REPAIR TO ROOF, FLOOR, JOINERY ETC INCLUDING CONNECTED APPROACH PATH IN CERTAIN SEWAGE SUMP/PUMP HOUSE AT MIL STN JAMNAGAR

Amount

Taking down all existing roof treatment incl wire brushing and cleaning loose dust etc from surfaces of RCC roof incl flashing and juntion of parapet complete all as specified.

Demolition of cement (un-reinforced) in any position not otherwise specifically provided and removal of debris out side of MD land complete all as specified and as directed.

M&L 25mm thick (Avg) PCC 1:2:4, type B0 (using 12.5mm size stone aggregate) as levelling course/padding with slope complete all as specified

M&L 10 mm thick cement plaster in CM 1:3 mixed on padding layer surface finished even and smooth without using extra cement for roof treatment with WPC (liquid water proofing compound) complete all as specified

Supply only Integral waterproofing compound

M&L for Water proofing treatment to RCC roof slab including parapet comprising with the following course of treatment / specification from bottom to top:- (a) Applying bituminous primer @ 0.40 litre per Sqm over plastered surfaces of roof including parapet surfaces. (b) one layer of APP based polymeric membrane of approved manufacturer, 3 mm thick, weight not less than 3.6 Kgs per Sqm, reinforced with non woven polyester fabric or weight not less 150 gms per sqm. Polymeric membrane shall be taken to a height of 60 cm 9 minimum) and then inserted inside the groove of parapet wall and shall be finished by a membrane flashing. Note:- (i) Laying of APP based membrane shall be done by torching method and as per manufacturer's instructions. (ii) A minimum overlap of 150 mm and 100 mm should be made in the end and sides of the polymeric membrane respectively and all overlaps and joints are properly sealed as per manufacturer's instructions. (iii) Applying two coats of Bituminous aluminium paint on top of APP membrane cover including testing on completion complete all as specified and directed.

Taking down cement plaster of any description on brick or stone walls or concrete surface incl raking out joints hacking for key, scrubing down with water etc. all as specified and as directed by Engr-in-charge.

M&L for rendering 5mm thick in CM 1:3 on concrete surfaces in ceiling including finishing even and smooth without using extra cement

M&L 10 mm thick rendering on fair faces of brick work or concrete surfaces in cement plaster 1:6, finished even and smooth w/o using extra cement all as specified.

M&L 15mm thick rendering in two layers of 10mm in CM 1:6 and top layer of 5mm thick in CM 1:4 on external stone/concrete wall surfaces with WPC including finished even and smooth w/o using extra cement all as specified and directed. (Note (a) WPC coumpound shall be used in second layer (b) intergial WPC shall be paid seperately on supply only )

M&L Preparation of newly plastered surfaces of ceiling and applying three coats of white wash on ceiling all as specified and as directed by Engr-in-charge.

Preparation of newly plastered surfaces of wall incl sweeping clean with brush to remove loose dust, sand, etc and applying two coats of heavy duty waterproofing coat (Dr Fixit Wounderproof-1 or techo commercial equivalent product of specified make) by mixing water @ 25-30% to make slurry coating and allow 4 to 6 hrs time for drying up of first coat before application of second coat in perpendicular direction of first coat and further left to dry for 4 hrs (APP Membrane :- STP Ltd/ Texsa India Ltd/ IWL Ltd/ Tiki Tech/ Asian & Waterproofing Chemicals:- M/S ChokseyChemicals,M/S AppurvaIndia Ltd,Bostick India Ltd,Stp Ltd, M/s Maruti) complete all as per manufacturer instructions as directed by Engr-in-charge.

Material & labour for preparation of new surfaces of walls and applying two coats of distemper oil emulsion over a coat of primer over and including 3mm thick wall care putty complete all as specified and as directed by the Engr-in-Charge.

M&L Preparation of newly plastered surface and applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces.

M & L for preparation of old distempered surfaces of walls including washing, rubbing down and stopping nail holes etc and applying one coat of oil bound distemper (oil emulsion), white or tinted on walls complete all as specified.

M&L Preparation of old painted wooden surfaces of any description over 10 cm in width/girth and applying one coat of synthetic enamel paint with smart painting too complete all as specifed and directed.

M&L for preparation of old painted steel surfaces of any description, not otherwise described, over 10cm in width or girth and applying one coat of synthetic enamel paint on steel surfaces all as specified.

Material and labour for complete removal of existing treatment from plastered or unplastered surfaces of walls including cleaning with scrapers, any number of coats and any width or girth etc, the area of application should be cleaned thoroughly, remove all dirt, dust and uneven elements from the surface by washing and scraping and all the unevenness in the surface should be corrected by filling the exterior wallcare putty, surface should be sanded down with fine grade sand paper for smoothness applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over old surfaces,all as per manfecturars instructions as directed by Engr-in-charge.

Removal of all loose/unsound/bad/damaged concrete or plaster existing RCC structure of slab/beams/walls by using chesel/hammar .Cut and remove unsound reinforcement bars, wires etc without damaging the sound reinforcement but , clean loose rust from bars manually with brush . fixing mild steel welded fabric of weight exceeding 3.5 kg but n Exc 4kg /Sqm with existing bars or by welding on it after cutting the RCC to the sound bar if the existing bar is damaged (Incld provn S&F new TMT bar whereever required ). Applying eppoxy bonding agent and making good with polymer modified plaster and micro concrete as required thickness over a coat of rust removing alkaline primer and match the finishing to the existing surface in ground floor including form work complete all as specified and directed by Engr-in-charge.

Demolition of stone slab and tiles of any description or thickness in floors, apron etc laid, bedded and pointed in any mortar.

M&L Non skid Ceramic coloured Joint free tiles of 7-8mm thick (area of each tile exceeding 0..06 Sqm but n.exc. 0.11 Sqm) as in floor set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles over and including 15mm thick bedding layering cement mortar (1:6) complete all as specified and directed by Engr-in-charge.

M & L for Glazed ceramic tiles, coloured (light colour as approved), of size 450X 350X 7mm / 450 x300x7mm thick on vertical surfaces such as in skirting/dado etc set and jointed in cement slurry over and including 10mm thick rendering in cement mortar (1:3) and pointed in white cement with pigment to match the colour of tiles complete all as specified and directed by Engr-in-charge.

S&F Powder coated aluminium anodised sliding window of 3 track, frame and shutters of section (a) Three Track Frame:- (i)Bottom - 20832 (ii)Top/side – 20831 (b) Shutter:- (i)Bottom – 20736 (ii)Top/Side – 20738 (iii) interlocke - 20737 (c) DECO GRill - amluminium anodised grill (girll No. 20) or appropriate equivalent section, shutter fixed with 4 mm thick tinted sheet glass and rubber gasket, handles, locking arrangement and SS wire mesh SS wire cloth 0.36mm dia of wire and average width of aperture 1.40mm, including making opening for handle & fittings, fixed with complete all as specified and as directed by Engineer-in-Charge. Itam rate includs for making good jambs, cills etc and including taking down old window complete all as specified and directed by the Engr-in-Charge. NOTE : (ii) Rates include all glazing/aluminium wire cloth, rubber packing, joining, cleats, glazing clips, aluminium snap beading, locking arrangements, etc (iii).comprising frames of (Jindal aluminium section or equivalent as specified) No:20831 three track top & sides, 20832 three track bottom, 20738 top and side shutter,20736 bottom of shutter 20737 inter lock (both sides of wire mesh shutter and one sides of glazed shutter), incl "C" channel and "L" angle, roller bearing, rubber beading, consealed lock.

S&F in coloured aluminium anodised adjustable louvered ventilator, frame of section 63.5mm X 38.1mm X 1.47 mm or higher appropriate equivalent section with aluminium adjustable lovers with 4 mm thick figured/frosted sheet glass with rubber gasket, SS wire cloth 0.36mm dia of wire and average width of aperture 1.40mm incl necessary channel frame work, handles, locking arrangement etc incl making good jambs, cills etc and including taking down old iron ventilator complete all as specified and directed by the Engr-in-Charge. Note Quoted rates shall include all glazing / SS wire cloth, rubber packing,jointing,cleat, glazing , snap beading etc.

Taking down Chowkats or Frames,not exc. 1.50 Sqm Each with Shutters (without Taking Off Shutters from the Frames), complete all as specified and as directed.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, supplying & fixing in opening as per specification & drawing, complete all as specified and as directed.)

M&L Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, supplying & fixing in the frame at site as per specification & drawing complete all as specified and as directed.

S & F 100mm Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B1

S&F Extruded aluminium alloy handles 150mm long, fabricated type, anodised.

S&F Aluminium anodised barrel tower bolts, 150 mm long, of extruded section.

Demolition of cement concrete (un-reinforced) in ground floors and paving n exc. 15cm thickness (below or above ground level) including surface excavation and removing bedris out side MD land all as specified and as directed by Engr-in-charge.

M&L for providing 75mm thick plain cement concrete( 1:3:6) type C-2 using 40mm graded aggregate as in sub based. Complete all as specified and as directed by Engr-in-charge.

M & L for 40mm thick, cement concrete 1:2:4,type B-1,using (20mm graded stone aggregate) as in floors etc.and finished finished even and fair with out using extra cement Complete all as specified and as directed by Engr-in-charge.

Forming construction joint 30mm deep x 10mm wide filled with sealing compound, Grade ‘A’

M&L hard core broken stone or boulders of 63mm gauge, deposited spread and leveled in layers not exceeding 15cm thick watered and well rammed to a true surfaces all as specified and as directed.

M & L for 100 mm thick plain cement concrete type C2 (1:3:6) using 40 mm graded aggregate as in path, hard standing, parking floors and paving etc.

Demolition of stone slab and tiles of any description or thickness in floors, apron etc laid, bedded and pointed in any mortar.

S&FMachine pressed precast concrete interlocking paver block (coloured) any shape and size conforming to IS 15658-2006 of 60mm thick M-35 grade (with grey cement and pigment) over and including 50 mm thick sand coushioning complete all as specified and directed.

Providing and laying / fixing at or near ground level factory made kerb stone of M-25 grade cemenet concrete in position to the requierd line, level and curvature, jointed with cement mortar 1 :3 (1 cement : 3 coarrse sand), including making joints with or withourt grooves (thickness of joints except at sharp curve shall not to more than 5mm) including making drainage opening wherever required complete all as specified and directed

S & Fixed Vitreous China Squatting Pan ‘ORISSA’ Pattern, size 580X440 mm White, with , Integral Foot Rest, providing Joints between Flush Pipe and Socket of WC Pan (excluding Flushing Cistern and Flush Pipe), and connected Items, complete all as specified and as directed.

S&F in repairs Vitreous China wash hand basin white flat back, size 550mm x 400mm, cutting for and pinning in ends of brackets including waste pipe, CP waste coupling, brackets but Excluding Tap ,complete all as specified.and directed.

S&F 10 Ltr capacity PVC valveless symphonic action type flushing cistern, low level with inlet , ball valve, float all as specified including necessary 32 mm dia flush pipe and making all necessary connection as directed.

S & F in repair 15mm Bib taps, cast chromium plated with crutch or butterfly handle, long body screwed down joint with adhesive taflon type screwed for iron pipe or for brass ferrule and fixed

S&F in repairs angle cock 15 mm bore cast copper fancy type chromium plated alloy screwed down high pressure with crutch or butter fly handle serwed both ends for iron pipe or for unions

S & F in repair 15mm Pillar taps fancy type, cast copper alloy, with capstan heads, chromium plated,screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nuts, joint with adhesive taflon type screwed for iron pipe or for brass ferrule and fixed

S&F 450 mm long PVC connection suitable of 15 mm nominal bore GI pipe complete with PTMT nuts complete all as specified and as directed.

Supply, lay, connect and test 15mm bore GI tubing ,medium grade with all fitting, laid in trenches, or fixed to walls, floors, ceiling or laid in trenches etc. fixed in repair complete

Supply, lay, connect and test of 20mm bore GI tubing ,medium grade with all fitting, laid in trenches, or fixed to walls, floors, ceiling or laid in trenches etc fixed in repair complete

S&F in repair 500ltr capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position with 20mm PTMT ball/float valve etc complete all as specified and as directed by Engr-in-charge.

Ravi enterprise

jitendra c joisar