Loading
Loading…
Loading…
| # | Company | Amount | Rank | Status |
|---|---|---|---|---|
| 1 | L1₹2.7 LAccepted-AOC | L1 | Accepted-AOC L1 |
Tender Value
Refer Docs
Closing Date
17 Mar 2021, 2:00 pmClosed
Sunilkumar K A
Deputy General Manager (Projects and Planning), FACT (Cochin Division), Ambalamedu Ernakulam
Fabrication, Supply and Erection of Aluminium cable tray and motorcovers for Acid area at FACT-CD, Ambalamedu.
2021_FACT_618034_1
04026/2020-2021/E23011
Limited
Miscellaneous Works
Item Rate
90 days
AMBALAMEDU
This tender is issued on limited tender basis from the registered bidders of FACT (CD) (list CDE 107B, CDE112B)
4 documents required · 4 mandatory
₹0
Exempted
7 Jul 2021
23 Feb 2021
18 Mar 2021
23 Feb 2021
17 Mar 2021
23 Feb 2021
FABRICATION, SUPPLY AND ERECTION OF ALUMINIUM CABLE TRAY AND MOTOR COVERS FOR ACID AREA AT FACT-CD, AMBALAMEDU.
Fabrication and supply of Aluminium motor covers for Motors having capacity up to 50 Hp using aluminium sheet of thickness not less than 2mm and aluminium structural items of thickness not less than 4mm. All the items needed for the work is in contractor's scope.
Fabrication and supply of Aluminium motor covers for Motors having capacity 50 Hp to 75 Hp using aluminium sheet of thickness not less than 2mm and aluminium structural items of thickness not less than 4mm. All the items needed for the work is in contractor's scope.
Fabrication and supply of Aluminium motor covers for Motors having capacity 75Hp to 100Hp using aluminium sheet of thickness not less than 2mm and aluminium structural items of thickness not less than 4mm. All the items needed for the work is in contractor's scope.
Fabrication and supply of Aluminium motor covers for vertical Motors having capacity less than 100 Hp using aluminium sheet of thickness not less than 2mm and aluminium structural items of thickness not less than 4mm. All the items needed for work is in contractor's scope.
Fabrication, supply and erection of ladder type, Aluminium cable tray using C-channel of size 150x50x8 mm and flat bar of size 80x5 mm. Width of tray is 600mm.Horizontal support of tray shall be placed at 600mm interval using flat bar. SS M10x30mm bolt, nut , washers shall be used for tray fabrication. The work includes dismantling of old cable rack and positioning/ fixing of new rack on existing place. The cable tray to be replaced is at melter area of Sulphuric Acid Plant. The cable tray shall be dismantled from the existing position without causing any damage to the cables. The work also includes dismantling of existing LT power and control cables of different sizes from old cable rack after removing the clamps and positioning the same on newly fabricated cable tray. The cables shall be laid back, positioned, dressed and tied firmly on to the new racks. The cables shall tie at all horizontal supports of cable tray using 3 mm nylon rope. Necessary material for tying/clamping of the cable shall be brought by the contractor. The dismantled cable tray shall be shifted to the scrap yard/potash godown and work site shall be thoroughly cleaned after the work. The work shall be carried out as per the instructions of the Electrical Engineer -in-charge. All the items needed for work is in contractor's scope.
stage.html
html • 0.03 MB
tech_eval.pdf
fin_eval.pdf
aoc.pdf
finance_649821.pdf
boq_comp_chart.xlsx
xlsx
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
html • 0.03 MB
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .