Set on the existing Cement Concrete foundation

SITC of Trickle charger unit suitable for 82.5 KVA DG Set and giving connections.

Supply and providing 100 mm / nearest size MS Pipe 5 mm thick ness ( Tata/jindal make ) complete with suitable size 12 mm thick flanges coupling with minimum 4/5 mtr length using suitable packing , MS bolt,nut and washersa and raising the same using chain pullies, necessory scafoldings, supporing with main building using necessory channel/angle in suitable size, etc. including painting with two coats of high temperature resistant aluminium paint etc. for extending the exhaust pipe of 82.50 KVA Diesel Generator set.

Earth work excavation in ordinary soil and depositing with a lead up to 50 m and lift up to 1.50 m including neat banking

cement Concrete 1:2:4 using 20mm Brocken stone for reinforced concreat work

Plain cement concrete 1:4:8 using 40mm ( Normal size ) broken stone. ( m3 )

Plastering with cement mortar 1:4, 12mm thick one coat.

Reinforcement for R.C.C works, bend tied and placed in position (plain grill requiring bend cold) using tor steel

Supply of HSD for Trail run

Supply & laying of one number PVC insulated and PVC sheathed armoured aluminium power cable of 1.1KV grade of the following sizes in the existing RCC/ HUME / STONE WARE/ GI/ DWC pipe as required.3 1/2 core 120 sq mm

- Do -2 core 4 sq mm

- Do -10core 2.50 sq mm Control cable

Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required. 3 1/2 core 120 sq mm

- Do - 2 core 4 sq mm

Supplying, laying and jointing of the following sizes of double wall corrugated (DWC) pipes made out of HDPE conforming to IS 14930 Part II for mechanical protection to underground power cables with all required accessories in ground in the existing trench 110 / 94 mm or nearest size

-do- 50 / 38 mm or nearest size

Supplying siemens / tropodur type nickel plated single compression brass cable gland for PVC insulated and PVC sheathed armoured aluminium/ copper conductor cable 1.1 KV grade, and making end termination suitable for 2/ 3/ 3½/ 4 core cable of the following sizes as required.4 sq mm

Supplying and providing earth clamps for siemens/ tropodur type cable glands of suitable length and other dimensions noted along with each size of glands for the following sizes of cables as required.4 sq mm to 16sq.mm with 12 mm wide x 1 mm thick clip

Supplying and providing earth clamps made out of copper strips of the following sizes including cutting and bending the flat exactly to the shape of the gland, drilling necessary holes for nut & bolt, tinning the points of contacts and giving connections to the main earthing system as required.20 x 3 mm for earthing glands of size 120 sq mm to 185 sq mm

Supply of superior quality Aluminium tubular cable socket and making core termination of cables of the following sizes including crimping etc. as required.4 sq mm

Supply and providing plate earthing as per IS 3043 with 600x600x6.30 mm GI/CI earth plate, 20 mm GI watering pipe fixed to the earth plate with 20 x 3 mm GI clamps, GI funnel with weld mesh, filling required quantity of charcoal including construction of inspection chamber with a bed concrete of 1:4:8 PCC using 40 mm broken stone (10 cm thick), brick work in cement mortar 1:6, plastering the surface of brick masonry and the exposed surface of PCC bed with cement mortar 1:4, 12 mm thick, (the finished inside dimension shall be 300 x 300 x 300 mm) but excluding test joint, earth continuity conductor to the plate, and covering at the top. (in ordinary soil)

Supply and providing the following sizes of cast iron gully trap with covering at the top of the inspection chamber of earth pit as required 300 x 300 x 6 mm cast iron gully trap with covering

2 x 25 x 3 mm tinned copper strip

Supply and providing earth lead from the test joint to the earth electrode using the following sizes of conductors/ strips including cutting, drilling necessary holes (in case of strip) and fixing firmly with plate test joint etc as required.32 x 3 mm copper strip tinned at the points of contacts

Supply and laying the following sizes of strips laid 0.60 m below ground level including excavating trench of suitable size and refilling etc. as required (in ordinary soil).25 x 3 mm copper strip tinned at the points of contacts

Supply and clamping the following sizes of strips on surface of wall/ parapet/ existing cable tray using clamps fabricated from 20 x 3 mm GI flat duly painted or heavy duty GI spacer saddles, spacing of clamps not exceeding 1m, making good the damages, colour washing etc. as required 25 x 3 mm copper strip tinned at the points of contacts

Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required.4.00 mm copper conductor (8 SWG)

supply of superior quality copper earth socket for the following sizes of earth conductor including crimping etc. as required.4.00 mm (8 SWG)

Supply and providing the following sizes of bolt and nut with washers on the existing MS box / earth bus etc. as required including drilling necessary holes as required . 25 x 6mm brass bolt & nut

Supply and clamping the following sizes of "B" class GI pipe on wall with all required accessories & clamps etc., including cutting and making good the walls, painting the exposed portions etc., as protective covering to earth leads / cables.32 mm dia

40 mm dia

Supply and providing 5 Kg. Dry Chemical Powder type Fire Extinguisher with hose and clamps including fixing it to wall as required.

Supply and providing 2mm thick Elastomeric fire retardent insulating mat as per IS 15652/2006 to withstand 3.3 KV dielectric strength.

Supply and providing 9 Litre capacity GI Fire Bucket painted in post office red with primer coat of red oxide and written with white paint 'FIRE' mounted on MS angle frame work/ wall bracket filled with fine sand, painting the bracket/ floor stand including making good the damages, colour washing etc. as required.

Supply and providing First Aid Chart duly framed and placed in a conspicuous location for clear vision.

Preparation of drawings including Schematic circuit diagram and necessory approval from the Electrical Inspectorate including all Fee etc.

SITC of Public Address System

Supply and fixing 32channel Digital Mixer, 7'' colour touchscreen Output processing -PEQ, Graphic EQ, Compressor , Delay , 31 Band Real Time Analysis and Spectrogram .Ahuja or equivalent make.

Line array Speakers - Self -powered Multi - functional FOH system ,70 Hz-19.50 Khz 110 degree x 7, 5 degree (average ) 133DB , 2 x 8'' LF/MF & 1x 4 '' '' Neo driver -1x3'' '' HF vice coil & Titanium diaphram ,Compatible Powersoft ,Ease Focus & Armonia Ahuja or equivalent make.

Fly bar with accessories for rigging speakers

Sub woofer Vented T-lined - Acive with power soft amp 2x 18 '' '' woofer & 3'' '' voice coil 2000 W RMS /4000W Peak Frequency range 40Hz -110 Hz. Ahuja or equivalent make.

Monitor speakers 12' 125 DBSPL 400W active Ahuja or equivalent make.

Shure BLX wireless mic with sm 58 head Ahuja or equivalent make.

Shure CVG 18 DS -BC -x podium mic Ahuja or equivalent make.

Shure wired mic PGA 58 Ahuja or equivalent make.

Mic stands 3 leg Ahuja or equivalent make.

Rack for mixer and mics

Servo stabiliser 10K

Two - way ceiling speaker with plastic back can 30w RMS 70V/100V/8Ohm ,Fire resistant plastic vented enclosure + metal grill Ahuja or equivalent make.

Class D compact amplifier 2x500W ,35 hz-20 Khz ( fixed 35 Hz 4 th Order Butterworth High pass Filter ),

Ceiling speaker 15W High Sensitivity 8'' Twin - Cone Driver Transformer for 100V or 16Ohm Applications Magnetic Grille for Seamless Aesthetics ( for lobby )Ahuja or equivalent make.

Mixer amplifier 130W ,4ohm/70V/100V 6input mixer ( for lobby )Ahuja or equivalent make.

Connection cable as per requirement and standard including suitable connectors

Supply and providing 20mm P.V.C Rigid Conduit.

Delstar a Grade Electrical contractors

Essjay Electrolinks (P) Ltd