SPECIAL REPAIR TO BLDG NO T-63 AND CERTAIN SANCTION WORK UNDER AGE BR-II AT YOL CANTT.

Amount

PART-I:-Surface excavation not exceeding 30 cms deep and averaging 15cms deep and getting out in any type of soil, complete all as specified.

Excavation in trenches n exc 1.5 metre wide & n exc 1.5 metre in depth for foundation etc or for shafts, wells, cesspits manholes, pier holes etc n. exc 10 Sqm on plan n exc 1.5 metre in depth and getting out in any type of soil, complete all as specified.

Returning filling in including spreading, levelling, watering and well ramming in layers not exc.25cm thick each layer of soil all as specified.

Removing excavated material not exc. 50m and depositing where directed at a level not exc. 1.5m above the starting point complete all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) not exc. 1.5 Sqm each and removing from site, all as specified.

Taking down chowkats or frames including shutters (without taking off shutters from the frame) exc. 1.5 Sqm but not exc. 4 Sqm each and removing from site, all as specified.

Dismantling plain or corrugated steel sheeting any gauge, thickness including Nainital or similar pattern roof covering, all as specified.

Dismantling timber scantlings 40 sq. cm and over in section, in any position, unframed work, complete all as specified.

Dismantling wall and ceiling boards (fiber, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets in ceiling, all as specified.

Demolition of stones or brick masonry, built in cement mortar including all quoins, arches etc., but excluding ashlar facing, dressed stone work etc.complete,all as specified.

Demolition of cement concrete (unreinforced) in ground floors and paving, not exceeding 15cm thickness (below or above ground level), un-reinforced, complete all as specified.

Dismantling timber scantlingsin fillets, rails, posts, rafters, purlins, etc. under 40 sq. cm in section complete all as specified.

Taking down cement plaster on brick or stone surfaces etc. including raking out joints, hacking for key, scrubbing down with water etc., all as specified.

Taking up or down 15mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.

Taking up or down 20mm bore, steel tubing and connections, including cleaning for refixing or removal from site, all as specified.

Rolled mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. conforming to grade Fe.410-0.Gde-E-250, steel work complete, all as specified.

Rolled sections as in Steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240s, steel work complete , all as specified.

Mild Steel framed work as Plates (plain or chequered) channels, square cut or notched (ordinary and counter sunk) forming holes, with riveted, bolted or welded attachment complete, conforming to Fe 290 Gde E-165 , all as specified.

Mild steel screw bolts (purpose made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square 30 cm long, diameter of neck 16mm, complete all as speciied.

Mild steel work as in bolt hooks (stay) hook and pintle hinges, bands, straps, hold fasts, clamps, wall ties, cleats, fanhooks etc. or similar small articles conforming to grade Fe-290 grade E-165, all as specified.

Mild steel framed work such as grills, gratings, etc with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed ballusters walk ways; railings; framework of water tanks and similar work conforming to Fe.290. Gde-E-165, all as specified.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws as specified, all as specified and directed.

Aluminium anodized snap grid frame work of size 605 mm x 605 mm as in false ceiling, flat or sloping (pattern as per manufacturer's catalogue/instruction), cutting holes for electrical fittings fixed on an including aluminium tee of size 25 mm x25 mm x1.5 mm as main runner, aluminium tee of size 25mmx25mmx1.25mm as cross runner and aluminium angle of size 25mmx25mmx1.25mm at the perimeter suspended from soffit at approx 900mm centre to centre with hangers 6mm dia galvanized (length as per site requirement) adjusting level fixed to roof by means of ceiling cleats made out of galvanized iron flat 40mmx3mm size, 60mm long and expansion hold fasteners 12.5mm dia, 40mm long including necessary scaffolding all as specified and directed.

6mm thick non asbestos fiber cement building boards as in ceiling fixed or laid/ inserted to timber/GI / aluminium framework fixed with nails, including preparation of surface and applying three coats of white wash complete,all as specified.

Rolled Mild steel sections as in framing for cladding, glazing and the like fixed with angle cleats and connecting plates, etc. similar work conforming to Fe.290. Gde-E-165, all as specified and directed.

Factory made 35mm thick second class hard wood (Sal) rail and style Plain framed, panelled shutter ( two panels) without interlocking rail and with one panel of 9 mm B.W.P. commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treatedcomplete all as specified.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side plain PVC sheet and edges shall be painted to match with plain sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 176- of MES SSR 2020 Part-II

Factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of 5 mm thick plain coloured PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site, Sheet No 1/1) specified and directed.

Factory made solid PVC Door Frame of size 50mm x 47mm made out of 5mm single side prelam PVC sheet and edges shall be painted to match with prelam sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing on page No 176- of MES SSR 2020 Part-II

Factory made fully glazed PVC window/ventilator shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; completespecified and directed. Note:- Glass shall be measured and paid separately

Steel window 1.25mm thick box type (Primer coated) ERW hollow P section of size 85mm x 35mm double rebated comprises gauged, glazed skelton shutter ERW Sec 50mm x 20mm and 1mm thick with two openable leaf consiting two Nos sash bar of T-Section 20mm x 3mm complete welded to frame with one vertical mullion of ERW box type T-section of size 30mm x 25mm and 1.25mm thick including cutting holes and making good dismantled portion in PCC M-15, type B-0 (04 No's for each window, steel duly painted with one shop coat of zinc chromate primer on prepared surfaces) and finishing the surfaces to match with existing including following fitting welded to frame shutter:-(i) Hold fast, 150mm long of 12mm x 3mm made to shape -04 Nos per window.(ii) Handle of Z section 20mm x 25mm, 100mm long -1 No per leaf.(iii) MS tower bolt 150mm long - 2 No per leaf(iv) Z section 20mm x25mm, 100 long stopper - 1 No per leaf.(v) Cleat 65mm long of hollow square 15mm x 20mm x 63mm welded to hinge -1 No per leaf.(vi) Mild steel pintle hinge of size 75mm x 12mm - 2 Nos per leaf.(vii) Flat iron fillets of size 20X3 mm for fixing wire gauge.(viii) Fabrication & fixing arrangement as per drg No. CEPZ/ TD 26/13.Make : As per Appendix 'C'.Note:-(i) Above referred drawing has not been made part of tender. The same can be seen in the office of GE during working hours on any working day.

Steel ventilator with top hung shutters including hinges with steel handle, and steel peg stay, complete with glazing bars,dovetailed or weldedall as specified.

Stainless steel wire cloth. 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples or wooden beads, all as specified.

Small fittings of 2nd class hard wood (SAL) such as brackets of any type, latch and hinge blocks, shaped door and window stops and the like, including 50mm long, medium weight, cold rolled mild steel butt hinge, articles not exc. 200 cu.cm. each all as specified.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 150mm , fixed ,all as specified.

Aluminium anodised, (ISI marked), barrel tower bolts of extruded section, length of bolt 100mm , fixed ,all as specified.

Extruded aluminium alloy handles, fabricated type, anodised, of size 150mm, all as specified.

Extruded aluminium alloy handles, fabricated type, anodised, of size 100mm, all as specified.

Stainless steel Butt hinges, medium weight, cold rolled, mild steel 100mm long, all as specified.

Stainless steel Butt hinges, medium weight, cold rolled, mild steel 75mm long, all as specified.

Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 200mm with lipping frame to match , all as specified.

Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, length of bolt 250mm with lipping frame to match , all as specified.

Applying two coats of synthetic enamel paint over a coat of pink primer on new wood or wood based surfaces of any description, exc. 10cm width or girth including preparation of surfaces, all as specified.

Applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer on new steel or steel based surfaces of any description, exceeding 10cm width or girth including preparation of surfaces, all as specified.

Sheet glass 4mm thick ordinary quality and glazing with oil putty wooden beads in squares, not exc. 0.5sqm in each pane, complete all as specified.

Machine cut kota stone slab flooring 18-20 mm thick of size not less than 550 mm X 550 mm as per sample kept in GE’s office, laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, as in floor etc, laid over and including 15mm screed layer in cement mortar 1:6 (1 cement : 6 coarse sand), cutting, rubbing, grinding and polishing to achieve mirror finish complete, all as specified.

Machine cut kota stone slab 18-20 mm thick as per sample kept in GE’s office, as in vertical surfaces such as skirting/dado/riser to steps laid and jointed with grey cement slurry mixed with pigment to match the shade of slab, laid over and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) including cutting, rubbing, grinding and polishing to achieve mirror finish complete, all as specified.

Plain cement concrete M-15, nominal mix, type B-0, using 12.5mm graded mechanically crushed stone aggregate as in floors, 25mm thick, surface finished even and fair to receive top surface, all as specified.

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.18Sqm but not exc. 0.38 Sqm, in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand) complete, all as specified.

Mat finish joint less (non skid), Premium class I grade, coloured, ceramic tiles, 7 to 8mm thick (Square/ rectangular) area of each tile exc. 0.06Sqm but not exc. 0.11 Sqm, as in floors and the like, set and jointed in neat cement slurry and pointed in white or coloured cement to match, laid over and including 15mm thick screed bedding layer in cement mortar 1:6 (1 cement : 6 coarse sand) complete, all as

Mat finish, premium quality, coloured/ printed ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, as in skirting, dado etc . set and jointed in neat cement slurry and includingincluding 10mm thick rendering in cement mortar (1:4) including necessary cutting as per site requirement complete all as specified and directed. including necessary cutting and waste as per site requirement pointed in white or coloured cement to match complete all as specified and directed.

Glazed coloured tiles of size 350x250/450x350x7mm thick as in vertical surfaces such as jointed in neat cement slurry and pointed with coloured cement to match and including 10mm thick plastering in cement mortar 1:4 (1 cement : 4 coarse sand) complete, all as specified.

Plain cement concrete M-10, nominal mix, type C-1, using 20mm graded mechanically crushed stone aggregate, 50mm thick as in plinth protection etc., surface finished even and smooth without using extra cement and laid to a slope of 1 in 24 in alternate panels n.exc. 1.20 Sqm each, 12mm wide and 5 cms deep joints shall be formed between the bays and shall be filled with mastic filling comprising a mixture of one part of heated blown bitumen VG-10 and two parts of heated coarse sand (by volume), all as specified. Note:- The unit rate include for use of form work (straight or curved).

Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. For roughly finished flat surfaces of concrete, all as specified.

Formwork to soffits of suspended slabs such as roof slabs, floorslabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping), etc. For roughly finished flat surfaces of concrete, all as specified.

Formwork to edges of concrete flats, treads, breaks in floors, window cills, concrete railings, openings in concrete walls, floor and roofs n exc 20 cm wide and sides of RCC/ PCC bands in walls, horizontal or sloping and similar work exc 10cm but not exc 20cm wide for roughly finished flat surfaces of concrete, all as specified.

Reinforced cement concrete (design mix) M-25 ( using 20mm graded crushed stone aggregate) as in beams, cantilevers, lintel, over 1.50m span all as specified.

Reinforced cement concrete (design mix) M-25 ( using 20mm graded crushed stone aggregate) as in Slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like, complete all as specified.

PCC M-15, nominal mix, B-1 using 20mm graded mechanically crushed stone aggregate as,roof/chajjas kerb or mud stops ,rounded or chamfered, complete all as specified.

PCC M-15, nominal mix, B-1 using 20mm graded mechanically crushed stone aggregate as, in lintels up to 1.5 metre clear span cuts, steps seismic and other similar bends, coping, bed block ,bands plates for serving hold fasts etc. and the like including weathering slighting rounded or chamfered angles and throating complete all as specified. Note:- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.

TMT bars 10mm dia and over, cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips , all as specified.

TMT bars 5mm to 10mm dia , cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips , all as specified.

TMT bars 6 to 8mm dia cut to length, bent to shape required including cranking, bending, spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips as in stirrups, spacers and binders, all as specified.

75mm thick Plain cement concrete M-7.5, nominal mix, D-2, using 40mm graded mechanically crushed stone aggregate as in sub base complete all as specified.

Fly ash brick work with old size bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan exceeding 6 metre mean radius built in cement mortar 1:6 (1 cement : 6 coarse sand), complete all as specified.

Brick work with old size fly ash bricks having crushing strength not less than 75 Kg/Sqcm, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 (1 cement : 4 coarse sand), all as specified.

Rendering cement plaster 15mm thick in cement mortar 1:4 (1 cement : 4 coarse sand) on fair faces of brick wall or concrete surfaces, surface finished even and smooth without using extra cement with WPC , all as specified. Note :- water proofing compound shall be measured and paid separately

Rendering plaster 15mm thick in cement mortar 1:6 (1 cement :6 coarse sand) on other than fair faces of brick wall or stone wall surfaces, surface finished even and smooth without using extra cement, all as specified.

Rendering cement plaster 5mm thick in cement mortar 1:3 (1 cement : 3 coarse sand) on ceiling, surface finished even and smooth without using extra cement, all as specified.

Preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over 2mm thick wall care putty in two layers ( each Layers will be of 1mm thick) complete, all as specified.

Preparation of old plastered wall surfaces and applying two coats of oil bound distemper over 2mm thick wall care putty in two layers ( each Layers will be of 1mm thick) complete, all as specified.

Preparation of newly plastered wall surfaces and applying two coat of exterior emulsion (acrylic emulsion paint), over coat of exterior primer, complete all as specified and directed.

Complete removal of exiting treatment and applying two coat of exterior emulsion (acrylic emulsion paint), over coat of exterior primer, complete all as specified and directed.

Supply only integral water proofing liquid admixtuers compound (ISI marked) or approved brand.

Mild steel galvanized iron water tubing 15mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor complete, all as specified and directed.

Mild steel galvanized iron water tubing 20mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. Fixed to wall or ceiling or laid in floor , complete, all as specified and directed.

Bib taps, 15mm bore, fancy type cast copper alloy with crutch or butterfly handle, chromium plated screwed for iron pipe or for brass ferrule and fixed in repair , all as specified.

Stop valve fancy type wall flanged , cast copper alloy, chromium plated screwed down ,high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed complete, all as specified.

Stop valve fancy type, cast copper alloy, chromium plated screwed down ,high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions and fixed complete, all as specified.

Harrison 20mm bore Curtain rails, mild steel, chromium plated with fixing brackets, stops and roller etc. fixed in repair complete all as specified.

Brass Chromium Plated, tubular towel rail, 20mm dia, D type, 60cm long between flanges, with brackets, fixed with chromium plated screws, fixed in repair, complete all as specified.

Soap dish, chromium plated, fixed to plugs with chromium plated, brass screws, all as specified.

Chromium plated (Health Faucet) (ABS Body) with 1 Meter Long PVC Tube & Wall Hook, complete all as specified.

15mm bore Brass CP mixer for mixing hot & cold water screwed down for iron pipe and fixed fixed in repair complete all as specified.

Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long, complete all as specified

Rotational moulded polyethylene water storage tank 500 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position inbcluding PVC float ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line including dismantling old cemented/ asbestos water/ PVC storage tank, all as specified.

Rotational moulded polyethylene water storage tank 500 Ltrs capacity (Cylindrical vertical with closed top) hoisted and fixed in position inbcluding PVC float ball valve 20mm dia epoxy coated aluminium rod with polythene float and fly nut, tank nipples with check nuts and washers complete and making connections with existing water supply line complete, all as specified.

Stop valve, cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions including 1 No. 20mm union cutting ,threading existing GI pipe at a level of 1.8 M and fixed in repairs complete, all as specified.

Vitreous China wash down water closet (pedestal pattern) with including flushing cistern of size 800mmx375mmx650mm coloured including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC coloured seat cover and chromium plated jet including 15mm dia PVC connection 450mm with CP brass coupling nuts and PVC washers at both ends , fixed complete , fixed in repair complete all as specified.

Vitreous China wash down water closet (pedestal pattern), coloured including traps, connection to drain or outgoing pipe, flushing pipe, anti-syphonage pipe complete including fittings, PVC coloured seat cover and chromium plated jet including 15mm dia PVC connection 450mm with CP brass coupling nuts and PVC washers at both ends , fixed complete ,including PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve , float and handle with brackets with including 32mm dia PVC long bend flush pipe 90cm long pipe , fixed complete all as specified.

Vitreous China Urinal, Half stall type,white ( white (minimum) with grating and union for discharge pipe, complete including providing and fixing plugs, beding urinal against wall in cement mortar 1:2 securing urinal plugs with and including 60mm long brass screws, pointing around urinal back in cement, including 32mm bore PVC waste pipe, complete all as specified.

Wash basins, Vitreous China counter table top ( oval shape) size420mmx420mmX135mm, coloured fixed in granitecounter by making suitable hole with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with CP coupling nuts at both ends, waste pipe of polythylene of low or high density or PVC of 32mm dia including Pillar taps fancy type, 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed , complete all as specified.

Wash basins, Vitreous China (Flat back type) size 550mmx400mm, crystal white with and including cutting for and pinning on ends of brackets, 450 mm long PVC connections 15mm size with CP coupling nuts at both ends, waste pipe of polythylene of low or high density or PVC of 32mm dia including Pillar taps fancy type, 15mm bore cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, 32mm dia waste fittings, brass chromium plated with long screwed shanks and fly nuts, flange and bedded in red lead cement and other end fixed, screwed for iron pipe and fixed , complete all as specified.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall of bore 75mm including fixing adjustable clamps complete, including taking up or down old pipe , all as specified.

PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed to wall of bore 110mm including fixing adjustable clamps complete, including taking up or down old pipe , all as specified.

PVC (SWR) bends any radius, 110mm bore( fitted with oval access door, all as specified.

PVC (SWR) bends any radius, 75mm bore jointed with solvent cement( fitted with oval access door all as specified.

PVC (SWR) junction single, (Single T) equal or unequal, 110mm bore, provided with oval access door all as specified.

PVC (SWR) floor trap, plain with grating including jointing with solvent cement, dia of outlet 75mm, all as specified.

Aluminium (diecast) body door closer hydraulically regulated, designation No. 2, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg and fixed in repair,complete all as specified.

Plain cement concrete M-10 nominal mix, type C-1 using 20 mm graded mechanically crushed stone aggregate as in surface channel and drains (including necessary form work) including forming fair finished drain or channel 30cm inner girth in cement concrete using extra cement including forms, moulds etc. all as specified. complete, all as specified.

Taking down aluminium door shutter n. exc 2 Sqm each, taking out servicable glass panes, hydraulic door clocer, but hinges, double action hydraulically regulated floor spring and other fittings, if required carefull and refixing in the same opening after repairs of unserviceable or loosened joints/cleats of top rail/bottom rails/lock rails and styles etc and fixing old serviceable glass, any thickness with rubber packing and aluminium beadings, fixing of old servicable hydraulic door closer, double action door spring duly oiling/greasing and fixing all servicable fitting complete all as directed by Engr-in-Charge. NOTE;- Unservicable door closer, double action floor spring, glass panes and other fittings etc shall be replaced and paid under separate items of schedule.

Supply fabricate & fix in position aluminum powder coated (Minimum thickness of powder coating 50 micron of approved colour) three track window (two shutters glazed & one shutters wire gauge) with frame, glazed with 4mm thick tinted glass and, wire gauge with stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm ,including rubber bead joining cleat for fixing in position, concealed type lock for all three shutter, PVC roller etc all as specified below, complete all as specified and directed. (a) Frame (top & side) section shall of size 92.00 x 31.75 x 1.50mm (section No 20831) (b) Frame (bottom) section shall of size 92.00 x 31.75 x 1.50mm (section No 20832) (c) Top & side Members of shutter section shall be of size 18.00 x 40.00 x 1.55mm (Section No 20738) (d) Shutter Interlock sectioni shall be of size 18.00 x 40.00x1.45mm (section No 20737) (e) Bottom Members of shutter section shall be of size 18.00 x 40.00 x 1.55mm (Section No 20736) Note:-Section No given above are of make jindal, contractor may use similar section of other make mention in Appx 'C'.

Supply fabricate & fix in position anodised aluminium powder coated (minimum thickness of powder coating 50 micron of approved colour) door shutter with frame, partly glazed with 5mm thick tinted glass and partly panelled with 9mm thick prelaminated particle board with both side decorative laminated including rubber bead joining cleat for fixing in position, aluminium door handle 150mm size, aluminium barrel tower bolt 200mm size etc all as specified below complete all as specified and directed. (a) Frame ( top & side) section shall of size 101.60 x 44.75 x 2.4mm (Section No 14021) (b) Vertical Members of shutter section shall be of size 85.00x44.45x2.00mm (section No 19560) (c) Top Members of shutter Section shall be of size 83.50 x 44.45 x 2.00mm (section No 19581) (d) Lock rail (Middle member) of shutter section shall be of size 150.00x44.45x3.00mm (section No 19596) (e) Bottom Members of shutter section shall be of size 150.00x44.45x3.10mm (section No 19584) (f) Glazing clip for securing glass of shutters shall be of 0.80mm thick (section No 19370) Note:- (i) Section No given above are of make jindal, contractor may use similar section of other make mention in Appx 'C' (ii) Floor door spring will be measured & paid separatlly .

Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per specifications and drawing all as specified.

5mm thick PVC sheet fillet with 35mm for wall paneling inclusive of fixing on to wall to make PVC frame complete, all as specified and directed.

Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment laid over and including 50mm thick sand cushion, joints of tiles filled with dry sand and compacted with mechanical vibrator complete all as specified and directed.

Brass,Chromium plated 15mm bore Single Lever Basin Mixer with Popup Waste System,600mm Long Braided Hoses & Base Flanger, screwed for iron pipe complete, all as specified.

Marble 20mm thick , green marble , (table rubbed and polished) as in floor ,kitchen cooking platform /shelf and verticle surfaces duly machine cut in skirting /dado and like laid over and including 15mm thick screed bed in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with marble shade green marble type, all as specifiedand directed.

Rounding to edges of stone slabs of any type one edge , such as in steps cooking platform , cill of window and other simillar situations complete all as specified.

Stop valves, cast copper alloy, fancy type chromium plated with long shank and cup (concealed type) screwed down ,high pressure with crutch or butterfly handle, screwed both ends for 15mm bore iron pipe or for unions and fixed complete, all as specified.

Plain cement concrete M-7.5, nominal mix, D-2, using 40mm graded mechanically crushed stone aggregate as in foundation, filling and mass concrete, as in sub base layer under floors, sunken floor, all as specified.

Hard core of broken stone or boulders of gauge not exc. 63mm deposited, spread and levelled in layers not exc. 15cm thick, watered and rammed to a true surface, all as specified.

Two coats of cement base paint on newly plastered surface of wall including preparation of surface complete all as specified and directed.

Two coats of dry distemper on newly plastered surface of wall including preparation of surface complete all as specified and directed.

Three coats of white wash on newly plastered or previously undecorated surfaces of ceiling including preparation of surfaces complete, all as specified.

Figured glass, pin head type 3mm thick and glazing with oil putty/ wooden beads in squares, not exc. 0.5sqm in each pane, complete all as specified.

Gun metal, globe or gate valves , screwed down, high pressure with crutch or butterfly handle, screwed both ends for 20mm bore iron pipe or for unions and fixed complete, all as specified.

Gun metal, globe or gate valves , screwed down, high pressure with crutch or butterfly handle, screwed both ends for 25mm bore iron pipe or for unions and fixed in repair complete, all as specified.

PVC connection 15mm size with PTMT nuts at boths end 450mm long and fixed icomplete , all as specified.

20mm bore Ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and fixed , all as specified.

Vitreous Chinaware squatting pan, ‘Orrisa pattern’ size 580 mm x 440 mm, crystal white, with cast iron ‘P’ or ‘S’ trap, front or back inlet, integral foot rest with provision of plain cement concrete M-15, type B-I using 20 mm graded crushed stone aggregate and including PVC valveless, syphonic action type flushing cistern 10 litres capacity low level with inlet, ball valve , float and handle with brackets,32mm dia flushing pipe, anti-syphonage pipe with fittings,complete all as specified, connections to trap and to flush pipe, etc complete, all as specified.

Cast iron soil, waste and vent sand cast pipes of 100mm bore in any length with or without ears, with cement joints, fixed to walls with MS clamps etc , complete all as specified .

Cast iron soil, waste and vent Sand cast pipes of 100 mm bore in any length with or without ears, with cement joints, laid in trenches or in floors or without ears, with cement joints, complete , all as specified .

Cast iron soil, waste and vent sand cast pipes of 75mm bore in any length with or without ears, with cement joints, fixed to walls with MS clamps etc , complete all as specified .

75mm bore Cast iron floor trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified .

Cast Iron vent cowl 100mm, complete all as specified.

Salt-glazed stoneware gully traps, round mouthed, type 'P ', of size 150mmx 150mm, including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified .

Cast Iron 100mm sanitary connections sahort connection pipe of length upto 300mm , complete all as specified.

Precast reinforced cement concrete M-15, type B-1 (using 20mm graded mechanically crushed stone aggregate) but in landings, cover slabs (for man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces, set in cement mortar (1:4) (1 cement : 4 coarse sand), all as specified. Note :- (i) The unit rate include for use of form work (straight or curved). (ii) Reinforcement if any shall be measured and paid separately.

Concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested, in plain cement concrete M-7.5, nominal mix, type D-2 using 40mm graded stone aggregate, for bore of pipe 150mm. (For width and depth of PCC bed - refer preamble (a) (i) (ii) on page 391 of SSR Pt-II).

Salt glazed stone ware gade 'A' drain pipes, laid in trenches and jointed complete,internal dia of pipe 150mm, all as specified.

Mild steel galvanized iron water tubing 25mm bore with screwed & socket joints, medium grade, in short lengths, with and including all fittings, such as sockets, bends, elbows, unions, tees, diminishing pieces etc. laid in trenches including taking up old complete, all as specified and directed.

Drilling and tapping GI water mains (in position for branch connection of internal bore 25mm) including provision of clamps, nutsbolt, furrle all as specified all as specified.

Part-IITaking down point wiring with aluminium/ copper conductor for light point, fan & socket point/ power point etc. complete including light fiitings any type,switches, sockets, holders, (batten or pendent type), ceiling rose, switch board , bell/buzzer,bell push, tube light fitting ,regulator etc. and making good to the disturbed surfaces of wall/ floor etc. to match with existing surfaces including white wash/ colour wash/ distempering to match with existing wall/ floor/ ceiling finishes and all as specified and directed.

Taking down sheet metal enclosure DB, MCB, main switch etc and making good distrubed surfaces to match with existing surfaces, complete all as specified.

Point wiring with 1.5 Sqmm copper conductor FRLS (Multi strand) PVC insulated ISI Marked unsheathed cable in and including casing-n-caping medium grade, ISI marked of suitable size with all fittings/ accessories and also including PVC insulated ISI marked unsheathed 1.5 Sqmm copper multistranded conductor FLRS as phase, neutral and earth wire connected to common earth dolly and including concealed pressed steel/ cast iron of suitable sizes terminal boxes made from 1.60 mm thick sheet for mounting of switches, sockets, fan regulators, light fittings etc. covered with 3mm thick plastic laminated sheet (Make Hylum or equivalent ISI marked) for one light point or one fan point or one bell point, independent, controlled by one way switch/ push button complete all as specified and directed. Note:-i) Wiring colour code i.e Red/Yellow/Blue for phase , Black for neutral and Green for earth shall be maintained. ii) The wire from switch board to ceiling rose shall be of 2x1.5Sqmm +1x1.5sqmm rates for the same shall deemed to be included in item .

All as per serial item No '139' above, but for one 3 pin 5 Amps socket outlet on the same board all as specified and directed.

All as per serial item No '139' above, but for one 3 pin 5 Amps socket outlet on the independent board, all as specified and directed.

All as per Srl item No. '139' hereinbefore but for 3 pin 15 amps socket out let on independent with 2.5 Sqmm PVC copper conductor cable and PVC insulated, unsheathed 2.5 Sqmm stranded copper conductor cable as continuous earth wire, all as specified.

Switch piano flush type, single pole, one way, 5/6 Amps, all as specified.

Switch socket outlet Two -in -One 3 pin 5 amps flush type, 230 volts AC multipurpose all as specified.

Switch socket combination 5 Pin, 5 Amp & 15 Amp flush type controlled by one switch, all as specified.

Ceiling fan regulator step type, electronic type varying 5 Speeds 230 Volts, 50Hz, suitable for 1200/ 1400 mm sweep ceiling fans, all as specified.(Makes as mentioned in Appendix 'C').

Ceiling rose, three phase, PVC/Polycarbonate, insulated body, all as specified.

Switch , bell push, flush type, 5 Amps, all as specified.

Bell electric, ding dong AC 230V, single pole, all as specified.

Sheet metal enclosures factory made for DBs when MCBs to be used, single pole and neutral (double Door), 8 way, 240 volts with 200 Amp rated bus bar, all as specified.

Sheet metal enclosures factory made for DBs when MCBs to be used, single pole and neutral (double Door), 4 way, 240 volts with 200 Amp rated bus bar, all as specified.

Sheet metal enclosures factory made for DBs when MCBs to be used, triple pole and neutral, 4 way, 415 volts with 200 Amp rated bus bar, double door with detachable gland plate, all as specified.

MCB SP 6 to 40 Amp, 240 Volts, 10 KA all as specified. Note:-The connection to the MCBs shall be through thimble/lugs for and rate for the same shall deemed to be included in quoted rates

MCB SPN 6 to 32 Amp, 240 Volts, 10 KA all as specified. Note:-The connection to the MCBs shall be through thimble/lugs for and rate for the same shall deemed to be included in quoted rates

MCB TPN 63 Amp, 415 Volts, 50 Hz, 10 KA all as specified. Note:-The connection to the MCBs shall be through thimble/lugs for and rate for the same shall deemed to be included in quoted rates

Replacement of Sub main wiring with two single core PVC insulated cable 1100 volts grade with copper stranded FRLS conductor of size 4 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire of size 4 Sqmm and drawn into and including surface PVC casing & capping of suitable size with all fittings/ accessories, junction boxes 1 to 4 way 25mm dia and connected to common earth dolly, complete and as directed.Note :- Two run (each run of 1 RM) of 6 sqmm copper conductor and one RM of earth wire of 6 Sqmm, shall be measured as one RM).

Replacement of Sub main wiring with two single core PVC insulated cable 1100 volts grade with copper stranded FRLS conductor of size 6 Sqmm (2 single run) with one continuous FRLS copper earthing lead wire of size 6 Sqmm and drawn into and including surface PVC casing & capping of suitable size with all fittings/ accessories, junction boxes 1 to 4 way 25mm dia and connected to common earth dolly, complete and as directed.Note :- Two run (each run of 1 RM) of 6 sqmm copper conductor and one RM of earth wire of 6 Sqmm, shall be measured as one RM).

Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver all in one fxture, 10 watt LED and making connection with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete , all as specified.

Basic all purpose surface and wall mounted LED batten with polycarbonate housing & integrated electronic driver all in one fxture, 18 watt LED and making connection with 3 core copper flexible cable of size 23 x .0076 from ceiling rose/ PVC connector to light complete , all as specified.

Taking down ceiling fans//exhaust fan of 1200 /250/300mm sweep of any make/ Model from fan hook/ wall dismentling blade opening of motor for overhauling/servicing , and then properly cleaning alll parts and greasing , oiling of bush & bearings after opening of the fan including reassembling and Painting of ceiling fans/exhaust fan after due preparation complete at site with super enamel synthetic white paint by spray gun including filling cavities with filler, one coat after cleaning all dust etc and writing MES No with black paint and than re-hanging and reconnecting of fan with new flexible cord of suitable size from ceiling rose to connector , complete all as directed by Engineer-in-Charge.

Energyy efficient Exhaust fan PVC, 250mm sweep,1400RPM with louvers shutter and connecting up including provision of three core flexible copper wire of size 1.5 mm Sqmm from connector to ceiling fan complete in all respect all as specified and directed.

PANEL 2' X 2', 28 wattEnvironmental friendly, new generation,aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source, suitable for Armstrong/Grid ceiling. including connecting up with twin core twisted flexible copper conductor cable with suitable size, all as specified.

Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, complete all as specified.

Replacement of motor suitable for plastic body exhaust fan of size 200/250mm sweep and making necessary connection complete all as specified and as directed.

Replacement of blade suitable for plastic body exhaust fan of size 200/250mm sweep and making necessary connection complete all as specified and as directed.

Replacement of plastic body suitable for exhaust fan of size 200/250mm sweep and making necessary connection complete all as specified and as directed.

Supply and replacement of louvers suitable for plastic body exhaust fan of size 200/250mm sweep and making necessary connection complete all as specified and as directed.

XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 35 Sqmm 3.5 core laid in trenches passing through pipe/ ducts/ surface of wall ceiling etc including testing after laying complete all as specified.

XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 10 Sqmm 2 core laid in trenches passing through pipe/ ducts/ surface of wall ceiling etc including testing after laying complete all as specified.

Sand cushioning to under ground cables, 8 cm thick layer before laying and testing the cable and 15 cm thick after laying and testing of the cable in trenches complete all as specified in Clause 19.75 of MES SSR 2009 Part-I and directed by Engr-in-Charge.

Sub class 'B' bricks old size, as cable protection cover, laid dry, flat, transversally along the length of cable, on sand cushioning, with width equal to the length of the brick, complete all as specified and directed.

Mild steel galvanised light grade 40mm dia tubing with all fitting; laid in trenches, across road or on pole complete all as specified.

Mild steel galvanised light grade 50mm dia tubing with all fitting; laid in trenches, across road or on pole complete all as specified.

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 metre deep below normal ground level) with top edge of plate not less than 1.5 metre below ground level, connecting to galvanised iron wire 4.0mm dia (as earth lead wire), by means of bolt, nuts, check nuts and washer of galvanised and earth wire protected by provision of galvanised iron pipe light grade, 15 mm bore including provn of concrete pit in plain cement concrete M-20 type B-1 using 20mm graded crushed stone aggregates with 40mm thick cover of rainforced cement concrete M-20 reinforced with XPM (weight not less than 4 kg/Sqm) and frame of angle iron 25x25x3mm with lugs 2 Nos and with 6mm dia mild steel bar handle made to shape, galvanised iron medium grade 20mm bore pipe for watering perforated at bottom 1.75 metre long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorous bronze with fixing arrangement, funnel, wire mesh and including earth work in any type of soil, returning filling in and removal of surplus soil to a distance not exceeding 50 metre, all as per electrical plate No. 3 of SSR 2009 Part-I and connection to earth test point all as specified and testing on completion. NOTE :- Item of earthing includes the cost of 7.5 metre long galvanised iron earth wire 4mm size and protection pipe of 15mm bore galvanised iron light grade and earth work.

MM Constructions

Sushil Chauhan

Pardeep Furnishers and Interiors

Eshaan Construction Co.