PROVN OF RCC SHED IN OPEN AREA BETWEEN BAR AND DINNING HALL AT BLDG NO P 14 AT VIRBAHU PROVN OF 02 SECURITY WATCH TOWER AT SATAVAHANA AS AND AS TO GARBAGE POINT AT SATAVAHANA PROVN OF SAFETY RAILING FOR HILL TOP MESS AT SATAVAHANA AS AND AS WITH RE A

Amount

Surface excavation n. exc 30 cm deep and averaging 15 cm deep and getting out in hard/dense soil complete all as specified and directed.

Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil complete all as specified and directed.

Excavation over areas, exc 1.5 m and n.exc 3.0m in depth and getting out in hard/dense soil complete as specified and directed.

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm as in soft/loose soil complete all as specified and directed.

Removing excavated soils exc 1.5 Km but n. exc 5 Km and depositing where directed at a level n.exc 1.5 m above the starting point complete all as specified and directed.

M & L for Plain cement concrete 1:4:8, type D-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

M & L for use & waste Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundations and plinth beams and similar work, vertical or to batter complete all as specified and directed.

M & L for Reinforced Cement Concrete M-30 (Design Mix) (using 20 mm graded stone aggregate) as in foundations including rafts, footings, beams and mass concrete, etc complete all as specified and directed. (Note" Reinforcement will be measured and paid seperately)

M & L for use & waste Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etcetc complete all as specified and directed.

M & L Reinforced Cement Concrete M-30 (Design Mix) (using 20 mm graded stone aggregate) as in beams, cantilevers, lintels over 1.5m span complete all as specified and directed. (Note : Reinforcement will be measured & paid seperately)

M & L for use & waste Formwork to sides of pillars, posts, struts, piers, columns and stanchions for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for Reinforced Cement Concrete M-30 (Design Mix) (using 20 mm graded stone aggregate) as in columns, pillars, posts and struts complete all as specified and directed. (Note : Reinforcement will be measured & paid seperately)

M & L for use & waste Form work to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200 mm thick (Horizonal or sloping) for flat rough finished surfaces of concrete complete all as specified and directed.

M & L for Reinforced Cement Concrete M-30 Design Mix (Using 20 mm graded stone aggregate) as in slab supported on walls, beams and columns in floors, roofs, landings, balconies, and in shelves and the like etc complete all as specified and directed. (Note: Reinforcement will be measured and paid seperately)

S & F high strength corrosion resistant TMT steel bars 10 mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

S & F high strength corrosion resistantMild steel TMT bars 5mm dia and over upto and including 10mm dia in strirrups, spacers and binders spirally for hooping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips etc complete all as specified and directed.

M & L for Brick work with fly ash, straight or curved on plan exc 6m mean radius, built in cement mortar 1:6 using old size brick complete all as specified and directed.

M & L for rendering 15 mm thick in two coats (10mm+5mm each) on fair faces of brick work or concrete surfaces in cement mortar 1:4, mixed with integral water proofing compound with weight of cement in top layer as per manufacturer's instructions and finished the surface even and fair without using extra cement complete all as specified and directed. (Note : WPC shall be measured and paid separately against respective item).

M & L for rendering 10 mm thick on fair faces of brick work or concrete surfaces in cement mortar 1:6 and finished the surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for rendering 5 mm thick in cement mortor 1:3 on concrete surfaces as in ceilings and finishing surfaces even and smooth without using extra cement complete all as specified and directed.

M & L for hardcore of gauge n.exc 63 mm of broken stone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L for Sand filling under floors or in foundations including spreading, levelling, watering and consolidation complete all as specified and directed.

M & L for 100 mm thick, Cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in base of flooring/hard standing, etc, complete all as specified and directed.

M & L for 40 mm thick, plain cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) as in floors laid in alternate bays and finishing the surfaces even & smooth with using extra cement complete all as specified and directed.

S & F 3 mm thick, 38mm wide glass dividing strips and inserted in position to conform to design complete all as specified and directed.

M & L for non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.18 sqm but n.exc 0.36 sqm, in floors etc, including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for glazed, coloured, ceramic, tiles of size (350mm x 250 mm/450mm x 350mm/300mmx450mm) x 6 to 7 mm thick, on vertical surfaces such as skirting, dados etc, including 10 mm thick bedding in cement mortor 1:4 and set & jointed in neat cement slurry & pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for preparation new external surfaces of wall, chajja, facia etc and applying two coats of water based acrylic weather proof exterior emulsion (exterior wall finish) paint over a coat of primer as per manufacturer's instruction complete all as specified and directed.

M & L for preparing newly plastered surfaces of internal walls, etc and applying two coats of distemper oil emulsion over a coat of alkali resistant primer complete all as specified and directed.

M & L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and directed.

M & L for 10 mm thick screed bed in CM 1:4 mixed with WPC as per manufacturer's instructions over 25 mm thick PCC 1:2:4 type B-0 (12.5mm graded aggregate), as in levellig course, Supply and lay polymeric water proofing membrane of weight 3kg/sq.m incorporating a centre core of 90 micron thick HMHDPE film including coating the surface with a coat of water based bituminous primer @ 100gms/sq.m., followed by a coat of blown bitumen of grade 85/25 or 90/15 @ 1.2kg/sq.m. each at top and bottom of the membrane including sealing all joints by thermo fusion with minium 10cm overlap incl grovving & inserting in parapt wall all as per manufacturers instructions and applying two coats of aluinium paint over a coat of primer over the top surfaces complete all as specified and as directed. (Note: WPC shall be measured and paid seperately)

Supply only integral water proofing compound (ISI marked) complete all as specified and directed.

M & L for 75 mm thick, plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection etc, finishing cement concrete surface even and smooth without using extra cement including making joints with bitumastic filing in proportion of bitumen and sand 1:2 complete all as specified and directed.

M & L for post construction Antitermite treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron.complete all as specified and directed.

M & L for post construction Antitermite treatment Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

S & F Well seasoned 2nd class hard wood plain, solid, straight chowkat and frames, wrought, framed, rebated on the solid rounded or chamfered, put together with glue pinned at joints complete all as specified and as directed.

S & F 35 mm thick, 2nd class hardwood, factory made, Plain framed, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S & F Aluminium powder coated windows frame with shutters sliding pattern consisting of three tracked frame and 03 shutters (2 shutters glazed and 01 shutter gauge) with 4.8 mm thick tinted glass fixed with suitable EPDM rubber beading and one shutter with stainless steel mosquito proof wire cloth made of 0.36mm nominal dia wire and average aperture 1.4mm) and necessary handles/locking arrangements for shutter of Jindal (or equivelant) sections Window Frame ( Top & Sides) : 21137, Bottom L 20977, Window shutters : Top & Bottom : 20567, Sides : 20738 complete all as specified and as directed.

S & F 10mm thick powder coated (minimum 50 micron) anodised aluminium grill including jointing cleat and necessary fixing arrangement as required complete all as specified and directed. (Make: DECO DG 102 or equivalent approved make)

S & F 150 mm size, extruded Aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

S & F 200 mm long, Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and directed.

S & F 100 mm size, butt hinges, medium weight, cold rolled mild steel complete all as specified and directed.

M & L for Mild steel framed work such as grills, gratings, gates etc., with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bar, barred iron doors, ladders, framed balusters, walk ways, railings, framework of water tanks and similar work conforming to Fe-410-0 Gde E-250 complete all as specified and directed.

S & F Aluminium (Die cast) body door Closer hydraulically regulated, designation No 3, universal type, suitable for door shutter of 851 to 1000 mm in width and of weight between 61 to 80 Kg complete all as specified and directed.

S & F Floor door stopper of aluminium alloy body and tongue, anodised, 150 mm overall length of cover plate with hard drawn steel spring, fixed in floor complete all as specified and directed.

S & F Aluminium alloy anodised sliding door bolt with hasp & staple (bolt type) and fixing clipes of sheet, cast or extruded sections and fixing bolts of extruded sections or cast aluminium alloy, length of bolt of 300 mm complete all as specified and directed.

M & L for plain cement concrete 1:3:6, type C-1 (using 20mm graded stone aggregate) for embedding holdfast, bed block, cills, etc including necessary form work complete all as specified and directed.

S & F mild steel bands, straps, supports or stays of rain water, ventilating pipes including bolts, hooks (stay) for large gates, hook and pintel hinges, clamps, hold fasts, wall ties,flat iron fillets for securing wire mesh, wind tie, fan hook and similar work including necessary drilling bolting or riveting etc conforming to Fe – 290 Gde E – 165 complete all as specified and as directed.

M & L for Preparation of new or previously untreated wood and wood based surfaces of any description, not otherwise described, over 10 cm width or girth and applying two coats of synthetic enamel paint (1st grade quality) over a coat of pink primer complete all as specified and directed.

M & L for Preparation of new steel surfaces of any description, over 10 cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zine chrome primer complete all as specified and directed.

Excavating in post holes (or similar holes) each n. exc 0.5 Cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers n. exc 25cm, watering and removing surplus soil to a distance n. exc 50m and making good surface in soft/loose soil complete all as specified and directed.

M & L for Plain cement concrete 1:3:6, type C-2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concrete, etc complete all as specified and directed.

S & F MS steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I.S. 1161-1979 grade St-240 complete all as speicfied and directed.

M & L for Rolled mild steel fo grade Fe 410-W (Gde-E- 250) quality-A as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat section) including distance pices, cleat etc complete all as specified and directed.

S & F Rolled mild steel in Plates (plain or chequered) channels fo grade Fe 410-W (Gde-E- 250) quality-A, square cut or notched (ordinary and counter sunk) forming holes, without any attachment complete all as speicfied and directed.

S & F Mild steel screw bolts of 16 to 20mm dia of shank (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, length of bolt exc 15cm and n. exc 22.50cm long complete all as specified and directed.

M & L for Mild Steel Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe-290 Gde E-165 ® complete all as specified and directed.

S & F Pre-Painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as per manufacturer's instruction complete all as specified and directed.

S & F Pre-Painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in ridges/vally gutter, fixed with self tapping screws as per manufacturer's instruction complete all as specified and directed.

M & L for 100 mm thick, Cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in sub base of flooring/hard standing, etc, complete all as specified and directed.

M & L for Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment complete all as specified and directed.

M & L for plain cement concrete (1:2:4), type B1 (using 20mm graded stone aggregate) as in hold fast block or similar work like bands, plinth courses, lacing courses, parapets, fins fascia, louvers and raiings upto 60cm height, copings, kneelers, bed plates including necessary formwork complete all as specified and as directed.

M & L for preparing newly plastered surfaces of walls, etc and applying three coats of white wash complete all as specified and directed.

M & L for brick work with fly ash bricks, straight or curved on plan to any radius, built in cement mortar 1:4 as in half brick thick walls using old size brick complete all as specified and directed.

S & F high strength corrosion resistant TMT steel bars 6mm to 8mm dia., and over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips quality complete all as specified and directed.

S & F 150mm dia, 1.25mm thick, Plain, galvanised, mild steel sheeting, class 3, half round with rounded edges complete all as specified and directed.

M & L for Cutting opening in cement concrete walls (any description where reinforcement is cut through) for door, window and other openings (with or without reveals) or enlarging existing openings, including trimming surfaces to receive rendering, etc. removing rubbish to outside MD land complete all as specified and directed

S & F 150 mm bore, PVC (SWR), Soil waste and vent pipes in any length with or without ears, with cement joints, fixed to wall or laid in sunken floor, etc with all fixing accessories complete all as specified and directed.

S & F 150 mm bore, PVC (SWR) junction single, (Single T) equal or unequal with access door complete all as specified and directed.

S & F 150 mm bore, PVC (SWR) bends of any radius with oval access door complete all as specified and directed.

Demolition of Stone slabs and tiles of any description or thickness in floors, aprons etc. laid bedded and pointed in any mortar and removing rubbish upto a distance outside MD land complete all as directed by the Engr-in-Charge.

M & L for 25 mm thick, plain cement concrete 1:2:4, type B-0 (using 12.5 mm graded stone aggregate) as in sub-base of flooring, etc and finished the surface even and rough complete all as specified and directed.

M & L for Vitrified, designed, coloured, tiles, 10 mm thick, (square/rectangular) polished, area of each tiles not exc 0.36 sqm, in floors, etc including 20 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for Vitrified, designed, coloured, tiles, 10 mm thick, (square/rectangular) polished, area of each tiles not exc 0.36 sqm as in vertical surfaces such as skirting,dado, etc including 10 mm thick bedding in cement mortar 1:4 and necessary cutting of tiles complete all as specified and directed.

S & F 10mm thick, Seamless Calcium silicate designer false ceiling of size 1800x1200mm board made of siliceous and calcareous materials reinforced with cellulose fibre fixed to ceiling section with 25mm long self drilled and tapping screws having Phillips head with under head cutter at 200mm centre to centre including finishing the joints of face board with specially formulated jointed compound and 48mm wide fibre tap to provide seamless finish and Preparing new surfaces and applying two coats of distempered oil emulsion over a coat of alkali resisient primer over one or more coat of wall care putty including rubbing with sand paper to obtain a smooth surface and including provn of GI frame work for suspended seamless false ceiling comprising of GI ultra perimeter channels of size 0.55 mm thick having one flange of 20 mm and another flange of 30 mm and a web of 27 mm alongwith perimeter of ceiling, screw fixed to brick wall/partition with the help of nylon sleeves and screws, at 450 mm intervalss. then suspending GI ultra intermidieate channels of size 45 mm x 0.9 mm thick with two flanges of 15 mm each supported with ultra ceiling angle of width 25mmx10mmx0.55 mm thick fixed to soffit with GI cleat and steel expansion fasteners at 1220 mm intervals, Ultra ceiling section of 0.55 mm thickness having knurled web of 51.5 mm and two flanges of 26 mm each with lips of 10.5 mm are then fixed to the ultra intermidieate channel with the help of connecting clips and in direction perpendicular to the ultra intermidieate channel at 457 mm centres complete all as specified and directed.

M & L for Preparation of plastered surfaces of walls of any description over 10 cm width or girth not otherwise described and applying two coats of plastic emulsion paint over a coat of primer over one or more coats of wall care putty to a smooth surface complete all as specified and directed.

M & L for Preparation old plastered surfaces of walls of any description over 10 cm width or girth not otherwise described by complete removal of existing treatment and applying two coats of plastic emulsion paint over a coat of primer over one or more coats of wall care putty to a smooth surface complete all as specified and directed.

S & F factory made UPVC white colour three track sliding window made of extruded profiles with wall thickness of 2.3mm (+/-0.2mm). Window profile with hollow section with multi chamber, frame (88mm x 52mm), sliding sash (42mm x 67mm), sliding interlock (one vertical length in each shutter) (45.5mm x 28mm), glazing bead (24.5mm x 16mm) will be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc, making arrangement for fixing hardware, EPDM gasket, 1.2mm+/-0.2mm thick galvanised steel frame (30mm x 18mm) 2Nos sliding sash (30mm x 18mm) 2Nos sliding mesh sash (26mm x 10mm) profile to be inserted in required profile. Frame will be fixed to the wall with 8mm x100mm long fasteners. Hardware (touch lock of zinc alloyed (white powder coated) steel roller system, stainless steel wire cloth 0.36mm nominal dia of wire and avarage width of aperture 1.4mm and required accessories. () area n.exc 3.00 sqm fixed from ground to 3rd floors complete all as specified and as directed. (Note: The unit rate excludes cost of glass and includes all other connected accessories)

S & F 10mm thick powder coated (minimum 50 micron) anodised aluminium grill with aparture size of 105x99mm with suitable F or E section fixed to window/ventilator frame including jointing cleat and necessary fixing arrangement as required complete all as specified and directed. (Make: DECO DG 104 or equivalent approved make)

S & F 5 mm thick, tinted sheet glass, ordinary quality in square exceeding 0.5 Sqm and n.exc 1Sqm in each pane fixed to door/window/vent etc complete all as specified and directed.

M & L for Making good under cills (or over arches, lintels and bressummers) including all pinning as necessary in cement mortar 1:4 complete all as specified and directed.

M & L for Forming jambs, etc. to openings (to foregoing item), including cutting, toothing and properly bonding into old work, also facing, jointing and pointing to match existing work in cement mortar 1:6 complete all as specified and directed.

S & F 12mm thick fully glazed, toughened glass, double leaf reamless swing glass door fitted to aluminium anodised door frame, cutting to proper shape and size, drilling and aligning for propper fixing and fitted with and including heavy duty hydraulic action floor door spring with top pin assembly (01 No per leaf), locking arrangement, stainless steel handle (02 Nos per leaf), aluminium body heavy duty Hydraulic door closer of suitable size (01 Nos per leaf), door stopper of suitable size (01 No per leaf) and all other necessary fittings and fixtures and mounting the edges with dry set neoprine/EPDM gasket complete all as specified and directed.

M & L for granite stone slab (of any type) 18 to 20 mm thick (Table rubbed and polished), machine cut, colour Mexican Red/Ruby Red/Z black/Paerl black etc design/pattern as directed including inlays, borders, margins in two or more colours/shades as in steps, jambs, pillars, window cills, cooking platform etc bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including 20 mm thick screed bed in cement mortor 1:4 & cutting, polishing complete all as specified and directed. (Note: Single stone slab shall be used for entire length/height of steps, jambs, pillars, window cills, cooking platform etc and joints sahll match with the flooring complete)

S & F Powder coated (minimum 50 micron) Anodised aluminium frame for doors, windows, partition, ventilators etc with one or more rebates including joining cleat for fixing etc. complete all as specified and directed. (Note : (i) Thickness of aluminium section shall not be less than 1.5 mm).

M & L for 12 mm thick, Prelaminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work complete all as specified and directed.

M & L for preparation old decorated external surfaces of wall, chajja, facia etc by complete removing old paints by mechanical scrubber without disturbing the plastered surfaces and applying two coats of water based acrylic weather proof exterior emulsion (exterior wall finish) paint over a coat of primer as per manufacturer's instruction complete all as specified and directed.

M & L for rendering 15 mm thick in cement mortar 1:4 on fair faces of brick masonry or concrete surfaces and finishing the surfaces even and fair without using extra cement complete all as specified and directed.

M & L for Preparation surfaces of ceilings etc of any description over 10 cm width or girth not otherwise described and applying two coats of plastic emulsion paint over a coat of primer complete all as specified and directed.

M & L for 20-25 mm thick Machine cut kota stone slab flooring laid over and including 20 mm thick screed bed in cement mortar (1:6). and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing and moulding complete all as specified and directed by the Engineer-in-Charge.

M & L for Machine cut kota stone slab, 20 to 25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing, polishing & 10 mm thick, screed bed in cement mortar 1:3 as in vertical surfaces as skirting/dado etc complete all as specified and directed.

M & L for Providing precast cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) in window or door cills, lintels, bressumers, steps, quoin blocks (for use with masonry), string courses, copings. kneelers, apex stones, pier caps, columns, posts, boundary pillars, bed plates, pintle blocks, ancho-rage blocks, bonders (for stone walling) corbels, brackets, etc. (of any section indicated), with plain fair faces, including chamfers, weatherings, throating etc. and setting in mortar 1:6 complete with joints to match complete all as specified and directed. (Note: Reinforcement shall be measured and paid seperately)

S & F aluminium anodised door, single shutter type, side hung, fabricated with anodised aluminium extruded sections consisting of frame top and side member of size 63.5x38.10x2.0mm thick and door shutter consist of vertical styles of size 85x44.45x2.00mm, top and bottom rail of size 95.25x44.45x2.00mm and middle rail of size 100x44.45x2.0mm thick; top half of shutter shall be provided with 5mm thick tinted glass and bottom half shall be provided with 12mm thick prelaminated particle, medium density, interior grade, both side ldecorative including aluminium beading and rubber gaskets of suitable size including supply and fixing of 02 Nos aluminium handle of size 230mm, 01 No Hydraulic floor spring, 02 Nos aluminium tower bolt of size 200mm, one brass lock, 5 livers with two keys and necesary hinges complete all as specified and directed.

Demolition of brick work or stone / boulder masonry, built in cement mortar including all quoins, pillars etc stacking the serviceable bricks after removing mortar and cleaning for re-use and disposal of debris and rubbish to a distance n.exc 100m as directed by the Engr-in-Charge.

Dismantling of Asbestos Cement (Corrugated, Semi corrugated etc.) sheets in roof coverings with ridges complete all as specified and directed.

Dismantling structural steel work including doors, gates but excluding framed truss etc. complete all as specified and directed.

Demolition of un-reinforced cement concrete in ground floors and pavings n.exc 15cm thickness, (Below or above Ground level) and disposal of debris and rubbish to a distance upto outside MD land complete all as directed by the Engr-in-Charge

M & L for Cutting holes in brick walls exc one brick but n.exc two brick in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement oncrete 1:2:4 Type B-1 as required complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish upto ouside MD land complete all as specified and directed.

M & L for joint free non-skid, ceramic, coloured tiles 7 to 8 mm thick (square/rectangular) area of each tile exc 0.11 sqm but n.exc 0.18 sqm, in floors etc, including 15 mm thick screed bed in cement mortor 1:6 and set & jointed in neat cement slurry and pointed in white or coloured cement to match with the shade of tiles complete all as specified and directed.

M & L for preparing old plastered surfaces of walls by complete removal of existing treatment and applying two coats of distemper-oil-emulsion over a coat of alkali resistant priming coat over one or more coat of wall care putty complete all as specified and directed.

Point wiring with two runs of single core 1.5 Sq.mm. (Nominal area) PVC insulated unsheathed multistranded copper conductor cable FRLS (ISI marked) drawn through and including non metallic PVC conduit 20 mm bore medium grade (ISI marked) concealed / surface fitted type including Flush type metal GI boxes for fixing modular type / MS sunken box for conventional type switches, sockets, regulators etc. including provision of multistranded 1.5 Sq.mm copper conductor cable FRLS [ISI marked] as earth wire connected to common earth dolly and earth in distribution board complete all as specified and as directed, for one light/exhaust fan/fan point/call bell controlled by one way switch. (Note.: (i) The rate quoted is deemed to include making good the disturbed sufaces and to match the adjoining surface. (ii) The quoted rate is deemed to include cutting chases (if any) for concealed wiring including making good the same as per the existing one (iii) Modular white cover plate shall be measured and paid seperately)

All as per item No. 102 above but for One 3/5 pin socket outlet 6 amps on independent board complete all as specified and as directed.

All as per item No. 102 here in before but for one 15 Amps power point on the independent board with two runs of PVC insulated and unsheathed copper conductor cable of size 2.5 sqmm multistranded FR (ISI marked) and 2.5 sqmm PVC insulated unsheathed solid copper conductor cable FR (ISI marked) as earth lead complete all as specified and as directed.

All as per item No. 102 here in before but for one 15 Amps power point on the independent board with two runs of PVC insulated and unsheathed copper conductor cable of size 4 sqmm multistranded FR (ISI marked) and 4 sqmm PVC insulated unsheathed solid copper conductor cable FR (ISI marked) as earth lead complete all as specified and as directed.

S & F switch modular single pole one way 6 amp 240 volts,1 Module complete all as specified and as directed.

S & F switch modular single pole one way 16 amp 240 volts,1 Module complete all as specified and as directed.

S & F ceiling rose, 65 X 50mm two to three terminals, PVC/polycarbonate, insolated body complete all as specified and directed.

S & F Modular socket outlet 6A, 2/3 pin combined, 2 module,AC 230V, 50HZ,conforming to IS 1293 :2005 (incl all revisons and amendments). complete all as specified and as directed.

S & F Modular socket outlet 6A/16A, 2/3 pin combined, 2 module,AC 230V, 50HZ,conforming to IS 1293 :2005 (incl all revisons and amendments) complete all as specified and as directed.

S & F Modular white cover plate with frame, but 1 module complete all as specified and as directed.

S & F Modular white cover plate with frame, but 2 module complete all as specified and as directed.

S & F Modular white cover plate with frame, but 3 module complete all as specified and as directed.

S & F Modular white cover plate with frame, but 4 module complete all as specified and as directed.

S & F Modular white cover plate with frame, but 6 module complete all as specified and as directed.

S & F LED tube light fittings, 20 Watt, Surface and wall mounted LED batten, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser & integrated electronic driver with industrial grade heavy duty driver having THD<10% with all accessories, internally prewired and connecting up with twin core twisted copper conductor cable of suitable size including tube lamp complete all as specified and directed. (Make: Havell's Cat No. ENDURALINEARNEOBS20WLED865SPCWH or equivelant of make as per list of manufacturer)

S & F LED 150 Watt flood light luminaire, Energy saving, environmental friendly, long life, exclusive innovative die-cast aluminium, IP66, suitable for highlighting architectural facade and general purpose lighting with lamp and all accessories including mounting clamps, bolts, nuts and washers and copper conductor cable of suitable size to fittings of suitable length complete all as specified and as directed. (Make: Havell's Cat No. JETAIRISFLS 150WLED757PSYMLT G or equivelant of make as per list of manufacturer)

M & L for Sub main wiring with 2 runs of Single core 4 sqmm [ for Phase & Neutral ] PVC insulated multi stranded FRLS (ISI marked) copper cable drawn through and including surface / ceiling / concealed PVC conduit of suitable size with all conduit accesories and fittings along with 1 run of single core 4 sqmm PVC insulated multi stranded FRLS (ISI marked) copper cable as earth continuity conductor complete all as specified and as directed. (Note :- Two runs of 4 sqmm and one runs of 4 sqmm cable as earth wire and one run of conduit shall be measured as one length)

M & L for Sub main wiring with 2 runs of Single core 10 sqmm [ for Phase & Neutral ] PVC insulated multi stranded FRLS (ISI marked) copper cable drawn through and including surface / ceiling / concealed PVC conduit of suitable size with all conduit accesories and fittings along with 1 run of single core 10 sqmm PVC insulated multi stranded FRLS (ISI marked) copper cable as earth continuity conductor complete all as specified and as directed. (Note :- Two runs of 10 sqmm and one runs of 10 sqmm cable as earth wire and one run of conduit shall be measured as one length)

S & F Industrial type Air Circulator fan, 230 Volts, single phase, oscillating 450mm sweep, including Pull cord control for a speed and oscillation On/Off suitable for wall mounting complete with all accessories and electric connection complete all as specified and directed (Make : Orient, Model : Thunderstorm or equivelent model of make as per list manufacturer)

S & F Distribution Board, SPN 8 Way ,Double door with IP 54 protection including all fixing accessories complete all as specified and as directed. (Make : Indo Asian cat part No. 811826 [Optipro] or equivelant of make as perList of manufacturer's)

S & F MCB SPN 40 Amps, 240 Volts, B Curve complete all as specified and as directed. (Make : Indo Asian Cat part No. 811035[ Optipro] or equivelant of make as perList of manufacturer's)

S & F MCB SPN 6-32A Amps 240 Volts MCB B Curve , complete all as specified and as directed (Make : Indo Asian Cat part No. 811027 to 811034[ Optipro] or equivelant of make as perList of manufacturer's)

M & L for Earthing complete with galvanized steel earth plate electrode 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 meter deep below ground level) with top edge of plate not less than 1.5 meter below normal ground level, connected to galvanized steel earth lead wire 4 mm dia by means of bolts, nuts, check nuts and washers of galvanized iron or steel, all as shown in Electrical Plate No 3 of SSR Part - I, including necessary excavation and earth work, P.C.C (1:3:6) type C-I with 50 mm thick Pre-cast R.C.C. (1:2:4) type B-I cover slab (reinforced with 8 mm dia deformed bar @ 10 cm C/C both ways and suitable handle of 12 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel and 20 mm bore galvanized iron watering pipe (light grade), wire mesh, aluminium lugs, complete in all respect, GI earth wire protected by 15 mm bore (medium grade) galvanized iron pipe and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 metre and necessary testing on completion complete all as specified and as directed by the Engineer-in-Charge.

M & L Earthing complete with GI earth plate electrode 600 mm x 600mm x 6 mm thick burried directly in ground vertically to a depth not less than 2.25 m below ground level with the top edge of earth plate at depth not less than 1.5 m below ground level connected with galvanised earth strip of size 32x6mm by means of bolts, nuts, check nuts and washers protected by 40mm bore light grade GI pipe, funnel with 20mm bore GI medium grade pipe for watering, wire mesh, including concrete pit in PCC (1:3:6) type C-1, with 40 mm thick Pre-cast R.C.C. (1:2:4) type B-I cover slab (reinforced with 8 mm dia deformed bar @ 10 cm C/C both ways and suitable handle of 12 mm dia round bar), including providing charcoal or coke and common salt in alternate layers of 15 cm compacted thickness all around the earth electrode, with funnel, wire mesh, aluminium lugs, complete in all respect and other end connected with main switch board or Earthing test point as directed, including necessary earth work and disposal of spoil to a distance not exceeding 50 metre and necessary testing on completion complete all as specified and as directed by the Engineer-in-Charge.

S & F earth continuity conductor or main earthing lead with aluminium strip of size 25x3mm mm, fixed to wall on batten or recesses or chases or burried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc, as required complete all specification and directed.

S & F earth continuity conductor or main earthing lead with galvenised iron strip of size 25x4 mm, fixed to wall on batten or recesses or chases or burried in ground or drawn in conduit/pipe or fixed to poles or any other indicated situation for loop earthing etc, as required complete all specification and directed.

S & F Air termination, single pointed aluminium rod 12mm dia and 300mm long fixed to overhead reservoir as in lightening protection with necessary connections to earthing etc complete all as specified and directed.

S & F Test point terminal block made of gun metal or phosphorus bronze size 75x75x25mm drilled and screwed including 3 nos. 8mm dia 25mm long hex. head screw complete all as specified and directed.

S & F Concealed sheet metal enclosure with socket plug top and MCBs having single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB of capacity 20Amp 240V, B-curve complete all as specified and as directed.

M & L for Sub main wiring with 2 runs of Single core 16 sqmm [ for Phase & Neutral ] PVC insulated multi stranded FRLS (ISI marked) copper cable drawn through and including surface / ceiling / concealed PVC conduit of suitable size with all conduit accesories and fittings along with 1 run of single core 16 sqmm PVC insulated multi stranded FRLS (ISI marked) copper cable as earth continuity conductor complete all as specified and as directed. (Note :- Two runs of 16 sqmm and one runs of 16 sqmm cable as earth wire and one run of conduit shall be measured as one length)

S & F 2x2 recessed mounting panel light fittings, 36 Watt with all accessories, internally prewired and connecting up with twin core twisted copper conductor cable of suitable size including tube lamp complete all as specified and directed. (Make: Havell's Cat No. VENUSNEOHE2X2R36WLED840PIRSENSOR or equivelant of make as per list of manufacturer)

S & F Distribution Board, SPN 12 Way, Double door with IP 54 protection including necessary fixing arrangement complete all as specified and as directed. (Make : Indo Asian cat part No. 811828 (Optipro] or equivelant of make as per List of manufacturer's)

S & F MCB SPN 63 Amps 240 Volts B curve , complete all as specified and as directed (Make : Indo Asian Cat part No. 811037 or equivelant of make as perList of manufacturer's)

M/S S K ENGINEERS

K K INFRA

N Sydeswara Rao

K SATYANARAYANA ENTERPRISES

Raghavendra Constructions

D.CH.SURYA PRAKASH

S N N INFRAS

LEE INFRAS