PALLIKUNNU LIFT IRRIGATION ,ELECTRIFICATION ,ACCESSORIES

Amount

PART I Supply and erection of motor pumpset supply of horizontal split casing pump with CI casing CI impellar steel shaft etc in standard construction capable to discharge 56 LPS of clear water to a head of 42 metres coupled with 37 KW/ 50 HP 1475 RPM 3 phase TEFC sq cage induction motor mounted on fabricated base frame, coupling guard etc complete including all taxes (Make of pump prefered: Kirloskar/ Jyoti/ Mather platt.) makes of motor prefered - Kirloskar/ Jyoti/ Crompton/ ABB etc .

Supply of Kirloskar brand DV 40 vaccum pump set coupled with 3 phase 5 HP sq cage induction motor complete base frame coupling, coupling guard etc inclusive of all taxes.

supply of oil cooled auto transformer type starter with overload and under voltage protection for 50 HP, 3 phase sq cage induction motor 1450 RPM (make prefered Jyoti/ Kilburn/ Bee Bee)

Excavation for foundation in soft soil including dressing of sides and ramming of bottoms, lift upto 1.5 m including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 metres.

Providing and laying in position cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc as required.

Providing and laying in position cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) in foundation of pump, DG set etc including form work etc as required.

supply and providing MS foundation bolts suitable for above motors

Providing 15mm thick cement plaster of mix 1:4 (1 cement : 4 fine sand) at all levels.

Charges for erction of 50 HP motor pumpset with base frame over the foundation block in correct alignment , setting tight foundation bolts as required.

charges for erection 5 HP motor pumpset with base frame over the foundation block in correct alignment. Setting the foundation bolts as required

charges for fabrication supply conveyance and installation by jointing 150 mm dia MS pipe with necessary MS flanges jointing the same in required alignment using rubber gasket iron bolt and nuts etc in leak proof condition and painting the same with 2 coats of syn. Enamel paint over a coat of red oxide primer for deliver line

charges for fabrication supply conveyance and installation by jointing 200 mm dia MS pipe with necessary MS flanges jointing the same in required alignment using rubber gasket iron bolt and nuts etc in leak proof condition and painting the same with 2 coats of syn. Enamel paint over a coat of red oxide primer for deliver line

charges for fabrication supply conveyance and istallation by jointing 200 mm to 150mm dia fabricated MS reducer of 0.30 long with necessary MS flanges including painting as above.

charges for fabrication supply conveyance and istallation by jointing 150 mm to 100mm dia fabricated MS reducer of 0.30 long with necessary MS flanges including painting as above.

charges for fabrication supply conveyance and istallation by jointing 200 mm dia bend of 0.75 long with necessary MS flanges including painting as above.

charges for fabrication supply conveyance and istallation by jointing 150 mm dia bend of 0.75 m long with necessary MS flanges including painting as above.

Fabrication supply conveyance and installation of angle frame for wall mounting panel board and support

charges for supply conveyance and installation of 150mm dia heavy duty CI sluice valve in position

charges for supply conveyance and installation of 150mm dia heavy duty CI non return valve in position

charges for providing priming arrangements to HS pump using 20 mm dia PVC flexible hose GI barel nipple hex nipple GI socket and 20 mm GM gate valve etc.

Part II Power wiring fabrication supply conveyance and instalation testing and commissioning of floor or wall mounting dust and vermin proof cubicle type MV panel board comprising of the following components / device & complying to IS 8623

Fabrication of fully partitioned, dust and vermin proof enclosure for panel assembly as per form 4 of IS 8623 (with latest amendments) design and requirement, with front and rear access facility, bus bar chambers, hinged doors for all switch gear compartments, earthing the doors using 4 sq mm braided copper conductor, providing necessary cut-outs for mounting meters, relays, indication lamps, bus bar interconnection etc, detachable covers for bus bar chamber and cable alley, powder coating the assembly after subjecting to 7 tank process etc as required. CRCA sheet alone be used for the fabrication. Angles/ flats/ slotted angles etc shall not be used for the fabrication of panel assembly. The measurments should be taken the area of the complete sheets used for panel board including partitions, folding, shrouding etc. including control wiring (excluding base frame)

Supply and providing the following size of SMC sheets in the panel as barriers & shrouding using required bolts and nuts including cutting to shape etc., as required.

2 mm thick

Supply and fixing the following types of beeding along the periphery of doors/ other detachable compartments to make the panel assembly dust & vermin proof including sticking with glue

U' section rubber beeding suitable for 1.60/ 2.00 mm sheet

Supply Fabrication, , conveyance and installation of base frame of panel board using 75x40 mm rolled steel channel (ISMC)

Supply and providing copper busbars including finger type SMC busbar supports in the bus chamber, suitable size nut & bolt, providing heat shrink sleeves etc. as required.

supply and providing copper earth bus in the panel board.

Supply, conveyance and fixing the following types & current rated control gears & switchgears conforming to IS 13947 suitable for 440 V, 50 Hz, AC supply in the existing panel assembly as required.

250A, 50 kA (Ics=100%Icu), 4 pole, current limiting type MCCB with thermal magnetic release with setting of 50-100% having adjustable OL &SC>

Supply and fixing 1 number earth fault realy upto 125A to 200 A with CBCT

Supply and fixing shunt release for all voltage ranges upto 630 A MCCB

Supply and fixing one number under voltage release for all voltage range upto 630A MCCB

Supply and fixing rotary handles external type(including BUC handle with door interlock) in the existing MCCB upto 250A

32 Amp TP&N

160 Amp TP&N

LED indicators for all voltage ranges - red green black yellow or orange colour

S&F Digital multifunction meter to read V A F PF 3 phase accuracy class 1 LED

20A 415V HRC fuse base with fuse link

providing MV danger notice plate of 200mm x 150 mm made of mild steel at least 2mm thick and vitreous enameled white on both sides and with inscription in single red colour on front side as required

Supply and fixing the following sizes of PVC Conduit conforming to IS 9537 / 1983 part III along with all required accessories in surface/ recess including making cutting the wall and making good the damages etc as required.

20 mm dia light gauge

25mm dia light gauge

32 mm dia light gauge

Supply and drawing 650/1100 V grade PVC insulated stranded single core copper conductor cables conforming to IS 694 part I 1990 in the existing surface / recess conduit/ CMS as required including giving necessary connections of the following sizes.

16 sq.mm 4 Run

10 sq mm 3 run

2.50 sq mm 4 run

2.50 sq mm 3run

supply and clamping the following sizes of PVC pipe on wall with all required accessories including cutting and making good the walls colour washing etc

40 mm dia PVC pipe (8kg/cm2)

Supply of superior quality copper tubler cable socket and making core termination of copper cable of the following size including crimpling etc as required

16 sq mm socket

10 sq mm socket

2.5 sq mm socket

Charges for supply and instalation of 160A TPN isolator fully automatic star delta starter 18 kvar 3 phase 440V delta connected standard duty metalised poly propylene capacitor cylindrical type suitable for direct connection to motors over MS frame work making connection as required.

supply and instalation of 3 phase DOL starter for 5 HP vacuum pump 32A TPN isolator and 3 Kvar 3 phase 440V delta connected standard duty metalised poly propylene capacitor cylindrical type suitable for direct connection to motors over MS frame work.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal

Providing and fixing testing joint made of 2 no. strips as mentioned below of the following sizes provided on either side of the conductors with 4 nos of GI bolts, nuts check nuts and spring washers etc. complete as required (for down conductors).

2Nos 25x6 mm G.I. strip 150 mm long

providing and fixing 25 mm X 5 mm G.I strip on surface or in recess for connection etc as required.

Supply and laying bare earthing conductors of the following sizes laid 0.6 m below ground level including excavating trench etc. as required

3.15 mm copper conductor (10 SWG)

4.75 mm copper conductor 6 swg

Supply and drawing bare earthing conductors of the following sizes along with wiring/ cables and giving connection as required

2.00 mm copper conductor (14 SWG)

2.65 mm copper conductor (12 SWG)

3.15 mm copper conductor (10 SWG)

4.75 mm copper conductor (6 SWG)

Supply of superior quality copper earth sockets for the following sizes of earth conductor including crimping etc. as required

2.00 mm copper conductor (14 SWG)

2.65 mm copper conductor (12 SWG)

3.15 mm copper conductor (10 SWG)

4.75 mm copper conductor (6 SWG)

Supply and providing the following sizes of bolt and nut with washers on the existing M.S box/ earth bus etc. as required including drilling necessary holes as required

25x3 mm brass bolt & nut

25x6 mm brass bolt &nut

Supply , threading, laying and jointing of the following sizes of '' B'' class G.I. pipe all required accessories in ground in the existing trench as protective covering to earth leads.

15 mm dia

Supply, laying and clamping of 1 no. PVC insulated and PVC sheathed armoured aluminium power cable, 1.1 KV grade of the following sizes using clamps noted along with the cables, spacing of clamps not exceeding 60cms, making good the damages , colour washing etc. as required.

3.5 core 95 sq mm with factory made clamp

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed XLPE

3.5 x 95 sq mm (45mm)

Part III Light wiring Supply and wiring points according to IS 732-1989 using rigid PVC conduit of minimum size 20 mm with specials conforming to IS 9537 part III 1983 and with suitable size specials conforming to IS 3419-1988, fixing the conduit using metal saddles spacing not exceeding 50 cm or concealed suitably and with 1.00 sq mm FR PVC insulated stranded single core copper conductor cable 650V grade, including providing switch board main and continuous earthing with No.14 SWG bare copper,required quantity of copper earth socket, brass bolt and nut crimping/ soldering etc complete with suitable size modular type metal switch boxes, modular type front plates (white) etc. up to and including 6A modular type SP switches and making good the surface of wall, colour washing etc. complete. All the terminations in the switch boards and DB's shall be tinned and the wires shall be drawn and fixed along the periphery of the box using suitable ties, tie mounts etc as required. (Group B/ RoHS compliant modular accessories).

Single Control light point with 6A, 3 plate ceiling rose - Short point

Supply, conveyance, installation, testing and commissioning the light fittings of following types made from 0.5mm CRCA sheet complete with all accessories and lamps etc. directly on wall using 2 nos. 'C/U' brackets made from 20 x 3 mm MS flat, painting the flat iron bracket and giving connections with required length of 16/0.20mm 3 core copper conductor flex wire conforming to relevant ISS or extending the original wiring and giving connection etc. as required.

1200 mm 1X20W LED Lamp with box type fixture

Supply and fixing cast aluminium stove enameled bulk head fitting with deep drawn anodised aluminium body, epoxy powder coated, heat resistant prismatic glass cover suitable for 9 W CFL to wall / ceiling including giving connections with required length of 16/0.20mm PVC insulated and PVC sheathed 3 core round copper conductor flex wire conforming to relevant ISS or extending the original wiring and making good the surface as required.

Supply and providing the following types and power rated lamps in the existing fittings as required

Normal size 11 W BC / ES retrofit CFL /LED

Combined plug point with 6 A, 5 pin plug socket controlled by 6 A switch in the same switch board as that of light points.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc as required.

3 Module (100x75 mm)

15/16A amps switch

6 pin 15/16A amp socket outlet

Supply Conveyance, installation, testing and commissioning of 36/40W LED street light output greater than 105 lumen/W 4000-6000 K with IP 66 protection LED Chip make Cree/ Lumilled/ Nichea with power factor greater than 0.95 at full load, internal surge protection up to 8 KV,and Aluminium pressure die-cast Powder coated housing,acrylic cover complete with THD Less than10%, power factor greater than 0.98, RoHS compliant, duly wired up for use on 230 V AC supply. Driver compartment should be seperatly accessible for maintenance (LM 79&80 certificates from NABL accredited Third party lab to be produced mentioning chip manufacturer)

Supply, fabrication, conveyance and fixing the following sizes of B class GI pipe bent to shape/ cut and welded to shape and fixing the same to wall / parapet using clamps as noted along with each size, painting with 2 coats of synthetic enamel paint over a coat of zinc chromate primer, making good the damages, colour washing etc as required - (for installation of outdoor light fittings)

25 mm dia with HG company fabricated clamps

Fabrication supply and installation of dust and vermin proof wall mounting hot press moulded SMC meter box of following size suitable for forming KSEB meter fuse units CT etc hinged door connections for the front side with compartments if necessary providing vision panel for the meter compartment knock out for cable entering and exit

GS-MB 7450 (inside 700x480x200 mm)

GS-MB 3525 (inside 350x250x150 mm)

Supply and fixing the following accessories in the existing meter board and giving connection as required

250 A HRC fuse base with HRC fuse link

20 A HRC fuse base with HRC fuse link

250 A 415V, 2 way neutral link mounted on DMC / SMC base

32 A 415V, 2 way neutral link mounted on DMC / SMC base

switch disconnector unitm32 A DP AC 23 A

Supplying and fixing following way single pole and neutral , sheet steel , MCB distribution board 240 Volts, on surface/ recess, complete with tinned copper bus bar , earth bar, din bar, inter connections, powder painted including earthing etc. as required. (But without MCB/RCCB/ isolator)

2+6 way double door single phase

25A double pole mini break isolator

25A 2 pole volts 30mA RCCB

S&F 6A 32A SPMCB (C curve)

2.00 mm thick 3.3 KV Sy Electronic fire retardant insulating sheet

supply and providing 5 kg dry chemical powder type fire extinguisher with hose clamps including fixing it to wall as required.

supplying and providing 9 litre capacity GI fire bucket painted in post office red with primer coat of red oxide and written with white paint FIRE mentioned on MS angle frame work/ wall bracket filled with fine sand painting the bracket / floor steel including making good the damages colour washing etc as required

KSEB test report

SRISAKTHI ELECTRICALS

PONNU HYLINE