Construction of Regional Passport Office (RPO) Building at Rajbagh, Srinagar, Jammu and Kashmir

Item of Work DSR-2023 DSR-2025 NS/MR Items TOTAL

Total DRIVER FACE AND AUTOMATIC NUMBER PLATE

8 RECORDING SYSTEM/ RECOGNITION SYSTEM, BAGGAE ₹ 0.00 ₹ 0.00 ₹ 40,60,000.00 ₹ 40,60,000.00

SCANNER, Boom Barrier (H )=

9 Total EPABX System(Avaya/NEC/Alcatel) (I )= ₹ 0.00 ₹ 0.00 ₹ 18,38,846.00 ₹ 18,38,846.00

12 Total Solar Photovoltaic Power Plant (L)= ₹ 0.00 ₹ 32,56,800.00 ₹ 0.00 ₹ 32,56,800.00

16 ELECTRICAL VEHICLE CHARGER ₹ 0.00 ₹ 57,08,195.00 ₹ 0.00 ₹ 57,08,195.00

Multiplication factor for modified Analysis of Rate @0.973 on DSR 2023 Items ₹ 23,96,82,098.25 ₹ 5,75,95,645.00 ₹ 7,90,95,329.67 ₹ 37,63,73,072.92

Grand Total (DSR+NDSR) Rs. 38,65,36,313.00

Grand Total (DSR+NDSR) Rs. 38,65,36,313.00

Digitally signed by DIWAKAR

BOQ for Construction of New Passport Office & Residentail Quarters at Rajbagh, Srinagar.

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

A Civil Works (Buildings)

1.1.1 Disposal of Excavated material by mechanical transport upto permissible limits, including loading , unloading.(upto lead of 10Km).

2.6 Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means over areas (exceeding 30 cm in depth, 1.5 m in

width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by

2 Engineer-in-charge.

2.8 Earth work in excavation by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding

1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated

3 soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

2.25 Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth,

consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift.

5 2.27 Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete Cum 300.00 2123.75 637125.00 637125.00

4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to

plinth level : 0.00

4.1.3 1:2:4 (1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 20 mm nominal size derived from

natural sources)

4.1.8 1:4:8(1 Cement : 4 coarse sand (zone-III) derived from natural sources : 8 graded stone aggregate 40 mm nominal size derived from

natural sources)

4.1.5 1:3:6 (1 Cement : 3 coarse sand (zone-III) derived from natural sources : 6 graded stone aggregate 20 mm nominal size derived from

natural sources)

4.17 Making plinth protection 50 mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone-III) derived from natural sources : 6

graded stone aggregate 20 mm nominal size derived from natural sources) over 75 mm thick bed of dry brick ballast 40 mm nominal

size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the

5.9 Centring and shuttering including strutting, propping etc and removal of form work:- 0.00

5.9.1 Foundations, footings, bases of columns, etc. for mass

5.9.2 Wall, (any thickness) including attached pilasters, buttresses, plinth and string coarses etc Sqm 1488.00 842.50 1253640.00 1253640.00

8 5.9.3 Suspended floors, roofs, landings, balconies and access platform Sqm 1617.72 927.25 1500030.87 1500030.87

5.9.5 Lintels, beams, plinth beams, girders, bressumers and cantilevers Sqm 3874.47 736.40 2853159.71 2853159.71

5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts Sqm 3235.96 961.30 3110728.35 3110728.35

5.9.16.1 Edges of slabs and breaks in floors and walls

Under 20 cm wide

5.22.6 Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete.Thermo-

Mechanically Treated bars of grade Fe-500D or more

5.33 Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using

coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement,

admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and

workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding

the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of

concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case 0.00

10 the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to

either re-design the mix or bear the cost of extra cement. Concrete of M30 grade with minimum cement

content of 350 kg /cum

5.33.1.2 All works upto plinth level Cum 1558.60 9655.70 15049374.02 15049374.02

5.33.2.2 All works above plinth level upto floor V level Cum 1656.82 10011.35 16587050.56 16587050.56

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

6.4 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to

11 floor V level in all shapes and sizes in : Cum 1707.23 9105.95 15545951.02 15545951.02

6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand)

6.13 Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level

6.13.2 Cement mortar 1:4 (1 cement :4 coarse sand)

8.2 Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms,

vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick

base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups,

13 including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels. Sqm 21.54 5136.30 110635.90 110635.90

8.2.2 Granite stone slab of colour black,Cherry/Ruby red

8.2.2.2 Area of slab over 0.50 sqm

8.3 Providing edge moulding to 18 mm thick marble stone counters, Vanities etc., including machine polishing to edge to give high gloss

14 finish etc. complete as per design approved by Engineer-in-Charge. Rm 794.31 298.60 237180.97 237180.97

8.3.1 Marble work

Designing, fabricating, testing, installing and fixing in position Curtain Wall with Aluminium Composite Panel Cladding, with open

grooves for linear as well as curvilinear portions of the building , for all heights and all levels etc. including:

(a) Structural analysis & design and preparation of shop drawings for pressure equalisation or rain screen principle as required,

proper drainage of water to make it watertight including checking of all the structural and functional design.

(b) Providing, fabricating and supplying and fixing panels of aluminium composite panel cladding in pan shape in metalic colour of

approved shades made out of 4 mm thick aluminium composite panel material consisting of 3 mm thick FR grade mineral core

sandwiched between two Aluminium sheets (each 0.5 mm thick). The aluminium composite panel cladding sheet shall be coil coated,

with Kynar 500 based PVDF / Lumiflon based fluoropolymer resin coating of approved colour and shade on face # 1 and polymer

(Service) coating on face # 2 as specified using

stainless steel screws, nuts, bolts, washers, cleats, weather silicone sealant, backer rods etc.

15 8.32 (c) The fastening brackets of Aluminium alloy 6005 T5 / MS with Hot Dip Galvanised with serrations and serrated washers to arrest

the wind load movement, fasteners, SS 316 Pins and anchor bolts of approved make in SS 316, Nylon separators to prevent bi-

metallic contacts all complete required to perform as per specification and drawing The item includes cost of all material & labour

component, the cost of all mockups at site, cost of all samples of the individual components for testing in an approved laboratory,

field tests on the assembled working curtain wall with aluminium composite panel cladding, cleaning and protection of the curtain

wall with aluminium composite panel cladding till the handing over of the building for occupation. Base frame work for ACP cladding sqm 540.60 5015.05 2711136.03 2711136.03

is payable under the relevant aluminium items. The Contractor shall provide curtain wall with aluminium composite panel cladding,

having all the performance characteristics all complete , as per the Architecturaldrawings, as per item description, as specified, as per

the approved shop drawings and as directed by the Engineer-in-Charge. However, for the purpose of payment, only the actual area

on the external face of the curtain wall with Aluminum Composite Panel Cladding (including width of groove) shall be measured in

sqm. up to two decimal places.

9.1 Providing wood work in frames of doors, windows, clerestory windows and other frames, wrought framed and fixed in position with

16 hold fast lugs or with dash fasteners of required dia & length (hold fast lugs or dash fastener shall be paid for separately). 0.00

9.5 Providing and fixing panelled or panelled and glazed shutters for doors, windows and clerestory windows, fixing with butt hinges of

required size with necessary screws, excluding panelling which will be paid for separately, all complete as per direction of Engineer-in-

charge.(Note: Butt hinges and necessary screws shall be paid separately)

Second class teak wood

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

9.120 Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size

of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make

and manufacture. M.S.

frame covered with 5 mm thick heat moulded PVC ‘C’ channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be

flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which

75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC

sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be

provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail &

bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm

(5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional

5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the ‘C’ Channel using PVC solvent adhesive etc. complete

as per direction of Engineer-in-charge, manufacturer’s specification & drawing.

9.120.2 30 mm thick pre laminated PVC door shutters

9.173 Providing and fixing ready made 304 grade stainless steel Modular kitchen basket and accessories such as right angle basket (Plain

Cup & Saucer, plant, Partition, Bottle rack, Thali, Cutlery) kitchen utensil basket, Dinner set basket, kitchen grain basket,

Multipurpose basket as per site requirement including finishing (wherever required) and fittings. The same shall be fixed with

necessary stainless steel nuts & bolts, Stainless Steel screws & telescopic channel etc. as per direction of Engineer-incharge. (For

payment purpose only weight of Stainless steel basket shall be considered excluding weight of all fixing accessories such as nuts,

bolts, fasteners telescopic basket channels etc. Payment of providing and fixing telescopic channel shall be paid separately)

9.53 Providing 40x5 mm flat iron hold fast 400 mm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and

21 embedding in cement concrete block 300x100x150 mm 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm No. 810.00 228.85 185368.50 185368.50

9.74 Providing and fixing bright finished brass tower bolts (barrel type) with necessary screws etc. complete : 0.00 0.00

9.76 Providing and fixing bright finished brass 100 mm mortice latch and lock with 6 levers and a pair of lever handles of approved quality

with necessary screws etc. complete.

9.83 Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564,

24 embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete. No. 138.00 1124.85 155229.30 155229.30

9.90 Providing and fixing special quality chromium plated brass cupboard locks with six levers of approved quality including necessary

9.90.1 Size 40 mm

9.101 Providing and fixing aluminum hanging floor door stopper, ISI marked, anodized (anodic coating not less than grade AC 10 as per IS

26 : 1868) transparent or dyed to required colour or shade with necessary screws etc. complete : No. 194.00 72.35 14035.90 14035.90

9.103.2 Twin rubber stopper

9.117 Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below

(tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and

stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of

size 19 X 19 mm and 1 mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per

manufacturer’s specification and direction of Engineerin- charge, 9.117.2 Extruded section profile size

9.147 Providing and fixing factory made uPVC glazed/wire mesh windows/ doors comprising of lead free uPVC multi-chambered frame,

sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2

profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with

galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks

and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of

minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as

per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if

required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing

hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather

proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD

specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per

design approved by Engineer-in-Charge.

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

9.147.A1.3 9.147.A1 Two track two panels sliding window with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body.

Using R4 series with frame (64 mm & above) x (45 mm & above) & sash (44 mm & above) x (55 mm & above) with zinc alloy Sqm 60.00 9628.60 577716.00 577716.00

(zamak) powder coated handle on every panel along with multi-point locking system (Height above 1.8m).

9.147.E5.3 9.147.E5 Casement cum fixed panel window having single casement panel at both ends & middle fixed panel with S.S 304 friction

hinges as per size and weight of sash, multi-point locking system, zinc alloy (zamak) powder coated handles. Using R4 series with

frame (64 mm & above ) x (50 mm & above) & sash (64 mm & above) x (70 mm & above) & mullion (64 mm & above) x (70 mm &

above). (Height above 1.8 metre; each openable shutter upto 0.8m width)

9.147.D1.1 Ventilator Casement window single panel with or without fixed panel with S.S. 304 friction hinges as per size and weight of sash,

single point locking zinc alloy (zamak) powder coated handles.Using R1 series with frame (33 mm & above ) x (35 mm & above) & Sqm 38.13 13201.20 503361.76 503361.76

sash /mullion (33 mm & above) x (50 mm & above). (Height upto 0.90 metre).

9.149 Providing and fixing casement handle made of zinc alloyed (white powder coated) for UPVC casement window with necessary

screws etc. complete

9.150 Providing and fixing zinc alloyed (white powder coated) touch lock for UPVC sliding window with necessary screws etc. complete

31 9.151 Providing and fixing steel roller for UPVC sliding window with necessary screws etc. complete. No 536.00 115.80 62068.80 62068.80

9.165.2 Providing and fixing bright /matt finished Stainless Steel handles of approved quality & make with necessary screws etc all complete.

9.166 Providing and fixing 18 mm thick both sides Pre-laminated cement bonded wood particle board as per IS : 15786:2008 of approved

brand and shade with suitable full threaded steel screws etc. in partitions, boxes, shelves, racks and cupboard, kitchen cabinet under

kitchen counter etc. all complete as per direction of Engineer-in-charge (Note: Fittings to be paid separately).

9.166.1 18 mm thick

9.168 Providing and fixing cupboard shutter with 19 mm thick one side decorative and other side balancing lamination factory pressed BWP

rade marine ply as per IS 710 of approved brand including 2 mm thick PVC edge banding tape with hot glue by edge bending

34 machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer-in-charge. (Payment sqm 141.80 2829.25 401187.65 401187.65

of providing and fixing auto

closing hinges shall be paid separately)

9.170 Providing and fixing stainless steel fancy handle of approved make fixed with SS screws etc. complete as per direction of Engineer-in-

9.171 Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard

36 shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of No 308.00 272.00 83776.00 83776.00

Engineer-in-charge.

10.16 Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in

position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc.

10.16.1 Hot finished welded type tubes

10.30 Providing & fixing glass panes with putty and glazing clips in steel doors, windows, clerestory windows, all complete with : 0.00 0.00

10.28 Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding,

buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts

complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size,

on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment

purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

10.29.2 Providing & fixing fly proof wire gauze to windows, clerestory windows & doors with M.S. Flat 15x3 mm and nuts & bolts

complete.Stainless steel (grade 304) wire gauze of 0.5 mm dia wireand 1.4 mm aperture on both sides

11.26 Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match

the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :

11.26.1 25 mm thick

11.33 25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with

11.33.1 Second class teak wood

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

11.52 Providing and laying machine cut, mirror polished Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in

patterns in combination with Italian marble stones of different colours, shades and finished surface texture etc., in linear portions of

the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of

43 cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including pointing with white Sqm 1740.00 6927.35 12053589.00 12053589.00

cement slurry admixed with pigment to match the marble shade, including rubbing, curing and polishing etc. all complete as specified

and as directed by the Engineer-in-Charge.

11.52.1 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

11.41A Providing and laying Vitrified tiles in floor in different sizes (thickness to be specified by the manufacturer) with water absorption less

than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement

mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement

and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the 0.00 0.00

notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

11.41A.2.5 11.41A.2 Glazed vitrified floor tiles polished finish

11.41A.2.5 Size of Tile 1200 x 1200 mm

11.41A.3.1 Glazed Vitrified tiles Matt/Antiskid finish of size

11.41A.3.1 Size of Tile 600 x 600 mm

12.45 Providing and fixing false ceiling at all heights including providing and fixing of frame work made of special sections, power pressed

from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats

of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling

with dash fastener 12.5 mm dia x 50 mm long with 6 mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm

of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9

mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with

tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing

perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition

with the help of rawl plugs at 450 mm centre, with 25 mm long dry wall screws @ 230 mm interval, including fixing of gypsum board

to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and

finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing

with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per

manufacturer’s specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with

frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but

excluding the cost of painting with :

12.45.4 Fully Perforated Gypsum Plaster Board of size 1200 x 2400x12.5 mm having approx. 15 % perforated area with perforation size and

pattern as approved by the Engineerin- charge and as per manufacturer’s specification, with all 4 sides tapered and backed by

acoustical tissue with NRC

value not less than 0.60

12.50 Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-

Charge) of total coated thickness 0.50 mm (base metal of minimum 0.45 mm thickness with total coating thickness of 0.05mm) with

zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and

52 polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during Sqm 2718.16 738.65 2007768.88 2007768.88

transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed

using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved

surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

12.51 Providing and fixing precoated galvanised steel sheet roofing accessories of total coated thickness 0.50 mm (base metal of minimum

0.45 mm thickness with total coating thickness of 0.05 mm) with Zinc coating 120 gram per sqm as per IS: 277, in 240 mpa steel

grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping

53 screws complete :

13.1 12 mm cement plaster of mix :

13.1.1 1:4 (1 cement: 4 fine sand)

55 13.2.1 15 mm cement plaster on the rough side of single or half brick wall of mix 1:4(1 cement : 4 fine sand mortar) Sqm 3550.52 399.45 1418253.22 1418253.22

13.16 6 mm cement plaster of mix :

1:3 (1 cement : 3 fine sand)

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

13.46 Finishing walls with Acrylic Smooth exterior paint of required shade : 13.46.1 New work (Two or more coat applied @ 1.67 ltr/10

sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm)

13.78 Providing and applying 12mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light

weight aggregates as vermiculite / perlite respectively conforming to IS:2547 (Part 1 & II) 1976, applied on hacked / uneven

background such as bare brick / block / RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc,

13.2.1 Providing and applying 15mm premixed formulated one coat readymade plaster having additives and aggregates produced at

automated dry mixed plant mixed with cement, sand and polymers in ratio 1:4 (1. cement :4 sand and polymers in appropriate ratio)

59 including applying Portland cement slurry on the under layer @o.4oKg/sqm applied on hacked/uneven background such as bare Sqm 4970.72 656.00 3260792.98 3260792.98

brick/cc and Block/RCC work on walls and ceiling at all floors and locations as per manufacturers specification finished in smooth

line and level etc complete.

13.78 Providing and applying 6 mm thick (average) premixed formulated one coat gypsum lightweight plaster having additives and light

weight aggregates as vermiculite / perlite respectively conforming to IS:2547 (Part 1 & II) 1976, applied on hacked / uneven

background such as bare brick / block / RCC work on walls & ceiling at all floors and locations, finished in smooth line and level etc,

13.50 Applying priming coat:

13.50.2 With ready mixed aluminium primer of approved brand and manufacture on resinous wood and plywood

13.62 Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade :

62 13.62.1 Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and sqm 500.86 226.25 113319.58 113319.58

13.80 Providing and applying white cement based putty of average thickness 1mm, of approved brand and manufacturer, over the plastered

wall surface to prepare the surface even and smooth complete.

13.83 Wall painting with premium acrylic emulsion paint of interior grade, having VOC (Volatile Organic Compound ) content less than 50

64 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and Sqm 4690.71 142.80 669833.39 669833.39

colour. 2 Coats.

13.85 Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.

65 13.85.3 With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre Sqm 6035.35 73.95 446314.13 446314.13

13.116 Polishing in high gloss/matt finish melamine clear polish on wood work in required color/wooden shade texture with following

process in the sequence as detailed below:

1. The surface to be polished is rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos.

2. Applying two coats of sealer with spray gun and allowing sufficient drying time for 1st coat and 2nd coat is allowed to dry for 8 to

3. On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make

the surface further smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big

holes/grooves etc. Filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface is further

allowed to dry for 12 hrs.

4. On this, 1st coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required

proportion. This 1st coat is allowed to dry for 24 hrs then this dry surface is again fine wet rubbed smooth, which is further allowed

to dry for 12 hrs. The final melamine polish is applied with compressor pressure spray gun using melamine clear polish and melamine

thinner mixed in required proportion complete as per direction of Engineer-in-Charge. (Finalcoat to be done in 1 or 2 layers without

16.91 Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light

traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required

colour & pattern over 50 mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks

67 into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver Sqm 709.23 1091.50 774124.55 774124.55

blocks as per required size and pattern, finishing and sweeping

extra sand. complete all as per direction of Engineer-in Charge.

16.91.2 80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern.

20.2 Boring, providing and installation bored cast-in-situ reinforced cement concrete piles of grade M-25 of specified diameter and length

below the pile cap, to carry a safe working load not less than specified, excluding the cost of steel reinforcement but including the

cost of boring with bentonite solution and temporary casing of appropriate length for setting out and removal of same and the length

68 of the pile to be embedded in the pile cap etc. by percussion drilling using Direct mud circulation (DMC) or Bailer and chisel 0.00 0.00

technique by tripod and mechanical Winch Machine all complete, including removal of excavated earth with all its lifts and

leads(length of pile for payment shall be measured up to bottom of pile cap).

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

20.6 Vertical load testing of piles in accordance with IS 2911 (Part IV) including installation of loading platform by Kentledge/Anchor

piles method and preparation of pile head or construction of test cap and dismantling of test cap after test etc. complete as per

specification & the direction of Engineer in-charge.

Note: 1. Initial and Routine Load Test shall not be carried out by Dynamic method of testing.

70 Note: 2. Testing agency shall submit the design of loading platform for the approval of Engineer-in-charge.

Group of two or more piles upto 50 tonne Safe capacity

20.6.3.1 Initial test (Test Load 2.5 times the Safe capacity) No. 4.00 70420.50 281682.00 281682.00

20.6.3.2 Routine test (Test Load 1.5 times the Safe capacity) No. 6.00 40545.15 243270.90 243270.90

21.13 Providing and fixing Brass 100mm mortice latch and lock with 6levers without pair of handles (best make of approved quality) for

aluminium doors including necessary cutting and making good etc. complete.

21.14 Providing and fixing Anodized aluminum (Anodized transparent or dyed to required shade according to IS: 1868 minimum anodic

coating of Grade AC 15) sub frame work for windows and ventilators with extruded built up standard tubular sections of approved

makeconforming to IS: 733 and IS: 1285 fixed with dash fastener of required dia and size (dash fastener to be paid separately).

21.18 Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing

and fixing top & bottom pivot & double acting hydraulic floor spring type fixing arrangement and making necessary holes etc. for

fixing required door fittings, all complete as per direction of Engineer-in-charge (Door handle, lock and stopper etc.to be paid

74 NSC-02 P/F of Automatic Glass Door sensors with electric motor and moving system. No 4.00 125000.00 500000.00 500000.00

NSC-03 Providing and fixing Ist quality Moroccan wall tiles of vibrant colours, intricate patterns and rich in cultural heritage size 600 x 1200

(thickness to be specified by the manufacturer), of approved make, fixed withe chemical as approved by Engineer- in-Charge, over 12

mm thick bed of cement mortar 1:3 ( 1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3 kg per sqm, including

pointing in white cement mixed with pigment of matching shade complete.

NSC-04 Providing and fixing Khatambandhi ceiling of appropriate design and pattern in wood (budloo wood) including base work of 12mm

76 thick plywood of approved quality fixed over a framework having section of 2 inches x 2.5 inches jambs and 2 feet x 2 feet c/c Sqm 472.80 7200.00 3404160.00 3404160.00

(budloo wood) including cost of nails, shuttering, scaffolding etc complete job.

NSC-05 Providing 10 mm thick plaster of Paris (gypsum anhydrous) ceiling upto a height of 5 m above floor level over first class kail wood

strips 25x6 mm with 10 mm gap in between and reinforced with rabbit wire mesh fixed to wooden frame

78 NSC-06 Providing and fixing Khutambound ceiling machine made and paper machi touch. Sqm 112.93 16578.00 1872153.54 1872153.54

79 NSC-07 Providing and fixing of ornamental wooden blusters of deodar wood of 250mm dia length 3.60m length. No. 12.00 95000.00 1140000.00 1140000.00

NSC-08 Providing and fixing of 18mm thick HDMR Panelling in skirting of required design and make with necessary fixing arrangements and

screws including drilling necessary holes for rawl plugs etc and priming coat on unexposed surface complete.

81 NSC-09 Providing and fixing of 3D Wallpaper of required design and pattern 220 GSM approved by engineer incharge Sqm 1440.00 510.00 734400.00 734400.00

NSC-10 Duco painting the HDMR surface, incl, cleaning the surface, sandpapering, applying wood filler with Duco putty, applying Duco

primer two coats using spray gun in dust free envirment, sandpapering the surface again, applying Duco paint two coats, final coat

with lacquer with thinner using spray gun. Buffing for high glossy finish polish the surface with rubbing compound, finally buffing

with sealant polish.

NSC-11 Providing and fixing expansion hold fasteners on C.C. /R.C.C./Brick masonry surface backing including drilling necessary holes and

83 the cost of bolt etc complete. Share connectors T-6 @ 12" C/C (V) drilled and gravted in the existing RCC or Brick work. No. 1080.00 40.00 43200.00 43200.00

NSC-12 Brick work with Maharaja brick of size 9'x4.5'x1.5' work for wall lining in super structure upto floor V level,proving 10mm spacer

84 inbetween, back filled with a grout of 12mm thick cement motar 1:3 mix and pointing with cement lime surki motar 1:1:1 including sqm 960.00 1575.00 1512000.00 1512000.00

rubbing and polishing . Incl. all leads and lifts carriage complete job

NSC-13 Providing and fixing of factory made of partitions, thickness as 52.4 mm thick and 1500mm high, including powder coated

aluminium trims. Top block finish be in fabric finish. Bottom block finish be in metal finish. Tiles on main spine: Top tiles are fabric

tackable tile. Bottom tiles - Plain metal. Tiles on Return Panel: Top tiles to be fabric tackable tile. Bottom tiles - Plain metal.

INTERMEDIATE BLOCKS on main spine Intermediate blocks be given in DL +DL finish. Wire Management through main spine-

Wires should be taken into the system through cable ducts from the junction boxes and be carried upto the panels through concealed

conduits inside the blocks. (1800 W x 1500 H ) Panel size.

B Boundary Wall 600 Mtr 0.00 0.00

4.11 Providing and laying damp-proof course 50 mm thick with cement concrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from

natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources).

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using

coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement,

admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and

workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding

5.33 the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of 0 0.00

concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case

2 the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to

either re-design the mix or bear the cost of extra cement.

5.33.1 All works upto plinth level 0 0.00

5.33.1.1 Concrete of M25 grade with minimum cement content of 330 kg /cum Cum 268.47 9504.75 2551740.23 2551740.23

5.33.2 All works above plinth level upto floor V level 0.00 0.00

5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum Cum 59.43 9860.40 586003.57 586003.57

6.4 Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to

3 floor V level in all shapes and sizes in : Cum 214.74 9105.95 1955411.70 1955411.70

6.4.2 Cement mortar 1:6 (1 cement : 6 coarse sand)

9.48.1 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including

priming coat with approved steel primer all complete. Fixed to steel wimdow by weilding

5 13.7 12mm Cement plaster of mix: 13.7.2 1 : 4 ( 1 cement : 4 fine sand) Sqm 684.00 425.55 291076.20 291076.20

13.46 Finishing walls with acrylic smooth exterior paint of required shade on New work (Two or more coats applied @ 1.67 liter/10sqm

over and including priming coat of exterior primer applied @ 2.20kg/10sqm)

13.50 Applying priming coat:13.58.3 With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel

galvanized iron/steel works

13.85 Applying priming coats with primer of approved brand and manufacture, having low VOC (Volatile Organic Compound ) content.

13.85.3 With water thinnable cement primer on wall surface having VOC content less than 50 grams/litre 0.00 0.00

13.53 Painting on G.S sheets with synthetic enamel paint of approved band and manufacture of required colour to give an even shade on

New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution.

16.53 Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90

m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron ‘Y’ shaped placed 2.4m or 3.00 m apart

and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary

bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) /

Spring core (2.5 mm thick) wire of high tensile strength of 165 kg/ sq. mm with tape (0.52 mm thick) and weight 43.478 gm/ metre

(cost of M.S. angle, C.C. blocks shall be paid separately)

C Gates 0.00 0.00

Providing and laying in position ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using

coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement,

admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and

workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding

1 5.33 the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge, for the following grades of 0 0.00

concrete.: Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case

the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to

either re-design the mix or bear the cost of extra cement.

5.33.2.1 Concrete of M25 grade with minimum cement content of 330 kg /cum Cum 15.20 9860.40 149878.08 149878.08

10.25 Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of

2 approved steel primer using structural steel etc. as required. 10.25.2 In gratings, frames, Kg 1605.31 172.60 277076.51 277076.51

guard bar, ladder, railings, brackets, gates and similar works

13.50.3 Applying priming coat: With ready mixed red oxide Zinc Chromate primer of approved brand and manufacture on steel galvanized

iron/steel works

13.53 Painting on G.S sheets with synthetic enamel paint of approved band and manufacture of required colour to give an even shade on

New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution.

5 NSC-14 Providing and laying stone soling hand packed.incl all leads lifts, carriage complete. Cum 5.09 2898.50 14753.37 14753.37

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

NSC-15 Providing and laying one side Face fine chisel dressed (Deveri )stone work 200-225 mm width in 1:4 mortar,Incl. pointing with 1:2

6 mortar mixed with pigmentt to match the colour of stone,cost of scofolding for arch work in super stucture upto floor two Sqm 53.18 6000.00 319080.00 319080.00

level,carriage complete.

D Road Network 1500 Sqm 0.00 0.00

16.1 Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of

1 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the Sqm 1800.00 218.90 394020.00 394020.00

sub grade and disposal of surplus earthwith lead upto 50 metres

16.2 Extra for compaction of earth work in embankment under optimum moisture conditions to give at least 95% of the maximum dry

density (proctor density).

16.30 Providing and applying tack coat using hot straight run bitumen of grade VG - 10, including heating the bitumen, spraying the

bitumen with mechanically operated spray unit fitted on bitumen boiler, cleaning and preparing the existing road surface as per

16.30.1 On W.B.M. @ 0.75 Kg / sqm

16.54 Providing and laying Dense Graded Bituminous Macadam using crushed stone aggregates of specified grading, premixed with

bituminous binder and filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor

to the required grade, level and alignment and rolling with smooth wheeled, vibratory and tandem rollers as per specifications to

4 achieve the desired compaction and density, complete as per specificatons and directions of Engineer-in-Charge. Cum 135.00 11129.55 1502489.25 1502489.25

16.54.1 50 to 100 mm average compacted thickness with bitumen of grade VG-30 @ 5% (percentage by weight of total mix) and

lime filler @ 2% (percentage by weight of Aggregate) prepared in Batch Type Hot Mix Plant of 100-120 TPH capacity.

16.57 Providing and laying Bituminous concrete using crushed stone aggregates of specified grading, premixed with bituminous binder and

filler, transporting the hot mix to work site by tippers, laying with paver finisher equiped with electronic sensor to the required grade,

level and alignment and rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction and density as

5 per specification, complete and as per directions of Engineer-in-Charge. 16.57.2 40/50 mm Cum 72.00 12708.75 915030.00 915030.00

compacted thickness with bitumen of grade VG- 30 @ 5.5% (percentage by weight of total mix) and lime filler @ 3% (percentage by

weight of Aggregate) and waste plastic additive @ 8% (percentage by weight of bitumen) prepared in Batch Type Hot Mix Plant of

100- 120 TPH capacity.

16.59 Manufacturing, supplying and fixing retro reflective sign boards made up of 2 mm thick aluminium sheet, face to be fully covered

with high intensity encapsulated type heat activated retro reflective sheeting conforming to type - IV of ASTM-D 4956-01 in blue

and silver white or other colour combination including subject matter, message (bi-lingual), symbols and borders etc. as per IRC ;

67:2001, pasted on substrate by an adhesive backing which shall be activated by applying heat and pressure conforming to class -2 of

ASTM-D-4956-01 and fixing the same with suitable sized aluminium alloy rivets @ 20 cm c/c to back support frame of M.S. angle

iron of size 25x25x3 mm along with theft resistant measures, mounted and fixed with 2 Nos. M.S. angles of size 35x35x5 mm to a

vertical post made up to M.S. Tee section ISMT 50x50x6 mm welded with base plateof size 100x100x5 mm at the bottom end and 0.00 0.00

including making holes in pipes, angles flats, providing & fixing M.S. message plate of required size, steel work to be painted with

two or more coats of synthetic enamel paintof required shade and of approved brand & manufacture over priming coat of zinc

chromate yellow primer (vertical MS-Tee support to be painted in black and white colours). Backside of aluminium sheet to be

painted withtwo or more coats of epoxy paint over and including appropriate primingcoat including all leads and lifts etc. complete as

per drawing , specification

and direction of Engineer-in-charge

16.59.1 Mandatory/ Regulatory sign boards of 900 mm diametre with support length of 3750 mm No 3.00 7183.35 21550.05 21550.05

16.59.2 Cautionary /warning sign boards of equilateral triangular shape having each side of 900 mm with support length of

16.60 Manufacturing, supplying and fixing retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully

covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-

4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground

and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure

conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized

aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with

theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of

aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, lowering down the

structural frame work from the gantry, fixing and erecting the same in position all complete as per drawings, specification and

direction of the engineer-in-charge.(Structural frame work including M.S. plate to be provided separately. Rectangular area of the

sheet only shall be measured for payment).

16.60.1 Overhead informatory road signage

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

16.62 Providing and applying 2.5 mm thick road marking strips (retro- reflective) of specified shade/ colour using hot thermoplastic

material by fully/ semi automatic thermoplastic paint applicator machine fitted with profile shoe,glass beads dispenser, propane tank

8 heater and profile shoe heater, driven by experienced operator on road surface including cost of material, labour, T&P, cleaning the Sqm 115.80 747.80 86595.24 86595.24

road surface of all dirt, seals, oil, grease and

foreign material etc. complete as per direction of Engineer-in-charge andaccordance with applicable specifications.

16.78 Construction of granular sub-base by providing close graded Material conforming to specifications, mixing in a mechanical mix plant

at OMC, carriage of mixed material by tippers to work site, for all leads & lifts, spreading in uniform layers of specified thickness

9 with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per Cum 540.00 2784.00 1503360.00 1503360.00

specifications and directions of Engineerin- Charge.

16.78.1 With material conforming to Grade-I (size range 75 mm to 0.075 mm) having CBR Value-30

16.79 Providing, laying, spreading and compacting graded stone aggregate (size range 53 mm to 0.075 mm ) to wet mix macadam (WMM)

specification including premixing the material with water at OMC in for all leads & lifts, laying in uniform layers with mechanical

10 paver finisher in sub- base / base course on well prepared surface and compacting with vibratory roller of 8 to 10 tonne capacity to Cum 540.00 2914.30 1573722.00 1573722.00

achievethe desired density, complete as per

specifications and directions of Engineer-in-Charge.

E Footpaths 350Mtr 0.00 0.00

16.69 Providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line,

level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves

3 (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required Cum 27.36 10117.60 276817.54 276817.54

complete etc. as per direction of Engineerin- charge (length of finished kerb edging shall be measured to calculate volume for

payment). (Precast C.C. kerb stone shall be approved by Engineer-in-charge).

16.88 Providing and laying matt finished vitrified tile of size 100x100x16 mm having water absorption less than 0.5% and conforming to IS:

15622 of approved make in all colours and shades in out door floors such as footpath, court yard multi models etc., laid on 20 mm

thick base of cement mortar 1:4 (1cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement

mixed with matching pigments etc.complete as direction of Engineer-in-Charge.

F Landscaping 500 Sqm 0.00 0.00

2.1 Earth work in surface excavation not exceeding 30 cm in depth but exceeding 1.5 m in width as well as 10 sqm on plan including

1 getting out and disposal of excavated earth upto 50 m and lift upto 1.5 m, as directed by Engineer-in- Charge: 0 0.00

2.2 Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be

reduced by 20% for payment).

2.4 Supplying and stacking at site dump manure from approved source, including carriage upto 5 km lead complete (manure measured in

stacks will be reduced by 8% for payment) :

2.4.1 2.4.1 Screened through sieve of I.S. designation 20 mm Cum 69.30 391.35 27120.56 27120.56

4 2.7 Fine dressing of the ground. Sqm 600.00 5.60 3360.00 3360.00

2.3 Supplying and stacking sludge at site including royalty and carriage upto 5 km lead complete (sludge measured in stacks will be

reduced by 8% forpayment

6 2.27 Supplying and spreading of sand in lawn area, including watering, and dressing complete Cum 49.50 2088.90 103400.55 103400.55

2.8 Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump

manure and/ or good earth to be paid separately).

8 2.9 Mixing earth and sludge or manure in the required proportion specified or directed by the Officer-in-charge Sqm 600.00 59.70 35820.00 35820.00

2.33 Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level

and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light

waterning with sprinkler and maintenancefor 30 days or more till the grass establish properly, as per direction of

officer-in-charge.

2.28 Surface dressing of the ground including removing vegetation and inequalities not exceeding 15 cm deep and disposal of rubbish, lead

2.28.1 All kinds of soil 0.00 0.00

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water

proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing

cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242

kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed

with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes

and masonry with polymer mixed slurry.

9.48.1 Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including

2 priming coat with approved steel primer all complete. Fixed to steel window by welding Kg 174.96 219.10 38333.74 38333.74

B Sanitary Works 0.00

SH: I China Ware 0.00

Providing and fixing white glazed vitreous china wall mounting type (European type) water closet with C.P. bolts, nuts, C.I. Chair or

other hanging arrangement, white solid plastic seat with lid, C.P. brass hinges and rubber buffers, white vitreous china dual flushing

1 NSC-16 cistern with push plates(6/3 lit.) and PVC connector, C.P. brass screws and washers complete, including cutting and making good Each 50.00 15000.00 750000.00 750000.00

the walls floors where required.(As per Green Building, Water Closet <1.3 GPF). Standard quality Wall hung EWC white plastic

seat with lid & CP brass hinges.

Providing and fixing Table top wash basin (Countertop Basin ),with 32 mm Waste Coupling and other allied accessories including

2 NSC-17 cutting and making good the walls wherever required:- White Vitreous China TableWash basin. Size 18" dia meter round basin Each 52.00 6000.00 312000.00 312000.00

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per I.S. 13983 with C.I. brackets and stainless steel plug 40 mm,

including painting of fittings and brackets, cutting and making good the walls wherever required :

3 17.10.1.1 Kitchen sink with drain board Each 13.00 6945.60 90292.80 90292.80

510x1040mm bowl depth 250mm

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 610 x 390 x 370 mm having

4 17.80 pre & post flushing with water (250 ml & 500 ml consumption), having water inlet from back side, including fixing to wall with Each 18.00 7979.20 143625.60 143625.60

suitable brackets all as per manufacturers specification and direction of Engineer-in-charge.

SH:II C.P Fitting and Accessories 0.00 0.00

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.

15 mm nominal dia

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of

7 17.32.4 approved make and shade with 6 mm thick hard board backing Each 52.00 2093.00 108836.00 108836.00

Rectangular shape 1500x450 mm

8 17.34.1 Providing and fixing toilet paper holder C.P Brass Each 51.00 803.70 40988.70 40988.70

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to European type W.C. of

quality and make as approved by Engineer - in - charge

Providing and C.P. brass angle valve for basin mixer and geyser points of approved make conforming to IS : 8931 15 mm nominal

11 NSC-18 Providing and fixing C.P Brass Soap Dish. Each 52.00 1022.94 53192.76 53192.76

12 NSC-19 Providing and fixing CP brass towel rail complete with CP brackets fixed to wooden cleats with CP brass screws . Each 52.00 1787.17 92932.71 92932.71

13 NSC-20 Providing and fixing CP Short Body Bibcock with Valve Flange Each 51.00 1283.97 65482.62 65482.62

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge with Health

15 mm nominal dia

Providing and fixing Stainless Steel Retractable Sink Basin Water Drain Pipe of approved quality & make and as per the direction of

Engineer-in-charge. (For Kitchen Sink)

16 NSC-23 Providing and fixing CP Brass Sink Mixer with Regular Swivel Spout of quality & make as approved by Engineer in charge. Each 13.00 7691.00 99983.00 99983.00

Providing and fixing Stainless Steel Retractable Sink Basin Water Drain Pipe of approved quality & make and as per the direction of

Engineer-in-charge. (For Kitchen Sink)

18 NSC-25 Providing and fixing CP Brass Sink Mixer with Regular Swivel Spout of quality & make as approved by Engineer in charge. Each 13.00 7691.00 99983.00 99983.00

SH III : SOIL, WASTE AND VENT PIPES 0.00 0.00

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1

cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4

coarsesand (zone- III) : 8 graded stone aggregate 40 mm nominal size),inside plastering 12 mm thick with cement mortar 1:3 (1

cement : 3coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse

sand : 4graded stone aggregate 20 mm nominal size) finished with a floatingcoat of neat cement complete as per standard design :

Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of

cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Excavation work by mechanical means (Hydraulic excavator)/ manual means in foundation trenches or drains (not exceeding 1.5m in

20 2.9.1 width or 10 sqm on plan), including dressing of sides and ramming of bottoms,lift upto 1.5 m, including getting out the excavated soil cum 438.00 632.95 277232.10 277232.10

and disposal of surplus excavated soils as directed, within a lead of 50 m. ordinary Rock

Providing and fixing soil, waste and vent pipes IS 13592 & fittings (IS: 14735 ) suitable to rubber ring joints , which includes bends,

22 NSC-26 rubber ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing 0.00 0.00

design .etc. complete including jointing.

a NSC-26 A 110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B Rmt 1176.00 531.25 624754.10 624754.10

b NSC-26 B 75 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B Rmt 330.00 375.99 124076.31 124076.31

Providing and fixing of Rain Water pipes IS 13592 & fittings (IS: 14735 ) suitable to rubber ring joints , which includes bends, rubber

ring, jointing, junctions, clean out plug , cowls, offsets, collar, M.S holder-bat clamps, access pieces, trap of self cleansing design .etc.

complete including jointing.

110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-A

Providing and Fixing of Floor Traps 110 mm with double chrome plated Cover one Grated and one closed and all other fittings

25 NSC-29 Supply, Installation of PVC Gully Trap of Size 110 mm Each 27.00 2808.34 75825.30 75825.30

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to

27 NSC-31 haunches of P.V.C pipes including bed concrete as per standard design : Metre 438.00 590.00 258420.00 258420.00

110 mm dia. PVC SWR socketed pipe with rubber ring joints as per IS:13592 Type-B

SH IV: WATER SUPPLY 0.00 0.00

Providing and fixing unplasticised PVC connection pipe with brass unions:

45 cm length 15 mm nominal bore

30 18.76.1 Cutting holes upto 30x30 cm in walls including making good the same with common burnt clay F.P.S.(non modular) bricks Each 210.00 416.80 87528.00 87528.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot and cold water supply, including

all CPVC plain and brass threaded fittings. includes fixing the pipe with clamps at 1.00 meter spacing including jointing of pipes and

fitting one step CPVC solvent cement and tesing of joints Complete in the direction of Engineering in charge.

a 18.7.1 15mm nominal outer dia pipes metre 1020.00 286.80 292536.00 292536.00

b 18.7.2 20mm nominal outer dia pipes metre 132.00 335.00 44220.00 44220.00

c 18.7.3 25mm nominal outer dia pipes metre 60.00 401.55 24093.00 24093.00

d 18.7.4 32mm nominal outer dia pipes. metre 48.00 518.75 24900.00 24900.00

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all

CPVC plain & brass threaded fittings and fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with

32 18.8 one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per 0.00 0.00

direction of Engineer in Charge.

Concealed work, including cutting chases and making good the walls etc.

a 18.8.2 20mm nominal outer dia pipes. metre 156.00 537.60 83865.60 83865.60

b 18.8.3 25mm nominal outer dia pipes. metre 336.00 627.25 210756.00 210756.00

c 18.8.4 32mm nominal outer dia pipes. metre 36.00 739.30 26614.80 26614.80

29 A 40mm nominal outer dia pipes. metre 48.00 851.35 40864.80 40864.80

30 B 50mm nominal outer dia pipes. metre 6.00 963.40 5780.40 5780.40

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all

CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching,

refilling & testing of joints complete as per direction of Engineer in Charge.

a 18.9.5 40mm nominal outer dia pipes. metre 420.00 563.05 236481.00 236481.00

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Supplying and Fixing of Elastomeric foam Insulation made from Nitrile Rubber with Density not less than 50 Kg/Cu.m,Thickness 10

mm for a Temp Range of -40 Deg C to 105 Deg C

SH:VI PVC STORAGE TANKS,VALVES AND GEYSERS 0.00 0.00

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable

35 18.48 locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for Per Liter 33000.00 11.00 363000.00 363000.00

Providing & fixing full way lever operated forged brass ball valve of brass body with forged brass hard chrome plated steel ball tested

to a pressure not less than 16 Kg / sqcm with threaded / flanged joints complete with nuts, bolts, gaskets, washers etc.

37 F Providing and fixing on wall 35 LTRS Electric Geyser with ABS Body. Each 10.00 14070.00 140700.00 140700.00

37 G Providing and fixing on wall 50 LTRS Electric Geyser with ABS Body. Each 34.00 22178.00 754052.00 754052.00

Supply,Installation,Testing and Commissioning of Open Well Submersible Pump with a Discharge of 15 Cu.m/hr @Head of 60

Meters Complete with all accessories including header Pipes, allied materials and automatic Control Panel.

Borewell 0.00 0.00

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including

collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all

1 23.2.2.1 equipments, tools,plants & machineries required for the job, all complete as per direction of Engineer -in-charge, beyond 90 metre & metre 180.00 1870.60 336708.00 336708.00

upto 150 metre depth below ground level.

Rocky strata including Boulders.300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 mild steel

screwed and socketed/plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including

2 23.10.3 painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & metre 90.00 2442.75 219847.50 219847.50

labour charges,fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia

having minimum wall thickness 5.40 mm

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW (Electric Resistance Welded) FE 410 plain slotted

(having slot of size 1.6/3.2 mm) mild steel threaded and socketed/ plain bevel ended pipe (type A) of required dia, conforming to IS:

8110, of reputed and approved make, having wall thickness not less than 5.40 mm, including painted with outside surface with two

coats of anticorrosive bitumestic paint of approved brand and manufacture,including hire & labour charges, fittings & accessories, all

complete,for all depths, as per direction of Engineer -in-charge.

200 mm nominal size dia

Gravel packing in tubewell construction in accordance with IS: 4097,including providing gravel fine/ medium/ coarse, in required

grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS:11189, to establish maximum rate of usable water yield

without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till

well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw

down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell,

all complete, including hire & labour charges of air compressor, tools & accessories etc.,all as per requirement and direction of

Engineer-in-charge.

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I),

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).

Supply,Installation,Testing and Commissioning of Vertical type Submersible Pump with suitable discharge and head Complete with

all accessories including header Pipes, allied materials and automatic Control Panel.

C Fire Fighting System 0.00

PIPES & ACCESSORIES 0.00

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50

1 4.6 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. 0.00

suspenders including G.I. bolts & nuts, etc. as required.

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

a 4.6.4 300mm (W) x 50 mm (H) wide cable tray perforated type Rmt 60.00 1062.00 63720.00 63720.00

b 4.6.3 225mm (W) x 50 mm (H) wide cable tray perforated type Rmt 60.00 991.00 59460.00 59460.00

c 4.6.1 100mm (W) x 50 mm (H) wide cable tray perforated type Rmt 60.00 754.00 45240.00 45240.00

Earthing with G.I. earth pipe 4.5 Meter long, 40 mm dia including accessories, and providing masonry enclosure with cover plate

having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating

3 5.9 with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring Rmt 48.00 160.00 7680.00 7680.00

washer spaced at 50mm)

Supply and Making end Termination with Brass Compression Gland and Aluminium/Copper Lugs for the Following Sizes of PVC

insulated and PVC Sheathed/XLPE Aluminium Conductor Cable of 1.1 KV Grade as Required (Comet)

Supply and Making end Termination with Brass Compression Gland and Aluminium/Copper Lugs for the Following Sizes of PVC

insulated and PVC Sheathed/XLPE Aluminium Conductor Cable of 1.1 KV Grade as Required (Comet)

c A 12 C X 2.5 Sq.mm Copper Armoured Nos 2.00 500.00 1000.00 1000.00

d B 3 C X 2.5 Sq.mm Copper Armoured Nos 2.00 175.00 350.00 350.00

e C 4 C X 2.5 Sq.mm Copper Armoured Nos 2.00 150.00 300.00 300.00

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903

suitable for instantaneous connection to interconnect hose pipe coupling as required :

a)Supplying, installation, testing and commissioning of Electric driven Main Fire Pump conforming to IS 12469: 2019 suitable for

automatic operation and consisting of following, complete in all respects, as required :

(b) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft,

mechanical seal as required.

6 27.1 (c) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 0 0.00

Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-12615:

(d) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required.

(e)Suitable cement concrete foundation duly plastered with anti vibration pads.

Supplying, installation, testing and commissioning of diesel engine driven main fire pump suitable for automatic operation and

consisting of following,complete in all respects, as required : (Diesel Driven Pump) Horizontal type, multistage, centrifugal pump of

cast of iron body and bronze impeller with stainless steel shaft,mechanical seal conforming to IS 1520.Suitable HP, 1500 RPM water

cooled with radiator,diesel engine conforming to relevant IS standard complete with auto starting mechanism, 12 /24 volts electric

starting equipment, diesel tank, exhaust pipe extended upto 10 m outside pump house duly insulated with 50 mm thick glass wool

with 1.0 mm thick aluminium sheet cladding, residential silencer,instruments and protection as per standard specification, stop

solenoid for auto stop in the event of fault with audio indications, painted with post office red colour etc. as required. M.S

fabricated, common base plate, coupling, coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly

plastered and with anti vibration pads.

Supplying, installation, testing and commissioning of electric driven pressurisation pump suitable for automatic operation and

consisting of following, complete in all respects, as required : (Jockey Pump) Horizontal type, multistage, centrifugal pump of cast

iron body and bronze impeller with stainless steel shaft, mechanical seal conforming to IS : 1520. Suitable HP squirell cage induction

motor TEFC type suitable for operation on 415 volts, 3 phase 50 Hz AC supply with IP 55 class of protection for enclosure,

horizontal foot mounted type with Class-'F' insulation, conforming to IS : 325. M.S.fabricated Common base plate, coupling,

coupling guard, foundation bolts etc. as required. Suitable cement concrete foundation duly plastered and with anti vibration pads.

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Fabrication, supply, Insallation testing & commissioning of Electrical control panel of cubical construction, floor mounted type,

fabricated out of 2mm thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of

approved shade after 7 tank treatment process, cable alley, interconnection with suitable size copper conductor cable/solid copper

9 27.5 strip, having switchgears and accessories, mountings and internal wiring, earth terminals, numbering etc. complete in all respect, 0 0.00

suitable for main fire pump, pressurisation pump & diesel pump set complete as per CPWD specification with following in coming

and Outgoings, suitable for operation on 415V, 3 phase, 50Hz Ac Supply with enclosure protection class IP 42 as required :

630A, 50kA 4 Pole MCCB, Ics=100% Icu Rating Digital Voltmeter 0-500V with selector switch Ammeter (0-630 A) with selector

swtich & CTs etc. LED type RYB phase indicating lamps, ON, OFF, trip indicating lamps Set of Copper Bus Bar 800Amps

(Note : All outgoing feeders for pumps should have digital Ammeter with selector switches, and LED type ON, OFF, trip indicating

200 Amp, 50kA TPN MCCB, Ics=100% Icu, with fully automatic Star/Delta starter suitable for 75 hp pump with overload

protection, current sensing type single phase

preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote,

auto/manual/OFF operation. - 2 sets

Jockey Pump 100 Amp, 50kA TPN MCCB, Ics=100% Icu, with Suitable HP fully automatic Star/Delta starter with overload

protection, current sensing type single phase preventor complete with all acceessories and internal wiring required for automatic

operation, selector switch for local/remote, auto/manual/OFF operation. - 2 sets

a 27.5.5 DIESEL ENGINE CONTROL Each 1.00 469546.00 469546.00 469546.00

Control for diesel engine comprising - Automatic/Manual selctor switch & 3 attempts starting device, timers and relays as required,

push buttons, start/stop in manual mode Indicating lamp for high/ Low Lub. Oil pressure, High Water Temp and Engine on indication

Battery charger suitbale for 12V/24 V DC with boost and trickle selector switch, 0-30 V DC volt meter, and 0- 20 A DC Ammeter

All standard relays and accessories for automatic operation of diesel engine System Controller

(Note : All outgoing feeders for pumps should have digital Ammeter with selector switches, and LED type ON, OFF, trip indicating

lamps) Main Fire Pump 200 Amp, 50kA TPN MCCB, Ics=100% Icu, with fully automatic Star/Delta starter suitable for suitable hp

pump with overload protection, current sensing type single phase

preventor complete with all acceessories and internal wiring required for automatic operation, selector switch for local/remote,

auto/manual/OFF operation. - 2 sets

100 Amp, 50kA TPN MCCB, Ics=100% Icu, with Suitable HP fully automatic Star/Delta starter with overload protection, current

sensing type single phase preventor complete with all acceessories and internal wiring required for automatic operation, selector

switch for local/remote, auto/manual/OFF operation. - 2 sets

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees,

flanges, tapers, nuts bolts,gaskets etc. in ground including welding, excavation & providing cement concrete blocks as

10 27.6 supports,anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as 0 0.00

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding,

11 27.7 fittings like elbows, tees, flanges,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support 0.00 0.00

frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with

12 27.9 cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : 0 0.00

27.9.1 Single headed Gunmetal Set 6.00 8208.00 49248.00 49248.00

Supplying and fixing single headed External hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with

13 27.10 cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required : Set 10.00 8208.00 82080.00 82080.00

27.10.1 Single headed Gunmetal 0.00 0.00

Supplying and fixing orifice plate made out of 6 mm thick Stainless steel (Grade 304) with orifice of required size to be fitted

14 27.13 between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete Each 16.00 1436.00 22976.00 22976.00

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire,

rivets etc. conforming to IS 636 (type-A) as required :

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red,conforming to IS 884 complete with

the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm

nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser

with 25 mm dia stop gun metal valve & M.S. Pipe and socket.

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap

and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and

18 27.20 flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and Set 1.00 19402.00 19402.00 19402.00

paintingwith synthetic enamel paint of approved shade as required.

Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required

b 27.21.2 Upright Sprinkler Each 22.00 599.00 13178.00 13178.00

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on

reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male

thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of

following sizes complete as required.

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete

with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete

with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required : 32 mm dia

Supplying, fixing, testing & commissioning of double flanged sluice valve of rating PN 1.6 with non rising spindle, bronze/gun metal

seat, ISI marked complete with nuts, bolts, washers, gaskets and conforming to IS 780 of following sizes as required :

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber

gasket, GI bolts, nuts, washers etc.as required :

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber

gasket, GI bolts, nuts, washers etc.as required :

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade

304, sheet with 3 mm dia holes with stainless steel flange.

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade

304, sheet with 3 mm dia holes with stainless steel flange.

26 27.22 Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required. Each 4.00 1670.00 6680.00 6680.00

Supplying, fixing, testing and commissioning of Dismantling Joint of PN 1.6 rating of Ductile Iron ISI marked complete with nuts,

bolts, washers, gaskets of following sizes as required :

28 NSFF-05 Providing and fixing standard fireman's axe with heavy insulated rubber handle conforming to IS: 926 complete. 0.00 0.00

Supply, installation, testing & commissioning of Gun Metal Fire brigade suction hose coupling (Draw-out Connection) with nut for

29 NSF-01 female coupling as per IS:902-1974 complete with 100 mm dia. GI suction pipe and 100 mm dia. 1 No. CI foot valve flanged (to be Each 2.00 10988.20 21976.41 21976.41

connected to static water tank).

Providing and fixing Weather proof hose cabinets for yard hydrant fabricated from 16 g MS sheet with full glass door and

locking arrangement, suitable to accommodate one hydrant valve, 2 nos.15m long hose, 1 No branch pipe and one fireman's axe. The

cabinet shall be painted with one coat of primer and finished stove enamelled "Fire Red", "Fire Hose" written on front including

suitably mounted on a raised masonry platform as required. (Approx 0.75mx0.6 mx 0.25 m).

Providing, fixing, testing and commissiong of double flanged vertical air vessel fabricated from 10mm MS plate with dished ends

from 10mm MS plate, outside with one coat of primer and two coats of synthetic enamel paint of approved shade, complete with

approved quality of pressure switches, pressure gauge and all other required accessories to operate commonly main fire pump,

sprinkler pump and Jockey pump at drop of pressure, automatically at required pressure setting :

Recommended dia. : 450mm

Height of shell : 2000mm

Working pressure : 12.0 kg/cm2

Test Pressure : 18 kg/cm2

Supply, installation, testing & commissioning of pressure gauges with isolation cocks and chrome plated copper pipes as hydrant

station to read pressure from 0-25 kg/cm2 complete and of dial dia 150 mm

Providing and fixing brass/bronze lever operated ball valve of full flow with stainless steel ball (AISI 304 and spindle AISI 410) with

setting and gland of superior quality having minimum working pressure of 20 kg/cm2. 20 mm dia

Providing and Fixing of Electromagnetic Type 150 mm Dia Flow meter made out of SS 304 Material with pressure withstand

capacity of 25 Kg/Sq.cm with Flange End Connection for the test run pipe.

Supply and installation of Following Sizes of Puddle Flanges made out of high quality G.I Pipe.The puddle flange to be tested up to

25 bar water pressure and should work excellently on any weather conditions. (For Details Refer the Drawing)

Supply, installation, testing and commissioning of Rubber Expansion Joint, Rubber Bellows (Flexible coupling) with required

36 NSF-08 flanges,nuts,bolts & accessories 0.00 0.00

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Signage with printed "IN CASE OF FIRE, USE STAIRS UNLESS INSTRUCTED OTHERWISE" of 1.5cm height letters in red

a NSF-10 with white back ground. The size of the board shall be 25cm x 30 cm and shall be fixed at the height of 2 mts. from finished floor Nos 5.00 450.00 2250.00 2250.00

near Manual call points.

Floor identification signage ( i.e., GROUND FLOOR …etc.) at each stair enclosure on every floor, indicating the floor number in

words, lettering size shall be 7.5 cm with contrasting color from back ground. Size shall be 15cm x 60cm.

Fire Exit signage at each stair on every floor, indicating the direction of fire exit, lettering size shall be 7.5 cm with contrasting color

from back ground. Size shall be 15cm x 60cm.

Supplying and Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct

38 NSF-13 in groundin Existing DWC Pipe including excavation, sand cushioning, protective covering and refilling the trench etc as required. 0.00 0.00

c C 12 C X 2.5 Sq.mm Copper Armoured Rmt 60.00 573.59 34415.66 34415.66

d D 3 C X 2.5 Sq.mm Copper Armoured Rmt 60.00 186.08 11164.61 11164.61

e E 4 C X 2.5 Sq.mm Copper Armoured Rmt 60.00 232.17 13930.15 13930.15

Supply, installation, testing and commissioning of 1 cu m/hr Open Well Type Submersible Pump including the cost of Electrical

Panel with Following Specifications:- Flow Rate:- 1.2 cu .m/hr,Head 20 mtr,Motor Body:-SS,Casing:- cast iron

C Total Fire Fighting System (C,)= 0.00 8232817.00 945042.76 9177859.76

D Electrical Work 0.00 0.00

Sub Head-I(Wiring) 0.00 0.00

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor

1 1.10 single core cable in surface/recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing 0.00 0.00

the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required.

Wiring for Light /Power Plug with 2 x 4 sq.mm FRLS PVC Insulated Copper Conductor single core cable in surface/Recessed

2 1.12 medium class PVC Conduit along with 1 No. 4 sq.mm FRLS PVC Insulated copper conductor single core cable for loop earthing as Metre 3840.00 373.00 1432320.00 1432320.00

Wiring for Circuit/Submain Wiring along with earth Wire with the following Sizes of FRLSPVC insulated copper conductor,single

core Cable in surface/Recessed medium class PVC conduit as required.

Wiring for Circuit/Submain Wiring along with earth Wire with the following Sizes of FRLSPVC insulated copper conductor,single

core Cable in surface/Recessed medium class PVC conduit as required.

g 1 R x 70 Sq.mm Copper Multistrand Wire Metre 120.00 3200.00 384000.00 384000.00

Supplying and drawing following sizes of FRLS PVC insulated copper conductor, single core cable in the existing surface/ recessed

4 1.17 steel/ PVC conduit as required. 0 0.00

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including

connections but excluding modular plate etc. as required.

6 1.26 Supplying and fixing modular blanking plate on the existing modular plate and switch box excluding modular plate as required Each 480.00 47.00 22560.00 22560.00

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing

3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and Fixing suitable size G.I box with modular plate and cover in front on surface or in recess,including providing and fixing

6 pin 15/16 amps modular socket outlet and 15/16 amps modular switch,connection,painting etc. as required.

9 1.38 Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required. Each 6.00 112.00 672.00 672.00

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing

2 nos. 3 pin 5/6 A modular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required.

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25

A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Supplying and fixing following way, single pole and neutral, sheet steel, MCB distribution board, 240 V, on surface/ recess, complete

12 2.3 with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. 0.00 0.00

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/

13 2.4 recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing 0.00 0.00

etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/

NSEE-02 recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing 0.00 0.00

etc. as required. (But without MCB/RCCB/Isolator)

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess including cutting the

wall and making good the same in case of recessed conduit as required.

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of

following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.

b 2.10.2 Single pole and neutral Each 130.00 643.00 83590.00 83590.00

16 2.11 Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required. Each 315.00 14.00 4410.00 4410.00

Supplying and fixing 40 A to 63 Arating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of

17 NSEE-03 following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required. Each 50.00 1123.00 56150.00 56150.00

Single pole and neutral

Supplying and fixing following rating, Four pole, 415 V, 10 Ka M.C.B in the existing MCB DB complete with connections, testing

and commissioning etc. as required.

Supply,Installation,Testing and Commissioning 486 Cu.m/Hr. AC 220-240 Volts, 50 Hz exhaust fan made out of Metal Body with

19 NSEE-05 inbuilt thermo cutoff Protection and Noise Level not exceeding 37 dB of Following Sizes including connection etc. complete as Each 42.00 3110.00 130620.00 130620.00

required . 300 mm

Supplying, installation, Testing & Commissioning of LED Recessed/ surface Down lighter (Round/ square/ Rectangular) SMD type

of following body material with PMMA and prismatic diffuser and construction as per IS : 10322 with driver as per the requirement

with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -15 deg to 40 deg

centigrade, internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI

>80 , Flicker free (flicker should be below 5%), life time (LED,Driver & electrical circuitary), of minimum 50000 Burning Hours

with 70% of initial Lumen maintained till life ends , CCT 3000°K / 4000°K / 5700°K / 6000°K / 6500°K (As per ANSI

Bin), SDCM (Standard Deviation Color Matching) <3, Maximum power consumption should not more than the specified rating

20 NSEE-06 and Fixture shall be confirming to relevant BIS standards and trade mark certificate (T.C.). Manufactures Word Mark/ Name 0.00 0.00

Engraved/ Embossing/ Screen printing on housing Complete in all respect i/c connections with 1.5 sq mm FRLS, PVC

insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen

efficacy ≥105 and <120 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED fixtures

as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement.

(Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C) Powder

coated die cast /Extruded aluminum Body including trim & Isolated driver

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

LED Panel light 2x2 ft. (System lumen efficacy ≥120 <135 lm/Watt) 0.00 0.00

Supplying of Panel light 2x2 ft., of following body material and construction as per IS : 10322 with driver as per the requirement with

Driver efficiency >85%, Operating voltage AC 140-270 Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade,

internal surge protection of 2.5 KV with Short & Open circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, Flicker free,

(flicker should be below 5 %), life time (LED,Driver & electrical circuitary), of minimum 50000 Burning Hours with , 70% of initial

Lumen maintained till life ends,CCT

3000°K / 4000°K / 5700°K / 6000°K / 6500°K (As per ANSI Bin),SDCM(Standard Deviation Color Matching) <3, Maximum power

consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark certificate (

T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c connections

with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM

warranty and Isolated Driver. System lumen efficacy ≥120 <135 lm/Watt output . LM79 & LM80 Test report from NABL lab for all

testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as

per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above

CRCA Sheet Body (Thickness > 0.50 mm) 36 watt

Supplying, installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction

as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85% ,Operating voltage AC 140-270

Volt, freq 50/60 hz, Operating temp range -15 deg to 40 deg centigrade, internal surge protection of 2.5 KV with Short & Open

circuit protection ,THD < 10% , P. F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be below 5 %), life time (LED,Driver &

electrical circuitary), of minimum 50000 Burning Hours with , 70% of initial Lumen maintained till life ends, CCT

3000°K / 4000°K / 5700°K /6000°K/6500°K (As per ANSI Bin), SDCM(Standard Deviation Color Matching) <3, Maximum

power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard and trade mark

certificate ( T.C.). Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect

i/c connections with 1.5 sq mm FRLS, PVC insulated copper conductor single core cable and earthing etc. as required with

Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80 Test report from NABL

lab for all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by

Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminum housing such that LED junction

temperature shall not rise above 90°C).

Powder coated die cast / Extruded aluminium Body (Thickness ≥ 1.20 mm) 36 watt

Supplying, installation, Testing & Commissioning of Street light LED fixture powder coated pressure die cast aluminum

body with driver as per the requirement with Driver efficiency >85%, Input voltage: 140-270 Volt AC, freq 50/60 hz, Operating

temp range -15 deg to 50 deg centigrade, External Surge Protection of 10 kv , internal surge protection of 5 KV L,N,E as per

IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2 , P. F.≥0.95, IP 66,IK-8, CRI >70, under

voltage and over voltage protection, EMI EMC As per CISPR -15, lenses for beam angle as per IESNA type I/II/III as per the

width of the road and the project requirement., suitable to fit in up to

65mm dia pipe, life time (LED,Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen

23 NSEE-09 maintained till life ends as per LM80 extrapolation IES TM-21-11 report, CCT 3000°K / 4000°K / 5700°K /6000°K/6500°K Each 15.00 6500.00 97500.00 97500.00

(As per ANSI Bin),SDCM(Standard Deviation Color Matching) <5, Maximum power consumption should not more than the

specified rating and Fixture shall be of relevant BIS standard complete in all respect i/c connections with 1.5 sq mm FRLS,

PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System

lumen efficacy ≥105 <125 lm/Watt output . LM79 & LM80 Test report from NABL lab for all testing required for LED

fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement.

(Thermal management: heat sink of aluminum housing such that LED junction temperature shall not rise above 90°C). The

Fitting should have isolated Driver. 180 watt

Supply installation testing and commissioning of Aero Dynamic Designed Silent Ceiling Fan with Voltage Range 90 V to 300 V,Min.

Air Delivery 212 CMM,,Rust-Proof ABS Blades ,including wiring the down rods of standard length(Upto 45 cm)with 1.5 sq.mm FR

PVC insulated,copper conductor,single core cable including providing and fixing phenolic laminated sheet cover on the Fan Box etc

as Required. 1200 MM

Supply installation testing and commissioning of IP:20 Aluminium Decorative Mirror Light 10W-12 W +- 1 W LED Surface

Mounted 2 ft. with system lumen efficacy of 100 lm/W and P.F >0.9 THD <20% CCT 6500K,CRI 80 .The LED should have life of

50000 Burning Hours at L70.The input voltage shall be 150 V to 270 V.The fixture should have inbuit surge protection of

2KV.Certification-LM 79 and LM 80.The test report should be from Govt. Approved Lab/inhouse NABL Lab.

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Supply installation testing and commissioning of IP65 led Bulk head 10 W +/- 1 W LED Surface Pressure Die Cast Aluminum

system lumen efficacy of 100 lm/W with Polycarbonate Opal Diffuer and P.F.>0.95 ,THD<10% ,CCT 5700K, CRI 80, IK rating

26 NSEE-12 IK08. The LED with Useful life of 50000 Hrs at L70. The Input voltage range shall be 150V to 265V. The Fixture should have In- Each 12.00 1778.00 21336.00 21336.00

built Surge Protection of 2.5kV Certification:- LM79 & LM80 test report should be from govt approved Inhouse NABL lab/

government of India authorised lab .

Online UPS- Input supply: Three Phase, Output supply: Three Phase 0.00 0.00

Supplying, installation, Testing & Commissioning of of following capacity at full load (Unity Power Factor) at operating temperature

0 to 40 deg C, Relative humidity 0 to 95%, Online double conversion true sine wave Uninterrupted hot swappable (allow for the

replacement or addition of battery modules without shutting down the entire system) modular Power Supply (UPS) system with N+1

modules (N denotes total number of moduels requird for rated capacity). The UPS shall include a Rectifier, inverter, battery bank

suitable for 30 minutes back up (Battery VAH capacity shall not be less than 1600 VAH per KVA of UPS rating per Hour backup

time) on full load (Battery shall be VRLA, SMF in ABS Container) and Static Bypass switch alongwith provision for manual bypass,

suitable isolation transformer for additional protection against neutral faults etc. UPS shall have inbuilt phase sequence correction.

The UPS systems offered are to be of the latest technology with Digital Control Microprocessor based for reliable operation using

Insulated Gate Bipolar Transistor (IGBT)'s both for the rectifier & inverter (3 Level) with PWM (Pulse Width Modulation). The

quality of design, manufacturing and inspection process should confirm to the relevant International standards such as IEC/EN/VDE.

The operating efficiency of the UPS systems shall be >96% while operating on battery mode and delivering quality power to the

100% non-linear loads. Current total harmonic effect(ITHD) on the input grid shall be < 5% at 50 %load. (The required LC (

inductor (L) and a capacitor (C)) filters shall be included in UPS cost), extreme power factor kit to be included to limit the input

power factor (PF) to 0.99 and output power factor shall be unity (i.e. kw rating of the UPS shall be kva rating x 1 ), however UPS

27 NSEE-13 shall be suitable to take load at 0.7 laging to 0.7 leading power factor loads. UPS shall be suitable for incoming supply AC : 3Phase 0.00 0.00

400V +/-20%, 50 Hz +/-5 Hz, AC Output voltage: 3Phase 415 Volt, 50 Hz +/- 0.2Hz, Overload capacity of 120% for 10 mins, Sine

wave output. Non condensing, noise level less than 60db at 1 meter distance, protections: Input Under voltage over voltage,

abnormal out voltage, battery over charging, output over current, short circuit protection, battery deep

discharge protection, 10KV surge. UPS must comply with low voltage

electromagnetic compatibility (EMC) achieved as per EN 6204, EN6204 Part

I and Part 2, it shall be a Voltage and Frequency Independent (VFI)-type

UPS. Communication RS232/RS485/SNMP port open protocol for BMS

integration, all hardware & software for iOT Communication as per approved

by Engineering in charge. Required battery racks and interconnecting

copper conductor cables of suitable size and connectors and all required

accoseries are inclusive of the cost). This system must provide a means for

logging and alarming of all monitored points plus email notification. Forced

air-cooling with integral inbuilt fans with redundancy (if one fan fail UPS

should be able to handle at least 80% of the load, Noise Level 65 DB at 1

d) Battery: Voltage, Capacity. e) Load: KVA, KW, Percentage.

f)Temperature: STS, Inverter, PFC. g) Event Logging & Statistical Data (On

LCD/LED): UPS should capture and display up to 3000 events like: Over

temperature / DC Bus Fail / Fan Fail / Fuse Fail / Overload / Short-circuit /

Device Fail / Inverter Fail / Rectifier Fail / Bypass Fail, etc. h) Statistical Data:

No. of power failures / Transfers to Bypass / Total Running time, etc. i) Mains

Mode of Operation /Battery Mode of Operation / Bypass feeding the load /

UPS Fault /Battery charging and discharging, overload, battery voltage and

battery capacity. j) Audible Alarms : Mains Failure, Battery Low Alarm, UPS

Overload, Fault, Shutdown, Input Over, Under Voltage, Output Over, Under

Voltage, Battery Over, Under Voltage, Over Load and short circuit, Over

Temperature. The UPS should have QR code which should contain

drawing, test report OEM manual,Geo- Tag of manufacturing location etc.

40KVA (Each Power module shall be < 10 KVA)

Supplying, installation of Ceiling Hang-2 100-200W Designed Direct and Indirect Multiglass Chandelier having minimum system

lumenof 4500 lm & the luminaire shall be with system efficacy # 90 lm / W. Housing: Pressure Die Cast Aluminium. IP20 ,

Optics:PMMA/Polysterene Diffuser. The operating CCT shall be 3000K with CRI of #90. The luminaire shall be with BIS Registered

28 NSEE-15 electronicdriver with input voltage range of 90 to 265V , THD # 10% & PF # 0.9, 50,000 Hrs LED Life with L70 Criteria. The LED Each 1.00 575000.00 575000.00 575000.00

Driver shall be easily avaiable in India for repair and service. The LED shall be SMD type. Luminaire shall have minimum surge

protection of 2KV.Theluminaire shall be with following certifications: LM79 & LM80 issued by LED manufacture along with Photo

Biological SafetyStandard.

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Supplying,Installation,Testing and Commissioning of Cubical Indoor Type Transformer Distribution Panel Board Suitable for

415 V 3 Phase 4 Wire 50 HZ AC Supply System including Incomers,Out Goings,Bus Bars,, etc. as required to match the SLD as

per the Following Description.(IP:55).Refer SLD for Details(Near Transformer)

Adj. TMR Based MCCB 800 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (01 Nos)

Adj. TMR Based MCCB 400 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (02 Nos)

Contactor 900 A (01 Nos)

Contactor 560 A (02 Nos)

Digital Metering Devices,comprising Voltmeter,Ammeter,Selector Switch,Indicating Lamps,C.T Set,Bus Bar( 1000 Amps

),Interlockings ,PLC,HMI ,Controller if Required and Other Relays to make it functional as per the Breaker conditions shown in the

Adj. TMR Based MCCB320 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (02 Nos)

Adj. TMR Based MCCB250 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (03 Nos)

Adj. TMR Based MCCB200 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (03 Nos)

Adj. TMR Based MCCB125 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (01 Nos)

Adj. TMR Based MCCB100 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (01 Nos)

Adj. TMR Based MCCB63 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (03 Nos)

Load Bearing Members to be made out of 2.0 mm CRCA Sheet.

Partitions to be made out of 1.6 mm CRCA Sheet

Gland Plates to be 3.0 mm Thick.

Supplying,Installation,Testing and Commissioning of Cubical Indoor Type Automatic Power Factor Correction Panel Board

Suitable for 415 V 3 Phase 4 Wire 50 HZ AC Supply System including Incomers,Out Goings,Bus Bars,, etc. as required to match

the SLD as per the Following Description.(IP:55).Refer SLD for Details(Near Transformer)

Adj. TMR Based MCCB 250 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (01 Nos)

Digital Metering Devices,comprising Voltmeter,Ammeter,Selector Switch,Indicating Lamps,C.T Set,Bus Bar( 300 Amps ) and

Other Relays and Accessories to make it functional as per the Breaker conditions shown in the SLD.

Adj. TMR Based MCCB 16 Amps TP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (03 Nos)

Contactor 5 Kvar Capacitor Duty 440 Volts 3 Phase Conforming to IS / IEC 60947-4-1 & IEC 60947-4-1(03 Nos)

Adj. TMR Based MCCB 25 Amps TP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (01 Nos)

30 NSEE-17 Contactor 12.5 Kvar Capacitor Duty 440 Volts 3 Phase Conforming to IS / IEC 60947-4-1 & IEC 60947-4-1(01 Nos) Set 1.00 554347.73 554347.73 554347.73

Adj. TMR Based MCCB 50 Amps TP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (02 Nos)

Contactor 25 KVar Capacitor Duty 440 Volts 3 Phase Conforming to IS / IEC 60947-4-1 & IEC 60947-4-1(02 Nos)

Adj. TMR Based MCCB 100 Amps TP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (02 Nos)

Contactor 50 KVar Capacitor Duty 440 Volts 3 Phase Conforming to IS / IEC 60947-4-1 & IEC 60947-4-1(02 Nos)

Capacitor 5 Kvar ,440 Volts(03 Nos)

Capacitor 10 Kvar ,440 Volts(01 Nos)

Capacitor 25 Kvar ,440 Volts(02 Nos)

Capacitor 50 Kvar ,440 Volts(02 Nos)

Load Bearing Members to be made out of 2.0 mm CRCA Sheet.

Partitions to be made out of 1.6 mm CRCA Sheet

Gland Plates to be 3.0 mm Thick.

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Supplying,Installation,Testing and Commissioning of Cubical Indoor Type Building Distribution Panel Board Suitable for 415 V 3

Phase 4 Wire 50 HZ AC Supply System including Incomers,Out Goings,Bus Bars,, etc. as required to match the SLD as per the

Following Description.(IP:42).Refer SLD for Details(For Main Building)

Adj. TMR Based MCCB 320 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (01 Nos)

Digital Metering Devices,comprising Voltmeter,Ammeter,Selector Switch,Indicating Lamps,C.T Set,Bus Bar( 400 Amps ) and MCB

Strip of suitable size as Required.

Adj. TMR Based MCCB 100 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (06 Nos)

Adj. TMR Based MCCB 63 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (04 Nos)

MCB 25 A F.P 10 Ka"C" Curve(03Nos)

MCB 63 A F.P 10 Ka"C" Curve(02 Nos)

Load Bearing Members to be made out of 2.0 mm CRCA Sheet.

Partitions to be made out of 1.6 mm CRCA Sheet

Gland Plates to be 3.0 mm Thick.

Supplying,Installation,Testing and Commissioning of Cubical Indoor Type General Distribution Panel Board -1/2/3 Suitable for

415 V 3 Phase 4 Wire 50 HZ AC Supply System including Incomers,Out Goings,Bus Bars,, etc. as required to match the SLD as

per the Following Description.(IP:42).Refer SLD for Details(First Floor)

Adj. TMR Based MCCB 100 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (01 Nos)

Digital Metering Devices,comprising Voltmeter,Ammeter,Selector Switch,Indicating Lamps,C.T Set,Bus Bar( 150 Amps ) and MCB

32 NSEE-19 Strip of suitable size as Required. Set 3.00 160725.69 482177.06 482177.06

MCB 25 A F.P 10 Ka"C" Curve(05Nos)

MCB 63 A F.P 10 Ka"C" Curve(03 Nos)

Load Bearing Members to be made out of 2.0 mm CRCA Sheet.

Partitions to be made out of 1.6 mm CRCA Sheet

Gland Plates to be 3.0 mm Thick.

Supplying,Installation,Testing and Commissioning of Cubical Indoor Type UPS Distribution Panel BoardSuitable for 415 V 3

Phase 4 Wire 50 HZ AC Supply System including Incomers,Out Goings,Bus Bars,, etc. as required to match the SLD as per the

Following Description.(IP:42).Refer SLD for Details(Ground Floor)

Adj. TMR Based MCCB 100 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (03 Nos)

Digital Metering Devices,comprising Voltmeter,Ammeter,Selector Switch,Indicating Lamps,C.T Set,Bus Bar( 200 Amps ) and MCB

33 NSEE-20 Strip of suitable size as Required. Set 1.00 253632.24 253632.24 253632.24

MCB 32 A F.P 10 Ka"C" Curve(10Nos)

MCB 25 A F.P 10 Ka"C" Curve(09Nos)

Load Bearing Members to be made out of 2.0 mm CRCA Sheet.

Partitions to be made out of 1.6 mm CRCA Sheet

Gland Plates to be 3.0 mm Thick.

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Supplying,Installation,Testing and Commissioning of Cubical Indoor Type HVAC Distribution Panel Board -1/2 Suitable for 415

V 3 Phase 4 Wire 50 HZ AC Supply System including Incomers,Out Goings,Bus Bars,, etc. as required to match the SLD as per

the Following Description.(IP:55).Refer SLD for Details(Near HVAC Outdoor Machines)

Adj. TMR Based MCCB 200 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (01 Nos)

Power Contactor 325 A F.P AC-1 Duty 415 Volts (01 Nos)

Surge Protection Device Type I+II 50 KA 3P+N(01 Nos)

34 NSEE-21 Single Phase Preventer(01 Nos) Set 2.00 576996.71 1153993.43 1153993.43

Digital Metering Devices,comprising Voltmeter,Ammeter,Selector Switch,Indicating Lamps,C.T Set,Bus Bar( 300 Amps ) and MCB

Strip of suitable size as Required.

Adj. TMR Based MCCB 63 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (08 Nos)

Load Bearing Members to be made out of 2.0 mm CRCA Sheet.

Partitions to be made out of 1.6 mm CRCA Sheet

Gland Plates to be 3.0 mm Thick.

Supplying,Installation,Testing and Commissioning of Cubical Indoor Type External Service and Street Light Panel Board

Suitable for 415 V 3 Phase 4 Wire 50 HZ AC Supply System including Incomers,Out Goings,Bus Bars,, etc. as required to match

the SLD as per the Following Description.(IP:55).Refer SLD for Details(Near Security Room)

Adj. TMR Based MCCB 100 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (01 Nos)

Digital Metering Devices,comprising Voltmeter,Ammeter,Selector Switch,Indicating Lamps,C.T Set,Bus Bar( 200 Amps ) and MCB

35 NSEE-22 Strip of suitable size as Required. Set 1.00 379598.62 379598.62 379598.62

Adj. TMR Based MCCB 40 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (09 Nos)

MCB 40 A D.P "C" Curve 10 Ka(02 Nos)

Load Bearing Members to be made out of 2.0 mm CRCA Sheet.

Partitions to be made out of 1.6 mm CRCA Sheet

Gland Plates to be 3.0 mm Thick.

Supplying,Installation,Testing and Commissioning of Cubical Indoor Type AMF Panel Board for Residential Accomodation

Suitable for 415 V 3 Phase 4 Wire 50 HZ AC Supply System including Incomers,Out Goings,Bus Bars,, etc. as required to match

the SLD as per the Following Description.(IP:55).Refer SLD for Details(Near 82.5 Kva D.G Set)

Adj. TMR Based MCCB 160 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (02 Nos)

Power Contactor 160 A F.P AC-1 Duty 415 Volts (02 Nos)

AMF Controller and Necessary relays for AMF Operation(01 Set)

36 NSEE-23 Digital Metering Devices,comprising Voltmeter,Ammeter,Selector Switch,Indicating Lamps,C.T Set,Bus Bar( 200 Amps ) and MCB Set 1.00 573513.32 573513.32 573513.32

Strip of suitable size as Required.

Adj. TMR Based MCCB 63 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (06 Nos)

Adj. TMR Based MCCB 100 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (02 Nos)

Load Bearing Members to be made out of 2.0 mm CRCA Sheet.

Partitions to be made out of 1.6 mm CRCA Sheet

Gland Plates to be 3.0 mm Thick.

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Supplying,Installation,Testing and Commissioning of Cubical Indoor Type Type -2 Residential Building Distribution Panel

Suitable for 415 V 3 Phase 4 Wire 50 HZ AC Supply System including Incomers,Out Goings,Bus Bars,, etc. as required to match

the SLD as per the Following Description.(IP:55).Refer SLD for Details

Adj. TMR Based MCCB 100 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (01 Nos)

Digital Metering Devices,comprising Voltmeter,Ammeter,Selector Switch,Indicating Lamps,C.T Set,Bus Bar( 150 Amps ) and MCB

37 NSEE-24 Strip of suitable size as Required. Set 1.00 155939.29 155939.29 155939.29

MCB 63 A D.P "C" Curve 10 Ka(03 Nos)

MCB 16 A D.P "C" Curve 10 Ka(02 Nos)

Load Bearing Members to be made out of 2.0 mm CRCA Sheet.

Partitions to be made out of 1.6 mm CRCA Sheet

Gland Plates to be 3.0 mm Thick.

Supplying,Installation,Testing and Commissioning of Cubical Indoor Type Type -5 Residential Building Distribution Panel

Suitable for 415 V 3 Phase 4 Wire 50 HZ AC Supply System including Incomers,Out Goings,Bus Bars,, etc. as required to match

the SLD as per the Following Description.(IP:55).Refer SLD for Details

Adj. TMR Based MCCB 100 Amps FP Icu=Ics=100% Breaking Capacity 36 KA with Extendable ROH (01 Nos)

Digital Metering Devices,comprising Voltmeter,Ammeter,Selector Switch,Indicating Lamps,C.T Set,Bus Bar( 100 Amps ) and MCB

38 NSEE-25 Strip of suitable size as Required. Set 1.00 144943.93 144943.93 144943.93

MCB 63 A F.P "C" Curve 10 Ka(04 Nos)

MCB 16 A D.P "C" Curve 10 Ka(01 Nos)

Load Bearing Members to be made out of 2.0 mm CRCA Sheet.

Partitions to be made out of 1.6 mm CRCA Sheet

Gland Plates to be 3.0 mm Thick.

Supplying and Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct

39 NSEE-26 in groundin Existing DWC Pipe including excavation, sand cushioning, protective covering and refilling the trench etc as required. 0.00 0.00

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the

existing surface/ recessed steel/ PVC conduit as required.

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper

braid and protected with PVC sheath in the existing surface/ recessed steel/ PVC conduit as required.

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as

Supplying and drawing of UTP 4 pair CAT 6A LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required. 1 run of

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but

excluding modular plate etc. as required.

a 1.24.6 Telephone socket outlet Nos 54.00 168.00 9072.00 9072.00

b N.S Computer Socket RJ45 Modular type Nos 140.00 443.00 62020.00 62020.00

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Supplying and Installing Following Size of Perforated Hot Dipped Galvanized Cable Tray with Perforation not more than 17.5% in

convenient Sections ,joined with connectors ,suspended from the Ceiling with medium duty internally threaded utility anchors HUS3

I 6 of HILTI make or Equivalent for fixing of HVAC ducts/pipe supports/ cable tray supports and other overhead service utilities.

The anchor should be cold formed carbon steel Galvanised/A4-Stainless steel.The screw must possess ETA Certificate for use in both

Cracked Concrete and non-cracked concrete, approved as per Seismic C1 Category. The anchor should be tested for use in hollow

core slabs. Design of Anchor should be done as per EC2 Part-4 using Engineering Software as per actual load data and site

conditions as provided by structural consultant and the report to be submitted to the project manager and design engineer for

approval.The installation should be done using Impact Wrench driver and the setting instructions should be strictly followed as per

the manufacturers recommendations and painting with two or more coats of synthetic enamel paint of required shade complete as

a 4.6.4 300 mm width X 50 mm depth X 1.6 mm thickness Rmt 324.00 1062.00 344088.00 344088.00

b 4.6.7 600 mm width X 50 mm depth X 2.0 mm thickness Rmt 120.00 1925.00 231000.00 231000.00

c 4.6.3 225 mm width X 50 mm depth X 1.6 mm thickness Rmt 60.00 991.00 59460.00 59460.00

d 4.6.1 100 mm width X 50 mm depth X 1.6 mm thickness Rmt 144.00 754.00 108576.00 108576.00

Supply and Making end Termination with Brass Compression Gland and Aluminium Lugs for the Following Sizes of PVC insulated

and PVC Sheathed/XLPE Aluminium Conductor Cable of 1.1 KV Grade as Required (Comet)

Supplying and laying of following size DWC HDPE pipe ISI marked along with all accessories like socket, bend, couplers etc.

47 15.16 conforming to IS 14930, Part II complete with fitting and cutting, jointing etc.direct in ground (75 cm below ground level) including 0.00 0.00

excavation and refilling the trench but excluding sand cushioning and protective covering etc., complete as required.

Supply,Installation,Testing and Commissioning of 2.2 KVA Sine Wave Inverter , Input 1 Phase 3 wire and output 1 phase 3 wire

with 2 Nos of 12 V 200 aH Battery.

49 NSEE-29 Providing of following size of Under Floor Trunking (Make: Legrand) of following items including accessories as required. 0.00 0.00

a A M Track 300 mm x 38 mm x 1.6 mm- 3 compartment Rmt 96.00 3970.00 381120.00 381120.00

b B Junction Box Top recess-8mm with Metallic Lid,Height 55-70 mm(350 x 350 mm) Each 7.00 6642.00 46494.00 46494.00

50 NSEE-30 Supply and Fixing of Desking Module 8M Each 25.00 10509.00 262725.00 262725.00

Supply & Erection of lockable 12 U rack with 5A strip and two fan for distribution, mounting of patch panels, hubs,

switches etc,, complete as per specification and as desired by EIC.

Supply, installation, testing and commissioning of Junction Boxes/DB-10 Pairs with Original Krone module and Back Mount Frame

and have Lock -n- key, complete in all respect as per specification and desired by EIC

Supply, installation, testing and commissioning of Junction Boxes/DB-20 Pairs with Original Krone module and Back Mount Frame

and have Lock -n- key, complete in all respect as per specification and desired by EIC

Supply, installation, testing and commissioning of Junction Boxes/DB-30 Pairs with Original Krone module and Back Mount Frame

and have Lock -n- key, complete in all respect as per specification and desired by EIC

SITC of 20 Pair armoured Telephone cable. {0.5mm.Dia (Minimum)}

Supplying,Installation,Testing and Commissioning of 55 Inches Full H.D LED Display Monitor as per the Specifications attached.

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Supply, Installation, Testing & Commissioning of 5MP IP Network TDN Low-Light IR Fixed Lens Dome Camera, 1/2.7" CMOS or

better, 5MP (2880 x 1620) @ 25fps or better, triple stream at various resolution & Frame Rates, Min. Illumination required 0.007 lux

(color), 0 Lux IR On, 2 IR LEDs, Smart IR with upto 30m IR distance, Auto ICR (Infrared Cut Filter) 120dB True WDR, S/N Ratio

50db, Shutter Speed 1/2-1/100000S,Adavance Video Compression technology such as H.265, H.264 & MJPEG , Fixed Lens 2.8mm,

57 NSEE-37 Field of View FoV H:90°, V:50°, BLC, HLC, WDR, 3DNR, White Balance - Auto/Manual, Minimum Edge Intelligence Video Nos 35.00 14510.00 507850.00 507850.00

Analytics, 4 Privacy Mask, 8 Region Of Intreset, Defog, HTTPS, IP Filter, TLS1.2, AES-128/256, SSH/Telnet closed, Stream

Encryption, 2-Way Audio Full Duplex Line IN/Out, 256GB SD card support, Alarm: 1In/1out, PoE (802.3 af) and 12V DC, Max

5W, IP 66/67 & IK10 with Die Cast Aluminium Housing, Having Operating temp range : –40°C to 60° C. Certifications: ONVIF

Profile S/G/T Compliant, CE, FCC, EN, RoHS & NDAA Section 889 compliant.

Supply , Installation , Testing and commissioning of 32 Channel NVR (Network Video Recorder) Embedded Linux based for

recording upto 32CH at D1 960fps with 04 nos. SATA HDDs minimum 40TB storage or more (recording requirement all cameras

recording at D1, 25fps for 30 days), H.265 HEVC/H.264/MJPEG codec decoding, Front Panel with LEDs Indication for Power &

HDDs Status, 3 nos. USB, ONVIF S, Time Sync with NTP, Encrypted Streaming & Control, 2-Way Audio Line & Out, PTZ

Operation Pan, Tilt, Zoom, Support, Pre & Post Alarm Recording Support, Recording/Evidence Clip Export to USB, 16 Channel

58 NSEE-38 Synchronous Playback, Playback control i.e Play, Pause, Stop, Fast Forward, Backward, Speed Control, Timeline & Zoom; Each 2.00 81442.00 162884.00 162884.00

Snapshot, Web Client, Central Monitoring Software, iPhone; iPad; Android based Mobile clients, 02HDMI & 01VGA Output, 04 On

Board HDDS each up to 10TB, Alarm Input (06 nos.), Alarm Output (02 nos.), 196 Mbps throughput, NDAA Section 889

Compliant, Operating Temperature –10°C to 55°C, Certification : Certifications: ONVIF compliant, UL/CSA 62368-1, CE (EN

50130-4), FCC Part 15, EN 55032, NDAA & RoHS (EN63000) compliant. Including fixing accessories and cable termination with

required connectors/Jack, complete in all respect as per instruction of engineer in-charge.

59 NSEE-39 SITC of 6TB 7200 rpm SATA 6 Gb/s 3.5" Internal Enterprise Hard Drive Each 4.00 17000.00 68000.00 68000.00

60 NSEE-40 Supplying and Laying of 20 Mtr HDMI Optical Fiber Cable AOC 2.0, 4K with Bandwidth 18Gbps Each 1.00 6795.00 6795.00 6795.00

61 NSEE-41 Supplying and Fixing of S.D Card 256 G.B in the Existing Camera Each 35.00 2844.00 99540.00 99540.00

SITC of Patch Cord Category 6 4-Pair, F/UTP, Horizontal cable, 23 AWG solid bare copper conductors WITH RJ45 CONNECTOR

AT BOTH END 1 MTR LENGTH.

SITC of Patch Cord Category 6 4-Pair, F/UTP, Horizontal cable, 23 AWG solid bare copper conductors WITH RJ45 CONNECTOR

AT BOTH END 2 MTR LENGTH.

SITC of CAT 6 F/UTP 16 Port Modular fully loaded patch Panel TIA/EIA-568-C.2:2009 EN 50173- 1:2011 Class E,

ISO/IEC11801:2010 (Ed 2.2) Class E, FCC Subpart F68.5 UL Listed.

SITC of CAT 6 F/UTP 24 Port Modular fully loaded patch Panel TIA/EIA-568-C.2:2009 EN 50173- 1:2011 Class E,

ISO/IEC11801:2010 (Ed 2.2) Class E, FCC Subpart F68.5 UL Listed.

Supply, Installation, Testing and Commissioning of Layer 2, PoE enabled, with PD: minimum 370 Watt (should have minimum 15.4

Watt per Port), fully managed, 1RU, GE Switch to be operated on 200-240VAC, 50 Hz Supply, with perpetual license of

OEM,having minimum technical specification:

a) 16 x 10/100/1000Base-T Mbps PoE+ enabled host ports (Minimum); b) 4 x 10GE SFP+ port; c) Forwarding performance/stacking

bandwidth/ backplane speed (Minimum) of 95.2Mpps; d) Fanless operation with operating temperature up to 50°C; e) DRAM and

Flash RAM as per OEM; f) Software support with IPv4 routing (542 routes), multicast routing (IGMP) including necessary software

license; g) Minimum switching capacity of 216Gbps; h) Number of VLAN Supported: 64 (Minimum).; i) Total number of MAC

Address: 8,000 (Minimum); j) Minimum Security: User privilege management and password protection, DoS attack defense, ARP

attack defense, and ICMP attack defense, Binding of the IP address, MAC address, interface, and VLAN, Port isolation, port

security, and sticky MAC, MFF, Blackhole MAC address entries, Limit on the number of learned MAC addresses, 802.1x

authentication and limit on the number of users on an interface, AAA authentication, RADIUS

authentication, HWTACACS authentication, and NAC, SSH v2.0, Hypertext Transfer Protocol Secure (HTTPS), CPU defense, l; l)

REGULATORY: RoHS, WEEE, IEC 61000-4-2:2008, CISPR Class, ICES-003 Class A,UL,CSA 22.2,FCC,EN 300 386, CCC,

ICES -003, CB. The OEM should have 24x7 TAC support center with India toll free number reflected in official website.Make:

Cisco, Juniper, Extreme/Netgear/Allied Telesis

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Supply, Installation, Testing and Commissioning of Layer 2, PoE enabled, with PD: minimum 370 Watt (should have minimum 15.4

Watt per Port), fully managed, 1RU, GE Switch to be operated on 200-240VAC, 50 Hz Supply, with perpetual license of

OEM,having minimum technical specification:

a) 24 x 10/100/1000Base-T Mbps PoE+ enabled host ports (Minimum); b) 4 x 10GE SFP+ port; c) Forwarding performance/stacking

bandwidth/ backplane speed (Minimum) of 95.2Mpps; d) Fanless operation with operating temperature up to 50°C; e) DRAM and

Flash RAM as per OEM; f) Software support with IPv4 routing (542 routes), multicast routing (IGMP) including necessary software

license; g) Minimum switching capacity of 216Gbps; h) Number of VLAN Supported: 64 (Minimum).; i) Total number of MAC

67 NSEE-47 Address: 8,000 (Minimum); j) Minimum Security: User privilege management and password protection, DoS attack defense, ARP Each 3.00 74653.00 223959.00 223959.00

attack defense, and ICMP attack defense, Binding of the IP address, MAC address, interface, and VLAN, Port isolation, port

security, and sticky MAC, MFF, Blackhole MAC address entries, Limit on the number of learned MAC addresses, 802.1x

authentication and limit on the number of users on an interface, AAA authentication, RADIUS authentication, HWTACACS

authentication, and NAC, SSH v2.0, Hypertext Transfer Protocol Secure (HTTPS), CPU defense, l; l) REGULATORY: RoHS,

WEEE, IEC 61000-4-2:2008, CISPR Class, ICES-003 Class A,UL,CSA 22.2,FCC,EN 300 386, CCC, ICES -003, CB. The OEM

should have 24x7 TAC support center with India toll free number reflected in official website.Make: Cisco, Juniper,

Extreme/Netgear/Allied Telesis

68 NSEE-48 Supply,Installation,Testing and Commissioning of Media Converter. Nos 10.00 5335.00 53350.00 53350.00

69 NSEE-49 Supply & Erection of Termination Box complete as per specification and as desired by EIC. Nos 10.00 3642.00 36420.00 36420.00

70 NSEE-50 Supplying,Installation,Testing of 12 Core Optical Fibre Cable Single Mode. Rmt 120.00 135.00 16200.00 16200.00

SITC of stackable, Layer 3 fully managed, 1RU Switch to be operated on 200-240VAC, 50 Hz

Supply, having minimum technical specification :

a) 24 x 10/100/1000 Base-T host ports (Minimum).

b) 4 x 1G/10G SFP+ ports and field replaceable SFP module of same rating

c) 40 Gbps stacking bandwidth (Minimum).

d) Minimum switching capacity of 128 Gbps

e) Total number of MAC Address: 16,000 (Minimum).

f) Number of VLAN Supported: 4000 (Minimum).

g) Routing Protocol: Static, RIPng, OSPFv3,BGP4, VRRP and Policy based routing

h) Dual internal power supplies

i) IGMP Snooping v1,v2,v3, MLD Snooping v1,v2, PIM-SM for IPv4 and IPv6

j) Operating temperature – upto 45°C.

k) Minimum Security features e.g. DHCP Snooping, Dynamic ARP Inspection, BPDU Protection,

RADIUS, TACACS+, IP Source Guard, ACL based on L2,L3,L4 and physical port, MAC limiting

(per port and per VLAN), Authentication based on MAC,WEB and 802.1x, Control Plane

Protection (CoPP), IPv6 RA Guard,IPv6 neighbour discovery, Multi-domain authentication etc. l)

Link recovery 50 msec.

l ( IEEE 802.1Q, .1D, IEEE 802.3ab, 3ad, 3az, 3ah, IEEE 802.1p, af, at, 1w, 1s,1d, IEEE 802.1X,

72 NSEE-52 Supply,installation with foundation as per approved Drawing 9 Mtr. Long Pole,ST-410 SP33) Nos 5.00 14737.00 73685.00 73685.00

73 NSEE-53 Supply,Installation and Commissioning of 11 KV Air Break Switch(200 Amps). Set 2.00 7840.00 15680.00 15680.00

74 NSEE-54 Supply,Installation of 11 KV L.A 10 ka (Station Class). Set 2.00 5600.00 11200.00 11200.00

75 NSEE-56 Supply,Installation of 11 KV HG Fuse Unit . Set 2.00 5315.00 10630.00 10630.00

76 NSEE-57 Supply,Installation of Disc Insulator(B&S)70 KN suitable for 100 sq.mm Triple AAAC. Nos 7.00 455.00 3185.00 3185.00

77 NSEE-58 Supply and Installation of 100 Sq.mm AAAC Triple AAAC. Kgs 120.00 224.00 26880.00 26880.00

Supply,Installation of 11kV Polymeric composite Pin Insulator 12kV, 5kN, Lighting Impulse 75kV Positive and 80kV

Negative,creepage distance 320mm

79 NSEE-60 Supply and Erection of 150 mm Dia. Heavy Class G.I Pipe for the Cable Protection. Rmt 7.20 896.00 6451.20 6451.20

80 NSEE-61 Supply and Installation of Anti Climbing Device Kgs 4.80 118.00 566.40 566.40

Galvanised Stay Set with 50x8mm stay clamp, guy insulator(2Nos.), anchor plate (200x 200 x 6 mm),nut-bolts, 2 Nos turn-buckles,

1.8m long, 16 mm diameter solid GS stay rod & 7/3.15 mm dia GI stranded wire complete

11/0.433 KV, 3 Phase, 50 Hz Outdoor mounting 0.00 0.00

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Supply, installation, testing and commissioning of following capacity (continuous loading) 11/0.433 KV Delta/Star, step down, 3

Phase, 50 Hz, Dyn 11 vector group, Cast Resin / VPI (vacuum pressure impregnated) Dry Type, copper wound transformer

(Electrolytic grade 99.9% pure copper, Core made of first grade Cold Rolled Grain Oriented (CRGO) Core grade MOH or better)

AN (air natural) cooled transformer suitable for Outdoor applications with enclosure, On Load Tap Changer (OLTC) on HV side

having AVS relay and Remote Tap Changer Control (RTCC) for automatic sensing of incoming voltage, automatic operation of

OLTC and facility for remote/ manual operation of OLTC HV side in range of +5% to -15% in steps of 2.5%, insulation class F

(minimum), suitable for environment conditions Class E-O-3, suitable for fire behavior class F1,climate class-C1, having cable end

boxes on HV side suitable for 3x300 sqmm XLPE cable of 11 KV grade with necessary hardware, clamps, lugs etc. for termination

on HV/MV etc. for all transformers, bus trunking arrangement on LV side complete with all accessories and safety provisions as per

relevant IS Code ,The transformer shall be provided with standard fittings/accessories as per relevant IS and mentioned below,

protection alarm/trip protection, 3 nos. of Polymeric Zinc Oxide surge Arrestors on HV Side. Winding Temperature scanner

(Digital) with alarm/Trip contacts with RTD Sensors per LV winding and space for mounting differential protection CT's in LV

chamber with neutral brought out separately including supplying and laying of copper conductor multicore control cable from

transformer to HT breaker/HT Panel for safety tripping, complete as confirming to IS-2026 Part-11, i/c supplying and grouting of

82 3.28 suitable M.S. Channel with all accessories ,complete in all respects as required at site as per CPWD specifications. Design ambient 0.00 0.00

condition : a) air temperature 50 deg C, b) Relative Humidity 90 % Max, c) Seismic Zone as per location of site, d) Altitude as per

location/site. The transformer should have QR code which should contain drawing, test report OEM manual, Geo- Tag of

manufacturing location, rating plate as per relevant IS Code etc. All testing shall as per relevant IS Code. Noise level Shall not exceed

limits as per NEMA TR-1 with all accessories running

measured as per IEC 551 / NEMA standard. The enclosure shall also have Welded Door handle , Danger plate on HV and LV side

doors, caution plate for tap links for HT doors, Door limit switch on both HV and LV side doors to be wired up to WTI box terminal

for tripping the transformer in case door is opened with then closure transformer energized, Phase marking plates on HV and LV

doors. Fitting and Accessories : The following fittings shall be provided:- a) Two earthing terminals with the earthing symbol b)

Rating and terminal marking plates; c) Thermometer pocket with cap; d) Lifting lugs for the complete transformer as well as for core

and winding assembly; e) Bi-directional flat rollers (for transformers above 200 kVA); f) HV side neutral grounding strip (where one

of the HV bushing terminal is connected to earth); g) Arcing horns or suitable rating lightning arrestors for HT side – 3 Nos. for

transformers up to 200 kVA; h) Bird guard; i) Jacking pads (for transformer above 1 600 kVA); j) Name Rating & Diagram Plate.

k) Monogram Plate. i) Additional neutral separately brought out on bushing for earthing. Level 3

a 3.28.9 630 KVA (losses at 50% loading < 2000watt, losses at 100% loading < 5855watt) (For Main Building) Each 1.00 1464769.00 1464769.00 1464769.00

b 3.28.2 100 KVA (losses at 50% loading < 520watt, losses at 100% loading < 1800watt)(for Residential Quarters) Each 1.00 232503.00 232503.00 232503.00

84 Nsee-63 Supply,Installation,Testing and Commissioning of Servo Transformer Out door Type with the following Specifications: Set 1.00 2576000.00 2576000.00 2576000.00

Equipment - Servo Voltage Stabilizer

Capacity - 630 KVA

Design & Testing Standards - IS:9815/IS 2026

Winding - Copper

Frequency - 50 Hz

Phase - 3 Phase

TYPE - UNBALANCED TYPE –Suitable for unbalanced input voltage and unbalanced load, Outdoor

Duty Cycle - 100% Continuous

FIRST FILL OF OIL - As per IS:335/1983(Included)

Temp. Rise in Oil - 50 degree C

a NSEE-64 Temp. Rise in Winding - 55 degree C 0.00 0.00

Overload Capacity - 100% for 1 minute

Voltage Display - Voltmeters for input and output

Current Display - Ammeter with CT's & Selector Switch

Operation - Auto/ Manual

WheelL - Unidirectional wheels

Earthing - 2 Earthing terminals

Cable Box & Bus Bar - Suitable size of cable box with 6 bus bars( 3 for input,3 for output & 1 for neutral)

Regulators - Rolling contact type

Protections - Under voltage , over voltage , short circuit, overload protection through suitable capacity MCCB

By Pass Arrangement - Bypass arrangement shall be provided through suitable capacity by pass switch

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Supply, Installation testing and commissioning of indoor type termination kit for 3 C x 120 mm² 11 KV XLPE insulated Aluminum.

conductor PVC outer sheathed armoured HT Cable with Earth (A2XFY with Earth HT Cable).(Raychem make)

Supply, Installation testing and commissioning of outdoor type termination kit for 3 C x 120 mm² 11 KV XLPE insulated

Aluminum. conductor PVC outer sheathed armoured HT Cable with Earth (A2XFY with Earth HT Cable).(Raychem make)

POWER AND CONTROL CABLES :- 0.00 0.00

Supplying and Laying of XLPE Insulated and PVC Sheathed Power Cable of 11KV/ 1.1 KV Grade of the following size direct in

Ground including excavation,sand Cushioning, Protective Covering and Refilling the Trench as Required.

3 C x120 mm² 11 KV XLPE insulated Aluminum. conductor PVC outer sheathed armoured HT Cable with Earth (A2XFY with

Earth HT Cable).

Supply, Installation testing and commissioning of indoor type termination kit for 3 C x 50 mm² 11 KV XLPE insulated Aluminum.

conductor PVC outer sheathed armoured HT Cable with Earth (A2XFY with Earth HT Cable).(Raychem make)

Supply, Installation testing and commissioning of outdoor type termination kit for 3 C x 50 mm² 11 KV XLPE insulated Aluminum.

conductor PVC outer sheathed armoured HT Cable with Earth (A2XFY with Earth HT Cable).(Raychem make)

POWER AND CONTROL CABLES :- 0.00 0.00

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from earth electrode including connection with brass nut,

bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt,

spring, washer excavation and re-filling etc. as required.

Supplying and Laying of XLPE Insulated and PVC Sheathed Power Cable of 11KV/ 1.1 KV Grade of the following size direct in

Ground including excavation,sand Cushioning,Protective Covering and Refilling the Trench as Required.

3 C x50 mm² 11 KV XLPE insulated Aluminum. conductor PVC outer sheathed armoured HT Cable with Earth (A2XFY with Earth

Supplying,Installation,Testing and Commissioning of Copper Earthing Electrode of Size 50 x 3000mm with Copper Pipe Outer Dia.

50 mm (+-) 5 %),Length 3000 mm,Inner & and Outer Strip Size 25X6mm (Copper),Terminal Hole Two Nos.,Terminal Hole Dia. 14

mm,Seal Plate Thickness 4 mm,Base Plate Thickness 4 mm,Inner filling Material – Highly Conductive Super Crystalline

Mixture,Outer filling material - Highly Hygroscopic, Non corrosive Back Fill Compound 50 Kgs.

Supplying,Installation,Testing and Commissioning of G.I Earthing Electrode of Size 50 x 3000mm with GI Pipe Outer Dia. 58 mm

(+-) 5 %,Length 3000 mm,Inner & Outer GI Strip Size 32X6mm,Terminal Hole Two Nos.,Terminal Hole Dia. 14 mm,Seal Plate

Thickness 4 mm,Base Plate Thickness 4 mm,Inner filling Material – Highly Conductive Super Crystalline Mixture,Outer filling

material - Highly Hygroscopic, Non corrosive Back Fill Compound 50 Kgs.

D.G Sets and Allied Works 0.00 0.00

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode

including connection with G.I. thimble excavation and re-filling as required.

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Supply, installation, Testing & Commissioning of 'Silent Type Diesel Generating set as per CPCB IV + or better norms along with

having Prime Power Rating of KVA as below, 415 volts at 1500 RPM, 0.8 lagging power factor at 415 V suitable for 50 Hz, 3 phase

system & for 0.85 Load Factor, including testing at factory and site with fuel, load for test and other necessary arrangements

Complete as per CPWD specifications, should have QR code which should contain drawing, test report OEM manual,Geo-

Tag of manufacturing location, rating plate as per relevant IS Code etc. and consisting of the followings:

(A) Diesel Engine:

Turbocharged Diesel engine 4 stroke water cooled, multi cylinder, dynamically balanced fly wheel, electric start of suitable BHP at

1500 RPM suitable for above output of alternator at 40 Degree C, 50% RH & at 1000 Meter MSL , capable of taking 10% over

loading for one hour after 12 hours of continuous operation. The engine will be with Electronic governor, Dry type Air filter with

service indicator, first filling of engine fuel (after commissioning) lubricating Oil, Coolant and other consumables complete with all

the required accessories, the Electronic governor shall be as per ISO 8528. The engine shall comply to the latest CPCB norms (CPCB

IV + or better) and Conforming to BS 5514, BS 649, IS 10000, IS 10002, IS 13018 and as per CPWD specifications. (B) Engine

mounted Instrument Panel fitted with and having digital display for following:

(i) Start-stop switch with key

96 6.1 (ii) Water temperature indication 0.00 0.00

(iii) Lubrication oil pressure indication

(iv) Lubrication oil temperature indication

(v) Battery charging indication and Voltage indication

(vi) RPM indication

(vii) Over speed indication

(viii) Low lubricantion Oil trip indication

(ix) Engine Running Hours indication

(C) Alternator:

Synchronous alternator rated of appropriate KVA, 415 volts at 1500 RPM, 3 phase 50 Hz, AC supply with 0.8 lagging power factor

at 40 Degree C, 50%

RH & at 1000 Meter MSL. The alternator shall be having Screen Protected Drip Proof (SPDP) enclosure IP23, brushless, continuous

duty, dynamically

Supply installation testing and commissioning of 45 W Post Lantern Lamp Pressure die-cast aluminium housing with specially

designed optics, provide uniform light distribution to redefine outdoors and enhance architectural design with System efficacy of 100

97 NSEE-73 lm/W.L70 life of 50000 Hrs. P.F.>0.95 with THD<10% ,CCT 5700 K,CRI 70,Surge Protection 4 Kv. Input voltage range of 120V Each 20.00 12500.00 250000.00 250000.00

to 300V.Certification:- LM79 & LM80 test report should be from govt approved Inhouse NABL lab/ government of India authorised

98 NSEE-74 SITC of IP: 66/IP:67 PVC Junction Box having the Facility to house 4 way Bakellite strip for connection to the spike light Each 20.00 2800.00 56000.00 56000.00

P/f 7 mtr high hot galvanised octagonal pole, continously tapered (bolt fixing type) in single section made out of 3mm thick sheet

suitable for bracket having top dia 70-75mm and bottom dia 130-150 mm, base plate size 220X220X12 to 240X240X16 mm with

99 NSEE-75 door and locking arrangement complete with minimum 1 mtr long MS/GI street light bracket,bakelite sheet,neutral link, suitable Each 19.00 18600.00 353400.00 353400.00

MCB or any other electrical accessory,suitable foundation bolts of diameter16 to 20 mm,700mm apprx length, "J" type,4 pcs set.

Make : Bajaj/Philips/CG/Surya/BPP.

Erection of metallic pole of following length in cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40mm

nominal size) foundation including excavation and refilling etc. as required

Supply,Installation of 3 Mtr 80 mm G.I Pole made of Galvanised Mild Steel Pipe Duly Painted with Two Coats of Primer and

Aluminium Paint Including the Cost of Foundation

Supply installation testing and commissioning of 60 W High performance LED streetlight Housing made from die-cast aluminium

housing with specially designed optics, provide uniform light distribution to redefine outdoors and enhance architectural design with

102 NSEE-78 System efficacy of 100 lm/W IP:66 .L70 life of 50000 Hrs. P.F.>0.95 with THD<10% ,CCT 5700 K,CRI 70,Surge Protection 4 Kv. Each 19.00 9850.00 187150.00 187150.00

Input voltage range of 120V to 300V.Certification:- LM79 & LM80 test report should be from govt approved Inhouse NABL lab/

government of India authorised lab.

103 NSEE-79 Supplying and Laying of Sheathed 3 C x 2.5 Sq.mm Copper Conductor Multistrand Wire IS:694. Rmt 120.00 180.00 21600.00 21600.00

Supply installation testing and commissioning of 11 WBollard, made of extruded aluminium housing, to redefine landscapes with

better light quality and enhance architectural design. Rated IP65..L70 life of 50000 Hrs. P.F.>0.95 with THD<10% ,CCT 5700

K,CRI 70,Surge Protection 4 Kv. Input voltage range of 120V to 300V.Certification:- LM79 & LM80 test report should be from

govt approved Inhouse NABL lab/ government of India authorised lab.

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

E Fire Detection System 0.00

Supplying, installation, testing and commissioning of micro processor based intelligent addressable main fire alarm panel, central

processing unit with the following loop modules and capable of supporting not less than 240 devices (including detectors) and

minimum 120 detectors per loop and loop length up to 2 km, network communication card, minimum 320 character graphics/ LCD

display with touch screen or other keypad and minimum 4000 events history log in the non volatile memory (EPROM), power supply

unit (230 ± 5% V, 50 hz), 48 hrs back-up with 24 volt sealed maintenance free batteries with automatic charger. The panel shall have

facility to connect printer to printout log and facility to have seamless integration with analog/digital voice evacuation system (which

is part of the schedule of work under SH: PA System) and shall be complete with all accessories . The panel shall be compatible for

IBMS system with open protocol BACnet/ Modbus over IP complete as per specifications.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector (Multicriteria)complete with

mounting base complete as required.

3 28.2.6 Supplying, installation, testing & commisssioning of intelligent addressable programmable sounder complete as required. Each 10.00 2787.00 27870.00 27870.00

4 28.2.7 Supplying, installation, testing & commissioning of fault isolator complete with base as required. Each 9.00 3434.00 30906.00 30906.00

5 28.2.14 Supplying, installation, testing & commissioning of addressable manual call point complete as required. Each 9.00 4063.00 36567.00 36567.00

Supplying & laying of 2x1.5 sqmm fire survival armoured cable, 600/1000V rated with annealed copper conductor having glass mica

6 28.5.1 fire barrier tape covered by an extruded layer of Cross Linkable Ethylene Propylene Rubber (EPR) insulation and LSZH inner Rmt. 1800.00 386.00 694800.00 694800.00

bedding, steel wire armouring & LSZH outer sheath complete as required.

Supplying,Installation,Testing and Commissioning of CO2 Type Fire Extinguisher 4.5 Kg. Capacity ISI Mark(IS:15683)suitable for

'B' and 'C' class fires - inflammable liquids, gaseous fires like L.P.G. and acetylene, and electrical fires

Supplying,Installation,Testing and Commissioning of MAP 90 ABCType Fire Extinguisher 4.0 Kg. Capacity ISI

Mark(IS:15683)suitable for Class A/B/C Type Fires .

E Total Fire detection System (E )= 0.00 1446108.00 94781.62 1540889.62

F HVCA System (F )= 0.00

VRF Outdoor Unit (HEAT PUMP TYPE)

Supplying, Installation, Testing & Commissioning of Modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled

Outdoor units suitable for cooling/heating having 100% hermetically sealed inverter type twin Rotary/Scroll Compressor(s), minimum

two compressors (with individual separate PCB) for above 14HP modules, microprocessor based Controller, top discharge type

condensing unit(s), with R-410-A Refrigerant or equivalent, vibration Isolators with suitable foundation etc. complete as required.

To have better efficiency condenser fan shall be capable to operate at different speed with respect to load. The unit shall deliver the

rated capacity and in confirmation as per IS 18728:2024 and CPWD Specifications and work even at 50°C ambient temperature

1 31.1 without tripping. The system shall be able to deliver 100% of the rated capacity upto 39 0C. The unit shall be suitable to work on 0.00

400V +/- 10%, 3 Phase, 50Hz AC power supply and BMS compatible. The unit shall be filled with first charge of the refrigerant and

ready for use as required. The condenser should be coated with a hydrophilic film to prevent water accumulation on the surface of the

heat exchanger, enhance water dispersion, and reduce the risk of degradation, thereby improving overall performance and durability.

The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as per Energy Conservation and Sustainable Building Code

(ECSBC) 2024 as below and complete as per CPWD specification, connections, inter connections etc. as required. (For capacity <40

kWr ISEER 5.4, Capacity > 40 and <70 ISEER 5.5, Capacity > 70 ISEER 5.6 for ECSBC Building) For Cooling or Heating or

Supply, Installation, Testing and Commissioning of following minimum capacity 4-way compact VRV/VRF Cassette Type Indoor

ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower,

multispeed motor, coil section with DX Copper coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary

2 31.4 supports, vibration Isolation, Corded remote control etc., suitable for operation on single phase 230 V ± 10%, 50Hz AC supply, 0.00 0.00

complete, as required. The Indoor units must shut down upon receiving a singal from the BMS System/Fire Signals. The system

shall be capable to adjust air flow as per room requirement automatically. The cooling capacity of indoor unit will be at air inlet

conditions of 27 Degree C DB and 19 Degree C WB temperature. (Make will be same as of Outdoor)

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Supply, Installation, Testing and Commissioning of following minimum capacity High wall type Indoor unit equipped with and

comfort washable (hot/cold)synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed

motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary

3 31.8 accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The Indoor units must 0.00 0.00

shut down upon receiving a singal from the BMS System/Fire Singnals. The system shall be capable to adjust air flow as per room

requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C

WB temperature. (Make will be same as of Outdoor)

Supply, Installation, Testing and Commissioning of following minimum capacity High wall type Indoor unit equipped with and

comfort washable (hot/cold)synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed

motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary

NSH-01 accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The Indoor units must 0.00 0.00

shut down upon receiving a singal from the BMS System/Fire Singnals. The system shall be capable to adjust air flow as per room

requirement automatically. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C

WB temperature. (Make will be same as of Outdoor)

Supply, Installation, Testing and Commissioning of Y/T/Multi Joints. Joints shall be of same Original Equipment Manufacturer

(OEM) make as of ODUs and IDUs

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard

drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports,

5 31.14 jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile 0.00 0.00

rubber tubular sleeves sections of 19 mm thick insulation as given below for Suction and Liquid lines, all accessories as per

specifications etc. as required :

a 31.14.12 41.27 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 30.00 1368.00 41040.00 41040.00

b 31.14.10 34.9 mm dia (OD) (Hard drawn) with tube thickness 1.62 mm Rmt 156.00 1286.00 200616.00 200616.00

c 31.14.8 28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 228.00 1157.00 263796.00 263796.00

d 31.14.6 22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 60.00 904.00 54240.00 54240.00

e 31.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 180.00 739.00 133020.00 133020.00

f 31.14.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 600.00 615.00 369000.00 369000.00

g 31.14.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 144.00 487.00 70128.00 70128.00

h 31.14.2 9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 504.00 346.00 174384.00 174384.00

i 31.14.1 6.4 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 120.00 256.00 30720.00 30720.00

6 NSH-02 Providing and fixing rigid CPVC piping complete with fittings, supports as per specifications and duly insulated with 6mm thick 0.00 0.00

closed cell nitrile rubber insulation.

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Control Transmission Wiring 0.00 0.00

Supplying and laying 25 mm X 5 mm G.I strip at 0.50 metre below ground as strip earth electrode, including connection/ terminating

7 5.9 with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be done by overlapping and with 2 sets of G.I. nut bolt & spring Rmt 600.00 160.00 96000.00 96000.00

washer spaced at 50mm) .

Providing & fixing control wiring of 2 core x 1.5sqmm copper in PVC conduit pipe of 25mm dia including providing & fixing support

@1.5mt distance CIC where it is not recessed between indoor units and out door units

Supply, installation, testing & commissioning CPRI Approved of GI Electrode Earthing with 50mm dia and 3 meter length, with

3mm thick the electrode should be hot-dip galvinised. The GI Electrode shall be pre-filled with Crystalline Conductive Material

(CCM). The GI electrode shall be surrounded with BEE MOIST compound to provide maximum contact between the electrode and

compound should be eco-friendly and having ROHS certification GI Electrode Earthing should be maintenance free and does not

require regular manual addition of water GI Electrode and providing and laying of 2 Nos. of 25 x 5 mm G.I strip from G.I rod upto

the panel. The earthing pit should be covered with PVC cover

10 NSH-05 Providing and fitting of snow/ bird protection hood in 22 gauge GI sheet with 1 inch wire mesh duly spray painted for ODUs. Jobs 14.40 8500.00 122400.00 122400.00

11 NSH-06 Additional Refrigerant charging R-410A of entire VRV system and commissioning. Kgs 1080.00 1400.00 1512000.00 1512000.00

Supplying, Installation, Testing & Commissioning of following capacity passenger Machine room less (MRL) lift with regenerative

drive as per CPWD General Specification for Electrical Works (Part-III Lift & Escalator) 2003, BIS Codes, NBC 2016 as amended

upto date having provision for barrier freeaccess as per Harmonised Guidelines & Standards for Universal Accessibility in India -

2021 of MoHUA, serving different floors in the lift shaft as per detailed specifications enclosed and as under including all other

equipment and accessories complete as required:-

(i) Speed-1 MPS

(ii) Floors-5 (G+4)

(iii) Travel -17 Meters (approx.)

(iv) Stops & opening- 5 stops and 5 openings

(v) Controller: A.C. variable voltage & variable frequency

(vi) Automatic rescue device (ARD) complete with dry maintenance free batteries as required.

vii) Operation: Microprocessor based single automatic push button/simplex selective collective/duplex collective selective

with/without attendant

(viii) Power-415 Volts+10%, 3 phase, 50 Hz, 4 wires system

(ix) Car Enclosure: Stainless steel scratch proof (Moon Rock/Honeycomb/ Hairline Finish) on all sidesand stainless steel decorative

ceiling with fans (indirect throw) and LED fitting.

(x) The car flooring should be smooth and antiskid asapproved by engineer-in-charge. (xi) Type of doors

(a) Car: Power operated, centre opening horizontal sliding stainless steel scratch proof (Moon Rock/Honeycomb/ Hairline Finish).

(b) Landing doors: stainless steel scratch proof .

(xii) A hand rail not less that 600mm long at 900mm above floor level to be fixed adjacent to control panel in the lift car.

(xiii)Voice announcement system in the car to

announce the position of the elevator in the hoist way as the car passes or stops at floor served by the elevator.

(xiv) Closed loop Control System, protection against power fluctuation, self diagnostic control, Landing doors 2 hours Fire rated,

Overload detection and protection, Overspeed Governer, Dot Matrix LED D & P Indicators In Car & Landings, BMS Compatibility,

tamper proof infrared curtain covering almost the entire height of the lift car door, Alarm horn, Anti Nuisance Operation, CCTV

camera system with 4 MP IP camera, suitable NVR and HDD for 30 days storage backup , Firemen switch, 2/3 way intercom,

Emergency Stop Switch with battery backup for fanand light fitting for 1 hour, pit ladder.

(xv) The lift doors shall have a vision panel to enable

persons with hearing impairment to signal for help or assistance in the event of an emergency.

(xvi) An appropriate technological support be provided (Through

emergency messaging |services or alarms etc.) to respond to the emergency requirements of person with hearing impairment or

(xvii) In case of failure of ARD or other electronic devices, a provision of manual rescue be provided

DRIVER FACE AND AUTOMATIC NUMBER PLATE RECORDING SYSTEM/ RECOGNITION SYSTEM, BAGGAE

SCANNER, Boom Barrier

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Supplying, installation, testing and commissioning of driver face and automatic number plate recording system/ recognition system

including high resolution camera and software set for the driver face capture and automatic number plate recording.

BAGGAE SCANNER 0.00 0.00

Baggage scanner small: computer based multi energy X-Ray baggage inspection system mounted on castor wheels capable of passing

1 NSBS-01 through bags of dimensions 540 mm (W) x 350 mm (H), belt height 750 mm to 850 mm, 22"/24" LCD Monitor, Input / Output Unit 1.20 2500000.00 3000000.00 3000000.00

rollers with frames etc. as required

Boom Barrier 0.00 0.00

1 NSBB-01 Electro Mechanical Boom Barrier with all accessories up 6 m length. No 1.00 160000.00 160000.00 160000.00

Total DRIVER FACE AND AUTOMATIC NUMBER PLATE RECORDING SYSTEM/ RECOGNITION SYSTEM,

BAGGAE SCANNER, Boom Barrier (H )=

I EPABX System(Avaya/NEC/Alcatel) 0.00

Supply Installation, Testing and Commissioning of Server Based EPABX Fully Computerized IP System, SIP Compliant. Multi slot

19: U Rack Mountable 2U Rack Expandable upto 700 Ports Presently Configuration as Below

CO Line 40 Nos.

PRI(30 Channel) 2 Nos.

Digital Extension Circuits 64 Nos.

Analog Extension Circuits 224 Nos.

64 SIP VOIP Trunk 1 Nos.

Integrated Viocemail System 1 Nos.

Supply Installation, Testing and Commissioning of 4 Level IVR software with 6 different languages and 4 time schedule (As per

3 NSEP-03 Supply Installation, Testing and Commissioning of Digital Phone (32Key). No 1.00 24000.00 24000.00 24000.00

4 NSEP-04 Supply Installation, Testing and Commissioning of Digital Phone (12Key). No 10.00 16000.00 160000.00 160000.00

5 NSEP-05 Supply Installation, Testing and Commissioning of Cordless Phone with base dilling minimum 80-100 meters range. No 1.00 12600.00 12600.00 12600.00

Supply Installation, Testing and Commissioning of Analog Speaker Phone with backlight and 4 memorable

Key.(Beetel/Panasonic/NEC)

I Total EPABX System(Avaya/NEC/Alcatel) (I )= 0.00 0.00 1838846.00 1838846.00

J Public Address System 0.00

Supply installation, Testing & Commissoing of 2 channels, 185 watts/ch at 8Ω, 280 watts/ch at 4Ω, 430 watts/ch at 2Ω, 300

watts/ch at 70V Make-QSC/BOSE/JBL

Supply installation, Testing & Commissoing of 4" Ceiling Mounted Loudspeaker, 70/100 with 8Ω bypass, includes Mounting

Hardware. Sold individually, ships in pairs. Make-QSC/BOSE/JBL

Supply installation, Testing & Commissoing of 64 network I/O channels, accommodates 8 I/O cards, dual Ethernet ports for

network redundancy, and two GPIO ports, 2RU (Field Configurable),Make-Make-QSC/BOSE/JBL

Supply installation, Testing & Commissoing of Four channels of microphone / line-level analog audio input with 48V phantom

power (Field Configured-packaged individually) Make-QSC/BOSE/JBL

Supply installation, Testing & Commissoing of Four channels of balanced, line-level analog output (Field Configured-packaged

individually) Make-QSC/BOSE/JBL

Supply installation, Testing & Commissoing of Blank Card for Core and I/O Frames (Field Configured-packaged individually)Make-

Supply installation, Testing & Commissoing of 16-Button Wall Mounted Page Station; available with Hand Held (H) or Gooseneck

(G) Microphone Make-QSC/BOSE/JBL

8 NSPA-08 Supply installation, Testing & Commissoing of Rated power 6w ,5 Step Volume Control Attenuation No 2.00 4560.00 9120.00 9120.00

9 NSPA-09 Supply installation, Testing & Commissoing of Network managable POE Switch No 1.00 14952.00 14952.00 14952.00

10 NSPA-10 Supply installation, Testing & Commissoing of Music Source bluray compitable with all DVD/CD Make-Sony/Philips No 1.00 9500.00 9500.00 9500.00

Supply installation, Testing & Commissoing of MS Equipment Rack to place the Amplifiers, Player, and motioned all the above

11 NSPA-11 devises, having regulated power supply strip for all the devices, door lock and key, openable from front and rear, and required devises No 1.00 45460.00 45460.00 45460.00

J Public Address System (J )= 0.00 0.00 983690.00 983690.00

K Furniture 0.00

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Providing in place of main table with overall size of table equal to 1200 x 600 x750mm. The table is made of 25 mm thick

Prelaminated Twin Board of E1-P2 grade edge banded with matching 2mm thick PVC lipping. Grommet provided on work surface

for wire manaement. The modesty panel is made of 25 mm thick Prelaminated Twin Board of E1-P2 grade. The understructure is

1 NSFN-01 made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC NO 15.00 16996.72 254950.80 254950.80

lipping. The HInge door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with

matching 2 mm thick PVC lipping. Handles are provided for ease of opening. Pedestals are provided with lock for security.

The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood and shall be upholstered with fabric upholstery covers

and moulded Polyurethane foam. The dimensions of seat shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of

powder coated (DFT 40-60 microns) tubular frame of dia 2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with

contoured lumbar support for extra comfort. The back shall be upholstered using Net fabric with high tenacity yarn. The dimensions

of back shall be 46.5 cm (W) x 60.5 cm (H). The HR polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness

load 16 ± 2 kgf as per IS:7888 for 25% compression. The one-piece armrests shall be injection moulded from black Co-polymer

Polypropylene. The mechanism shall be designed with 360° revolving type, 17±2° maximum tilt m pivot at centre, Upright position

locking., Tilt tension adjustment. The pneumatic height adjustment shall has an adjustment stroke of 11.0 ±0.3cm. The bellow shall be

3 piece telescopic type and injection moulded in Black Polypropylene. The pedestal shall be injection moulded in black 33% glass-

filled Nylon66 and fitted with 5 nos. twin wheel castors. The pedestal is 66.3 ±0.5cm. pitch-center dia. (76.3 ±1.0cm with castors).

The twin wheel castors shall be injection moulded in Black Nylon. Overall Dimensions of Chair shall be Seat Height - min 43.3 to

max 54.3cm, Height - min93.5 to max 104.5cm, Width & Depth of Chair as measured from pedestal - Width-76.3 cm and Depth-

The seat assembly shall be made up of 1.2 ±0.1cm. thick hot-pressed plywood shall be upholstered with fabric upholstery covers and

moulded Polyurethane foam. The dimensions of seat shall be 47.0 cm. (W) x 48.0 cm. (D). The back asembly shall be made of

powder coated (DFT 40-60 microns) tubular frame of dia 2.54 ±0.03cm. x 0.2±0.016cm thk. MS ERW tube designed with

contoured lumbar support for extra comfort. The back shall be upholstered using Net fabric with high tenacity yarn. The dimensions

3 NSFN-03 of back shall be 46.5 cm (W) x 60.5 cm (H). The HR polyurethane foam shall be moulded with density =45+/-2 kg/m3 and hardness NO 75.00 7980.34 598525.50 598525.50

load 16 ± 2 kgf as per IS:7888 for 25% compression. The one-piece armrests shall be injection moulded from black Co-polymer

Polypropylene. The powder coated (DFT 40-60 microns) tubular frame shall be cantilever type & made of dia 2.54±0.03cm x 0.2

±0.016cm.thk. M.S. ER.W. Tube. Overall Dimensions of Chair shall be Seat Height - 46.5cm, Height - 93.5cm, Width & Depth of

Chair as measured from pedestal -Width-61.0 cm and Depth-64.5 cm.

Providing and placing an office desk dimensioned 1200 x 600 x 750 mm, with a worktop made of 25 mm thick pre-laminated board

of E1-P2 grade in an approved shade conforming to IS-12823:1990 and edge banded with 2 mm thick matching PVC lipping,

featuring a soft-closing aluminum access flap on the work surface for wire management with provision for 8-module electrical

(Anchor Roma); modesty panel made of 18 mm thick pre-laminated twin board of E1-P2 grade in approved shade, also edge banded

4 NSFN-04 with matching 2 mm thick PVC lipping; cube legs fabricated from MS ERW tubes (50x25 mm and 40x40 mm, 1.2 mm thick as per NO 5.00 14869.18 74345.90 74345.90

IS:7138) with 3 mm thick HR brackets (IS:2062) welded at the top, coated with 50-micron epoxy polyester powder, and fitted with

M8 levelers adjustable up to 50 mm; cross members made from 50x25 mm x 1.2 mm thick ERW tube (IS:7138), epoxy coated and

assembled with friction fit PDC joinery and grub screws, with two cross members per table; and a power box made from 0.8 mm

thick CRCA (IS:513) with 8-module cutout fixed at access flap position.

Supplying and placing in position Reception table of the following specifications. Work Surface be Made of 25mm Thick Pre-

laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick

PVC lipping. Access Flap along with a Gromett be provided on work surface for wire management Wire Management - Power box

be made with 0.8 mm thick CRCA (IS: 513), with switch plate (8+3 Module cut out provision for Anchor Roma) which should be

fixed with worktop along the width at Access Flap position. Modesty Panel & Side Skirting be Made of 25mm Thick Pre-laminated

twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping.

Understructure be Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990,

Edge banded with matching 2 mm thick PVC lipping TOP shelf be Made of 18mm Thick Pre-laminated twin board of E1-P2 grade

5 NSFN-05 and approved shade confirming to IS-12823:1990, Edge banded with matching 2 mm thick PVC lipping. Hinge Door + Drawer unit NO 1.00 60711.00 60711.00 60711.00

be Made of 18mm Thick Pre-laminated twin board of E1-P2 grade and approved shade confirming to IS-12823:1990, Edge banded

with matching 2 mm thick PVC lipping. **Drawer bottom be made of 5.5thk MDF whiteboard Handle be provided for ease of

opening. HDU and Drawer be provided with cam lock for security. Essential Accessories - Wire Riser be made of 0.8mm CRCA (IS-

513) provided for proper wire management. Organizer Plate be made of 1.2mm CRCA (IS-513) provided for magnetic sticky notes.

Bag Hanger Hook be made of 1.2mm CRCA (IS-513) provided for bag hanging. Table Size - Length - 2400mm Depth -

1770,870mm Height - 1080mm

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

The overall dimensions of the sofa should be 132.5W x 83.5H x 81.5D (in cm). The framework should be made of solid wood. The

6 NSFN-06 material of the sofa should be of synthetic leather. It should come with a cushioned backrest and with rounded armrests. The color of NO 20.00 27196.64 543932.80 543932.80

the sofa should be Coffee Brown. The Seat height should be 45cm

Providing and placing of centre table of dimensions 120.1W x 41.1H x 59.4D in cm. The finish color should be wenge. The Primary

material used should be Tempered Glass. The number of shelves provided should be 4.

Supplying and placing of corner table. The corner table should be of size 59.9W x 49.8H x 59.9D (cm). The primary material should

be particle board. The finish color should be brown.

Providing and placing a single metal bed of dimensions 208W x 84H x 92.5D cm, in black color, weighing 40 kg, without storage,

falling within the range of 201–250.9 cm in width, 51–100.9 cm in depth and height, and inclusive of a 1-year warranty.

The VIA beam seating shall be a lounge seating system standing on connecting beam with leg assemblies. The construction of the

product shall be simple and easy to assemble.

The seat and back shall be made of 0.12 ±0.0096 cm thick CR steel perforated sheets which shall be welded to a seat/back frame

assembly made of of 0 1.9 ±0.02cm x 0.16±0.0128 cm thk MS ERW tube. Connecting Strips shall be made of 0.5 ± 0.05 cm thk HR

steel shall be welded to the structure for assembly with the connecting beam.The size of seat shall be 39.0cm. (W) X 41.5cm. (D)

and of back shall be 39.0cm. (W) X 21.5cm. (H) (Approx.). It shall be a U-shaped fabricated assembly made of 0 3.81±0.03 cm. x

0.2-±0 .016 cm thk MSERW twin tubes. The connecting tubes shall be welded together with MS base plates made of 0.25 ±0.025 cm

thick CR. Steel and mounting plate shall be made of 0.5 ± 0.05 cm thk HR Steel. Threaded inserts shall be provided on both ends of

each connecting tube for fixing leg assembly on each side. The connecting beam assembly shall be powder coated ( DFT 40-60

microns ). It shall be a 2-piece fabricated to form a box section made of 0.16 ±0.0128 cm thk. CR steel. Threaded nuts shall be

welded to the box section for fixing adjustable glide screws. The leg assembly shall be powder coated ( DFT 40-60 microns ). The

adjustable glide shall be injection moulded in black Nylon 6 and shall be used for level adjustment of the beam seating on uneven floor

surface. It shall be fitted to the leg assembly. Overall Dimensions of Chair shall be Seat Height - 46.0 cm, Height - 80.0 cm, Width &

Depth of Chair as - Width-152.0cm and Depth-46.0 cm, total width- 159.0, total depth- 57.0

Providing in place of main table with overall size of table equal to 1350 x 600 x750mm. The table is made of 25 mm thick MDF –

one side pre-laminate board with 0.4 mm PVC membrane pressed on to top. Grommet provided on work surface for wire

manaement. The modesty panel is made of 25 mm thick MDF – one side pre-laminate board with 0.4 mm PVC membrane pressed on

11 NSFN-11 to top. The understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with NO 1.00 27039.70 27039.70 27039.70

matching 2 mm thick PVC lipping. The HInge door unit is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and

approved shade edge banded with matching 2 mm thick PVC lipping. Handles are provided for ease of opening. Pedestals are

provided with lock for security.

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

SEAT/BACK ASSEMBLY: The back should be made up of 1.2 ±0.1cm. thick hot-pressed plywood & seat should be made up of 1.5

±0.1cm. thick hot-pressed plywood measured and upholstered with fabric upholstery covers and moulded Polyurethane foam. The

back foam should be designed with contoured foam lumbar support. The seat should have an extra thick foam on front edge to give

comfort to popliteal area.The Recron filling done in seat & back ( Executive chairs only) for extra fluffiness and comfort in chair.

The chair seat & back size should be

HIGH BACK SIZE 51.5 cm. (W) x 82.0 cm. (H)

SEAT SIZE 53.5 cm. (W) x 51.0 cm. (D)

HIGH RESILIENCE (HR) POLYURETHANE FOAM: The HR polyurethane foam should be moulded with density = 45±2 kg/m3

and hardness load 14 ± 2 kgf as per IS:7888 for 25% compression.

ARMRESTS : The 3-way adjustable armrest should be made of die-cast aluminium with buffing finish designed with the following

· Up-Down adjustment–7 steps (7.0 ± 0.5cm range)

· It has to & fro movement along with Swivel adjustment.

CENTER TILT SYNCHRO MECHANISM WITH MULTI LOCK : The mechanism should be designed with the following features:

· 3 position locking with anti shock mechanism.

· Tilt tension adjustment

PNEUMATIC HEIGHT ADJUSTMENT : The pneumatic height adjustment should an adjustment stroke of 9.5 ± 0.3 cm.

PEDESTAL ASSEMBLY : The pedestal should be made of die-cast aluminium with buffing finish. It is fitted with 5nos. twin wheel

castor. The pedestal should be 67.0 ± 0.5cm pitch-center dia.

(77.0 ± 1.0cm with castors).

TWIN WHEEL CASTORS : The twin wheel castors are injection moulded in Black Nylon.

WIDTH (W): 77.0 CM.

DEPTH (D): 77.0 CM.

HEIGHT (H): 110.5-120.5 CM.

SEAT HEIGHT (SH): 44.5-54.5 CM.

Providing and placing Executive Visitor Chair of cantilever type with overall dimensions 60.5 cm (W) x 65 cm (D) x 86.5 cm (H),

seat height 46 cm, having a sturdy metal frame with powder-coated or chrome finish, ergonomically cushioned seat and backrest with

high-quality upholstery, suitable for office use, including delivery, placement at site, and all necessary handling as per instructions,

with a tolerance of ±1 cm in dimensions and a minimum one-year warranty against manufacturing defects.

Providingin place of main table with overall size of table 1650 x 1650 x 750mm. The main table shall be of size 1650 x 750 x 750mm.

The side unit shall be 900 x 500 x 750mm. The table is made of 25 mm thick MDF – one side pre-laminate board confirming to IS-

14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power box are provided on work

surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board confirming to IS-14587:1998

with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick MDF one side pre-laminate board

confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm thick Pre-

laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. The pedestal is made NO 9.00 73587.16 662284.44 662284.44

of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping.

Drawer fronts made of 25 mm thick MDF one side pre-laminate board with 0.4 mm PVC membrane pressed on to top pedestal

construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325

MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Providingin place of main table with overall size of table 2350 x 2350 x 750mm. The main table shall be of size 2350 x 1150 x

750mm. The side unit shall be 1200 x 600 x 750mm. The table is made of 25 mm thick MDF – one side pre-laminate board

confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power box are

provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board confirming

to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick MDF one side pre-

laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm

15 NSFN-15 thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. The NO 1.00 133460.36 133460.36 133460.36

pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm

thick PVC lipping. Drawer fronts made of 25 mm thick MDF one side pre-laminate board with 0.4 mm PVC membrane pressed on to

top pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer

extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are

provided with lock for security.

Providing and Placing High Back Chair with overall size of 76.1 cm W x 76.1 cm D x 112.7 – 130.2 cm H x 43.1 – 53.1 cm Seat

Height. The seat is cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette and

molded high resilience polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25% compression.

Seat Size is 47.0 W cm x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube of size

1.9±0.03cm x 0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The armrest top is molded

from polyurethane and mounted on to a drop lift adjustable type tubular armrest support made of Ø3.81±0.03cm x 0.2±0.01cm thick

M.S. ERW tube having chrome plated finish. The armrest is height adjustable up to 6.5±0.5 cm in 5 steps. The adjustable tilting

mechanism is designed with following features : 360° revolving type, front-pivot for tilt with feet resting on ground and continuous

lumbar support ensuring more comfort, tilt tension adjustment can be operated in seating position, 5-position tilt limiter giving option

of variable tilt angle to the chair, Seat/back tilt ratio 1:2, The mechanism housing is made up of HPDC aluminium black powder

coated. Seat depth adjustment is integrated in the seat through a sliding mechanism. Seat depth adjustment range is of 6.0±0.5cm.

Back frame is connected to the up/down mechanism in plastic T spine. It can be adjusted in the range of 7.42±0.5 comfort the

comfortable back support to suit individual need. The pneumatic height adjustment has an adjustment stroke of 10.0±0.3cm. The

pedestal is high pressure die cast polished aluminium & fitted with 5 nos. of twin wheel castors. The pedestal is 65.0±0.5cm pitch

centre dia. (75.0±1.0cm with castors). 5 nos. of twin wheel castors are injection molded in plastic having 6.0±0.1cm wheel diameter

and assembled to pedestal.

Providing and Placing Visitors Chair with overall size of 60.9 W m x 64.2 D cm x 98.2 H cm x 44.8 Seat Height cm. The seat is

cushioned seat made of injection molded plastic outer & inner. Plastic inner is upholstered with leatherette and molded high resilience

polyurethane foam of density 45±2 kg/m³, & hardness load of 16±2 kgf as per IS:7888 for 25% compression. Seat Size is 47.0 W cm

17 NSFN-17 x 48.0 D cm. The back is cushioned made of PU foam with insitu molded M.S. ERW round tube of size 1.9±0.03cm x NO 7.00 18739.58 131177.06 131177.06

0.16±0.0128cm, upholstered with leatherette. The back size is 47.7 W cm x 76.4 D cm. The tubular frame is cantilever type and made

of Ø2.54±0.03cm x 0.2±0.016 cm thick SS 202 tube. The back connected to frame through chrome plated high pressure die casted

connector pipe.

Providing and placing an office desk dimensioned 1500 x 600 x 750 mm, with a worktop made of 25 mm thick pre-laminated board

of E1-P2 grade in an approved shade conforming to IS-12823:1990 and edge banded with 2 mm thick matching PVC lipping,

featuring a soft-closing aluminum access flap on the work surface for wire management with provision for 8-module electrical

(Anchor Roma); modesty panel made of 18 mm thick pre-laminated twin board of E1-P2 grade in approved shade, also edge banded

18 NSFN-18 with matching 2 mm thick PVC lipping; cube legs fabricated from MS ERW tubes (50x25 mm and 40x40 mm, 1.2 mm thick as per NO 9.00 16999.08 152991.72 152991.72

IS:7138) with 3 mm thick HR brackets (IS:2062) welded at the top, coated with 50-micron epoxy polyester powder, and fitted with

M8 levelers adjustable up to 50 mm; cross members made from 50x25 mm x 1.2 mm thick ERW tube (IS:7138), epoxy coated and

assembled with friction fit PDC joinery and grub screws, with two cross members per table; and a power box made from 0.8 mm

thick CRCA (IS:513) with 8-module cutout fixed at access flap position.

Supplying and placing in position Office table of the following specifications. Table size shall be 1200 Width mm x 600 Depth mm

x 750 Height mm . Table top shall be 18 mm PPB with 35 KGS , shelf shall be 12.5 KGS drawer shall be 506 KGS. The table top

19 NSFN-19 shall be 18 mm prelam particle board , 3 mm prelam MDF board. Metal parts shall be BM Slide For Keyboard plus castor mounting NO 1.00 17438.04 17438.04 17438.04

table plus locking bracket plus angle clit . Hardware shall be Screw , KD fitting , Wooden Dowel , PVC ibserts. Construction shall be

KD fitting , Wooden dowel & Angle Clit.

Supplying and placing of clerical chair. The chair type should be Non-revolving and non-tilting chair with armrest. Section size

(Diameter/Sides) of understructure should be 25 mm. The wall thickness of understructure should be 1.2 mm. There should be no

20 NSFN-20 castors. The seat upholstery material should be Polyester Fabric. The Backrest material should be of Mesh type. The width of NO 1.00 5503.52 5503.52 5503.52

backrest (mm) should be >450. Backrest height from seat level should be >=350<=450. Backrest upholstery material should be Mesh

fabrics. The Armrest type should be Moulded Armrest mounted to Frame. The Armrest movement should be Fixed

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

The overall dimensions of the sofa should be 176.5W x 83.5H x 81.5D (in cm). The framework should be made of solid wood. The

21 NSFN-21 material of the sofa should be of synthetic leather. It should come with a cushioned backrest and with rounded armrests. The color of NO 1.00 33824.70 33824.70 33824.70

the sofa should be Coffee Brown. The Seat height should be 45cm

Providingin place of main table with overall size of table 2350 x 2350 x 750mm. The main table shall be of size 2350 x 1150 x

750mm. The side unit shall be 1200 x 600 x 750mm. The table is made of 25 mm thick MDF – one side pre-laminate board

confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power box are

provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate board confirming

to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm thick MDF one side pre-

laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The understructure is made of 25 mm

thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm thick PVC lipping. The

pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with matching 2 mm

thick PVC lipping. Drawer fronts made of 25 mm thick MDF one side pre-laminate board with 0.4 mm PVC membrane pressed on to

top pedestal construction is BOX-BOX-FILE type which uses powder coated 400 MM long metal Panel Drawer Slides. Drawer

extension is 325 MM. Drawers have a soft closing & anti slam mechanism. Handles are provided for ease of opening. Pedestals are

provided with lock for security.

Providing and Placing of a 20-seater modular conference table with a main table unit of dimensions 1800mm (W) x 850mm (D) x

740mm (H) and a secondary shared table unit of 1350mm (W) x 600mm (D) x 740mm (H). The worksurface shall be constructed

from 25mm thick pre-laminated twin board of E1-P2 grade, conforming to IS-12823:1990, and shall be edge-banded with a matching

2mm thick PVC lipping. The understructure shall consist of 18mm thick pre-laminated twin board of E1-P2 grade, edge-banded with

2mm PVC lipping, with aluminum alloy 63400-WP profiles used to connect the panels, ensuring a knock-down construction. The

modesty panel shall be made from 18mm thick pre-laminated twin board of E1-P2 grade, conforming to IS-12823:1990, with a

powder-coated accent metal strip made of 0.8mm CRCA steel (IS:513) for aesthetic enhancement and epoxy polyester powder

coating (DFT 40-60 microns). The table shall include integrated wire management features such as panels made of 0.8mm CRCA

MS, epoxy polyester powder-coated, with provisions for mounting Anchor Roma 6-module plates below the worktop. A cutout on

top with two injection-moulded polymer components shall be provided to facilitate easy access to and management of audio/video

cables and power connections. Plastic ABS access flaps shall be incorporated for convenient wire and cable access. Additional

accessories shall include a 2-way nameplate, modular document shelf, and HDMI wire management kit (one packet containing 8

units). The table's worktop shall be available in various shapes to suit client requirements.

Storwel plain shall have an overall size of 916mm(W)x486mm(D)x1980mm(H) with welded construction. It should have the shelf

thickness of 0.7 mm, Back thickness of 0.8mm, Door thickness of 0.8mm (high yield strength) and all other components shall have a

thickness of 0.9mm. These components shall be made of CRCA ‘D’ grade high yield strength as per IS:513. The Storwel Plain should

24 NSFN-24 have a Mazak handle and Three way locking mechanism with Shooting Bolts. It should have a height wise adjustable shelf mounting NO 14.00 28895.84 404541.76 404541.76

which shall have a Uniformly Distributed Load Capacity of max 40 Kg. It should also have a M10 Screw type Leveller with Hex

plastic base. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10). Plenty of colour options and

shelving options shall be available.

Providing and placing of a single sided bookrack with a dimension of 1200W x 300D x 2078H that shall have a body constructed

using 0.8mm CRCA (IS:513) for side panels, frame, and cross L-bracket, with an assembly consisting of 2 tie rods, 4 fixing brackets,

and 2 turnbuckles, with tie rods made of 4mm diameter MS rods and fixing brackets made of 2mm thick CRCA IS:513 grade. The

unit shall optionally feature a wooden panel of 25mm thick pre-laminated twin board (PLT) of E1-P2 grade, edge-banded with 2mm

PVC lipping glued with hot melt EVA glue. The understructure shall be made from 0.8mm CRCA (IS:513) and consist of the

following sizes for single body: 1200mm (W) x 295mm (D) x 80mm (H) and 2400mm (W) x 295mm (D) x 80mm (H). Shelves shall

be 10-bend panels made of 0.8mm CRCA (IS:513), placed on shelf supports and secured with nuts and bolts from below. The

standard configuration shall provide 6 loading levels with 5 adjustable shelves for each main and add-on unit, each with a maximum

uniformly distributed load capacity of 80kg per shelf. The construction shall be completely knock-down. All metal sheet components

and frames shall be powder-coated with epoxy polyester powder to a minimum thickness of 45 microns for durability. The add-on NO 6.00 25760.58 154563.48 154563.48

units shall be stackable width-wise, allowing them to form a bank of racks with a common side panel up to 4800mm (W). At the rear

side of the shelves, back stiffeners made from 0.8mm thick CRCA (IS:513) shall be provided to act as separators. A label holder,

made of aluminum extrusion, measuring 296mm in length, shall be fitted to the front of the body, with a 300 GSM matte finish paper

inserted into the extrusion. Optional accessories shall include a rollout shelf, which is a pull-out tray with 2 C-shaped brackets made

from 1.2mm thick CRCA, mounted on shelf supports with adjustable height, allowing the shelf to open up to 250mm with a load

capacity of 40kg UDL. Additionally, a book separator made from 2mm thick CRCA (IS:513) shall be provided to partition and

support books placed vertically on the shelf.

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Providing and placing of a Double-Sided Bookrack shall have overall dimensions of 1200mm (W) x 600mm (D) x 2078mm (H). The

body, including side panels, frame, and cross L-bracket, shall be constructed using 0.8mm CRCA (IS:513) grade material. The

assembly shall consist of 2 tie rods, 4 fixing brackets, and 2 turnbuckles, with tie rods fixed in an ‘X’ shape, made of 4mm diameter

MS rods, and fixing brackets made of 2mm thick CRCA (IS:513) grade. An optional wooden panel of 25mm thick PLT, E1-P2 grade

board (as per FF04/DSN/STD/101) shall be provided, with machine-pressed 2mm thick PVC lipping glued with hot melt EVA glue.

The understructure shall be made from 0.8mm CRCA (IS:513), and the sizes for the single body understructure shall be 1200mm (W)

x 595mm (D) x 80mm (H) or 2400mm (W) x 595mm (D) x 80mm (H). Shelves shall be made of 10-bend panels using 0.8mm CRCA

(IS:513), and shall be placed on shelf supports and fixed using nuts and bolts from below. The standard configuration shall consist of

6 loading levels, formed by 5 adjustable shelves for each main and add-on unit, with a maximum uniformly distributed load capacity

26 NSFN-26 of 80kg per shelf. The construction shall be completely knock-down. All MS sheet metal and metal frame components shall be NO 2.00 41835.72 83671.44 83671.44

powder-coated with epoxy polyester powder, with a minimum thickness of 45 microns. The add-on units shall be stackable width-

wise, allowing them to form a bank of racks with a common side panel up to 4800mm (W). Back stiffeners made of 0.8mm thick

CRCA (IS:513) shall be provided at the rear side of the shelves, acting as separators. A label holder made from aluminum extrusion

of 596mm length shall be fitted to the front of the body, with 300 GSM matte finish paper to be inserted. Optional accessories shall

include a rollout shelf, which is a pull-out tray with 2 C-shaped brackets of 1.2mm thick CRCA, mounted on shelf supports with

adjustable height, allowing the shelf to open up to 250mm with a load capacity of 40kg UDL. Additionally, a book separator made

from 2mm thick CRCA (IS:513) sheet shall be provided for partitioning and supporting books placed vertically on the shelf.

Vertical Filing Cabinets whcih use less floor space. Size of 4 Drawer VFC shall be 1320mm(H) X 470mm(W) X 620mm(D). All the

components shall be made of CRCA . It should have 1 Point Locking Mechanism and a Rigid Knock Down Construction. The Top,

Side & Drawer Front thickness should be 0.7mm. The Frames, Drawer-inside cover and Side Back Side thickness should be 0.6mm.

The Back, Bottom and Drawer thickness should be 0.5mm. Easy to grip Full length Recess Handle shall be integrated into Metal

Drawer for easy pull out convenience. There shall be a Snap on type plastic label holder on Drawer Fronts. In addition, 28 ‘Ezee’ /

‘Visa’ files (Foolscap) from front to back of thickness 20mm per drawer can be hanged in VFC. The Centralized locking System shall

be provided along with Shooting Bolt Mechanism and 10 Lever Cam Lock. The VFC should have anti-tipping arrangement which

ensures that when one drawer is opened for use, it does not allow other drawers to be opened. The High Quality Precision Ball Slide

shall be provided with Drawer Load capacity of max 40 kg and UDL for 75,000 cycles (BS). Plain Triangular plate pop should be

riveted at the bottom corners for rigidity. Optional Accessories like Drawer Partition and Cradle for hanging A4 file folders front to

back should also be available. The finishing shall include Epoxy powder coated to the thickness of 50 microns (+/- 10).

Supplying and placing in position Canteen table of the following specifications. 4 Seater PU Coated size shall be 1135 Width mm x

1175 Depth mm x 750 Height mm . Top shall be 25 mm thick base material shall be 25 mm MDF board . On top PU painting of

minimum 2H hardness with 75% glass as per color chart .Combination color graphics on the centre . Brown Laminate on bottom

28 NSFN-28 specially profiled edges for comfort . The Understructure shall be having bend pipe structure of MS powder coated . Pipe dia 38 mm NO 4.00 25123.38 100493.52 100493.52

, 2 mm thick and it shall be fitted with top by SS machine screws . Legs shall be of MS powder coated and 38 mm dia. pipe legs are

fixed with inderstructure and table top . Glide shall be of Plastic fixed at the understructure to prevent the damage of table top during

The seat and Back are made up of injection moulded high impact strength PolyPropylene polymer compound with indoor grade UV

resistance. Seat size shall be 52.5cm x 53.2cm. Back size shall be 51.6cm x 40.5cm. The tubular welded frame is made of dia. 2.22cm

x 0.12cm and 3.5cm x 1.5cm x 0.12cm stainless steel 202 grade tube. The rubes are buff polished to give shiny finish. The shoes and

Amrest are made of high impacy strength PolyPropylene polyemr compound with indoor grade UV resistance and pressed and press

fitted with tubular frame. The overall dimensions of the chair shall be 52.4cm x 55.8cm x 84.5cm. The seating height shall be 45.0cm.

Providing and placing of Fire Resisting Record Protection Cabinet (FRRC) with 6-level lock and optional 3-wheel combination lock,

strong bolt work mechanism, and tongue-and-groove construction should withstand temperatures up to 1010°C; external dimensions

should be 1875H x 850W x 783D mm, internal dimensions 1620H x 670W x 589D mm, with a net weight of 590kg ±5% and

dimensional tolerance of ±2%. The cabinet should be fire-resistant, tamper-proof, and would be certified to meet international fire

protection standards. It would also include a minimum 5-year warranty and installation services.

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Providing and placing of Fire Resisting Filing Cabinet (FRFC) with fire-resistant compound that should withstand temperatures

exceeding 100°C, tongue-and-groove construction that should prevent the passage of flames and hot gases, each drawer should have

an independent five-sided enclosure heavily insulated with the fire-resistant compound, and it should be tested at the Central Building

Research Institute (CBRI) for 1-hour and 2-hour fire endurance and impact as per Bureau of Indian Standards IS 14581:1998; the

31 NSFN-31 drawers should move on telescopic slides with heavy-duty steel bearings, and with double telescopic slides, the entire drawer should NO 1.00 125080.00 125080.00 125080.00

be fully pulled out, allowing easy access to the rearmost file; each drawer would be provided with a self-closing latch that should

enable the user to shut the drawers almost instantaneously during emergencies, a high-precision 6-lever lock would be included, and a

push-button grip handle should be built into the index panel for opening and closing; with external dimensions of 1608H x 560W x

700D mm, a weight of 425 kg (±10%), and a dimensional tolerance of ±5%.

Providing and Placinf of Optimizer with an Overall Dimensions of TD - 2 Twin Drive Unit 2 Bay(U/C + Fittings + Cover) shall be

2400mm(W)x800mm(D)x1980mm(H) and Single door should be 2400mm(W)x400(D)x1980mm(H). The Construction shall be rigid

knock down made out of 0.8 thick CRCA steel conforming to IS : 513 . Each body shall have a main unit plus an add on unit. Finish

shall be Epoxy polyester powder coated thickness of 40 microns . Shelf construction shall be made from CRCA steel 0.8 mm thick IS

:513 .Uniformly distributed load capacity of 100 Kg . Undercarriage shall have construction in welded frame made of HR sheet 3 mm

thick conforming to IS : 2062. The Movements shall be Drive Type configuration achieved mechanically through a PU Drive Wheel

and Sprocket -Chain-Tensioner arrangement mounted rigidly onto body size. For 2-Bay Drive type each movable undercarriage shall

be provided with 2 rollers on the shaft for driving , 2 antifriction ball bearing for rolling. The roller assembly comprises of a die-cast

step wheel, 2 deep-groove ball bearings and a MS shaft. The step wheel is made of cast steel and is fitted onto the MS shaft using a

feather key. The two ball bearings are then fastened on either side of the step wheel using circlips. This entire roller assembly is then

snap-fitted into a wheel housing. The wheel housing is fixed in the Uchannel of the understructure using machine screws. This wheel-

housing is made of engineering plastic material made by injection-molding process. The entire roller assembly is designed to

withstand the maximum loads of the body. Fittings shall be centralized locking arrangement through locking stiffener mounted onto

back of single last unit so that it gets locked on channels when all the units are brought together .The ‘sprocket-chain’ arrangement is

covered by a 1 mm thk. CRCA sheet Drive Unit Cover with dimensions 1202mm x 398mm x 87mm and is fixed onto the side of the NO 1.00 413000.00 413000.00 413000.00

body. The PU handwheel is rigidly fixed at suitable height on side of the body & projects out of cover by another 99.0 mm. Fixed unit

(SD) does not have the Drive Unit Cover. Each Drive Type units shall have Locking Knob near the drive wheel for manual locking of

individual units. Knob shall be rotated to unlock position when units are to be moved. End stoppers shall be provided to prevent

derailment. The nuts & bolts are galvanized / blackodized / Zn Plated. Also total no. of loading levels per understructure shall be 24.

Label holder - It is an aluminium extrusion of length 396mm for LD/SD and 796mm for TD, fitted on to front cover of body. The

Paper is 300GSM matt milky white sticker paper, to be inserted into the aluminium extrusion. The length of paper is 394mm for

LD/SD and 794mm for TD. Over that a transparent plastic of corresponding length of 150-200 micron polythene is to be inserted.TD

units are designed with tie rod assembly options as well. it acts as a substitute to the back panels (only in twin body) if the customer

chooses to not have back panels. The assembly consists of 2 tie rods, 4 fixing brackets and 2 turnbuckles. The tie rods are fixed in a

shape of ‘X’ between two opposite shelves. The tie rods are made of 4mm diameter rods of MS while the fixing brackets are made of

2mm thk. CRCA Steel conforming to IS: 513 Gr.D.

Optimizer Body should have total 12 Numbers of Bodies including twin bodies

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

The 16-seater multipurpose tables shall include the Half Pebble table with dimensions 1890mm (W) x 665mm (D) x 770mm (H) and

the Double Seater Recta table with dimensions 1650mm (W) x 600mm (D) x 770mm (H). The worktop should be made from 25mm

thick PTL E1-P2 grade pre-laminated board (PLT), conforming to IS:12823, with edges provided with machine-pressed 2mm thick

PVC lipping glued using hot melt EVA glue. All tables shall be provided with heavy-duty table connectors made from a combination

of metal and integrated engineering plastic, facilitating the configuration of layouts using two or more tables. The modesty panel

should be made from 15mm thick PLT E2 grade, conforming to IS:12823, and edges should be finished with 2mm thick PVC lipping

glued with hot melt EVA glue. The Recta table’s modesty panel will feature a 2mm thick CRCA steel latch, powder-coated with a

minimum 45-micron thickness of epoxy polyester coating, and secured with a knurled bush made from 20mm MS rod (IS:432) in

black zinc finish, used for aligning modesty when connecting two or more tables side-by-side. The modesty panel will also be fitted

with rubber stoppers made of TPE rubber to reduce impact noise during table folding. The under-structure should be constructed

using a combination of welded MS ERW round tubes (Ø63.5 x 2mm thick) as per IS:7138, CRCA flanges (1.6mm and 1.2mm thick

33 NSFN-33 as per IS:513), and HR inside plates (5mm thick as per IS:2062), all assembled and powder-coated with epoxy polyester (min 45 NO 1.00 264649.22 264649.22 264649.22

microns). The legs will be equipped with Ø65mm lockable casters for ease of movement and can be locked at any position, with

leveling adjustments provided via two knurled disks (50mm dia, 5mm thick, made of MS bar, IS:432, black zinc finish). The tabletop

will be connected with a spring-loaded mechanism and pull handle made from MS ERW (Ø16x1.2mm thick), featuring an insert tube

of Ø12.7 x 1.6mm thick tube (IS:7138), coated with epoxy polyester powder (min 45 microns) for smooth operation. The tabletop,

along with the modesty panel, can fold upwards at the offset center pivot, which is an aluminum alloy pressure die-cast part coated

with epoxy polyester (min 45 microns), and the modesty panel will be attached to the worktop with a 90-degree rotating hinge made

from engineering plastic. All tables will be equipped with a power box containing two 2-amp universal power sockets, one 16-amp

switch, one 4-amp fuse, and a 1000mm cable with male and female GST connectors. Each table will have a wire channel and wire

clips made from 1.2mm thick spring steel (Grade 3), powder-coated with epoxy polyester (min 45 microns) to facilitate organized

routing of power cables. A power cord with a wire riser will be provided to supply power to a maximum of four tables. The wire riser

will be made from 1mm thick artificial leather, and can be zipped with the power cord to the legs of any table.

L Solar Photovoltaic Power Plant 0.00

Supplying Installation, Testing and Commissioning of on-grid Solar Photovoltaic Power Plant conforming to various applicable

standards BIS, IEC, MNRE guidelines, the Central Electricity Authority Regulations and CPWD Specifications as amended up to

date, consisting of Mono/Poly Crystalline silicon solar cells module, net metering facility, necessary control, protections, earthing,

cabling, mountingstructure, junction boxes, power conditioning units, Real time online web interfaced Data Monitoring System,

Distribution panels, grid connecting arrangement, conduits, pipes, cable trays and other accessories etc. as required.

a) High Energy Efficiency Solar Photovoltaic Module of capacity 330 Wp or above, manufactured in India, conforming to IS

14286/IEC 61215, IS/IEC 61730- Part-1, IS/IEC 61730-Part-2. Solar Photovoltaic Module conversion efficiency shall not be less

than 23% at STC with temperature coefficient of Pmax better than -0.30% per 0C. PV modules used in solar power plants/ systems

must be warranted for their output peak watt capacity, which should not be less than 90% at the end of 10 years and 80% at the end

of 25 years. Solar Modules shall be designed to operate in relative humidity upto 100% with temperature between -10 0C and +85

0C. Further, each PV module used in any solar power project must have Radio frequency identification tag with information such as

name of manufacturer, month and year ofmanufacturing, country of origin (separately for Solar cell and module), I-V curve, Unique

Serial No and Model No of the module, Wattage, Im, Vm and FF,name of test lab issuing IEC certificate.

b)Power Conditioning Unit (PCU) of 350-800 V DC Input voltage range and 415 V AC, three phase, 4 wire, 50Hz +/- 2.5 Hz,

33 17.1 output voltage suitable to generate AC with a variation of 10% at nominal voltage. Power with efficiency not less than 97%, total KWP 60.00 54280.00 3256800 0.00 3256800.00

harmonic distortion less than 3% and suitable for ambient temperature from 0 to 50 0C, Minimum IP-65 for outdoor and Minimum

IP 21 for indoor, Built-in meter and data logger, MPPT, switching devices IGBT/MOSFETs and controller Microprocessor /DSP.

PCU/inverter shall be capable of complete automatic operation including wake-up, synchronization & shutdown. The PCU shall be

able to withstand unbalanced load conforming to IEC standard with shutdown/standby mode. It must be provided with grid islanding

along with manual disconnect pole isolation switch besides automatic disconnection. Minimum protections: Mains Under / Over

Voltage, Over current, Over/Under grid frequency, Over temperature, Surge voltage induced at output due to external source, Short-

circuit, Lightening, Anti Islanding (for grid synch. Mode) and other protections as per applicablestandards. LCD/LED display of

minimum parameters: DC input voltage, DC current, AC Voltage and current (all 3 phases, in case of 3 phase), Instantaneous &

cumulative AC output power, Daily DC energy produced and other parameters applicable standard. Communication interface RS 485

c) Module mounting structure: The roof top solar plant generation units shall be installed by using supporting Aluminium/Galvanized

MS structure (mass of zinc coating shall be as per IS4759 ) having minimum head room clearance of 2.4 meter above the terrace level

/ ground level. The mounting structure would be designed to sustain wind load and seismic parameter of the site of installation. All

the structure shall be design as per applicable BIS code and the material shall also confirm the applicable BIS Code. Structural

L Total Solar Photovoltaic Power Plant (L)= 0.00 3256800.00 0.00 3256800.00

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

M 25 KLD Sewage Treatment Plant 0.00

Design , Supply,Installation, Teasting and commissioning of 25 KLD Sewage Treatment Plant with integrated Ultrafiltration

(UF) system, complete with all mechanical, electrical,piping and automation works.

Electrical Panel- Motor Control Centre 0.00

Design, fabrication, assembling, wiring, supply, installation, testing and commissioning of motor control centre fabricated out of 16

gauge CRCA sheet steel. Cable gland plates shall be provided on top as well as at the bottom of the panels. Panels shall be treated

with all anticorrosive process before painting as per specifications with 2 coate of red oxide primer and final approved shade of

powder coated paint. 2 Nos. earthing terminals shall be provided for 3 phase, 4 wire, 50 Hz supply system. Lifting hooks shall also be

provided in case of large panels. Approval shall be taken for each panel before fabrication. Quoted rates shall be inclusive of cable (in

accordance to specificaton) with earthing from panel to each motor / equipment. Design and process flow needs to be approved by

Engg. Incharge before finalising treatment technology

Motor Control Centre 0.00

100 amps TPN MCCB with the following accessories: 0.00

a) 0-500 volts 96 x 96 mm square electronic voltmeter with selector switch shall be protected by 2 amps TP MCB. 1 Set 0.00

b) 0-100 volts 96 x 96 mm square electronic ammeter with selector switch and 100./5 amps 10 VA CL:1 CTs 1 Set 0.00

c) Phase indicating lamps shall be protected by 2 amp SP MCB 3 sets. 0.00

250 amp TPN (15 KA) Al bus bar with heat shrinkable insulation sleeves. 0.00

a) Required Nos of required capacity TP MCB for direct on line starter/star delta starters and out going feeders to all the pumps/

blowers etc. (including standbies). Each compartment shall contain auto/ manual selector switch and indicating lamp with MCB's for 0.00

'ON/TRIP' status of motor.

a) All MCCB's / MCB's shall be of 15 KA breaking capacity and suitable for motor duty application. 0.00

b) All motor starters shall be provided with Auotmatic level controller. 0.00

c) DOL starters shall be used for moters below 10 HP and Star-Delta Starters for other motors. 0.00

d) Provision shall be made for providing potential free contacts to all pumps starters 0.00

3 NSEPM-02 MCC for all STP equipments/ pumps as described in sub head-A with provision for all future pump air blower etc. Job 1.20 200000.00 240000.00 240000.00

4 NSEPM-03 Supplying, installing, testing & commissioning of Cables , Conector, Cable Trays, to make Electrical Installation Complete. Job 1.20 75000.00 90000.00 90000.00

ULTRAFILTRATION SYSTEM 0.00

Providing, installing, testing and commissioning of Ultra Filtration (UF) system for further polishing treated effluent and capable of

producing 3000 litre / hour of polished water meeting the requirements . The system shall be complete with UF Feed Pumps

(1W+1S), Membranre Flushing Pumps (1W+1S), 1 No. Complete SS CIP Pump, Cartridge Filters, UF Membranes Flushing ,

complete instrumentation for automation and monitoring, Rotameters, Pressure Gauges, interconnecting pipework, electrical cabling

and switchgear, PLC+HMI, all complete as described in Scope of Work enclosed herewith.

TRANSFER PUMPS 0.00

NSTP-01 Treated Water Transfer Pumps 0.00

Providing, fixing and testing of skid mounted variables frequency drive hydropneumatic system with variable speed system

comprising of :-

Vertical, inline multistage centrifugal pumping set with stainless steel SS-304 stage casing and SS-304 impellers with stainless steel

SS-316L shaft as per IEC standards and GJL250 cast i.ron suction & discharge casing, connected to TEFC ventilated induction 0.00

motor of 2 pole, 2900rpm, suitable for 400/440 Volts, 3 phase, 50 Hz A.C. supply.

Control Panel with programmable logic controller (PLC) for cyclic operation of pumps. Pump working sequence should change after

every operation.Contractor overload relays and MCBs should confirm to IEC 898 – 1995/ specifications. Blinking indications for

pumps start, trip, low level trip, health supply should be provided in the panel along with the ammeter & voltmeter. Control panel

should also consist of cooling fan. Main incomer MCB, Outgoing MCBs, Single phase preventors complete with auto manual

swiches, dry run protection arrangements,Voltmeter/Ameter, Indication lights, Controller for dry run protection.

Pressure transmitting relay bellow type fitted with micro switch and having maximum pressure and differential scale should

confirming BS-6134 standards and IP55 protection class.

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

GI heavy class(IS:1239) Suction and delivery header with brass Ball valves with plastic coated handle(tested to 20kg/sqcm), Hot

Pressed brass OT-58 with stainless steel ball and P.T.F.E seal and O-Ring. Brass NRVs (Test pressure =20 Kg/sqcm) to be used 0.00

should be with Springs and O-Ring arrangement.

Complete set system to be mounted on a common base frame and shall follow following duty(Skid shall be powder coated ).

A Irrigation Water Transfer Pumps (Set of Two Pumps One Working + One Standby) suitable to pump tubewell water 0.00

Capacity : app. 50 lpm 0.00

7 B Flushing Water Pumps(Set of Two Pumps One Working + One Standby) 0.00

Capacity : app. 180 lpm 0.00

Supplying & installation of submersible pump set directly coupled with 5 HP motor nominal speed 2900 RPM suitable for operation

on 3-phase, 50 cycles, 400 + 5% volts A.C. power supply to give yield of 6000 LPH at a head of 50 mtrs.

Total head = 60 Mt 0.00 0.00

Flow rate = 12000 LPH 0.00 0.00

(Or as per site condition) 0.00

Supply & installation of 80 mm dia column pipe made out of 80 mm dia GI including the cost of fittings complete in all respect Jindal,

Hissar/Prakash make 'B' class pipe.

N ACCESS CONTROL SYSTEM: 0.00

Supply, installation, testing and commissioning of Access Intelligent Controller support 4 standard Weigand Interface with

enclosure , power supply ,& Maintenance free Batteries with 30 minutes back up . The controller should be on board TCP /IP .The

Controller Should have minimum of System Memory 64 MB RAM standard; expandable to 128 MB , Controller can store 4 Lakh

Card holder Access profile,Supports both direct readers and RS-485,

Supply, installation, testing and commissioning Access Control System Server Software consisting of Access Control door license ,

10 client License , with Attendance module , supports 32 readers, 12,000 cardholders .

Supply of 13.56 MHz Contactless Smart Card Readers Read Range Up to (4 cm), Dimensions 4.8 cm x 10.3 cm x 2.3 cm, Power

3 NSAE-03 Supply 5-16 VDC, Operating Temperature, Card Compatibility 16k bit (2k Byte), 32k bit (4k Byte)UL 294/cUL, Canada Nos. 20.00 17914.00 358280.00 358280.00

Supply, installation, testing, commissioning of Intel coreI- I-7(letest)Processor with EISA bus and with 3GHz minimum CPU speed,

minimum of 8 GB RAM, 512 KB cache, 52X32X52X DVDRW+Blue ray RW Drive & 2TB HDD, optical Mouse, 106 keys

keyboard, 10/100 Mbps Ethernet card, USB connection & internal modem, with for 32'' LED HDTV over HDMI Port & Original

Vista or Window 7 (Pro.) + M.S. Office (Pro.) loaded,

5 NSAE-05 Supply of I CLASS Smart Card. Nos. 240.00 676.00 162240.00 162240.00

6 NSAE-06 Supply of Single Leaf EM lock with holding force of 600 lbs Nos. 20.00 9315.00 186300.00 186300.00

7 NSAE-07 Supply of Stainless Steel Door Release Button with No/NC Contact, Nos. 20.00 3583.00 71660.00 71660.00

8 NSAE-08 Supply and laying of 8 Core 1.00 sq mm Cable 22 AWG, Shielded Cable. Mtr. 1200.00 196.00 235200.00 235200.00

9 NSAE-09 Supply and laying of 2 Core 1.00 sq mm Cable 22 AWG, Shielded Cable. Mtr. 1200.00 185.00 222000.00 222000.00

10 NSAE-10 Supply and Fixing of ''L'' Bracket with Accessories. Nos. 20.00 4567.00 91340.00 91340.00

Total ACCESS CONTROL SYSTEM: (N)= 0.00 0.00 2249790.00 2249790.00

NSAV-01 VIDEO CONFERENCING 0.00

Supply, installation, testing & commissioning of HIGH Defination video conferencing system for 1 nos. separate conference rooms.

High Definition Video conferencing Codec, suitable for use in Room size 3.6x4.6 meter as part of a Video Conferencing Solution.

ISDN and IP Compatible.

High Definition 12X Zoom Camera (Two cameras with each codec) 0.00

Table Microphone 0.00

Powerful High-fidelity Omnidirectional Microphones (33 microphones with each codec) 0.00

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

Operation Type - Remote Control

Bandwidth - 6 Mbps and higher preferable

Video Standard - H.263, H.264 and later standard

Audio Standard - G.711, G.722, G.729, ACC-LD

Video Input - Three HDMI , One DVI/VGA

Video Out - Three HDMI , Two VGA/DVI

Audio In - Two microphone input port , Two RCA input

Audio Out - One minijack for line out or One RCA pair stereo line out

Network - IPv4 and IPv6 support, H.323 and SIP support,

Preferable Features: 1.) Connect multiple camera to capture both presenter and audience.

2.) High performance architecture for most demanding needs of today an future.

3.) Provide ideal solution for meetings that requires best performance and flexibility from conference room to large lecture hall.

LED Television - Screen Size 55 inches 03 nosPicture Quality Full HD (1920*1080) Input Three HDMI, One USB, One RS323

Contrast Ratio Minimum 4000000:1 Refresh Rate 60 Hertz

LED Television - Screen Size 84 inches Picture Quality Full HD Input Three HDMI, One USB, One RS323 Contrast Ratio

Minimum 4000000:1 Refresh Rate 60 Hertz

Projector with motorized screen 1 Brightness 4000 Lumens Contrast Ratio minimum 2000:1 Aspect Ratio 16.10 ( WXGA) Input

Two HDMI, One VGA Resolution Minimum 1280*800 and higher preferable.

All compatible cables, cords, connectors and other accessories should be provided by vendor to integrate the VC components. Set 1.00 2200000.00 2200000.00 2200000.00

NSAV-02 Micro-perforated (3x3sqmm perforations) Gypsum board false ceiling for absorption: Providing&fixing perforatedGypsumfalse

ceiling , as markedinthedrawings,consistingofGIperimeterchannels of size 0.55mm thick (having one flange of 20mmand manother

flangeof 30mmandawebof 27mm) alongwith perimeterofceiling,screwfixedtobrickwall/partitionwith thehelpofnylonsleevesandscrews,

at 610mmc/c.Then suspendingGI intermediatechannelsofsize45mm(0.9mm thickwith 2 flanges of 15mmeach) from the soffit at

1220mmc/cwithceilinganglesofwidth25mmx10mmx 0.55mm thick fixed to soffit with GI cleats and steel expansion fasteners. Ceiling

section of 0.55mmthicknessm havingknurledwebof 51.5mmand two flangesof 26mm

eachwithlipsof10.5mmarethenfixedtotheintermediate channel with the help of connecting clips and in a direction perpendicular to the Sqm 157.20 4000.20 628831.44 628831.44

intermediate channel at 300mmc/c. Finished in12.5mmthickmicro-perforatedgypsumboard,

1200mmx2400mm,with3mmdiasquareperforations.The board shall have an overlay of 50mmthick, 1000GSM

polyesterwadding,appropriatelycoveredwithFGTtissue(in

thecaseofglasswool/ rockwool).Theceilingtobefinished with2ormorecoatsofmat typeplasticemulsionpaintafter

properjointing&makingsurfacesmooth.Approvedmakeof

gypsum perforated board: Knauf Danoline/ Absound Overseas micro perforated/ Saint gobin -Quattro board.

Fibril acoustical tiles in stage ceiling: Providingand fixingFibril blackacoustical tiles of size 1200x600x25 mm, to be installed over

existing MS suspension grid. Which will comprise of NRC 0.80. Approvedmake: AbsoundOverseas/HerraDesign/Acoustic India

HDFbasedsoundslatspanelingforrearwall,sidewalls, proscenium & stage front (for LF absorption): Providing and

fixingWoodmelamine finishHDF based sound slat panels with lineal perforations onwalls.The panels shall be with melamine laminate

finish of size 2430mmx128mmx17mmwith4mmslatsat28mmpitch, Toungue andGroove edges for seamlessmountinghaving densityof

750 to800kg/m3 . Thebackof the panels are perforated with 10mm diameter circular holes with a nonwoven fabric coveringof

0.2mmfor providingSound absorptionviatheacousticimpedancemethod.Panel istobe fixed on GI framework as recommended by the Sqm 144.00 6041.60 869990.40 869990.40

manufacturerwithscrewfixedhorizontal /vertical towallat every600mmc/c in tongue&groove systemonGI studs

48x36x34mmframework. The cavityof frameworkshould beinsertedwith50mmthick,1000GSMpolyesterwadding

appropriately covered with FGT tissue (in the case of glasswool/ rockwool).. Approved makes: Anutone/Absound

Overseas/Acoustic India Inc

Acoustical paneling on rear & side walls (for HF absorption):ProvidingandfixingAcousticalWallpaneling with Compressed polyester

fibre nonwoven 10mm thick panelswithadensityof200kg/m3,ofsize1200mmX600mm withanNRCof0.80to0.85. Thepanelstobepasted

with approvedconstructionadhesivesover9mmthickperforated ply(minimum20%perforations).The9mmthickperforated ply shall be

fixed over GI framing consisting of 48x36x34x0.5mm thickGI Studs wall channels & floor channels @ 600mm c/c with filling of

50mm thick 1000GSM thermally bonded polyester wadding. The insulation tobe supported fromthe backbycovering the

framewith19mmmeshGIwirenetting.ApprovedMake : Acoustic India/ Absound Overseas/AMF.

NSAV-06 Providing&fixing 100x15mm thickPolished teakwood skirtingat thebottomofwallpaneling.Theskirtingshallbe

fixedover12mmthickcommercialplytomatchthelevelof mtr 24.00 690.30 16567.20 16567.20

Digitally signed by DIWAKAR

S. Ref DSR Non-DSR

Item of work Unit Qty. Rate DSR Amount Total Amount

Item of work Unit Qty. Rate DSR Amount Total Amount

No. 2023/25 Amount

NSAV-07 Providing and fixing 90x20mm thick, in random length, Maplewoodplanks flooringwith tongue&groove joints

,fixedtopinewoodjoistofsize72x48mmat230-300mm c/c in one direction , pinewood joists to be resiliently

supportedon75x50mmrubberpads.Thecavityofframing shall be filledwith 50mm thick rockwool insulation of Sqm 60.00 8094.80 485688.00 485688.00

density48kg/cum.Polishingofflooringonexposedsurface: Inhorizontal/vertical plane (Rate for flooringshall include providing additional

framework required for housing microphone and power outlet junction boxes.

NSAV-08 Entry/exit doors for the auditorium77mmthick, acoustic doorsconsistingoffireresistantmaterials&peripheralseals all around . The door

to be laminatedwith 1mm thick laminate. The Door shutter frames to be of klin dried

chemicallytreatedsecondclassteakwood.Thedoorshutter frametobe lappedwith12mmthickBWRplydulytreated for fire retardance.Make

:Global Fire/Navair/Absound Overseas.

NSAV-09 ProvidingandfixingHinges(Steelwithbalbearings)ofsize 125X32mmfixedwith steel drive all screws of 35mm. Make: Doors, Ozone,

Providingandfixingheavydutydoor closers of load capacity of 100-120kg with all necessary parts. Make: Doors/Dorma/Godrej Each 4.00 3516.40 14065.60 14065.60

NSAV-11 Providing and fixing machine tuffed looppile high low scroll nylon carpet effective pile height 6mm, total pile weight not less than

850gm/sqm. secondary backing action back55 gms/sqm. In rolls of 3.66 mtr. width as per size, shade, design and direction of

Engineer-in-charge and as per manufacturer's specifications.The sample may be approved by the Engineer-in-charge before start of Sqm 102.00 1911.60 194983.20 194983.20

the work. The surfacearea will be measured for payment.The carpet tobe bakced with 6mm thick PU underlay. Approved make:

Absound Overseas, Birla Transasia, CCIL.

NSAV-12 Supply and fixing of fabric venetian window blinds consisting of Aluminium Head rail, rotater rail, bottom rail complete with all

fittings and accessories as aper Engg Incharge.

Total Audio vedio System (O) 0.00 6701959.60 6701959.60

ELECTRICAL VEHICLE CHARGER

18.1.3 Parkbay AC Charger (Mode -3) Power Level 2: Normal Power ~11kW/ 22 kW, 3 phase 415VAC (-40% to +20%), Frequency:50 Hz +/-

5%, output supply: 240Volt AC, Operational temperature range : -25 to 55 0C(outdoor), -5 to 55 0C (Indoor), RH upto 95%, Charging

Device as per IS-17017-1 EV-EVSE ISO- 15118 for Smart Charging, Infrastructure Socket as per IS-17017-2-2, Vehicle Connector as

per IS-17017-2-2 Vehicle Inlet/ Connector As per EV manufacturer, suitable for 4 wheelers. Indoor use : at least IP42; Outdoor use:

at least IP 54. Mechanical Strength : protection of the external enclosure against mechanical impact shall be IK08 according to IEC Each 15.00 84219.00 1263285.00 1263285.00

62262. O/L,S/C protection. Insulation Resistance > 1 M Ω. Cable Length: 7.5 . RCD having a rated residual operating current not

exceeding 30 mA; Separate RCD for multiple outputs. Telecommunication port of the EV supply equipment according to IS 13252

(Part 1): 2010. OCPP(Open charge point protocol) 1.6J upgradable to ocpp 2.0. Device Should follow 17017 series of IS codes in

general and the installation of the system shall comply with relevant IS Codes.

Parkbay DC Charger (Mode-3) Power Level 2: Normal Power ~24KW and above, 3 phase 415VAC(-40% to +20%), Frequency:50 Hz

+/-5%, output supply: DC 12/24 Volt, Operational temperature range : -25 to 55 0C (outdoor), -5 to 55 0C (Indoor), RH upto 95%,

Charging Device as per Device/protocol: IS-17017-23, EV-EVSE Communication as per IS-17017-24, ISO- 15118, Infrastructure

Socket as per IS-17017-2-2/3, Vehicle Connector as per IS-17017-2-3 Vehicle Inlet/Connector As per EV manufacturer, suitable for 4 Each 5.00 888982.00 4444910.00 4444910.00

wheelers. Indoor use: at least IP42; Outdoor use: at least IP54. Mechanical Strength: protection of the external enclosure against

mechanical impact shall be IK08 according to IEC 62262. O/L,S/C protection. Insulation Resistance > 1 M Ω. Cable Length: 7.5 m.

RCD having a rated residual operating current not exceeding 30 mA; Separate RCD for multiple outputs

Total EV Charging (P) 5708195.00 5708195.00

GRAND TOTAL (DSR + NONDSR ITEMS ) ₹ 38,30,24,066.56

GRAND TOTAL (DSR + NONDSR ITEMS ) ₹ 38,30,24,066.56

Digitally signed by DIWAKAR