Repair to Wall, Floor and tiling in OTM and MD Accn at Ralawas under AGE(I) Nagtalao

Amount

Demolition brickwork or stone masonry, built in cement mortor including all quoins, arches, pillars, etc but excluding ashlar facing, dressed stonework and precast concrete articales.

M&L for squared rubble walling Jodhpur type brought upto courses, well bonded, bedded and solidly hearted, built in CM 1:6 complete all as specified and directed by Engr-in-Charge.

All as per item No 02 above but except stone.

Extra over stone walling for hammer dressing to face stones and dressing of face beds and joints of square rubble walling Jodhpur type ,brought upto course ,with maximum depression on face from straight edge held against the dressed surface not exc 20mm on sand stone .

M&L for PCC 1:2:4 type B-1 (using 20mm graded stone aggregate) as in coping.

Raking out joints/pointing to random rubble uncoursed or brought upto coursed stone masonry built in Cement Mortor.

M&L for keyed pointing to square rubble walling Jodhpur type, uncoursed or brought up to courses in CM 1:4 with water proofing compound .

Demolition for concrete block masonry wall built in any type of cement mortar complete all as specified and directed.

M&L for Pre-cast cement concrete solid block masonry in PCC 1:3:6 type C-1 in wall exc 10 cm in width and setting in CM 1:4 complete all as specified and directed.

M&L for Rendering 15mm thick on PCC block wall/concrete surfaces in CM 1:4 finishing even and smooth without using extra cement complete all as specified and directed.

M&L two coats of cement base paint on plastered/unplastered surface over priming with alkali resistant priming including preparation of new plaster surfaces.

Taking down cement plaster, wall , wall tiling from wall / ceiling/Chhajja/ Roof Projections/Lintel Bands including racking out joints hacking for key, scrubbing down with water from wall complete all as specified & as directed by Engineer in charge .

M&L for rendering 15mm thick cement plaster in CM 1:6 on stone mansonry surface finished even and smooth w/o using of extra cement.

Preparing new plastered or unplastered surfaces of wall and applying two coats of oil emulsion (bound) distemper,over a coat of primer with alkali-resistant primer paint.

Demolition of cement concrete (unreinforced) or any type of flooring in ground floors and pavings n exc 15 cm thickness (below or above ground level).

M&L for 75mm thick PCC (1:3:6) type C-1 using 20mm graded stone aggregate in path/ plinth protection surfaces including finishing surface even & smooth without using extra cement

M & L PCC 1:2:4 type B-0 (12.5mm graded agg) 25mm thick as in floors.

M&L for Non -Skid Ceramic coloured tiles 7 to 8 mm thick (Square/rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11Sqm , in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement over and incl 15mm thick screed bed in CM 1:6.

M & L non skid coloured ceramic tiles 7 to 8mm thick area of each tile exc 0.11 sqm but n exc 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete over and incl 15mm thick screed bed in CM 1:6 complete.

M&L Coloured glazed tiles 300x200x7mm thick and jointed and in neat cement slurry and pointed in white or coloured cement on vertical surfaces in dado/Skirting over and incl 15mm thick plastering in CM 1:4.

M&L Coloured glazed ceramic tiles 350x250mmx7mm thick and jointed and in neat cement slurry and pointed in white or coloured cement on vertical surfaces in dado/Skirting over and incl 15mm thick plastering in CM 1:4 on stone masonry surface.

M & L for Vitrified ceramic colour (light shade) tiles 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36sqm , in floors etc, set and jointed in neat cement slurry and pointed in white cement or cloured to match including 15 mm thick screed bed in CM 1:6 to receive floor tiles.

M & L for Vitrified ceramic colour (light shade) tiles 10mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36sqm , in vertical surface such as skirtings , dados etc, set and jointed in neat cement slurry and pointed in white cement or cloured to match including 10 mm thick rendering in CM 1:4 to receive vertical tiles.

M & L for Udaipur green marble work (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms, counter WHB and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite and making round beads at edges(double outside and single inside) complete all as specified & as directed by Engineer-in-Charge .

M&L for 75mm thick cement concrete type D-2, 1:4:8 (40mm graded aggregate) as in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L for Rubberised Chequered cement concrete tiles (in any shade) 20cmx20cmx25mm thick, set, jointed and pointed in neat cement slurry in floors over 15mm thick screed bed in CM 1:6. complete

M&L for provding and fixing machine made factory precast coloured rubberised concrete block interlocking paver tiles of min 60mm thick with 6mm top of antiabrasive material M-35 grade complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 type D-2 (using 40mm graded stone aggregate) as in sub base of flooring complete all as directed by Engineer-in-Charge.

M&L for sand cushioning/filling under floor including watering and consolidation .

S&F 600mmdia turbo vent in roofs of hangers/shed complete all asspecified and directed by Engineer-in-Charge.

Dismantling plain or corrugated steel sheeting any guage thickness incl Nainital pattern as in roof covering complete all as specified.

Supply and fixing Pre- painted galvatume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, ridges etc. fixed all as per manufactures's instructions and fixed with self thread making steel screws of length not less than 50mm as directed by Engr-in-Charge at site with suitable arangement as required complete all as specified & directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for

M & L Roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc con-forming to Fe 410 -W (Gde-E- 250).

M&L for painting of steel surface of any description exc over 10cm in width or grith with two coats of synthetic enamel paint over one coat of red oxide primer incl. preparation of new steel surfaces complete.

S&F Aluminium anodised sections in existing partition or door frame or door shutter or window frame or window shutter swing or sliding including alumnium clip cleat, sashbars , glazing clips, rubber packing, aluminium anodised beading etc of approved size and thickness including drilling holes in walls, ceilings, floors with screws and rawl plugs etc including taking down and refixing after necessary repairs complete all as specified & as directed by Engineer in charge .

S&F 150mm long aluminium anodised barrel tower bolts of extruded section and fixed all as specified.

S&F 100mm long aluminium anbodised barrel tower bolts of extruded section and fixed all as specified.

S&F Aluminium handle of size 150mm of approved make and pattern for aluminium doors.

S&F Mortice lock vertcal type 4 levers 100mm size of brass body of approved make with two sets of keys complete.

S&F 5.5mm thick sheet glass ordinary quality and glazing with aluminim snap beading in squars exc 0.5 Sqm in each pane all as specified and directed

S&F rubber beading for aluminuim doors/windows

S&F Double action floor spring hydralucilly regulated made up of minimum 1.25mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed all, as specified and directed.

S&F solar control film 25 micron reflective type sticked to glass panes as per manufacturers instruction and complete all as specified & as directed by Engineer in charge .

S&F in repairs 140mm floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring

Taking down aluminium doors with or without chowkat and refixing in same opening after necessary repair.(Items reqiured to be replaced will be paid seperatly) complete all as specified & as directed by Engineer in charge .

S&F in repair door closer aluminium (Diecast) body hydraulically regulated, designation No 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80kg and fixed

M&L for rendering 10mm thick in CM 1:3 finished even and smooth without using extra cement as on chhajja/roof projections/ceilings upto 10 M height all as specified.

Dismantling of Concrete of any description and in any position not otherwise specifically provided for including cutting of reinforcement.

S&F Mild steel TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips quality conforming to

M&L for Reinforced cement concrete (nominal mix) 1:2:4 type B0 using 12.5mm aggregate as in Chajja/Roof projections/bends/shelves etc.complete all as specified & as directed by Engineer-in-Charge .

Use & waste for form work to, chullah hoods, chajjas, troughs and similar items including edges etc rough finished flat surfaces on concrete all as specified & as directed by Engr-in-Charge

Demolition and breaking up 100mm dia drain pipes (Salt glazed ware, AC or Reinforced concrete) set in cement mortar

S&F 110mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls

S&F 110mm dia PVC (SWR) bends fixed to PVC pipes to walls complete all as specified

M & L for Plain cement concrete 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as over roof for making good depression/ undulation of roof slab.

M & L for Plain cement concrete 1:2:4 type B0 using 12.5mm graded crushed stone aggregate as in roof kerbs rounded or chamfered on edges as specified.

M&L for carring out water proofing treatment for roof in following stages complete all as specified & as directed by Engineer in charge .:- (1) M&L for rendering 10mm thick in 1:4 mixed with integral water proofing liquid all as per MFGs instructions over concrete surfaces finished even and smooth w/o using extra cement. (II) First coat of bitumen primer confirming to IS 3384 @0.40 Kg/Sqm over plastered surafces (III) Second coat of binding material using blown type bitumen confirming to IS -702 Grade 85/[email protected] kg per Sqm (IV) Third layer of APP modified polymeric membrane centre core of 20 micron HMHDPE , other film 20 micron each thickness 1.5 mm having weight 2.25 Kg/sqm (V) Final coat of binding material using blown type bitumen confirming to IS 702 of Grade 85/25@ 1.2 Kg/Sqm (VI) Final and top most layer of surface which will act as protective layer shall be of M&L for PCC padding 50mm thick in 1:2:4 type B1 (by using 20 mm graded stone aggregate) and making groove 10mm wide x 35mm deep at a distance of 600mm both side and filled with mastic bitumen in ration 1:1 (sand : bitumen) complete all as specified & as directed by Engineer in charge.

Demolition of reinforced cement concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level) including floor tiles.

M&L 20mm thick Granite (of any tpe) work (table rubbed and polished) in steps, jambs, pillars, windowcills,cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite.

Dismantling water tanks exc 250 n. exc 500 ltr capacity and removing to store complete all as specified.

S & F 500 ltr capacity rotational moulded polythene water storage tanks (clyndrical vertical with closed top) hoisted and fixed in position all as spd in SSR Part I.

Dismantling water tanks exc 500 n. exc 1000 ltr capacity and removing to store complete all as specified.

S & F 1000 ltr capacity rotational moulded polythene water storage tanks (clyndrical vertical with closed top) hoisted and fixed in position all as spd in SSR Part I.

S& F in repair, wash hand basin vitreous china flat back of size 550mm x 400mm of approved colour, including brackets , & incl PVC waste pipe 32mm bore CP brass waste coupling PVC connection with CP brass check nuts 45 cm long complete all as directed by Engineer- in- Charge .

S&F in repair flushing cistern PVC low level valve less syphonic action type 10 litre capacity with inlet, ball valve,float and handle including brackets complete all as directed by Engineer- in-Charge.

S & F in repair ,vitreous china squatting pan (Orissa pattern) of size 580x 440 mm white with integral foot rest,incl 'P' or 'S' trap & front or back inlet complete all as specified.

S&F in repairs bib taps chromium plated (fancy type) cast copper alloy with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule suitable for 15mm bore pipe Complete.

S&F in repairs pillar taps chromium plated, cast copper alloy, with capstan headed chromium plated, screwed down high pressure, with or without letter Hot or Cold with long screwed shanks and fly nuts for 15mm bore GI tubing complete.

S&F in repairs chromium plated angle valve suitable for 15mm bore GI tubing. Complete all as directed by Engineer-in-Charge.

All as per item No. 70 above but two way .

S&F in repairs PVC connections with PTMT nut 600mm long, 15mm bore complete.

S&F in repairs PVC connections with PTMT nut 450mm long, 15mm bore complete.

S&F in repairs Gun metal glove or flush cock with iron wheel, screwed both ends for iron pipe 15mm bore.

S&F in repairs Gun metal glove or flush cock with iron wheel, screwed both ends for iron pipe 20mm bore.

S&F in repairs brass Chromium plated shower rose with swivel joints 15 mm bore.

S&F in repairs CP jet nozzle with PVC pipe and all fitting.

S&F in repair Health faucet CP with PVC pipe and all fittings.

S&Fin repairs Plastic water closet seat, white, closed pattern with flat bottom, and cover and mild steel chromium plated of aluminium hinging device complete

Taking up or down 15mm bore galvanised steel tubing and connections. including cleaning for re fixing or removal to store. complete.

Taking up or down 20mm bore galvanised steel tubing and connections. including cleaning for re fixing or removal to store. complete.

S&F 15mm bore GI tubing medium grade ISI marked with all fitting and fixed complete to walls or concealed or fitted to ceilings or laid in floors complete.

S&F 20mm bore GI tubing medium grade ISI marked with all fitting fixed complete to walls or concealed or fitted to ceilings or laid in floors complete.

S & F in repairs for Vitreous china wash down water closet pan (pedestal pattern), white (excluding fixinf bolts , flushing cistern and flush pipe) complete

M&L in repair for 15mm dia PVC float valve with ball (plastic) including taking out existing complete all as specified and directed (Make : Prayag )

M&L in repair for 20 mm dia PVC float valve with ball (plastic) including taking out existing complete all as specified and directed (Make : Prayag )

Hacking out old broken glass (any thickness, size, quality or description) from metal frame including punching or drilling out old glazing pins/spring clips and providing and fixing new ones.

S&F 3mm thick sheet glass ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm each panel complete.

All as per item No 88 above but 3mm thick figured glass pin headed type.

Dwarka Enterprises

D DEV COMPANY

L AND J CONSTRUCTION CO.

Narender Constrution Company

M/S JAGDAMBA ENTERPRISES