Construction of Taluka Library At Sami, Patan, Gujarat. (2nd Attempt)

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Clearing and grubbing road land including uprooting rank vegetation grass

Rupees TwentyEight

bushes,shrubs,sapling and trees girth up to 300 mm removal of stumps of trees

1 0.35 28,455.09 Hec Thousand Four Hundred

cut earlier and disposal of unserviceable materials (C) By mechanical means in

FiftyFive Paise Nine Only

area of light jungle

Providing corrugated G.I. sheet of class-3 roofing fixed with glavanished iron J or L

Hooks, Bolts and nuts 8mm diameter with bitumen and G.I. limpet washer or G.I. Rupees Seven Hundred

2 222.34 limpet washer. filled with white lead complete excluding the cost of purlins, 734.19 Sqm ThirtyFour Paise Nineteen

Rafters and Trusses.(1) 0.80 mm thick sheet. Only

Excavation for foundation upto 1.5 m depth including sorting out and stacking of Rupees One Hundred

3 1709.02 useful materials and disposing off the excavated stuff upto 50 Meter lead. Soft 128.79 Cum TwentyEight Paise

soil SeventyNine Only

Excavation for foundation for depth from 1.5 m to 3.0 m including sorting out and Rupees One Hundred

4 434.09 stacking of useful materials and disposing off the excavated stuff upto 50 Meter 142.78 Cum FourtyTwo Paise

lead. Soft Soil SeventyEight Only

Filling available excavated earth (excluding rock) in trenches. plinth, sides of Rupees One Hundred

5 2034.92 foundations etc. In layers not exceeding 20 cm. in depth consolidating each 137.47 Cum ThirtySeven Paise

disposited layer by ramming and watering. FourtySeven Only

Filling in foundation and plinth with murrum or selected soil in layers of 20cm. Rupees Two Hundred

6 6552.33 thickness including watering, ramming and consolidating etc. complete. 273.86 Cum SeventyThree Paise

Filling in plinth with sand under floors including watering ramming, consolidating Rupees Four Hundred

7 58.70 and dressing complete 429.24 Cum TwentyNine Paise

TwentyFour Only

Applying general insecticide pest control treatment to floors, cupboards etc

including labour materials etc. complete. Using Imidacloprid 30.5 SCas Per IS

part -II( (0.075% concentration by mass) is recommended 10.5ml chemical diluted Rupees NinetyOne Paise

with 5 liters of water application 0.5 litre chemical /Sqm of surface is SixtyThree Only

recommended as per I.S.

P.C.C : Providing and laying cement concrete 1:2:4 (1-Cement : 2- Coarse sand : 4-

Rupees Three Thousand

graded stone aggregates 20 mm nominal size) and curing complete including cost

9 245.00 3,757.34 Cum Seven Hundred FiftySeven

of formwork in (A) Foundation and Plinth

Paise ThirtyFour Only

Providing and laying controlled cement concrete M.300 concrete With all lead,

including all transportation, pumping, pouring, curing of concrete etc complete

including the cost of formwork but excluding the cost of reinforcement for Rupees Five Thousand

reinforced concrete work in M300 all RCC element like foundation, NinetyThree Paise Ten Only

(A) Footing, at all floor level from below plinth and above plinth level

Providing and laying controlled cement concrete M.300 concrete With all lead,

including all transportation, pumping, pouring, curing of concrete etc complete

Rupees Six Thousand Nine

including the cost of formwork but excluding the cost of reinforcement for

11 244.83 6,944.08 Cum Hundred FourtyFour Paise

reinforced concrete work in M300 all RCC element like,

(B) Walls, from top of foundation level all floor level

Providing and laying controlled cement concrete M.250 concrete With all lead,

including all transportation, pumping, pouring, curing of concrete etc complete

Rupees Six Thousand Five

including the cost of formwork but excluding the cost of reinforcement for

12 131.97 6,532.55 Cum Hundred ThirtyTwo Paise

reinforced concrete work in M250 all RCC element lik, © Slabs, landing, shelves,

Balconies, Girders and Cantilever all floor level.

Providing and laying controlled cement concrete M.250 concrete With all lead,

including all transportation, pumping, pouring, curing of concrete etc complete

Rupees Six Thousand Two

including the cost of formwork but excluding the cost of reinforcement for

13 143.21 6,248.73 Cum Hundred FourtyEight Paise

reinforced concrete work in M250 all RCC element lik © Slabs, landing, shelves,

SeventyThree Only

Balconies, Lintels, Beams, Girders and Cantilever all floor level.

Providing and laying controlled cement concrete M.250 concrete With all lead,

including all transportation, pumping, pouring, curing of concrete etc complete

Rupees Seven Thousand

including the cost of formwork but excluding the cost of reinforcement for

14 61.71 7,321.02 Cum Three Hundred TwentyOne

reinforced concrete work in M250 all RCC element lik © Landing, Stair case,

Lintels, Copping, Beams, Girders, shelves,Balconies, and Cantilever all floor level.

Providing and laying controlled cement concrete M.300 concrete With all lead,

including all transportation, pumping, pouring, curing of concrete etc complete

Rupees Six Thousand

15 138.01 including the cost of formwork but excluding the cost of reinforcement for 6,049.02 Cum

FourtyNine Paise Two Only

reinforced concrete work in M300 all RCC element lik (D) Columns, Pillars posts

and struts, all floor level.

GRADE SLAB (M200) : Providing and laying controlled cement concrete M.200

Concrete with all lead, including all transportation, pumping, pouring, curing of Rupees Four Thousand Six

16 59.47 concrete etc complete including the cost of formwork but excluding the cost of 4,667.68 Cum Hundred SixtySeven Paise

reinforcement for reinforced concrete work in M200 Grade Slab SixtyEight Only

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

TRIMIX Road (M200) : Providing & Laying M200 grade controlled cement

concrete without fly ash trimix usinng P21 (water reducing concrete admixture

at 100 ml per bag of cement & recon 3 s fiber at 125 gm per bag of cement

including Cutting, Filling, Rolling, consolidating and Shuttering of C channel

required to maintain level, slope and thickness of the concrete road leveling of

placed concrete with surface vibrator and finishing with power floater & trowel Rupees Six Thousand One

17 166.77 light brooming the surface & including Construction joints to be formed at 6,120.42 Cum Hundred Twenty Paise

every 5 mt distance by grooving with mechanical saw within 48 hrs. FourtyTwo Only

Groove/sawed joints shall be made of 5 mm width and depth min (1/3 rd

depth of the pavement) as shown in the drawing and shall be filled with ready

to use PU sealant of UV gradecutting & filling of expansion joint as directed by

Engineer in charge

Providing and laying rubble soiling, in a compact manner, foudation, road,

footpath etc. using 200 to 230 mm. cut size stones, covering and levelling the

Rupees One Thousand

surface with a layer of murrum after filling the voids with smaller sized stones or

18 256.45 1,062.77 Cum SixtyTwo Paise

stone chips, including watering, ramming well and consolidating each layer, As

SeventySeven Only

per drawings and design supplied by architect and instruction given by E.I.C.

Providing CRS Bar (Corrosion Ressitance Steel Bars) Reinforcement confermed to

Rupees EightyOne Paise

19 144731.47 IS-1786 FE-500D for R.C.C. work including bending, binding and placing in position 81.45 Kg

FourtyFive Only

complete upto floor two level

Brick work using common burnt clay building bricks having crushing strength not

Rupees Three Thousand

less than 35 kg./Sq.Cm. in foundation and plinth, in Cement Mortar 1:6 (1-

20 62.67 3,708.98 Cum Seven Hundred Eight Paise

Cement : 6 -fine sand) (B) Conventional

NinetyEight Only

Masonry work with aerated light weight concrete Blocks of size 60cm x 20cm x

20cm size, having crushing strength @ 35 kg/sqcm Fixing with ready-mixed

mortar ('Fixoblock'of M/s Ultratech cement Ltd./Rapid Fix/Lion) having tensile

Rupees Five Thousand One

adhision strength >0.8 N/mm2 and compressive strength of >2N/mm2.The mortar

21 334.63 5,171.05 Cum Hundred SeventyOne Paise

is to be fixed in a thickness of 3mm to 5mm on the clean and leveled surface of

blockmasonry using proper trowel. For all floor and lead and lift For

superstructure.

Providing 10mm thick cement plaster in single coat on brick/concrete walls for Rupees One Hundred

22 1742.76 interior plastering upto floor two level and finished even and smooth in (ii) 128.09 Sqm TwentyEight Paise Nine

Cement mortar 1:4 (1-cement :4-sand)(For all floor) Only

Providing 20 mm thick double coat mala cement plaster on interior and external

brick / concrete work for plastering comprising of base coat of 12 mm thick

Rupees Two Hundred

cement plaster in cement mortar (1 Cement : 4 coarse sand) in rough finishing

23 2128.76 290.72 Sqm Ninety Paise SeventyTwo

and 8 mm thick top coat of cement mortar 1:2 (1 Cement : 2 Coarse sand)

finished with trovel including all level, scaffolding, curing, tools, tackles etc

complete. ( For all floor )

Providing 15mm thick cement plaster in single coat on Rough (Similar)side of

single or half brick walls for interior plastering upto floor two level and finished

Rupees One Hundred

even and smooth in (iii) Cement mortar 1:6 (1-cement:6-sand) interior plastering

24 1822.47 148.22 Sqm FourtyEight Paise

above floor two level for every additional storey height. all type of scaffolding

tools, tackles etc complete. (For all floor)

Providing and applying external finish of average 2 to 2.5mm thick acrylic polymer

based texture and pattern with standard tool and applicator as specified by

manufacturer on exterior surfaces at all heights including scaffolding to give even

shades including thoroughly brushing the surfaces free from mortar droping and

other foreign matter and sand paper smoothed etc. complete as per the

Rupees Three Hundred

25 2128.76 manufacture specifications and up to the satisfaction of Engineer in-charge/ 301.99 Sqm

One Paise NinetyNine Only

Architect. The rate includes making of grooves, pattas and finishing as directed by

Architect/ EIC. Paint shall be measured and paid in seperate tender item. (Item

should be executed by approved applicator only.)

Providing and fixing G.I. hexagonal chickenmesh of size 16 x24 of 22 gauge at

junction of concrete and brick work or between different materials after making

"V" grove between two different material surface and filled with rich cement

mortar and @ 100mm on each side of surfaces including necessary "U" nails / Rupees Two Hundred

26 356.52 screws / washers with cleats for fixing, overlaps, scaffolding at all floors / all levels 232.79 Sqm ThirtyTwo Paise

/ all heights / all shapes etc. complete as per drawing / specifications and SeventyNine Only

direction of Engineer-in-charge. For civil, plumbing, electrical & infrastructure

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Constructing Under Ground water tank with Providing and laying controlled

cement concrete M250 mix for R.C.C. work including reinforcement, boxing,

centering, vibrating, curing and mixed with approved water proofing cement

compound or "CEMWET" or "PIDICRETE LW" integral water proofing admixture as

water proofing agent to be mixed with 50 kgs. bags shall be as recommended by

the manufacture of the water proofing material, concrete work for top, bottom

slab & side pardi, column, beam for under ground water tank item incl. 300mm

Free Board and Necessary excavation & refilling the available earth, raft thickness

250mm & wall thickness 230mm ., Sunctipn Pit size 600mmX600mmX600mm

Rupees Thirteen Paise

27 75000.00 water proofing cement plaster 20mm thick Double Coat with smooth finishing & 13.44 Litre

FourtyFour Only

Glazes tile Dedo, vata 10cm X 10cm , 50mm thick cement concrete flooring

watering etc. Comp. to all face of tank. including locking arrengement outlet,

inlet, overflow and washout outlet pipe arrengement as necessary & C.I. Cover

0.60 x 0.45 weight not less then 35 kg with locking arrengment.C.I. steps etc.

comp as per structural detail drawing Including thermo Mechanically treated bars

(TMT BARS) Fe 500/500D as directed by Eng-in-charge.

Providing erecting and fixing double coated ISI water tank of required capacity

Rupees Three Paise

28 20000.00 each with all necessary fittings and connection etc. complete on terrace 3.95 Litre

NinetyFive Only

Providing and laying six courses water proofing treatment with bitumen felt over

roofs consisting of first, third and fifth course of blown bitumen 85/25 or 90/15

conforming to IS : 702 applied hot @ 1.45, 1.20 and 1.45 Kg per square metre of

area respectively, second and fourth courses of roofing felt type 3 grade I Rupees Six Hundred

29 511.41 conforming to IS : 1322 (Hessian based self finished bitumen felt) , sixth and final 681.75 Sqm EightyOne Paise

course of stone grit 6 mm and down size or pea sized gravel spread at 6 cubic SeventyFive Only

decimeter per sqm including preparation of surface but excluding grading,

Providing and laying broken chine mosaic flooring for terrace using 12 mm

to 20 mm broken pieces of glazed tiles to be laid over cement mortar 1:3 to

Rupees Seven Hundred

plain or slope and to be tempered to bring mortar creme out upto surface

30 511.41 779.70 Sqm SeventyNine Paise Seventy

using white cement including rounding off junctions and extending them upto

cm along the wall,clearing with water and oxalic acid etc. as directed.

Water proof plaster : Providing 15 mm thick water proof cement plaster in single

coat on brick/ block masonry or RCC wall, at all heights, finished even and smooth

in CM 1:3 (1 cement : 3 sand) including providing and mixing water proofing

Rupees One Hundred

materials of approved make in recommended proportions by manufacturer and as

31 10.00 197.27 Sqm NinetySeven Paise

directed by Engineer-in-charge and finishing the surface wired finish to receive

TwentySeven Only

the tiles/ smooth finish with a floating coat of neat cement slurry at 2.75 Kg/ sqm

etc. complete at floor

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm (average) base of

cement mortar 1:6 ( 1 cement: 6 coarse sand) on new surface or fixing on existing

Rupees One Thousand

flooring by adhesive material including dismentaling of existing flooring and

32 85.53 1,472.91 Sqm Four Hundred SeventyTwo

jointed with color cement slurry including finised with flush pointing & cleaning

Paise NinetyOne Only

the surface etc. complete for antiskit

Providing and laying white glazed tiles 6mm thick in skrting risers of steps and

Rupees One Thousand One

dedo on 10mm thick cement plaster 1:3 (1-cement : 3-coarse sand) and jointed

33 159.56 1,127.48 Sqm Hundred TwentySeven

Paise FourtyEight Only

white cement slurry

Providing and applying Tactile Polyurethane (PU) Flooring system of approved

shade and design over the existing finished surface, including surface preparation,

cleaning, grinding, and removal of dust, oil, or loose particles. The system shall

comprise application of primer coat, base coat, and tactile PU topcoat with anti-

Rupees Two Thousand

slip finish to form tactile indicators (warning and directional tiles) for visually

34 50.00 impaired persons, as per approved pattern and sample. Work includes all 2,787.60 Sqm

EightySeven Paise Sixty

necessary surface levelling, repairing of undulations, masking, layout marking, and

application using manufacturer’s recommended tools and techniques to achieve a

seamless, uniform, and durable tactile flooring.

Providing and laying polished Kota stone slab flooring over 20mm (Average) thick

base of cement mortar 1:6 (1-cement : 6-coarse sand) or L.M. 1.1.5 (1-Lime putty Rupees One Thousand

35 19.69 :1.5 - coarse sand) laid over and jointed with grey cement slurry mixed with 1,019.39 Sqm Nineteen Paise ThirtyNine

pigment to match the shade of slab including rubbing and polishing etc. complete. Only

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Providing and laying polished kota stone slab 25mm thick in risers of steps,skirting

Dedo and pillars laid on 10mm thick cement mortar 1:3 (1- Cement : 3 coarse Rupees One Thousand One

36 2.48 sand) and jointed with gray cement slury mixed with pigment to match the shade 1,184.64 Sqm Hundred EightyFour Paise

of slab including rubbing and polishing etc. complete. SixtyFour Only

Providing and laying Granite slab (16 to 18 mm thick) one side polished flooring

Rupees Two Thousand

over 20 mm (average) base of cement mortar 1:6 ( 1 cement : 6 coarse sand) or

37 459.64 2,354.13 Sqm Three Hundred FiftyFour

L.M. 1:1.5 laid and jointed with grey cement slurry including rubbing & polishing

Paise Thirteen Only

complete, for all floors.

Providing and laying 16 to18 mm thick polished Granite stone slab machine cut

in single piece in risers of steps, dedo, pillar, sill and jambs or dedo laid on

mm thick cement mortar 1 : 3 ( 1 cement : 3 coarse sand ) laid over and

jointed withgrey cement slurry incl. rubbing and polishing etc complete. The Rupees Two Thousand Five

38 386.20 rate includes lodding, unlodding, scaffolding, wastage, making hole, cutting/ 2,519.38 Sqm Hundred Nineteen Paise

chasing, rounding champhering, edge polishing of edges. The work shall be carried ThirtyEight Only

out as per the approval of architect and engineer-in-charge. for all floors

GRANITE SHELF : (500 D) : Providing, making, fixing as per detail drawing and

required length and depth shelf made from 18 mm Granite (1-Cement: 4- fine

sand ) with one side finish polished, round edge and providing lighting

arrangement cutout and fixing as per detail drawing and instruction of EIC.Rate Rupees Two Thousand One

39 0.75 shall inclusive all necessary hardware and fitting.The work shall be done as per 2,104.44 Sqm Hundred Four Paise

the specifications, sample approved and as directed by the Architect and FourtyFour Only

Engineer-in-charge.Rate shall inclusive of providing mock up sample for approval

Wooden Shelf : Providing, making, fixing as per detail drawing made from 19 mm

IS 710 BWP ply structure aand both side 1 mm thick laminate finish shall be of

approved make & shade and as per the detail drawing. All the edges of ply shall

be covered with 1 mm thick laminate finish Rate shall also inclusive of all

necessary,The rate shall be inclusive of shelf both side 1 mm thick laminatefinish

and as per detail drawer unit for Wooden Shelf as per selction by architect The

rate shall be in sqm of elevation area for all floors and at all heights including all

costs complete as per the Architectural drawings & instructions.Only the elevation Rupees Six Thousand

40 11.77 area of the storage unit will be measured and paid for. Item for 1 mm thick 6,037.36 Sqm ThirtySeven Paise ThirtySix

laminate fixing and polishing is included in this item. The work shall be measured Only

& paid in sqm The rates shall be inclusive of all wastages, material, labor, taxes,

transportation, loading, unloading, fixing in position, etc. complete to the

satisfaction of the Architect and EIC. The mock-up of 1 unit shall be approved

from EIC and Architecture prior to the final production.

Providing and fixing pre-cast Rubber Dye / steel Dye inter locking concrete block

60mm thick with grade of concrete M300 pnumatic compressed / vibrated

mechanically and as per approved design Confirming to IS 15658 : 2006 including Rupees Seven Hundred

35 mm Sand layer for levelling and filling the joint with sand in proper line and Paise SeventyFour Only

level as per guidlines of IRC : SP 63-2018 etc. Complete.

Kerb Stone : Providing and fixing pre-cast concrete kerb stone of gray cement

based concrete block 30cm length,30cm height and 15cm thick of M250 grade Rupees Three Hundred

42 280.43 concret as per approved design and including excavation for fixing in proper line 374.92 Rmt SeventyFour Paise

and level,filling the joint with C:M 1:3 (1cement:3fine sand) etc complete. NinetyTwo Only

Urinal partition : Providing & laying 16 to 18 mm thick both side mirror polished

granite of approved shade and quality, seleted and sorted for uniform color for

urinal partition/ division plate as per design and in required sizes and shapes after

chasing /cutting of dado with cutter machine fixing shall be carried out in white

cement sand mortar (1:1) with matching pigment and/ or necessary adhesive. Rupees Two Thousand Six

43 1.50 (Only finished granite work shall be measured). All expose edges shall be 2,624.36 Sqm Hundred TwentyFour Paise

champhered and polished. The rate includes making hole, cutting/ chasing, ThirtySix Only

rounding champhering, edge polishing of edges. The work shall be carried out as

per the approval of architect and engineer-in-charge.

Basin Counter/Granite Platform (All Floor : Width - 600 mm ) : Providing and

constructing approved shade and sample of Mirror finish granite platform

600mm width 25 mm thick Machine polished kotah stone as vertical supports at

sides,including cutting granite & kotah as per required shape , dedo 1'6" ht & size Rupees Five Thousand Two

44 7.56 to fit kitchen sink, moulding, tiles adhesive nosing, chamfered front edges, fixing, 5,268.29 Sqm Hundred SixtyEight Paise

disposal of debris etc complete with all labour and materials and as per detailed TwentyNine Only

drawings / architects instruction and approval by Engineer-in-charge. The

sample mock shall be approved from EIC.

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Granite Cladding : Providing & laying in line and level minimum 18 mm thick

(selected and sorted for its uniform colour and thickness) Granite cladding of

approved shade and quality on internal wired finished or mala finished

plastered surfaces as per drawing , size of the stone shall be 1.20 meter x

meter. Granite shall be fixed with cement based, highly polymer modified, and

high strength, flexible tile adhesive "Diamond Star" of BAL Endura Make or

equivalent of approved colour of thickness as specified by manufacturer. Rate

shall be inclusive of filling the grooves of minimum 10 mm wide x 10 mm deep

on both sides shall be filled with approved colour & make neutral cure glazed &

metal silicon sealant . The rate shall also include for necessary mortar base , tools

Rupees Two Thousand

, tackles , etc . including cleaning, polishing, and scaffolding etc complete at all

45 12.36 2,297.37 Sqm Two Hundred NinetySeven

heights, all places, and all shapes as per drawings and including laying in desired

Paise ThirtySeven Only

design and pattern and as per drawing or as directed by the EIC/Architect. Based

on available size of stones within the maximum size stated above will be

considered for final stone cladding pattern. Cladding shall be done only after

allowing the walls to wet out for a minimum exposure period of 6 weeks prior to

rendering/plastering/tiling. Rate to be inclusive of all material, wastage, necessary

tools tackles etc for fixing at all heights and for all floors. Clear laid area shall be

measured & paid in sqm.

Gypsum Ceiling : Providing and fixing single layer water proof gypsum board

mm thick sections using water proof board of size 1220 mm x 1830 mm x 8.0 mm

suspended by GI suspender channel of size 25 mm x 3 mm with intermediate

channel og size 18 mm x 40 mm x 0.8 mm at 1220 mm center to center ceiling

section of size 40 mm x 35 mm x 0.55 mm at 457 mm c/c and perimeter channel Rupees Six Hundred Six

A of size 20 mm x 27 mm x 30 mm x 0.5 mm at edges & drops incl.paper tap sand Paise NinetyFive Only

sofit cleat, anchor fastener, scoch bolt connecting cleat,joining compound top

coat on ceiling incl. making necy. opening for light fitting,diffuser etc. comp. as

per detail drawing as directed.

False ceiling : Providing and fixing eco-friendly light weight calcium silicate false

ceiling tiles having Tegular edge & 15 mm Thick Densified edges on the Tile

Periphery for Extra Strength The Light weight calcium silicate ceiling tiles shall

have , light reflection 85% non-combustible as per B.S. 476 part IV, 100%

humidity resistance and also having thermal conductivity0.043° w/m KC.for the

best thermal Insulation . The Light weight calcium Silicate tile shall be of approved

texture Fine fissured/Spintone/Cosmos having NRC value of 0.5 & Globe having

NRC value of 0.75 NRC or equivalent of size 595 X 595 mm to be laid on true

horizontal level suspended inter locking metal grid of hot dipped galvanized steel

sections (galvanizing @120 grams per sqm including both side) consisting of main

‘T’ runner suitably spaced at joints to get required length and size of 24X38mm

made from 0.30 mm thick (minimum) sheet, 1200mm centre to centre, and cross

‘T’ of size 24X28mm made out of 0.33mm (Minimum) sheet spaced 1200mm Rupees One Thousand Six

47 66.79 along spaced between main ‘T’ at 600mm centre to centre to form agrid of 1,674.15 Sqm Hundred SeventyFour Paise

1200X600mm and secondary cross ’T’ of length 600mm and size 24x28mm made Fifteen Only

of 0.30 mm thick (Minimum) sheet to be interlocked at middle of the

1200X600mm panel to form grid of size 600X600mm resting on periphery

walls/partitions on a perimeter wall angle pre-coated steel of size

(24X24X3000mm made of 0.40mm thick (minimum) sheet with the help of rawl

plugs at 450mm centre to centre with 25mm long dry wall screws @ 230mm

interval and laying 15mm thick Densified edges light weight calcium silicate

ceiling tiles of approved texture (Fine Fissured/Cosmos/Spintone) in the grid

including, cutting /making opening for services like diffusers, grills, light fittings,

fixtures, smoke detectors etc.,

wherever required, Main ‘T’ runners to be suspended from ceiling using G.I.

slotted cleats of size 25X35X1.6mm fixed to ceiling with 12.5mm dia and 50mm

long dash fasteners, 4mm G.I. adjustable rods with galvanized steel level clips of

size 85X30X0.8mm, spaced at 1200mm centre to centre long main ‘T’ bottom

exposed with 24mm of all T-sections shall be prepainted with polyester baked

paint, for all heights, as per specifications, drawings and as directed by engineer-

in-charge.Note:- Only calcium silicate false ceiling area will be measured from

wall to wall. No deduction shall be made for exposed frames/opening (cut outs) - -

having area less than 0.30 sqm. The calcium silicate ceiling tiles shall have NRC.

Value of 0.50 (Minimum) for Fine fissured/Spintone/Cosmos and 0.75 NRC for

Globe, light reflection 85% noncombustible as per B.S. 476 part IV, 100% humidity

resistance and also having thermal conductivity. 0.043° w/m KC.for the best

thermal Insulation

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

PLY WALL PANELING FINISH WITH PU FINISH : Providing & fixing 12mm thick IS

710 MR Grade ply fixed on frame work. The framework shall be fixed as per

drawing vertically & @ 600 mm c/c vertical & 1200 mm c/c horizontally. The

frame work shall be made from Ply make conforming to IS specification In

paneling, (intermediate, perimeter ) & (at vertical or horizontal joint of ply & at

turning point ) shall be fixed to the wall/floor & ceiling with Sheet metal

screws/Nylon grip screws of Corro-shield /Fischer, etc and shall be supported by

filling required size wedges /washers/ MS wall connectors or packings of teak Rupees Three Thousand

48 31.78 wood /MS washers to ensure right angles and plumb level. All ply/wooden 3,502.57 Sqm Five Hundred Two Paise

frameworks shall be treated with anti-termite treatment & hidden The frame FiftySeven Only

work shall be covered with approved make plywood(IS 710- 12 mm ply),adhesive

,tape, headless nails etc ,finished with MDF ( MDF base ply) with semiglossy PU

Paint & in pattern as shown in the drawing. Rate shall be inclusiveg grooves,

Hardware, fitting, fixture, scaffolding, adhesives, etc complete as per drawing or

as directed by EIC.

Flush Door With WPC frame (37 MM) : Providing and fixing in position 35mm

thick solid core wooden flush doors of approved make having fire retardant ply

facing on both sides and finished with 1 mm thick laminate as approved , WPC

Rupees Six Thousand Five

frame size - 125 X 63 MM Well Quality Hardware system of Hinges , Boxer

49 32.37 6,570.17 Sqm Hundred Seventy Paise

type door closer , Door handle , Euro profile , lock ,Door stop . work complete

including all type of hardware, fittings , fixtures etc complete as per detailed

drawings and specifications, sample mock shall be approved from EIC.

Flush Door with frame and finish with 1mm thick Laminate (37MM): Providing

and fixing in position 35 mm thick solid core wooden flush doors of approved

make having fire retardant ply facing on both sides and finished with 1mm thick

laminate as approved ,Indian Teak Wood Frame size - 125 X 75 MM, Single rebet , Rupees Four Thousand

50 46.33 Well Quality Hardware system of Hinges , Boxer type door closer , Door handle , 4,750.42 Sqm Seven Hundred Fifty Paise

Euro profile , lock ,Door stop . work complete including all type of hardware, FourtyTwo Only

fittings , fixtures etc complete as per detailed drawings and specifications, sample

mock shall be approved from EIC.

Double Leaf Flush Door with frame and finish with 1mm thick Laminate (37MM):

Providing and fixing in position 35 mm thick solid core wooden flush doors of

approved make having fire retardant ply facing on both sides and finished with

1mm thick laminate as approved ,Indian Teak Wood frame size - 250 X 75 MM Rupees Four Thousand

51 11.70 double rebet , Well Quality Hardware system of Hinges , Boxer type door closer , 4,899.17 Sqm Eight Hundred NinetyNine

Door handle , Euro profile , lock ,Door stop . work complete including all type of Paise Seventeen Only

hardware, fittings , fixtures etc complete as per detailed drawings and

specifications, sample mock shall be approved from EIC.

Providing and fixing factory made upvc fenesta wooden colour sliding glazed

window with Mosquito net and Approved sample by Architect/Client/EIC. all

height dimension comprising of upvc multi chambered frame with in built roller

track and sash extruded profiles duly reinforced with 1.60 + 0.2 mm thick

galvanizd mild steel section made from roll forming process of required lenght (

shape & size according to upvc profile ), appropriate dimension of upvc extruded

glazing beads and upvc extruded interlocks, epdm gasket,wool pile,zinc alloy

(white powder coated) touch locks with hook,zinc alloy body with single nylon

rollers (weight bearing capacity to be 40 kg),g.i. fasteners 100 x 8 mm size for

fixing frame to finished wall and necessary stainless steel screws etc. profile of

Rupees Twelve Thousand

52 125.73 frame & sash shall be mitred cut and fusion welded at all corners,including drilling 12,004.10 Sqm

Four Paise Ten Only

of holes for fixing hardware's and drainage of water etc. after fixing frame the

gap between frame and adjacent finished wall shall be filled with weather proof

silicon sealant over backer rod of required size and of approved quality,all

complete as per approved drawing & direction of engineer-in-charg. Three track

Three panels sliding window of 5 mm thick toughen glass and series 2000 frame

65 x 58 mm & sash 45 x 90 mm both having wall thickness of 1.9+ 0.2 mm and

single glazing bead of appropriate dimension.

Providing and fixing S.S. bird net jali (Invisible Grill)- using wire gauge with

average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all

complete With Aluminium equal angle frame or 12 mm mild steel U beading work

at required opening and at any height with all labour & material etc. complete. Rupees One Thousand

53 125.73 and fitting with necessary nuts, bolts, machine screws etc fixing i/c fixing with 1,303.60 Sqm Three Hundred Three Paise

necessory accessories and dash / Anchor fasteners of required size. on the top of Sixty Only

floors, concretes, wood, walls, sides of slab with suitable arrangements. etc

complete for all floors and at all levels

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Providing and fixing standared extruded of alluminium section of size 63mm x

38.10mm x 1.2mm (Jindal Section:2434, @ Wt. 0.643 Kg/mt) with colour Powder

Rupees One Thousand One

Coated alluminium frame for ventilation with 5mm thick frosted glass as details

54 3.96 1,175.56 Sqm Hundred SeventyFive Paise

etc complete for Ventilation. All Level

Providing and fixing M.S. grills of required pattern to wooden frames of windows

Rupees One Hundred

etc. with M.S. flats at required spacings and frame alround, square or round bars

55 1500.51 114.44 Kg Fourteen Paise FourtyFour

with round headed bolts and nuts or by screws (A) Plain Grill.

Wall Punning : Providing and applying Plasto XP Gypsum plaster ( USG Boral) or

equivalent make , minimum 12 mm thick in Wall and minimum 6 mm thick in

ceiling , including all labors, tools, tackles, scaffolding, surface preparation, mixing

of material, transportation (lead & lift) applying in position, Levelling, finishing,

Rupees Three Hundred

cleaning etc. complete to satisfaction of Employer's representative/ Employer.

56 50.00 365.62 Sqm SixtyFive Paise SixtyTwo

The rate also include making of grooves above skirting, Dedo tiles and around

window and door jambs etc. (cost of Bonding agent to the ceiling or RCC surfaces

is to be included in the item).item shall be used as per instruction of EIC.

Applying two coats of putty & two coats of primer of approved brand and

manufacture on new wall surface to give an even shade including thoroughly Rupees Fourty Paise

brushing the surface free from mortar dropping and other foreign matter and FiftyNine Only

sand papered smooth.

Wall painting (two coats) with plastic emulsion paint of approved brand and

manufacture on undecorated wall surface to give an even shade including Rupees EightyEight Paise

throughly brushing the surface free from mortar droppings and other foreign ThirtyNine Only

matter and sand papered smooth.

Finishing wall with weather proof exterior emulsion paint on wall surface (two

Rupees One Hundred

coats) to give an required shape even shade after thoroughly brushing the surface

59 2128.76 122.14 Sqm TwentyTwo Paise Fourteen

to remove all dirt, and remains of loose powdered materials. etc complete

Applying priming coat over new steel and other metel surface after and including

preparing the surface by throughly cleaning, oil, grease, dirt and other foreign

Rupees ThirtyEight Paise

60 108.98 matter and scoured with brushes fine steel wood, scrapers and sand paper with 38.15 Sqm

ready mixed priming paint brushing red lead.

Painting two coats (excluding priming coat) on new steel and other metal surface

with enamel Paint, brushing, interior to give an even shade including cleaning the Rupees NinetySix Paise

surface an even shade including cleanicn the surface of all dirt, dust and other FiftyNine Only

foreign matter.

Steel work, welded in built up sections framed work including cutting, hoisting,

fixing in position and applying a priming coat of red lead paint. (A)In beams and Rupees Nine Thousand

62 139.35 joists, channels angles Tees, flats, with connecting plates or angle cleats as in 9,108.48 Qui. One Hundred Eight Paise

main and cross beams. Hip and jack rafters, purlins conneted to common rafters FourtyEight Only

Providing in position PVC pipe sleeves of 6Kg/cm2 and length as per design for

following diameters for services wherever pipes pass through walls/ slabs/ beam

in mtrs length. All pipes shall be accurately cut to the required sizes, laid as per

drawing, kept in the position while concreting, and burrs removed before laying.

Rupees One Hundred

63 15.00 Open ends of the pipe shall be closed as the pipe is installed to avoid clogging 116.15 Rmt

Sixteen Paise Fifteen Only

while concreting. Rate shall be inclusive of removal of sleeves before water

proofing or grouting. For all floors / all levels / all heights. (a) 50mm Diameter

Providing in position PVC pipe sleeves of 6Kg/cm2 and length as per design for

following diameters for services wherever pipes pass through walls/ slabs/ beam

in mtrs length. All pipes shall be accurately cut to the required sizes, laid as per

drawing, kept in the position while concreting, and burrs removed before laying. Rupees One Hundred

64 15.00 Open ends of the pipe shall be closed as the pipe is installed to avoid clogging 185.84 Rmt EightyFive Paise EightyFour

while concreting. Rate shall be inclusive of removal of sleeves before water Only

proofing or grouting. For all floors / all levels / all heights. (a) 75mm Diameter

Providing in position PVC pipe sleeves of 6Kg/cm2 and length as per design for

following diameters for services wherever pipes pass through walls/ slabs/ beam

in mtrs length. All pipes shall be accurately cut to the required sizes, laid as per

drawing, kept in the position while concreting, and burrs removed before laying. Rupees Three Hundred

65 15.00 Open ends of the pipe shall be closed as the pipe is installed to avoid clogging 319.41 Rmt Nineteen Paise FourtyOne

while concreting. Rate shall be inclusive of removal of sleeves before water Only

proofing or grouting. For all floors / all levels / all heights. (a) 110mm Diameter

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Providing in position PVC pipe sleeves of 6Kg/cm2 and length as per design for

following diameters for services wherever pipes pass through walls/ slabs/ beam

in mtrs length. All pipes shall be accurately cut to the required sizes, laid as per

drawing, kept in the position while concreting, and burrs removed before laying. Rupees Four Hundred

66 15.00 Open ends of the pipe shall be closed as the pipe is installed to avoid clogging 499.45 Rmt NinetyNine Paise

while concreting. Rate shall be inclusive of removal of sleeves before water FourtyFive Only

proofing or grouting. For all floors / all levels / all heights. (a) 160mm Diameter

Core cutting : Providing and wet drilling accurate and clean holes of specified

diameter in RCC walls, slabs, beam or any other RCC member without vibration

by core cutting (diamond drilling) machine including scafolding, safety majors,

disposing the debris, cleaning for all levels/ all height as per structural

Rupees One Thousand One

consultant's drawing, after approval of engineer in charge etc compete. Rate shall

67 10.00 1,126.66 Nos Hundred TwentySix Paise

be inclusive of filling the hole with non shrink grout/Chemical Anchoring in good

manner. Measurement shall be taken for the depth of holes in running meter for

specified diameter. Holes shall made by authorised approved agency. (a) holes

Core cutting : Providing and wet drilling accurate and clean holes of specified

diameter in RCC walls, slabs, beam or any other RCC member without vibration

by core cutting (diamond drilling) machine including scafolding, safety majors,

disposing the debris, cleaning for all levels/ all height as per structural

Rupees One Thousand

consultant's drawing, after approval of engineer in charge etc compete. Rate shall

68 20.00 1,463.49 Nos Four Hundred SixtyThree

be inclusive of filling the hole with non shrink grout//Chemical Anchoring in good

Paise FourtyNine Only

manner. Measurement shall be taken for the depth of holes in running meter for

specified diameter. Holes shall made by authorised approved agency. (b) holes

SS RAILING : Providing & Fixing Stainless steel 304 grade pipe railing Horizontal

mm dia. 2 Nos. and Supprt pipe from wall 16mm Dia. at everymax 0.90mtr C/C

including welding, grinding, buffing, polishing and making curvature (wherever

required) and fitting the same with necessary stainless steel nuts, Plates and bolts Rupees Two Thousand

69 40.26 complete, i/c fixing the railing with necessary accessories & stainless steel dash 2,872.66 Rmt Eight Hundred SeventyTwo

fasteners, stainless steel bolts etc., fixed on Concrete or brick work . Rate Paise SixtySix Only

including of all materials.labour, fixing & polishing etc. comp. as per Drawing and

Approve by Engineer In Charge

SS RAILING : Providing and fixing stainless steel (Grade 304) railing Horizontal top

pipe of 50mm dia., verticle Sq pipe 32X32 mm 900 mm c/c and 16 mm Dia.

Nos. Horizontal Pipe equval Spacing Hollow Pipes, channels, plates etc., including

welding, grinding, buffing, polishing and making curvature (wherever required)

and fitting the same with necessary stainless steel nuts, Plates and bolts

complete, i/c fixing the railing with necessary accessories & stainless steel dash Rupees Three Thousand

70 76.65 fasteners, stainless steel bolts etc., of required size, on the top of the floor or the 3,764.88 Rmt Seven Hundred SixtyFour

side of waist slab with suitable arrangement as per approval of Engineer-in Paise EightyEight Only

charge, (for payment purpose only weight of stainless steel members shall be

considered including fixing accessories such as nuts, bolts, fasteners etc.). as per

Drawing and Approve by Engineer In Charge

Roller Blinds : Providing and fixing of approved quality roller blinds using phifer or

equivalent fabric of premium grade, with roller tube, bottom bar leveller made

of extruded aluminium alloy an Idler, Insert Type- Brackets, PVC chain etc. all

complete at all floor and heights as per approved specification. Roller Tube

Control, Clutch, Idler Side by side or single Roller Tube of extruded Aluminium

38mm inner dia - 41mm outer dia minimum wall thickness of 1.6mm. Roller blind -

roller blind fabric should be made up of 35% FibreGlass, 65% PVC, it should have

specific low emissivity treatment and lead free with Greenguard gold certification. Rupees One Thousand

71 121.68 It should have 3% to 5% openness, fabric thickness should be 0.43 mm, mesh 1,724.69 Sqm Seven Hundred TwentyFour

weight approx 400 gms/ sqmtr. It should cut UV rays, with antimicrobial Paise SixtyNine Only

properties preferably with Microban. The fabirc should be Flame retardant and

Lead Free. It should be GreenGuard certified with Gold Standard for low chemical

emissions for indoor use. including all accessories, material, labour,installation

etc..and complete the work satisfactorily as per instruction of architect or

Engineer-in charge.

White washing with lime on wall surface (three coats) to give an even shade incl.

thoroughly brooming the surface to remove all dirt, dust, mortar drops and extra Rupees Nineteen Paise

subsequent coat of white washing with lime on wall surface. FourtyThree Only

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Soft Board : Providing and fixing on wall 12mm thick approved quality soft board

with cotton cloth/fabric of approved make and shade on 12mm thick IS 710 MR

Grade ply with 19mm x 25 mm thick Ghana teak wood beading all around

including semi glossy PU polish, as approved sample and as directed by Architect. Rupees Two Thousand

73 10.20 The work shall be measured & paid in Sqm. for all floors, all level and at all 2,710.01 Sqm Seven Hundred Ten Paise

heights including all costs, The rate shall be inclusive of lacquer polish to all the One Only

exposed wooden members. Only the clear elevation area of the cloth/fabric shall

be measured and paid.

Providing and applying Lacquer polish of approved make and finish on new wood

and wood based surface to give an even surface, including cleaning the surface of

all dirt, dust and sand papered smooth and including a coat of wood file after

completion of job etc. to the satisfaction of architects / EIC. (Mode of

measurements: Only the polished area shall be measured & paid for the items in Rupees Three Hundred

74 10.00 which polishing is not inclusive in item description) work shall be carried out as 377.49 Sqm SeventySeven Paise

per the manufacture's specification & sample approved..(Exposed wooden surface FourtyNine Only

at all floor) (Mode of Measurements: Only the polished area shall be measured &

paid for the items in which polishing is not inclusive in item description)

Ply palmet work : Providing and fixing wooden pelmets of upto 150mm/950 mm

x 150 to 600 mm L shape made of 19mm thick ply as per IS 710 MR Grade and

beading of 1.0 mm thick Laminate for curtains/ blinds/ projection screen of

Rupees One Thousand

openings. Rate to be inclusive of lipping, cutting, wastages, necessary fixtures,

75 55.60 nails, adhesives, necessary scaffolding, fixing at all heights and for all floors as per 1,778.38 Rmt

SeventyEight Paise

drawing and approved sample etc finish with veneer semi gloss PU finsh. (Mode

ThirtyEight Only

of Measurements: Only the palmet length shall be measured & paid for the items

in which palmet work is not inclusive in item description)

Lawn plantation : Individual Grass Crop Installation

This work includes the supply and installation of healthy, well-rooted individual

grass plants for the development of a lawn. The surface shall be properly

prepared by leveling, removing debris, and ensuring suitable soil conditions for

Farmyard manure shall be mixed thoroughly with the topsoil before planting to Rupees Six Hundred

76 1460.65 enhance soil fertility and promote healthy grass growth. Individual grass crops 649.22 Sqm FourtyNine Paise

shall be planted at uniform spacing for even coverage and proper rooting. TwentyTwo Only

After installation, the lawn shall be maintained for a period of three months,

including regular watering, weeding, gap filling, trimming, and application of

manure or fertilizer as required to ensure a dense, uniform, and healthy green

Convex Mirror is a curved mirror : Providing and supplying Convex Mirror as per

references image, detail and approved sample by Architect/EIC. The Convex Safety

Mirror is structured with a polycarbonated front and acrylic back which makes it

lighter and easy to place on any exterior. It also looks like a bubble mirror that has

a curvature of the 130-degree view. The Convex Mirror comes with a protective

film coating that makes the traffic mirror scratch-resistant, break-resistant, and

tear-proof.The Polycarbonate Lens reflects a crystal clear and bright image of the

view which can be seen from a long distance. It also magnifies the opposite fronts

that help the drivers to locate small things clearly. The contractor shall Convex Rupees Two Thousand

77 2.00 Mirror with Installation Kit, Nuts & Bolts Included support, Location, any Height 2,903.75 Each Nine Hundred Three Paise

and all complet installation work as per site condition. This Item includes cost of SeventyFive Only

all labour, transfort etc. as required for completing the work in all respects. All

works are carried as per approval and instructions of the architect. Rate shall

inclusive of sample, all materials, loading, unloading, all taxes, transportation,

placing at all floors and for all leads,all accessories as described in item

Road Marking with hot applied thermoplastic paints with reflectorising glass

beads on bitumen/RCC surface providing and laying a hot applied thermoplastic

compound 2.5mm thick including reflectorising glass beads @250gms/m2 area

thickness of 2.5mm is excluding of surface applied glass beads as per IRC: 35-

2015. The finished surface to be levelled, uniform and free from streaks and holes.

Thermoplastic paint shall be used for Zebra Patta, Bump Patta lane, edge line, cut

Rupees Three Hundred

patta, arrows for direction, letter or number writing etc. The white colour

78 12.42 367.72 Sqm SixtySeven Paise

marking should provide liminance co-efficient on cement road shall be min

SeventyTwo Only

mcd/m2/lux and Asphalt road shall be min 100 mcd/m2/lux during the service life

during the day time the marking should make the performance criteria for night

time reflectivity, wet reflectivity and skid resistance as mentioned in the section-

15 of IRC: 35-2015. Warranty for retro reflectivity shall be 2(Two) years.

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Providing and fixing of Corner Guard for Various Flashing in 100mm x 100mm size

in Equal Shape with 5mm edge lipping on both side . The Angle Flashing shall be

made out of 8 to 10 mm thick, The corner guard shall have plastic protective Rupees Three Hundred

79 12.00 guard film of minimum 25 microns to avoid scratches during transportation. The 372.84 Nos SeventyTwo Paise

U track shall be fixed with suitable POP rivet with wall and roof panels with EightyFour Only

minimum spacing of 450 mm c/c. size of guard 1000mm length

Providing and fixing Rumblers strips of required size with any design suggested by

Architectect/ EIC like bottom design, chequered design, anti skid pattern specially

designed for road grip as per drawing & sample approved by Architect which is Rupees One Thousand

80 20.00 covered with premix bituminous carpet at 1m centre to centre at approved 1,788.71 Rmt Seven Hundred EightyEight

locations to control speed marked with white strips of road marking paint etc Paise SeventyOne Only

complete as directed by Engineer in charge.

Cat Eye/Road Stud/RPM : Supplying of Molded TwinShanks Raised Pavement

Markers made of polycarbonate and ABS moulded body and reflective panel swith

micro prismatic lens capable of providing total internal reflection of the

lightenteringthe lens face and shall support a loadof 13635kgs. tested in

accordance to ASTMD4280Type Handcomplying to Specifications of Category A of

MORTH Circular No RW/NH/33023/10-97 DO III Dt 11.06. 1997. The height, width

and length shall not exceed 20mm, 130mm and 130mm and with minimum

Rupees Three Hundred

reflective area of 13Sq cmon each side and thes lope to the base shall be 35+/-5

81 167.00 326.23 Each TwentySix Paise

degree.The strength of detachment of the integrated cylindrical shanks, (of

TwentyThree Only

diameter not less than19+/-2mm and height not less than 30+/2mm) from the

body is to be a minimum value of 500Kgf. Fixing will be by drilling holes on the

road for the shanks togo inside, without nails and using epoxy resin based

adhesive as per manufacturers recommendation and The color of the marker

should be as per the IRC 35-2015 and as directed by Engineer-in-charge.

Fancing : Providing and fixing 'Y' shaped barbed wire fencing on compound wall

top with vertical angle of 50x50x6mmx0.50 mt. height, two cross angle

50x50x6mmx0.45mt. Length, having 3 horizontal and two diagonal rows of

barbed wire (9.38 kg/100 rmt) on vertical angle and three horizontal and two

Rupees Three Hundred

diagonal barbed wire rows on each cross angle incl. cost of barbed wire, necessary

82 251.30 395.85 Rmt NinetyFive Paise EightyFive

GI stapplings, fixing on top of compound wall, painting angle with one coat of

anticorrosive primer and two coats of enamel paint of approved qaulity,

necessary scaffolding etc. complete as per the direction of the Engineer in charge.

Direct Bought Out Item : Providing and placing in position SS brush finish (12 LTS

Rupees One Thousand One

PEDAL BIN/ STEP BIN -) of Kich , Dorma ,etc Square Pedal bin 10x15 Stainless

83 2.00 1,184.73 Nos Hundred EightyFour Paise

Steel Dustbin or Equivalent as per images and as selected by the Architect.

SeventyThree Only

Providing and supplying of Dustbin of Approved Brand Sintex or equivalent of 40- Rupees One Thousand

84 2.00 50 Liters capacity. 1,811.94 Nos Eight Hundred Eleven Paise

NinetyFour Only

Artificial Plant : Providing and supplying planters with plant as per selection of

Architect. Item includes cost of all labour, transfort etc. as required for

Rupees Three Thousand

completing the work in all respects. All works are carried as per approval and

85 10.00 3,153.47 Nos One Hundred FiftyThree

instructions of the architect. Rate shall inclusive of sample, all materials, loading,

Paise FourtySeven Only

unloading, all taxes, transportation, placing at all floors and for all leads.

Providing and fixing Sainless steel signage plate of 1.5mm thick with laser print/

etching and filled with duco paint of approved make including fixing to the wall or Rupees Seven Thousand

86 0.50 door with required acessories and as specified type including fixing etc complete 7,285.33 Sqm Two Hundred EightyFive

as directed by engineer in charge Paise ThirtyThree Only

DOOR MAT : 3M Nomad - Wiping technology - Heavy Duty 7150 - or eqvivalant

approved make Grey Colour: Open Contruction Loop Matting with Crush Resilient

Rupees One Thousand Two

Vinyl with backing. Matting Should be durabe shouldn't Flatten ove time.

87 9.00 1,261.39 Sqm Hundred SixtyOne Paise

Thickness Should be 13mm Min.Suitable for heavy traffic areas, where traffic is

ThirtyNine Only

upto 4 lakh people per year. work complete as per approved sample.

Providing & placing in position DIGITAL CLOCK - WALL MOUNTED as per architect Rupees Two Thousand

88 12.00 selection Ajanta Digital Wall Clock (Brown, Black, With Glass) 2,079.09 Nos SeventyNine Paise Nine

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Signages : Providing and fixing of the following signages using make of cosign or

equivalent approved make by architect.All the detailed work out as per the

detailed drawing and instruction of EIC., specifications and drawings as indicated

there in to all heights and elevation including necessary scaffoldings / supports

/permanant fixing with cement mortor if fixed to ground etc complete in all

Rupees One Thousand

respects.The Signage cost should be inclusive of panels,hanging

89 31.00 1,888.60 Nos Eight Hundred EightyEight

system,bridges,primary & secondary fixings,vinyl,painting,powder coating self

Paise Sixty Only

glowing mateial as directed etc.All shop drawings and coordination with other

services is in scopeof contractor.( At all floor) Size (150 x 600mm) - FACE /WALL

MOUNTED NAME PLATES/SIGNAGES/INFORMATION SIGNAGES (with back lit)

Providing, supplying and placing World Globe - as per sample approved by Rupees Seven Hundred

90 2.00 architect 749.17 Nos FourtyNine Paise

Providing and placing in position vinyl printed MAP of size 54"x65" mm with teak

Rupees Four Thousand

wooden frame with polishing .

91 2.00 4,431.12 Nos Four Hundred ThirtyOne

Paise Twelve Only

Natural Plant : Providing and planting of natural plants, healthy, well-grown, and

free from diseases, of approved species and variety, by Architect.Item includes

cost of all labour, transfort etc. including supply, transportation, handling, Rupees Four Thousand

92 20.00 excavation of pits, planting with good quality garden soil and manure, watering, 4,065.25 Nos SixtyFive Paise TwentyFive

staking, and minimum plant height 10' with pvc pot , complete as directed by the Only

Engineer-in-Charge.

Providing & Laying Tree plantation including providing and fixing tree guard. Rate

also inclusive of maintaining the tree plant in live condition at the time of Rupees Six Hundred

completion of work. Rate are including providing necessary tree guard. ThirtySix Paise Thirty Only

Providing and installation of Granite Foundation stone/inauguration plank 18-

Rupees Six Thousand Two

19mm thick engraved with writing provided by EIC and engraved filled with

94 15.00 6,295.02 Sqm Hundred NinetyFive Paise

golden colour and with a wooden frame.

Providing and Fixing the S.S. 304 Letters with back light of given size as per

Architect's drawings and approved sample or make (Approx Height of each letter

18 to 24 inches) along with all necessary hardwares, scaffolding, Alu/MS Back

Rupees TwentyTwo

support, hanging support and accessories, The rate shall be for complete item

Thousand Six Hundred

95 18.00 inclusive of all material, labour, wastages, necessary tools & tackles, for all floors, 22,649.25 Each

FourtyNine Paise

all heights, all levels and all places within campus. Contractor shall do all the

TwentyFive Only

needful and shall fulfill Architect's design intent. No additional claims will be

entertained for this. (Consider Letter : TALUKA LIBRARY SHAMI)

Providing and Fixing the S.S. 304 Letters of given size as per Architect's drawings

and approved sample or make (Approx Height of each letter 4 to 6 inches) along

with all necessary hardwares, scaffolding, Alu/MS Back support, hanging support

and accessories, The rate shall be for complete item inclusive of all material, Rupees Six Hundred Three

labour, wastages, necessary tools & tackles, for all floors, all heights, all levels and Paise NinetyEight Only

all places within campus. Contractor shall do all the needful and shall fulfill

Architect's design intent. No additional claims will be entertained for this.

Providing and fixing Godess Saraswati idol (Material- Fibre) 5 ft tall, with

Rupees One Lakh FiftySix

proportionately base dimenstion as per approved design by client and complete

97 1.00 1,56,802.50 Each Thousand Eight Hundred

as per instruction of engineer-in charge and consultant.

Two Paise Fifty Only

DIGITAL 2D/3D WALL PAPER : Providing & fixing 2d/3d digital printing printing on

approved paper/canvas/fabric media as per suggested graphic work on suggested

Rupees Two Thousand Six

surface .Contractor shall provide graphic work detail & 5 sqmm sample for

98 18.00 2,671.45 Sqm Hundred SeventyOne Paise

approval the work shall be done inclusive of all rate with accesesories,tool tackel

FourtyFive Only

at all height compelte.

PLUMBING FIXTURE : Providing, fixing, jointing and testing in position of various

Rupees One Thousand

Bathroom C.P. Fixtures with hydraulic testing complete as per design, drawing

99 9.00 1,451.88 Nos Four Hundred FiftyOne

and instruction of site incharge. 25mm Dia Control Valve

Paise EightyEight Only

Providing and fixing screw down bib taps of following size. (B) Brass chromium Rupees Two Thousand

plated screws down Bib Tap. (i) 15mm dia. Paise Ten Only

Providing and fixing health faucet with 1 m PVC tube and swivel hook including all

Rupees One Thousand Five

fittings complete.

101 10.00 1,585.45 Nos Hundred EightyFive Paise

FourtyFive Only

Providing, fixing, jointing and testing in position of various Bathroom C.P. Fixtures Rupees Two Thousand

102 4.00 (Angle Cock) with hydraulic testing complete as per design, drawing and 2,268.41 Nos Two Hundred SixtyEight

instruction of site incharge. Urinal stop cock. Paise FourtyOne Only

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Providing and fixing white glazed vitreous china wall mounting type (European

type) water closet with C.P. bolts, nuts, C.I. Chair or other hanging arrangement,

white solid plastic seat with lid, C.P. brass hinges and rubber buffers, Metropole Rupees Seventeen

flush valve reguler 40mm size (concealed body) with exposed shut off provision , Thousand Nine Hundred

C.P. brass screws and washers complete, including cutting and making good the SixtyEight Paise FourtyOne

walls floors where required. Wall hung EWC matching white plastic seat with lid Only

& CP brass hinges & CP push plate .

Providing and fixing White glazed vitreous Wash Basin Round Over-Counter, size

450 mm dia., with supporting in stone flooring, 1 no, 32 mm CP Bottle trap with Rupees Five Thousand

104 10.00 extension piece to wall flange with rubber adopter for waste connection,1.2m 5,819.81 Nos Eight Hundred Nineteen

Flexible Pipe [1No] and waste coupling. Etc complete. Wash Basin Table Top - Paise EightyOne Only

Providing & fixing in position 15 mm C.P. brass angle cock of best quality with

Rupees Two Thousand

105 13.00 Rmt Long pvc Tube and accessories with necessary fittings etc. complete. 2,000.10 Nos

Providing & fixing in position 15 mm C.P. brass pillar cock of best quality with

Rupees One Thousand

necessary fittings etc. complete.

106 11.00 1,751.75 Nos Seven Hundred FiftyOne

Paise SeventyFive Only

Providing and fixing TOWEL RING SQUARE , as approved by the architect. Work Rupees Nine Hundred

107 7.00 complete including all type of fittings, etc complete as per suggestion of 974.01 Nos SeventyFour Paise One

Architect/EIC. Only

Providing and fixing SOAP DISH HOLDER as approved by the architect. Work

Rupees One Thousand

complete including all type of fittings , etc complete as per suggestion of

108 11.00 1,344.74 Nos Three Hundred FourtyFour

Paise SeventyFour Only

Supply, Installation, Testing & Commissioning vitreous matrix set (For Handicap)

including matrix EWC (European type water closet) with cistern, wall hung matrix

Rupees FiftyThree

wash basin, lever arm faucet for ease of operation, centre pre-punched tap hole,

Thousand Nine Hundred

109 1.00 grab bar with slightly lower height for added convenience & fixed to wall with 53,924.73 Nos

TwentyFour Paise

brackets including cutting and making good the wall and floors as required.

SeventyThree Only

Colour Star White.

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter

Rupees Six Hundred

with jali of the following nominal diameter of self cleansing design with C.I scread

110 28.00 614.19 Each Fourteen Paise Nineteen

down or hinged grating including the cost of cutting and making good the walls.

Providing and fixing Urinal of approved quality including connection with trap and Rupees One Thousand

111 4.00 with integral longitudinal flush pipe.(A) Squating plate pattern white earthenware 1,706.08 Each Seven Hundred Six Paise

550mm x 300mm. Eight Only

Providing and fixing Kitchen sink with C.I. Or M.S. brackets, painted white

Rupees Two Thousand

including cutting holes in walls and making good the same but excluding fittings.

112 2.00 2,326.66 Each Three Hundred TwentySix

(C) Vitreous China Sink.(i) 600mm x 450mm x 150mm size

Paise SixtySix Only

Providing and fixing 600mm x 450mm bevelled edge mirror of superior glass Rupees Eight Hundred

113 11.00 mounted on 6mm thick A.C. sheet or plywood sheet and fixing to wooden pluge 859.41 Each FiftyNine Paise FourtyOne

with C.P. brass screws and washers. Only

SUB EST-01 (Civil Interior, Plumbing Fixure)

Drilling 300mm dia.pilot hole hydrolic drilling machine & drilling trully vertically

(testing by vertically test) bore hole in alluvial strata,any kind of soil

incl.sand,murrum,hard murrum,soft rock,hard rock incl.cost of bentonite powder Rupees One Thousand Six

114 300.00 done by mud flushed rottary equipment bore hole should stand at least for 1,634.20 Rmt Hundred ThirtyFour Paise

27hrs.incl.lowering the pipes in position as directed and incl.supplying and Twenty Only

packing gravel of 4mm to 6 mm size etc. comp. as directed.

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW

(Electric Resistance Welded) FE 410 mild steel screwed and socketed/plain ended

casing pipes of required dia, conforming to IS: 4270, of reputed & approved make,

including painted with outside surface with two coats of anticorrosive paint of

Rupees Three Thousand

approved brand and manufacture, including required hire & labour charges,

115 300.00 3,975.00 Rmt Nine Hundred SeventyFive

fittings & accessories, all complete, for all depths, as per direction of Engineer-in-

(B) 200 mm nominal 6 mm thick

Development of hole by air compressor having capacity 400 cfm/100 psi till sand

Rupees TwentyOne

free discharge of water incl.testing of water supply flow etc. comp. as directed.

116 1.00 21,806.68 Job Thousand Eight Hundred

Six Paise SixtyEight Only

Providing & laying approved make ISI marked HDPE 6Kg / cm2 (Class-3) as per

IS:4984:1995 PE-80 to be erected at road crossing on or floor as directed for Rupees One Hundred

117 250.00 laying of cable. The pipes as following size of dia & weight per 6 mtr 163.62 Rmt SixtyThree Paise SixtyTwo

(B) 50 mm inner Dia. Only

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Supplying & Fixing 50 mm dia heavy top bottom piece,G.I.Bend,Coupling,sand

Rupees Five Thousand

guard MS clamp with Nut Bolt etc.complete as directed by EIC.

118 1.00 5,968.60 Set Nine Hundred SixtyEight

Paise Sixty Only

Water Analysis test in Govt.approved laboratory incl. all water testing etc. comp.

Rupees Three Thousand

119 1.00 3,361.15 Nos Three Hundred SixtyOne

Paise Fifteen Only

Providing water harvesting pit of 5.50 m Dia well and 2.46 mt x 2.46mt x 4.00 mt

size brick masonary well for water logging with excavation in any strata upto four

meter depth, filling the pit with B.T. Metal 40 mm in 0.80 mt. depth with 25- Rupees One Lakh

40mm kapachi, 0.80 mt. depth and 0.50 mt. depth with coarse sand & charcoal in FourtyEight Thousand

layers including making P.V.C. line for water inlet etc. as directed with 300mm dia Three Hundred NinetySix

bore 40 mt. depth and 200mm dia UPVC CM type casing pipe as slott 1.5 to 2.0 Paise EightyThree Only

mm size and ordinary pipe with gravel packing or as directed.

Providing and constructing filter chamber of size 1.50 x 1.50 x 1.50 mt. as Rupees TwentyOne

directed including connection rainwater pipes as per detailed as directed by Thousand Seven Hundred

Engineer in charge including cost of labour and material TwentyOne Paise FiftyFive

RCC Hume Pipe : Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cm.

Rupees Three Hundred

below ground across the road crossing or on floor with necessary material in an

122 50.00 343.40 Rmt FourtyThree Paise Fourty

approved manner and making the ground as per original.(C) 300 mm dia

Construction of granular sub-base by providing close graded Material conforming

to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed

material by tippers to work site, for all leads & lifts, spreading in uniform layers of

Rupees Two Thousand

specified thickness with motor grader on prepared surface and compacting with

123 191.78 2,299.70 Cum Two Hundred NinetyNine

vibratory power roller to achieve the desired density, complete as per

Paise Seventy Only

specifications and directions of Engineer-in-Charge. With material conforming to

Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

Construction of granular sub-base by providing close graded Material conforming

to specifications, mixing in a mechanical mix plant at OMC, carriage of mixed

material by tippers to work site, for all leads & lifts, spreading in uniform layers of

Rupees Two Thousand

specified thickness with motor grader on prepared surface and compacting with

124 191.78 2,416.05 Cum Four Hundred Sixteen Paise

vibratory power roller to achieve the desired density, complete as per

specifications and directions of Engineer-in-Charge. With material conforming to

Grade-II (size range 53 mm to 0.075 mm ) having CBR Value-25

Providing, laying, spreading and compacting graded stone aggregate (size range

53 mm to 0.075 mm ) to wet mix macadam (WMM) specification including

premixing the material with water at OMC in for all leads & lifts, laying in uniform

Rupees Two Thousand

layers with mechanical averfinisher in sub- base / base course on well prepared

125 166.77 2,407.33 Cum Four Hundred Seven Paise

surface and compacting with vibratory roller of 8 to 10 tonne capacity to

ThirtyThree Only

achievethe desired density, complete as per specifications and directions of

Engineer-in-Charge.

SUB EST-02 (General Development & Bore-Well )

Table : Providing & fixing office table / staff table having ht of 750 mm Top,

with 19mm thk plywood as per Architect/ Engineer Design or Selection and Back

and side Ply of table is also made up of 19mm Thick. Top of Table is 19mm thk ply

with laminate Finish Per Requirement and All internal & external Joints finished

with teakwood beading Patti. Item includes fixing of drawers and keyboard tray

and storage with shutters under table as per drawing. With grooves shown as per Rupees TwentyTwo

drawing. All exposed and internal surfaces covered with Laminate Finish of Thousand Nine Hundred

approved shade & Complete as per detail drawings & as instructed by ThirtyEight Paise

Architect/consultant/ Engineer In charge. Complete with all necessary hardware ThirtyEight Only

like nails, ss screws, table chain, TDS channel, adhesives etc. Contractor has to

provide all necessary cut outs for Electrical works & no extra payment shall be

made for it. All ply should follow IS

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Reading Table / Work Station : Providing & fixing work station / table having ht

of 750 mm Top, with MS Pipe Structure of Frame as per Architect/ Engineer

Design or Selection and Back and side Ply of table is also made up of 19mm Thick.

Top of Table is 19mm thk ply with laminate Finish Per Requirement and All

internal & external Joints finished with teakwood beading Patti. Common or front

Part of Table is Sectationized with MS Perforated Sheet. All exposed and internal Rupees TwentyFive

127 91.26 surfaces covered with Laminate Finish of approved shade & Complete as per 25,093.79 Sqm Thousand NinetyThree

detail drawings & as instructed by Architect/consultant/ Engineer In charge. Paise SeventyNine Only

Complete with all necessary hardware like nails, ss screws, table chain, Key board

trey, TDS channel, adhesives etc. Contractor has to provide all necessary cut outs

for Electrical works & no extra payment shall be made for it. All ply should follow

BOOK RACK (MODULAR) :Providing and Placing Book Rack - 1200mm X 400mm X

Rupees Fourteen Thousand

1850mm Material - 0.7 mm thick (+/- 0.07mm) CRCA for Top, Side and Shelf.

128 12.00 14,802.16 No Eight Hundred Two Paise

Finish epoxy powder Coated to the thickness of 50 micron.

Supplying and providing reading chairs with PP arms with soft PU pads, Seat and

back upholstered with PU cushioned and MS powder coated frame and cantilever Rupees Four Thousand

legs. Overall dimension 590 L x 600 W x 915 H (Or as specified) complete as Eight Hundred

directed by architect and product as per given specification. Complete as per SeventyEight Paise Thirty

architectural design and concept and approved by Architect & Client. Only

Chair Type - 01 (Cabin Main Chair) :- Supplying and providing High Back Mesh

office Chair As per specification below:

-Metal frame seat made of Mesh fabric upholstery (foam base)

-Adjustable Head rest

-Fixed Arm rest Rupees Ten Thousand

130 2.00 -Knee tilt mechanism 10,738.07 Nos Seven Hundred ThirtyEight

-360 swivel motion/ 100mm stroke gas Paise Seven Only

-Nylon Star base

-Pushback mechanism & Comfy seating.

-Complete as per architectural design and concept and approved by Architect &

Chair Type - 02 (Cabin Visitor Chair) : Supplying and providing Mid Back Mesh

office Chair As per specification below:

-Metal frame seat made of Mesh fabric upholstery (foam base)

-Center tilt mechanism Rupees Five Thousand

131 4.00 -100mm class 4 gas lift 5,400.98 Nos Four Hundred Paise

-PP Fixed Arm rest NinetyEight Only

-Nylon Star base/Twin wheel nylons casters

-Complete as per architectural design and concept and approved by Architect &

Gang Chair (3 Seater) : Providing and Fixing 3 Seater (moulded foam seat and

back In PU upholstery ) Pero Cross Beam made of powder coated regular MS ERW

tube having 8.0+/-0.03 cm x 4.0 +/- .03 cm x 0.2 +/- 0.014 cm size. Legs to be

chrom plated made of rolled steel with 0.12 +/- 0.013 cm thinkness.Seat and Back Rupees Eighteen Thousand

132 2.00 Shell to be peforated made from cold rolled M.S. Sheet (DIN 1623 Part 1 ST -12 18,003.25 Nos Three Paise TwentyFive

Grade), 0.14 +/- 0.013 cm thickness. The side Bar is made of chrome Plate solid Only

steel 3.0 cm +/- 0.03cm x 1.2 cm +/- 0.03 cm with fluting and plastic inserts. The

Shell to be assembled on the cross beam with help of M8 Bolts.

Providing and Placing News paper Stand 600 W X 900 D X 900 H mm. To be made

from pirme-quality CRCA steel tubes and sheets for durability & longevity, and the

reading top is made from high-quality pre-laminated MDF for a seamless finish Rupees Seven Thousand

133 2.00 and contemporary look. H-type cross bracings, paired with levelling bolts at the 7,160.65 Nos One Hundred Sixty Paise

base, provide extraordinary strength and stability, ensuring steady performance SixtyFive Only

even on uneven floors.

TV UNIT: Providing & fixing projector drawer unit As per detail drawing and

reference image and detail shape & size with require accessories. Top 35 MM th

made from 12 mm th IS 303 ply & Laminate finish Storage body is made of 19mm

303 MR Grade ply with 1 mm laminate finish and inner side 1 mm thick laminate

finish including require nos of drawer with all type of fittings ,cutout for air

cerculation , require fixtures, hardware Hettich/Haffle make etc complete .SS

304 grade conceal handle shall be provide as per approved selection &detailed

Rupees Fifteen Thousand

drawing and instruction of Employer's representative/ Employer.Rate shall

134 1.29 15,651.02 Sqm Six Hundred FiftyOne Paise

incusive require fabrication work considering load capasity of AV equipment.The

work shall be done as per the approved specifications, sample approved and as

directed by the Architect and Engineer-in-charge. The rate shall be for complete

item inclusive of all material, labour, wastages, necessary tools & tackles,

adhesives consumable hardware & required SS 304 grade hardware/accessories

of approved make.

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Low Height Storage : Providing, making, fixing as per detail drawing made from

19 mm IS 710 BWP ply structure aand both side 1 mm thick laminate finish shall

be of approved make & shade and as per the detail drawing. All the edges of ply

shall be covered with 1 mm thick laminate finish Rate shall also inclusive of all

necessary brass satin finish nickel plated/S.S 304 grade hardware like Hinges,

locks,6"handle , 75 mm tower bolts, ball catches/Magnet, The rate shall be in sqm

of elevation area for all floors and at all heights including all costs complete as per

the Architectural drawings & instructions.Only the elevation area of the storage

unit will be measured and paid for. Item for 1 mm thick laminate fixing and

polishing is included in this item. Approval of all loose material (sample of

materials to be used) & raw manufacturing to be got approved in advance from

Rupees Ten Thousand

135 10.39 EIC & Architect prior to the final production of the work. Manufacturing shall in 10,090.02 Sqm

Ninety Paise Two Only

parts or as whole as per the requirements & or assembled at site as per the

requirement and directed by EIC & Architect. All material to be used shall be as

per the drawings & confirm to the relevant detailed material specifications of this

document. The work shall be measured & paid in sqm The rates shall be inclusive

of all wastages, material, labor, taxes, transportation, loading, unloading, fixing in

position, etc. complete to the satisfaction of the Architect and EIC. The mock-up

of 1 unit shall be approved from EIC and Architecture prior to the final

Supplying and Placing Folding Wheel Chair with Overall dimension: (L) 790 x (W)

600 x (H)870mm Frame structure Foldable frame structure is made of section

22x1.2mm A3 carbon steel with chrome finish. Cross bar are made of A3 carbon

steel with section 25.4 x 1.2mm. Rear wheel 24 inch Solid mag wheels with alloy

in the rim Hand rim Integrated hand rim provide to drive the wheel chair of

section 16x1.2mm A3 carbon steel with chrome finish Front wheel 8 inch HUB

made of PA polymer and outer with solid rubber Arm rest PU molded arm rest &

base is made of ABS for better arm support Calf rest & seat Leatherette strap for Rupees TwentyThree

136 2.00 calf rest & leatherette cushion for seat Footrest Adjustable alluminimum die cast 23,230.00 Nos Thousand Two Hundred

foot rest with updown & swivel type mechanism Push handle Handles are made Thirty Only

of moulded rubber grip to push the wheelchair Brakes Hand brakes are provided

to lock the wheelchair at desired location. Foot press Extended base with molded

plastic for better grip Finish Anti rust chrome finish safe working load

100kg.etc.complete as per drawings and design supplied by architect and

instruction given by authority and E.I.C.

SUB EST- 03 (Furniure Work)

Point wiring for Light / Bell with 2-1.5 sq.mm & earth wire of 1.5 sq.mm

(Green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi strand

copper wires up to 10 mtr length , in below type of pipe erected with 6A Modular

type switch / bell push & accessories and earth continuity of following type,

erected on PVC / Metallic/Wooden box, single mounting base frame covered with Rupees Four Hundred

137 96.00 textured/metallic/white front plate modules erected on / in wall / ceiling as per 485.81 Pt. EightyFive Paise EightyOne

pipe erected, with necessary Lamp holder/ceiling rose / H.D.Connector as Only

(f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete Cat-III

Point wiring for secondary light point with 2-1.5 sq.mm & earth wire of

sq.mm (green) both are of ISI marked 1.1 KV grade FRLS PVC insulated multi

strand copper wires, in below type of pipe to be erected complete with earth

continuity and necessary connection with primary light with accessories erected

Rupees One Hundred

on Metal / PVC / wooden box covered with 3 mm thick PC(Polycarbonate) /

138 166.00 167.66 Pt. SixtySeven Paise SixtySix

Acrylic sheet for open / concealed wiring. with necessary Lamp holder / ceiling

rose / H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete Cat-III

Point wiring for Two Way Controlled Light Point with 2-1.5 sq.mm & earth wire

of 1.5 sq.mm (green) both are of .ISI marked 1.1 KV grade FRLS PVC insulated

multi strand copper wires erected in below type of pipe with 6A Modular type

switches and following type of accessories erected on PVC / Metallic/Wooden

box, single mounting base frame covered with textured / metallic/white front Rupees Six Hundred Three

plate modules erected on / in wall / ceiling as per pipe erected. with necessary Paise NinetyEight Only

batten/angle holder or ceiling rose or H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Point wiring for FAN with 2-1.5 sq.mm & earth wire of 1.5 sq.mm (Green) both

are of .ISI marked 1.1 KV Grade FRLS PVC insulated multi strand copper wires up

to 10 mtr length, in below type of pipe erected with 6A Modular type switch and

hum free EME step type electronic fan regulator mounted and accessories with

earth continuity of following type erected on PVC / Metallic/Wooden box, single Rupees Six Hundred

140 42.00 mounting base frame covered with textured/metallic/white front plate modules 674.68 Pt. SeventyFour Paise

erected on / in wall / ceiling as per pipe erected. with necessary ceiling rose / SixtyEight Only

H.D.Connector as directed.

(f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete Cat-III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are

of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to

mtr length, in below type of pipe erected complete with Modular type switch &

pin Plug erected on PVC / Metallic/Wooden box covered with appropriate front

plate modules erected on / in wall / ceiling as per pipe erected with following

Rupees Five Hundred Ten

141 197.00 type of accessories. 510.05 Pt.

Paise Five Only

[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire from nearby

switchboard/mcb db board

(f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete Cat-III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are

of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to

mtr length, in below type of pipe erected complete with Modular type switch &

pin Plug erected on PVC / Metallic/Wooden box covered with appropriate front

plate modules erected on / in wall / ceiling as per pipe erected with following Rupees Seven Hundred

142 7.00 type of accessories 745.38 Pt. FourtyFive Paise

[II] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu. Wire from mcb db ThirtyEight Only

(f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete Cat-III

Point wiring for Individual Plug with & earth wire of 1.5 sq.mm (Green) both are

of ISI marked 1.1 KV grade FRLS PVC insulated multi strand copper wires up to

mtr length, in below type of pipe erected complete with Modular type switch &

pin Plug erected on PVC / Metallic/Wooden box covered with appropriate front

plate modules erected on / in wall / ceiling as per pipe erected with following Rupees Eight Hundred

143 7.00 type of accessories 871.63 Pt. SeventyOne Paise

[III] For 16A Plug and 16 amp switch with 2-4 sq.mm Cu. Wire with 2.5 sq.mm ( SixtyThree Only

green) earthing wire from mcb d b board..

(f) with medium class Rigid PVC pipe and accessories erected concealed in

wall/ceiling complete Cat-III

Point wiring for on board Looped Plug with 6A Modular type switch & 5 pin

socket erected on PVC / Metallic/Wooden box, single mounting base frame Rupees Two Hundred

144 25.00 covered with textured / metallic/white front plate modules erected on / in wall 257.55 Pt. FiftySeven Paise FiftyFive

/ ceiling with following type accessories. Cat-III Only

Providing following type of Modular Type Accessories mounted with PVC /

metallic/Wooden box, single mounting base frame covered with textured /

Rupees One Hundred Sixty

145 2.00 metallic/white front plate , modules erected with necessary connections as per 160.59 Pt.

Paise FiftyNine Only

site situation directed by Engineer In charge. (4) TV Co-axial

Socket outlet Cat.III

Providing following type of Modular Type Accessories mounted with PVC /

metallic/Wooden box, single mounting base frame covered with textured /

Rupees One Hundred Sixty

146 30.00 metallic/white front plate , modules erected with necessary connections as per 160.59 Ea.

Paise FiftyNine Only

site situation directed by Engineer In charge. (7) Blank Plate

Providing & erecting Switch board for Computer or electric apparatus consisting

of following modular type accessories mounted with PVC / Metallic

concealed/open box with single mounting base frame covered with

textured/metallic /white front plate,modules erected with necessary connections Rupees One Thousand One

147 18.00 as directed 1,133.22 Ea. Hundred ThirtyThree Paise

1 no. 6A/16A universal plug-switch combined. TwentyTwo Only

3 nos. 6A Switch

3 nos. 6A 5 pin Plug

For Modular Type Accessories

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size

complete to be erected on/in wall or ceiling erected with necessary PVC fittings &

Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, Rupees TwentyFive Paise

in approved manner as directed. TwentyFive Only

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be erected

concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC Rupees One Thousand One

149 1517.00 insulated stranded wire of green colour for earth continuity of following size 1,133.22 Ea. Hundred ThirtyThree Paise

(A) with medium class Rigid PVC pipe and accessories TwentyTwo Only

(a) 2 wire 1.5 sq. mm

Providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be erected

concealed in /flushed on wall/ceiling, with 1.5 sq. mm copper conductor FRLS PVC

Rupees ThirtyThree Paise

150 363.00 insulated stranded wire of green colour for earth continuity of following size 33.33 Mtr.

ThirtyThree Only

(A) With medium class Rigid PVC pipe and accessories

(b) 2 wire 2.5 sq. mm

providing and erecting Mains with 1.1 KV grade FRLS PVC insulated ISI marked

stranded Copper conductor wire in following type of pipe to be erected in / on

wall / ceiling with 2.5 sq. mm copper conductor FRLS PVC insulated stranded wire

Rupees SixtyTwo Paise

151 176.00 of green colour for earth continuity of following size 62.62 Mtr.

(A) with medium class Rigid PVC pipe and accessories (a

2 wire 4 sq. mm

Lighting Fixtures ,Fan & other items :Providing and erecting decorative wall

bracket fittings complete with LED lamp and rust free fittings components

Rupees One Thousand

mounted in chrome finish housing with holder ,clear/opaque glass diffuser

152 21.00 1,712.96 Ea. Seven Hundred Twelve

complete erected with lead wires with minimum 15 wattage capacity as per

Paise NinetySix Only

instruction engineer incharge/architect/authority .cat-III

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to

Watt assembled on single MCPCB, with housing used as a heat sink shall be made

of thick sheet Steel conforming to IS: 513/CRCA/aluminium pressure die cast

powder coated and high U.V. & corrosion resistance with diffuser housed in

aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Rupees Four Hundred

Luminaire efficacy> 85 lumens/watt

153 15.00 427.23 Ea. TwentySeven Paise

LED driver efficiency > 85 %

TwentyThree Only

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for

spring loaded mounting clips complete.IP20

(ii) 11-15 watts, Surge-2 KV KV cat-III

Supplying and erecting LED indoor fittings with LEDs of wattage 0.2 Watt to

Watt assembled on single MCPCB, with housing used as a heat sink shall be made

of thick sheet Steel conforming to IS: 513/CRCA/aluminium pressure die cast

powder coated and high U.V. & corrosion resistance with diffuser housed in

aluminium casted body with company mark/name

160V to 270V,Power Factor more than 0.95, THD < 15 %,

CCT 3000 K to 6500K,

Rupees Five Hundred

Luminaire efficacy> 85 lumens/watt

154 189.00 589.84 Ea. EightyNine Paise

LED driver efficiency > 85 %

EightyFour Only

( fitting required LM-79 & LM-80 Certificates)(NOTE: Below description have

shown ranges of Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.)

(A) Square/ Circular shaped Surface/Recessed Mount Downlight with provision for

spring loaded mounting clips complete.IP20

(iii) 16-20 watts, Surge-2 KV cat-III

Supplying and erecting LED street light / Flood light fittings with High power

White LEDs wattage of 3 Watt and above assembled on single MCPCB, efficiency

more than 130 lm/w and corrosion free High pressure die cast aluminum housing

with smooth finish powder coated and heat sink extruded aluminium with

diffuser and Polycarbonate optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V,Power Factor more than 0.95,

THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 Rupees Six Thousand Five

155 39.00 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79 & LM-80 6,566.01 Ea. Hundred SixtySix Paise One

certificates)(NOTE: Below description have shown ranges of Wattage capacity of Only

LED fittings.The Engineer incharge may select any wattage capacity between the

(A) Street Light (IP-65), Surge protection -4KV integral and ,Light must have

440VAC line supply with over-voltage protection. (iv)

above 90 to 120 watts Cat-lll

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Supplying and erecting LED street light / Flood light fittings with High power

White LEDs wattage of 3 Watt and above assembled on single MCPCB, efficiency

more than 130 lm/w and corrosion free High pressure die cast aluminum housing

with smooth finish powder coated and heat sink extruded aluminium with

diffuser and Polycarbonate optics/ lenses, with toughened glass with company

mark/name engraved or embossed 160 to 270 V,Power Factor more than 0.95,

THD < 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45, Luminaire efficacy> 100 Rupees Eight Thousand

156 11.00 lumens/watt . LED driver efficiency > 85 %.( fittings required LM-79 & LM-80 8,453.70 Ea. Four Hundred FiftyThree

certificates)(NOTE: Below description have shown ranges of Wattage capacity of Paise Seventy Only

LED fittings.The Engineer incharge may select any wattage capacity between the

(B) Flood Light (IP-65), Surge protection -4KV integral and ,Light must have

440VAC line supply with over-voltage protection. (v)

above 120 to 160 watts Cat-lll

Supply, Installation, Testing and Commissioning of suitable sweep, BEE 5 Star

rated, Ceiling fan with Brush Less Direct Current (BLDC) permanent ferrite

magnet Motor, class of insulation: B, Rust free 3 nos.Aluminium blades, 2 nos.

canopies, shackle kit with earthing provision, copper winding, Power factor not <

0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM,

RPM,230v (tolerance as per IS : 374-2019), THD < 10%, with remote unit for Rupees Two Thousand

157 1.00 Speed Control and all remaining accessories including safety pin, nut bolts, 2,799.72 Ea. Seven Hundred NinetyNine

washers, temperature rise = 75 degree C (Max.), suitable for 140 to 285 Voltage Paise SeventyTwo Only

and rectifier circuit with surge, over current and overload protection , 50 Hz,

Single phase AC Supply, earthing etc. Complete as required.[ Make shall be

approved by Engineer in Charge]

(A)900 mm sweep (36")

Supply, Installation, Testing and Commissioning of suitable sweep, BEE 5 Star

rated, Ceiling fan with Brush Less Direct Current (BLDC) permanent ferrite

magnet Motor, class of insulation: B, Rust free 3 nos.Aluminium blades, 2 nos.

canopies, shackle kit with earthing provision, copper winding, Power factor not <

0.9, Service Value (CMM/W) minimum 6.85, Air delivery minimum 215 CMM,

RPM,230v (tolerance as per IS : 374-2019), THD < 10%, with remote unit for Rupees Two Thousand

158 41.00 Speed Control and all remaining accessories including safety pin, nut bolts, 2,885.57 Ea. Eight Hundred EightyFive

washers, temperature rise = 75 degree C (Max.), suitable for 140 to 285 Voltage Paise FiftySeven Only

and rectifier circuit with surge, over current and overload protection , 50 Hz,

Single phase AC Supply, earthing etc. Complete as required.[ Make shall be

approved by Engineer in Charge]

(B) 1200 mm Sweep (48")

Supplying and erecting 19 / 20 mm. nominal bore Medium Class M.S. Pipe down

Rupees One Hundred Eight

159 10.00 rod erected duly painted for fan complete with proper insulation without leakage 108.07 Mtr.

Paise Seven Only

Supplying & erecting fan hook box of 10 mm M.S. round bar bounded to the

RCC bars up to 50mm length each side and pierced through a 16 Gauge M.S. box Rupees One Hundred Eight

/ Heavy Duty PVC box complete erected concealed in Ceiling with necessary Paise Seven Only

Providing 2.5mm.thick laminated acrylic sheet to cover the fan hook or Fan box. Rupees Eighteen Paise

Supplying & erecting approved make low noise decorative exhaust fan having Rupees One Thousand

162 8.00 square frame ABS body with inbuilt lowers & square frame.For 200mm with 1350 1,703.87 Ea. Seven Hundred Three Paise

RPM cat-ii EightySeven Only

Street Light poles : Supplying & erecting Galvanized M.S pipe post “B” class

mm O.D 4 mtr. Long duly painted with two coats of aluminium paint complete Rupees Three Thousand

163 39.00 with metallic base plate of 300 mm x 300 mm x 4mm thick for using as a 3,225.94 Ea. Two Hundred TwentyFive

compound light pole with approx. weight 32 Kg. Paise NinetyFour Only

Providing 1:2:4 cement concrete foundation & 70 % PCC from bottom including

excavation for the pole of size 45 x 45 x 100 cm. Deep in below ground level with

plinth of 45 cm x 45 cm (or 45 cm dia x 45 cm) high upper ground level with Rupees Eight Hundred

necessary curing and finishing in approved manner. Nine Paise One Only

( for 4 & 6 mtr pole)

Supplying & erecting approved make SMC press moulded composite FRP. loop-

in, loop-out approx. 2mm thick box complete with Bakelite connector strip

5way(3P+N+E),DIN rail for mounting mob & hinged doors as per requirement Rupees Eight Hundred

165 39.00 having locking arrangements with mounting clamp with nuts, bolts & washers 898.90 Ea. NinetyEight Paise Ninety

suitable for erection on pole with cable clamps& earth bolt of following size of Only

box. (A) 300mm x 200mm x

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Providing and erecting street light pole bracket comprising main B Class GI pipe of

4.2 cm/require outside dia. complete with suitable B Class G.I sleeve tubing of

approx. 45cms.length and suitable for 76.5 mm / 80mm. / require size pole top

having sufficient fasteners for fixing the brackets and having spread of 1 mtr.

Rupees Six Hundred

166 37.00 length with suitable rise as per site condition & suitable welded stiffener reducer 614.08 Ea.

Fourteen Paise Eight Only

and nipple with check nut complete painted with one coat of Red oxide / PU base

primer and two coats of Aluminium / PU paint. paint with following nos of arms.

[a] Single Arm bracket 1 Mtr

Providing and erecting street light pole bracket comprising main B Class GI pipe of

4.2 cm/require outside dia. complete with suitable B Class G.I sleeve tubing of

approx. 45cms.length and suitable for 76.5 mm / 80mm. / require size pole top

having sufficient fasteners for fixing the brackets and having spread of 1 mtr.

Rupees Eight Hundred

length with suitable rise as per site condition & suitable welded stiffener reducer

167 2.00 829.21 Ea. TwentyNine Paise

and nipple with check nut complete painted with one coat of Red oxide / PU base

primer and two coats of Aluminium / PU paint. paint with following nos of arms.

[B] Double Arm Bracket 1 Mtr

Supplying & erecting approved make Digital time switch having lithium cell

years operative and operate battery backup 1 channel day clock with 14 memory

programme, suitable to operate on 240V + 5%, 16A with, floating contacts

Rupees Three Thousand

Minimum switching setup time 1 minimum & LCD display. Also comprised

168 1.00 3,168.37 Ea. One Hundred SixtyEight

permanent ON/OFF switching. Programming switches & housed in fire proof

Paise ThirtySeven Only

thermoplastic enclosure & transparent cover erected as required with necessary

connection erected as directed.

Supplying & erecting power contactor ,AC3 duty for time switch complete erected

Rupees Two Thousand

as per direction Cat III (D) 4 pole

169 1.00 2,782.55 Ea. Seven Hundred EightyTwo

Paise FiftyFive Only

Panel & Switchgear : Providing and erecting Approved make Four pole moulded

case circuit breaker having breaking capacity ICU of 25 KA. at 415 V,having

normal current rating up to 25 A to 100A. with Fixed thermal & magnetic release Rupees Six Thousand One

170 21.00 suitable to work on A.C. supply 50 c/s. with all internal connections, spreader 6,173.12 Ea. Hundred SeventyThree

tinned copper & complete erected in existing 16 G.M.S. housing. Paise Twelve Only

ICS=100% of ICU only Cat III

Providing and erecting Approved make Four pole moulded case circuit breaker

having breaking capacity ICU of 35 KA. at 415 V. having Normal current rating

Rupees Sixteen Thousand

200A.with variable Thermal & magnetic release suitable to work on A.C.supply

171 2.00 16,221.61 Ea. Two Hundred TwentyOne

c/s. with all internal connections, spreader tinned copper & complete erected in

Paise SixtyOne Only

existing 16 G.M.S.housing. ICS=100% of ICU only Cat III

Providing and erecting Approved make Four pole moulded case circuit breaker

having breaking capacity ICU of 35 KA. and above at 415 V . having normal

Rupees Twenty Thousand

current rating 250A. with variable thermal & magnetic release suitable to work

172 1.00 20,946.39 Ea. Nine Hundred FourtySix

on A.C.supply 50 c/s. with all internal connections, spreader tinned copper &

Paise ThirtyNine Only

complete erected in existing 16 G.M.S. housing. Cat III

Panel Mounting Busbars : Supplying and erecting triple pole & neutral 440V/

500V panel mounting Aluminium Busbars with four equal Nos. of bus having

current density not more than 0.8 Amp. / sq.mm (Rated current / cross section

Rupees One Thousand

area) duly wrapped with colour insulating tape for phase sequence of following Rn.Mt

173 10.00 1,037.27 ThirtySeven Paise

current carrying capacity, erected with necessary bus bar supports /insulators, r

TwentySeven Only

main cable socket to each busbar,erected in existing cubical panel with necessary

connections. (B) Suitable for

200 Amp. capacity

Providing and erecting Approved make Earth fault Relay suitable to mount with

inter connection suitable to following size of moulded case circuit breaker having

Rupees Five Thousand

CT ratio & MCCB rating as following along with shunt trip 220V AC. with all

174 1.00 5,415.62 Ea. Four Hundred Fifteen Paise

internal connections & complete erected in existing M.S.housing.

providing and erecting Miniature circuit breaker single pole 6A to 25A suitable

to operate on 240 V A.C. system and having breaking capacity 10 KA to be Rupees One Hundred

erected in existing box. confirming to IS 8828/1996 with ISI Mark Cat.III Twelve Paise Eleven Only

Providing & erecting 240 V MCB double pole switch for motor & inductive load

Rupees Two Hundred

(C Curve) having 10 KA breaking capacity & confirms to IS : 8828 in existing box

176 44.00 299.97 Ea. NinetyNine Paise

having following capacity (A) 6 to

NinetySeven Only

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Providing and erecting 415 Volt MCB four pole motor & inductive load(c Curve)

Rupees Six Hundred

having 10 KA Breaking capacity and confirms to IS : 8828 in existing metal box

177 1.00 668.62 Ea. SixtyEight Paise SixtyTwo

having following capacity. (B) 40 Amp.

Providing and erecting 415 Volt MCB four pole motor & inductive load(c Curve)

Rupees Seven Hundred

having 10 KA Breaking capacity and confirms to IS : 8828 in existing metal box

178 3.00 737.30 Ea. ThirtySeven Paise Thirty

having following capacity. (C) 63 Amp.

Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C Curve)

Rupees Six Hundred

having 10KA breaking capacity & confirms to IS :8828 in existing box having

179 2.00 647.41 Ea. FourtySeven Paise

following capacity (b)40

Providing & erecting 415 V MCB three Pole for Motor & Inductive Load (C Curve)

having 10KA breaking capacity & confirms to IS :8828 in existing box having Rupees Seven Hundred

following capacity (c)63 Sixteen Paise Nine Only

providing and erecting Approved make RCCBs conforming to IS: 12640 and having

sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and suitable for

operation on single phase 240 V,50Hz. having characteristic of quick action & Rupees One Thousand

181 3.00 tripping with all advance feature & do not incorporate any electronic component. 1,969.50 Ea. Nine Hundred SixtyNine

for following Max. rating erected as directed Paise Fifty Only

(i) 25 Amps.DP Cat. III

providing and erecting Approved make RCCBs conforming to IS: 12640 and having

sensitivity of 30 mA and Short Circuit withstand capacity of 10 KA and suitable for

operation on single phase 240 V,50Hz. having characteristic of quick action & Rupees Two Thousand

182 10.00 tripping with all advance feature & do not incorporate any electronic component. 2,235.13 Ea. Two Hundred ThirtyFive

for following Max. rating erected as directed Paise Thirteen Only

(ii) 40Amps. DP Cat. III

Providing and erecting Sheet Steel powder coated MCB distribution board -

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate

nos. of MCBs.(The DBs should be used of same company of MCB to be used) Rupees Two Thousand

183 2.00 suitable for 2,913.85 Ea. Nine Hundred Thirteen

(B) three phase incoming and single phase horizontal type outgoing Per phase Paise EightyFive Only

isolation type (PPI)

(b) sheet steel double door

Providing and erecting Sheet Steel powder coated MCB distribution board -

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate

nos. of MCBs.(The DBs should be used of same company of MCB to be used) Rupees Three Thousand

184 1.00 suitable for 3,874.36 Ea. Eight Hundred SeventyFour

(B) three phase incoming and single phase horizontal type outgoing Per phase Paise ThirtySix Only

isolation type (PPI)

(b) sheet steel double door

Providing and erecting Sheet Steel powder coated MCB distribution board -

flush / surface mounted fitted with busbar, neutral link, earth bar and DIN rail,

Conforms to IS 8623-1 & 3, IEC 61439-1 & 3 without MCB to house appropriate

nos. of MCBs.(The DBs should be used of same company of MCB to be used) Rupees Four Thousand Six

185 1.00 suitable for 4,666.20 Ea. Hundred SixtySix Paise

(B) three phase incoming and single phase horizontal type outgoing Per phase Twenty Only

isolation type (PPI)

(b) sheet steel double door

Providing and erecting Sheet Steel powder coated Vertical MCB distribution board

(VTPN) - flush / surface mounted double door (IP54) fitted with copper insulated

busbar, isolated neutral bar, earth bar and DIN rail, Conforms to IS 8623-1 & 3, Rupees Nine Thousand

186 1.00 IEC 61439-1 & 3, suitable for 250 AMP TPN MCCB + RCCB as incomer and three 9,921.23 Ea. Nine Hundred TwentyOne

phase outgoing as per following .(The DBs should be used of same company of Paise TwentyThree Only

MCB to be used) (B)6 way outgoing

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Earthing : Supplying & erecting in earthpit of minimum bore dia. 225mm size

approved make Safe Earthing Electrode consisting Pipe-in-Pipe Technology as per

IS 3043-1987 made of corrosion free hot dipped G.I.Pipes having Outer pipe dia

of 80 mm having 80-200 Micron galvanising, Inner pipe dia of 40 mm having 200-

250 Micron galvanising, connection terminal dia of 14 mm with constant ohmic

value surrounded by highly conductive compound with high charge dissipation

suitable for following type of applications with chamber and heavy duty cover

(A)(approved make OEM has to submit test certificate including value of earth

resistance of installation duly stamped and signed by agency and officer Incharge

has to ensure the value of earthing resistane mentioned in test Certificate) &

Rupees Ten Thousand Five

having back filling compound of (B) Inner chemical (CCM Compound)- Resistivity:-

187 12.00 10,593.89 Ea. Hundred NinetyThree Paise

0.2 ohm / meter testing as per IEC 62561-2017, Voltage drop:- < 1 volt at no load

EightyNine Only

& dry form, Sulphar content:- <2%(C) Back fill Compound :- Earthing compound

should be capable to retain moisture for long time Necessary test report must be

submitted by Agency.

(c) For Electrical Installation covering Transformer Neutrals, Lightning arrester

Earthing, A.C.Plant & Sensitive Computer System(like Automation, SCADA) i.e

independent Earthing in normal soil.

Length of Pipe : 3.00 mtrs

Back filling Compound :2 nos Bags of 25 Kg.

Cupboards : Providing & erecting weather proof, dust & vermin proof, floor

mounted front operated indoor type cubical panel board necessary IP-42 and

above protection as per approval from engineer incharge made from 14 SWG

thick CRC M.S. sheet for outer body & doors, 16 SWG thick CRC M.S.sheet for

internal partitions with necessary accesories , supporting angles/ flats channel

including cutting, bending, drilling, welding, riveting with internal partitions &

cable alley as per requirements & instruction of engineer-in-charge with erection

of supplied switch gears, BUSBARS, suitable size of inter connecting PVC copper

wire / copper-aluminium strips, rubber grommets, rib, bakelite control fuses/MCB Rupees Fourteen Thousand

188 10.00 for measuring instruments, earth bus & earth bolts, foundation flange - bolts- 14,902.55 Nine Hundred Two Paise

base Plates, sufficient nos. of hinged doors, handles with locking arrangement and FiftyFive Only

rubber gasket,heavy duty end terminal connection,danger notice board,necessary

ventilation,earthing strip complete. The Panel shall be painted with epoxy

powder coating.

(B) The standard companies switch gear shall be used and only manufacturers at

CPRI approved factory

(i) with 350mm depth

Providing and erecting ,Fabricating the box type items made from M.S. Sheet

with A.I. supports, wings, doors, handles other hardware materials as per Rupees One Hundred

189 80.00 requirement design with finishing by three tank powder coating processed inside 180.79 Kg. Eighty Paise SeventyNine

and outside painted, erected as directed including minor civil work. Only

Cables : Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable

multistrand Aluminium conductor for 1.1 KV. to be laid on wall with necessary

Rupees Two Hundred

190 66.00 clamps or in existing trench / pipe of following size of cables 220.18 Mtr.

Twenty Paise Eighteen Only

(B) 3 1/2 core 35 Sq. mm ( 16 Sq. mm 1/2 core)

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in Rupees Two Hundred

191 110.00 existing trench / pipe of following size of cables (C) 284.82 Mtr. EightyFour Paise EightyTwo

3 1/2 core 50 Sq. mm ( 25 Sq.1/2 mm core) Only

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in Rupees Three Hundred

192 110.00 existing trench / pipe of following size of cables (D) 378.75 Mtr. SeventyEight Paise

3 1/2 core 70 Sq. mm ( 35 Sq. mm 1/2 core) SeventyFive Only

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in Rupees Five Hundred

193 50.00 existing trench / pipe of following size of cables (F) 540.35 Mtr. Fourty Paise ThirtyFive

3 1/2 core 120 Sq. mm ( 70 Sq. mm 1/2 core) Only

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand

Rupees One Hundred

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in

194 44.00 153.52 Mtr. FiftyThree Paise FiftyTwo

existing trench / pipe of following size of cables (A)

4 core 16 Sq. mm

Providing and erecting XLPE (IS:7098)(I)-88 ISI armoured cable multistrand

Rupees One Hundred

Aluminium conductor for 1.1 KV. to be laid on wall with necessary clamps or in

195 110.00 190.89 Mtr. Ninety Paise EightyNine

existing trench / pipe of following size of cables (B)

4 core 25 Sq. mm

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand / Solid

Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in Rupees Three Hundred

196 110.00 existing trench / pipe at road crossing or floor of following size of cables. 364.61 Mtr. SixtyFour Paise SixtyOne

(B) 4 core 4 Sq. mm Only

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand / Solid

Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in

Rupees Five Hundred Ten

197 853.00 existing trench / pipe at road crossing or floor of following size of cables. 510.05 Ea.

Paise Five Only

(C) 4 core 6 Sq. mm

Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured cable multistrand

Copper conductor for 1.1 KV. to be laid on wall with necessary clamps or in Rupees Six Hundred

198 143.00 existing trench / pipe at road crossing or floor of following size of cables. 676.70 Ea. SeventySix Paise Seventy

(A) 4 core 10 Sq. mm Only

Providing and, fixing heavy duty flange type brass cable gland with rubber ring

for PVC insulated armoured cable complete with out going tails, insulating tape Rupees ThirtyThree Paise

etc for following size of cables. (A) 2 to 4 core 2.5 ThirtyThree Only

Providing and, fixing heavy duty flange type brass cable gland with rubber ring

for PVC insulated armoured cable complete with out going tails, insulating tape Rupees ThirtyEight Paise

etc for following size of cables. (B) 2 to 4 core 6 ThirtyEight Only

Providing and, fixing heavy duty flange type brass cable gland with rubber ring

for PVC insulated armoured cable complete with out going tails, insulating tape Rupees ThirtyEight Paise

etc for following size of cables. (C) 2 to 4 core 10 ThirtyEight Only

Providing and, fixing heavy duty flange type brass cable gland with rubber ring

for PVC insulated armoured cable complete with out going tails, insulating tape Rupees FourtySeven Paise

etc for following size of cables. (D) 2 to 4 core 16 FourtySeven Only

Providing and, fixing heavy duty flange type brass cable gland with rubber ring

for PVC insulated armoured cable complete with out going tails, insulating tape Rupees FiftyOne Paise

etc for following size of cables. (E) 2 to 4 core FiftyOne Only

Providing and, fixing heavy duty flange type brass double compression type

cable gland with rubber ring for PVC insulated armoured cable complete with out

Rupees SeventyFive Paise

204 4.00 going tails, insulating tape etc for following size of cables. 75.75 Ea.

SeventyFive Only

(B) 3 & 1/2 core 35/50 Sq. mm

Providing and, fixing heavy duty flange type brass double compression type

cable gland with rubber ring for PVC insulated armoured cable complete with out

Rupees One Hundred

205 2.00 going tails, insulating tape etc for following size of cables. 103.02 Ea.

Three Paise Two Only

(C) 3 & 1/2 core 70 Sq. mm

Providing and, fixing heavy duty flange type brass double compression type

cable gland with rubber ring for PVC insulated armoured cable complete with out Rupees One Hundred

206 2.00 going tails, insulating tape etc for following size of cables. 140.39 Ea. Fourty Paise ThirtyNine

(E) 3 & 1/2 core 120 Sq. mm Only

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of

following size evenly crimped with high pressure tool & connected to switchgear

Rupees Thirteen Paise

207 26.00 terminals with brass/cadmium plated nut bolts in an approved manner. 13.13 Ea.

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of

following size evenly crimped with high pressure tool & connected to switchgear

Rupees Fifteen Paise

208 37.00 terminals with brass/cadmium plated nut bolts in an approved manner. 15.15 Ea.

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of

following size evenly crimped with high pressure tool & connected to switchgear

Rupees Twenty Paise

209 18.00 terminals with brass/cadmium plated nut bolts in an approved manner. 20.20 Ea.

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of

following size evenly crimped with high pressure tool & connected to switchgear

Rupees TwentyFive Paise

210 9.00 terminals with brass/cadmium plated nut bolts in an approved manner. 25.25 Ea.

TwentyFive Only

Solder less crimping type Aluminium lugs conforming to IS suitable for cable of

following size evenly crimped with high pressure tool & connected to switchgear

Rupees FourtyFive Paise

211 7.00 terminals with brass/cadmium plated nut bolts in an approved manner. 45.45 Ea.

FourtyFive Only

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Solder less crimping type Copper lugs conforming to IS suitable for cable of

following size evenly crimped with high pressure tool & connected to switchgear

Rupees Eight Paise Eight

212 141.00 terminals with brass/cadmium plated nut bolts in an approved manner. 8.08 Ea.

Danger Sign boards : Providing and erecting metallic vitrified danger notice board

Rupees SixtyNine Paise

213 2.00 as per language suggested by engineer incharge for MEDIUM VOLTAGE 69.69 Ea.

installation to be erected as per IS-2551.

Providing & erecting Medium Voltage Danger Notice Board sticker as per

Rupees TwentySix Paise

214 2.00 language suggested by engineer incharge of standard size as per IS-2551 26.26 Ea.

Miscellaneous : Providing & laying. R.C.C. Hume pipe for cable to be laid 90 cm.

Rupees Three Hundred

below ground across the road crossing or on floor with necessary material in an

215 60.00 343.40 Mtr. FourtyThree Paise Fourty

approved manner and making the ground as per original.

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary connecting accessories of

Rupees NinetyFive Paise

216 360.00 same material at required depth in existing trench for laying of cable. below 95.95 Mtr.

NinetyFive Only

ground / road surface for enclosing cable (C))90 mm outer

Providing & laying approved make Double walled corrugated pipes (DWC) of

polyethylene(conforming to IS 14930 II )with necessary connecting accessories of Rupees One Hundred

217 80.00 same material at required depth in existing trench for laying of cable. below 137.36 Ea. ThirtySeven Paise ThirtySix

ground / road surface for enclosing cable (D)120 mm Only

Making trench in all soil of suitable width of 90 cm deep for laying cable or

Rupees FiftyFive Paise

218 500.00 locating the fault all over the run and back filling the same and making the 55.55 Ea.

surface as normal ground.

Meters & Panel Accessories : Supplying and erecting approved make panel

Rupees One Thousand Two

mounting type Digital Voltmeter having 3 digits LED display, 0 to 750 AC Volts

219 3.00 1,275.63 Ea. Hundred SeventyFive Paise

range erected on existing panel board with all connection, wiring etc .with

SixtyThree Only

manufacturers calibration certificate.

Supplying and erecting approved make panel mounting type Digital Ammeter

having 3 digits LED display, external CT operated, calibrated for 0 to 1000 Amps Rupees One Thousand Five

220 3.00 suitable to operate on 500 Volt AC , erected on existing panel board with all 1,558.43 Ea. Hundred FiftyEight Paise

connection, wiring etc .with manufacturers calibration certificate. FourtyThree Only

Supplying and erecting Ammeter / Voltmeter selector switch for 3 phase AC Rupees Three Hundred

221 3.00 Supply 500 V on existing panel board with necessary connections. 317.14 Ea. Seventeen Paise Fourteen

Providing & erecting L.T. Current Transformer with bar primary 50/5 to 1000/5 Rupees Two Hundred

222 3.00 ratio 15 VA burden erected in existing CRCA box duly secured with insulating 274.72 Ea. SeventyFour Paise

materials connected to the meter SeventyTwo Only

Supplying and erecting approved make set of indicator lamps of LED type lamp,

Rupees FourtyThree Paise

223 9.00 lens cover, Bakelite holder complete erected with necessary connections. 43.43 Ea.

FourtyThree Only

Substation Equipments : Providing and fixing printed instruction chart both in

Rupees One Hundred

English and Gujarati and duly framed with front glasses, for treatment of person

224 1.00 130.29 Ea. Thirty Paise TwentyNine

suffering from Electric shock with minimum 50" diagonally size.

Providing pair of rubber hand gloves suitable for working on 11 KV/22 KV supply.

Rupees Two Hundred

Fourteen Paise Twelve Only

Supplying rubber matting of following thickness as per IS:15652/IEC 61111 Rupees One Thousand

226 8.00 (b)4mm 1,027.17 TwentySeven Paise

Supplying stand first AID box with antiseptic cream, medicine for use on wounds

due burn, crepe bandage, gauge bandage, medicated ready to use bandage (Band- Rupees Two Hundred

227 2.00 aid) adhesive tape for medicinal user, Scissors, anti-septic solution (Savlon or 299.97 Ea. NinetyNine Paise

similar) etc. (All above contents shall be of standard makes) NinetySeven Only

Supplying FIRE bucket round bottom of 9 litres capacity made out of 24 gauge

G.I. sheet with extra handle at bottom duly painted white inside and Red out side Rupees Two Hundred

with FIRE mark, filled with dry-sand and kept on existing stand provided or hung Fourteen Paise Twelve Only

Wall hook 22 to 25 cms. projection for keeping fire buckets made out of 15 mm Rupees Sixty Paise Sixty

dia. M.S rod grouted in wall to a depth of minimum 15 cms. Only

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

UPS : Supplying and erecting approved make online Un-interruptible Power

Supply system comprising flat cum-boost charger with IGBT base rectifier &

Inverter & sealed maintenance free SMF batteries. The charger having operating

capacity for input 160-270V AC & inverter having output 230V,50 Hz Ac with

Rupees Two Lakh Seventy

load power factor with battery, over/under voltage output with over load & short

230 1.00 2,70,989.06 Ea. Thousand Nine Hundred

circuit protection equipment. The system housed in CRC sheet duly powder

EightyNine Paise Six Only

coated paint with following power backup.with MS painted batteries stand, 10%

Overload capacity for momentary load.

(I) 10 KVA 3 - phase with 1Hr Backup

Lighting Arrester : SITC of Vertical Air Termination Solid aluminium with Base-

mm dia and 1000 mm long. Air Termination Base tested for conditioning, Ageing

Rupees Nine Thousand

Test & Lightning impulse current withstand test: 100 kA of 10/350µs waveform in

231 1.00 9,416.23 Ea. Four Hundred Sixteen Paise

an accredited Third party laboratory as per 6.3 & 6.4 of IEC 62561-1

TwentyThree Only

protocol with MAST 34mm dia 3000 mm long- Cold Galvanized

SITC of 8 mm dia solid Aluminium Conductor for roof top mesh grid and tested

as per IEC 62561- 2 conducted in the Govt. accredited thirty party laboratory to

meet the requirement of IS/IEC 62305 with Required Accessories - Aluminium

Holding clamp at every 1 mtr distance, Aluminium/SS cross splicer at every

crossing of Alu. conductor, Expansion piece with connectors at every 20 mtr

Rupees Two Hundred

distance, Aluminium straight Splicer to connect conductors. All Accessories

232 80.00 299.97 Mtr NinetyNine Paise

should be tested as per IEC 62561-1 2018 Cl. 6.3 for conditioning & Ageing Test &

NinetySeven Only

6.4 for Lightning impulse current withstand test: 100 kA of 10/350µs

waveform(Ageing & Electrical test ) conducted in a sequence manner & tested in

the Govt. accredited Third party laboratory to meet the requirements of IS/IEC

SITC of 14.2 mm dia 3 mtr long Earth electrode of High tensile steel electrode

with 250 micron copper bonding & 1 bag of Carbon fill Based environment

friendly backfill tested as per IEC 62561-7 in NABL accredited Laboratory and Rupees Five Thousand

233 2.00 suitable stainless Steel double sided clamp. Eco Friendly rust proof heavy duty 5,992.33 Nine Hundred NinetyTwo

weather proof Polyethylene Earth Pit Chamber with following dimensions :254 Paise ThirtyThree Only

mm dia (top), 330 mm dia (bottom) & 260 mm (height).

Split Air - Conditioners : Providing and erecting Inverter based approved make

split air-conditioning unit consisting of condensing unit with variable speed fan

motor, inverter type hermetically sealed rotary compressor with accessories etc.

duly connected separately erected evaporating unit and blower motor with its

accessories by means of extra supplied proper insulated copper tubing,drain PVC Rupees FiftyFive Thousand

234 2.00 pipes suitable for ( cost includes Eco Friendly green gas charging and 15A plug top 55,189.43 Ea. One Hundred EightyNine

& Remote Control & MS Stand) with necessary core cutting. Paise FourtyThree Only

(2) For ISEER Range (KWH/KWH)(4.0 to 4.49)

(B) for 1.5 ton capacity- Premium Cat.

Providing and erecting Inverter based approved make split air-conditioning unit

consisting of condensing unit with variable speed fan motor, inverter type

hermetically sealed rotary compressor with accessories etc. duly connected

separately erected evaporating unit and blower motor with its accessories by Rupees SeventyTwo

means of extra supplied proper insulated copper tubing,drain PVC pipes suitable Thousand Three Hundred

for ( cost includes Eco Friendly green gas charging and 15A plug top & Remote EightyOne Paise SixtyFive

Control & MS Stand) with necessary core cutting. Only

(2) For ISEER Range (KWH/KWH)(4.0 to 4.49)

(C) for 1.7 to 2 ton capacity-Premium Cat.

Water Coolers : Providing and erecting water cooler having storage capacity

25Ltr. & cooling capacity 10 Ltr.per hour @ an ambient temp of 45˚ C. The outlet

temp. of the water should drop by 15˚ C within a hour, The water cooler should

Rupees TwentySeven

be comprising of hermetically sealed compressor, fan motor, condensing unit,

236 2.00 27,270.00 Ea. Thousand Two Hundred

water tank surrounded by evaporating coil, thermostats, relay etc. complete with

necessary inlet & outlet connection. The body of water cooler will be made from

Stainless Steel.

Supplying & erecting 5 stage single reverse osmosis water purification system

with M.S. powder coated frame, prefilter housing with 'O' ring presediment filter

GAC filter, carbon filter suitable buster DC pump capacity 80 psi, mention with 40 Rupees Fifteen Thousand

237 2.00 psi inline type post carbon filter auto low & high pressure switches with following 15,620.66 Ea. Six Hundred Twenty Paise

size of storage tank & LPH capacity & erected as directed SixtySix Only

[B] 25 Ltr / Hr with 30 Ltr. Storage Tank

LIASONING WORK : Providing Power Connection Requirement of 80 KW

Including Electrical Connect Power Charges , Inspector Approval . Liaisoning work Rupees Eighty Thousand

for additional load for requirement, electrical power connection charges Eight Hundred Only

and inspector approval for power

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

SUB EST-03 (Electrical Work)

DATA & NETWORKING :

Rupees Two Hundred

SITC of ABS back box

239 10.00 294.92 Ea NinetyFour Paise

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ]

SITC of Face Plate - Single (Keystone Jack,square)

Rupees Ninety Paise

240 10.00 [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 90.90 Ea

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size

complete to be erected on/in wall or ceiling erected with necessary PVC fittings &

Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, Rupees ThirtyThree Paise

in approved manner as directed ThirtyThree Only

SITC of CAT6 UTP 23AWG Solid: Per Meter

Rupees FourtyThree Paise

242 187.00 [Approved by Competent Authority i.e. not Below the rank of Executive Engineer 43.43 Mtr.

FourtyThree Only

Supply, installation, testing, and commissioning (SITC) of a 24U, 19-inch standard

floor-mount rack. The rack must be made of mild steel with a powder-coated

finish and include lockable front and rear doors (front door typically glass or Rupees Twenty Thousand

perforated, rear door perforated), lockable and removable side panels, and a Two Hundred Only

welded frame construction for stability.

Supply, Installation, Testing, and Commissioning (SITC) oF 1U horizontal cable

manager for a 19-inch rack, made of powder-coated steel with a black finish. The

manager shall feature multiple D-rings, typically 5 to 7, to provide organized Rupees Two Hundred

244 1.00 routing and support for patch cables. The design should facilitate easy moves, 282.80 Ea EightyTwo Paise Eighty

adds, and changes while maintaining proper cable bend radius. Includes all Only

necessary M6 cage nuts and screws for mounting.

SITC of PIGTAIL LC SM SIMPLEX LENGTH- 1m Rupees Seven Hundred

245 10.00 [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 779.72 Ea SeventyNine Paise

SeventyTwo Only

SITC of Patch Panel Cat 6 UTP Keystone Type- 24 Port-Fully Loaded Rupees Four Thousand

246 1.00 [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 4,400.57 Ea Four Hundred Paise

FiftySeven Only

Supply, installation, and commissioning of a 24-Port 10/100/1000 Mbps Layer

Managed Gigabit Switch with 2 SFP uplink ports, suitable for standard 19” rack

mounting. The switch shall support VLAN, QoS, STP/RSTP/MSTP, SNMP, and have

Rupees TwentyThree

a minimum switching capacity of 56 Gbps. It must include all necessary

247 1.00 23,048.19 Ea Thousand FourtyEight Paise

accessories (mounting kit, power cord, etc.), be UL/CE/FCC Class A certified, and

have an internal power supply. Scope includes delivery, rack installation,

configuration, testing, and documentation. Minimum 3-year OEM warranty

SITC of PATCH CORD LC-LC SM DUPLEX LENGTH- 3m Rupees One Thousand

248 2.00 [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 1,901.83 Ea Nine Hundred One Paise

EightyThree Only

Supply, installation, and configuration of a compact firewall device suitable for Rupees EightyFive

securing the network. The firewall shall provide essential security features Thousand Two Hundred

including stateful packet inspection, basic intrusion prevention, URL filtering, and FourtyFour Only

VPN support for secure remote access. It must efficiently handle the expected

network traffic without impacting performance and support multiple user profiles

and security zones. The scope includes delivery, physical installation, integration

with existing network infrastructure, configuration according to library security

policies, testing, and commissioning. Training for basic operation and

administration shall be provided. The device shall come with a minimum one-year

warranty and technical support from the OEM.

Supply, installation, testing, and commissioning of complete Wi-Fi system

including wireless access points (indoor/outdoor as specified), wireless

controllers, network switches, structured cabling, mounting accessories, PoE

injectors or PoE switches as required, configuration, integration with existing LAN

infrastructure, and provisioning for seamless wireless connectivity throughout the

designated area. The system shall support the latest Wi-Fi standards (minimum

Wi-Fi 6 / 802.11ax), ensure high-speed internet access, robust security protocols Rupees Sixty Thousand

250 2.00 (WPA3), centralized management, load balancing, roaming capabilities, and 60,599.99 Ea Five Hundred NinetyNine

scalability for future expansion. All equipment shall be from approved makes, Paise NinetyNine Only

compliant with relevant industry standards, and installed as per manufacturer’s

guidelines and project specifications. The scope includes necessary civil and

electrical works, testing, labeling, documentation, and training to client

personnel, complete in all respects.

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Supply, delivery, installation, testing, and commissioning of a new 75-inch

LED/Smart TV for library or display use. The TV should have a minimum native

resolution of Full HD (1920×1080), with built-in smart functionality (or

compatibility with external streaming devices), at least 2 HDMI ports, USB port(s),

and standard audio output connectivity. It should come with a table stand or wall

Rupees One Lakh

mounting bracket (as required) along with remote, power cable, user manual, and

251 2.00 1,26,250.00 Ea TwentySix Thousand Two

warranty card (minimum 1 year). The supplier shall mount or place the TV at the

Hundred Fifty Only

designated location, ensure it works (inputs, network, picture quality), carry out

necessary cable routing (power, HDMI etc.), and hand over in fully operational

condition with demonstration to staff.

Supply, delivery, and installation of a brand-new desktop computer system

suitable for library operations and basic administrative tasks. The system shall be

equipped with a minimum Intel Core i5 (12th Generation) or AMD Ryzen

processor, 8GB DDR4 RAM (expandable), and a 512GB SSD for fast performance

and storage. It shall include a 21.5-inch Full HD LED monitor, a USB wired

keyboard and optical mouse, and be pre-installed with Windows 11 Professional

(or latest version) with proper activation.

Rupees Fourty Thousand

252 10.00 The system shall also be pre-installed with a genuine, licensed Microsoft Office 40,400.00 Ea

Four Hundred Only

suite (latest version), fully activated and ready for use, including at minimum

Word, Excel, and PowerPoint.

The unit shall support both Ethernet LAN and Wi-Fi (minimum Wi-Fi 5), and

include essential I/O ports such as USB 3.0, HDMI, and audio jacks. The system

shall come with a 3-year on-site warranty and technical support.

Supply and installation of a monochrome laser printer for use in the library for

tasks such as printing borrower slips, overdue notices, reports, and other

documents. The printer should have a minimum print speed of 20 pages per

Rupees TwentyTwo

minute (ppm), a duty cycle of at least 10,000 pages per month, and support USB

253 2.00 22,220.00 Ea Thousand Two Hundred

and/or Wi-Fi connectivity. The printer should come with starter toner, power

cables, driver installation CD (or digital access), and a one-year warranty. Setup

and testing at the library site are to be included.

CCTV : Supply, installation, testing, and commissioning of a 5 MP STQC-certified

dome-type IP CCTV camera with vandal-proof metal housing, secure firmware,

encrypted video transmission, and compliance with MeitY Essential Rupees Thirteen Thousand

Requirements; to be fully integrated, configured, and commissioned as a Six Hundred ThirtyFive Only

complete, operable surveillance unit in accordance with the contract

Supply, installation, testing, and commissioning of a 5 MP STQC-certified

dome-type IP CCTV camera with vandal-proof metal housing, secure firmware,

encrypted video transmission, and compliance with MeitY Essential Rupees Fifteen Thousand

Requirements; to be fully integrated, configured, and commissioned as a One Hundred Fifty Only

complete, operable surveillance unit in accordance with the contract

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size

complete to be erected on/in wall or ceiling erected with necessary PVC fittings &

Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, Rupees ThirtyThree Paise

in approved manner as directed ThirtyThree Only

SITC of CAT6 UTP 23AWG Solid: Per Meter

Rupees FourtyThree Paise

257 693.00 [Approved by Competent Authority i.e. not Below the rank of Executive Engineer 43.43 Mtr.

FourtyThree Only

SITC of Patch Panel Cat 6 UTP Keystone Type- 24 Port-Fully Loaded Rupees Four Thousand

258 1.00 [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 4,400.57 Ea Four Hundred Paise

FiftySeven Only

Supply, Installation, Testing, and Commissioning (SITC) oF 1U horizontal cable

manager for a 19-inch rack, made of powder-coated steel with a black finish. The

manager shall feature multiple D-rings, typically 5 to 7, to provide organized Rupees Two Hundred

259 1.00 routing and support for patch cables. The design should facilitate easy moves, 282.80 Ea EightyTwo Paise Eighty

adds, and changes while maintaining proper cable bend radius. Includes all Only

necessary M6 cage nuts and screws for mounting.

SITC of PIGTAIL LC SM SIMPLEX LENGTH- 1m Rupees Seven Hundred

260 21.00 [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 779.72 Ea SeventyNine Paise

SeventyTwo Only

SITC of 24 x 10/100/1000BASE-T PoE ports 4 x Gigabit RJ45/SFP Combo

ports Advanced L2 switching and security features L2+ Static Routing Optional Rupees ThirtyOne

261 1.00 “standard mode” or “surveillance mode” management user interface 193 W PoE 31,996.80 Ea Thousand Nine Hundred

budget NinetySix Paise Eighty Only

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

SITC of PATCH CORD LC-LC SM DUPLEX LENGTH- 3m Rupees One Thousand

262 1.00 [Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] 1,901.83 Ea Nine Hundred One Paise

EightyThree Only

Supply and installation of a 24-channel Network Video Recorder (NVR) with

support for up to 8 SATA hard drives and capable of handling video input

resolutions up to 12MP for both live preview and playback. The NVR shall support

H.264/H.265 video compression, provide simultaneous multi-channel recording Rupees SixtyFour

263 1.00 and playback, and feature user-friendly interface for remote monitoring via web 64,502.64 Ea Thousand Five Hundred

and mobile apps. It must include advanced functionalities such as motion Two Paise SixtyFour Only

detection, alarm management, and network redundancy options. The unit shall

support PoE ports (if applicable) and be compatible with standard IP cameras.

Supply and installation of 6TB Surveillance-grade Hard Disk Drive (HDD) suitable

for continuous 24x7 operation in CCTV/DVR/NVR systems. The HDD shall be

specifically designed for video surveillance applications with enhanced reliability,

high write endurance, and optimized for multiple HD video stream recording. It

must support SATA III interface (6 Gbps), have a minimum spindle speed of 5400 Rupees Fifteen Thousand

264 2.00 RPM or higher, and include vibration resistance and thermal management 15,806.50 Ea Eight Hundred Six Paise

features. Scope includes delivery, integration with existing recording system Fifty Only

(DVR/NVR), formatting, testing, and ensuring proper recording functionality. HDD

must be from a reputed brand

Supply, Installation, Testing, and Commissioning (SITC) of a comprehensive, multi-

year e-book subscription license. This includes the Supply of a robust digital

library platform, providing unlimited access for the specified number of users to a

diverse collection of educational and academic titles, with a significant corpus of

content available in both English and Gujarati. The supplier will also manage the

complete Installation and setup of the platform, ensuring full integration and

interoperability across various devices, including desktops, mobile devices (iOS

and Android), and the NAMO E-Tab application. Post-installation, the bidder must

perform thorough Testing to verify platform functionality, including seamless user Rupees Sixteen Thousand

access, reliable content delivery, compliance with all digital rights management Six Hundred SixtyFive Only

(DRM) policies, and adherence to the tender's technical specifications. Finally, the

successful commissioning involves providing necessary training to authorized

personnel and the official handover of the fully operational system, backed by a

Comprehensive Annual Maintenance Contract (CAMC) covering all updates,

technical support, and operational issues for the duration of the contract.

PA SYSTEM : Supplying and erecting ceiling speaker with rated power of

watt/power tapping 30/15/7.5 watt available,opening angle 180 degree H *

degree V ,sound pressure level 88 dB ,frequency response of 70Hz to 20KHz Rupees One Thousand Two

[Approved by Competent Authority i.e. not Below the rank of Executive Engineer ] Hundred Twelve Only

SITC of 16 Zone Standaone Voice Alarm controller 19” 2U rack mount type with Rupees One Lakh

Built in Media Player with USB (MP3/ WAV/FLAC), Bluetooth V5.0, FM Radio FourtyThree Thousand

functions, SD CARD , Pre-recorded Evacuation messages and fire alarm Three Hundred SixtyNine

integration supported Paise FourtyNine Only

Supply and installation of a Voice Alarm Call Station designed for emergency

communication and public address in safety and security systems. The call station

shall support clear two-way voice communication, with built-in microphone and

speaker, and include features such as call initiation, emergency signaling, and Rupees FourtyTwo

268 1.00 integration capability with existing voice alarm or public address systems. It 42,561.40 Ea Thousand Five Hundred

should be rugged, wall-mountable, and compliant with relevant safety standards. SixtyOne Paise Fourty Only

Scope includes delivery, installation, wiring, integration with the alarm control

system, functional testing, and commissioning. The product must carry a

minimum one-year OEM warranty.

Supplying , installing & testing approved make Microphone for Speech, Music, &

Close to lip singing with inbuilt protection against breath & wind noise with

capability to capture sound from long distance & wide area with frequency

Rupees Two Thousand Six

response 50 - 16000 Hz, having sensitivity 1.8mv / Pa & impedance 430 ohms(Lo -

269 2.00 2,654.28 Ea Hundred FiftyFour Paise

Z) supplied with quick detachable holder, 6 Mtr long. Twin core cable & 3 pin XLR

TwentyEight Only

connector. [[Approved by Competent Authority i.e. not Below the rank of

Executive Engineer ]

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Supplying & erecting Amplifier having following specification:

Power Output :100 W (RMS):(130 W Max.)

inputs :5 Mics & 2 Aux.

frequency Response :50-15000 Hz+3db

Tone Controls :Cut & Boost type Rupees Six Thousand Two

270 1.00 Speaker Matching :4-8-ohms 70- 100 V line 6,249.88 Ea Hundred FourtyNine Paise

LED Meter :5 LED Array. EightyEight Only

The amplifier suitable to operate 240V A.C.& 24 volt D.C. (Battery) with

automatic changeover from AC to Battery operation, duly protected by wrong

Battery Polarity connection. [[Approved by Competent Authority i.e. not Below

the rank of Executive Engineer ]

Providing and erecting ISI mark Medium class RIGID PVC PIPES of following size

complete to be erected on/in wall or ceiling erected with necessary PVC fittings &

Junction boxes fixed with adhesive solution & Clamps with following dia of pipes, Rupees ThirtyThree Paise

in approved manner as directed ThirtyThree Only

Supply, Installation, Testing, and Commissioning (SITC) of: High-quality, low-

impedance, 2-core, 1.5 sqmm speaker cable for the connection of loudspeakers

to the voice alarm amplifier/controller. The cable must be suitable for both Rupees TwentyTwo Paise

normal public address and emergency voice alarm applications, ensuring clear and TwentyTwo Only

reliable audio signal transmission

SUB EST-04 (ELV Work)

Electric Motor Driven Hydrant Pump

I) Supplying,Installing, testing and commissioning of Fire authority approved

Electrical driven fire pump suitable for automatic/ manual operation consisting of

the following-Rates for erection of pump only Horizontal split casing, high

pressure, single/ multistage centrifugal type fire pump having cast iron body,

bronze impeller,stainless steel shaft & capable of delivering 1280 LPM against a

total head of 40Mtr while running at 2900 RPM complete with proper connection

to suction and delivery line, and including bypass arrangement for testing of

pumps as per the requirement. Suitable mechanical seal with mounting

aggangement shall be included, having a name plate indicating suction, delivery,

head, discharge, stages, RPM and direction of rotation. Y Stainers at pump input

shall be provided as per manufacturer requirements. Pump shall be capable of

furnishing not less than 150% of rated capacity at a head not less than 65 % of Rupees One Lakh ThirtySix

273 1.00 rated head. The shut off head shall not exceed 120% of rated head. 1,36,350.00 Set Thousand Three Hundred

II) Squirrel cage, induction motor, TEFC type suitable for 415 + 10%V, 3 phase, 50 Fifty Only

Hz, AC supply, of suitable HP rating for the above pump with synchronous speed

of 2900 RPM conforming to IP 55 protection & class 'F' insulation. The motor

shall conform to IS 325 1978 (up to date) with flexible coupling and coupling

III) Factory Fabricated Common base plate for mounting pump and motor

fabricated of mild steel channel as per manufacturer's recommendation with

heavy duty Anti Vibration pads (4 Nos., heavy duty). Grouting bolts to be provided

and installed by vendor at his cost

IV) Flexible Coupling and coupling guard for direct coupling of pump and motor.

v) Drain Pipe with Valve

Discharge : 1280 LPM

Pumping Head : 40 M

Pump Size : 30 HP

vii) Rate should included interconnection cables and Cable box if reqd for cable

conn. to motor.

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Electrical Motor Driven Jockey Pump For Hydrant & Sprinkler System

Supplying,Installing, testing & commissioning of fire authority approved

electrically driven Jockey pump suitable for automatic/manual operation

consisting of the following:

I) Horizontal / Vertical mounted multistage jockey pump having cast iron body,

S.S. impeller, stainless shaft with mechanical seal capable of delivering 1280 LPM

against total head of 40Mtr while running at 2900 RPM complete. The system

shall be complete with necessary pressure gauge with gun metal shut off cock on

delivery side including bypass arrangement for testing of working of the pumping

set as required. The pump should meet the requirement of IS 15105:2002 and

must be approved by the local fire authority. Y-Stainers at pump input shall be Rupees SeventyTwo

274 1.00 provided as per manufacturer requirements. 72,720.00 Set Thousand Seven Hundred

II) Squirrel cage induction motor suitable for 415 + 10%V, 3 phase, 50 Hz, AC Twenty Only

supply of suitable HP rating for the above pump with synchronous speed of

RPM T.E.F.C type connected to pump with flexible coupling and coupling guard .

III) Factory fabricated Common base plate for mounting pump and motor

fabricated of mild steel channel as per manufacturer's recommendation with

heavy duty 4 Nos. Anti Vibration pads.(Cushy foot) . grouting bolts to be provided

and installed by the vendor at his cost

IV) Suitable reinforced cement concrete pump foundations as per manufacturer's

design including foundation bolts, washers as required.

v) Drain pipe with valve (25 mm dia)

Discharge : 1280 LPM

Pumping Head : 40 M

Pump Size : 10 HP

vii) Rate shall include inter connecting cables and cable box if reqd for cable conn

Diesel Fire Pump

Supplying, Installation, Testing and commissioning of Diesel engine driven fire

pump suitable for automatic operation and consisting of following: Horizontal

type, centrifugal End Suction pump of cast iron body & bronze impeller

mechanical seal to ensure a minimum pressure of 3.5 kg / sq.cm. at highest and

farthest outlet at specified flow of 137 m3/Hour@ 40M. head conforming to IS Rupees Three Lakh

275 1.00 1520. with M.S.fabricated common base plate, coupling, coupling guard, 3,48,450.00 Set FourtyEight Thousand Four

foundation bolts etc. as required Hundred Fifty Only

Diesel Fire Pump

Discharge : 1280 LPM

Pumping Head : 40 M

Pump Size : 30 HP

Fire pump panel (Combined for All Pumps) and electrical works - Starter panel

with star delta or as per CFO approved starters rated to suite pump HP with

necessary protection feautres like SPP / ELR / OL / SC / phase and on off indicating

lamps. The busbars shall be of Al - 0.8 A / sq mm size. Panel shall be fabricated

from 14G sheet steel with seven tank process powder coated and shall be min IP

52. Panel shall have Ammeter / Voltmeter and KWh meter. Cabling / earthing

from panel to pump shall be scope of vendor without any extra cost. Cabling -

supply / laying and terminating, shall be Al XLPE armoured / Cu XLPE armoured /

Rupees Two Lakh

as per manufacturers specifications with necessary terminal box to terminate the

276 1.00 2,22,200.00 Each TwentyTwo Thousand Two

cables. Panel shall be rated min for 25KA fault level. Cable trays - hot dip GI

ladder type 16 gauge with required supports shall be used for cabling. Panel shall

have one incomer MCCB / ACB of required rating where by incoming supply and

earthing shall be terminated by electrical contractor.Starters shall be suitable for

respective motors.panel to take inputs from pressure switch/on-off switch . Flow

switch wiring shall be in suitable mms pvc consuits. Panel should be

manufactured by CPRI approved panel builder

Supply, Installation, testing and commissioning of CAST IRON Y-TYPE STRAINER

Rupees Fifteen Thousand

(flanged) PN-1.6 ; body - C.I., Screen stainless steel 150 mm dia

277 1.00 15,326.75 Each Three Hundred TwentySix

Paise SeventyFive Only

Supplying,Installing, testing & commissioning of dial type Pressure Guage having Rupees Two Thousand One

278 3.00 100 mm dial & range of 0-15 Kg/cm2 with syphon and cock. 2,151.30 Each Hundred FiftyOne Paise

Supplying,Installing, testing & commissioning of Pressure Switch required Rupees Two Thousand

accessories Twenty Only

Supply, installation, testing and commissioning of butterfly valve PN 1.6, with s.s

Rupees Four Thousand

seat duly lSI marked complete with Nuts, Bolts, washers, gaskets, confirming to IS

280 1.00 4,848.00 Each Eight Hundred FourtyEight

13095, of following sizes as required. 150 mm dia

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Supply, installation, testing and commissioning of butterfly valve PN 1.6, with s.s

Rupees Three Thousand

seat duly lSI marked complete with Nuts, Bolts, washers, gaskets, confirming to IS

281 2.00 3,838.00 Each Eight Hundred ThirtyEight

13095, of following sizes as required. 80 mm dia

Supply, installation, testing and commissioning of butterfly valve PN 1.6, with s.s

Rupees Three Thousand

seat duly lSI marked complete with Nuts, Bolts, washers, gaskets, confirming to IS

282 1.00 3,838.00 Each Eight Hundred ThirtyEight

13095, of following sizes as required. 50 mm dia

Supplying,Installing, testing & commissioning of CI dual plate non-return valve of

Rupees Five Thousand Two

283 1.00 following sizes conforming to IS: 5312 complete with rubber gasket, GI bolts, nuts, 5,252.00 Each

Hundred FiftyTwo Only

washers etc. as required. 150 mm dia.

Supply, Installation, Testing and Commissioning of the following sizes of flange

jointed / screwed / welded, M.S. Pipes of Class C (Medium class) ISI marked

including accessories such as MS bracket, U clamps with Anchor fasteners, tees /

Rupees One Thousand

elbows / reducers / couplings / unions / bends / flanges etc., and laying on the

284 125.00 1,424.10 Mtr Four Hundred TwentyFour

surface including painting with two coats of anticorrosive primer and two coats of

approved red enamel paint after laying and testing after Installation etc. as per

specifications complete as required. 150 mm

Supply, Installation, Testing and Commissioning of the following sizes of flange

jointed / screwed / welded, M.S. Pipes of Class C (Medium class) ISI marked

including accessories such as MS bracket, U clamps with Anchor fasteners, tees /

Rupees One Thousand Two

elbows / reducers / couplings / unions / bends / flanges etc., and laying on the

285 14.00 1,232.20 Mtr Hundred ThirtyTwo Paise

surface including painting with two coats of anticorrosive primer and two coats of

approved red enamel paint after laying and testing after Installation etc. as per

specifications complete as required. 100 mm

Supply, Installation, Testing and Commissioning of the following sizes of flange

jointed / screwed / welded, M.S. Pipes of Class C (Medium class) ISI marked

including accessories such as MS bracket, U clamps with Anchor fasteners, tees /

Rupees Nine Hundred

elbows / reducers / couplings / unions / bends / flanges etc., and laying on the

286 23.00 949.40 Mtr FourtyNine Paise Fourty

surface including painting with two coats of anticorrosive primer and two coats of

approved red enamel paint after laying and testing after Installation etc. as per

specifications complete as required. 80 mm

Supply, Installation, Testing and Commissioning of the following sizes of flange

jointed / screwed / welded, M.S. Pipes of Class C (Medium class) ISI marked

including accessories such as MS bracket, U clamps with Anchor fasteners, tees /

elbows / reducers / couplings / unions / bends / flanges etc., and laying on the Rupees Seven Hundred

surface including painting with two coats of anticorrosive primer and two coats of Seventeen Paise Ten Only

approved red enamel paint after laying and testing after Installation etc. as per

specifications complete as required. 65 mm

Supply, Installation, Testing and Commissioning of the following sizes of flange

jointed / screwed / welded, M.S. Pipes of Class C (Medium class) ISI marked

including accessories such as MS bracket, U clamps with Anchor fasteners, tees /

Rupees Five Hundred

elbows / reducers / couplings / unions / bends / flanges etc., and laying on the

288 30.00 585.80 Mtr EightyFive Paise Eighty

surface including painting with two coats of anticorrosive primer and two coats of

approved red enamel paint after laying and testing after Installation etc. as per

specifications complete as required. 50 mm

Supply, Installation, Testing and Commissioning of the following sizes of flange

jointed / screwed / welded, M.S. Pipes of Class C (Medium class) ISI marked

including accessories such as MS bracket, U clamps with Anchor fasteners, tees /

Rupees Four Hundred

elbows / reducers / couplings / unions / bends / flanges etc., and laying on the

289 30.00 494.90 Mtr NinetyFour Paise Ninety

surface including painting with two coats of anticorrosive primer and two coats of

approved red enamel paint after laying and testing after Installation etc. as per

specifications complete as required. 40 mm

Supply, Installation, Testing and Commissioning of the following sizes of flange

jointed / screwed / welded, M.S. Pipes of Class C (Medium class) ISI marked

including accessories such as MS bracket, U clamps with Anchor fasteners, tees /

Rupees Four Hundred

elbows / reducers / couplings / unions / bends / flanges etc., and laying on the

290 20.00 449.45 Mtr FourtyNine Paise

surface including painting with two coats of anticorrosive primer and two coats of

FourtyFive Only

approved red enamel paint after laying and testing after Installation etc. as per

specifications complete as required. 32 mm

Supply, Installation, Testing and Commissioning of the following sizes of flange

jointed / screwed / welded, M.S. Pipes of Class C (Medium class) ISI marked

including accessories such as MS bracket, U clamps with Anchor fasteners, tees /

elbows / reducers / couplings / unions / bends / flanges etc., and laying on the Rupees Two Hundred

surface including painting with two coats of anticorrosive primer and two coats of FiftyTwo Paise Fifty Only

approved red enamel paint after laying and testing after Installation etc. as per

specifications complete as required. 25 mm

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Supplying,Installing, testing & commissioning of Weather proof standard fire hose

cabinet (750 mm x 600 mm x 300 mm deep) made out of 16 SWG powder coated

M.S. sheet having single or double opening glazed (4.0 mm thick glass) shutter

including necessary locking arrangement by allen key, stove enamelled Fire red Rupees Five Thousand One

finish (as per IS : 5, shade no. 536) with " Fire Hose" marked on front, suitable for Hundred FiftyOne Only

housing 2 nos. 15m long 63 mm dia Hose pipe, 1 No. branch pipe & nozzle

spanner (For External Hydrant).

Supply, Installation, Testing and Commissioning of Weather proof Standard Fire

Hose Cabinet wall mounting type (450 mm x 600 mm x 250 mm deep) having Rupees One Thousand

293 4.00 single or double opening with necessary locking arrangement by allan key suitable 1,818.00 Each Eight Hundred Eighteen

for housing 1 nos. hose pipe, 1 no. Branch pipe & nozzle spanner. Only

Supply ,installation, testing and commissioning S.S. Single Headed Fire Hydrant

Valve with 80mm N.B. flanged inlet, 63 mm dia female instantaneous outlet type.

S.S. coupling, blankcap, chain, twist release type lug & all accessories Conforming Rupees Three Thousand

to IS:5290. Including fixing with supports, flanged tapping from wet riser,orifice Thirty Only

plate complete as required by the Local Fire Authority.

Supply, installation, testing and commissioning non-percolating rubber reinforced Rupees Three Thousand

295 6.00 lined fire Hose pipe (as per IS:903) of 63 mm dia and 15 mtrs long. 3,232.00 Each Two Hundred ThirtyTwo

Supply, Installation, Testing and commissioning of 63 mm dia instantaneous Rupees Eight Hundred

pattern aluminium short branch pipe Eight Only

Supply, installation, testing and commissioning of First Aid Hose Reel equipment

conforming to IS:884 comprising of hose reel drum, 8 mm shut off nozzle, Rubber

Rupees Four Thousand

hose reel tubing as per IS: 444 of 25 mm dia x 45 mtr. long, painting, Manual fix

297 6.00 4,141.00 Each One Hundred FourtyOne

type with fixing bracket, anchor fastener, bolts & nuts etc. complete as required

by Local Fire Authority.

Supply, installation, testing and commissioning of SS Ball Valve. Rupees Eight Hundred

(a) 25mm dia Eight Only

Supply, installation, testing and commissioning of Cast lron Four Way Fire Brigade

Rupees Four Thousand

Inlet as per IS:904 having 63 mm dia inlet with blank cap and chain with

299 1.00 4,848.00 Each Eight Hundred FourtyEight

necessary fittings, flanges, nut bolts etc. complete as required.

Supply, Installation, Testing and Commissioning of Gun Metal Air Release Valve Rupees Three Thousand

300 1.00 with necessary fittings. Size: 25 mm (For Riser) 3,535.00 Each Five Hundred ThirtyFive

Supply, Installation, Testing and commissioning of Quartzoid Bulb type Sprinkler

Rupees Three Hundred

301 71.00 Heads. 353.50 Each

FiftyThree Paise Fifty Only

(a) Pendent Sprinkler 57°C - standard response

Supply, installation, testing and commissioning of ABC type Fire Extinguisher of

Rupees One Thousand

6.0 kg confirm to IS:15683, with ISI marked / TAC approved fitted with required

302 4.00 1,424.10 Each Four Hundred TwentyFour

accessories including wall suspension brackets.

Supply, installation, testing and commissioning of Carbon Dioxide (Co2) type Fire

Rupees Three Thousand

Extinguisher of 4.5 kg confirm to IS:15683, with ISI marked / TAC approved fitted

303 4.00 3,838.00 Each Eight Hundred ThirtyEight

with required accessories including wall suspension brackets.

Supplying,Installing, testing & commissioning of fire alarm and pump trigger

Rupees Six Hundred Six

304 4.00 system as per requirement and specification consisting of following items Manual 606.00 Each

Supplying,Installing, testing & commissioning of fire alarm and pump trigger

Rupees Seven Hundred

305 4.00 system as per requirement and specification consisting of following items Hooters 757.50 Each

FiftySeven Paise Fifty Only

Supplying,Installing, testing & commissioning of fire alarm and pump trigger

Rupees Five Hundred Five

306 4.00 system as per requirement and specification consisting of following items Pump 505.00 Each

On / Off switch:

Supplying,Installing, testing & commissioning of fire alarm and pump trigger

system as per requirement and specification consisting of following items 4 core Rupees Thirty Paise Thirty

1.5 sq.mm cu. Flexible wire with pvc pipe & hardware for pump on/off switch Only

Supplying,Installing, testing & commissioning of fire alarm and pump trigger

system as per requirement and specification consisting of following items 2 core Rupees Fourty Paise Fourty

1.5 sq.mm cu. Flexible wire with pvc pipe & hardware for pump on/off switch Only

Providing and fixing M.S. structural work fabricated from standard sections, (MS

rounds, angles, channels etc.) including cutting to size, drilling, welding, including

cost of fasteners, clamps in RCC structural members as directed, including two or Rupees One Hundred Six

more coats of synthetic paint over one coat of primer after surface preparation Paise Five Only

including cutting and making good walls (Structural other than pipe supoort).

Painting of above ground lines with two coats of red oxide primer and two coat of Rupees Seven Hundred

sinthetic enamal paint (PO.Red) Seven Only

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Supplying of AUTOGLOW Signages in Block / Small Letters of Specified Sizes: Fire

Rupees Two Hundred

309 2.00 lift size: 4" X 12" 252.50 Each

FiftyTwo Paise Fifty Only

Supplying of AUTOGLOW Signages in Block / Small Letters of Specified Sizes: Fire

Rupees Two Hundred

310 2.00 Hydrant: 4" X 12" 252.50 Each

FiftyTwo Paise Fifty Only

Supplying of AUTOGLOW Signages in Block / Small Letters of Specified Sizes:

Rupees One Hundred

311 2.00 "DCP" Extinguisher: 8" X 4" 151.50 Each

FiftyOne Paise Fifty Only

Supplying of AUTOGLOW Signages in Block / Small Letters of Specified Sizes:

Rupees One Hundred

312 2.00 "CO2" Extinguisher: 8" x 4" 151.50 Each

FiftyOne Paise Fifty Only

Supplying of AUTOGLOW Signages in Block / Small Letters of Specified Sizes: In

Rupees Three Hundred

313 2.00 case of Fire, do not use lift, use staircase: 8" x 8" 353.50 Each

FiftyThree Paise Fifty Only

SUB EST-05 (Fire Fighting Work )

Providing and fixing, in proper line and level (with necessary support like, brick

masonry pedestals and battens, if necessary) to floor, approved quality, heavy

duty, White UPVC-Schedule 40 Grade as per ASTM D-1785, of Astral or

equivalent, Open & Conceal piping, complete, including jointing with rubbering

and airtight joints, with necessary specials, couplers, elbow, equal tees, tail piece, Rupees SeventyTwo Paise

adapter (both male and female), reducer (single stage, double stage and triple SixtyFive Only

stage), end cap, fabricated bend, etc., and lubricant or jointing material, including

testing, cutting, making good the wall, ceiling and floor etc. Testing & installation

of pipe lines as per drawing & specification. 15 mm

Providing and fixing, in proper line and level (with necessary support like, brick

masonry pedestals and battens, if necessary) to floor, approved quality, heavy

duty, White UPVC-Schedule 40 Grade as per ASTM D-1785, of Astral or

equivalent, Open & Conceal piping, complete, including jointing with rubbering

and airtight joints, with necessary specials, couplers, elbow, equal tees, tail piece, Rupees One Hundred

315 143.00 adapter (both male and female), reducer (single stage, double stage and triple 198.97 Rmt NinetyEight Paise

stage), end cap, fabricated bend, etc., and lubricant or jointing material, including NinetySeven Only

testing, cutting, making good the wall, ceiling and floor etc. Testing & installation

of pipe lines as per drawing & specification. 20 mm

Providing and fixing, in proper line and level (with necessary support like, brick

masonry pedestals and battens, if necessary) to floor, approved quality, heavy

duty, White UPVC-Schedule 40 Grade as per ASTM D-1785, of Astral or

equivalent, Open & Conceal piping, complete, including jointing with rubbering

and airtight joints, with necessary specials, couplers, elbow, equal tees, tail piece,

Rupees NinetyOne Paise

316 220.00 adapter (both male and female), reducer (single stage, double stage and triple 91.84 Rmt

EightyFour Only

stage), end cap, fabricated bend, etc., and lubricant or jointing material, including

testing, cutting, making good the wall, ceiling and floor etc. Testing & installation

of pipe lines as per drawing & specification. 25 mm

Providing and fixing, in proper line and level (with necessary support like, brick

masonry pedestals and battens, if necessary) to floor, approved quality, heavy

duty, White UPVC-Schedule 40 Grade as per ASTM D-1785, of Astral or

equivalent, Open & Conceal piping, complete, including jointing with rubbering

and airtight joints, with necessary specials, couplers, elbow, equal tees, tail piece,

Rupees One Hundred

317 380.00 adapter (both male and female), reducer (single stage, double stage and triple 119.15 Rmt

Nineteen Paise Fifteen Only

stage), end cap, fabricated bend, etc., and lubricant or jointing material, including

testing, cutting, making good the wall, ceiling and floor etc. Testing & installation

of pipe lines as per drawing & specification. 32 mm

Providing and fixing, in proper line and level (with necessary support like, brick

masonry pedestals and battens, if necessary) to floor, approved quality, heavy

duty, White UPVC-Schedule 40 Grade as per ASTM D-1785, of Astral or

equivalent, Open & Conceal piping, complete, including jointing with rubbering

and airtight joints, with necessary specials, couplers, elbow, equal tees, tail piece, Rupees One Hundred

318 99.00 adapter (both male and female), reducer (single stage, double stage and triple 148.12 Rmt FourtyEight Paise Twelve

stage), end cap, fabricated bend, etc., and lubricant or jointing material, including Only

testing, cutting, making good the wall, ceiling and floor etc. Testing & installation

of pipe lines as per drawing & specification. 40 mm

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Providing and fixing, in proper line and level (with necessary support like, brick

masonry pedestals and battens, if necessary) to floor, approved quality, heavy

duty, White UPVC-Schedule 40 Grade as per ASTM D-1785, of Astral or

equivalent, Open & Conceal piping, complete, including jointing with rubbering

and airtight joints, with necessary specials, couplers, elbow, equal tees, tail piece, Rupees One Hundred

319 44.00 adapter (both male and female), reducer (single stage, double stage and triple 195.67 Rmt NinetyFive Paise SixtySeven

stage), end cap, fabricated bend, etc., and lubricant or jointing material, including Only

testing, cutting, making good the wall, ceiling and floor etc. Testing & installation

of pipe lines as per drawing & specification. 50 mm

Providing and fixing concealed center point to wall ceiling & floor CPVC (SDR

13.5) PIPE having National Sanitation Foundation (NSF) seal for potable water of

Rupees Two Hundred Eight

320 44.00 following dia. nominal bore tube fittings and clamps including making good the 208.80 Rmt

Paise Eighty Only

wall, ceiling and floor etc. complete. All Conceal Pipe line Cold & Hot Water &

Providing, fixing, jointing and testing, heavy quality cast bronze / brass BALL

VALVE / OR WHEEL valves of approved make, including flanges / unions, nuts,

Rupees Nine Hundred Nine

321 8.00 bolts, washers, etc. complete, as approved by the Architect and Engineer-in- 909.00 Nos

charge for water supply lines of the following Nominal bore (NB) size: 15mm

Providing, fixing, jointing and testing, heavy quality cast bronze / brass BALL

VALVE / OR WHEEL valves of approved make, including flanges / unions, nuts,

Rupees One Thousand Two

322 8.00 bolts, washers, etc. complete, as approved by the Architect and Engineer-in- 1,212.00 Nos

Hundred Twelve Only

charge for water supply lines of the following Nominal bore (NB) size: 20mm

Providing, fixing, jointing and testing, heavy quality cast bronze / brass BALL

VALVE / OR WHEEL valves of approved make, including flanges / unions, nuts, Rupees One Thousand

323 8.00 bolts, washers, etc. complete, as approved by the Architect and Engineer-in- 1,818.00 Nos Eight Hundred Eighteen

charge for water supply lines of the following Nominal bore (NB) size: 25mm Only

Providing, fixing, jointing and testing, heavy quality cast bronze / brass BALL

Rupees Two Thousand

VALVE / OR WHEEL valves of approved make, including flanges / unions, nuts,

324 9.00 bolts, washers, etc. complete, as approved by the Architect and Engineer-in- 2,777.50 Nos

SeventySeven Paise Fifty

charge for water supply lines of the following Nominal bore (NB) size: 32mm

Providing, fixing, jointing and testing, heavy quality cast bronze / brass BALL

VALVE / OR WHEEL valves of approved make, including flanges / unions, nuts, Rupees Three Thousand

325 9.00 bolts, washers, etc. complete, as approved by the Architect and Engineer-in- 3,595.60 Nos Five Hundred NinetyFive

charge for water supply lines of the following Nominal bore (NB) size: 40mm Paise Sixty Only

Providing, fixing, jointing and testing, heavy quality cast bronze / brass BALL

VALVE / OR WHEEL valves of approved make, including flanges / unions, nuts, Rupees Four Thousand

326 6.00 bolts, washers, etc. complete, as approved by the Architect and Engineer-in- 4,898.50 Nos Eight Hundred NinetyEight

charge for water supply lines of the following Nominal bore (NB) size: 50mm Paise Fifty Only

Providing, fixing, jointing and testing, heavy Quality Gun metal or brass Non

return valve confirming to IS 778, with screwed / flanged ends, 20 Kg/m2 of Rupees Two Thousand Five

approved make, on water supply lines of the following Nominal bore (NB) size: Hundred TwentyFive Only

INTERNAL DRAINAGE

Providing and fixing Approved SWR Type B quality, heavy duty, UPVC pipes - Ring

Fit & Self Fit, Supreme or equivalent make, Confirming to IS 13592 & Fitting

confirming to IS 14735 for waste water or soil waste pipe, with necessary specials,

bends, such as `Y' junction, `T' junction (both single and double), including plugs,

shoes, cowls, flange compression type fittings, wall clips, in proper line and level

Rupees Eight Hundred

with necessary support like brackets/clamps, clips, RCC or brick pedestals or

328 83.00 834.38 Rmt ThirtyFour Paise ThirtyEight

battens, if necessary, to wall, ceiling and floor, open or concealed complete

jointing with rubberising and airtight joints, with ‘T’ shaped rubber ring, etc., and

lubricant or jointing material, including testing, cutting, making good the wall,

ceiling and floor, etc. Testing & installation of pipe lines as per drawing &

160 mm. (Soil + Waste + Rain Water) - Type B

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

Providing and fixing Approved SWR Type B quality, heavy duty, UPVC pipes - Ring

Fit & Self Fit, Supreme or equivalent make, Confirming to IS 13592 & Fitting

confirming to IS 14735 for waste water or soil waste pipe, with necessary specials,

bends, such as `Y' junction, `T' junction (both single and double), including plugs,

shoes, cowls, flange compression type fittings, wall clips, in proper line and level

with necessary support like brackets/clamps, clips, RCC or brick pedestals or Rupees Nine Hundred

329 165.00 battens, if necessary, to wall, ceiling and floor, open or concealed complete 918.67 Rmt Eighteen Paise SixtySeven

jointing with rubberising and airtight joints, with ‘T’ shaped rubber ring, etc., and Only

lubricant or jointing material, including testing, cutting, making good the wall,

ceiling and floor, etc. Testing & installation of pipe lines as per drawing &

110 mm. (Soil + Waste + Rain Water) - Type B

Providing and fixing Approved SWR Type B quality, heavy duty, UPVC pipes - Ring

Fit & Self Fit, Supreme or equivalent make, Confirming to IS 13592 & Fitting

confirming to IS 14735 for waste water or soil waste pipe, with necessary specials,

bends, such as `Y' junction, `T' junction (both single and double), including plugs,

shoes, cowls, flange compression type fittings, wall clips, in proper line and level

with necessary support like brackets/clamps, clips, RCC or brick pedestals or Rupees Two Hundred

330 66.00 battens, if necessary, to wall, ceiling and floor, open or concealed complete 280.23 Rmt Eighty Paise TwentyThree

jointing with rubberising and airtight joints, with ‘T’ shaped rubber ring, etc., and Only

lubricant or jointing material, including testing, cutting, making good the wall,

ceiling and floor, etc. Testing & installation of pipe lines as per drawing &

75 mm. - Balcony + Standing Balcony + AC Drain - PVC 10 KG

Providing and fixing Approved SWR Type B quality, heavy duty, UPVC pipes - Ring

Fit & Self Fit, Supreme or equivalent make, Confirming to IS 13592 & Fitting

confirming to IS 14735 for waste water or soil waste pipe, with necessary specials,

bends, such as `Y' junction, `T' junction (both single and double), including plugs,

shoes, cowls, flange compression type fittings, wall clips, in proper line and level

with necessary support like brackets/clamps, clips, RCC or brick pedestals or Rupees One Hundred

331 110.00 battens, if necessary, to wall, ceiling and floor, open or concealed complete 149.30 Rmt FourtyNine Paise Thirty

jointing with rubberising and airtight joints, with ‘T’ shaped rubber ring, etc., and Only

lubricant or jointing material, including testing, cutting, making good the wall,

ceiling and floor, etc. Testing & installation of pipe lines as per drawing &

40 mm for waste water for Sink - PVC 10 KG

Providing and fixing Approved SWR Type B quality, heavy duty, UPVC pipes - Ring

Fit & Self Fit, Supreme or equivalent make, Confirming to IS 13592 & Fitting

confirming to IS 14735 for waste water or soil waste pipe, with necessary specials,

bends, such as `Y' junction, `T' junction (both single and double), including plugs,

shoes, cowls, flange compression type fittings, wall clips, in proper line and level

with necessary support like brackets/clamps, clips, RCC or brick pedestals or Rupees One Hundred

332 66.00 battens, if necessary, to wall, ceiling and floor, open or concealed complete 126.47 Rmt TwentySix Paise

jointing with rubberising and airtight joints, with ‘T’ shaped rubber ring, etc., and FourtySeven Only

lubricant or jointing material, including testing, cutting, making good the wall,

ceiling and floor, etc. Testing & installation of pipe lines as per drawing &

32 mm for waste water for Wash basin - PVC 10 KG

Providing, fixing, jointing and testing IS 14735 for Drain PVC SWR 'P' - traps of

self cleansing design with water seal not less than 50 mm., with or without vent,

cutting chases / hole in floors / slabs and bringing the same in proper condition

and shape after placing the trap in right position in case of suspended / open Rupees Six Hundred Six

plumbing or setting the trap in 1:2:4 CC in case of concealed plumbing , etc. Only

complete, as required. The trap shall be 'P' type, of following sizes: 110 x 110 mm

OD inlet / outlet

Providing and fixing Heavy class S.S. grating with Mosquito proof S.S. strainer

of Chilly or equivalent make, as approved, (cockroach trap) including setting in Rupees Four Hundred

floor with cement mortor to match with floor finish as per architect Nineteen Paise Fifteen Only

Providing and fixing, PVC cowl, on C.I / PVC ventilating pipes and verticals for

Rupees Five Hundred Five

335 22.00 soil, waste and rain water Pipes at top level / terrace level, as specified and 505.17 Nos.

Paise Seventeen Only

required, etc. complete. 110 OD PIPE

Providing and fixing, PVC cowl, on C.I / PVC ventilating pipes and verticals for soil, Rupees Three Hundred

336 2.00 waste and rain water Pipes at top level / terrace level, as specified and required, 393.04 Nos. NinetyThree Paise Four

etc. complete. 110 OD PIPE.75 OD Only

Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 100 mm diameter

Rupees Six Hundred

with jali of the following nominal diameter of self cleansing design with C.I scread

337 9.00 614.19 Nos. Fourteen Paise Nineteen

down or hinged grating including the cost of cutting and making good the walls.

NAME OF WORK : CONSTRUCTION OF TALUKA LIBRARY AT SAMI, PATAN, GUJARAT (2ND ATTEMPT)

Qty Item of Work In Rupees Unit Amount In Words

EXTERNAL DRAINAGE

Providing laying (to level or slopes) and jointing reinforced concrete Light duty Rupees Three Hundred

338 11.00 non-pressure pipes I.S., class NP2 of the following internal diameter with collars 359.78 Rmt FiftyNine Paise

and butt ends prepared for collar joints including testing, of joints complete.(B) SeventyEight Only

Providing laying (to level or slopes) and jointing reinforced concrete Light duty

Rupees Two Hundred

non-pressure pipes I.S., class NP2 of the following internal diameter with collars

339 33.00 257.15 Rmt FiftySeven Paise Fifteen

and butt ends prepared for collar joints including testing, of joints complete.(B)

Providing, fixing, jointing and testing salt glazed stoneware Gully trap, class `A',

including excavation in all soil types, bailing or pumping out water from trenches,

shoring whenever necessary testing,refilling, in layers ramming & consolidation,

removing away the surplus earth & spoils, dumping it on site or carting away to

lead of 100 meters as directed, incl. embedding the trap in CC 1:2:4, construction

of brick masonry chamber, internal clear size 300 mm. x 300 mm., in brick work

230 mm. thick, in CM 1:4, plastering inside, outside and all exposed surfaces with Rupees One Thousand Two

340 9.00 CM 1:3, 12 mm. thick, with 300 x 300mm Gully trap chamber & providing, fixing 1,292.19 Each Hundred NinetyTwo Paise

CI frame and cover 300 x 300 mm., weighing together not less than 12.5 Kg., Nineteen Only

painting of all CI items with 3 coats of approved bitumastic paint, etc.

Complete.of the following diameter size:

salt glazed stoneware gully trap, class `A', of 150 mm. dia. inlet and 150 mm.

Providing, fixing, jointing and testing salt glazed stoneware Gully trap, class `A',

including excavation in all soil types, bailing or pumping out water from trenches,

shoring whenever necessary testing,refilling, in layers ramming & consolidation,

removing away the surplus earth & spoils, dumping it on site or carting away to

lead of 100 meters as directed, incl. embedding the trap in CC 1:2:4, construction

of brick masonry chamber, internal clear size 300 mm. x 300 mm., in brick work

Rupees Four Hundred

230 mm. thick, in CM 1:4, plastering inside, outside and all exposed surfaces with

341 9.00 497.14 Each NinetySeven Paise

CM 1:3, 12 mm. thick, with 300 x 300mm Gully trap chamber & providing, fixing

CI frame and cover 300 x 300 mm., weighing together not less than 12.5 Kg.,

painting of all CI items with 3 coats of approved bitumastic paint, etc.

Complete.of the following diameter size:

Cast iron cover 300 x

Providing, fixing, jointing and testing salt glazed stoneware Gully trap, class `A',

including excavation in all soil types, bailing or pumping out water from trenches,

shoring whenever necessary testing,refilling, in layers ramming & consolidation,

removing away the surplus earth & spoils, dumping it on site or carting away to

lead of 100 meters as directed, incl. embedding the trap in CC 1:2:4, construction

of brick masonry chamber, internal clear size 300 mm. x 300 mm., in brick work

Rupees Two Thousand

230 mm. thick, in CM 1:4, plastering inside, outside and all exposed surfaces with

342 9.00 2,017.19 Each Seventeen Paise Nineteen

CM 1:3, 12 mm. thick, with 300 x 300mm Gully trap chamber & providing, fixing

CI frame and cover 300 x 300 mm., weighing together not less than 12.5 Kg.,

painting of all CI items with 3 coats of approved bitumastic paint, etc.

Complete.of the following diameter size:

Gully trap Brick chamber 300 x 300 x

Constructing Inspection chamber 450 x450 x 600 mm clear size in 230 mm thick

brick masonry with cement mortar (1:5) as per ISI with 150 mm thick 1:3:6 P.C.C.

bedding, necessary benching in concrete (M-15) and 20 mm thick smooth cement

plaster (1:4) from inside, C.I. steps as necessary and rough cement plaster 20 mm Rupees Two Thousand Five

343 18.00 thick in c.m. 1:4 outside, with 50 kg. Full size C.I. manhole cover and frame 2,545.86 Nos Hundred FourtyFive Paise

(Approved Make) including all excavation in all soil types, refilling sides in layers EightySix Only

with selected earth ramming and consolidating, removing away surplus soil or

dumping it on site as directed (Depth upto 1500 mm to invert).

Constructing brick masonry chamber for underground C.I. Inspection chamber and

bends with bricks having crushing strength not less than 35Kg/ Cm2 in C.M. 1:5

C.I. cover with frame (Light duty) 455mm x 610mm intenal dimensions total

weight of cover with frame to be not less than 38Kg. (Wt. of cover 23 Kg.) and

Rupees Seven Thousand

frame 15Kg. ) (R.C.C. top slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded

344 18.00 7,180.44 Nos One Hundred Eighty Paise

stone aggregate 20mm size) foundation concrete 1:5:10 inside plaster 15mm

FourtyFour Only

thick with cement mortar 1:3 finished smooth with a floating coat of neat cement