COMPREHENSIVE MAINTENANCE FOR BR NATURE WORK IE SUNKEN TREATMENT SANITARY FITTINGS ATT PLASTERING PERIODICAL SERVICES JOINERY PARAPET REPAIR AT ZONE B RESIDENTIAL AREA AND DAY TO DAY MAINTENANCE TO BR NATURE OF WORKS FLOORING PLASTERING PERIODICAL S

Taking down chowkhats or frames with shutter (without taking off shutters from the frame) of size exc 1.5 sqm but not exc 4 sqm and making good to distrubed surface without any extra cost complete all as specified and directed.

Taking down cement plaster/grit wash from facia, walls of any description etc and removing debris/ malba to low line area out side MoD land complete all as specified and directed.

Taking down chowkhat or frames with shutters (without taking off shutters from the frame) not exc 1.5 Sqm and making good to distrubed surface without any extra cost complete all as specified and directed.

Demolition of brick work or stone masonary built in cement mortor including all quoins & jambs etc. complete all as specified and directed

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc laid bedded and pointed in any mortar, complete all as specified and directed.

Taking down of shutters of any description n.exc 1.0 Sqm each complete all as specified and directed

Dismantling wrought iron or mild steel work of any description not otherwise provided for work including doors, gates, angle post etc. complete all as specified and directed by engr-in-charge

Demolition of cement concrete in ground floors and pavings etc not exc 15 cm thick above or below ground level complete all as specified and directed.

Demolition of reinforced cement concrete as in RCC slabs, beams, etc drains or manhole covers of any description and in any position not otherwise specifically provided for complete all as specified and as directed.

Taking down existing roof membrane with concrete padding upto original roof and removing the debris from the site etc complete all as specified and directed

All as item No. 04 above but exc 1.0 Sqm and n.exc 2.0 Sqm each.

M&L for PCC 1:5:10 Type E2 (using 40mm graded crushed stone aggregate) as in filling sunken floor complete all as specified and as directed by Engineer-in-charge. (upto 12 storey of building).

Supply and applying two coats of High performance elastomeric cementitious waterproof coating sandwiched with 45 GSM glass fibre reinforcement on the entire floor and 1.0 m of all walls of all toilets as per following methodology:- Cleaning of exposed concrete surface by mechanical means or by hydro blasting to remove laitance, loose particles, contamination etc. which may hinder bonding. Covering of RCC joints with PCC (1:1.5:3) mixed with Integral Water Proofing compound. Applying one coat of Waterproofing membrane to concrete surfaces followed by application of 45GSM glass fibre on the wet surface. Applying second coat of waterproofing membrane at the right angles to the direction of first coat. Second coat shall be applied after the first coat gets dry. Sprinkling fine aggregate immediately after the application of second coat to get the mechanical key for protective plaster. Curing to Water proofing membrane to be carried out for minimum period of 3 days with ponding complete. The Water Proofing Product Should have Mixed density: 1.68g/cc (brushable consistency). Adhesion to concrete : >1N/mm2. Static crack accommodation: 1mm

Dismantaling floors hearth or wall tilling including cement mortar bedding (but not backing) removing serviceble tiles to store and rubbish off the premises complete all as specified and directed

Dismantling water tanks and removing from site of 500/750 litres capacity complete all as specified and directed.

Dismantling water tanks and removing from site of 1000 litres capacity complete all as specified and directed.

S&F 500 litres capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I all as specified and directed

S&F 750 litres capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I all as specified and directed

S&F 1000 litres capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I all as specified and directed

S&F as in repairs PVC lid / cover for PVC water tank 500 / 1000 litre capacity of make Sintex/ Polycon/ Fusion/ Sheetal) incl removing old broken lids complete all as specified and as directed.

Disconnecting existing tanks, setting aside (or lowering if required ) for repairs ,cleaning,etc.and hoisting if required reconnecting and refixing in position including cleaning and removing all scales and dirt from tanks and from mouths of circulating pipe etc for 500 ltr to 1000 ltrs capacity of tanks complete all as specified and directed.

S&F as in repairs PVC internal syphone kit with handle suitable for low level flushing cistern having10 ltrs capacity, white, valveless, syphonic action type complete all as specified.

S&F in repairs flush pipe/L bend for PVC low level flushing cistern as suitable for EWC/ Orissa pattern pan including jointing to WC complete all as specified and directed.

S&F as in repairs chromium plated waste coupling fitting 100mm / 75mm bore pipes to kitchen sinks complete all as specified and directed.

Disconnecting existing tanks, setting

aside (or lowering if required) for repairs ,cleaning,etc.and hoisting if required reconnecting and refixing in position including cleaning and removing all scales and dirt from tanks and from mouths of circulating pipe etc for 250 ltr to 500 ltrs capacity of tanks complete all as specified and directed.

S&F in repairs 32mm/40 mm dia PVC waste pipe for WHB/Urinal 60cm long with union complete all as specified and directed.

S&F in repairs 10 ltrs capacity PVC low level flushing cistern valveless,syphonic action type with inlet ball valve float and handle including brackets complete all as specified and directed.

S&F in repair Toilet paper holder with flat recessed type stain less steel complete all as specified and directed.

S&F in repair vitreous china white wash hand basin flat back of size 550 x 400 mm excluding CI/MS brackets complete all as specified and directed.

S&F in repairs CP brass bottle trap 32 mm dia including joining to waste fitting and waste pipe complete all as specified and directed.

S&F in repairs CP grating 100/125 mm dia round fix on floor / nahani trap fixed with cement mortar complete all as specified and directed.

S&F in repairs plastic water closet seat cover white closed pattern with flat bottom end cover and mild steel chromium plated hanging device complete all as specified and directed.

S&F in repairs vitreous china Squatting pan Orissa pattern of size 580X440 mm white with integral foot rest water closet including provn of lime concrete bedding including connections to flushing cistern/pipe and making good disturbed portion to match existing surface complete all as specified and directed.

S&F in repairs PVC connection 15mm dia 45cm long with 2 Nos PTMT checknuts with washer complete all as specified and directed.

S&F in repairs PVC connection 15mm dia 60cm long with 2 Nos PTMT checknuts with washer complete all as specified and directed.

S&F in repairs 15mm dia bib tap cast copper alloy but fancy type quarter turn chromium plated long body complete all as specified and directed.

Supply and fix in repairs brass spindles for bib tap and angle cock etc complete all as spd and directed.

Supply and fix in repairs Brass spindle for WHB mixer and Wall Mixer and concealed stop cock complete all as spd and directed.

S&F in repairs in 20mm dia ball valve high pressure of PTMT complete with aluminium rod with polyplast ball complete all as specified and directed.

S&F in repair 15mm dia brass but fancy type quarter turn chromium plated pillar tap(swan neck) fancy type with fly nut capstan head screwed complete all as specified and directed.

S&F in repairs 15 mm dia stop valve CP with long shank (concealed type) but fancy type quarter turn cast copper alloy screwed down high pressure chromium plated complete all as specified and directed.

M&L in repairs 75mm dia cast iron floor trap with grating including jointing to waste pipe fixed in cement concrete B-1, (1:2:4)all as spd & directed

S&F in repairs sand cast iron `P' or `S' trap 100mm dia all as spd & directed

S&F in repairs 15 mm dia angle valve chromium plated brass but fancy type quarter turn complete all as specified and directed.

S&F in repairs 15 mm dia angle valve double ways chromium plated brass but fancy type quarter turn complete all as specified and directed.

S&F in repairs in 25mm dia ball valve high pressure of PTMT complete with aluminium rod with polyplast ball complete all as specified and directed.

S&F in repairs vitreous chinaware wash down water closet pan pedastal pattern white excluding fixing bolts but including jointing to flushing cistern and flush pipe anti syphonage pipe etc complete all as specified and directed

S&F in repairs long body Bib taps but fancy type quarter turn chromium plated cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule and fixed quarter turn, suitable for 15mm bore pipe complete all as specified and directed.

S&F in repair 20 mm size Gun metal globe or gate valves with iron wheal head,screwed both ends for iron pipes and fixed complete all as specified and directed.

Supply and fixing as in repair 15mm bore tubes "medium grade" galvanized with and incl all fittings complete to walls and ceiling or laid in floors complete all as specified & directed.

Supply and fixing as in repair 20mm bore tubes "medium grade" galvanized with and incl all fittings complete to walls and ceiling or laid in floors complete all as spd & directed.

S&F in repair Stainless steel sink, 1.00mm thick for kitchen or laboratory with plug waste pipe, washers including cantilever cast iron brackets connecting union etc. overall size 495mm x 420mm with bowl size 410mm x 330mm x 160mm complete all as specified and directed.

S&F in repair 110mm bore PVC (SWR) pipe single socketed in any length with rubber ring joints fixed to wall complete all as specified and directed.

S&F in repair 110 mm bore PVC (SWR) bends with rubber ring joints complete all as specified and directed.

S&F 75mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall including clamps as required, fixed as in repair complete all as specified.

S&F 75mm dia PVC (SWR) bends with rubber ring joints fixed as required complete all as specified.

S & F as in repair 32mm dia CP waste coupling, for WHB, with long screwed shanks and fly nuts, flange and based in red lead cement and fixed all as specified.

S & F as in repair 40mm dia CP waste coupling, for WHB, with long screwed shanks and fly nuts, flange and based in red lead cement and fixed all as specified.

S&F as in repairs CP Health faucet with 1.50 Mtr flexible chromium plated tube and hook fixed to angle valve 15mm bore with accessories complete all as specified and directed.

S&F as in repairs Chromium plated jet spray with CP connection pipe for EWC, 15mm bore with fittings, complete all as specified and directed.

S&F in repair 25 mm size Gun metal globe or gate valves with iron wheal head,screwed both ends for iron pipes and fixed complete all as specified and directed.

S&F in repair 50 mm size Gun metal globe or gate valves with iron wheal head,screwed both ends for iron pipes and fixed complete all as specified and directed.

S&F as in repairs Chromium plated shower roses 125 mm size fixed with or without swivel joints, any size, including fixing to steel pipe or union, complete all as specified and directed.

Cutting chases, pining in making good to facings where required & pointing in cement mortar1:3 to ends etc or edges of landings, steps cills,sunshades, shelves,lintels,etc and cutting chases for concealed water tubing and making good,cutting n.exc. 10cm girth in brick walls all asdirected.

Supplying and laying of CPVC pipes 25 mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down of old pipes complete all as specified.

Supplying and laying of CPVC pipes 20mm outer dia SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors including taking down of old pipes complete all as specified.

S&F CPVC Brass Elbow fitting suitable for CPVC pipes 25mm outer dia SDR 11 & Plain CPVC SDR 11 pipes complete all as specified.

S&F CPVC Brass Elbow fitting suitable for CPVC pipes 20mm outer dia SDR 11 & Plain CPVC SDR 11 pipes complete all as specified.

S&F CPVC Brass TEE fitting suitable for CPVC pipes 25mm outer dia SDR 11 & Plain CPVC SDR 11 pipes complete all as specified.

S&F CPVC Brass TEE fitting suitable for CPVC pipes 20mm outer dia SDR 11 & Plain CPVC SDR 11 pipes complete all as specified.

S&F CPVC Brass UNION fitting suitable for CPVC pipes 25mm outer dia SDR 11 & Plain CPVC SDR 11 pipes complete all as specified.

S&F CPVC Brass UNION fitting suitable for CPVC pipes 20mm outer dia SDR 11 & Plain CPVC SDR 11 pipes complete all as specified.

S&F CPVC Brass FTA female adaptor fitting suitable for CPVC pipes 25mm outer dia SDR 11 & Plain CPVC SDR 11 pipes complete all as specified.

S&F CPVC Brass FTA female adaptor fitting suitable for CPVC pipes 20mm outer dia SDR 11 & Plain CPVC SDR 11 pipes complete all as specified.

S&F in repair vitreous china EWC with cistern in one piece including all fittings and fixture of size 59X36X71 Cm all as specified and directed.

S&F in repair 75 mm size Gun metal globe or gate valves with iron wheal head,screwed both ends for iron pipes and fixed complete all as specified and directed.

Supply and fixing in repairs brass chromium plated tubular towel rail 20mm dia 60 cm long between flanges, fixed to walls with necessary screws complete all as specified and directed.

Supply and fixing in repairs brass chromium plated tubular towel ring having dia of ring not less than 150mm fixed to walls with necessary screws complete all as specified and directed.

S & F in repair for brass chromium plated but fancy type quarter turn Centre Hole Mixer for WHB screwed for 15 mm bore pipe complete all as specified and directed

S & F in repair for 15mm bore brass chromium plated but fancy type quarter turn Wall Mixer with Provision for Overhead Shower with 115mm long Bend Pipe on Upper Side, Connecting Legs & Wall Flanges complete all as specified and directed.

S & F in repair for 15mm bore brass chromium plated Sink Mixer, Connecting Legs & Wall Flanges complete all as specified and directed.

S & F in repairs, CP, but fancy type quarter turn Wall Mixer 3-in-1 System with Provision for both Hand Shower and Overhead Shower Complete with 115mm Long Bend Pipe, connecting Legs & Wall Flange (without Hand & Overhead Shower) complete all as specified and directed.

M&L for cast iron soil, waste and vent pipes 100mm dia in any length with or without ears, with cement joints, laid in trenches, in floors or wall including taking out old unserviceable pipes complete all as specified and directed

M&L for white cement in traps/sides of 'P' or 'S' trap/joint of flush pipes and WC and making good complete

M&L for cast iron soil, waste and vent pipes 75mm dia in any length with or without ears, with cement joints, laid in trenches, in floors or wall including taking out old unserviceable pipes complete all as specified and directed

M & L for machine made Rubber moulded precast concrete interlocking paver block (coloured),pre polished of any shape and size with grey cement and pigment confirming to IS 15658-2006 of 60 mm thickness M-35 Grade, over and including 25mm average thickness sand cushioning complete all as spfd and directed.

Material & Labour for 75mm thick cement concrete type D-2,1:4:8 (40mm graded stone aggt) as in sub base concrete all as specified & directed.

M&L for removal of leakage of RCC water storage tank with use of concrete binding agent brush it along the cracks, hydraullic cement mixture with appropriate chemical (Dr fixit pidifine 112) or equivalent with every 50 kg bag of cement and cleaning liners including removing loose plasters/concrete and making good and all as specified and as directed.

S&F Mild steel bands, straps, supports or stay, for rain water, ventilating pipes including bolts if reqd, hooks (stay) heavy for large gates hook and pintel large hasps and staple, chains hand made sliding bolts clamps, hold fasts wall ties etc etc hooks for hanging fans plain angle cleats for securing purlins to wood truss or rafter, knee piece inserts, two way and three way straps, plate washer and similar small articles confirming to Fe-410-0 or Fe-310-0 all as spd and directed

M&L glazed ceramic coloured tiles 450x300x6-7mm in vertical surfaces set and jointed in in neat cement slurry and pointed in coloured cement to match over and including 10mm thick rendering in CM 1:4 complete all as specified and directed

Use and waste of form work to soffits of suspended slab such as roof slab, floor slab, landing and similar work not exceeding 200mm thick surface flat for rough finished surface of concrete complete all as specified.

Use & waste of form work to to edge of concrete flats etc exc 10 cm but not exc 20 cm wide/thick for fair finished surface of concrete all as specified.

S&F Factory made precast perforated heavy duty drain/ manhole covers including MS frame plate and including reinforcement as per IS 12592 : 2002 with size 1.00mtr x 0.50mtr x 75mm thickness complete all as specified and directed by Engineer-in-Charge.

S & F Framed work as in Mild Steel Gate of angle or other section with gusset plate, rails, braces, stair case, barreled iron doors,ladders; framed balusters; walk ways; railings; framework of water tanks, cover grills and similar work etc Fe.290.Gde-E-165 complete drilled for fixing of steel sheeting or other covering including welding work ,(PCC 1:1.5:3) etc to be prepared for hanging or sliding with and including either hooks,hinges,necessary holdfasts or steel hanging door fittings, locking arrangement, gate closer, stopper etc and hanging also fastening and fixing in building upto 8 mtr height complete all as spfd and directed by engr in charge.

M&L for cleaning exposed mineral substrate like stone/Grit wash/Brick/Concrete/cement paint and removing dirt, dust, bird dropping, grease, oil, algae, fungus, vegetation trowth etc with and including suitable chemical emulsion with fine silica, mixed with clean water as per manufacturer's instruction by using suitable machine gun nozzle (creating high pressure for flow of the water) , without causing any scratching/damage to the existing surface and applying breathable, non-film forming, non reactive, antifungal and water repellant silane/siloxane silicone chemical diluted with solvent mineral Turpentine oil in the ratio of 1:12 (one part of approved chemical:12 part of mineral Turpentine oil) , on the existing surface with two coats of ready mixed chemical to give uniformity as per manufacturer's instructions complete all as specified and directed (Rate is inclusive of all materials and labour involded with scaffolding)

M&L for providing cement concrete type B-0 (Using 12.50mm graded stone aggregate) as in padding and benching & filleting all as specified and directed.

M&L for 10mm thick screed bed or bedding over roof surfaces when concrete is still green with and including WPC in cement mortar 1:3 complete all as specified and directed

Preparation of plastered surfaces of roof and laying 3mm thick APP (Atactic Polypropylene Polymer) modified prefabricated five layer, weight not less than 3.6 kg/Sqm water proofing membrane, black finished reinforced with non woven polyester matt laying over a coat of bituminous primer @ 0.40 Ltr / Sqm and two coats of Bitumen based UV reflective paint with aluminium finish over APP membrane. The membrane shall be laid using butane torch and sealing all joints etc all as specified and directed.

M&L 100 mm thick cement concrete type D-2,1:4:8 (40mm graded stone aggregate) as in sub floors, filling and mass concrete etc complete all as specified.

Anti Termite Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed

Anti Termite Treatment of voids in masonry using chemical emulsion one litre per hole, at 300mm intervals including drilling holes at 45 degree and replugging them with cement mortar 1:2 (1 cement

: 2 coarse sand) to match the existing floors complete all as specified and directed

Supply and fixing factory made chequered cement concrete prepolished coloured tiles 300mm x 300mm x 25mm thick, set jointed and pointed in neat cement slurry with grey cement mixed with pigment to match the colour of tiles, laid over and incl 20mm thick screed bed in CM 1:4, complete all as specified & directed.

Anti Termite Treatment at points of contact of wood work by chemical emulsion (in oil or kerosene based solution) @ 0.5 litre/hole by drilling 6mm dia holes at a downward angle of 45 degree at 150mm centre to centre and sealing the same complete all as specified and directed

M&L rendering 15mm thick in CM (1:4) on fair faces of brick work or concrete surfaces finished the surfaces even and fair without using extra cement and using water proofing compound as per manufacturer instruction complete all as specified and directed

M&L for RCC work (Nominal Mix) (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in slabs supported on walls, man hole cover ,drain covers with perforated hole, Shelves etc and like complete all as specified and as directed.

Removing Debris/ demolished materials by mechanical means including loading, transporting, unloading to outside MoD land from 5KM upto 20KM lead at approved municipal dumping ground complete all as specified and directed.

M&L rendering 5mm thick in CM 1:3 on fair faces of brick or concrete surfaces of walls, facia/soffits of slabs etc to be finished even and smooth (w/o using extra cement) including setting coat complete all as spd

M&L for washed stone grit plaster on exterior walls in two layers, under layer 12mm cement plaster 1:4 (1 cement: 4 coarse sand) furrowing the under layer with scratching tool, applying cement slurry on the under layer @ 3kg of cement per square metre, top layer 15mm cement plaster 1:1/2:2 (1 cement: 1/2 coarse sand: 2 stone chipping 10mm nominal size) in panels with groove all around as per approved pattern including scrubbing and washing, the top layer with brushes and water to expose the stone chippings complete all as specified.

Forming groove of uniform size 15mm wide and 15mm deep in the top layer of washed stone grit plaster as per approved pattern using wooden battens, nailed to the under layer including removal of wooden battens, repair to the edges of panels and finishing the groove complete as per specifications and directions of Engineer-in-charge

M&L rendering 15mm thick in CM (1:6) on other than fair faces of brick work or concrete surfaces even & smooth without using extra cement complete all as specified and directed

M&L preparation of newly plastered surfaces of walls and applying two coats of oil bound distemper (white or tinted) over a coat of alkali resistant primer complete all as specified and directed.

M&L preparation of newly plastered surfaces of ceiling and applying two coat of oil bound distemper(white or tinted) over a coat of alkali resistant primer, complete all as specified and as directed.

M&L for applying one coat of oil bound distemper on walls including preparation of old decorated surfaces including filling minor holes with wall care putty and brooming down and scrabing down smoke soot, moulds, moss and efforescent salts greasy spots complete all as specified and as directed

All as per item No 118 here-in-before but on ceiling

Supply only liquid water proofing compound as required complete all as specified and directed.

M&L for Rough cast plaster including 15mm thick rendering in CM 1:3 on brick work or concrete surfaces complete as specifed in SSR part -I clause 14.22 complete all as specified and directed. Note :- Rough cast finish to be as below :- After applying the under coat of cement mortar 1:3 and while it is still in plastic state the roughcast mixture consisting of crushed stone or fine gravel aggregate (which is generallly of size between 6 to 12 mm depending on the texture required) mixed with coarse sand and cement in the ratio of 1:1:1 shall be applied and finished even. The mix of cement and sand shall be made slightly wetter than normal for rendering to ensure that larger aggregate are thoroughly covered.

M&L for Complete removal of existing treatment from internal plastered or unplastered surfaces of walls and applying two coats of oil bound distemper on walls after completion of putty work (if reqd on site) on scrapped/uneven surfaces of any description to match with the existing surfaces before application of paint etc complete all as specified and directed

M&L for applying one coat of cement base paint on walls including preparation of old decorated surfaces with brooming down smoke soot, moulds, moss and efforescent salts etc complete all as specified and as directed .

Description all as per item No 123 here-in-before but two coats.

M&L for applying one coat of synthetic enamel paint over old painted wooden surfaces of any description over 10cm width or girth including preparation of old surfaces complete all as specified and as directed.

M&L for applying one coat of synthetic enamel paint over old painted steel surfaces of any descripition over 10cm width or girth including preparation of old surfaces complete all as specified and as directed

M&L for preparation of old/new painted concrete surface (as in Chequered tiles, Interlocking tiles, walkway, driverways and terrace floors & kerb stone etc) and apply two coat of floor coat Emulsion paint (ordinary tint) of any description over 10cm girth and width, not otherwise described complete all as specified and as directed.

M&L for preparation of new surfaces of wood and wood based materials of any descriptions not otherwise described over 10Cm width or girth & applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified.

M&L for preparation of new surfaces of Steel and Steel based materials of any descriptions not otherwise described over 10Cm width or girth & applying two coat of synthetic enamel paint over a coat of red oxide on steel surfaces complete all as specified.

S & F pressed steel frames for doors with one or more rebates of size 105x60 mm including necessary fixing lugs, lock strike plate etc complete made out of 1.25 mm thick MS sheet all as spd and directed.

Material & Labour for pressed steel frames for doors of size 125 x 60 mm for doors with one or more rebate incl necessary fixing lugs, hinges, lock, strike plates welded with frame and making arrangement for fixing of door spring etc complete all as specified.

S & F factory made solid PVC door frame size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube as per spacification and directed.

PCC 1:3:6 type C1 using 20mm graded stone aggregate as in filling hollow of pressed steel frame.

S & F factory made solid panel PVC door shutter 30mm the style consisting of frame made out of MS tube, for top & bottom rail, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width struck inside with solvent cement for stiles and plain colour PVC sheet for top rail, bottom rail & lock rail on either side & as gep insert for top rail and bottom rail. panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement as per spacification and directed.

S&F for Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and directed

S&F 35mm thick flush shutter solid core construction with block board core and ply wood face panels commercial type on both sides all as spd and directed.

M&L for preparation of newly plastered or unplastered wall surfaces and applying two coat of acrylic emulsion exterior quality over and including a coat of water based primer (Apex painting) (tint and pattern as approved by GE) complete all as specified. Note:- Paint and primer shall be 1st quality.

M&L for one coats of acrylic exterior emulsion (weather proof) paint on walls ,parapets,facia,soffit of projections and other surface including preparation of old decorated suface by brooming,closing of minor holes,preparation of corners,edges etc by using required putty complete all as specified and directed .

S&F 100mm size butt hinges, medium weight cold rolled mild steel all as spd and directed

S&F 250mm long aluminum alloy anodized sliding door bolt with hasp & staple (bolt type) and fixing clips of sheet cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminum alloy all as spd and directed

S&F in repair kitchen plate rack of size 33" X 31" X 10" made out of 1mm thick stainless steel complete all as spd and directed

M&L for two coats of acrylic exterior emulsion paint on walls ,parapets,facia,soffit of projections and other surface including preparation of old decorated suface by brooming,closing of minor holes,preparation of corners,edges etc by using required primer/putty complete all as specified and directed.

S&F 150 mm long aluminium anodized barrel tower bolt of extruded section all as spd and directed

S&F 150mm size aluminium handles cast type, anodized all as spd and directed

S&F aluminium section powder coated (powder coating not less than 50 micron thick) grill of size 6 x 4.5 mm thick section 10cm centre to centre spacing fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles complete with U-channel all around fixed in window with screws complete all as specified and directed

S&F 12mm thick particle board exterior grade with decorative prelaminated both sides of approved shades fixed to aluminium shutters/ partitions complete all as specified and directed.

S&F anodised aluminium powder coating aluminium section weighing not less than 0.55Kg/m {minimum thickness of powder coating 50 micron)frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed.

S&F 4.8mm thick sheet glass ordinary quality in Squre/rectangle fixed with glazing pins and rubber beading etc in aluminium door/window/partitions etc complete all as specified and directed.

S&F in repairs stainless steel wire cloth 0.56 mm nominal dia of wire and average width of aperture 1.18 mm and fixed with stainless steel wire staple etc in wooden/steel frames complete all as specified and directed.

All as item No. 169.00 here in before but in skirting with and including 10mm thick rendering on fair faces of brickwork in CM 1:4 complete all as specified and directed.

Welding in repair exc.2.5cm but n.exc.5cm in length of metal having thickness n.exc, 6mm complete all as specified and directed.

S&F in repair plywood 4mm thick, grade BWP, type BB fixed with screw to timber frame work complete all as specified and directed

S&F in repair plywood 6mm thick, grade BWP, type BB fixed with screw to timber frame work complete all as specified and directed

S&F in repair 50mm dia brass polished cupboard knobs fixed with nut, screw and washer of mil

d steel, bright finished all as spd and directed

S&F in repair 20mm dia MS CP curtain rods with fixing brackets, stops etc complete all as specified and directed

S&F in repair 2mm thick fibre glass reinforced translucent corrugated sheeting with two corrugation side lap fixed with L-type or J-type or cranked bolts and washer in roof and wall etc all as spd and directed

S&F anodised aluminium Powder coating door shutters aluminium section weighing not less than 0.55Kg/m {minimum thickness of powder coating 50 micron) including necessary joining cleats, glazing clips, ruber neoprene packing , hinges,anodised aluminium snap beading screws,all necessary builders hardware etc complete all as specified and directed.

M&L securing glass of any description in existing steel frame with putty including removing of old putty complete all as specified and directed.

S&F anodised aluminium Powder coating window and ventilator shutters, side hung type without sash bars aluminium section weighing not less tha 0.55Kg/m including necessary joining cleats, glazing clips, ruber neoprene packing , anodised aluminium snap beading screws ,anodised aluminium fittings such as peg stays 150mm long (1no), hinges type B-21 100mm long(2 no.) suitable handle(1 no) including all necessary builders hardare complete all as specified and directed.

M & L for Applying silicon sealeant on joints of wall, cill, jambs roof, window etc. with sufficient quantity for proper sealing of joints complete all as specified and directed.

Taking down and Adjusting / repairing of steel window shutters for smooth opening/closing including greasing, welding and adjustment of projecting type friction hinges in any position make fully functioning complete all as specified and directed.

S&F in repair door closer hydraulically regulated, aluminium body designation No 2, universal type, suitable for door shutter of 701 to 850 mm in width complete all as specified and directed.

M&L brickwork with subclass 'B 'old size bricks straigth or curved on plan exc 6m mean radius built in CM (1:6) cmplete all as specified and directed.

M&L half brick thick brick work with subclass 'B 'old size bricks straigth or curved on plan to radius built in CM (1:4) complete all as specified and directed

Cleaning of exposed concrete surface of sticking material including loose and foreign material by sand blasting with coarse sand followed by and including cleaning with oil free air blast as per direction of Engineer in charge.

Providing mixing and applying bonding coat of approved adhesive on chipped portion of RCC as per specifications and dIrection of Engineer-in-Charge complete in all respect : Epoxy bonding adhesive having coverage 2.20 sqm/kg of approved make

S&F in repair aluminium anodised fully glazed partly panelled partitions and fixed glazing made out of anodized aluminium section 63.50x 38.10 x 1.60mm including necessary jointing cleats glazing clips, rubber packing a

nodised alum snap beading screws etc, frame work fixed to walls , floor and ceiling with rawl plug wherever required complete all as spd and as directed by Engineer-in-Charge (Sheet glass and particle board shall be measured and paid for separately) Note : area of each panel shall not be exc 01 sqm

Chipping of unsound/weak concrete material from slabs, beams, columns etc. with manual Chisel and/ or by standard power driven percussion type or of approved make including tapering of all edges, making square shoulders of cavities including cleaning the exposed concrete surface and reinforcement with wire brushes etc. and disposal of debris for all lead and lifts all complete as per direction of Engineer-In-Charge : 75mm average thickness

Taking down and Adjusting / repairing of Aluminium door/windows shutters, for easy closing/opening tightning of hinges or changing the position of hinges, tightening of Glass/ Particle board by replacing rubber beading and clip packing, adjustments of floor machine for smooth opening and closing and refixing the same complete all as specified and directed.

Supply & fixing as in repair aluminium alloy body floor door stopper of size 75mm having double round legs for better grip ,with rubber base fixed to door shutters with countersunk screws complete all as specified and directed.

M&L Light shade vitrified ceramic tiles 8-9mm thick (Square/Rectangular) polished, area of each tiles upto & including 0.36 Sqm in floors, set and jointed in neat cement slurry and pointed in coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed

Shotcreting R.C.C. columns, beams and slabs etc. in layers with approved design mix concrete having the specified minimum characteristic compressive strength [with ordinary portland cement, coarse sand and graded stone aggregate of 10 mm maximum size in proportion as per design criteria] including the cost of centering and shuttering at edges and corners etc. as directed by Engineerin- Charge : 50mm thick in Grade M 25 with cement content not less than 330 kg per cum Note: Rates shall include the providing necessary ground wires etc. The levelling gauges, if used, shall be paid for separately. Payment under this item shall be made only after proper wet curing has been done and surface has been satisfactorily evaluated by sounding/ tapping with a blunt metal instrument.

M&L joint free non skid ceramic coloured tiles 7-8mm thick (square/rectangular) area of each tile exc 0.06 Sqm but not exc 0.11 Sqm in floor set and jointed in in neat cement slurry and pointed in cloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed