Completion of incomplete Community hall

Brick Masonry in CM (1:3) with Bricks traditional size 23 x 11 x 7 cms 2nd class. The rate including cost and conveyance of all materials and labour charges etc., complete as per SS and as directed by the departmental officer in charge of the work but excluding seigniorage charges.

Filling Sand in foundation trenches as per drawing and technical specification Clause 305.3.9 MORD & 304 MORTH . The rate including cost and conveyance of all material, labour charges for filling, watering, ramming, etc., complete as per SS and as directed by the departmental officer in charge of the work but excluding seigniroage charges.

Plain Cement concrete (1:4:8) using 40 mm metal with concrete mixer. All work upto plinth level including cost of all materials and labour charges etc., complete as per SS and as directed by the departmental officer in charge of the work but excluding seigniorage charges.

Plastering with CM (1:4) 12mm thick. The rate including cost and conveyance of all materials and labour charges etc., complete as per SS and as directed by the departmental officer in charge of the work but excluding seigniorage charges.

Supply and placing of the M 20 Design Mix Concrete corresponding to IS 456 using WEIGH BATCHER / MIXER with 20mm size graded machine crushed hard granite metal (coarse aggregate) from approved quarry including cost and conveyance of all materials like cement, fine aggregate (sand) coarse aggregate, water etc., to site and including Seigniorage charges, sales & other taxes on all materials including all operational, incidental and labour charges such as weigh batching, machine mixing, laying concrete, curing etc.,complete but excluding cost of steel and its fabrication charges for finished item of work (APSS No. 402)with minimum cement content as per IS code from standard suppliers approved by the department including pumping, laying concrete, vibrating, curing etc. complete but excluding cost of steel and its fabrication charges, centering, shuttering for finished item of work as per SS and as directed by the departmental officer in charge of the work but excluding seigniorage charges.

SUN SHADE 0.60mts wide 100mm thick at fixed end and 0.50mts free end : Rate/Rmt 1st Floor

staircase 125mm thick

roof slab 110mm thick

Supplying, fitting and placing HYSD bar reinforcement in foundation complete as per drawings and technical specifications for Bars below 36 mm dia including over laps and wastage, where they are not welded. The rate including cost and conveyance of steel, binding wire, labour charges for fabrication of grills, placing in position, etc., complete as per SS and as directed by the departmental Officer in charge of the work.

Providing impervious coat to exposed RCC roof slab surface with CM(1:3), 20mm thick with 1kg of water proof compound per bag of cement laid over roof when it is green including cost of all materials, seigniorage charges, excluding conveyance charges of materials and including all operational, incidental and labour charges for mixing mortar, laying, rendering smooth and thread lining, curing, rounding off junctions of wall and slab etc,, complete for finished item of work as per SS and as directed by the departmental officer in charge of the work, but excluding seigniorage charges.

Flooring with vitrified tiles of 1st quality, set over base coat of cement mortar (1:8), 12 mm thick over CC bed already laid or RCC roof slab, including neat cement slurry of honey like consistency spread @ 3.3.kgs per sqm & jointed neatly with white cement paste to full depth mixed with pigment of matching shade, including cost of all materials like cement, sand water and tiles etc., complete, i ias per SS and as directed by the departmental officer in charge of the work but excluding seigniorage charges

Providing skirting to internal walls to 15 cm height/risers of steps with vitrified tiles screen printed and polished of size600 x 600 mm and thickness between 8-10 mm 1st quality length equal to flooring stones, set over base coat of CM (1:5) 12 mm thick with cement slurry of honey like consistency spread at the rate of 3.30 kgs per sqm and jointed with white cement paste mixed with pigment of matching shade to full depth, including cost of all materials like tiles, cement, sand and water etc., complete , as per SS and as directed by the departmental officer in charge of the work but excluding seigniorage charges.

Plastering with CM (1:3) 12mm thick. The rate including cost and conveyance of all materials and labour charges etc., complete as per SS and as directed by the departmental officer in charge of the work but excluding seigniorage charges.

Painting to New Walls with Two coats of Plastic Emulsion paint of Approved Brand and shade after throughly Brushing the surface to remove all dirt and remains of loose powdered meterials cost and conveyance of all material and labour charges etc., As per S.S.911 and as directed by the departmental officer in charge of the work for internal walls

Painting to New Walls with Two coats of Plastic Emalusion paint of Approved Brand and shade after throughly Brushing the surface to remove all dirt and remains of loose powdered meterials cost and conveyance of all material and labour charges etc., As per S.S.911 and as directed by the departmental officer in charge of the work for external walls

Providing and fixing factory made uPVC white colour casement/Casementcum fixed glazed door comprising of uPVC multi-chambered frame, sashand mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll formingprocess of required length (shape & size according to Upvc profile),uPVC extruded glazing beads of appropriate dimension,EPDMgasket,zinc alloy (white powder coated) 3D hinges and one handle oneach side of panels along with zinc plated mild steel multi point lockinghavingtransmission gear, cylinder with keeps and one side key, G.Ifasteners100 x 8 mm size for fixing frame to finished wall and necessarystainlesssteel screws, etc. Profile of frame & sash shall be mitred cut andfusion welded at all corners, mullion (if required) shall be also fusionweldedincluding drilling of holes for fixing hardware's and drainage ofwater etc.After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required sizeand of approved quality, all complete as per approved drawing & directionof Engineer-in-Charge inclusive of cost of Single / double glass panes and silicon sealent . Note: For uPVC frame, sash and mullion extruded profiles minus 5%tolerance in dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be acceptedbut no extra payment on this account shall be made. Casement door with top hung ventilator with 3D and S.S. frictionhinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ±. 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(Area of doorupto 2.50 sqm) BMT-N.84.B

Providing and fixing factory made uPVC white colour sliding glazed windowupto 1.50 m in height dimension comprising of uPVC multi-chamberedframe with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from rollforming process of required length (shape & size according to uPVCprofile), appropriate dimension of uPVC extruded glazing beads anduPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylonrollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mmsize for fixing frame to finished wall and necessary stainless steel screwsetc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage ofwater etc. After fixing frame the gap between frame and adjacent finishedwall shall be filled with weather proof silicon sealent over backer rod ofrequired size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge inclusive of cost of Single / double glass panes, wire mesh and silicon sealent . Note: For uPVC frame and sash extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable.Variation in profile dimension in higher side shall be acceptedbut no extra payment on this account shall be made. Three track three panels sliding window with fly proof SS wire mesh (Two nos. glazed & one no. wire mesh panels) made of (small series) frame 92 x 44 mm & sash 32 x 60 mmboth having wall thickness of 1.9 ± 0.2 mm and single glazingbead of appropriate dimension (Area of window upto 1.75 sqm). BMT-P.80.B

Dismantling of existing structures comprising of Reinforced Cement Concrete including T&P and scaffolding wherever necessary, sorting the dismantled material, disposal of unserviceble material and stacking the serviceble material with all lifts and lead of 1000m as per technical specification as per SS and as directed by the departmental officer in charge of the work

Supply and Fixing of 20mm dia 1.50mm thick P.V.C. pipe (ISI MARK) IS :9537-part-3 rigid PVC concealed in wall with all required accessories including masonary work for light, fan and separate plug point with well seasoned wooden deep box including all labour charges etc., complete.

Supply and Fixing of 25mm dia (ISI MARK) PVC 1.5 mm thick pipe concealed conduit, duly threadig at Joints in Slab and on wall with required accessories including chiselling the wall and necessary Masonary and all labour charges etc. complete for run of mains.

Supply and fixing of Three phase Electronic energy Meter thefr phan AC,50HZ as per IS13010 up to 40A range with 200% over load capacitycomplete with connections etc., complete on the existing board. This rate incluiding cost of all materials all labour charges, transporation charges other incidental charge etc complete as per IE Rules and as directed by the departmental officer incharge of work. MAT-03992 Makes : ONZERVE/ELMEASURE/MECO/HPL/HAVELLS/ Lavritze/Knudsen (formerly L&T) ABB.

Supply of 4.00 Sq mm ISI marked FRLS/ FRLS-H / HFFR / ZHFR PVC insulated flexible copper cables 1100V grade as per IS: 694/1990 & IS:17048/2018 specification for copper cable including all labour charges etc.,complete. This rate including cost of materials, transporation to site of work, other incidental charges all labour charges, fixing as per IE Rules and as directed by the departmental officer incharge of work

Supply and Run of 4 of 10 Sq.mm WPSC Aluminium cable along with No.10 SWG G.I bearer wire ON BOTH SIDES through PVC cleats with all accessories including Cost and conveyance of all the materials and all labour charges etc., complete for service mains.This rate including cost of materials, transporation to site of work, other incidental charges all labour charges, fixing as per IE Rules and as directed by the departmental officer incharge of work

Supply of (8 +24) 8 Way TPN DB Horizontal with IP 43, . protection suitable for installation of 24 Nos of SP outgoing MCBs and for 1 No 4 pole, MCB/Isolator incomer along with provision for 1 No of 4 Pole RCCB/ELCB etc., complete as per IS 8623; IS 13032; IEC 61439-3. This rate incluiding cost of all materials all labour charges, transporation charges other incidental charge etc complete as per IE Rules and as directed by the departmental officer incharge of work. Makes: Legrand (Ekinox 3) / Schneider-A9/Hager - Novello+/ Seimens/Havells STADx/ Lauritz Knudsen (formerly L&T) -Newrange/Indo Asian-Opti Pro/ HPL (Techno)/ Anchor (Uno Plus)/ABB-ITUS

Supply and Run of 4 of 16 Sq.mm WPSC Aluminium cable along with No.10 SWG G.I bearer wire ON BOTH SIDES through PVC cleats with all accessories including Cost and conveyance of all the materials and all labour charges etc., complete for service mains.This rate including cost of materials, transporation to site of work, other incidental charges all labour charges, fixing as per IE Rules and as directed by the departmental officer incharge of work

Supply of 3 Core 2.5 Sq mm ISI marked Flat Copper cable of ISI for Submersible Motors confirming to IS: 694:1990. This rate incluiding cost of all materials all labour charges, transporation charges other incidental charge etc complete as per IE Rules and as directed by the departmental officer incharge of work. MAT-02795

Supply and run of 1 of 14 /0.3mm (1.0 Sq.mm) FR P.V.C. insulated flexible copper cable in existing pipe for earth continuity including all labour charges etc., complete.SoR 2025-26

Supply and run of 2 of 36/0.3mm (1.5 Sq.mm) F.R P.V.C. insulated flexible copper cable in existing pipe for mains inlcuding all labour charges etc., complete. SoR

Supply of 48" (1200mm) Sweep 5 star rated BLDC (Brush less Direct Current) Ceiling Fan with double ball bearings, input voltage 230V AC converted to 24 V DC, power input not more than 30W, air delivery not less than 220 cubic meter/min and a minimum service value of 7.0, with remote and without Regulator.Makes: As per list of recommended brands.

Supply and fixing of 20-24W, not less than 1100mm length LED batten light with extruded aluminum housing and polycarbonate cover, input voltage AC 220 - 260 Volts, with high power LEDs, having System Efficacy of >=100 lumens/watt , PF>0.9, Surge protection: 2KV, THD<15%, with inbuilt driver and frosted cover CCT: 3000K - 5700K, minimum CRI>70, etc., complete with earth connection and not less than two years warranty. Makes: As per list of recommended brands as category I. ELEC-3.8.13

Supply, Transportation and Fixing of ........, 1100mm length Linear Profile LED Luminaire recessed/surface mounted with Aluminum extrusion, powder coated cover, input voltage AC 90-270 volts with PF>0.95, with high power LEDs, having system efficacy of >=100 lumens / watt, surge protection: 2KV, THD<15%, with inbuilt driver and frosted cover CCT: 3000K - 5700K, minimum CRI>70, .etc., complete including fixing of 23W Linear light duly recessed in the ceiling/surface mounted by hanging from ceiling with necessary mounting arrangements, jointing kit, connecting wire leads etc., and all accessories, giving connections and all labour charges etc., complete with earth connection and not less than two years warranty. Makes: As per list of recommended brands.

Drilling of Bore well by down the hole hammer drilling to a finished dia of 112/165 mm dia in all formations suitable for down the hole hammer drilling such as medium hard rock formation to hard rock formation, all consolidated formation etc. and drilling in over burden to dia not less than 200 mm etc and reaming the bore well to suit insertion of suitable casing pipe etc., including insertion of casing pipe with couplings, caps any other relevant materials upto required depth as directed by the department including transportation of drilling rigs and supporting vehicle and including bore development (Flushing of Bore Well at an average pressure of 150 PSI) conducting yield test, consumables charges, Crew charges required in fixation of pipe assembly completely done to the satisfaction of the department and including all labour charges but excluding all taxes, the cost of casing pipe, couplings, cap etc., The entire work should be carried out as per IS -2800 Part I & II 1979 and amended from time to time. Drilling of Bore well 112 mm dia. up to 150.00 m depth

Manufacture, Supply and Delivery of Unplasticised PVCs Pipes for potable water supplies conforming to IS : 4985/2000 (3rd revision) with bell ends (Socket) as per specification in light Grey/Natural Ivory Grey/ Any other Color (except White) inclusive of transportation to the sub-divisional stores anywhere in AP excluding all PVC PIPES FOR 6 Kg/Cm2 2025-26 Water supply 110 mm dia 6 Kg /cm2

Supply and Transportation of …1.00 HP 5star rated submersible motor pumpset, confirming to IS 8034 and motor confirming to IS 9283 with waterproof winding, pump shall be suitable for various delivery head and discharge with stainless steel shaft motor suitable for working on 240V ± 10%, single phase 50 Hz AC supply, etc complete for 4" Bore well. Makes: As per list of recommended brands as category I MAT-03641

Fabrication , transportation and supply of suitable size panel board for single phase submersible motor 2 to 3HP consisting of relay, Contactor, starting and running capacitors, Voltmeter, Ammeter,indicator lamps, MCB , on/off switch including supply and fixing of DOL starter of complete.,. MAT-03712

Manufacture, Supply, & Delivery of HDPE Pipes conforming to IS 4984 - 1995 including transportation to any where in A.P, excluding excise duty, sale tax and specials etc., complete. HDPE PIPES FOR 6Kg/Cm2 2025-26 PE100 grade 50 mm (OD) MAT-07261

Supply and fixing of 2 modular 6A 3pin plug Modular socket with shutter and 6 Amps Modular switch control on Common covered frame board including earth connection and all labour charges etc., complete on wall. This rate including cost of materials, transporation to site of work, other incidental charges all labour charges, fixing as per IE Rules and as directed by the departmental officer incharge of work

S & F Gunmetal Gate (GM peet) valve as per IS - 778 Class - I, Indian make heavy type - 25 mm NB Size MAT-01845

Supplying & fixing Gunmetal (GM) Horizontal Check (Non return) Valve as per IS-778 I-class heavy duty - 25 mm NB Size MAT-01854

Manufacturing supply and fixing of M.S.Grill Gate with M.S.Angulars, M.S.Flats. The rate including cost and conveyance of all material and labour charges for fabrication of steel work including cost of welding rods , power charges and fixing the grills in position etc., complete as directed by the departmental officer in charge of the work.

Manufacture as per BIS:12592 (Part 1&2) Supply & Delivery of manhole covers and frames with ISI marking anywhere in A.P., F.O.R. destination including, loading, un-loading & stacking at site but excluding all taxes. MAT-08226