CONSTRUCTION OF GRAM PANCHAYAT COMMUNITY CENTRE PANCHAYAT GHAR AT KATINDI DEVELOPMENT BLOCK SADAR MANDI DISTT MANDI HIMACHAL PRADESH Sub Head Civil work Water supply And Sanitary Installation etc

Amount

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means in all kind of soil over areas upto any depth & in width as well as any sqm on plan including getting out and disposal of excavated earth all complete including carriage of materials with in all leads, lifts and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge. Any loss to the public or private property during the course of excavation shall be the sole responsibility of the contractor which shall have to be duly compensated by him at his own cost in all cases.

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation, trenches, drains (Any width or square metre on plan), including dressing of sides and ramming of bottoms, lift upto any height, including getting out the excavated soil and disposal of surplus excavated soil as directed in all kinds of classification, of soils such as pick work, jumper work, blasting work saturated soils including chiseling or any other mixed variety of soils, dewatering and / or removal of slush and other incidentals within all leads and lifts complete in all respect as per direction and satisfaction of Engineer-in-Charge. Any loss to the public or private property during the course of excavation shall be the sole responsibility of the contractor which shall have to be duly compensated by him at his own cost in all cases.

Providing and laying, mechanically mixed and vibrated cement concrete 1:4:8 (one cement : four sand : eight graded crushed stone aggregate 40 mm (forty millimeter) nominal size) in foundation and plinth including curing complete excluding the cost of form work but including carriage of material with in all leads, lift, and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying, mechanically mixed and vibrated cement concrete 1:5:10 (one cement : Five sand : Ten graded crushed stone aggregate 40 mm (forty millimeter) nominal size) including curing complete excluding the cost of form work in foundation and plinth including carriage of material within all leads lifts and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Making plinth protection 50 mm thick of cement concrete 1:3:6 (one cement : three coarse sand (zone - III) : six graded stone aggregate 20 mm nominal size) over 75 mm (seventy five milimetre) thick bed of dry brick ballast 40 mm (forty mimi metre) nominal size, well rammed and consolidated and grouted with fine sand, including carriage of materials with in all leads, lifts and other incidentals complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying in position specified grade of reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) mechanically mixed, vibrated and curing complete excluding the cost of centering, shuttering, finishing and reinforcement all work up to plinth level including carriage of materials with in all leads, lifts and other incidentals or as per the direction and to the entire satisfaction of Engineer-in-Charge.

Reinforced cement concrete work in walls any thickness including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor any level excluding the cost of centering, shuttering, finishing and reinforcement in secified grade of reinforced cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) mechanically mixed, vibrated and curing complete as required including carriage of materials with in all leads, lifts and other incidentals or as per the direction and to the entire satisfaction of Engineer-in-Charge.

Reinforced cement concrete work in Beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor all levels excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) mechanically mixed, vibrated and curing complete including carriage of materials with in all leads, lifts and other incidentals or as per the direction and to the entire satisfaction of Engineer-in-Charge.

Reinforcement cement concrete work inArches, archribs, domes, vaults, shells, folded plate and roofs having slope more than 15° (fifteen degree) up to all floor level excluding the cost of centring, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size) mechanically mixed vibrated and curing complete including carriage of materials with in all leads, lift and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing form work with steel plates 3.15 mm ( three point fifteen millimetre ) thick welded with angle iron in frame 30x30x5 mm (Thirty millimetre x Thirty millimetre x five millimetre) so as to give a fair finish including centering, shuttering, strutting and propping etc. with wooden battens and ballies in any height of propping and centering below supporting floor to ceiling upto floor all level and removal of the same for in-situ reinforced concrete and plain concrete work including carriage of materials with in all leads, lifts and other incidentals or as per direction of Engineer-in-charge in:-

Foundation ,footing basis of columns etc. and mass concrete.

Flat surfaces, such as soffits of the suspended floors roofs , landing and the like floors etc. up to any thickness.

Beams cantilever girders and lintels, side and soffits of beams, beams haunchings, cantilevers, bressumers and lintels any depth in all heights from floor.

Columns, pillars, posts and struts square, rectangular or polygonal in plan as required.

Stair case with sloping or stepped soffits excluding landing as per direction of the Engineer-in Charge

Form work in edges of slab and breaks in floor and walls under 20 cm wide as required.

Providing tor steel reinforcement TMT bars of grade Fe-500 D or more ISI make high yield strength for reinforced cement concrete work including bending, binding and placing in position and cost of binding wire complete up to floor all levels including carriage of material with in all leads, lifts and other incidentals complete as per direction and to the entire satisfaction of Engineer-in-Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ( seven point five ) in foundation and plinth in cement mortar 1:6 (1 cement : 6 coarse sand) including curing complete and carriage of materials with in all leads, lifts and other incidentals complete as per direction and to the entire satisfaction of Engineer-in-Charge.

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ( seven point five )in superstructure above plinth level up to all floor level in all shapes and sizes in cement mortar 1:6 (one cement : six sand) including curing complete and carriage of material with in all leads, lifts and other incidentals, complete as per direction and to the entire satisfaction of Engineer-in-Charge.

Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 ( seven point five )in superstructure above plinth level up to all floor level in cement mortar 1:4 (one cement : four sand) including curing complete and carriage of material with in all leads, lifts and other incidentals, complete as per direction and to the entire satisfaction of Engineer-in-Charge.

Random rubble masonry with hard stone of approved quailty in foundation and plinth including levelling up with cement concrete 1:6:12 (one cement : six coarse sand : twelve graded stone aggregate 20 mm nominal size) upto plinth level with Cement mortar 1:6 (1 cement : 6 coarse sand) including curing complete and carriage of materials with in all leads, lifts and other incidentals, complete as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing Boulder Filling under floor including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 18 mm ( Eighteen millimetre ) thick granite stone, gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all level. Area of slab over 0.50 sqm. including carriage of materials with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing edge moulding to 18 mm ( Eighteen millimetre ) thick granite stone, marble or kota stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge including carriage of materials with in all leads, lifts and other incidentals.

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/ stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete including carriage of materials with in all leads, lifts and other incidentals.

Providing wood work in frames of doors, windows, clerestory, windows and other frames wrought, framed and fixed in position of second class deodar wood including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 40mm (forty millimeters )thick panelled glazed or panelled and glazed shutters for doors windows and clerestory windows, including black enameled iron butt hinges with necessary screws of second class deodar wood including carriage of material with in all leads , lifts and other incidentals .

Providing and fixing 40mm (forty millimeters )thick wire gauge shutters for doors windows and clerestory windows, using galvanized MS wire gauge of IS gauge desigination 85 G with wire of dia 0.56mm including black enameled iron butt hinges with necessary screws of second class deodar wood including carriage of material with in all leads , lifts and other incidentals .

Providing and fixing 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws etc.ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters including carriage of materials with in all leads, lifts and other incidentals.

Extra for providing lipping with 2nd class teak wood battens 25 mm (twenty-five milimetre) minimum depth on all edges of flush door shutters (over all area of door shutter to be measured) including carriage of materials with in all leads, lifts and other incidentals.

Extra for providing frosted glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick instead of ordinary float glass panes 4 mm thick in doors, windows and clerestory window shutters. (area of opening for glass panes excluding portion inside rebate shall be measured) including carriage of material with in all leads, lifts in all levels and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).as per direction and to the entire satisfaction of Engineer-in-Charge

Providing and fixing panelling or panelling and glazing in panelled or panelled and glazed shutters for doors, windows and clerestory windows (Area of opening for panel inserts excluding portion inside grooves or rebates to be measured). Panelling for panelled or panelled and glazed shutters 25 mm to 40 mm thick including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. 5.0 mm thick glass panes (weight not less than 12.5 kg per sqm)

Providing and fixing kiln seasoned and chemically treated hollock wood wooden moulded beading 50 mm x 12 mm (fifty X twelve mili metre) to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete in all respect.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete including carriage of materials with in all leads, lifts and other incidentals.

Providing 40x5 mm (forty into five millimetre) flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embedding in cement concrete block 30x10x15 cm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete

300x16 mm (three hundred X Sixteen mili metres)

250x16 mm (two hundred fifty X Sixteen mili metres)

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :including carriage of materials with in all leads, lifts and other incidentals.

200x10 mm (two hundred X Ten mili metres)

100x10 mm (one hundred X Ten mili metres)

Providing and fixing 50 cm (fifty centimetre) long bright finished brass kicking plate of size 100x3.15 mm, with necessary screws etc. complete including carriage of materials with in all leads, lifts and other incidentals.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete :ncluding carriage of materials with in all leads, lifts and other incidentals.

125 mm (one hundred twenty five mili metres)

100 mm (one hundred mili metres)

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete including carriage of material with in all leads, lifts and other incidentals.

Providing and fixing aluminium casement stays, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc.complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required including carriage of materials with in all leads, lifts and other incidentals.

In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works.

Providing and laying Ceramic/Spartic glazed floor tiles of size 300x300 mm (three hundred X three hundred mili metre) kajaria/nitco/jonson tiles of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (one Cement : four Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete as per direction and to the entire satisfaction of Engineer-in-Charge. including carriage of material with in all leads, lifts and other incidentals.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make kajaria/nitco/jonson tiles in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete including carriage of material with in all leads, lifts and other incidentals in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Kota stone slab flooring 25mm over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

Providing and laying vitrified floor tiles 600 mm x 600 mm x 10 mm (six hundred into six hundred into ten millimetre) with water absorption less than 0.08 % and conforming to IS: 15622, of approved make Kajaria/Nitco/Jonson tiles in all colours and shades, laid on 20 mm thick cement mortar 1:4 (one cement : four coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc. complete including carriage of material with in all leads, lifts and other incidentals in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying Vitrified tiles 600 mm x 600 mm x 10 mm (six hundred into six hundred into ten millimetre)with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make Kajaria/Nitco/Jonson tiles in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (one cement : three coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete including carriage of materials with in all respect in all leads, lifts other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. The sample and pattern of tiles should be got approved from Engineer - in - charge before use.

Providing and fixing 0.60 mm ( zero point sixty milimeters) thick prepainted steel sheet in roofing with hot dipped metallic zink coated sheet with top coat of regular modified polyster ( RNP ) organic coating of 20 microns over 5 microns primer coating to back coat of polyster of 5 microns over 5 microns primer coating including fixing with prepainted screws complete with all accesoriees as required as per the directon of engineer in charge including carriage of material with in all leads lifts and other incidentals

Providing and fixing M.S BP sheet 1.66 mm to 2 mm thick in eaves board / facia / soffit / ceiling including cutting fixing and welding to steel roof members and applying a coat of red lead primer complete as per the instructions of engineer in charge ( base members of steel work shall be measured and paid separtely including carriage of material with in all leads lifts and other incidentals.

Providing and fixing 110 mm dia (one hundred ten mili metre) with minimum pressure of 4.5 kg/sqm on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes including carriage of materials with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing on wall face unplasticised - PVC moulded fittings/accessories of working pressure 4 Kgf/sq cm for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion including carriage of material in all leads & lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

110 mm bend (one hundred ten mili metres)

110 mm shoe (one hundred ten mili metres)

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm (fifty X fifty X fifty mili metres) hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (one cement : four coarse sand) and making good the wall etc. complete. including carriage of material with in all leads, lifts and other incidentals.

110 mm diameter (one hundred ten mili metres)

6 mm (six millimeter) thick cement plaster to ceiling in cement mortar 1:3 (one cement : three sand) including carriage of material with in all leads, lifts and other incidentals.

15 mm (fifteen millimeter) thick cement plaster in single coat on rough / fair side of brick /concrete / stone wall for interior plastering for all floors including arises internal rounded angles chafers and / or rounded angles chamfers and / or rounded angles not exceeding 80 mm (eighty millimeters )In girth and finished even and smooth in cement mortar 1:6 (one cement : six sand ) including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and applying white cement based putty of average thickness 1 mm (one milimeter), of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Distempering two coats with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 (fifty) grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour. including carriage of material with In all leads, lifts in all floors and other incidentals completes as per direction and to the entire satisfaction of Engineer-in-Charge.

Finishing with Deluxe Multi Surface Paint system for interior and exterior using primer as per manufacturs specification Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @ 0.75 ltr/10 sqm of approved brand and manufacture including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Finishing with Deluxe Multi Surface Paint system for interior and exterior using primer as per manufacturs specification Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and laying water proofing treatment to vertical and horizontal surfaces of depressed portions of WC ,kitchen and the like consisting of 1st course of applying cement slurry @4.40kg mixed with water proofing compound confirming to IS 2645 in recommended proportions including rounding off junctions of vertical and horizontal surfaces 2nd course of 20mm cement plaster 1:3 (one cement:three sand) mixed with water proofing compound in recommended proportions including rounding off junctions of vertical and horizontal surface 3rd course of applying blown or residual bitumen applied hot at 1.7kg per sqm of area 4th course of 400 micron thick PVC sheet (overlaps at joints of PVC sheets shouldbe 100 mm wide and pasted to each other with bitumen at 1.7kg/sqm) as required complete including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) cera/hindware/parryware make with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked white solid plastic seat and lid including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) cera/hindware/parryware make with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china orissa pattern W.C. pan of size 580x440 mm with integral type foot rests as required including carriage of material with in all leads, lifts and other incidentals.

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin cera/hindware/parryware make of 430 x 260 x 350 mm (four hundred thirty X two hundred sixty X three hundred fifty milimeters) and 340 x 410 x 265 mm (three hundred forty X four hundred ten X two hundred sixty five milimeters) sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : One urinal basin with 5 lt. white P.V.C automatic flushing cistern as required including carriage of material with in all leads, lifts and other incidentals.

Providing and fixing White Vitreous China Wash basin cera/hindware/parryware make size 550 x 400 mm (five hundred fifty X four hundred mili meters) with a pair of 15 mm C.P. brass pillar taps wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require including carriage of material with in all leads, lifts and other incidentals.

Providing and fixing white vitreous china pedestal for wash basin cera/hindware/parryware make completely recessed at the back for the reception of pipes and fittings as required including carriage of material with in all leads, lifts and other incidentals .

Providing and fixing Stainless Steel ISI 304 (18/8) kitchen sink 510 mm x 1040 mm bowl depth 225 mm as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. The sample of heavy duty jet should be got approved from Engineer - in - charge before use including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 32 mm ( Thirty Two millimetre)dia semi rigid P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 100 mm ( One hundred Millimetre ) sand cast Iron grating heavy duty for gully trap. complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 600 x 450 mm ( six hundred into four hundred fifty millimetre) beveled edge mirror of heavy dutysuperior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing 600 x 120 x 5 mm ( Six hundred into one hundred twenty into five millimetre ) heavy duty of approved quality glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete. in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Providing and fixing CP brass heavy duty toilet paper holder complete in all respect as per direction and to the entire satisfaction of Engineer-in-Charge.

Fixing water meter and stop cock in G.I. pipe line including cutting and threading the pipe and making long screws etc. complete in all respect (cost of water meter and stop cock to be paid separately).

Providing and fixing 15 mm( fifteen millimetre )nominal bore C.P. brass bib cock of jaquar/jal/ess ess make of approved quality conforming to IS:8931 : The sample quality & series should be got approved from Engineer - in - charge before use.

Providing and fixing 15 mm ( fifteen millimetre ) nominal bore C.P. brass long nose bib cock of jaquar/jal/ess ess make of approved quality conforming to IS standareds and weighing not less than 810 gms. The sample quality & series should be got approved from Engineer - in - charge before use.

Providing and fixing 15 mm ( fifteen millimetre ) nominal bore C.P. brass long body bib cock of jaquar/jal/ess ess make of approved quality conforming to IS standareds and weighing not less than 690 gms. The sample quality & series should be got approved from Engineer - in - charge before use.

Providing and fixing C.P. brass stop cock (concealed) of standard design and of approved make conforming to IS:8931 15 mm ( fifteen millimetre )nominal bore of jaquar/jal/ess ess make. The sample quality & series should be got approved from Engineer - in - charge before use.

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15 mm ( fifteen millimetre ) nominal bore of jaquar/jal/ess ess make. The sample quality & series should be got approved from Engineer - in - charge before use.

Providing and fixing C.P. Brass extension nipple (size 15 mm x 50 mm) of approved make and quality as per direction of Engineer-in-charge. The sample quality & series should be got approved from Engineer - in - charge before use.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.The sample quality & series should be got approved from Engineer - in - charge before use including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Constructing brick masonry chamber for underground C.I. inspection chamber and bends with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover with frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg), R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 Fine sand : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand), finished smooth with a floating coat of neat cement on walls and bed concrete etc. complete as per standard design: With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

Inside dimensions 455 cm x 610 cm ( Four hundred fifty five centremetre into six hundred ten centimetre ) and 45 cm deep for single pipe line :

Inside dimensions 500 cm x 700 cm ( five hundred centimetre into seven hundred ) and 45 cm deep for pipe line with one or two inlets :

Inside dimensions 600 cm x 850 cm ( six hundred centemetre into eight hundred fifty centemetre )and 45 cm deep for pipe line with three or more inlets:

Extra for depth beyond 45 cm of brick masonry chamber including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.

For 455 mm x 610 mm ( four hundred fifty five into six hundred ten milimetre ) size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

For 500 mm x 700 mm (five hundred into seven hundred millimetre ) size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

For 600 mm x 850 mm (six hundred into eight hundred fifty millimetre ) size With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. Internal work -Exposed on wall.

15 mm (fifteen millimetre )nominal outer dia Pipes.

20 mm ( twenty millimetre ) nominal outer dia Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge as required including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge. concrete work, including cutting chargES and making good the wall etc

15 mm (fifteen millimetre )nominal outer dia Pipes.

20 mm ( twenty millimetre ) nominal outer dia Pipes.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge including carriage of material with in all leads, lifts and other incidentals. External work

15 mm (fifteen millimetre )nominal outer dia Pipes.

20 mm ( twenty millimetre ) nominal outer dia Pipes.

Providing and fixing 20 mm ( twenty millimetre ) PPR unions.

Providing and fixing M.S. holder bat clamp of approved design to sand cast iron/ cast iron (spun) pipes comprising of M.S. flat brackets made of 50x5 mm flat of specified shape, projecting 75 mm outside the wall surface and fixed on wall with 4nos, 6mm dia expansion hold fasteners, including drilling necessary holes in brick wall/ CC/ RCC surface and the cost of bolts etc. The pipes shall be fixed to the already fixed brackets with the help of 30 mm x 1.6 mm galvanised M.S. flats of specified shape and of total length 420 mm and shall be fixed with M.S. nuts, bolts, & washers of size 25x6 mm, one bolts on each side of the pipe. Total bracket length 580 mm of approved shape and design (for single 100 mm dia pipe).

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. including carriage of material with in all leads, lifts and other incidentals as per direction and to the entire satisfaction of Engineer-in-Charge.external work.

15 mm (fifteen millimetre ) dia nominal bore.

20 mm ( twenty millimetre ) dia nominal bore.

Providing and fixing PVC floor trap ISI marked of self cleaning design including fixing with approved adhesive cost of cutting and making good the walls and floors complete.

110 mm x 90 mm (one hundred ten into ninty millimetre)

110 mm x 75 mm ( One hundred ten into seventy five milimetre)

Providing and fixing high pressure PVC spigot and socket waste and ventilating pipes ISI marked including fixing with approved adhesive

110 mm dia. ( one hundred ten dia)

75 mm dia. ( seventy five millimetre)

Providing and fixing PVC single equal branch with oval access door ISI marked insertion rubber washer 3mm thick boalts and nuts complete including fixing with approved adhesive complete.

110 mm dia. ( one hundred ten dia)

75 mm dia. ( seventy five millimetre)

Proving and fixing PVC door bend with oval access door insertion rubber washer 3 mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete.

110 mm dia. ( one hundred ten dia)

75 mm dia. ( seventy five millimetre)

Providing and fixing PVC collars ISI marked including fixing with approved adhesive etc. complete.

110 mm dia. ( one hundred ten dia)

75 mm dia. ( seventy five millimetre)

Providing and fixing PVC plain bend ISI marked including fixing with approved adhesive etc. complete.

110 mm dia. ( one hundred ten dia)

75 mm dia. ( seventy five millimetre)

Providing and fixing chromium plated brass soap dish with C.P. brass brackets fixd to wooden cleats with C.P. Brass screws complete including carriage of material with all leads and lifts.

Providing and fixing C.P. Brass towel rail of size 600 mm x 20 mm complete with C.P. Brass brackets fixed to wooden plugs with CP brass screws complete including carriage of material with all leads and lifts.

Providing and fixing PVC "Y" junction with oval access door, insertion rubber washer 3mm thick bolts and nuts ISI marked complete including fixing with approved adhesive etc. complete.

110 mm dia. ( one hundred ten dia)

75 mm dia. ( seventy five millimetre)

Narender Pal

Topender Singh

AKSHAY CHAUDHARY

KRISHAN LAL

NAGENDER KUMAR

Dinesh kumar

MAHESH KUMAR