SPL REP TO BLDG NO P-158 (ANCY,INST,ARMOR SHOP AND MOTIVATION HALL) AT MIL STN JAMNAGAR

Amount

Dismantling of Asbestos cement (Plain,corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and as directed by Engr-in-Charge.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engr-in-Charge.

S&F Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and as directed by Engr-in-Charge.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) any thickness, incluing cover fillets, complete all as specified and as directed by Engr-in-Charge.

S&F Anodised aluminium snap grid frame work wih 20x25mm 'T' and 20x20mm 'L' section with grid size of 605x605mm including with necessary 3.15mm GI wire as in suspended etc complete all as specified and as directed by Engr-in-Charge.

S&F Gypsum ceiling board 60x60cm x8mm thick (pre-finished decorative type) in ceiling fixed with screw as per manufacturers instruction, or complete all as specified and as directed by Engr-in-Charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for window grills etc complete all as specified and as directed by Engr-in-Charge.

M&L steel work in roof trusses (framed)trussed, posts, purlins, crane gantries rails and fastenings and heavy bracket framing (beam, tee, angle channel or flat sections) including distance pieces cleats etc Fe-410 W (Gde - E-250) quality A complete all as specified and as directed by Engr-in-Charge.

S&F mild steel work as in band straps, supports or stays for rain water ,ventilating pipes, including bolts, if required; clamps , wall tie, hooks , angle cleats ,hold fast etc and similar small articles conforming to Fe 290, grade E-165 complete all as specified and as directed by Engr-in-Charge.

M&L Providing cement concrete 1:2:4, type B-1 using (20 mm graded aggregate) as in coping apex stones, bed plates, kerbs, slightly rounded or chamfered angles and throating complete all as specified and as directed by Engr-in-Charge.

M&L preparation of new untreated Steel surfaces of any description not otherwise described over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome complete all as specified and as directed by Engr-in-Charge.

M&L for complete removing existing treatment on steel surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and as directed by Engr-in-Charge.

M&L for complete removing existing treatment on wooden surfaces of any description, over 10 cm in width or girth not otherwise described and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed by Engr-in-Charge.

Taking down cement plaster on brick or concrete surfaces including racking out joints hacking for keys scrubbing down with water etc. complete all as specified and as directed by Engr-in-Charge.

Rendering 10mm thick on fair faces on brick masonary or concrete surfaces in cm 1:6 finished complete all as specified and as directed by Engr-in-Charge.

M&L for Prepration of newly plastered on walls by hand held sander / long handle sander including cornices, pilasters etc complete all as specified directed and applying two coat of oil bound distemper over a coat of alkali resistant priming paint, over a coat 3mm thick wall care putty on walls complete all as specified and as directed by Engr-in-Charge.

M & L rendering 15mm thick on brick wall or concrete surface consisting two layers of 5mm thick in cement mortar 1:4 over 10mm thick in CM (1:6) finished even and smooth with using water proofing compound complete all as specified and as directed by Engr-in-Charge.. (Note:- Water proofing compound shall be measured and paid saperately.)

Supply only water proofing compound complete all as specified and as directed by Engr-in-Charge.

M&L Prepration of newly plastered surface of wall by hand held sander / long handle sander including cornices, pilasters etc and appliying with Airless spray two or more coats of 100 % premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489-2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company Depot Tinted) with silicon additives @1.43 litre/10Sqm over and including priming coat of exterior primer applied @ 0.9 ltr/10sqm complete all as specified and as directed by Engr-in-Charge.

M&L complete removal of existing tretment by hand held sander / long handle sander washing down with Jet washer and appliying Airless spray two or more coats of 100 % premium acrylic emulsion paint having VOC less than 50gm/litre and UV resistance as per IS 15489-2004, Alkali & fungal resistance dirt resistance exterior paint of required shade (company Depot Tinted) with silicon additives @1.43 litre/10Sqm over and including priming coat of exterior primer applied @ 0.9 ltr/10sqm complete all as specified and as directed by Engr-in-Charge.

Complete removal of existing treatment of old surfaces of wall including preparation of surfaces by hand held sander / long handle sander including cornices, pilasters etc and applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 1 mm thick wall care putty complete all as specified and as directed by Engr-in-Charge.

Complete removal of existing treatment of old surfaces of wall including preparation of surfaces by hand held sander / long handle sander including cornices, pilasters etc and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed by Engr-in-Charge.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar complete all as specified and as directed by Engr-in-Charge. .

M&L Machine cut & polished Kota stone slab as in flooring, cill of window single piece over lap 18-20mm thick laid over screed base ,laid & ,jointed with grey cement slurry mixed with pigment to match the shade of the slab steps, jambs, pillars, window- cills, etc including 20mm thck screed bed in CM 1:3 complete all as specified and as directed by Engr-in-Charge.

Mirror polishing on marble/ granite/ Kota stone/ stone work where ever required to give high gloss finish complete all as specified and as directed by Engr-in-Charge.

M&L for screed bed or bedding 15 mm thick in CM 1:4 on floor to receive tile. complete all as specified and as directed by Engr-in-Charge.

M&L Vitrified ceramic tiles dark shade 8-10 mm thick (square/rectangular) polished, area of each tiles n exc 0.36 sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 15 mm thick screed bed in CM 1:4 complete all as specified and as directed by Engr-in-Charge.

M&L Vitrified ceramic tiles dark shade 8-10 mm thick (square/rectangular) polished, area of each tiles n exc 0.36 sqm in skirting etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over & including 10 mm thick backing coat in CM 1:3 complete all as specified and as directed by Engr-in-Charge.

M&L coloured Glazed ceramic tiles in vertical surface 450mm X 300mm X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match over & including 10 mm thick plaster in CM 1:3 complete all as specified and as directed by Engr-in-Charge.

Taking down chowkats with shutter (without taking off shutters from the frames) exc 1.5 sqm but n exc 4 sm each, complete all as specified and as directed by Engr-in-Charge.

S&F Anodised powder coating (minimum thickness of powder coating 50 micron) aluminium frame for doors of 1.50 Kg/Rm, anodised aluminium door shutters, aluminium section weighing 0.55 kg/m, 5.5 mm sheet glass,double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty,Jindal or equivalent duly fitted with neoprene beading, glazing clips, glass panes 12 mm nominal thickness aluminium alloy handles etc.complete all as specified and directed (Make: Jindal/Hindalco/Indal) NOTES: Rates include all joining ,locking arrengements,handles,door stoper,door closer etc Note -size of door varies from exc 1.5 Sqm and n. exc 4.0 sqm

Providing cement concrete type BO 1:2:4 (12.5mm graded aggregate) in cills, steps, seismic and other similar bands plinth coureses string courses lacing courses parapets and railing copings kneelers apex bed plates kerbs. etc.. water troughs and the like including wethering slightly rounded or chamfered angles and throating complete all as specified and as directed by Engr-in-Charge.

Demolition Cement Concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level complete all as specified and as directed by Engr-in-Charge.

M & L 75mm for PCC 1:2:4 type B2 (using 40mm graded stone aggregates) as in flooring, finished surface even & smooth without using extra cement laid to slope 1:12 in alternate bays each bay not exceeding 2.5m length, 10mm groove at junction of wall and plinth protection complete all as specified and as directed by Engr-in-Charge.

Forming construciton joints 30mm deep x 10mm wide filled with sealing compound grade 'B'. Complete complete all as specified and as directed by Engr-in-Charge.

S&F powder coated aluminium sliding window of 3 tire, frame of section 62mm X 32mm X 1.47 mm or appropriate equivalent section and shutters of section 18 mm X 44 mmX 1.35 mm or appropriate equivalent section fixed with 4 mm thick tinted sheet glass with rubber gasket, handles, locking arrangement and aluminium wire mesh incl making good jambs, cills etc and including taking down old iron window complete all as specified and directed by the Engr-in-Charge.(make: Hindalco/Indal/Jindal or equvalent)

S & F Framed work such as grills,gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165

M&L 16 to 18 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 20mm screed bed in CM 1:4 complete all as specified and as directed.

M&L Rounding to edges of 20mm thick granite slabs one edge,such as in window cill, cooking platform, and other similar situations including grinding polishing complete all as specified and as directed.

S&F in repair 25mm dia stainless steel curtain rail, cut in required length and size to fit with opening incl fixing on bracket with necessary screws fitted on bracket and decorative nobs on sides with necessary arrangement complete all as specified and as directed by Engr-in-charge.

S&F in repairs curtain rod side brackets of stainless steel, angular or cantilever type fixed to wall with 02 nos screws on each bracket and fitted screws for fixing curtain rod incl CP/stainless steel carved decorative design plain metal colour nobs with fixing arrangement for curtain rod using a screw complete all as approved and shown by Engr-in-charge.

M&L for racking of cracks ,preparation and crack filling with polymer modified/chemical based crack fillers by approved manufacturer and filling as per manufacturer instructions in walls,roofs of any type or size (Make: Pidilite/dr fixit,fosroc, or equivalent) all as specified and directed

(a)cracks up to 5 mm wide

(b)Cracks exc 5mm but not exc 10 mm

Removal of all loose/unsound/bad/damaged concrete or plaster existing RCC structure of slab/beams/walls/chajja by using chesel/hammar .Cut and remove unsound reinforcement bars, wires etc without damaging the sound reinforcement . clean loose rust from bars manually with brush . fixing new supplymentary bars if required,either by tying it with existing bars or by welding on it. Applying eppoxy bonding agent and making good with polymer modified plaster/micro concrete as required thickness over a coat of rust removing alkaline primer and match the finishing to the existing surface in ground floor including formwork complete all as approved and shown by Engr-in-charge.

Demolition of in lintels, chajja,manole cover landing,slab, parapet stair case of cement concrete reinforced of similar suspended works complete all as approved and shown by Engr-in-charge.

M & L RCC nominal mix type B1 1:2:4 using 20mm graded aggregate as in chajja, parapet etc and incl necessary formwork complete all as approved and shown by Engr-in-charge.

S&F TMT bars 10mm dia and over, cut to length, bent to shape required,including binding with mild steel wire (annealed) not less than 0.9mm dia. complete all as approved and shown by Engr-in-charge.

Demolition of Brickwork or stone/ boulder masonry built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles complete all as approved and shown by Engr-in-charge.

M&L brickwork with old size flyash bricks straight or curved on plan exc 6 m mean radius built in CM 1:6 complete all as approved and shown by Engr-in-charge.

Taking down copper /aluminium point wiring (light, fan, bell,socket or power) complete including fixture and fittings such as switches , ceiling roses , pendent , regulators, sockets, light fitting etc. Removing materials to store for keeping in safe custody or for taking credit (credit a for above items should be made as per condition seperately) and making good distrubed surfaces of walls, floors etc complete all as specified and directed at site. complete all as approved and shown by Engr-in-charge.

Taking down carefully copper/aluminium Sub main wiring of any size from surface/concealed /existing conduit of any height and removing materials at site and making good disturbed surfaces of walls, floors roofs etc complete all as approved and shown by Engr-in-charge.

Taking down ceiling fan/ Exhaust fan of any sweep after disconnecting all necessary electrical connections from ceiling rose to fan, fan blades and deposit to MES store yard of AGE E/M Jamnagar complete all as approved and shown by Engr-in-charge.

M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), two single core, PVC insulated and unsheathed FRLSH cable 1100 volts grade ISI-694 marked drawn through in and including heavy duty, PVC concealed conduit of white/ ivory colour including all accessories after chasing in wall/ceiling etc, heavy duty ISI marked, with GI sunken boxes 1.2 mm thick, 60 mm deep with earth dolly duly, covered with modular white cover plate with inner frame suitable for modular switches, including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLSH cable as earth continuity conductor to common earth and connecting to earth dolly including cutting, chasses and making good disturbed surface to match with existing finish with plaster complete all as specified and directed for the following :-

(a) One light point controlled by one, one way switch 5 Amps

(b) One fan point/ exhaust fan point controlled by one, one way switch 5 Amps and regulator

(c) One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board.

(d) One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad.

Description all as per item No 52 here in before but using 2.5 sq mm single core copper conductor cable of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for 15 amps switch socket cobmination point including necessary running of 2.5 sq mm copper conductor flame retardant PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly. (power point)

Description all as per item No 52 here in before but using 4.0 sq mm single core copper conductor cable of multistranded flame retardant PVC insulated unsheathed 1100 volts grade for 15 amps switch socket cobmination point including necessary running of 4.0 sq mm copper conductor flame retardant PVC wire as earth continuity conductor along with wiring and connecting to the common eath dolly. (power point)

Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and,cutting chases for concealed water,tubing or concealed conduit wiring,,etc., and making good, cutting not,exc 10 cm girth ®(stone massonary)

S & F for modular switch piano flush type, single pole, one way, and 5/6 Amp single module complete all as approved and shown by Engr-in-charge.

S & F for modular switch piano flush type, single pole, one way, and 15/16 Amp single module complete all as approved and shown by Engr-in-charge.

S & F for modular socket outlet multipurpose having provision for 3 pin, 5/6 Amp and 2 pin, 5/6 Amp, 2 module piano flush type complete all as approved and shown by Engr-in-charge.

S & F for modular socket outlet multipurpose having provision for 3 pin, 15/16 Amp and 3 pin, 5/6 Amp, 2 module piano flush type complete all as approved and shown by Engr-in-charge.

S & F for modular step type fan regulator (BLDC) 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as approved and shown by Engr-in-charge.

S&F ceiling rose surface backelet ISI marked 2 to 3 terminal complete all as specified and directed by Engr-in-Charge.

S & F for metal clad box suitable for 230 volt 50 Hz AC supply three pin with MCB SP 20/32 Amps including removal of old unserviceable one complete all as specified and as directed complete all as approved and shown by Engr-in-charge.

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 4 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 4.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 4 sqmm cable,one run of 4 sqmm cable and one run of PVC conduit will be measured as one unit

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLSH cable with stranded copper conductor of size 4 Sq mm nominal area and drawing into suitable size of PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked heavy duty of suitable size including concealed in wall etc one run of PVC insulated with 4.0 Sqmm (nominal area) stranded copper conductor FRLSH cable as earth wire complete all as specified and as directed. Note:- Two runs of 4 sqmm cable,one run of 4 sqmm cable and one run of PVC conduit will be measured as one unit

S & F for sheet metal enclosure MCB DB TPN 4 way with 200 Amps rated bus bar 415 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as approved and shown by Engr-in-charge.

S & F for sheet metal enclosure MCB DB SPN 8 way with 200 Amps rated bus bar 240 volts double door with magnitic locking system including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as approved and shown by Engr-in-charge.

S & F for MCB Tripple pole and neutral rated capacity 63 Amps, 415 Volts breaking capacity 10 KA, 'C' curve complete all as approved and shown by Engr-in-charge.

S & F for MCB Single pole and neutral rated capacity 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as approved and shown by Engr-in-charge.

S & F for MCB Single pole rated capacity 5 to 32 Amps, 240 Volts breaking capacity 10 KA, 'C' curve complete all as approved and shown by Engr-in-charge.

S & F for ceiling fan, 230 Volts, 1200 mm sweep with mian air delivary 210 CFM, service value of the fan shall be greater than 6.1 (5 star rated) as per BIS with blades, down rod & other necessary accessories with brushless direct current motor (BLDC) with out remote system and electrical connections from ceiling rose to fan teriminal complete all as approved and shown by Engr-in-charge.

S & F for energy efficient exhaust fan of 230 mm sweep made of metal body Ventil Air -DS type complete with louver with bolts nuts and washers size of the bolt 15 cm long 12 mm dia embedded in the wall including provision of PVC flexible copper cable of size 23/0.0076 two core from ceiling rose to exhaust fan for connection and making suitable size of hole to existing brick wall for fan base compelte all as specified and directed. (Note : Cost of suitable opening wall for fixing exhaust fan is deemed to be included in overall rate quoted).

Supply and fixing LED luminaire 600 mm x 600 mm, 35/36 watt, 220 V AC recessed type with high efficiency PMMA diffuser soft glare free light complete with driver, holders & LED lamp suitable for roof ceiling including connecting up with driver three core flexible copper conductor cases of suitable size complete all as approved and shown by Engr-in-charge.

S & F for Energy saving new generation environmental friendly long life versatile presure die cast aluminium IP 66 for security light fitting luminaire with high power LEDs as light source and electronic driver of capacity 25/35 watts with pre wired and necessary mounting arrangements and provision of 2.5 sq mm three core copper conductor cable multi stranded from ceiling rose to light fitting including necessary dia GI pipe medium grade bracket 1.5 mtr long bend to required shape with clamps, nut, bolts complete all as directed by Engineer- in-charge. Make :- Bajaj Cat part No ENXT P 24L WH CR PC SD (Edge plus series) or its equvalent in Philips, Wipro.

S & F for wall mounted LED tube light fitting 20 watts batten for surface mounted, anodized extruded aluminium housing, high transmissitivity diffuser, high lumen ouput box type fitting, 230 volts and intregrated electronic driver connector block etc with warranty option of 5 years from date of installation complete with all accessories internally pre wired and necessary mounting arrangements, provision of new 3 core multistranded copper conductor of size 23/0.193 from ceiling rose to fitting complete all as specified and as directed. Make :- Make Bajaj Cat part No BCLAB 20W WH LED P, Wipro Cat part No LL20-281-XXX065-ALI or its equvalent in Philips, Havells.

Labour only for refixing the exaust fan obtained from item No 4 above with replacement of unsv 3 core PVC insulated PVC sheated 3 core multistranded copper conductor cable of size 23/ 0.193 from ceiling rose to fan terminal including over hauling the fan, painting complete with two coats synthetic enamel paint by spraying including filling cavities with filler after cleaning all dust etc. complete all as approved and shown by Engr-in-charge.

sanu enterprise (BID ID -3499832)

Suraj Builders (BID ID -3505902)

ABR Trading Co (BID ID -3505837)

badri glass and construction (BID ID -3504991)

M/S Badri Electicals (BID ID -3499781)