CONSTRUCTION OF INSPECTION BUNGALOW AT KARJAN COLONY, TA.ANKLESHWAR DIST : BHARUCH.

NAME OF WORK: CONSTRUCTION OF INSPECTION BUNGALOW AT KARJAN COLONY, TA.ANKLESHWAR

DIST : BHARUCH.

BILL OF QUANTITIES

Percentage Rate Tender

Estimate Rate Amount

Item Description Unit

1 Excavation for foundation upto 1.5 m depth including 1038.73 Cum 203.83

sorting out and stacking of useful materials and disposing

off the excavated stuff upto 50 Meter lead. for Loose or

2 Excavation for foundation for depth from 1.5 m to 3.0 m 981.73 Cum 282.85

including sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter lead for

Dense or Hard soil

3 Providing and laying cement concrete 1:3:6 (1-Cement : 3- 119.55 Cum 2,965.76

coarse sand : 6- hand broken stone aggregates

mmnominal size) and curing complete excluding cost of

formwork in Foundation and Plinth

4 Providing and laying controlled cement concrete M.250 286.81 Cum 4,643.98

and curing complete including the cost of formwork and

reinforcement for reinforced concrete work in

Foundations, footings, Base of columns and Mass

Providing and laying controlled cement concrete M.250

and curing complete including the cost of formwork and

excluding cost of reinforcement for reinforced concrete

work in Columns, Pillars posts and struts, For Ground Floor

6 Filling available excavated earth (excluding rock) in 1414.32 Cum 130.39

trenches. plinth, sides of foundations etc. in layers not

exceeding 20 cm. in depth consolidating each

disposited layer by ramming and watering.

Providing and laying controlled cement concrete M.250

and curing complete including the cost of formwork and

excluding cost of reinforcement for reinforced concrete

work for Ground Beam and SOG Beam

8 Brick work using common burnt clay building bricks having 90.14 Cum 4,021.02

crushing strength not less than 35 kg./Sq.Cm. in foundation

and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand)

(Conventional Brick)

(i) Half brick masonry in common brunt clay building bricks

having crushing strength not less than 35 Kg/Sq.Cm. in

Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in

foundation and plinth (B) Conventional

9 Filling in foundation and plinth with murrum or selected 616.96 Cum 289.06

soil in layers of 20cm. thickness including watering,

ramming and consolidating etc. complete.

10 Providing and laying controlled cement concrete M.150 for 147.97 Cu.m 4,271.29

curing complete including cost of formwork and excluding

cost of reinforcement for reinforced concrete work for

Providing and laying controlled cement concrete M.200

and curing complete including the cost of formwork and

reinforcement for reinforced concrete work in GF Staircase

12 Brick work using common burnt clay building bricks having 212.46 Cum 4,289.33

crushing strength not less than 35 kg./Sq.Cm. for GF

Cement Mortar 1:6 (1- Cement : 6 -fine sand)

(Conventional Brick)

13 (i) Half brick masonry in common brunt clay building bricks 177.25 Sqm 651.67

having crushing strength not less than 35 Kg/Sq.Cm. for GF

in Cement mortar 1:4 (1- Cement : 4 -coarse sand )

(Conventional Brick)

Providing and laying controlled cement concrete M.250

and curing complete including the cost of formwork and

reinforcement for reinforced concrete work in SOG Slab

Providing and laying ordinary cement concrete 1:2:4 (1-

Cement 2- coarse sand : 4- graded stone aggregates 20 mm

nominal size) for R.C.C lintel including finishing smooth

with,curing etc. complete including the cost of formwork

but excluding the cost of reinforcement for Ground Floor

Providing and laying cement concrete 1:2:4 (1- Cement : 2-

Coarse sand : 4- graded stone aggregates 20 mm nominal

size) for reinforced concrete Chhajjas not exceeding 10cm.

thickness upto floor two level including finishing the

exposed surfaces with cement mortar 1:3 (1-cement, 3 Fine

sand) to give a smooth and even surface centering and

formwork and curing complete excluding cost of

reinforcement for Ground Floor

Providing and laying controlled cement concrete M.250

and curing complete including the cost of formwork and

excluding cost of reinforcement for reinforced concrete

work for RCC Walls in lift, Elevation

17 Providing TMT Bar FE 500D reinforcement for R.C.C. work 83511.86 kg 76.21

including bending, binding and placing in position complete

for Ground Floor

18 Providing and laying controlled cement concrete M.250 35.26 Cum 7,801.95

and curing complete including the cost of formwork and

excluding cost of reinforcement for reinforced concrete

work in Columns, Pillars posts and struts For SOG to

19 Providing and laying controlled cement concrete M.250 53.24 Cum 6,565.40

and curing complete including the cost of formwork and

excluding cost of reinforcement for reinforced concrete

work for Terrace Beam

20 Providing and laying controlled cement concrete M.200 2.67 Cum 6,801.74

and curing complete including the cost of formwork and

reinforcement for reinforced concrete work in Staircases

excluding landing for First Floor

21 Brick work using common burnt clay building bricks having 198.79 Cum 4,329.82

crushing strength not less than 35 kg./Sq.Cm. in Mortar 1:6

(1- Cement : 6 -fine sand) (Conventional Brick) for First

(i) Half brick masonry in common brunt clay building bricks

having crushing strength not less than 35 Kg/Sq.Cm. in

Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in

foundation and plinth (B) Conventional.First Floor

Providing and laying controlled cement concrete M.250

and curing complete including the cost of formwork and

reinforcement for reinforced concrete work in Terrace Slab

Providing and laying ordinary cement concrete 1:2:4 (1-

Cement 2- coarse sand : 4- graded stone aggregates 20 mm

nominal size) for R.C.C lintel including finishing smooth

with,curing etc. complete including the cost of formwork

but excluding the cost of reinforcement.First Floor

25 Providing and laying cement concrete 1:2:4 (1- Cement : 2- 3.01 Cum 6,373.38

Coarse sand : 4- graded stone aggregates 20 mm nominal

size) for reinforced concrete Chhajjas not exceeding 10cm.

thickness including finishing the exposed surfaces with

cement mortar 1:3 (1-cement, 3 Fine sand) to give a

smooth and even surface centering and formwork and

curing complete excluding cost of reinforcement for First

Providing and laying controlled cement concrete M.250

and curing complete including the cost of formwork and

excluding cost of reinforcement for reinforced concrete

work for RCC Walls in lift, Elevation for First Floor

26 Providing TMT Bar FE 500D reinforcement for R.C.C. work 31377.51 kg 77.21

including bending, binding and placing in position complete

for First Floor

27 Providing and laying controlled cement concrete M.250 8.94 Cum 7,878.10

and curing complete including the cost of formwork and

excluding cost of reinforcement for reinforced concrete

work in Columns, Pillars posts and struts, for Terrace to

Stair cabin Top slab

28 Brick work using common burnt clay building bricks having 37.19 Cum 4,370.31

crushing strength not less than 35 kg./Sq.Cm. in Cement

Mortar 1:6 (1- Cement : 6 -fine sand) (Conventional Brick)

for Stair Cabin

(i) Half brick masonry in common brunt clay building bricks

having crushing strength not less than 35 Kg/Sq.Cm. in

Cement mortar 1:4 (1- Cement : 4 -coarse sand ) in

foundation and plinth (B) Conventional.Stair Cabin Level

Providing and laying ordinary cement concrete 1:2:4 (1-

Cement 2- coarse sand : 4- graded stone aggregates 20 mm

nominal size) for R.C.C lintel including finishing smooth

with,curing etc. complete including the cost of formwork

but excluding the cost of reinforcement for Stair cabin

30 Providing and laying cement concrete 1:2:4 (1- Cement : 2- 0.34 Cum 6,411.46

Coarse sand : 4- graded stone aggregates 20 mm nominal

size) for reinforced concrete Chhajjas not exceeding 10cm.

thickness including finishing the exposed surfaces with

cement mortar 1:3 (1-cement, 3 Fine sand) to give a

smooth and even surface centering and formwork and

curing complete excluding cost of reinforcement. for Stair

31 Providing and laying controlled cement concrete M.250 6.69 Cum 6,603.48

and curing complete including the cost of formwork and

excluding cost of reinforcement for reinforced concrete

work in Stair cabin beam

32 Providing and laying controlled cement concrete M.250 69.31 Cu.m 6,142.92

and curing complete including the cost of formwork and

reinforcement for reinforced concrete work in Stair cabin

Providing and laying controlled cement concrete M.250

and curing complete including the cost of formwork and

excluding cost of reinforcement for reinforced concrete

work for RCC Walls, Lift, Parapet, Pardi Stair cabin level

34 Providing TMT Bar FE 500D reinforcement for R.C.C. work 11223.78 kg 78.21

including bending, binding and placing in position complete

for terrace floor and stair cabin

20mm thick sand faced cement plaster on walls upto height

10 metres above ground level consisting of 12mm thick

backing coat of C.M. 1:3 (1-cement : 3-sand) and 8mm thick

finishing coat of C.M. 1:1 (1-cement : 1-sand) etc. complete.

Providing 15mm thick cement plaster in single coat on

Rough (Similar)side of single or half brick walls for interior

plastering and finished even and smooth in (ii) Cement

mortar 1:4 (1-cement :4-sand) for Ground Floor

Providing 15mm thick cement plaster in single coat on

Rough (Similar)side of single or half brick walls for

plastering and finished even and smooth in (ii) Cement

mortar 1:4 (1-cement :4-sand) for Ground Floor Ceiling

Providing 15mm thick cement plaster in single coat on

Rough (Similar)side of single or half brick walls for interior

plastering and finished even and smooth in (ii) Cement

mortar 1:4 (1-cement :4-sand) for First Floor

39 Providing 15mm thick cement plaster in single coat on 756.81 Sq.m 214.60

Rough (Similar)side of single or half brick walls for

plastering upto floor two level and finished even and

smooth in (ii) Cement mortar 1:4 (1-cement :4-sand) for

First Floor Ceiling

40 Providing 15mm thick cement plaster in single coat on 221.60 Sq.m 212.54

Rough (Similar)side of single or half brick walls for interior

plastering and finished even and smooth in (ii) Cement

mortar 1:4 (1-cement :4-sand) Stair Cabin

Providing 15mm thick cement plaster in single coat on

Rough (Similar)side of single or half brick walls for

plastering and finished even and smooth in (ii) Cement

mortar 1:4 (1-cement :4-sand) Stair Cabin Ceiling

42 Applying 2 coat of Primer Coat of approved brands on 2333.83 Sq.m 50.50

exterior surface with proper cleaning etc. Item to be

approved by engineer incharge or consulting engineer

43 Finishing walls with textured ( Rustic ) pattern on exterior 18.98 Sq.m 303.00

plastered surface pattern to be approved with consulting

engineer or Engineer Incharge

44 Finishing wall with weather proof exterior emulsion paint 2333.83 Sq.m 114.53

on wall surface (two coats) to give an required shape even

shade after thoroughly brushing the surface to remove all

dirt, and remains of loose powdered materials.etc

45 Applying two coats of putty & two coats of primer of 5564.85 Sq.m 40.59

approved brand and manufacture on new wall surface to

give an even shade including thoroughly brushing the

surface free from mortar dropping and other foreign

matter and sand papered smooth.

46 Wall painting (two coats) with plastic emulsion paint of 4399.24 Sq.m 78.90

approved brand and manufacture on undecorated wall

surface to give an even shade including throughly brushing

the surface free from mortar droppings and other foreign

matter and sand papered smooth.

Ceiling painting (two coats) with plastic emulsion paint of

approved brand and manufacture on undecorated wall

surface to give an even shade including throughly brushing

the surface free from mortar droppings and other foreign

matter and sand papered smooth.

Extra over item 57 for painting with plastic emulsion paint

of approved brand on ceilings and sloping roofs.

Supply and application of FREEFORM STONECRETE ( Vyara

Tiles or equivalent ) with 8-10 mm thickness with max

aggregate size 3-8 mm with compressive strength>

N/mm2, Flexural Strength > 3 N/mm2, Bulk density -1250

kg/m3, and 17% of total mix by weight ( water ) as directed

engineer incharge or consultant

Providing and fixing powder coated aluminium louvres

made from heavy duty extruded aluminium sections

conforming to IS 733 and IS 1285 or equivalent, comprising

heavy aluminium frame and louvre blades of minimum

mm thickness fixed at suitable angle for ventilation while

preventing entry of rainwater, finished with polyester

powder coating of approved shade with minimum 60–80

microns thickness, including fabrication, cutting, drilling,

fixing with stainless steel screws, anchor fasteners,

brackets, sealant and all necessary accessories, scaffolding,

labour, materials, tools and equipment required for proper

installation at site, complete in all respects and measured

in square metres of finished surface area.

Providing and fixing natural stone cladding for building

elevation using approved quality machine cut stone slabs

of required size and minimum 18–20 mm thickness, fixed

on external walls/elevation over backing surface with

suitable stainless steel cramps, pins or brackets and cement

mortar (1:4) as required to ensure proper anchorage,

including dressing of stone edges, maintaining uniform

joints, filling joints with white/grey cement slurry mixed

with matching pigment, scaffolding, curing and all labour,

materials, tools and accessories complete, conforming to

relevant provisions of IS 1597 (Part 1) and IS

complete in all respects and measured in square metres of

finished surface area.

Providing and laying Machine cut free edges machine

polished telephone black madras Granite stone slab 18mm

(Average ) thick ( Single Piece not more than 150cm) for

stair steps and risers & Door/window frame, top of parapet

as per design including full moulded round front steps &

1cm nosing & necessary groove on trads of steps ;laid on

20mm thick cement mortar 1:6 ( 1 cement : 6 coarse sand )

jointed with gray cement sluury including rubbing and

polsihing etc. complete.

Providing and Fixing door made up of 50 mm thickness (

19mm thick 2 nos Ply+12mm thick 1 Ply)both side

laminated and on both side 1 mm thick premium Laminate

with alll fixtures like aldrop,SS Handle,stopper,tadi,door

magnet, door stopper hinges, etc materials as per drawing

& as directed by engineer incharge.Item to be approved by

engineer incharge or cunsulting engineer

Providing and Fixing flush door both side laminated &

I.T.W. beading all around by using I.T.W. frame 120 mmX

80 mm shutter fabricated from 35 mm thick solid core

malemine faced three layered pre laminated flat pressed

wood based exterior grade bonded BWP/BWR synthetic

resin having stamped IS 12823 grade I type II including

three coats of lacquer polishing to exposed wooden surface

& stainless steel decorative type designs fixtures/ fastening

etc including I.T.W trinagular batten patti of size 30mm X

30mm etc as per architectural detailed drawing & as

directed by engineer incharge.

Providing and Fixing Sliding door with Flush Door Shutter

and 1mm thick laminate sheet along with Accessories like

wheel rail, channel, lock with labour, material and other

cost. Item to be approved by engineer incharge

Providing and fixing window having extruded aluminum

Colour anodized section frame main outer size 127mm x

38.10mm x 1.35mm @wt. 1.384kg/m, horizontal Four track

member size 122.20mm x 31.75mm x 1.10mm@ wt

kg/m, vertical member of size 122.20mm x 31.75mm x

1.50mm @1.398 kg/mt with sliding shutters of horizontal

member size 40mm x 18mm x 1.29mm@ 0.456kg/mt

,vertical member of size 40mm x 18mm x 1.29mm @

kg/mt with 5 mm thick transparent bronze colour tinted

float glass with powder coated aluminum fittings and

fixtures and transparent silicon sealant glass fixing to frame

in 3 tracks and in one track mosquito net have to be fit as

per details etc complete for window.

Providing and fixing window having extruded aluminum

Colour anodized section frame main outer size 95mm x

24mm x 1.17mm (of Jindal Section no:2459 @ wt.of

Kg/mt), horizontal Three track member size 92mm x

31.75mm x 1.30mm (of Jindal Section no:8688,@ Wt.1.07

Kg/mt), vertical member of size 92mm x 31.75mm x

1.50mm (of Jindal Section no:8933,@ Wt. 1.06 Kg/mt) with

sliding shutters of horizontal member size 40 mmx18mm

x1.29mm (of Jindal Section no:8947@ wt.of 0.456 Kg/mt),

vertical member of size 40mm x 18mm x 1.29 mm (of Jindal

Section no:8949 @ wt.of 0.456Kg/mt/ with 5 mm thick

transparent bronze colour tinted float glass with powder

coated aluminum fittings and fixtures and transparent

silicon sealant glass fixing to frame in two tracks and in one

track mosquito net have to be fixed as per details etc

Providing and fixing standared extruded of alluminium

section of size 63mm x 38.10mm x 1.2mm (Jindal Section

:2434, @ Wt. 0.643 Kg/mt) with colour anodized

alluminium frame for ventilation with 5 mm thick frosted

glass as details etc complete for Ventilation

58 Providing and fixing M.S. grills of required pattern to 6014.79 Kg 105.18

wooden frames/grenite frames of windows etc. with M.S.

flats at required spacings and frame alround, square or

round bars with round headed bolts and nuts or by screws

(A) Plain Grill.

59 Painting two coats (excluding priming coat) on new steel 200.49 Sqm 87.81

and other metal surface with enamel paint, brushing,

interior to give an even shade including cleaning the

surface an even shade including cleanicn the surface of all

dirt, dust and other foreign matter.

60 Providing and fixing frameless glass railing made of 79.52 Sqm 11,766.50

toughen glass ( 12 mm thick ) with rail guide on top at

every 2' C/C made up of 2" SS 304 pipe with all necessory

fixtures ( steel balustrades ), labour, material. Item to be

approved by engineer incharge

P & L 800mm x 1600 mm vitrified 9 mm thick tile flooring

over 20 mm (average) base of cement mortar 1:6 (

cement: 6 coarse sand) on new surface or fixing on existing

flooring by adhesive material including dismentaling of

existing flooring and jointed with color cement slurry

including finised with flush pointing & cleaning the surface

etc. complete for light shade Glossy. Item to be approved

by engineer incharge

62 P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm 183.97 Sq.m 1,415.77

(average) base of cement mortar 1:6 ( 1 cement: 6 coarse

sand) on new surface or fixing on existing flooring by

adhesive material including dismentaling of existing

flooring and jointed with color cement slurry including

finised with flush pointing & cleaning the surface etc.

complete for light shade. Item to be approved by engineer

63 Providing and laying coloured glazed tiles of the size 300 656.65 Sq.m 1,417.36

skirting, risers of steps and dedo on 10 mm. thick cement

plaster 1:3 (1 cement : 3 coarse sand) & jointed with white

P & L 24" x 24" vitrified 8 mm thick tile flooring over 20 mm

(average) base of cement mortar 1:6 ( 1 cement: 6 coarse

sand) on new surface or fixing on existing flooring by

adhesive material including dismentaling of existing

flooring and jointed with color cement slurry including

finised with flush pointing & cleaning the surface etc.

complete for antiskit

Providing and laying broken chine mosaic flooring

over avg 40 mm C.C 1:2:4 bedding for maintaning slope for

plain and curve surface & 12 mm to 20 mm broken pieces

of glazed tiles to be laid over cement mortar 1:3 to plain or

slope and to be tempered to bring mortar creme out

upto surface using white cement including rounding off

junctions and extending them upto 15 cm along the

wall,clearing with water and oxalic acid etc. as directed.

Providing and applying waterproofing treatment to toilet

sunken slabs by cleaning the surface thoroughly and filling

the slab with brick bat coba using broken brick bats laid in

cement mortar (1:4) mixed with approved waterproofing

compound such as Dr. Fixit / Fosroc / Sika or equivalent.

The brick bat layer shall be well compacted and finished to

the required slope towards the outlet. Joints and corners

shall be properly sealed, and a waterproof slurry coat of

cement mixed with waterproofing chemical shall be applied

before and after laying brick bats. The finished surface shall

be cured adequately and checked by ponding test for a

minimum of 48–72 hours to ensure complete

watertightness before laying the final floor finish. The work

shall be carried out complete with all materials, labour,

curing, and testing as per standard specifications.

66 Providing Sandwitch Type Platform Using 25mm thick 27.71 Rmt 3,764.27

Single Polished kotah stone 75 cm Width at Top Width

to 18 mm Thick Premium Black Grenite Stone at Top with

75 mm Width and Face Patta Maximum 3.0 Mtr Long In

Single Piece using Cement Mortar 1:4 ( 1 cement : 4 coarse

sand ) laid by 75 cm width & 75 cm High Resting On 25 mm

Thick One Side Polished kotah stone fixed in wallc Cement

Mortar 1:4 ( 1 cement : 4 sand ) at Bottom Polished Kotah

stone flooring including fixing grenite stone & cutting the

stone for Fixing suitable fixtures/ sanitary etc. if required

with Polished & Including Providing Premium Black

Polished Grenite Stone 16 to 18 mm Thick with round

Border the edge,cost of sink. S S Grating Jali for nahni Trap,

Brass Waste Coupline ,PVC Waste Pipe, Manking Grove in

67 Providing 0.75mt wide plinth protection including 171.84 Rmt 991.26

excavation in hard or dence soil and Laying C.C 1:3:6 (1

cement : 3 coarse sand: 6 brickbats/stone aggregates) in

foundation and on top including Curring fnishng etc.

Anti-Termite System:Providing and laying of permanent

piping technology anti-termite treatment before flooring

work by installing LLDP (Low linear density polyethylene)

tube of 8 mm O.D. & 6.4 mm 1.D. with inbuilt pressure

compensation chip every 30 cm interval in the tube, having

working pressure of 2 Kg/cm2 and release rate of

Itr/hour fixed by P-clips and nails. The LLDP pipe shall be

installed at the entire periphery of the building and at

internal network of building at a depth of 20 to 200 mm

under floor at every 2 to 3 mtr. c/c distance (adjusted as

per building layout ) & Ends of loop pass through a PVC

elbow of minimum 32 mm ID at junction box of wall and

floor level, entering into a steel reinforced grooved flexible

pipe of minimum 22 mm ID leading into junction box and

the loops shall terminate in junction boxes & test every

junction during injecting chemicals for termite control

treatment. The anti termite chemical Imidacloprid 30.5% SC

mix as per IS-6313 (part III) shall be injected by the pressure

pump diluted with water @ 10.5 ml/5 ltr of water at the

rate of 2 Kg/sq.cm @ 5 Ltr/SMT. The contractor shall

submit approved line plan for piping system and junction

boxes dully approved by Engineer-in-Charge with bond of

year warranty.(i)Anti Termite chemical injected area

(Chemical injecting incl. labour cost)

69 Providing cement vata (10cm. x 10 cm. size) quarter round 806.61 Rmt 23.68

in cement mortar 1:1 including neat cement finishing,

watering etc. complete.

Providing and fixing wsh down water closet wall hung

matte finish outside and glossy inside (European type, W.C.

Pan) make cera/hindware/Kohler/Jaquar etc or similar with

integral P or S trap including jointing the trap with soil pipe

in Cement Mortar 1:1 (1-Cement : 1-fine sand) with Seal

and cover of size 510X365X380 mm. Item to be approved

by engineer incharge or consulting engineer

71 Providing and fixing 40mm Dual flush cock/valve make 12.00 Each 3,535.00

cera/hindware/Kohler/Jaquar etc or similar with Square

plate made up of ss 304 to control cock operation of

approved quality including fixing in pipe line etc. complete.

Item to be approved by engineer incharge or consulting

72 Providing and fixing Ultra Thin SS Rain Shower make 9.00 Each 6,060.00

cera/hindware/Kohler/Jaquar etc or similar of 300 mm size

in single flow, Item includes all labour, material,

transportation etc. Item to be approved by engineer

incharge or consulting engineer

73 Providing and fixing high flow single lever concealed 9.00 Each 8,080.00

diverter make cera/hindware/Kohler/Jaquar etc or similar

with diverter handle, Item includes all labour, material,

transportation etc. Item to be approved by engineer

incharge or consulting engineer

74 Providing and fixing 12 mm thick toughen glass with 54.95 Sqm 2,525.00

necessary fittings and item includes all labour, material,

transportation etc. Item to be approved by engineer

incharge or consulting engineer

Providing and fixing thin rim table top washbasin make

cera/hindware/Kohler/Jaquar etc or similar with single hole

for pillar tap with C.I. or M.S. brackets painted white

including sutting holes and making good the same but

excluding fittings.(A) Vitreous China:(ii) Flat Back washbasin

550 mm x 380mm size x 110 mm. (i) In white

colour.a)Providing and fixing C.P. brass waste for washbasin

or sink. (A) 32mmdia. b)Providing and fixing M.I. fisher

union for washbasin or sink. (A) 32mm dia. c)Providing and

fixing pillar tap, capstan head, screw down high pressure

with screws, shanks and back nuts. (i) 15mm

dia.d)Providing and fixing brass screw down stop tap.(A)

15mm dia.e)Providing and fixing Rubber plug for sink or

Providing and fixing Kitchen sink make

cera/hindware/Kohler/Jaquar etc or similar with C.I. or M.S.

brackets, painted white including cutting holes in walls and

making good the same . (C) Vitreous China Sink.(i) 600mm x

450mm x 150mm size.with fittings(ii) Flat Back washbasin

550 mm x v 400mm size. (i) In white colour.a)Providing and

fixing C.P. brass waste for washbasin or sink. (A) 32mmdia.

b)Providing and fixing M.I. fisher union for washbasin or

sink. (A) 32mm dia. c)Providing and fixing pillar tap, capstan

head, screw down high pressure with screws, shanks and

back nuts. (i) 15mm dia.d)Providing and fixing brass screw

down stop tap.(A) 15mm dia.e)Providing and fixing Rubber

plug for sink or wash basin.

Providing and fixing wall-hung vitreous china urinal of

approved make such as Hindware / Jaquar / Parryware or

equivalent, white glazed finish, size approximately 560 mm

× 350 mm × 300 mm (H × W × D), complete with CP brass

spreader, 32 mm dia flush pipe, inlet connection, waste

coupling, and all necessary fittings. Urinal shall be fixed to

wall with suitable brackets/bolts at required height,

including connection to water supply and waste line,

testing for proper functioning, and making good the wall

surface complete as directed by Engineer-in-Charg

78 Providing and fixing Bib Cock ( Bib Tap ) make 4.00 Each 2,020.00

cera/hindware/Kohler/Jaquar etc or similar with wall flange

& aerator. Item includes all labour, material and other cost.

(ii) 15mm dia. Item to be approved by engineer incharge

Providing and fixing 2-way bib cock / angle valve with

health faucet of approved make such as Jaquar / Hindware

/ Parryware or equivalent, made of high quality chrome

plated brass, wall mounted, 15 mm nominal bore, with

dual outlet arrangement for water supply and health faucet

connection. The item shall include ABS/CP health faucet

with 1.0–1.2 m long flexible hose pipe, wall hook, and all

necessary fittings, complete with fixing, testing and making

good the wall surface as required, all complete as directed

by Engineer-in-Charge

Constructing brick masonry chamber for underground C.I.

Inspection chamber and bends with bricks having crushing

strength not less than 35Kg/Cm2 in C.M. 1:5 C.I. cover with

frame (Light duty) 455mm x 610mm intenal dimensions

total weight of cover with frame to be not less than 38Kg.

(Wt. of cover 23 Kg.) and Wt. of frame 15Kg. ) (R.C.C. top

slabe with 1:2:4 mix (1-cement :2- coarse sand :4-graded

stone aggregate 20mm size) foundation concrete 1:5:10

inside plaster 15mm thick with cement mortar 1:3 finished

smooth with a floating coat of neat cement on walls and

bed concrete etc. complete.(i) Inside dimensions 455mmx

610mm and 450mm deep for single pipe line.

Providing and fixing S.W. gully trap with C.I. grating brick

masonry chamber and water tight C.I. cover with frame of

300mm x 300mm size (inside) with standard weight.(i)

Square mouth traps. (A) 100mm x 100mm size P type.

82 Providing and fixing PVC SWR Nahni trap IS 14735 for drain - 31.00 Each 558.36

100 mm diameter with jali of the following nominal

diameter of self cleansing design with C.I scread down or

hinged grating including the cost of cutting and making

good the walls.

83 Providing laying and jointing in true line and level 15mm 122.40 Rmt 72.65

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or

equivalent as approved by Engineer In Charge. Pipe shall

be fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

84 Providing laying and jointing in true line and level 25mm 161.12 Rmt 91.84

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or

equivalent as approved by Engineer In Charge. Pipe shall

be fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

85 Providing laying and jointing in true line and level 40mm 182.07 Rmt 148.12

dia. U.P.V.C. Pipe ( SCH- 40) for cold water including

fittings make PRINCE / SUPREME / ASTRAL / FINOLEX or

equivalent as approved by Engineer In Charge. Pipe shall

be fixed on the wall with the help of clamp at every two

metre C/C or shall be concelled as directed including

necessary fittings etc. including testing of pipe and joints

and fixing the same with adhesive solvent, including cost

of all materials.

Providing and fixing to wall ceiling and floor 6.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside

Dia. Low densidy, complete with special falnge

compression type fittings, wall clipsetc. including making

good the wall ceiling and floor 75 mm Dia

Providing and fixing to wall ceiling and floor 6.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside

Dia. Low densidy, complete with special falnge

compression type fittings, wall clipsetc. including making

good the wall ceiling and floor 110 mm Dia

Providing and fixing to wall ceiling and floor 6.0 Kg. F/Cm2

working pressure poluthene pipes of the following outside

Dia. Low densidy, complete with special falnge

compression type fittings, wall clipsetc. including making

good the wall ceiling and floor 160 mm Dia

89 Providing and fixing Gun metal check or non-return fullway 15.00 Each 420.63

wheel valve.(C) 25mm dia.

90 Providing and fixing Gun metal check or non-return fullway 4.00 Each 663.43

wheel valve.(E) 40mm dia.

91 Providing and fixing 600mm x 450mm bevelled edge 17.00 Each 833.73

mirrror of superior glass mounted on 6mm thick A.C. sheet

or plywood sheet and fixing to wooden pluge with C.P.

brass screws and washers.

92 Providing and fixing C.P. brass towel rail comlete with C.P. 17.00 Each 603.19

brass brackets fixed to wooden plugs with C.P. brass

scews.(B) 600mm x 20mm size.

93 Providing and fixing C.P. brass shower rose with 15mm or 9.00 Each 282.16

20mm inlet.(A) 100mm dia. Each

Providing and fixing Chicken mesh jali 16X24 (22 gauge) at

the junction of 2 different surfaces of different material

component at the time of plastering to prevent cracking in

plaster surface as and where directed at all floors with all

leads and lifts etc.complete.

95 Providing and fixing Jet spray heavy duty with S.S. Braided 12.00 Nos. 308.99

hose 60 cm long

96 Providing and fixing toilet paper holder.(A) C.P. Brass 12.00 Each 418.68

Providing & Installation of Kitchen furniture of any size

made of 19mm ply ,(BWP Playwood -IS ;710USED) with

outer most Ply having 0.9 mm laminate confirming IS

2046:1995 and inner Ply having regular 0.9 mm thick

laminate confirming IS 2046:1995 with required numbers &

size Handle made of SS etc. at any position in furniture

made up on site as per architects drawing finished without

laminets/veneer ,as per architect's instruction .Rate

includes all joints of ply have to be fixed with S.S screws ,S.S

nails , anti termite treatment ,synthetic resin Adesives

,sticking tapes etc.complete. Items to be approved by

engineer incharge

98 Earthwork for embankment including breaking clods, 6480.00 Cum 337.34

dressing with all lead and lift (including watering ) From

Borrow area within 10.0 Km. lead

Rolling of earthwork in layers with power roller including

filling in depressions which occur during the process.

Providing and fixing pre-cast concrete kerb stone of gray

cement based concrete block 30cm length,30cm height and

15cm thick of M200 grade concret as per approved design

and including excavation for fixing in proper line and

level,filling the joint with C:M 1:3 (1cement:3fine sand) etc

Pro. And fixing single layer water proof gypsum board

mm thick sections using water proof board of size 1220 mm

x 1830 mm x 8.0 mm suspended by GI suspender channel

of size 25 mm x 3 mm with intermediate channel og size

mm x 40 mm x 0.8 mm at 1220 mm center to center ceiling

section of size 40 mm x 35 mm x 0.55 mm at 457 mm c/c

and perimeter channel A of size 20 mm x 27 mm x 30 mm x

0.5 mm at edges & drops incl.paper tap sand sofit cleat,

anchor fastener, scoch bolt connecting cleat,joining

compound top coat on ceiling incl.making necy.opening for

light fitting,diffuser etc. comp. as per detail drawing as

102 ROLLER BLINDS 229.68 Sqm 4,545.00

Providing and Fixing Roller blinds as approved shade &

fabric.the blind shall be made out of extruded aluminium

alloy of 48mm outer dia. With a minimum wall thickness of

1.1mm duly anodised for long life. The tube shall be

designed with support ribs to keep it straight and shall

have a pocket for holding the fabric in position. the

operating mechanisium shall consist of a gear with spring

booster. the mechanisium shall be designed using high

strength fibred glass reinforced polyster assembly and

high carbon steel spring to transmit motion from

driving to driven members. the min. spring torque shall be

16kg per cm to ensure ultra smooth operation of blinds of

up to 3m width and 4m drop. the mechanisum shall

operate with the use of an endless beaded chain. the

endless chain shall be made from 2.3mm polyster cord with

7mm beads. the pitch of the chain shall be 13.5 mm.

an optional stopper shall be provided for stoping the blind

at desire position.idler shall be high strength fibreglass

reinforced polyster consisting of an outside sleev and

centre shaft. sleeve shall provide bearing surface for the

roller tube and provide bearing surface for the roller

tube and rotate freely on the centre shaft, providing

smooth, quiet and long wearing operation. brackets shall

be of optmised steel powder coated to give superior

Providing and fixing concealed center point to wall ceiling

& floor CPVC (SDR 13.5) PIPE having National Sanitation

Foundation (NSF) seal for potable water of following dia.

nominal bore tube fittings and clamps including making

good the wall, ceiling and floor etc. complete.[A] 15 mm.

Providing and fixing interior wall panelling consisting of

framework made of seasoned hardwood battens /

aluminium / GI framing of suitable size fixed to wall with

approved fasteners, including necessary alignment and

spacing to receive panelling boards. The framework shall be

covered with 12 mm thick plywood / MDF board of make

Greenply / CenturyPly / Action TESA or equivalent, finished

with approved decorative laminate of make Greenlam /

Merino / CenturyLaminates, including adhesive, screws,

edge beading, mouldings, polishing or laminate finishing as

required. The work shall include cutting, jointing, grooves,

preparation of surface, filling of gaps, sanding and finishing

complete, including all labour, materials, tools and

incidentals required to complete the wall panelling work in

all respects as per approved drawings and directions of

Engineer-in-Charge.

Providing and fixing pre-cast Rubber Dye / steel Dye inter

locking concrete block 60mm thick with grade of concrete

M300 pnumatic compressed / vibrated mechanically and as

per approved design Confirming to IS 15658 :

including 35 mm Sand layer for levelling and filling the joint

with sand in proper line and level as per guidlines of IRC :

SP 63-2018 etc. Complete.

Providing & Installation of Cup board of size made of 19mm

ply ,(BWP Playwood -IS ;710USED) with outer most Ply

having 1.0 mm laminate confirming IS 2046:1995 and inner

Ply having regular 1.0 mm thick laminate confirming IS

2046:1995 having required number of drawers of different

sizes & heights with necessary handles and locks of

different in size etc. & having 2 sliding door of aluminium

track on top and bottom with surface mounted door

handle at any position in furniture made up on site as per

architects drawing finished .Rate includes all joints of ply

have to be fixed with S.S screws ,S.S nails , anti termite

treatment ,synthetic resin Adesives ,sticking tapes

etc.complete. Items to be approved by engineer incharge

Providing & Installation of Cup board made of 19mm ply

,(BWP Playwood -IS ;710USED) with outer most Ply having

1.0 laminate confirming IS 2046:1995 and inner Ply having

regular 1.0 mm thick laminate confirming IS 2046:1995

having drawers of different sizes with necessary handles of

different sizes and locks etc. & having required number of

doors with required number of door handle at any position

in furniture made up on site as per architects drawing

finished .Rate includes all joints of ply have to be fixed with

S.S screws ,S.S nails , anti termite treatment ,synthetic resin

Adesives ,sticking tapes etc.complete. Items to be approved

by engineer incharge

Providing & Installation of Kitchen cabinet with 5 kg

hydraulic gas spring soft close made of 19mm ply ,(BWP

Playwood -IS ;710USED) with outer most Ply having 1.0 mm

laminate confirming IS 2046:1995 and inner Ply having

regular 1.0 mm thick laminate confirming IS 2046:1995

having 5 mm thick fluated glass on front with aluminium

shutter profile at any position in furniture made up on site

as per architects drawing finished .Rate includes all joints of

ply have to be fixed with S.S screws ,S.S nails , anti termite

treatment ,synthetic resin Adesives ,sticking tapes

etc.complete. Items to be approved by engineer incharge

Providing & Installation of Kitchen cabinet made of 19mm

ply ,(BWP Playwood -IS ;710USED) with outer most Ply

having 1.0 mm laminate confirming IS 2046:1995 and inner

Ply having regular 1.0 mm thick laminate confirming IS

2046:1995 having 5 mm thick fluated glass on front with

aluminium shutter profile at any position in furniture made

up on site as per architects drawing finished .Rate includes

all joints of ply have to be fixed with S.S screws ,S.S nails

anti termite treatment ,synthetic resin Adesives ,sticking

tapes etc.complete. Items to be approved by engineer

Providing & Installation of TV Unit made of 19mm ply

,(BWP Playwood -IS ;710USED) with outer most Ply having

1.0 mm laminate confirming IS 2046:1995 and inner Ply

having regular 1.0 mm thick laminate confirming IS

2046:1995 with necessary partitions and handles in

required in size etc. at any position in furniture made up on

site as per architects drawing finished .Rate includes all

joints of ply have to be fixed with S.S screws ,S.S nails , anti

termite treatment ,synthetic resin Adesives ,sticking tapes

etc.complete. Items to be approved by engineer incharge

Providing and fixing Mangalore pattern clay tiles of

approved make such as Mangalore Tiles or equivalent, size

approximately 400 mm × 250 mm, for elevation cladding,

fixed over a framework of MS angles / vertical and

horizontal battens (minimum 25 mm × 25 mm or as

required) securely anchored to the wall with suitable

fasteners and holdfasts. The work shall include providing a

waterproof backing layer using polymer modified

waterproof coating / waterproof membrane over the wall

surface prior to fixing the framework to prevent seepage.

Tiles shall be fixed with GI screws/hooks and binding wire

maintaining proper alignment, uniform overlap, and

spacing as per approved pattern. The item shall also

include necessary cutting of tiles, corrosion protection to

MS members with primer and paint, sealing of joints where

required, scaffolding, and all labour and materials,

complete to achieve a neat architectural finish as per

drawings and direction of the Engineer-in-Charge.

112 Providing erecting and fixing double coated ISI water tank 4.00 Sqmtr 3.95

of required capacity each with all necessary fittings and

connection etc. complete on terrace

113 Providing and fixing 1 Hp Pressure booster pump of brand 4.00 Each 30,300.00

equivalent to Kirloskar with automatic water level

controller of brand equivalent to Crompton including all

electric wire and connection material and labor for fixing

with existing pipe connection and tank etc with all lead and

114 Excavation for foundation upto 1.5 m depth including 6.00 Cu.m. 268.28

sorting out and stacking of useful materials and

disposing off the excavated stuff upto 50 Meter

lead.(B) Dense or Hard soil

115 Excavation for foundation for depth from 1.5 m to 3.0 6.48 Cu.m. 289.92

m including sorting out and stacking of useful

materials and disposing off the excavated stuff upto

50 Meter lead.(B) Dense or Hard soil

Brick work using common burnt clay building bricks having

crushing strength not less than 35 kg./Sq.Cm. in foundation

and plinth in Cement Mortar 1:6 (1- Cement : 6 -fine sand)

(Conventional Brick) For Honey Comb Work

117 Filling in foundation and plinth with brick Bats Chhara 4.18 Cu.m. 615.57

in layers of 20cm. thickness including watering,

remming and consolidating etc. complete. With 5 km

118 Supplying Kapchi of 25mm to 40mm with 5 km lead 1.36 Cu.m. 469.65

119 Suppplying B.T. Kapchi 10mm to 20mm size with 5 2.16 Cu.m. 569.45

120 Suppplying coarse sand with 5 km lead… 6.48 Cu.m. 289.14

121 Drilling bore 175mm dia upto 35mt depth… 35.00 Rmt. 353.50

122 Providing & Installation of UPVC casing pipe of 6" 35.00 Rmt. 1,079.77

123 Labour charges for filling kapchi / Grit brick bat/ sand 1.00 Job 1,010.00

etc in layers as directed…

124 Preparing structural design of RCC Under Ground / 20000.00 Ltr. 5.98

Partially under ground / above high ground level

Reservoir of required capacity as per relevant I.S.

standards and Constructing the same, including

excavation in all types of soil strata (including rock)

including shoring strutting if required, for loose soil /

to protect from collapse, casting 100 mm thick P.C.C.

levelling course in M- 15, Refilling the pit with proper

soil and disposing of the surplus stuff at all lead.

Including cement plaster in CM 1:2 with approved

water proofing compound to all over inside container

(i.e. walls, base, top slab/dome bottom etc. all).

Including all types of labour and material charges of

lowering, laying, erecting / hosting and jointing of

pipe assembly to inlet, outlet overflow, washout and

bye pass arrangement as per hydraulic design.

Providing and fixing accessories, CI Manhole frame

and cover, water level indicator, adequate cowl type

ventilators or lantern type ventilator with stainless

steel jail. RCC chambers for valves. Providing and

applying three coats of cement paint / snowcem to

the out side face of structure. It also includes

satisfactory water tightness test as per relevant I.S.

code and painting name of scheme and capacity on

the tank as per direction of engineer in charge.

List of Indian Standards for Design of GSR / SUMP:-

The structural design of GSR shall be in accordance

with provisions relevant I.S standards (1) I.S.

part I & II 2009 or Its latest revision (1.1) I.S.

part III & IV 1965 or Its latest revision (2) I.S. 456 –

2000 or Its latest revision. (3) I.S. 1893 – 2000 –

or Its latest revision. (4) I.S. 875, Part – 1 to 3, 1987 or

Its latest revision.

General Specifications:- (1) Water depth in container

shall be adopted as per data of tender. Capacity shall

be calculated excluding free board of the reservoir. If

water depth is not specified, the suitable water depth

/ acceptable to field engineer in accordance with

hydraulic requirement (2) Shape of container (in

plan)specified by in data shall be adopted in absence

circular shape shall be adopted (3) Size shall be fixed

as per availability of space (land area) at site /

acceptable engineer in charge. (4) Effect of

overlapping of pressure bulbs on soil due near by

structure and proposed sump should be considered.

(5) Care shall be taken that no damage should occur

to nearby existing structure. Compensation shall be

paid for the same by agency. (6) The minimum

concrete grade for RCC shall be M-30. (7) HYSD Fe

415 / 500 grade reinforcing bars confirming to I.S.

1786 / 1139 shall be considered in design. CRS / TMT

bars shall be provided. In saline atmosphere

corrosion resistance stainless steel / HCR rebar shall

be provided. Any other steel can be used with

approval of C.E./ in situation of non availability in

market without extra cost.

(8) Minimum size (or thickness) of various

components shall be provided as per tender criteria /

specifications in absence as per I.S./ Std. practice of

G.W.S.S.B. Minimum dimensions specified for various

components in tender data / specifications shall be

provided without fail. (9) The safe bearing capacity

(SBC) shall be referred from SBC test report. In

absence of report it shall be referred from data sheet.

If poor soil is found / water table is met with during

excavation SBC shall be scientifically ascertained and

design shall be revise. No extra shall be paid for

increase in quantity. (10) DI pipes and special shall

only be used if type is not specified in tender. (11)

The rate shall include cost of dewatering during

excavation making all arrangement when water table

meets within depth.

(12) The structure shall be designed properly to resist

uplift due to ground water table specified in data or

actual ground water table meets with during

excavation. If GWT / Uplift is mentioned in tender

and during excavation it dose not meet 7.5% rate

shall be reduced. (13) SS pipes railing shall be

provided over sump perifery when sump height is ≥

1.5 meter above ground level. (14.a) RCC

staircase/RCC Steps should be provided from GL to

sump top slab based on the height of the GSR

above/below the ground. (14.b) RCC Staircase with SS

railing to be provided inside reservoir container. BB

Masonry staircabin to be provided to cover the same

with MS safety door having locking arrangement. (15)

Appearance of structure should be aesthetically good

looking acceptable to authority. (16) Any change in

size, shape, depth below GL, height above GL, water

depth, F.B., size of member etc can be permitted in

exceptional case due to site condition or hydraulic

design requirement by C.E. No extra shall be paid for

(17) Any change in data, dimensions, shape, water

depth, reduction in size if permitted by competent

authority and if it reduces quantity then payment

shall be reduced prorate. (18) When capacity of GSR /

Sump is > 20 lakh litres two or suitable compartments

acceptable to executive engineer shall be designed

and provided. (19) Agency shall engage qualified (at

least graduate) consulting engineer for designing the

structure and he / she shall visit the site for guidance

of work. (20) 75% part rate shall be payable for

concrete, reinforcement and plastering items of

container until satisfactory hydraulic testing for water

tightness is performed as per tender condition. Till

the work shall be treated as incomplete. Above

conditions / general specifications Sr. No. 1 to 20 are

part and parcel of tender (contact) and prevail over

other provisions in tender. D) As above rectangular

sump with water table (Sub soil water level above

foundation) 1) 20000 Ltr Capacity Cost of 20000 Ltr

Point wiring for Light / Bell with 2-1.5 sq.mm & earth

wire of 1.5 sq.mm (Green) both are of ISI marked 1.1 KV

grade FRLS PVC insulated multi strand copper wires up to

10 mtr length , in below type of pipe erected with 6A

Modular type switch / bell push & accessories and earth

continuity of following type, erected on PVC /

Metallic/Wooden box, single mounting base frame

covered with textured/metallic/white front plate modules

erected on / in wall / ceiling as per pipe erected, with

necessary Lamp holder/ceiling rose / H.D.Connector as

directed. (f) with medium class Rigid PVC pipe and

accessories erected concealed in wall/ceiling complete Cat.

Point wiring for Fan/Exhaust with 2-1.5 sq.mm & earth

wire of 1.5 sq.mm (Green) both are of .ISI marked 1.1 KV

Grade FRLS PVC insulated multi strand copper wires up to

10 mtr length, in below type of pipe erected with 6A

Modular type switch and hum free EME step type

electronic fan regulator mounted and accessories with

earth continuity of following type erected on PVC /

Metallic/ Wooden box, single mounting base frame

covered with textured/metallic/white front plate modules

erected on / in wall / ceiling as per pipe erected. with

necessary ceiling rose / H.D.Connector as directed. (f) with

medium class Rigid PVC pipe and accessories erected

concealed in wall/ceiling complete Cat. III

Point wiring for on board Looped Plug with 6A Modular

type switch & 5 pin socket erected on PVC /

Metallic/Wooden box, single mounting base frame covered

with textured / metallic/white front plate modules erected

on / in wall / ceiling with following type accessories Cat. III

Point wiring for Individual Plug with & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multi strand copper wires up to 10 mtr

length, in below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate

modules erected on / in wall / ceiling as per pipe erected

with following type of accessories.

[I] For 6A Plug and 6 a switch with 2-1.5 sq.mm Cu. Wire

from nearby switchboard/mcb db board

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete

Point wiring for Individual Plug with & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multi strand copper wires up to 10 mtr

length, in below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate

modules erected on / in wall / ceiling as per pipe erected

with following type of accessories.

[III] For 16A Plug and 16 amp switch with 2-2.5 sq.mm Cu.

Wire with 2.5 sq.mm ( green) earthing wire from mcb d b

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete

Point wiring for Individual Plug with & earth wire of

sq.mm (Green) both are of ISI marked 1.1 KV grade FRLS

PVC insulated multi strand copper wires up to 10 mtr

length, in below type of pipe erected complete with

Modular type switch & 5 pin Plug erected on PVC /

Metallic/Wooden box covered with appropriate front plate

modules erected on / in wall / ceiling as per pipe erected

with following type of accessories.

[III] For 16A Plug and 16 amp switch with 2-4 sq.mm Cu.

Wire with 2.5 sq.mm ( green) earthing wire from mcb d b

(f) with medium class Rigid PVC pipe and accessories

erected concealed in wall/ceiling complete

Providing following type of Modular Type Accessories

mounted with PVC / metallic/Wooden box, single mounting

base frame covered with textured / metallic/white front

plate , modules erected with necessary connections as per

site situation directed by Engineer In charge. (3) Two Pin/RJ-

11 Telephone Socket [A] For One Gang- Cat. III

132 (4) TV Co-axial Socket outlet [A] For One Gang- Cat. III 14 Each 160.59

133 (11) 6 Amps. Bell Push 9 Each 151.50

134 (20) Modular Buzzer 9 Each 149.48

Providing and erecting Sheet Steel powder coated Vertical

MCB distribution board (VTPN) - flush / surface mounted

double door (IP54) fitted with copper insulated busbar,

isolated neutral bar, earth bar and DIN rail, Conforms to IS

8623-1 & 3, IEC 61439-1 & 3, suitable for 63/100 AMP TPN

MCCB + RCCB as incomer and three phase outgoing as per

following .(The DBs should be used of same company of

MCB to be used) (B) 6 way outgoing

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to IS

8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of same

company of MCB to be used) suitable for

(B) three phase incoming and single phase horizontal type

outgoing Per phase isolation type (PPI)

(b) sheet steel double door

Providing and erecting Sheet Steel powder coated MCB

distribution board - flush / surface mounted fitted with

busbar, neutral link, earth bar and DIN rail, Conforms to IS

8623-1 & 3, IEC 61439-1 & 3 without MCB to house

appropriate nos. of MCBs.(The DBs should be used of same

company of MCB to be used) suitable for (A) single phase

incoming and horizontal single phase outgoing (b) sheet

steel double door (IP-43) (iii) 8 way

138 diito as above but (iii)12 way 4 Each 1,492.78

Providing and erecting Approved make Four pole moulded

case circuit breaker having breaking capacity ICU of 35 KA.

at 415 V. having Normal current rating 200A.with variable

Thermal & magnetic release suitable to work on A.C.supply

50 c/s. with all internal connections, spreader tinned

copper & complete erected in existing 16 G.M.S.housing

Providing and erecting Approved make RCCBs conforming

to IS: 12640 and having sensitivity of 30 mA and Short

Circuit withstand capacity of 10 KA and suitable for

operation on 3 phase and neutral 415V,50Hz. having

characteristic of quick action & tripping with all advance

feature & do not incorporate any electronic component for

following Max. rating erected as directed. (iii) 63 Amps. FP

141 diito as above but (ii) 40 Amps. FP 3 Each 2,637.11

providing and erecting Approved make RCCBs conforming

to IS: 12640 and having sensitivity of 30 mA and Short

Circuit withstand capacity of 10 KA and suitable for

operation on single phase 240 V,50Hz. having characteristic

of quick action & tripping with all advance feature & do not

incorporate any electronic component. for following Max.

rating erected as directed (ii) 40Amps. DP

143 diito as above but (i) 25Amps. DP 5 Each 1,969.50

144 Providing & erecting 415 V MCB three Pole for Motor & 1 Each 716.09

Inductive Load (C Curve) having 10KA breaking capacity &

confirms to IS :8828 in existing box having following

capacity (c ) 63 Amp.

145 diito as above but (b) 40 Amp. 3 Each 647.41

providing and erecting Miniature circuit breaker single pole

6A to 25A suitable to operate on 240 V A.C. system and

having breaking capacity 10 KA to be erected in existing

box. confirming to IS 8828/1996 with ISI Mark Cat. III

147 Providing & erecting 240 V MCB double pole switch for 4 Each 330.27

motor & inductive load (C Curve) having 10 KA breaking

capacity & confirms to IS : 8828 in existing box having

following capacity (B) 40 Amp.

Supplying & erecting in earthpit of minimum bore dia.

225mm size approved make Safe Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-1987

made of corrosion free hot dipped G.I.Pipes having Outer

pipe dia of 80 mm having 80-200 Micron galvanising, Inner

pipe dia of 40 mm having 200-250 Micron galvanising,

connection terminal dia of 14 mm with constant ohmic

value surrounded by highly conductive compound with

high charge dissipation suitable for following type of

applications with chamber and heavy duty

cover.(approved make OEM has to submit test certificate

including value of earth resistane of installation. [A] For

electrical installation up to 440 V Length of Pipe - 1 Mtr

Back filling compound - 1 Nos. of Bag of 15 Kgs.

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/CRCA/ aluminium die cast

powder coated and high U.V. & corrosion resistance with

diffuser with company mark/name 160V to 270V, Power

Factor more than 0.9, THD < 15%, CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt, LED driver efficiency >

85 % ( fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage capacity

of LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (A) Tube

Light with integral driver (iii) 18-20 Watts, Surge - 2KV,IP-

20, conventional 4 feet Cat. III

Supplying and erecting led lamps with following wattage

capacity of 220 to 240 voltage, minimum 15000 burning

hours life, 500 V in built-surge protection,Polycarbonate

diffuser, mounting suitable for E14 / E27 / B22 lamp

holders, pf >= 0.5 (A) LED Lamps integral type, with PC

diffuser suitable LAMP holder (iii) 10 to 15 watts

Supplying and erecting LED indoor fittings with LEDs of

wattage 0.2 Watt to 0.5 Watt assembled on single MCPCB,

with housing used as a heat sink shall be made of thick

sheet Steel conforming to IS: 513/ CRCA/aluminium

pressure die cast powder coated and high U.V. & corrosion

resistance with diffuser housed in aluminium casted body

with company mark/name 160V to 270V,Power Factor

more than 0.9, THD < 15 %, CCT 3000 K to 6500K,

Luminaire efficacy> 85 lumens/watt , LED driver efficiency >

85 % (fitting required LM-79 & LM-80 Certificates)(NOTE:

Below description have shown ranges of Wattage capacity

of LED fittings.The Engineer incharge may select any

wattage capacity between the ranges shown.) (A) Square/

Circular shaped Surface/Recessed Mount Downlight with

provision for spring loaded mounting clips complete.IP20

(ii) 11-15 watts, Surge-2 KV - Cat III

152 (H) Mirror Light 9 Watts, wall mounted minimum 1 feet 8 Each 312.09

Supplying and erecting LED street light / Flood light fittings

with High power White LEDs wattage of 3 Watt and above

assembled on single MCPCB, efficiency more than

lm/w and corrosion free High pressure die cast aluminium

housing with smooth finish powder coated and heat sink

extruded aluminium with diffuser and Polycarbonate

optics/ lenses with company mark/name engraved or

embossed 160 to 270 V,Power Factor more than 0.95, THD

< 10 %, CCT 3000 K to 5700K,Uniformity ratio >0.45,

Luminaire efficacy> 100 lumens/watt . LED driver efficiency

> 85 %.( fittings required LM-79 & LM-80

certificates)(NOTE: Below description have shown ranges of

Wattage capacity of LED fittings.The Engineer incharge may

select any wattage capacity between the ranges shown.)

(A) Street Light (IP-65), Surge protection -4KV integral and

,Light must have 440VAC line supply with over-voltage

protection. (ii) 15 to 24 Watts

Providing & erecting Approved make Power Saving 50 Watt

Ceiling Fan with double ball bearing ISI mark with

Condenser 230 volt A.C. 50 Hz 1200 mm sweep complete

having 3blades with aluminium blades with , canopy &

cm. down rod erected with earthing.(Make shall be

approved by Engineer in charge)

155 Providing & erecting fresh air fan 250 mm dia with square 13 Each 1,559.44

frame make of ABS body with louvers - Cat. II

156 Supplying & erecting single phase approved make industrial 1 Each 3,339.06

exhaust fan suitable for medium duty ring mounted low

noise operation suitable for medium duty having following

dia size and maximum speed in RPM [D] 450 mm dia

Providing and erecting approved make split air-

conditioning unit consisting of copper condensing unit with

fan motor, hermetically sealed rotary compressor with

accessories etc. duly connected separately erected

evaporating unit and blower motor with its accessories by

means of extra supplied proper insulated copper

tubing,drain PVC pipes suitable for ( cost includes powder

coated Stand, Eco Friendly green gas charging, 15A plug top

& Remote Control) with necessary core cutting. (1) For

ISEER Range (KWH/KWH)(3.1 to 3.99) (b) for 1.5 ton

Supplying and erecting horizontal / vertical mounting type

storage water heater with copper container housed in

M.S./S.S./ABS body insulated with glass wool/puff

complete with heating elements,adjustable thermostats

300C to 850C, indicating lamp, safety valve, fusible plug,

etc.complete erected with coach bolts, nuts. washers &

cementation (A) 10 Ltr. with 3 KW. heating element Cat.III

159 providing and erecting Mains with 1.1 KV grade FRLS PVC 60 RM 200.99

insulated ISI marked stranded Copper conductor wire in

following type of pipe to be erected in / on wall / ceiling

with 2.5 sq. mm copper conductor FRLS PVC insulated

stranded wire of green colour for earth continuity of

following size (A) With medium class Rigid PVC pipe and

accessories (e) 3 wire 6 sq. mm

160 ditto as above but (f) 3 wire 10 sq. mm 100 RM 325.22

(use earth wire of 4 sq.mm )

161 ditto as above but 4 wire 10 sq. mm 60 RM 425.21

(use earth wire of 4 sq.mm )

162 Providing and erecting XLPE(IS:7098)(I)-88 ISI armoured 20 RM 183.82

cable multistrand Aluminium conductor for 1.1 KV. to be

laid on wall with necessary clamps or in existing trench /

pipe of following size of cables (A) 3 1/2 core 25 Sq. mm (

16 Sq. mm 1/2 core)

163 ditto as above but (D) 3 1/2 core 70 Sq. mm ( 35 Sq. mm 50 RM 378.75

164 Supplying and erecting insulated pair of soft copper tubing 100 RM 965.56

open or concealed including power and control

cable,necessary PVC drain pipes for Split AC machine up to

Supplying and fixing 55-inch Ultra HD LED Smart Television

with wall mounting bracket, including necessary power and

HDMI connectivity arrangements, complete in all respects.

The TV shall be of reputed make such as Samsung / LG /

Sony or equivalent approved, having minimum 4K Ultra HD

resolution, smart TV features, Wi-Fi connectivity, HDMI and

USB ports, supplied with original remote control and

Supply, installation, testing and commissioning of IP based

CCTV camera (Dome/Bullet type) having minimum 2MP /

4MP resolution, with IR night vision range up to 30 m,

minimum 1/2.8" CMOS sensor, H.265 video compression,

wide dynamic range (WDR), built-in IR LEDs, IP66

weatherproof housing (for outdoor cameras), complete

with mounting accessories, connectors, and required

fittings. Camera shall be of make Hikvision / Dahua / CP

Plus / Honeywell or equivalent approved.

Supply and installation of NVR suitable for minimum 8 /

channel IP cameras, supporting H.265 compression,

HDMI/VGA output, remote viewing capability, USB ports,

LAN connectivity and recording management software,

including all accessories complete. NVR shall be of make

Hikvision / Dahua / CP Plus or equivalent approved.

168 Supply and fixing of surveillance grade hard disk of 1 Each 15,150.00

minimum 4 TB / 6 TB capacity compatible with NVR for

continuous recording, suitable for 24×7 operation. Hard

disk shall be of make Seagate / Western Digital or

equivalent approved.

169 Supply and fixing of LED monitor (minimum 22"/24") with 1 Each 10,100.00

Full HD resolution for live viewing and playback of CCTV

cameras including HDMI cable and accessories. Monitor

shall be of make LG / Samsung / Dell or equivalent

170 Supply and laying of CAT-6 UTP cable for CCTV networking 300 Meter 35.35

including dressing, clamping and termination complete.

Cable shall be of make D-Link / Molex / Finolex / Havells or

equivalent approved.

Supply and installation of 8/16 port PoE network switch for

powering IP cameras and network connectivity including

adaptor and accessories complete. Switch shall be of make

TP-Link / Cisco / D-Link or equivalent approved.

172 Supply and installation of 12V DC power supply unit / SMPS 8 Each 4,545.00

for CCTV cameras including distribution box and wiring

complete. Power supply shall be of make CP Plus / Hikvision

/ Matrix or equivalent approved.

173 [1] GEAR LESS LIFT DRIVE (MRL) comprising of High 1 Each 9,72,076.52

Starting torque Lift 3 phase 440 V A. C. Permanent

Magnet Synchronous motor of proper rating with

high efficiency shall be used.[2] Micro processor

based / PLC, ACVVVF, vector control drive with

encoder feedback closed loop system shall be used

for lift car and door operation which shall be full

collective selective operation hall call demand

response, UP/DOWN hall stops, Main, Up/ Down

Contactor with overload and phase reversal relay and

safety controls.

[3] Car with M S platform with bracings of adequate

size and to sustain the impact load cabin + passenger

with safety factor of fire for steel and side panels of

Stainless steel of sheet of grade 304 duty. Car ceiling

will be S.S. finishes with aesthetic appearance with

LED ceiling lights. Car flooring shall be of s/s

chaker plate design sugeested of engineer in charge.

of engineer in charge. Car doors shall be of stainless

steel grade 304, hairline finish with centre opening /

telescopic automatic doors. Car panel will also be S.S.

304 finished with emergency stop device, mechanical

door safety device, facility of auto/ attended mode.

All car panel buttons and all floor switches must be

with brail language as per lift act.

[4] All landing doors must be fire rated for 2 hour

shall be fully automatic centre opening/ telescopic

opening made of hairline finish steel grade of

with key holes and infrared curtains with Unlocking

facility from outside

[5] Appropriate battery operated emergency light in

the car along with alarm switch shall be provided.

Also, Emergency Light & Fan should start immediately

without any Time Delay as soon as power fails.

[6] Digital scrolling indicator system for up-down

arrow along with floor position indicator shall be

provided inside the car and at all floors.

[7] Full height infra red curtain with multiple cross /

crossing light beams shall be provided.

[8] Automatic Rescue Device (ARD) shall be provided

accordingly of passenger capacity with Manual

Rescue Operation ( Manual Cranking Facility).

[9] Audio visual indication in the lift car showing over

loading shall be provided such that doors kept open

till excess load is removed.

[10] Spring buffers/PU Buffers shall be provided.

[11] Car fan as per passenger capacity with automatic

sleep timer shall be provided.

[12] Voice annunciator with suitable music shall be

provided in lift car.

[13] Self diagnostics system for operational and

safety parameters shall be provided in control panel.

[14] Mechanical over speed governor with governor

calibration as per actual site parameters and

submission of calibration certificate submission, door

key holes in the floor doors, fireman switch shall be

[15] Lift machine hoisting arrangement in the lift

machine room and monkey ladder for lift pit should

be provided by the lift agency, along with the other

steel structure works, foundations for the machine

[16] In the hoist way fascia plate shall be provided

without any extra cost, where ever required as / if

directed by engineer in charge.

[17] Permanent wiring with necessary safety devices

like RCCB in all circuit, Over Voltage Under Voltage

protection and THD eliminator in circuit for lift

machine room and lift well with proper numbers of

light points, with fixtures, exhaust fan and plug points

shall be provided by the agency. Only 3 phase Power

Supply shall be made available by department in lift

machine room. Necessary Earthing as per Lift

Act/Rules shall be arranged by Lift Agency.

[18] Any civil/ electrical works for additional and

alteration in lift shaft and machine room related to

erection of lift shall be made by lift agency without

any extra cost. (granite/marble fixing around all

landing door openings are not in lift agency’s scope.)

[19] Agency has to provide all working drawings and

documents and liaison services for obtaining all

necessary permission from lift inspector and other

authorities. [20] acrylic transparent

licence/display A4 size holder in lift car

[20A] As per statutory requirement of Govt. Of

Gujarat lift & escalator act 2000, lift agency has to

1. Car top safety barricade

2. Push & talk communication system.

3. Fireman's switch operation at Ground Floor.

4.carrying out third party lift inspection during/after

lift erection and provide report by third party

authorized by concern licensing authority 5.agency

has to provide third party insurance upto completion

of free maintenance period and submit the document

[21] Car Panel Operating Buttons with floor position

indicator/buttons must be of Auto Glow type clearly

visible when view from inside cabin.

[22] For Physically Handicapped person Full Length

Handrails of hairline finish steel grade of 304 should

be provided at appropriate height on the Rear & Side

Wall Panels in Lift Car. [23] With Necessary KVA

rating voltage controlled Stabilizer suitable for your

controller, drive and all equipments of lift.

[24] Necessary rating of DP Elcb and FP Elcb required

for lift is in scope of work which rating is sugested by

CEICED Department (electrical Inspector)

4/5/6 Passengers, Ground plus 1 upper floor with

Rated Speed of 1.0 m/sec,

(B) With General Specification attached herewith.

Supplying & erecting in earthpit of minimum bore dia.

225mm size approved make Safe Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 80 mm having 80-200

Micron galvanising, Inner pipe dia of 40 mm having

200-250 Micron galvanising, connection terminal dia

of 14 mm with constant ohmic value surrounded

by highly conductive compound with high charge

dissipation suitable for following type of applications

with chamber and heavy duty cover.(approved make

OEM has to submit test certificate including value of

earth resistane of installation.

[A] For electrical installation up to 440 V Length of

Back filling compound - 1 Nos. of Bag of 15 Kgs.

175 Supply, Installation, Testing & Commissioning of 1 Each 42,455.35

following size of Grid Tied Solar Power Plant with

Solar Panels (ALMM approved): Frame Material :

Anodized Aluminum alloy Frame With Twin Wall

Profile, Front Cover : High Transmission Low-Iron

Tempered Glass (AR Coated), High efficency and

positive power tolerance Pmax: 0/+5, Module

Efficiency should be approx. 19.5%-22%, Normal

operating temperature 45'C, Junction Box with

Waterproof IP67 & MC4 Compatible and Enclosed

with Bypass diodes, 100% Electroluminescence test

to ensure error free Modules, Thep. temp. co-

efficient of the PV module shall equal or better than -

0.45%/degree C. Solar PV modules of minimum fill

factor 75% to be used. Unit Production:- More than

4.5 Unit /kw /day (Actual)(1Year Avg) With 10 year

Product warranty and 25 year Linear Power Warranty

includes all mechanical and electrical parameters of

the Solar panel. Modules must be complied to the

DCR(Domestic content requirements). The Ration of

AC to DC is 5:6 for the Installation capacity which are

given in AC KW.

Solar Inverter: MPPT Range: MPPT Range: 80-1000 V

, Max efficiency: 97.5% - 98.9%, O/p Frequency:

50/60Hz, Operating Altitude (m) ≤4000, O/p Power

Factor: ~1, O/P THDi: <3%, Operating Tempreture

Range: -25~60°C, Integrated protection of Inverter

are Anti-islanding Protection, Input Reverse Polarity

Protection, Insulation Resistor Detection, Ground

Integrated, Input Reverse Polarity Protection

Integrated, Insulation Resistor Detection Integrated,

Residual Current Monitoring Unit Integrated, Output

Over Current Protection Integrated, Output Short

Circuit Protection Integrated, Output Over Voltage

Protection Integrated, Protection Degree: IP65, User

Interface LCD & APP,Datalogger & Communication:

GPRS / Wi-Fi, Module Mounting Structure: The

mounting (Rectangular pipe / square pipe / circular

pipe) with requisite cross bars, nuts and bolts, etc.

shall be Hot deep galvanized with minimum

80micron coating. The Rectangular / square /circular

hollow pipe section used for the structure should

have a minimum thickness of 2.0 mm. other than

above, the material thickness should be minimum

mm. A certificate of a structural engineer certifying

the strength and stability of the mounting structure

to withstand the weight and wind speed of

km/hour throughout the life span of 25 years of the

system, shall be submitted by the vendors. Hot

Dipped Galvanized steel coils. suitable arrangement

for base plate for foundation , solar panel mounting,

the structure should be suitable for carry the load of

solar panel,wiring, sprinkler system etc. with

necessary foundation work/wall mount, j bolt, anchor

fastner etc. the nut bolt used for installtion of

stucture should be (SS 304) quality.The ground

clearance of the bottom most edge of solar panel

shall not be less than 300 mm to 1200 mm or as per

(C ) Grid Tied Solar Power System: 11 - 25 kW (3 -

176 S.I.T.C of Poly Crystline/Mono Crystline PV Module 47 Per Watt 17,331.60

(ALMM approved) with 72 Cells - 150 Cells or More

Frame Material : Anodized Aluminum alloy Frame

With Twin Wall Profile, Front Cover : High

Transmission Low-Iron Tempered Glass (AR Coated),

High efficency and positive power tolerance Pmax:

0/+5, Module Efficiency should be approx. 18%-21%,

Normal operating temperature 45'C, Junction Box

with Waterproof IP67 & MC4 Compatible and

Enclosed with Bypass diodes 100%

Electroluminescence test to ensure error free

Modules, Thw temp. co-efficient of the PV module

shall equal or better than -0.45%/degree C. Solar PV

modules of minimum fill factor 75% to be used. Unit

Production:- 4 to 5 Unit /kw /day (Actual)(1Year Avg)

With 10 year Product warranty and 25 year Linear

Power Warranty.

(E) Moudule o/p Range: 520 - 545 watt, Maximum

Power Voltage Vmpp: 41 - 42 V, Maximum Power

Current Impp: 12.5 - 13 A

177 S.I.T.C of Solar Inverter Gried Tied: MPPT Range: 80- 25000 Per Watt 9.09

1000 V, Max efficiency: 97.5% - 98.9%, O/p

Frequency: 50/60Hz, Operating Altitude (m) ≤4000,

O/p Power Factor: ~1, O/P THDi: <3%, Operating

Tempreture Range: -25~60°C, Anti-islanding

Protection: Integrated, Input Reverse Polarity

Protection Integrated, Insulation Resistor Detection

Integrated, Residual Current Monitoring Unit

Integrated, Output Over Current Protection

Integrated, Output Short Circuit Protection

Integrated, Output Over Voltage Protection

Integrated, Protection Degree: IP65, User Interface

LCD & APP,Datalogger & Communication: GPRS / Wi-

(D) Solar Inverter: 15 kW to 25 kW: Max. input

Current: 27 A, Max DC i/p Power: 22100-32500W &

Nominal o/p Power: 15000-25000W, Nomimal O/p

Voltage: 400 V 3-Phase,Nominal O/p Current: 25-37A.

178 Supplying and Erecting Seamless Box Pipe of suitable 1500 Per kG 131.30

size for rooftop solar installations with good stability

agaist wind, Thickness 2 mm and 80 micron, Hot

Dipped Galvanized steel coils. suitable arrangement

for base plate for foundation , solar panel mounting,

the structure should be suitable for carry the load of

solar panel,wiring, sprinkler system etc. with

necessary foundation work/wall mount, j bolt, anchor

fastner etc. the nut bolt used for installtion of

stucture should be (SS 304) quality.

box. pipe ref. size (A) 40 x 40 x 2mm, (B) 50 × 50 ×

DC Cable: Electron beam cross linked compound,UV,

Ozone, Temperature & Hydrolysis resistant Flame

Retardant, Low Smoke Excellent Encapsulation

Very long / Service life >

Standards / Material Properties:

Fire performance : IEC 60332-1-2

Smoke emission : IEC 61034/ EN 50268-2

Halogen Free: EN 50267-2-1/-2, IEC 60754-2

Toxicity: EN 50305, ITC – Index <3

Ozone Resistant : EN50396

Weathering UV: HD 605/A1 or DIN

Approvals : EN 50618; H1Z2Z2-k

with suitable sized of PVC pipe(ISI Mark) and

Clamps,Shadels,Lugs.

178.1 (A) 1 core 4 sqmm copper DC cable Colour Red 250 RM 76.76

178.2 (B) 1 core 4 sqmm copper DC cable Colour Red 250 RM 76.76

180 S.I.T.C of Distribution board from AC Side ,ACDB 3- 1 Each 18,146.67

Phase - 21 kW - 50 kW: AC1 DUTY CONTRACTOR-80A

100A MCCB 4P(Cat III), 3 PHASE SPD, VOLTAGE

MONITORING RELAY,

ELR WITH CBCT, PHASE INDICATING LAMP, POWER

OTHER ACCESSORIES, All switchgears and connection

are enclosed with IP66 Enclosure and operate the

S.I.T.C of Distributiob System DC Side, DCDB - 20 kW -

25 kW (5in:5out) : Input Mcb - 1000 V, 16 Amp,

1000 V DC SPD TYPE 2, TERMINAL/END,PLATE/END

4SQMM (KUT6) FOR OUTPUT, DC CABLE With

suitable size of interconnection.

182 Supplying & Errecting MC4 Connector Male - Female 47 Each 52.52

Set for Solar DC Cable which is installed in Solar PV-

module/Inverter/DCDB etc.

183 Supplying and erecting, commissioning and testing of 1 Each 6,75,844.53

Diesel Generating set confirming to IS: 4722:1968 &

BS:5514 having continuous rating, 3 phase, 415 volts,

50 cycles A.C. supply comprising of a totally enclosed

air/water cooled diesel engine with multi-cylinders

developing suitable BHP not less than following

capacity at 1500 RPM with 10% overload for one

hour in 24 hours with standard accessories like fly

wheel, lubricating oil cooler, "A" class governor,

heavy duty fuel wheel and lubricating oil filter, oil

bath air filler, lubricating oil pressure gauge, end

exhaust manifold, standard set of tools with

adjustable spanners, screw drivers, cylinder head to

cover, joint cylinder head to exhaust, element lube oil

filter, 12 / 24 volts electric starting equipment

complete with standard heavy duty battery, dynamo,

cut-outs, ammeter, necessary wiring, pressure gauge,

starter etc and heavy duty Residential type exhaust

silencer (With DEF System) and vertical hot air duct

logged with asbestos rope, save oil trays, exhaust

piping of required length, standard wall/floor

mounted fuel with level indicator and piping and drip

proof alternator, self excited, self regulated, screen

protected, with excitation system, capable of

delivering the rated system output at 415 volts,

phase, 0.8 PF, 50 Hz, 4 wire, running at 1500 RPM,

conforming to IS-4722- 1968 with voltage regulation

+/- 5% of rated voltage from no load to full load. Both

the engine and alternator fitted on a common

fabricated steel base plate with antivibration

mounting engine and alternator both connected to

each other by flexible flange coupling and with

floor/wall mounted control panel box comprising of

voltmeter ammeter, selector switches, ACB / MCCB

/ MCB of adequate capacity,

indicator lamps duly wired with HRC fuses. The

alternator & control panel shall be connected with

provided suitable capacity armoured cable and

complete with Acoustic enclosure (canopy) made out

of 16 SWG CRCA Sheet, sound absorbing material

Rockwool of 64 density & 100 mm thick conforming

to IS:8183 / PU Foam of 40 Density - at least 40 mm.

The resin bonded rockwool covered from inside the

canopy by perforated sheet with 3/4 mm holes,

sound level not more than 75 dB at a distance of

mtr, as per PVCT norms.DG set should have in built

fuel tank capacity of minimum 8 hrs of continous

running capacity on full load . Erection,

commissioning and satisfactory testing as per

requirement with first filling of fuel (minimum up to

the 80% of fuel tank capacity), oil, etc. with

guarantee / Warrantee of complete system for Two

years. & with obtaining all necessary certificate from

Electrical Inspector. The Capacity and Ratings of DG

sets are as below. (As per new CPCB4+ Emission

norms Engine With - Turbo Charger, EGR (Exhaust

Gas Recirculation), CRS (Common Rail Fuel System),

DOC (Diesel Oxidation Catalyst), SCR (Selective

Catalytic Reduction), Integrated wiring harness

connected to ECU .)

(I) Continuous Rating of 62.5 KVA ,BHP not less than

184 Providing & erecting approved make AMF control 1 Each 97,320.57

panel suitable for following size of 3 phase, 415 V.,

50 cycles, A.C. diesel generating set complete of

scope as detailed below:

1) Power module: A pair of electromechanically

interlocked contactors (for mains & generator)

Overload relay for generator contactor Neutral

contactor for mains and generator Power socket for

2) Control and metering module: Line voltage

monitor. Generator voltage monitor Ammeter

items attempt start facility. Air circuit

breakers/MCB/MCCB of suitable rating for

auto/manual operation. Auto/manual switch.

Emergency stop push buttons. Manual start push

button. frequency meter. Engine hour meter. Two

earthing studs.

3) Protection module: The engine shutdown in the

unlikely event of Low lube oil pressure High cylinder

head temperature. V belt failure.

4) Indicators with alarm Load on generator.

5) Indicators Load on mains Engine fails to start .

Emergency stop battery charger.

The AMF Panel of following capacity

(A) AMF Control Panel for 50/62.5 KVA 3 phase DG

185 Providing & erecting approved make ATS panel 1 Each 57,347.80

suitable for following size of 3 phase, 415 V.,

cycles, A.C. diesel generating set complete of scope

as detailed below:

1) Power module: Motorised Changeover switch

with ATS controller, Auxiliary contactor with NO & NC

contacts with Automatic Battery Charger, indicating

lamps for Generator ON, Mains ON, Load and suitable

control terminals and power terminals with neutral

earthing studs.

(C) ATS Panel for 50 / 62.5 KVA 3 phase DG Set

Supplying & erecting in earthpit of minimum bore dia.

225mm size approved make Safe Earthing Electrode

consisting Pipe-in-Pipe Technology as per IS 3043-

1987 made of corrosion free hot dipped G.I.Pipes

having Outer pipe dia of 80 mm having 80-200

Micron galvanising, Inner pipe dia of 40 mm having

200-250 Micron galvanising, connection terminal dia

of 14 mm with constant ohmic value surrounded

by highly conductive compound with high charge

dissipation suitable for following type of applications

with chamber and heavy duty cover.(approved make

OEM has to submit test certificate including value of

earth resistane of installation.

[A] For electrical installation up to 440 V Length of

Back filling compound - 1 Nos. of Bag of 15 Kgs.

Providing & erecting, programming, testing of

chairman unit microphone with flexible stem of

mm in length and light ring built in loud speaker ,two

head phone socket ,attractive design ,priority button

for chairman microphone,built in volume control for

head phones,chime tone facility to precede chairman

priority calls,microphone on/off button,red indicates

for microphone is active,frequency response -400Hz

to 10kHz,nominal acoustic input -85 dB SPL

[[Approved by Competent Authority i.e. not Below

the rank of Executive Engineer ]

188 Providing & erecting, programming, testing of 19 Each 5,565.10

Delegate unit microphone with flexible stem of

mm in length and light ring built in loud speaker ,two

head phone socket ,attractive design ,built in volume

control for head phones,chime tone facility to

precede chairman priority calls,microphone on/off

button,red indicates for microphone is

active,frequency response -400Hz to 10kHz,nominal

acoustic input -85 dB SPL [[Approved by Competent

Authority i.e. not Below the rank of Executive

Supplying & erecting dual channel amplifier ,power

handling capacity of 180 watt ,four micro phone

inputs with independent level control ,built in FM

tuner,with preset memories,USB drive & SD card for

MP3 playback ,100v /telephone input with priority

and VOX,frequency response-80 Hz to 18k Hz Philips

/ /distortion less than 1% @ rated power up to

units [[Approved by Competent Authority i.e. not

Below the rank of Executive Engineer ]

190 Supplying and erecting ceiling speaker with rated 4 Each 2,569.44

power of 30 watt/power tapping 30/15/7.5 watt

available,opening angle 180 degree H * 77 degree V

,sound pressure level 88 dB ,frequency response of

70Hz to 20KHz [[Approved by Competent Authority

i.e. not Below the rank of Executive Engineer ]

SITC of 3LCD Lamp based projector having wxga

(1280x800) or better resolution with minimum white

brightness of 3800 lumens and color brightness of

3800 lumens. The projector should have minimum

1HDMI,1VGA input. Having contrast ratio of 15000:1

or more. the projector should have auto vertical key

stone correction of +/- 30 degree and Manual

Horizontal of +/-30 degree. the projector should have

optical lens, throw ratio 1.30-1.56:1. Zoom Factor of

1.2. Lens focus Manual having focal length 16.9mm to

20.28mm. projector should have features like AV

mute slide, quick corner and split function and should

support wireless functionality with inbuilt wifi or wifi

dongle. [Approved by Competent Authority i.e. not

Below the rank of Executive Engineer ]

192 SITC of universal Projector mounting kit, with 1 Each 6,848.81

necessary grouting, fasteners etc. with adjustable

height and suitable for all types of projectors.

[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

193 SITC of 120 inch Self Lock MW (8 x 6) Instalock Slow 1 Each 5,334.82

Retraction Screen, Aspect Ratio-4:3 [Approved by

Competent Authority i.e. not Below the rank of

Executive Engineer ]

194 SITC of O. F.Cable 06F Outdoor - Armoured Unitube 20 Each 50.50

SM - HDPE Sheath [Approved by Competent

Authority i.e. not Below the rank of Executive

195 SITC of LIU 12 PORT Rack Mount - Loaded (LC) SM 1 Each 6,901.33

[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

196 SITC of PIGTAIL LC SM SIMPLEX LENGTH- 1m 20 Each 779.72

[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

197 SITC of PATCH CORD LC-LC SM DUPLEX LENGTH- 3m 20 Each 1,901.83

[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

198 SITC of CAT6 UTP 23AWG Solid: Per Meter [Approved 20 Each 43.43

by Competent Authority i.e. not Below the rank of

Executive Engineer ]

199 SITC of Face Plate - Single (Keystone Jack,square) 10 Each 90.90

[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

200 SITC of Face Plate - Dual (Keystone Jack,square) 10 Each 101.00

[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

201 SITC of Jack Cat 6 Keystone UTP [Approved by 20 Each 161.60

Competent Authority i.e. not Below the rank of

Executive Engineer ]

202 SITC of Patch Panel UTP Keystone- 24 Port- Unloaded 1 Each 1,499.85

(Cat 5e,Cat 6 & Cat 6 A ) [Approved by Competent

Authority i.e. not Below the rank of Executive

SITC of Patch Panel Cat 6 UTP Keystone Type- 24 Port-

Fully Loaded [Approved by Competent Authority i.e.

not Below the rank of Executive Engineer ]

204 SITC of CAT6 UTP 24AWG PATCH CORD:1M,Plug 30U' 20 Each 156.55

[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

205 SITC of CAT6 UTP 24AWG PATCH CORD:2M,Plug 30U' 20 Each 200.99

[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

SITC of 8 x 10/100/1000BASE-T PoE ports 2 x Gigabit

Advanced L2 switching and security features L2+

Static Routing Optional “standard mode” or

“surveillance mode” management user interface 65W

PoE budget [Approved by Competent Authority i.e.

not Below the rank of Executive Engineer ]

207 SITC of 24 x 10/100/1000BASE-T ports 4 x Gigabit 1 Each 15,399.47

RJ45/SFP Combo ports

Advanced L2 switching and security features L2+

Static Routing Optional “standard mode” or

“surveillance mode” management user interface

[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

208 SITC of 24 x 10/100/1000BASE-T PoE ports 4 x Gigabit 1 Each 31,996.80

RJ45/SFP Combo ports Advanced L2 switching and

security features L2+ Static Routing

Optional “standard mode” or “surveillance mode”

management user interface 193 W PoE budget

[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

209 SITC of 48 x 10/100/1000BASE-T ports 4 x Gigabit 1 Each 30,398.98

GbE/SFP combo ports

Advanced L2 switching and security features L2+

Optional “standard mode” or “surveillance mode”

management user interface

[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

210 SITC of Maximum distance of up to 10 km Hot- 2 Each 4,801.54

pluggable Single-mode fiber 1000BASE-LX (IEEE

802.3z standard) Duplex LC connector MSA, RoHS-

compliant [Approved by Competent Authority i.e. not

Below the rank of Executive Engineer ]

211 Supply, Installation Testing & Commissioning 5 Mtr. 2 Each 828.20

HDMI Interface Cable as per the detailed

Specifications supports transmission of 4K Signals as

per the detailed Specifications

212 Supply, Installation Testing & Commissioning 10 Mtr. 2 Each 1,323.10

HDMI Interface Cable as per the detailed

Specifications supports transmission of 4K Signals as

per the detailed Specifications

213 Supply, Installation Testing & Commissioning 15 Mtr. 2 Each 1,777.60

HDMI Interface Cable as per the detailed

Specifications supports transmission of 4K Signals as

per the detailed Specifications

214 Supply, Installation, Testing and Comissioning of USB 1 Each 16,688.23

Full HD 1080p @ 30fps Webcamera, 1/3 " 2mp

Sensor, 90 degree Wide FOV, built in Mic, MJPEG

compression format, Manual Focus, Auto white

balance & other image processing algorithms, USB

2.0, BIS, CE,FCC, RoHS certified.

[Approved by Competent Authority i.e. not Below the

rank of Executive Engineer ]

215 Supply, installation, testing and commissioning of FM 1 Each 62,493.75

approved or UL listed microprocessor- based single

loop, true peer-to-peer networkable, addressable Fire

Alarm Control Panel (FACP) with its own

microcontroller memory, communication module,

fire device loop interface cards for intelligent

initiating and indicating devices and peer-to-peer

networkable with other addressable fire alarm

panels. conforming to UL 2572 mass notification

systems & NFPA 72, complete with accessories all as

specified and directed by engineer-in-charge. (one for

216 Supply, installation, testing and commissioning of FM 1 Each 3,471.88

approved or UL listed addressable control module to

provide FACP a circuit for notification appliances (e.g.

Horns, Strobes, Horn Strobes, etc.) having built-in

type identification, integral LED indicators, high noise

immunity, SMES screws with clamping plates for

wiring ease, direct-dial entry of address, etc.

complete with accessories as specified and directed

by engineer-in-charge.

217 Supply, installation, testing and commissioning of FM 2 Each 3,055.25

approved or UL listed surface / semi- flush mounted

Dual Action Manual Pull Station "Push In & Pull

Down" including an addressable interface for the

intelligent FACP having built-in bicolour LED which is

visible, flashing in normal operation and latching

steady red in alarm condition, captive screw

terminals wire-ready for easy connection to SLC loop

complete all as specified and directed by engineer-in-

218 Supply, installation, testing and commissioning of UL 2 Each 6,249.38

listed of Horn Strobe, wired as a primary notification

appliance, flashing 75 cd at 1 Hz over the strobe's

entire operating voltage range, xenon flash tube and

associated lens / reflector system, built-in

synchronization feature keeping strobes in sync for

up to 30 minutes, horn producing audible

annunciation of 75 dBA at 3 m distance complete all

as specified and directed by engineer-in-charge.

219 Supply, installation, testing and commissioning of FM 1 Each 48,606.25

approved or UL listed remote power supply

conforming to UL 864 & 1481 and NFPA 72 with

integral battery charger capable of charging up to

Ah batteries to provide regulated and filtered 24 VDC

power to notification appliance circuits, having power-

supervision relay, fully regulated and filtered power

output, AC trouble report selectable for immediate 2-

hour delay, selectable earth fault detection, etc.

complete all as specified and directed by engineer-in-

220 M & L for low smoke zero halogen (LS0H) flame 30 Rm 111.10

retardant fire alarm cable, conforming to BS 7629-1,

BS 6387 & BS EN 50200 and rated for 500 V, having

plain annealed stranded copper conductor with

primary insulation of glass mica fire resistant tape

and secondary insulation of high performance

silicone rubber, earth/drain wire of annealed tinned

copper, electrostatic screen of aluminium fire barrier

and type LTS3 outer sheath conforming to BS

suitable for operating temperature range -30 ˚C to

+70 ˚C and minimum bending radius being 6 times

the overall cable diameter, RED in colour, including

laying, termination and ferruling complete all as

specified and directed by engineer-in-charge. 2 core,

221 Supply, installation, testing and commissioning of 1 Each 66,660.00

electric driven Booster Pump at the terrace tank level

to deliver 900 LPM flowrate at 30 MWC head and

suitable for automatic operation and consisting of

following, complete with accessories as specified and

directed by engineer-in-charge.

222 M & L for ISI marked MS ERW pipes conforming to IS: 20 RM 486.06

1239 (Part 1 & 2) with all accessories like all fittings

including tees, elbows, reducers, union, flanges,

rubber gaskets, GI nuts bolts, washer, including

supporting/fixing the pipe on floor / wall / ceiling

with clamps, hangers, angles, channels (using anchor

fasteners) with painting of one coat primer and 2 or

more coats of synthetic enamel paint complete as

specified and directed by the engineer-in-charge.

223 S & F PN 1.6 rated CI 100 mm NB sluice valve, 1 Each 9,026.88

conforming to IS 14846: 2000, having CI body, wedge,

bonnet, stuffing box, gland, handwheel, thrust plate,

GM body ring, wedge ring, wedge nut, CS bolts &

nuts, SS stem, flange drilling standard end connection

conforming to IS 1538: 1993, etc. along with

necessary accessories complete all as specified and

directed by the engineer-in-charge.

M & L for PN 1.6 rated 100 mm NB Cast iron (CI) non

return valve, conforming to IS 14846: 2000 with cast

iron body & bonnet, SS spindle & stem conforming to

IS 6603: 2001, cast iron stuffing box, carbon steel

stud / bolt / nut & washer, Hand wheel operated and

flange end connection conforming to IS 1538:

with necessary accessories complete all as specified

and directed by the engineer-in-charge.

S & F of PN 1.6 rated 25 mm NB full bore, two piece

design, quarter turn, lever operated brass ball valve

having nickel-plated forged brass body & end

connector, brass chrome plated ball, PTFE body seat

ring & packing, H.T. brass stem, nut & gland, rubber

'O' ring, powder coated MS lever and screwed female

ends, etc. with accessories complete as specified and

directed by the engineer-in-charge.

226 S & F indoor type lockable wall-mounted hose 2 Each 3,888.50

cabinet made of 18 gauge MS sheet of size 800 mm X

600 mm X 250 mm having double door with 3 mm

thick glass and door frame made of 16 gauge MS

sheet painted two coats of fire red outside and

brilliant white inside over a coat of primer suitable to

house two sets of hose RRL hose (15 m length) and

gunmetal branch pipe complete as specified and

directed by the engineer-in-charge.

S & F gunmetal fire hydrant single landing valve with

80 mm NB flanged inlet, brass spindle controlled

mm NB female instantaneous outlet type gunmetal

coupling, blank cap, chain, twist release type lug & all

accessories conforming to IS 5290: 1993 including

fixing and flanged tapping complete as specified and

directed by the engineer-in-charge.

228 S & F non-percolating rubber reinforced lined RRL 4 Each 5,832.75

hose type- A 15 m long fire hose of 63 mm NB size,

conforming to IS 636: 1988, rated for bursting

pressure of 35.7 kg/cm² complete with gunmetal

male & female coupling conforming to IS: 903-

bound and rivetted to the hose pipe with copper

rivets and 1.5 mm² copper wire complete as specified

and directed by the engineer-in-charge.

S & F branch pipe, conforming to IS 903: 1993, having

63 mm NB instantaneous gunmetal inlet, made

threaded outlet, 15 mm NB long nozzle, suitable for

inter connection to hose pipe coupling complete as

specified and directed by the engineer-in-charge.

230 S & F swinging type 36 m long First Aid Hose Reel, 2 Each 9,026.88

conforming to IS:884-1969, having 19 mm NB

thermoplastic reinforced hose reel tubing,

conforming to IS: 12585- 1988, 25 mm NB ball valve,

stop cock, terminating with gunmetal coupling &

nozzle of 6 mm NB outlet with shut-off valve,

conforming to IS: 8090- 1976 complete with MS

socket for tap-off, red colour drum, brackets

(including painting) for fixing on wall with anchor

fastener, bolts, nuts, etc. complete as specified and

directed by the engineer-in-charge.

231 Supplying, installing ,testing and commissioning of 1 Each 25,691.88

MS air cushion tank on top of each riser, conforming

to IS: 4736-1968, fabricated from 6 mm thick MS

plate, 200 mm in diameter and 1.2 m in height with

dished ends fabricated from 8 mm thick MS plate

having flanged inlet connection and drain

arrangement with 25 mm NB valve, pressure gauge &

gun metal stop cock complete as specified and

directed by the engineer-in-charge.

232 Supply, installation, testing and commissioning of 4- 1 Each 10,415.63

way fire brigade inlet connection, conforming to IS:

5290- 1993, with four 63 mm NB inbuilt gunmetal

non-return valves, four 63 mm NB instantaneous

couplings arranged on 150 mm NB pipe manifold and

connected to fire hydrant ring main and fire hydrant

wet riser pipe complete as specified and directed by

the engineer-in-charge.

233 Providing and erecting ISI mark Medium class RIGID 50 RM 33.33

PVC PIPES of following size complete to be erected

on/in wall or ceiling erected with necessary PVC

fittings & Junction boxes fixed with adhesive solution

& Clamps with following dia of pipes, in approved

manner as directed (b) 25 mm

234 Supplying and erecting push button operated fully Each 1.00 9,758.62

automatic Star-Delta starter with 3 Nos. of 15A.rating

contactors and directly operated thermal overload

relay having 10-21A range and erected in sheet

steel enclosure for 3 phase 415V. 50 c/s. A.C. motors

from 7.5 to 15H.P. complete erected on

235 Providing and erecting XLPE (IS:7098)(I)-88 ISI 30 Mtr. 140.39

armoured cable multistrand Aluminium conductor for

1.1 KV. to be laid on wall with necessary clamps or in

existing trench / pipe of following size of cables (C)

236 Supplying & erecting carbon dioxide (CO2) fire 10 Each 8,671.86

extinguisher user of following capacity with necessary

clamps made from 50 x 6 mm M.S. Flat with nut &

bolts grouted in wall complete. [B] For 5.5 / 6.5 KG

237 Supplying & erecting ABC powder type 'Ceasefire' 10 Each 848.40

type Fire extinguisher as per IS 13849 or 1 Kg capacity

with necessary clamp for erection on wall

I/We am/are willing to carry out the work at………………….% above/below percent(Should be written in figures and

words) of the estimated rate mentioned above. Amount of my /our

Tender works out as under.

Estimated amount put to tender Estimated amount put to tender

Deduct………% below Add………% Above

In words In words

1 The Contractor shall exhibit a board with detailed specification and details of work as directed by the

2 The labour cess will be deducted as per prevailing rules i.e. 1% of the work done.

3 GST and Income tax TDS will be deducted at a source while making payments of bills

4 In all R.C.C. Items in Rate Analysis Standard Cement Consumption has been taken as per Govt. G.R.:

PRC-10/2017 Cement Consumption/16/C Date:11/05/2017 as stated in S.O.R. therefore in R.C.C.

items where there is a change as per actual mix design the cost of difference of cement consumption

have been deducted from the rate of original item at the rate of input rate mentioned in all the tender.

Dy. Executive Engineer Divisional Accountant

Irri. Project. Sub-Dn. No.17 Medium Irrigation Project Division

Ankleshwar Ankleshwar

Executive Engineer

Medium Irrigation Project Division