Repair/Replacement /Maint of E/M Installation and allied B/R works at CPH at GE (AF) No.2 Jodhpur

Amount

Demolition of unreinforced cement concrete in ground floors and paving n.exc 15cm thickness(below or above ground level) complete all as specified and directed by Engineer-in-Charge.

Demolition of reinforced cement concrete in ground floors and paving n.exc 15cm thickness(below or above ground level) complete all as specified and directed by Engineer-in-Charge.

M & L for CC 1:2:4, type B-1 (volumatric mix) using 20mm graded crushed stone aggregate as in of roof Kerbsor mud stops,rounded or chamfered on edge etc complete. in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs not provided for in Item 04028, water troughs and the like including weathering, slightly rounded or chamfered angles and throating, as directed

M & L for precast cement concrete 1:2:4, type B0 using 12.5mm graded stone aggregate as in jallies 35 mm thick (measured solid ), incl all mouldings but excluding frame set in cement mortar 1:4.

S & F 8 to 10 mm dia mild steel TMT bars , cut to length ,bent to shape required including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.90mm dia complete.

Dismantling of sand stone/Kota stone slabs and tiles in flooring or on vertical surfaces etc of any description or thickness laid bedded and pointed in any mortar complete all as specified and directed by Engineer-in-Charge.

M & L sand Stone slab 25 to 35 mm thick, dressed True and squre in one length not less than 60 CM and n exc 120 CM in coping, window cill , chajjs, sunshed etc, punched dressed on exposed faces and self faced on the embeded unexposed bed and joints exposed edges rounded and chamfered as directed set jointed in cement mortor including screee 15 mm CM 1:6.

Supply only Jodhpur sand stone for lintels, beams and roofs, self faced, 7.5 to 10cm thick

Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete including 15 mm thick screed bed or bedding layer in CM 1:6.

Demolition of brick work or stone/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc but excluding ashlar facing dressed stone work and precast concrete articles complete all as specified and directed by Engineer-in-Charge.

M&L for PCC block masonary with solid blocks exc 10 cm in width 1:3:6 Type C1 20 mm graded aggregate and setting in mortar complete .

Taking down cement or cement lime plaster, any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed by Engineer-in-Charge

M & L 15 mm thick rendering on fair faces of brick walls in CM 1:4 , finished fair & smooth w/o using extra cement.

M&L for rendering 10 mm thick in CM 1:3 stone masonry surfaces finished even and smooth (without using extra cement).

M&L for rendering 15 mm thick in CM 1:6 stone masonry surfaces finished even and smooth (without using extra cement).

M & L 15 mm thick rendering on other than fair faces of brick walls in two layers, 1st layer 10mm thick in CM 1:6 and 2nd layer in CM 1:4 with using water proofing compound, finished fair & smooth w/o using extra cement.( WPC to be measured separately under respective item)

Supply only water proofing compound

M& L for Raking out joints/ pointing in cement mortar to to squared rubble masonry, coursed or uncoursed etc.

M&L Struck pointing to to squared rubble, coursed or uncoursed in CM 1:4

Dismantling floor, hearth or wall tiling, including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed by Engineer-in-Charge

M&L for Glazed COLOURED ceramic tiles in vertical surface 450X 300X 7mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match & rendering 10 mm thick in CM(1:4) all as specified and complete.

M & L Non skid Endura tiles of 300x300x12 mm thick, coloured in floor etc set and jointed in neet cement slurry and pointed in coloured cement to match the shade of tiles over 15 mm thick screed bed of CM 1:6 all as directed by Engineer in Charge. complete all as specified and directed by Engineer -in- Charge.

M&L for 25 mm thick PCC (1:2:4),typeB-1, using 20 mm graded stone aggregate as in floor complete all as spfd & directed.

Roughening surfaces of old concrete floor by picking, sweeping, and washing down with water to remove dust, etc.

M & L Setting coat 3mm thick in CM 1:3 trowelled to even and smooth finish over 10 mm thick rendering on fair faces of concrete surface in CM 1:4 , finished fair & smooth w/o using extra cement.

Wire brushing and cleaning top surface of tiles, lime terracing or cement concrete, including flashings and junction of parapets, etc., and surface painting, with a layer of blown grade bitumen of any penetration applied hot @ 1.7 kg per sq. m, blinded with grit or pea size gravel @ 0.006 cu.m per sq.m, and lightly tampered (area of flashings, etc., shall be added to the roof area)

M&L for preparing old plastered ceiling/soffits of chajjas surfaces and applying one coat of white wash complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of Old plastered surfaces of walls and applying one coats of white wash complete as spd & directed

M & L for preparation of Old plastered surfaces of walls and applying one coat of OBD complete as spd & directed

M&L for preparation of Old plastered surfaces of walls, Chajjas, etc and applying one coat of cement base paint of approved shade complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of old wooden surfaces of any description , not otherwise described ,over 10 CM width or girth and applying one coats of synthatic enamel paint .

M & L for preparation of old steel surfaces of any description not otherwise described over 10 CM width or girth and applying one coats of synthatic enamel paint.

M&L for preparing new plastered ceiling/soffits of chajjas surfaces and applying three coat of white wash complete all as specified and directed by Engineer-in-Charge.

M & L for preparation of new plastered surfaces of walls and applying two coat of White wash complete as spd & directed

M & L for preparation of new plastered surfaces of walls applying two coat of cement base paint of approved shade complete as spd & directed

M&L for preparation of new wooden surface over 10cm width or grith & applying two coats of synthetic enamel paint of 1st quality over a coat of pink primer complete all as spd & directed

M&L for preparation of new steel & Iron surface of width or grith exceeding 10cm & applying two coats of synthetic enamel paint of 1st quality complete all as spd & directed.

M&L for writing letters or figures (Block, Roman, Italic or Indian) n.exc 30 cm high using synthetic enamel paint Ist quality complete all as specified and directed.

M&L for writing Stops, commas, short lines, dashes, hyphens brackets etc using synthetic enamel paint Ist quality complete all as specified and directed.

Taking down Chowkats or frames with shutters (without taking off shutters from the frame) exc 1.5sqm but not exc 4 sqm each and removing from site complete all as specified and directed by Engineer-in-Charge.

S &F pressed steel door frame of size 125x60mm for doors with one or more rebates including nacessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

Taking down shutter of any description exc. 1 sqm but n.exc 2 sqm each and removing from site complete all as specified and directed by Engineer -in-charge.

S&F flush shutter 30 mm th solid core construction with block board core & ply wood face panels, commercial type on both side.

M & L for easing of steel rolling shutters of thickness of lath 1.25 mm ,push pull or manual type of any size. Note: Rate is deemed to be inclusive of all the labour,tools and parts requried for easing / smooth operatiion of rolleing shutter.

Taking down steel window/ ventilator of any description and of any type with or without guard bars.

Hacking out old broken glass (any thickness, size, quality or description) from metal frames including punching or drilling out old glazing pins/spring clips and providing and fixing new ones complete all as specified and as directed by Engineer-in-Charge.

S&F sheet glass, ordinary quality 4mm thick fixed with oil putty size of glass n.exc 0.50 sqm in each pane complete all as spd & directed.

Securing glass of any description in existing metal frames glazed with putty/ beads including removing loose or decayed putty/ beads, painting/oiling one coat on rebates, grooves, reputtying and painting/oiling puttied surface to match existing work (New length of frame reputtied shall be measured)

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for doors, windows, ventilators and partitions (Fixed portions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ eoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-Charge.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as per architectural drawings and the directions of Engineer-in-Charge.

Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineerin- charge.

M&L 5.5mm thcik sheet glass ordinary quality fixed to aluminim doors with beading and glazing clips complete all as specified and directed by Engineer-in-Charge.

M&L Wire netting of stainless steel wire 1.23 mm dia fixed with tinned tacks of stainless steel wire staples Size of mesh in 12 mm

S&F Aluminium alloy, anodised, sliding door bolt 300 mm long with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

S&F Aluminium anodised, barrel tower bolts of extruded section 150 mm long and fixed

S&F 150 mm size Extruded aluminium alloy handles, fabricated type, anodised all as spd & directed.

S&F Butt hinges 100mm size, extruded aluminium alloy with galvanised mild steel hinge pin, anodised, type B-21

S&F Floor door stopper of aluminium alloy body and tongue, anodized, with hard drawn steel spring, fixed in floor, overall length of cover plate 140mm complete all as specified.

M & L for 50mm thick PCC 1:3:6 type B-1, using 20mm graded stone aggregate as in plinth protection, laid in slope in 1:30 in pannels n. exc. 2m long, concrete surfaces finished even and smooth without using extra cement

Dismantling asbestos cement (corrugated / semi corrugated) sheets including ridges as in roof covering all as specified & directed by Engineer-in-Charge.

Dismantling structural steel work including doors, gates but excluding framed truss etc.as in girder, purlin, trusses, wind ties or framed work of false ceiling in any position and in any description complete all as specified and directed by the Engineer-in-Charge.

Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to e.290.Gde-E-165

S7F Expanded metal,n exc 4 kg cut to length, bent to shape required and tying with and including annealed mild steel wire not less than 0.9mm dia or fixing with galvanised steel staples supplied and fixed complete to wood or steel members

Applying evenly a primming coat of industrial bitumen 85/25 at the rate of 0.4 kg per sq. m including cleaning surfaces

S&F APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application complete all as specified

M&L for 100mm thick cement concrete type D2, (1:4:8) using 40mm stone aggregate as in sub base.

M&L for Spreading and levelling in layers n exc. 25 cm thick including watering and consolidation.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness, M-40 Grade with grey cement and no pigment

M&L for pre-cast cement concrete type B1 (1:2:4) using 20mm graded stone aggregate) as in road side kerbs size and shape as specified and directed by Engineer-In-Charge complete.

Chequered cement concrete tiles 20cm x 20cm x 25mm thick with grey cement and pigment , set, jointed and pointed in neat cement slurry in floors including 15 mm thick screed bed or bedding layer in CM 1:6 for laying tile flooring.

Excavation in trenches n.exc 1.5 Mtr wide and n.exc 1.5 Mtr in depth in hard/dense soil and getting out complete all as directed.

Returning, filling in trenches including spreading, leveling, watering and well ramming in layers n.exc 25cm complete all as directed.

Removal of excavated material to a distance n.exc 50 mtr and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and as directed.

M&L sand cushioning / filling for underground cable protection, filling under floors ,consolidated and compacted with clean dry sand complete all as specified and as directed.

M & L stone Slab 40 to 50 mm thick rough dressed jodhpur stone patties/ slab cover in trenches for protection of cable 25 to 30 CM wide and thickness not less than 50 mm in length lay dry abutting each other with gap between adjacent slab not exceeding 10 mm over sand cushioning.

Supplying and fixing in replacement of under ground cable XLPE insulated, 1100 volt grade heavy duty armoured with standed aluminium conductor 4 core 16 sqmm laid in trenches/ duct/ pipe including all electrical connection with required lugs and nuts, bolts complete all as specified and directed by Engr-in-Charge.

Material and labour in repair for over hauling/lubrication emtrok actuator valves Model No M1/030/A and M0/030/E including replacement of unserviceable spare parts at CPH area make : Marsh, three phase, TEFC type motor DOI srarting complete entire satisfaction of Engr-in-charge. Note : defective spare parts for the above will be measurea and paid separately under Sl items

supply only actuator stroke(Stainless steel spindle 2.4 mtr long) Make as per sample

Supply only coupling piece Make as per sample

Supply only Spur gear box Make as per sample

Supply only torque switch Make as per sample

Supply only travel switchs Make as per sample

Supply only torque switch operating cam Make as per sample

Supply only locking plate Make as per sample

Supply only electronic pins Make as per sample

Supply only allen bolts M8 x 100L Make as per sample

Supply & fixing as in repair cast iron sluice valve Long body of 80 mm bore, Class PN 1.6 ISI marked with IS 14846 – 2000 with flanged ends and drilled, stainless steel spindle, CI gate with brass ring and iron wheel hand , cast iron cap, complete with neoprene rubber gasket joint and nuts, bolts (high tensile), washers etc, complete including testing all as specified.

All as per item No. 88.00 here-in-before but size of 100mm

All as per item No. 88.00 here-in-before but size of 150mm

All as per item No. 88.00 here-in-before but size of 200mm

Material and labour in repair for over hauling/lubrication of Gear box of Clariflacculator motor and including of repair of motor and replacement of winding of motor of of clariflacculator

Material and labour in repair for over hauling/lubrication of Gear box of alum mixing motor and including of repair of motor and replacement of winding of motor of Alum Mixing Chamber

Material and labour in repair for Slip ring assembly for clarifloculator

S&F in replacement DOL starter range 13 - 22 Amp including making electrical connection complete all as specified & as directed by Engineer-in-charge Make :- L&T Cat Part NoSS96228 or equivalent Crompton Greaves / ABB / Schneider / Seimens

S&F in replacement on / off switch (push button) complete all as specified & as directed by Engineer-in-charge

S&F in replacement indicating lamp with holder and cover as per existing complete all as specified & as directed by Engineer-in-charge

Supplying, laying & jointing in replacement submersible cable flat type, copper conductor of size 16 Sqmm 3 core complete all as specified & as directed by Engineer –in-charge.

All as per serial item No.27 here-in-above but 10 Sqmm 3 core.

All as per serial item No.27 here-in-above but 6 Sqmm 3 core.

All as per serial item No. 27 here-in-above but 4 Sqmm 3 core.

Supplying and fixing in replacement of electromagnetic water flow meter, Inline version, Fixed flange design, Transmeter, sensors, standard transmitter, display operation, 2.40" screen, cable, sensor connection, process connection PN 10 , carbon steel, flange EN1092-1, Electrodes 1.4435/316L, bullet nose, Flow calibration : 0.5% "Promag W 10, 5W883F, DN350 14"" Model No : 5W883F-AAEAEBKP2DUD2KGAA1+CB Make : Endress+Hauser or equivalent

Supply only Water treatment Calcium hypo Chloride 65%-70% chlorine content (calcium based granular disinfectant for water treatment, packed in 45 kg drum complete.

Supply only Water treatment Non Ferric Alum (crystal type) for water treatment, packed in 50 kg package complete.

S&F and testing in replacement of energy efficient LED street light fitting of 60 watt pole mounting comprising a diecast aluminium houing with heat resistant toughened glass with frame IP 66 protection complete all as specified and as directed.

Supply and fixing LED flood light 120 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP 66 protection, with impact and corrosion resistant complete with driver and lamp

S&F and testing of energy efficient LED Flood light fitting of 200 watt pole mounting comprising a diecast aluminium houing with heat resistant toughened glass with frame IP 66 protection of complete all as specified and directed .

S & F in repair GI Bracket for mounting street light fittings made out of light grade 32mm GI pipe and have angle of 120 degree incl fixing arrangement complete all as specified and as directed by engr-in-charge.

Supply and fix PVC insulated and PVC round sheathered cable with multi stranded copper conductor 2.5 sq mm cross sectional area 8 core ,1100 volts grade all as specified and as directed.

Supply and fix PVC insulated and PVC round sheathered cable with multi stranded copper conductor 6 sq mm cross sectional area 3 core ,1100 volts grade all as specified and as directed.

Supply and fix PVC insulated and PVC round sheathered cable with multi stranded copper conductor 6 sq mm cross sectional area 4 core ,1100 volts grade all as specified and as directed.

Supply and fix PVC insulated FR cable with multi stranded copper conductor 1.5 sq mm cross sectional area 3 core ,1100 volts grade all as specified and as directed.

Supplying and Fixing/connecting for service connection/ Garden light connection, 1100 volts grade heavy duty Cable PVC insulated aluminium multy sranded conductor, twin core cable circular of sizes 16 Sqmm 2 Core complete all as Specified and directed.

All as per Srl Item No. 113.00 here-in-before, but sizes 10 Sqmm 2 Core.

Supply and fixing in repair of post top lantern LED type 20 watt 230 watt volts AC outdoor type with decorative post top for 360 degree indirect light IP 65 protection with impact and corrosion resistant complete with driver and lamp complete.

M&L in replacement of Inverted Tripod type LED bollard light 10 watt with soft light disturbution complete all as directed by Engr-in -Charge Make :Crompton cat pat no -LBLSN-10-CDL or eqult Havells/Bajaj/Surya

M&L for taking out of Elect Motor 75 HP Capacity installed as motor from foundation after disconnecting electrical connections, dismantling motor and rewiding the same with super enamelled copper winding wire of existing gauge including varnishing, baking, cotton tape and greasing of bearings, bushes and other connected parts, reassembling and fixing the same in its original position including replacement of unserviceable nut-bolts, washer, lugs, terminal plate and making proper electrical connection complete all as specified and directed by Engineer-in-charge. Make of winding wire : - Devidayal / Chetak Note : - (i) Bearing if required for replacement shall be paid seprately (ii) Transportation of motor is included in the unit rate of items nothing extra shall be paid on this account

All as per serial item No. 117.00 here-in-above but motor of capacity 50 HP

Supply only Ball Bearing of suitable size for rotor of motor 75 HP installed complete all as specified and directed by Engineer-in-charge.

All as per serial item No 48 here-in-above but for motor of 50 HP.

Taking out defective centrifugal pump set , assembled with 75 HP elelctric motor, dismantling the pump set for carrying out repair / replacement of unserviceable parts such as CI impeller, Bush, ball bearing etc. reassembling, installing, commissioning and testing complete all as specified and directed by Engineer-in-charge. Note :(i) CI impeller, Bush & ball bearing required to replace shall be measured and paid for separately under respective items of BOQ as “Supply only”. (ii) The cost of transportation is included in the unit rate of this item nothing extra shall be paid on this account.

All as per serial item No 121.00 here-in-above but pump set assembled with 50 HP elelctric motor

Supply only ball bearing suitable for centrifugal Pump set assembled with 75 HP motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 123.00 here-in-above but assembled with 50 HP Motor

Supply only stainless steel Bush suitable for pump set assembled with 75 HP motor complete all as specified and directed by Engineer-in-charge.

All as per serial item No 125.00 here-in-above but assembled with 50 HP Motor

S&F as in replacement coupling assembly as per existing model & make suitable for centrifugal pump set assembled with 75 HP motor complete all as specified & as directed by Engineer –in-charge.

All as per serial item No. 127.00 here-in-above but assembled with 50 HP motor

S&F in replacement rubber coupling as per existing model & make suitable for centrifugal pump set assembled with 75 HP motor complete all as specified & as directed by Engineer –in-charge.

All as per serial item No. 129.00 here-in-above but assembled with 50HP motor

S&F in replacement bakelite sheet of connection plate with cable connector suitable for 75 / 50 HP motor complete all as specified & as directed by Engineer –in-charge.

S&F in replacement cooling fan with locking aluminum cast type screw, as per existing type, suitable for 75 / 50 HP motor complete all as specified & as directed by Engineer –in-charge.

S&F in replacement MCCB 4 Pole 630 Amps, thermal magnetic release having, breaking capacity 50 KA, 415 Volt in the existing feeder pillar box including any addition / alteration to the panel to accommodate the new MCCB & making connections with 25x3 mm copper strip as required from main bus bars, making necessary welding work, metal work for fixing base plate etc and connections complete all as specified and as directed by Engineer-in-Charge.

All as per item No. 133.00 here-in-before but MCCB 4 Pole, 400 Amps rating, breaking capacity 36 KA, 415 Volt

M&L for Construction of brick masonry valve pit, in repair, of internal size 90cm x 90cm x90cm including necessary excavation and earth work in soft/loose soil, brick work, plastering, white wash, PCC coping, MS frame made out of angle iron of size 40mmx40mmx6 mm, MS sheet cover of 3 mm thick fixed to angle iron frame by means of hinges welded to frame and painting with 2 coats of synthetic enamel paint over a coat of red oxide primer on steel surfaces and grouting the frame in PCC 1:2:4 type B-1 including handle and locking arrangement with one number 50 mm dia brass pad lock , complete all as specified and directed by Engineer - in - Charge Note :- (i) Brick wall shall be 23 cm thick built in cement mortar (1:4) (ii) Internal plaster shall be 15 mm thick in cement mortar (1:4) and external plaster upto 450mm from top shall be 20mm thick in CM (1:6) and remaining external surface shall be flush pointing in CM (1:6) as the work proceeds. (iii) PCC in foundation shall be 15 cm thick in cement concrete (1:4:8) type D2 using 40 mm graded stone aggregate extended 15 cm all around from the external face of the walls. (iv) PCC coping shall be 15 cm thick in cement concrete ( 1:2:4) type B1 using 20 mm graded stone aggregate including grouting of angle iron frame in PCC. (v) Three coats of white wash to internal surfaces of valve pit. (vi) Depth of valve pit shall be reckoned from the top of PCC in foundation.

All as per Srl item No 135.00 above but internal size 150cm x 150cm x 90cm

S & F for LED sign board of size 18 X 3 including writing of installations details as directed by engr in charge and including stand with 40mm x 6mm thick angle iron with flat strip including welding, cutting & installed at site incl two coats of mettallic paint over a coat of mettallc primer with PCC locking arrangement complete and pcc copping 1 :2 :4 all as specified & directed by the Engineer-in-Charge.

HINDUSTAN TRADING COMPANY (BID ID -3523117)

Om Trading Corporation (BID ID -3522317)

Harsh Enterprises (BID ID -3522944)

DEV INDUSTRIES (BID ID -3523927)

New Vishvakarma Udhyog (BID ID -3522945)

M/S SUA DEVI (BID ID -3523855)

M/s Vishaka Enterprises (BID ID -3524246)