SPECIAL REPAIR TO FENCING AT B CHARGE CL III CHARGE AND CERTAIN SANCTIONED WORKS AT RTS AND DEPOT HEMPUR UNDER GE EAST BAREILLY

Amount

M&L for dismantling posts or struts (wood, steel or RCC) any section including taking out embeded portion and making good disturbed ground complete all as specified and directed.

Excavation in post holes (or similar holes) each n' exc 0.5 Cum getting out returing, filling in and ramming earth or brocken rubble mixed with earth around in layers not exceeding 25 CM complete all as specified and directed.

M&L for dismantling fencing wiremesh, any type etc complete all as specified and directed.

S&F for framed brackets of angles or tee with web and flanges cut to shape ,drilled counter sunk for screw incl bending and welding angles gusset plates etc FE-290(Gde -E- 165)

S&F for MS plates as cleats base plates etc of FE-410-W(Gde -E- 250) complete all as specified and directed.

M & L for PCC (1:3:6) type C-2 (40 mm grade aggregate) as in foundation, filling and mass concrete etc complete all as specified and directed.

Supply only Chain Link MS galvanised fencing any size or type.

Fixing only GI chain link fencing of plain GI steel wire of dia 3.80mm and mesh size 50mmx50mm and tying to any type of standard rails, straining with required bolts etc. including provision of binding wire complete all as specified and directed.

M&L for Mild steel in flat, round or square bars, in available length , conforming to Fe-410-W(Gde E-250) of quality-B complete all as specified and directed.

S&F for mild steel bolts,purpose made with hexagonal or square head each screwed end to be fitted with washers and one hexagonal or square nut dia n.exc 12mm. Etc complete all as specified and directed.

M&L for mild steel deformed or twisted bars 10mm dia for stiffening of the fencing etc complete all as specified and directed.

M&L of two coat of synthetic enamel paint over one coat of red oxide on new steel surfaces of any description over 10cm in width or girth incl preparation of surfaces etc complete all as specified and directed..

Demolition of cement concrete (un reinforced) in ground floor & paving not exceeding 15 cm thick below or above ground level complete all as specified and directed.

M & L for PCC (1:4:8) type D-2 (40 mm grade aggregate) as in foundation, filling and mass concrete etc complete all as specified and directed.

Demolition of Brickwork or stone/boulder masonry, built in cement mortor including all quoins,arches,pillars, etc complete all as specified and directed.

M & L for brick work with sub class 'B' bricks in cement mortar 1:6 straight or curved on plan exc. 6.00m mean radius with old size bricks complete all as specified and directed.

M & L for Providing cement concrete 1:2:4 type D1 in bands,copings,kerbs including weathering, slightly chambered angles incl formwork as specified and directed

M&L rendering 10 mm thick on fare faces of concrete surfaces in cm 1:4 is to be finished even and fair ETC complete all as specified and directed.

M&L three coats of white washing on new plastered surfaces of concrete including preparation of new surfaces all as speciifed and directed

S&F for MS tubular structures as in truss, purline, rafters, conforming to Gde St-240 etc complete all as specified and directed.

S&F for MS plates, MS Flat iron as in cleats, base plates, purline etc of Gde Fe-410-W etc complete all as specified and directed.

S&F for Pre painted galvalume aluminium zinc coating GI based corroguted steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering/cladding to wall fixed with self tapping screws all as specified and directed

S&F for Pre painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50mm thick of an colour having tensile strength of 550mpa as in roof covering eaves board, gutter, valley and in cladding to wall fixed with self tapping screws all as specified and directed

Surface excavation n.exc. 30 cm deep and averaging 15 cm deep and getting out in soft/loose soil complete all as specified and directed.

M & L plain cement concrete 100mm thick 1:11/2:3 using 20 mm graded stone aggregate as in flooring with 20mm thick wearproof topping as specified (incorporting an approval metallic floor hardener 10% by weight of cement)) , laid on concrete floors and pavings and finished even and smooth without using extra cement (except metallic hardner),with spike rolling to surface or making expanded metal, whilst the concrete is green complete all as specified and as directed. (Note: Metallic floor hardner will be measured & paid separetaly.)

Supply only metallic floor hardner complete all as specified and as directed.

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m in depth in foundation and getting out in soft/loose soil all as specified and as directed.

M & L for brick work with fly ash bricks in cement mortar 1:4 straight or curved on plan exc. 6.00m mean radius built in complete all as specified and directed.

M&L for 40mm thick PCC 1:2:4, type B0 damp proof course with WPC @ 3% to the weight of cement to horizontal or vertical surfaces including necessary formwork etc complete all as specified and directed.

Earth filling under floor spreading and leveling in layers n.exc. 25cm thick including well ramming including watering as required all as specified and as directed.

M&L for Hard core of gauge n.exc. 63mm of branch stone, and leveled in layers n.exc. 15cm thick watered and rammed to a true surface all as specified and as directed.

M&L 75 mm thick PCC 1:3:6 type C1 finished even and smooth without using extra cement as in plinth protection, paths , steps etc all as specified and as directed.

Returning filling and spreading leveling watering and well ramming in layers n.exc 25 Cm in soft/loose soil all as specified and as directed.

Removing excavated material n.exc 50m and depositing where directed at a level n.exc 1.5m above the staring point in soft/loose soil all as specified and as directed.

M&L for 15mm thick rendering on fair face of brick wall or concrete surface in CM 1:6 finished even & smooth as in internal surfaces all as specified and as directed.

M&L 15 mm thick on brick wall or concrete surface consisting two layers, under layer of 10mm thick in CM (1:6) & top layer of 5mmn thick in cement mortar 1:4 mixed with water proofing compound finished even and smooth without using wxtra cement complete all as specified and directed. (Note : water proofing compound shall be measured and paid sepeeralely.)..

M&L for PCC 1:3:6 Type C2 as in surface channel & drain including form work all as specified and as directed.

M & L for extra for forming fair finished drain or channel 30 cm inner girth of cement concrete using extra cement including forms moulds, mitred/ stopped ends etc all as specified and as directed.

Supply only integral Water proofing compound.

M&L for RCC (1:2:4) 20mm graded aggregate in slab supported on walls, beams and columns in floors, roof , landings including form work all as specified and as directed.

M&L for RCC (1:2:4) 20mm graded aggregate in beam, lintel/plinth band including form work all as specified and as directed.

M&L Mild steel bars 10mm dia & over cut to length bent to shape required incl cranking bending spirally for lintels, columns, slabs incl mild steel wire (annealed)) not less than 0.90mm dia or securing with clips quality TMT bars etc complete all as specified and directed.

M & L for Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work not exceeding 200 mm thick (Horizontal or sloping) rough finished surfaces of concrete all as specified and directed

M & L for Formwork to edges of concrete flats, treads, breaks in floors, windows, cills, concrete railings, openings in concrete walls, floor and roofs n. exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar works exc 10 cm but n. exc 20 cm wide rough finished of concrete all as specified and directed.

M&L for non skid coloured ceramic tiles 7 to 8mm thick (square/rectangular) area of each tile exc. 0.06sqm but not exc. 0.11 sqm, in floors conforming to IS -13712, grade B-II (a) set and jointed in neat cement slurry and pointed with white or coloured cement to match the surface over and including screed bed layer 20mm thick in cement mortar 1:6 finished even and rough complete all as specified and directed.

S&F Glazed ceramic coloured tiles 300x200x7mm thick as in vertical surfaces of wall conforming to IS 13712 grade B-III set and jointed in neat cement slurry and pointed with white or coloured cement to match complete including screed bed layer 10mm thick in cement mortar 1:4 finished even and rough for receiving tiles on vertical surfaces complete all as specified.

S& F for steel ventilator with the top hung shutter incl hinges, steel peg stay complete all as apecified and dierected

M&L 4 mm thick figured glass, pin head type and glazing with oil putty in square n exc 0.5 Sqm in each pane all as specified and as directed.

M&L of two coat of synthetic enamel paint over one coat of red oxide on new steel surfaces of any description over 10cm in width or girth incl preparation of surfaces etc complete all as specified and directed..

S&F solid PVC door frame size 50mm x 47mm made out of 5mm plain colour PVC sheet, reinforced with MS square tube, S & F in opening as per specification & drawing.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail , lock rail and bottom rail on either side and as gap insert for top rail and bottom rail , panelling of plain colour PVC sheet to be fitted in the MS framewelded/ sealed to the stiles and rails with suitable PVC sheet beading , and jointed together with solvent cement in the frame at site as per specification.

S&F 100 mm long mild steel butt hinges medium weight cold rolled all as specified and as directed.

S&F150mm long aluminium handle, cast type, anodized all as specified and as directed.

S&F 125mm long aluminium anodized, barrel tower bolts of extruded section all as specified and as directed.

M&L for three coats of white washing on newly prepared internal wall surfaces etc complete all as specified and directed.

M&L two coat of cement based paint on newly plastered surfaces on walls

S & F Vitreous china wash basin, white, flat back, size 550mm x 400mm including, waste, chain and plug and porcelain stopperand brackets.

S&F viterous china squatting pan 'Orissa' pattern size 580x440 mm white with 'P' or 'S' trap front or back inlet and integral foot rests (excluding flushing cistern and flushing pipe)

S & F 10 Ltr capacity PVC Valveless syphonic action type flushing cistern low level white with inlet valve floot and handle, incl bracket including 32 mm bore PVC flush pipe and jointing with water closet of any type all as specified and directed.

S&F in 75 mm size PVC (SWR) floor trap plain with grating including jointing with solvent cement complete all as specified and directed.

S&F stop valve 15 mm bore, but fancy type, chromium plated with long shank and cup (concealed type) screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and directed.

S&Fin CP bib tap cast copper alloy with crutch or butterfly handle screwed down, screed for iron pipe or for brass ferrule and fixed. 15mm bore.

M&L for Cutting chases, pinning in. making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring, etc., and making good, cutting not exc 10 cm girth

S&Fin repairs CP pillar tap 15 mm bore dia copper alloy, with captsain heads, chromium plated screwed down with high pressure screwed with iron pipe.

S&F for PVC connection 15mm size with PTMT nuts of length 600mm etc complete all as specified and directed.

S & F 15mm bore of tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors etc complete all as specified and directed.

S & F 20 mm bore of tube medium grade galvanized with all fittings & fixed complete to walls & ceiling or laid in floors etc complete all as specified and directed.

S&F storage water tank(Rotational moulded PVC tank) cylindrical vertical typewith closed top hoisted & Fixing in position incl float valve and connecting to GI pipe etc complete (500 ltr capacity) including ball brass valvs high pressure with polythene float fixed to 15 mm bore pipe etc complete all as specified and directed.

M & L 20 mm thick rendering wall in 1:4 CM on brick & concrete surfaces using without extra cement with WPC @ 2% on bottom complete all as specified.

M & L for roof treatment with Polymeric membrance (APP based) with non woven Polyster mat as reinforcement with following:-(a) M & L for providing & laying a coat of cold applied bitumen 85/25 based primer on entire surface @ 0.300 Ltr/Sqm on dry and clean surfaces. (b) M & L for providing & laying APP based polymeric membrance of 3mm thickness of weight not less than 3.0 Kg/Sqm with non woven polyster fibre as reinforcement on primed surfaces by torch application with side over laps & joints over laps etc as per manufacture instructions (c) M & L for finishing of top surfaces by waer proofing roof painttwo coat of aluminium paint all as specified and as per manufacture instructions. (d) M & L for providing test with filling of water for continuous 48 hours all as specified and directed.

M&L PCC 1:3:6 type C2 (using 40 mm graded stone aggregate) concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for 100/110 mm bore pipes all as specified and as directed.

M&L 100 mm bore salt glazed stone ware drain pipes grade ‘A’ laid in trenches and jointed complete all as specified and directed. (Note :Excavation and earth work measured and paid separately)

M&L for pre cast reinforced cement concrete 1:2:4 type B1 (using 20 mm graded stone aggregate) as in landing,cover slab etc including necessary formwork set in cement mortar 1:4 complete all as specified and as directed.

M&L for PCC (1:2:4) type B-1 (using 20 mm graded crushed stone aggregate) as in benching of man holes, rounded or chamfered on edges including all necessary form work complete all as specified and directed.

M&L PCC (1:3:6) type C1(using 20mm graded crushed stone aggregate) as in coping including weathering, slightly rounded or chamfered angles and throating as directed and necessary form work complete all as specified and as directed.

M&L rendering 10mm thick in cement mortar (1:4) on fair faces of brick work or concrete surfaces to be finished even and smooth using extra cement mixed with integral water proofing compound @ 3% by weight of cement or as per manufacturer's instruction all as specified and as directed (Note : WPC shall be measured and paid separately).

M&L for 100mm thick plain cement concrete , 1:2:4 type B-2, using 40mm graded stone aggregate as in floor with spike rolling all as specified and as directed.

M&L 75mm thick plain cement concrete 1:4:8 type D2 (40mm graded aggregate) as in sub base of flooring etc complete all as specified and directed.

20mm thick screed bed or bedding layer of mortar in cm 1:6 for laying floor finishes.

M & L for Cement concrete chequered tiles 20cm x20cm x25mm thick with grey cement and pigment, set and jointed and pointed in neat cement slurry in floor etc complete all as specified and directed.

M&L cutting into existing manhole for connection of new drain pipe & removing existing drain pipe and cutting out branch channels and making good with packed spun yarn and cement mortar (1:1) and 150 mm bore pipe all as specified and as directed.

S & F PVC (SWR) pipe 110mm bore single socketed in any length with rubber ring joint laid in trenches or in floor (ISI Marked ) etc complete all as specified and directed.

S&F PVC ( SWR ) bends 110 mm bore.

Supply installation testing commission of Refrigerator (single phase) capacity of 270 litres, 4 star inverter Direct Cool Complete all as specified and directed.

M & L for point wiring complete as specified with 1100 volt grade 2.5 sq mm (nominal area) single core PVC Insulated FRLS unsheathed cable multi stranded copper conductor drawn through and including rigid non metallic PVC concealed conduct of suitable size but not less than 20 mm dia with all fittings, concealed in wall/roof/floor including decorative modular cover plate (inner and outer) suitable for housing modular pattern switches/sockets/regulators etc alognwith necessary metal boxes flush mounting in the wall duly earthed withs ame cable as for wiring above but green in colour as continous earthing wire for one 3 pin 15 Amps socket out let on independent board, complete all as specified and directed.

S & F Modular switch 15 Amp one way 230 V AC 1 module complete all as specified and directed .

S & F Socket 16A 3 Pin combined multi socket for all pins 230 V AC complete all as specified and directed

M&L for Point wiring complete with and including 1.5 sq. mm (nominal area) single core multi stranded FRLS copper conductor PVC insulated unsheathed cable 1100 volts grade I S I marked drawn through in and including concealed non metalic rigid PVC conduit 20 mm dia with accessories such as bend ,tees, junction boxes etc. anoised steel terminal boxes for mounting fittings like switches, sockets and fan regulators etc with 3 mm thick laminated sheet covers fixed with brass screws and /cup washer including one run of 1.5 Sqmm PVC insulated and unsheathed multi strand copper conductor as green colour earth wire and connected to common earth dolly complete all as specified and directed for one light/fan/Exhaust fan point controlled by one switch 5 Amps 1 way

S&F Switch piano flush type single pole one way 5 Amps all as specified and directed.

S&F ceiling rose PVC / polycorbonate isolated body 3 terminals 230 V complete all as specified and directed..

S & F for sheet metal MCB DB SPN, 4 ways ,240 V with 200 amps rated bus bar double door surface/ wall/roof/floor complete all as specified and as directed.

S&F MCB SPN, 240V with 40 amps door complete all as specified and directed

S&F MCB single pole, 240V with 5 to 40 amps door complete all as specified and directed

S & F fixing indoor decorative ultra slim LED lighting W with extruded polycarbonate envirnmental frendly complete all as specified and directged

Supply and fixing of LED building security light fitting Luminare of 18 Watt comprising of pre wired driver, pressure die cast aluminum housing heat resistant glass , with IP 65 protection complete with 1.5 meter GI tube and fixing clamps and 3 core copper cable complete all as specified and directed .

Earthing complete with galvanised steel earth plate electrode 60cmx60cm.x6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts,nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 of SSR Part I 2009 connected to earthing test point, 20 mm bore medium grade GI watering pipe, 15mm bore light grade GI protection pipe, PCC chamber with RCC cover, funnel with wire mesh etc including necessary test on completion all as specified and as directed. Note :- (a) Earth strip / Earth lead beyond 7.5m shall be measured and paid separately. (b) Cost of 15mm and 20mm bore GI pipe is deemed to be included in quoted rates.

M & L for dry and cushinonig for under ground electric cable complete all as specified and directed.

Supply and laying dry burnt bricks, sub class ‘B’ old size in cable trenches, as cable protection complete all as specified and directed

Supply and laying XLPE insulated armoured heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area 2 core 10 sqm on wall/ceiling/trenches, complete all as specified and directed.

M & L galvanised iron pipe light grade including all fitting of size 40 mm bore laying in trenches/floor for cable protection complete all as specified and directed

M & L pipe galvanized medium class including all fitting of size 25 mm bore laid in trenches or fixed in any indicated situation complete all as specified and directed.

M & L pipe galvanized medium class including all fitting of size 20 mm dia laid in trenches on fixed on wall/floor/roof complete all as specified and directed.

M & L for drilling and tapping cast iron /GI water main of any size (in position) for branch connections of internal dia 20/25 mm complete all as specified and directed. Note :- Tenderer may note that amount of credit will be deducted from the total amount arrived, at the time of Acceptance of contract.

RAMAN CONSTRUCTION CO.

raman enterprises