SPL REPAIR TO BLDG NO P72 OR MD ACCN P-26A PROVN OF PARQUET FLOORING IN MT PLATOON BLDG NO P26 02 X CAR PARKING SHED IN FRONT OF OFFICE COMPLEX REQMT OF GENERATOR 15 KVA ANDINSTL OF LIGHTING CONDUCTORS FOR TECH COMPLEX AND AMN STORE AT CHAUBATTIA AND

Amount

B/R Portion Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.complete all as directed.

M & L for screed bed or bedding layer 15mm thick in cement mortar(1:6) for laying floor finishes Complete all as specified and directed.

M & L for non skid ceramic coloured /printed tiles 7 to 8 mm thick (square / Rectangular)area of each tiles exceeding 0.18 sqm but not exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles.

All as per item no 3 for dado /skirting Complete all as specified and directed.

M & L for non skid ceramic coloured /printed tiles 7 to 8 mm thick (square / Rectangular)area of each tiles exceeding 0.11 sqm but not exc 0.18 sqm in floors etc set and jointed in neat cement slurry and pointed in coloured cement to match the tiles.

M&L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4 for backing of Dado/ Skirting & Vertical Tiles.

M & L for glazed ceramic coloured / printed tiles 300mm x 450mmX7mm thick, on vertical surfaces set and jointed in neat cement slurry and pointed in white/coloured cement to match the tiles, complete all as specified and as directed.

M&L for Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified & directed by Engr-in-charge.

Demolition of Reinforced cement concrete of any description and in any position not otherwise specifically provided for. (reinforcement cut as required to facilitate demolition)

M&L RCC Type B1 1:2:4 (20.0mm graded aggregate)for Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like

Formwork to rough finished surface of concrete soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping)

M & L for TMT bars 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exceeding 15 cm thickness.(below or above ground level) Complete all as specified and directed.

M & L for 75 mm thick PCC (1:3:6) type C2 using 40mm graded stone aggregate as in plinth protection finishing the surface even and smooth without using extra cement Complete all as specified and directed.

Surface channel in concrete 1:2:4 (20 mm graded aggregate) for drain complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement complete all as specified and directed.concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc.All as specified and directed.

Taking down cement plaster of any description on brick or stone walls, etc. including racking out joints, hacking for key, scrubbing down with water etc.&removing rubbish to a disance not exc 250m Complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on faces of brick work or concrete surfaces finished even and smooth without using extra cement including mixing of water proofing compound of approved make complete all as specified. Note: WPC shall be measured & paid separately.

Supply only integral water proofing compound complete all as specified & directed.

M&L for rendering 15 mm thick readymade plaster on inner/outer walls with Ultra Tech READIPLAST by adding 17-19% of potable water by weight of material. for thickness above 15mm, it is recommended to be applied in multiple layers. Ready mix plaster shall complies with IS 1661-1972, IS 2250-1965, IS 2402-1963 and confirms the Compressive strength @ 28 days- 10-12 Mpa/Bulk density-1500-1600 kg/cum. Note : The rate quoted by the contractor shall include cleaning of surface, application as per instruction and scaffolding upto 10 mtr height, all as specified and directed. Make - Asian paints/ Fosroc/ Sika/ Ultra tech or equivalent.

M&L for preparation of newly plastered surfaces of wall and applying two coat of oil bound distemper over 1 mm thick (average) wall putty complete all as specified and directed

M&L for preparation of newly plastered surfaces of wall and applying two coats of weather proof exterior emulsion over 1 mm thick (average) wall putty complete all as specified and directed.

M&L for preparation of old decorated surfaces by washing, rubbing down and stopping of painted , plastered or un-plastered surfaces of walls and applying one coat of oil bound distemper white or tinted complete all as specified and directed.

M&L for preparation of old decorated surfaces by washing, rubbing down and stopping of painted , plastered or un-plastered surfaces of walls and applying one coat of weather proof exterior emulsion complete all as specified and directed.

M&L for 3 mm thick applying a layer of JK/ Birla putty on wall surfaces including cornics etc for proper levelling of plaster complete all as specified and directed.

Demolition brick work or stone/ boulder masonery built in cement mortar including all quoins , pillars etc

M&L precast cement concrete 1:3:6 type C1(using 20 mm graded stone agg) as in block masonry with solid blocks exc 10 cm in width and set in cement mortar 1:6 complete all as specified and directed.

M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6m mean radius, built in CM (1:6) complete al as specified

M&L for brick work using sub class ‘B’ old size bricks, straight or curved on plan to any radius in half brick thick walls, built in CM (1:4) complete all as specified and directed.

M & L for 10mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:4, finished even & smooth complete all as specified.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) not exc 1.5 sqm each complete all as specifed & directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5 sqm but not exc 4.0 Sqm each complete all as specifed & directed.

Taking down shutters ( per leaf ) of any description not exc 1 Sqm each complete all as specified and directed.

Taking down shutters ( per leaf ) of any description exc 1 Sqm but not exc 2 Sqm each complete all as specified and directed.

M&L for 2nd class hard wood plain, solid, straight chowkats and frames, wrought, frame rebated on the solid, rounded or chamfered, put together with glue pinned at joints complete all as specified and directed.

S & F in repair MS framed work such as grills, gratings, etc., with end of bars shouldered and / or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders framed balusters; walk ways; railings; frame work of water tanks and similar work conforming to Fe 190-0 or Fe-165-0.

S&F 30 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides complete all as specified & directed.

S & F 35 mm thick 2nd class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats complete all as specified and directed.

S&F 30 mm thick 2nd class hardwood glazed and skeleton window ventilator shutters rebated and prepared to receive glass, gauge etc (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc; sizes of members of shutters as specified in SSR Part I, Section 8, Clause 8.20(b); supplied and fitted in chowkats , but divided into squares, with plain, chamfered or roun ded, mitred and rebated sash bars, any numbers complete complete all as specified and directed.

Factory made single extruded WPC (wood polymer Composite) solid door/ window/ Ceosetory window & other Frames/ Chowkhat of size 45 x 70 mm comprising of PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wwod powder/ rick husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms ) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded stat headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N / mm 2 and resistance to spread of flame of Class A catogory with property of being termite/ borer proof, water / moisture proof and fire retardant and fixed in position with MS hold fast/lugs / SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately).

Factory made single extruded WPC (wood polymer Composite) solid plain flush door shutter of 35 mm thick comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/ cum and screw withdrwal strength of 1800 N (Face) & 900 N (Edge), minimum compressive strength 50 N mm2 modulus of elasticity 850 N / mm2 and resistance to spread of flame of Class A catogary with property of being termite/ borer proof, water/ moisture proof and fire retardanat and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk SS screws, all as per direction of Engineer-In-Charge (Note:- stainless steel butt hinges and necessary SS screws shall be paid separately.

S & F butt hinges, medium weight, Mild steel and fixed, size of hinges 75mm complete all as specified and directed.

S & F butt hinges, medium weight, Mild steel and fixed, size of hinges 100mm complete all as specified and directed.

Supply and fix 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

S & F 100 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F 150 mm long Extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F 100 mm long Aluminium, anodised, barrel tower bolts of extruded section

S & F 150 mm long Aluminium, anodised, barrel tower bolts of extruded section

S & F floor door stopper of chromium plated body with rubber shoe fixed in door, overall length of cover plate 140 mm all as specified and directed.

S&F MS 300mm, ordinary rat tail rod pattern springs including roller and roller plate complete all as specified & directed.

S&F for Block boards , 18/19 mm thick, grade 1 quality, exterior grade, decorative face on both faces Veneering ditto , , fixed with screw to timber frame work in cup board shutters/shelves incl teak wood beading complete all as specified and directed.

M&L for veneered particle board 18/19 mm, solid core, interior grade, with decorative face veneers one face fixed in cup board shutter/shelves complete all as specified & directed.

Supply and fix Continuous (piano) hinges width 30 mm mild steel , bright finish or eletrogalvanised complete all as specified

S & F 3 mm thick Sheet glass, figured , pin headed and glazing with beadings in square not exceeding 0.5 Sqm in each pane complete all as specified and directed.

S & F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with Stainless steel wire staples.

M & L for old painted surface to steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with one coats of synthetic enamel including preparation of surfaces complete all as specified and directed.

M & L for painting to new wood and wood based surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of pink primer including preparation of surfaces.

M&L for preparation of old painted wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying one coat of Synthetic enamel paint (Ordinary tint) complete all as specified and directed.

Taking up or down 15 mm bore steel tubing and connections, including cleaning for refixing or removal to store.

S&F GI water tubing of 15mm dia ,medium grade conforming to IS-1239(Part -1) including all fittings such as bends,tees,short eces,connectors,elbows,reducers,union dockets etc & fixed to walls,ceilings, & laid on floors complete all as specified and directed.

Refixing of old 15 mm bore steel tubing and connections in new or old position (walls, ceiling, floors etc.)

S&F in repair stop valves, cast copper alloy, fancy type chromium plated , screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed for 15mm bore dia of pipe.

S & F in repair vitreous china wash basin, white flat back size 550X400 mm, (flat back or angle back type) including brackets and including cutting for and pinning in ends of brackets or erecting stand, fixed in repairs.

S & F in repair 15 mm bore Fancy type pillar taps, Cast Copper alloy, with capstan heads, chromium plated, screwed down high pressure with or without lettered Hot or Cold with long screwed shanks and fly nuts, screwed for iron pipe and fixed.

S&F 32mm dia waste fittings, brass, chromium plated for glazed ware sinks, basins, etc with long screwed shanks and fly nuts, flange end bedded in red lead cement and other end fixed.

S & F in repair bib taps, cast copper alloy, 15 mm dia, Chromium Plated, fancy type with crutch or butterfly handle, screwed down for iron pipe and fixed etc complete all as specified.

S&F in repair including for S or P trap vitreous china squatting pan, 'Orissa' pattern, size 580mm x 440mm, white, with integral foot rests, including connection to trap, and to flushing pipe, anti-syphonage pipe, etc. in repairs .

S & F in repairs 10 Liters capacity, PVC Valve less, Syphonic action type, low level flushing cistern, white, with inlet ball valve, float, handle, flush pipe of polyethylene of low or high density of PVC, 32mm dia including brackets and connections to pipe complete all as specified and as directed.

S&F in repair 600mmx450mm bevelled edge looking mirror and fixed to wooden plug with CP brass screws and cup washers complete all as apecified & directed

S&F in repair 75mm dia Cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B1 complete all as specified and directed.

S&F in repair brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and directed.

S&F in repair chromium plated Soap dish fixed to plug with chormium plated brass screws all as specified and directed.

S&F in repair sink with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F stainless steel wall mounted plate rack of size 780x760x240mm, made from the stainless steel sheet having thickness 1 mm and weight not less than 7.50 Kg, design & pattern as approved by GE, having sufficient space for placing crockeries, fixed on wall with rawl plug & screws, complete all as specified and directed

S&F in repairs Chromium plated shower rose 125 mm swivel type

S&F in repair 20mm Dia Aluminium alloy anodised curtain rod decorative fancy type with brackets complete all as specified & directed.

S&F in repair PVC connections 15mm dia , 450mm long, , with PTMT nuts & washers at both ends complete all as specified & directed.

Dismatling PVC Water tank Exc 250 & n exc 500 ltr and removing from site as specified and directed

S & F Rotational moulded PVC water storage tanks 500 Ltrs capcity three layer (cylindrical vertical with closed top) hoissted and fixed in position all as specified

S and F Ball brass valve 20 mm dia high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule complete all as specified and directed.

Dismantaling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings complete all as specified and directed.

S&F Pre-painted galvaLume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strenth of 550 Mpa as in roof covering / clading to wall , fixed self tapping screws complete all as specified and directed.

S&F Pre-painted galvatume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of an colour having tensile strenth of 550 Mpa as in roof covering / clading to waall , fixed self tapping screws complete all as specified and directed.

M&L for Dismatling timber scantling 40 sqcm and above in any position ,unframed work complete all as specified and directed

M&L second class hard wood timber in scantling clean sawn any description complete all as specified and directed.

Dismantling of boarding , any description fixed in any position like wall ,wooden flooring and ceiling boards (fiber, pulp, insulation etc,) or insulation boards/slabs/blankets, any thickness including cover fillet complete all as specified and directed.

S & F Second class hardwood 25 mm boarding plain one side with butt joint fixed with nails in any situation. Complete all as specified and directed.

Dismantling of wall and ceiling boards (fiber, pulp, insulation etc,) or insulation boards/slabs/blankets, any thickness including cover fillet complete all as specified and directed.

S & F for Aluminium anodised snap grid frame work for false ceiling comprising of following section for making partitions of 605 X 605 mm size fixed to walls with rawl plugs and screws and hang to roof with s 6 mm dia. G.I. (upto 1200mm length) adjusting levelfixed to roof slabs by means of ceilling cleats made out of G.I.flat 40 x 3 mm size 60mm long and expansion hold fasteners12.5mm dia. 40mm long complete all as specified. size of main tee shall be :- (i)36.5mmx25mmx1.4mm thick, Weighing 0.24Kg/Rm (ii)Cross Tee 23.5mmx36.4mmx1.4mm thick Weighing 0.191 Kg/Rm and (iii)Wall angle 40mmx25mmx2mm thick. Weighing 0.36 Kg/Rm

S & F 4 mm thick non asbestos fiber designer ceiling (E-board classic) board / tiles for insulation and accoustic purpose, 600 X 600 mm size fixed in ceiling with and including dusting of surface complete all as specified and directed

S&F 6mm thick plwood as in ceiling, graded BWR, type BB complete all as specified & directed.

M&L 75 mm thick cement concrete 1:4:8 type D-2 finished fair and even as in sub base Complete all as specified and directed.

M&L for chequred cement concrete tiles of size 300x300x25 mm thick coloured rubber pressed glossy finish, set and jointed in neat cement slurry and pointed in white or colour cement to match the surace of tiles in foor/steps, complete as all specified and directed.

Excavating in post holes (or similar holes) in hard/dense soil each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm complete all as specified & directed.

M&L for plain cement concrete type D-2 1:4:8 (40mm graded aggregate) in foundations, filling and mass concrete complete all as specified & directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section embedded in PCC, including taking out embedded portion and making good disturbed ground complete all as specified & directed.

M&L for MS work in hand rails, half round or other steel section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts;posts and struts in fencing including cutting tops to shape as directed, drilling holes,notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 complete all as specified & directed.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards, rails, straining bolts, etc. including provission of binding wire complete all as specified & directed.

Supply only chain link MS galvanisd fencing, any size or type complete all as specified & directed.

S&F in repair Galvanised. 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails strain- ing bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified & directed.

M & L for painting to new steel and iron surfaces of any description, over 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified and directed.

M & L for painting to new steel and iron surfaces of any description, not exc 10 cm in width or girth, not otherwise described with two coats of synthetic enamel paint over a coat of red oxide primer including preparation of surfaces complete all as specified and directed.

M&L Mild steel screw bolts (machine made) 11 to 15mm dia with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but not exc 10cm long complete all as specified & directed.

Dismantling wrought iron or mild steel work of any description specifically provided for gates, staircase railings, framed truss etc complete all as spd and directed.

M&L Joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) Fe 410 -W (Gde- E- 250) quality- A

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.

M&L for preparing newly plastered wall surfaces and applying two coat of distemper oil emulsion over 1mm thick wall care putty, complete all as specified and directed.

S & F Factory made 35 mm thick Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated

S & F 3.00mm thick Sheet glass, ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in each pane with hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beadsall as specified and as directed.

M &L Squared rubble walling Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in CM 1:6, complete all as specified and directed

ditto- as per item no 110 above, but except stone

Extra over to stone walling for hammer dressing to face stones and dressing of the face beds & joints as specified of squared rubble walling regular coursed, Jodhpur type, with maximum depression of face from straight edge held against the dressed surface n.exc. 20mm.

M & L Providing PCC type B1 (1:2:4) using 20mm graded aggregate in win- dow or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone walling), corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throat- ing etc. and setting in mortar complete with joints to match in CM 1:4

M&L for rendering 15 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished fair and even without using extra cement complete all as specified and directed

Demolition of cement concrete (reinforced) in roof,roof projection,chajja and similar works in any position.

M&L for Reinforcement cement concrete nominal mix 1:2:4 type B1 using 20mm graded stone aggregate for chajja, roof projection, facia and similar works all as specified & directed by Engr-in-charge.

Formwork to chajjas ,roof projection and similar work including edges with rough finished surfaces of concrete including height upto 6 mtr.

S & F MS steel TMT bars 10mm dia and over cut to length bent to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips, quality conforming to IS 1786-1985 complete all as specified and directed

M&L Precast concrete interlocking paver block rubber moulded any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment laid over with 25mm thick sand cushioning over 75mm thick PCC type D2 (1:4:8) using 40mm graded aggregate as in subbase of flooring/hardstanding including demolition of concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) , complete all as specified & directed by Engineer-in-charge. Note :- (i) Rate quoted by the contractor shall deemed inclusive of PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) packing and finished even and fair to the sides of pavement.

M&L for 9mm thick plywood, graded BWR, type BB fixed with rawl plug and screws to timber framework complete all as specified and directed.

S&F for 8mm thick, wooden pieces, machine presured one side laminated and other side balancing green, as in parquet flooring with and including necessary padding as soft wool graded type as required at site, fixed with adhesive as per manufacturer's instructions including taking down old wooden flooring with or without plywood complete all as specified and directed.

S&F steel work in tubular trusses including special shaped washer etc complete using ERW or induction butt welded tubes for vertical post, purlins and rafter complete all as specified and as directed by Engineer-In-charge.

S&F MS plates (plain or chequered), channels, square cut or notched (ordinary and counter sunk) forming holes, with fixing attachment,Fe-290(Gde E-165) complete all as specified & directed by Engr-in-charge

Surface excavation not exceeding 0.30m deep and averaging 15 cm deep and getting out in hard/dense soil complete all as specified and directed by Engr-in charge .

Excavating in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or n. exc.10 Sqm on plan and n. exc. 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in hard/dense soil complete all as specified and directed.

M&L for Reinforced Cement Concrete (nominal mix) type B-1 1:2:4 (using 20mm graded aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles complete all as specified and directed.

M & L for 40mm thick damp proof course to horizontal or vertical surfaces including necessary formwork in cement concrete (1:2:4) type B-0 (using 12.5mm graded stone aggregate) complete all as specified and directed.

M & L for applying evenly a coat of blown type bitumen @1.50 kg / Sqm and blinding with clean dry sand @ 0.05 Cum/ Sqm complete all as specified and directed.

M & L for polythene film, 50 micron thick, laid over with and including on a coat of bitumen primer, @ 0.30 to 0.50 kg /Sqm complete all as specified and directed.

Formwork to rough finished surface to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundations and plinth beams and similar work vertical or to batter complete all as specified and as directed.

M & L for 100mm thick PCC (1:3:6) type C2 as in sub floors, sub-bases, floors and pavings, under tiles etc complete all as specified and directed.

M&L hardcore for broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface Complete all as specified and directed.

S & F Galvanised, corrugated mild steel sheeting 0.63mm with two corrugations side lap, fixed with coach screws and washers, in roofs , walls etc. with gradeof zinc coatiing 275 complete all as specified and directed.

M & L for rolled mild steel work as in rafters, purlins etc where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates confirming to Fe-410-W-(Gde-E-250) quality-A complete all as specified and directed.

Supply & Fixing powder coating (minimum thickness of powder coating 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

Supply and fixing powder coating (minimum thickness of powder coating 50 micron) anodised aluminium door shutters, aluminium section weighing 0.55kg/m incl necessary joining cleats, glazing clips, rubber neoprene packing, handles 02 Nos in each door, hinges, anodised aluminium snap beading screws etc. complete all as specified and as directed.

Supply & Fixing three track aluminium powder coated sliding window with three sliding shutter, the size of outer frame three track 100x37x1.5mm (using two track for glazed window shutter and one track for wire gauged), the section shutter size 37x18x1.2mm and glazing with 5mm thick transparency glass of poly carbone including all around suitable rubber gasket and stainless steel wirecloth 0.36 mm nominal dia of wire and average width of aperature 1.4mm and fixed on aluminium flat and inserted in the frame of shutter with tracking arrangement each sliding window shall be provided with one number handle including locking arrangement & 2 numbers sliding rollers of nylon with including all necessary fittings complete all as specified and directed.

S&F Mortice lock, brass, vertical type, size 100 mm 4 levers complete all as specified and directed.

M&L for 18/19 mm thick Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work as in cupboards/kitchen cupboard with teak wood beading on all side fixed complete all as specified and directed.

S&F steel door including projecting type hinges, steel handle, complete, with glazing bars, dovetailed or welded complete all as specified and directed.

S&F pressed steel frames for doors of size 105 x 60 mm with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete, as specified, supplied and fixed.

S & F 20mm Dia Aluminium alloy anodised curtain rod decorative fency type with brackets complete all as specified.

M& L for forming embankments including raising (or lowering) earth, spreading in layers n exc. 30 cm thick; watering, ramming/rolling and finishing to required size, shape, etc., n exc. 1.5m high from base complete all as specified and as directed.

E/M PortionTaking down carefully Aluminium/copper wiring of any size (for light, fan, socket or power etc complete) ( fittings such as switches, sockets, ceiling roses, pendent holders regulators, tube lights etc to be measured and paid separately) and making good disturbed surfaces of wall, roof etc to match with existing surface complete all as specified and directed.

M & L point wiring for Modular fittings for one light point/ fan/ bell/ 5Amps socket out let (independent)point controlled by one, one way switch with 1.5 sqmm size, PVC insulated and unsheathed 1100volts grade, single core stranded (multistrand) copper conductor (FR-LSH) PVC cable drawn into & including medium grade PVC conduit (not less than 20mm outer dia )with all fittings and accessories fixed concealed (including chase cutting in brick/ stone masonry walls for fixing conduit and plastering and whitewash/colouring the external surface and matching the same with existing surface) incl modular metal flush box for mounting modular fittings and covered with modular cover plate with frame and cup washers including one continuous run of PVC insulated (green colour) 1.5 Sqmm multistranded copper conductor cable earth wire and connected to earth dolly complete all as specified and directed ,are as follows :- (a) One light/One fan/one bell point controlled by one modular switch

(b) One modular socket outlet 3 pin 6 amps controlled by one switch on same board.

(c) One modular socket outlet 3 pin 6 amps controlled by one switch on independent board.

All as per item No 145 herein before but wiring with 2.5 sqmm copper wire (FR-LSH) PVC and 2.5 sqmm earth wire for modular socket outlet 5 pin 16 amps on independent board.

Supply and fix modular type switch single pole, one way 6 Amp complete all as specified and directed.

Supply and fix socket out let multi 5 pin, 6 Amps, modular type complete all as specified and directed.

Supply and fix switch modular type single pole, one way 16 Amp complete all as specified and directed.

Supply and fix socket out let 2 in1,3 pin, 6 and 16 Amp, modular type complete all as specified and directed.

S&F ceiling rose, PVC/ Poly carbonate,isolated body three terminal complete all as specified and directed.

S & F lamp holder angle type PVC/Poly carbonate type insulated body with back plate suitable for batten/wall fitting complete all as specified and directed.

Supply and fix High quality LED T8 indoor batten tube light 20 Watt with aluminium extrusion in D shaped have large diameter for increased convection heat transfer incl one LED PC tube rod and driver, internaly pre wired of 1.5 sqmm twin twisted flexible cable all as specified & directed. NOTE: The contractor must submit 5 years warranty for LED fitiings.

Taking down unservicable MCB and S&F MCB SP, 240 volts,AC C curve, 10 KA 6 to 32 Amps .

Taking down unservicable MCB and S&F MCB SPN , 240 volts,AC B curve, 10 KA 40 Amps.

S&F sheet metal enclosure single pole and neutral with a two pin and earth plug and socket complete with one single pole MCB 240 Volts 20 Amps including one 15 Amp switch on existing board with wiring for switching geyser on/off complete all as specified and directed.

Supply & Fixing of non metallic PVC conduit 25 mm exclusive of boxes but includinf of all tees,bends,elbows, reducers,bell mouth tube ends and fixing accessories such as couplers,lock nuts,saddles, pipe hooks etc. concealed in wall ceiling floor etc for television/DTH/telephone/Data cable complete all as specified and directed.

S& F socket outlet for TV/Video/audio device modular type with inner and outer modular plate type, specially built for wall/high mounted TV and inc pressed steel/metal flush box concealed complete all as specified and directed.

Supply and fixing LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 66 protection complete. all as specified and directed .NOTE : The contractor must submit 5 years warranty for LED fittings

Taking down unservicable DB and S&F sheet metal enclusure for DBs(double door type) single pole and neutral 12 way including blanking platge as required with 200 Amps rated bus bar, 240 volts fixed complete all as specified and directed .

S & F LED bulk head fitting, 1 x 10 watt with PDC aluminium housing and milky diffuser including LED light driver holder, complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230 Volts, 50 Hz complete all as specified and directed. NOTE: The contractor must submit 5 years warranty for LED fittings

M&L for earthing complete with galvanised steel, earth plate electrode 600x600mm x 6mm thick burried directly in ground verticaly (earth pit not less than 2.25 mtrs below ground level ) with top edge of the plate not less than 1.5 mtrs below normal ground level connected to galvanised earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanised iron/steel all as shown in electrical plate No 3 on page 497 of MES schedule 2009 part - I connected to main switch board/main DBs/earthing test point including all necessary excavation and earth work in hard/dense soil common salt and charcoal dust mixed and packed 150mm thick all round the GI earth plate, watering pipe 20mm dia GI medium grade. GI sheet 0.63 mm thick funnel, wire gauge, 50mm thick RCC cover in PCC 1:2:4 type B1 duly reinforced with MS round bars 6mm dia @ 150c/c both ways and pit/chamber in PCC 1:3:6 type C1 with suitable lifting handle to cover, GI protection pipe 15mm dia light grade up to 7.5mtr from electrode GI pipe to be fixed with complete all as specified and directed. Note :- (i) Earth lead beyond 7.5 mtr from electrode to earth terminal point/main switch & GI pipe light grade 15mm dia for protection against mechanical damage to lead shall be measured separately. (ii) On testing after completion if desired earth resistance is not obtained, the earthing will be redone at no extra cost.

S & F call bell ding dong AC, 230V single pole fixed over with and including sunk spressed steel box of size 175mmx100mm with 3mm thick plastic laminated backalite shut cover fixed with brass screw complete all as specified and directed,

S&F modular bell push, 6 Amp 1 module complete all as specified and directed.

S& F LED Bulb of 9 watt as specified .NOTE: The contractor must submit 5 years warranty for LED fittings

Supply and fixing LED light fitting Mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with two core flexible copper conductor cable of suitable size complete all as specified and directed. NOTE: The contractor must submit 5 years warranty for LED fittings

Supply and fixing Geyser 25 Ltr Capacity ,CRCA Metallic body,Stainless Steel (SS) Inner tank, BEE five star rating, heating element upto 2 KW, ISI mark, with all accessories such as safety valve, thermostate, NRV, connection piece etc & making 04 Nos hole and grouting of suitable size of nuts and bolts and making good as per existing surface all as specified and directed

S & F Exhaust fan plastic body heavy duty ISI mark, 250 mm size with louvers including all connecting accessories and cutting opening on wall and making good as per existing surface complete all as specified and directed

Supply, laying and testing cable XLPE Insulated screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 16 Sqmm 2 core.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m deep for laying of underground cable and getting out in any type of soil complete all as directed by the Engineer-in-Charge

Returning, filling in, including spreading, leveling watering and well ramming in layers n.exc 25 cms. thick in soft / loose soil complete all as specified and directed by Engr -in -charge .

Removal of surplus soil not exceeding 50 Mtr and depositing where directs at a level not exceeding 1.5 Mtr above the starting point complete all as specified and directed by Engr-in-Charge.

M&L for sand cushioning in trenches spreading and consolidation 8cm thick before laying the cable & 15 cm of sand after laying the cable complete all as specified

M&L for laying of bricks well burnt sub class ‘B’ (old pattern) laid flat for cable protection width equal to the lengrth of brick complete all as specified .

M & L galvanised steel water tubing 'light grade' 25 mm bore with all fittings laid under the roads, drains, culverts and fixed on poles etc complete all as specified and directed .

Taking down unservicable DB and S&F sheet metal enclusure for DBs(double door type) single pole and neutral 4 way including blanking platge as required with 200 Amps rated bus bar, 240 volts fixed complete all as specified and directed .

S&F Exhaust fan metallic bady ISI mark, 300 mm size with louvers including cutting openings, through brick/ stone wall , making of holes and grouting of suitable size of nuts and bolts for 300 mm exhaust fan and making good dismantled portion and making connection with wire of suitable size and connecting accesssories complete all as specified and directed.

Taking out old U/S service connection cable for replacement including S&F service connection cable, 1100 volts grade heavy duty PVC insulated aluminium conductor, 16 Sqmm 2 core size, served with inner sheathing of PVC tape and overall PVC sheathed in service connections suspended by insulating hangers not more than 1 metre apart including 4mm suspension wire, one twin core cable flat or circular, complete all as specified and directed.

Supply, installation, testing & commissioning of diesel engine silent generator set with acoustic enclosure confirming to latest CPCB norms, water cooled capacity 15 KVA ( generator out put should be 15 KVA/12 KW) 50 Hz AC supply, engine as per IS : 10001/ 10002 and alternator as IS : 13364 complete including engine alternator mounted on common base frame and canopy fabricated from steel channel of suitable size, engine and alternator shall be anti vibration mounting pads,sound proof canopy as per latest CPCB norms and foundation as per manufactures instruction / design complete all as specified directed with and including the following provision :- (a) ALTERNATOR :- Alternator of capacity 15 KVA/ 12 KW at 0.80 power factor after considering derating factor AC 3 phase , 415 volts, 50 Hz, 1500 RPM brushless type self excited, self regulated screen protected type and AVR system. (b) DIESEL ENGINE:- Diesel engine air cooled suitable for alternator of 15 KVA capacity considering all points for derating factor taking into account the altitude, humidity of maximum temperature of Ranikhet with the following provision :- (i) Radiator and sound proof canopy as per latest CPCB norms and foundation etc. of capacity 15 KVA (ii) Fly wheel (iii) Air cleaner (iv) water pump with thermostat (v) Electric starting system with the help of batteries as per manufacture's specification with key ignition and push button (vi) Temperature meter and oil pressure gauge (vii) Fuel tank of made of mild steel sheet of required capacity as per standard with inlet and out let connection, filling cap, drain valve air vent with calibrated scale on outdoor surface floor mounted with suitable angle iron support (viii) Fuel/ oil filter (ix) Battery charger as per manufacturer's recommendation (x) Battery maintenance free with connecting lead. Make Exide / Amaron/Luminous (xi) Foundation as per manufacturer's instruction/ drawing (xii) Heating system to start engine during winter season (xiii) Engine protection device against short circuit overload low lubricanting oil high pressure water temperature and over speeding of engine (xiv) Anti vibration mounting pad - set of 6 Nos (xiv) Exhaust system up to required height and length (xv) Engine warranty and test certificate (xvi) RPM meter and hour meter (xvii) Including Gen set control unit complete The DG Set must include the following features • Compact size with Manual/ Automatic starting system. feature. • Sound Proof, Weather Proof enclosure. • Low vibration,with electronic fuel injection system • Class G3 Governing in its range, which gives better accuracy in decreasing the speed drop in transient and lowering th recovery time of the speed. • Confirms to latest Govt. CPCBIV+ emission & • The Enclosure should be of modular construction with the provision to assemble and dismantle easily. • The sheet metal components should be 9 tanks pre treated and should be polyester based powder coated (inside as well as outside) for long life. • All Nuts-bolts, hardware should be of Stainless Steel for longer life. • Battery must be provided in a tray inside the enclosure. • Doors must be gasketed with high quality EPDN gaskets to avoid leakage of sound • Optimised EATS (Exhaust After Treatment System) should be provided to control emission & exhaust noise.with sound attenuators to control sound at air entry & exit points inside the enclosure• Adequate ventilation should be provided to meet air requirement for combustion & heat removal

M&L for earthing complete with galvanised steel, earth plate electrode 600x600mm x 6mm thick burried directly in ground verticaly (earth pit not less than 2.25 mtrs below ground level ) with top edge of the plate not less than 1.5 mtrs below normal ground level connected to galvanised strip 32x6mm as earth lead by means of bolts, nuts, check nuts and washers of galvanised iron/steel all as shown in electrical plate No 3 on page 497 of MES schedule 2009 part - I connected to main switch board/main DBs/earthing test point including all necessary excavation and earth work in hard/dense soil common salt and charcoal dust mixed and packed 150mm thick all round the GI earth plate, watering pipe 20mm dia GI medium grade. GI sheet 0.63 mm thick funnel, wire gauge, 50mm thick RCC cover in PCC 1:2:4 type B1 duly reinforced with MS round bars 6mm dia @ 150c/c both ways and pit/chamber in PCC 1:3:6 type C1 with suitable lifting handle to cover, GI protection pipe 40mm dia light grade up to 7.5mtr from electrode GI pipe to be fixed with complete all as specified and directed. Note :- (i) Earth lead beyond 7.5 mtr from electrode to earth terminal point/main switch & GI pipe light grade 40mm dia for protection against mechanical damage to lead shall be measured separately. (ii) On testing after completion if desired earth resistance is not obtained, the earthing will be redone at no extra cost.

Supply, laying and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of of size 35 sq mm 3½ core

Excavation in trenches in hard/dense soil not exc 1.5 mtrs wide and not exc 1.5 m in depth for laying cables and getting out incl jointing bottom surface to the reqd level/slope etc complete all as specified and directed.

Returning filling in incl spreading, leveling, watering and well ramming in layers not exc 25 cm in hard/dense soil all as specified and directed.

M & L galvanised steel water tubing 'light grade' 50 mm bore with all fittings laid under the roads, drains, culverts and fixed on poles etc complete all as specified and directed .

Supply and fix ON LOAD change over switch 415V in sheet metal enclosures 4 pole of capacity 63 Amps.

Supplying and laying synthetic Rubber insulated mats 2 mm thick for voltage upto 3.3 kv for electrical purpose as per IS 15652-2006, (superseding IS 5424) suitable for electrical shock safety of sizes 2m x 1m.

Supply and fix High quility LED T5 integrated batten tube light 20 Watt with aluminium extrusion with frosted PMMA/PC diffuser, internaly pre wired of 1.5 sqmm twin twisted flexible cable all as specified & directed.

Supply and fixing LED luminaire 600mmx600mm, 35/36 watt, 220 volt, AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including necessary cutting as required in panel and connecting up with driver three core flexible copper conductor cable of suitable size complete all as specified & directed.

S & F MCB single pole, 240 volts, 5 to 32 Ampere, rupturing capacity 10 KA, ‘B’ curve type in the MCB DB including taking down complete all as specified and directed.

S & F in MCB SPN, 240 volts, 32 Amps, rupturing capacity 10 KA, ‘C’ curve type complete all as specified and directed.

S & F in MCB SPN, 240 volts, 40 to 63 Amps, rupturing capacity 10 KA, ‘C’ curve type complete all as specified and directed.

Supply and fixing sheet metal enclosure for DBs(double door type) single pole and neutral 8 way including blacking platge as required with 200 Amps rated bus bar, 240 volts fixed complete all as specified and directed .

S&F sub main wiring with two single core FR-LSH PVC insulated and sheeted i 100 Volts grade 2.5 sqmm size cables PVC insulated stranded copper condutor fixed in PVC condunt pipe 25mm dia with all accessories and one continuous run of 25 Sqmm copper conductor pvc (including chase cutting in brick/stone masonery wall for fixing conduit and plastering the external surfaces and matching the same with existing surface) (Note- Two single core cables along with earth wire and condunt shall be measured as one unit length)

Material and Labour for replacing insulation deteriorated PVC insulated twin core flat 10 Sqmm, 1100 Volts grade heavy duty multistranded aluminium, conductor cable in service connection suspended by insulating hangers not more than 1 mtr apart including 4mm dia GI wire including taking down complete all as specified and as directed. Make : Finolex/Paragon/Plaza

Supply and Installation of fully autonomous,CPRI tested Early Streamer Emission Lightning Conductor (ESELC)with (gain in triggering time)of minimum of 20 us,radius of protection 37 meters in level 1 protection zone when installed on 5 meter mast along with other accessories for installing ESELC on the roof top of the Building/tower for the protection of the building/structure from direct lightning strikes. Make :-Tercel, Model Tz20 or equivalent make.

Supply and laying of 70 Sqmm copper flexible wires as down conductor from air terminal to the earth test link installed on the wall of the building 2 mtrs above the ground.

Supply and installation of lightning transient event counter resettable 6 digit LCD display with in built lithium battery in IP67vrating enclosure with transparent lid, mounting arrangements etc,as required.

Supply and laying of 25x3 mm Copper strip from Earth Test link to the Earth pit through 40mm B class GI pipe

Providing & creating of CPRI Tested earth pits material using ISOGEL earth enhanced compound of 20 kgs, ISOROD advanced chemical earth rod made with copper tube of 2.5" dia, 8 fit long,1.6 mm thick installed vertically or horizontally as per the side condition complete with glanges bends top cover heavy duty plastic inspection chamber including excavation and refilling etc as required. Make:-Tercel, Australia or equivalent make.

KUMAON VALLEY CONSTRUCTION (BID ID -3463854)

M/S NAYAL ELECTRICALS (BID ID -3470544)