Cwall SES MPZ

Amount

Demolishing stone rubble masonry manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge :

In cement mortar

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge..

In cement mortar

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level :

1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources)

Centering and shuttering including strutting, propping etc. and removal of form for :

Foundations, footings, bases of columns, etc. for mass concrete

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.

Thermo-Mechanically Treated bars of grade Fe-500D or more.

Random dry rubble masonry with hard stone (available at site) in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20mm nominal size) upto plinth level.

cement concrete block masonry with CC blocks having strength not less than 4n/mm2 in cement mortar 1:6 (1 cement: 6 coarse sand).

15 mm cement plaster on the rough side of single or half brick wall of mix :

1:6 (1 cement: 6 fine sand)

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface :

Water thinnable cement primer.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade :

Old work (Two or more coats applied @ 1.43 ltr/ 10 sqm) over existing cement paint surface.

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

One or more coats on old work.

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade :

One or more coats on old work.

Providing and fixing to existing door frames.

24 mm thick factory made PVC door shutters made of styles and rails of a uPVC hollow section of size 59x24 mm and wall thickness 2 mm (± 0.2 mm) with inbuilt edging on both sides. The styles and rails mitred and joint at the corners by means of M.S. galvanised/plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 20x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of ‘H’ section, a uPVC hollow section of size 100x24 mm and 2 mm (± 0.2 mm) wall thickness, fixed to the shutter styles by means of plastic/galvanised M.S. ‘U’ cleats. The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer’s specification and direction of Engineer-in-charge. (For W.C. and bathroom door shutter).

Providing and fixing P.V.C. low level flushing cistern with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete.

10 litre capacity - White

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Flexible pipe 32 mm dia

Providing and fixing PTMT bib cock of approved quality and colour.

15 mm nominal bore, 122 mm long. Weighing not less than 99 gms.

Providing and fixing PTMT stop cock of approved quality and colour.

15 mm nominal bore, 86 mm long. Weighing not less than 88 gms.

Providing and fixing PTMT pillar cock of approved quality and colour .

15mm nominal bore, 125 mm long foam flow. Weighing not less than 120 gms.

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.

15 mm nominal bore with 45 cm length.