Loading…
Loading…
Tender Value
₹4.0 Cr
EMD Value
₹7.9 L
Closing Date
15 Jun 2026, 3:00 pm
S&T work in connection with: Provision of Model Room in MDZTI/BSP.
06-ST-Tender-2026
06-ST-Tender-2026
Open
12 Months
Unknown (Unspecified Location)
₹0
₹7.9 L
23 May 2026
23 May 2026
1 Jun 2026
Item Breakup - A-Execution of Work
Design of detailed Circuit & Wiring Diagram Station for Electronic Interlocking system with Automatic Block Signalling/IBS/Absolute SL,DL Section The sections will be arranged in the manner:- (1) A to B: Automatic Double Line Section (2) B to C: Automatic Single Line Section (3) C to D: Absolute Single Line Section (4) D to E: Absolute Double Line Section With provision of IBS etc. as per the prevailing interlocking practices in SECR/as advised by the railway representative on the basis of approved Signalling Interlocking Plan (SIP) including the preparation of SIP, SWRD (as per attached Sketch plan) & preparation of other relevent documents & drawing. (Note: Approved design to be submitted in Polyester Film Tracing with 6 Ferro copies of each station. Soft copy of Design and Circuits diagrams should also be supplied in CDs/Pendrive (2 Copies) in editable software).
Supply & Installation of Track Circuit Numbers materials required for Model Station. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply & Installation of O/E/N Relay Rack Numbers with scaffolding materials & required hardware & erection materials to accommodate the required no of relays. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply and Installation of Cable Termination Numbers Rack with scaffolding materials; ladder for supporting outdoor cable; wire guide; complete with other necessary hardware's as per requirements of Rly. & erection materials. (Rate & Station Wise Qty. to be specified by the tenderer.) 1) Upto 4 to 5 Line Station. Inspection by Rep. of Sr.DSTE.Co./BSP.
Supply and Installation of PVC Cable Duct of Numbers 45 mm X 45mm size and 1 Mtr. length with suitable cover. Inspection by Rep. of Sr.DSTE.Co./BSP.
Painting or varnishing of each model station Job & concern section with two coats of standard quality paints after one coat of primer.
Installation, Testing & Commissioning of Station Electronic Interlocking Unit upto 100 Routes along with Slip Siding, Catch Siding Automatic Block Signalling suitable for Model Room.
Supply & Installation of All Legend Boards Station required for the Model Station. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply & Installation of OHE materials & Metre accessories required for Model Station. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply and Installation of miniature type Numbers Electric Level crossing Gate. (operating voltage 12 VDC) suitable for Model Station. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply and Installation of miniature type Numbers Mechanical Level crossing Gate. (operating voltage 12 VDC) suitable for Model Station. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply and installation of Passenger & Goods Numbers Platform suitable for Model Station. Inspection by Rep. of Sr.DSTE.Co./BSP. BILASPUR DIVISION-S AND T/SOUTH EAST CENTRAL RLY
Miscellaneous Installation & Commissioning of Model station. Inspection by Rep. of Sr.DSTE/Co./BSP.
Installation of Axle counter sensor.
Supply & Installation of basic material to Numbers construct unit maintenance free earth as per RDSO Specs. No. RDSO/SPN/197 Ver. 1.0 or as per RDSO TAN 2025 to achieve a resistance less than 1 ohm. It consist of following: (a) Copper bonded steel electrode of minimum 3.0 meter long, minimum 17.0 mm dia with copper bonding thickness of minimum 250 microns and UL listed and marked = 1 No. (b) Earth enhancement material supplied in sealed bags of minimum 10 kg = 3 Nos. (c) Copper strip of 200x25x6 mm, to terminate earth rod = 1 No. (d) Copper strip of 300x25x6 mm (MEEB) 1No. (e) Copper strip of 150x25x6mm (SEEB) = 1 No. (ii) Supply of 35sq. mm multi strand single core PVC insulated copper cable as per IS:694 for connecting main earth electrode to MEEB in the equipment room- with 4 Nos. (minimum 10 meter.) (iii) Supply of 16 sq. mm multistrand single core PVC insulated copper cable as per IS: 694 for connecting MEEB to SEEB and SPD to MEEB (minimum 10 meter. ) (iv)Supply of 10 sq. mm multi strand single core PVC insulated copper cable as per IS: 94 for connecting various equipment to SEEB (v) Supply of copper lug sleeve for 3/16 cable Inspection of material by RDSO
Supply Commissioning of 10 KVA UPS. The UPS must have 1 hour battery backup in full load condition complete with all accessories as per specification attached in Annexure "I". Make: NUMERIC/ APC/ MICROTEK or similar. This also includes supply of one battery rack and one set (for input and output) compatible MCBs complete with cover & fixing materials. Make: Havells, Anchor or similar. Inspection by Rep. of Sr.DSTE/Co./BSP. Note: All the accessories including batteries + batteries rack etc. required for this installation is to be supplied by contractor within the same rate.
Supply, Installation and Commissioning of Numbers On-line UPS with Capacity of 5 KVA along with complete set of compatible batteries. It should be as per technical specification attached as Annexure "II". Make: APC/Uniline/Emerson . Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply, Commissioning of Voltage STABLIZER, It should be as per make and model i.e SVC- 10000 VA, MAKE STUDIO MASTER 10KVA/10000 W or Equivalent OR better/higher may be acceptable. Compatible for operation of PA system devices. Inspection by Rep. of Sr.DSTE/Co./BSP.
Provision of civil work in connection with Lumpsum cutting of tiles/wall for laying of cables/pipes and networking/electrical work for concealed wiring.
Installation and Commission of Block Proving Pair with Digital Axle Counter. BILASPUR DIVISION-S AND T/SOUTH EAST CENTRAL RLY
Installation & Commissioned of Block Proving Pair by Axle Counter (BPAC).
Supply & Installation of 36 inch multi Numbers function Design Jet printer similar to the HP model no T2600 having in build features scanner, copier, e-print capability with accessories 5NB95A Smart Tracker USB for Design Jet 3-in Core Adapter, Design Jet 36-in Spindle USB 3.0 to Gigabit LAN Adapter 180 A1/hr, 19.3 sec/A1(1) Ethernet; Wi-Fi, Make/Model: HP Designjet plotter T2600 or higher. Warranty Period : Upto 12 months from the date of supply. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply & Installation of Standard Throw (0.91 Numbers to 2.5) Multimedia Projector (MMP) With 1920 x 1200 (WUXGA) Resolution, Brand: BenQ or Similar, detailed specification is attached as Annexure "III". higher version are acceptable inspection by Rep. of Sr.DSTE/Co./BSP.
Supply and Installation of Grand vision Wall Numbers Mounting Projection Screen Size of 150" diagonal (8 X 10) along with Projector roof Mounting kit consisting of 15 Mtrs HDMI Cable and 15 Mtrs Power Cable Make: Grand Vision or Similar. Accepted Make. GRANDVISION / FALCON. Warranty Period : Upto 12 months from the date of supply. inspection by Rep. of Sr.DSTE/Co./BSP. Total 9833502.74
Item Breakup - B-Supply of Materials
Supply of simulated Electronic Interlocking Station Unit upto 100 Routes with provision of Slip Siding, Catch Siding, Automatic Block Signalling/IBS Absolute SL, DL Section. The sections will be arranged in the manner:- (1) A to B: Automatic Double Line Section (2) B to C: Automatic Single Line Section (3) C to D: Absolute Single Line Section (4) D to E: Absolute Double Line Section suitable for Model Room Station as per attached Sketch Plan. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of following MACLS Signal post Numbers suitable for Model Station- 4 Aspect miniature Signal unit with ladder post & LED etc. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of following MACLS Signal post Numbers suitable for Model Station- 3 Aspect miniature Signal unit with ladder post & LED etc. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of following MACLS Signal post Numbers suitable for Model Station- 2 Aspect miniature Signal unit with ladder post & LED etc. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of following MACLS Signal post Numbers suitable for Model Station- Calling-ON Signal Unit with LED etc. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of following MACLS Signal post Numbers suitable for Model Station- Route Indicator Signal Unit with LED etc. Inspection by Rep. of Sr.DSTE/Co./BSP. BILASPUR DIVISION-S AND T/SOUTH EAST CENTRAL RLY
Supply of DEAD END at required places Numbers suitable for Model Station. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of STOP Boards at required places Numbers near Railway track suitable for Model Station. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Hand point Machine with all fittings Numbers for point operation suitable for Model Station. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply Electric Point unit with all fixtures and Numbers fittings for proper point operation suitable for Model Station. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of 48 mm gauge Brass Rail along with Metre Sleeper & other materials etc. required for Model Station. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Guard Rail-12"" required for Model Numbers Station. Inspection by Rep .of Sr.DSTE/Co./BSP.
Supply of Switch Rail-12" & its accessories Numbers required for Model Station. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Table top Grass Board 12mm Numbers (4'X8') or MDF or water proof plywood of size 6'X8' or better and fixing on the table frame already provided/available at site. as per the advised by consignee. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Plug in type Miniature O/E/N Relay Numbers (3CO) with plug Board & Retaining Clip for Lamp Proving (ECR). Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Plug in type Miniature O/E/N Relay Numbers (3CO ) with plug Board & Retaining Clip for Route indication (UECR). Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Plug in type Miniature O/E/N Relay Numbers (4CO) with plug Board & Retaining Clip. Inspection by rep. of Sr.DSTE/Co./BSP.
Supply of Bus Bars fitted with Insulators. Numbers Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Paper base hylum Sheet of 12mm Numbers thick (4' X 4'). Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of PVC Wire coil of size as per Numbers instruction of site engineer in 100 mtr coils. Spec.no. IRSS-76/89. Material to be procured from RDSO approved firm only with performance guarantee. Inspection by Rep. of Sr.DSTE/Co./BSP. Note: Unit Number should be understood as coil (16/0.2 mm)
Supply of PVC Wire coil of size as per Numbers instruction of site engineer in 100 mtr coils. Spec.no. IRSS-76/89. Material to be procured from RDSO approved firm only with performance guarantee. Inspection by Rep. of Sr.DSTE/Co./BSP. (Note: Unit Number should be understood as coil) (2.5 Sq.mm)
Supply of PVC Wire coil of size as per Numbers instruction of site engineer in 100 mtr coils. Spec.no. IRSS-76/89. Material to be procured from RDSO approved firm only with performance guarantee. Inspection by Rep. of Sr.DSTE/Co./BSP. Note: Unit Number shouldbe understood as coil (7/0.2 mm) BILASPUR DIVISION-S AND T/SOUTH EAST CENTRAL RLY
Supply of Wago terminal 2-conductor Numbers 1500.00 disconnect terminal block for test and measurement 0.08 mm sq 2.5 mm sq centre marking with test slot for test plug. Carrier rail din 35, front -entry, cage clemp connection. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Steel carrier rail 35x 7.5mm, Numbers 1mm/0.0039 inch thick unslotted. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of End and intermediate plate 2.0 Numbers mm thick. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Screw less end stop, 6 mm thick Numbers unslotted. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Electric Engine (Working Model) Numbers suitablefor 48 mm gauge track including 1 No extra coach with each engine for the ZTC model layout. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Wago fuse conductor. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Axle counter sensor. Inspection of Pair Rep. of Sr.DSTE/Co./BSP.
Supply of UTP CAT-6 cable of reputed make Metre Siemen/Systemax/ DLink/ Tyco/ Krone/ AMP or similar. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Tool Kit Box as per technical Set specification. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Computer Table (1200 x 600 x Set 750) ; 1 no. with block board & Sunmica top and Chair steel cushioned 2 Nos. (Godrej) make or similar with all accessories and fixing materials to the consignee store, and transportation to the site. Note: One set includes one table and two chairs. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of 65 inch Android Smart Television Numbers with Direct LED Specification: Make & Model : equivalent to SONY Make, model-65X82L HDMI Ports : 04 Nos. USB Ports : 02 Nos. Ethernet Ports : 1 No Built in Wifi: YES Composite input :YES Component Input :NO RF Input :YES Built in setup Box :NO Details of Accessories :Remote Control, Connecting Cables, Batteries Screen Size :65 Inch Resolution (Pixels) :(3840x2160) UHD Category :Smart Operating System :Android Digital Audio output : YES HDMI ARC -YES Backlight Type : Direct LED Built in Mic - YES Screen Mirroring :YES Mount Type :Both Table and Wall mount Inbuilt speakers :YES Wattage of Speakers -10Wx2 Subwoofer :No Warranty :1 years Type of Display Technology :Direct LED Only OEM/authorized dealer to be participate in the bid and concerned documents to be submit along with bid Accepted Make/Brand - Sony. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Smart Television TV 75 Inch LED Numbers Backlit LCD, Make/Brand: SAMSUNG,LG,Sony or Similar. Detailed specification is attached as Annexure "IV". Inspection by Rep. of Sr.DSTE/Co./BSP. BILASPUR DIVISION-S AND T/SOUTH EAST CENTRAL RLY
Supply of Smart Television TV 85 Inch LED Numbers Backlit LCD, Make/Brand: SAMSUNG,LG, Sony or Similar. Detailed specification is attached as Annexure "V". Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Digital Multi Meter Make: Fluke Numbers Model No. 287 complete or similar equivalent or higher version may be acceptable. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Electrical extension board with Numbers complete set. It contains Minimum five Numbers Female type socket, rating: 5Amp, operation-able by single switch rating 5 Amp. Connected cable length to be minimum 1.5 meter. Inspection by Rep. of Sr.DSTE/Co/BSP.
Supply of Media Converter. It should be as Pair per technical specification on Annexure "VI". Make: Team Engineer, MROtek or Syrotech. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Automatic Media changeover of Pair UFSBI working on redundant channels for data transmission on OFC/Quad. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of 4 Port, -48V DC Router 3 LAN port Numbers & 4x2 mbps G-703 port, RAM-512 MB or higher as (installed) /8MB (max) & Flash memory minimum 256MB (installed),power supply card(-48 V)DC operated ,(rack mountable- modular - 2U) as per RDSO specification No. RDSO/ SPN /TC/84 /2008 Rev0 or latest specification. Make: Cisco 2900 or 3900 series or HP or Juniper with similar or Higher configuration. Accepted: Cisco 2911 /2921/2951 with DC power supply. Warranty Period : Upto 30 months from the date of supply. inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Rectangular CENTRE TABLE of high Numbers quality material and premium finish , Brand: space wood or similar or better. Detailed specification to be obtained from the consignee as per the requirement at site. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Push Button Telephone with caller Numbers ID facility & reset box (RJ-11). It should be as per technical specification on Annexure "VII". Make: Beetel, Panasonic, Uniden or similar. Inspection by Rep. of Sr.DSTE/Co./BSP. Remarks: Before supply of the material, consent from consignee to be obtained.
Supply of Rodometer [Analog] Spec: Numbers Mechanical 5 digits counter, ABS Plastic wheel with rubber tyre, measure Forward & Backward, Telescopic handle, Precision measuring wheel. Make/Brand: Freeman. Warranty Period : Upto 30 months from the date of supply. inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Block proving with Digital Axle Pair Counter as per RDSO Spec No: IRS S 105/2012 or latest amendment, using UFSBI and Block panel for single line operation. (This includes list of enclosed Spares, Two Additional Modems for 6 Quad/OFC and Two Auto Changeover Modems for each Pair). Warranty Period : Upto 30 months from the date of supply. Inspection by RITES. BILASPUR DIVISION-S AND T/SOUTH EAST CENTRAL RLY
Supply of Block Proving by Axle Counter Pair (BPAC) using block panel and UFSBI double line operation as per RDSO Spec. No:IRS- 105/2012(VER.0) with latest version and amendment. Each set consisting of following (1) Universal Fail Safe Block Interface complete with all accessories as per RDSO Spec: No: IRS-S-104/212(ver.0) with latest version & Amdt - Qty-02 Nos. (2) Block Panel complete with all accessories as per RDSO Drg. No:RDSO/S/32017 (latest amdts.) Qty 2 Nos. (3) Relay Rack duly wired with due locking and sealing arrangement as per RDSO Drg. No: RDSO/S/32018 Including relays for each Relay Rack (QN1-19 Nos ,QNA1-07 Nos ,QL1-02 Nos. and Timers-01 No) - Qty 2 Nos. (4) Block Telephone with accessories as per RDSO spec. No: RDSO/SPN/191/2006- Qty 02 Nos and applicable spares shall be supplied. Warranty Period : Upto 30 months from the date of supply. Inspection by RITES.
Supply of Industrial Grade Embedded PC with Numbers Printer and 55 Inch VDU monitor. Specification should be in accordance with Para 5.3 (5.3.1 & 53.3.2) of RDSO specification RDSO/SPN/192/2019 Ver 2.0 or latest as per guidlines issued by RDSO. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of various types of relays, including Lumpsum miniature relays, required for commissioning and smooth execution of the work, as per the instructions and site requirements communicated by the Rep. of Sr. DSTE/Co./BSP. Inspection by the Rep. of Sr. DSTE/Co./BSP."
Supply, Commissioning of LAPTOP (Notebook) with complete accessories as per technical specification on Annexure "VIII". Make: HP, Lenovo, Dell or similar. Remarks: Before supply of the material, consent from the consignee to be obtained. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply, Commissioning of All-In-One PC with latest configuration. It should be as per technical specification on Annexure "IX". Make: HP, Dell or Lenovo. Remarks: Before supply of the material, consent from consignee to be obtained. Inspection by Rep. of Sr.DSTE/Co./BSP.
Supply of Maintenance Console with i7 Numbers processor or higher. It should be as per technical specification on Annexure "X". Make: HP, Dell or Lenovo. Inspection by Rep. of Sr.DSTE/Co./BSP. Total 29787443.73
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
06-Annexures_4.pdf
ATTACHMENT
Annexure-VandVA.pdf
ATTACHMENT
Annexure-VIB-TurnoverData.pdf
ATTACHMENT
Annexure J
ATTACHMENT
Annexure-J-RetiredRailwayEngineerFormat.pdf
ATTACHMENT
Download all tender documents and submit your bid