C/o OCR of SIB at Daporijo SH Type II Type III and IV and Multistorey RCC Building

Amount

Type-II 4 units ( Double storey)

I. Earthwork

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning.

II. CC Work

Providing and laying cement concrete 1 : 3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in a) Foundations and plinth

Providing and laying cement concrete 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering in :a) Foundations and plinth

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

III. RCC Work

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in : b) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.b) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with 1 : 1.5 : 3( 1 cement: 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in shelves up to floor two level excluding cost of centering and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for :

a) Foundation, footings, bases of columns etc. and mass concrete.

c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

d) Lintels, beams, girders, bressumers and cantilevers etc.

e) Column, pillars, posts and struts etc.

Reinforcement of RCC work including bending, binding and placing in position complete.b) Tar/TMT Steel

IV. Brick Work

Brick work with best available local bricks in foundation and plinth in cement mortar 1:5 (1 cement : 5 fine sand).

Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth.

Extra for half brick masonry in superstructure above plinth level and up to floor two level.

Aluminium Works

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge. (Cost of aluminium snap beading shall be paid in basic item) 4.1 With float glass panes of 4.0 mm thickness.

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.b) Ornamental grill.

Providing and fixing aluminum sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete.a) 300 x 16 mm

Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete.

Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete.a) 125 mm

VI. Flooring

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622, of approved make , in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 course sand) including grouting the joints with white cement and matching pigments etc, complete. b) size of tiles 600x600mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622, of approved make , in all colours and shades, skirting, riser of steps, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 course sand) including grouting the joints with white cement and matching pigments etc, complete. b) size of tiles 600x600mm

White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry.

VII. Roofing

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately).

Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet roofing fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of purlins, rafters and trusses. Details of cost for 179.655 Sq.m.Laying and fixing 20 sheets in 3 row require Overall sheet area of 20 x 3 x 3.05 x 1.072 plus 3% wastages= 202.061 Sqm After H & L !aping as per manufacturer's specification, effective Area Measurable will be 20 x 3x 2.95 x 1.015 = 179.655 Sqm

Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet ridges fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of pur!ins, rafters and trusses. Details of cost for 11.75m Laying and fixing 4 lenths of 3.05m each require Overall length of 4 x 3.05 plus 3% wastages= 12.566m After laping as per manufacturer's specification, effective Measurable length will be (4 x 3.05)- (3 x 0.15) = 11.75m

False Ceiling

Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling.a) Best local approved quality wood.

Extra for chamfered edges in beading

VII. Finishing

12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).

15mm cement plaster 1:5 (1 cement : 5 fine sand) on the rough side of single or half brick wall

6 mm cement plaster to ceiling 1 : 4 (1 cement: 4 fine sand).

Applying one coat of cemenl primer of approved brand and manufacture on wall surface.

Painting two or more coats with enamel paint of approved brand and manufacture in any shade on new work to give an even shade.

Distempering (lwo or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.

VIII. Miscelleneous

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

X. Water Supply

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).a) 15 mm nominal bore

b) 20 mm nominal bore.Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work).

a) 15 mm nominal bore

b) 20 mm nominal bore

d) 32 mm nominal bore

Providing and fixing brass bib cock of approved quality.a)15 mm nominal bore

Providing and fixing brass stop cock of approved quality.a) 15 mm nominal bore

XI. Sanitary Installations

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.

a) Long Pan patten WC Pan

Providing and fixing white vitreous china pedestal type (European type WC pan) water closet with seat and lid with CP brass hinges and rubber buffers, 12.5 Litres white vitreous china low-level flushing cistern with fittings and brackets 40 mm white porcelain in enamel led flush band, 20 mm over flow pipe with specials and mosquito proof coupling of approved municipal design complete including cutting and making good the walls and floors where required.

a) WC pan with white plastic seat and lid.

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.

b) Flat back wash basin size 550x400 mm with single 15 mm CP brass pillar taps of heavy quality.

Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC.

a) 250 x 130 x 30 mm

Providing and fixing 12.5 litres high level CI flushing cistern of approved make with integral fittings such as ball valve, bell, lever, GI chain and pull complete.

Providing and fixing kitchen sink including making all connection excluding cost of fittings. a) White glazed fire clay sink size 600x450x150 mm

Providing and fixing CP Brass Chain and rubber plug complete for sink or wash basins.

Providing and fixing CP brass waste for wash basins and sinks. B)40 mm dia

Providing and fixing 100 mm sand cast iron grating for gulley, fioors or nahni trap.

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.

Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality). a) 750 x 20 mm size

Providing and fixing toilet paper holder. a) CP Brass

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.

a) 100 mm dia

c) 50 mm dia

Providing and fixing UPVC/PVC heel rest sanitary bend.

a) 100 mm dia

c )50 mm dia

Providing and fixing PVC single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

a) 100 x 100 x 100 mm

Providing and fixing PVC trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors.

c) 100 mm inlet and 50 mm outlet

Cost for internal electrification

POINT WIRING

Supply, Installation, testing and commissioning Conduit wiring for lights/ fan socket outlets as per the mode of measurements described in the specifications consisting of - a) Wiring in 25/20 mm Dia 2mm thick HMS ,MMS type of PVC conduit as required. b) 1100V grade PVC insulated Cu FR Wire. c) Insulated or base protective earth d) 1.6 mm thick Outlet boxes and junction box as per manufacturers standard e) All work & materials necessary for wiring a point circuit of any length from the Final Distribution Board to switch board, except where identified. f) Embedding/surface conduits and accessories in walls and floors etc. during construction and / or cutting chases (with chase cutting machine) and making good with finishing of wall after embedding of conduit on walls. g) Switch, socket outlet and necessary blank plates, Face-Plates etc. as required. f) All shuttered type sockets with earth terminal. SITC of moduller type Switch, Sockets ,Faceplates , 1.6 mm thick G.I Back Boxes in walls by Electrical Contractor. Colour / Shade / Type of all switch-socket to be as per the Client / Architech confirmation.

Wiring for primary points from SB to first light point with 3X1.5 sq. mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket, modular plate, suitable GI box Average=5 mtr

Wiring for secondary light point with 3x1.5sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core wire etc as required. Average=3 mtr

Wiring for 16amp 3/5 pin socket outlet Control By 16A switch x 2nos on Same Board independent Location with 2X2.5 sq.mm + 1x 1.5sqmm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box. Average=8 mtr

Wiring for 16amp 3/5 pin socket outlet Control By 16A switch x 1nos on Same Board independent Location with 2X2.5 sq.mm + 1x 1.5sqmm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box. Average=8 mtr

Wiring for Two Nos 6amp, 3/5 pin socket outlet Control By Two Nos 6A switch on Same Board independent Location with 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch,socket, modular plate, suitable GI box. Average=4 mtr

Wiring for 1 Nos 6amp, 3/5 pin socket outlet Control By 1 Nos 6A switch on Same Board independent Location with 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch,socket, modular plate, suitable GI box. Average=4 mtr

Wiring for 1 Nos 6amp, 3/5 pin socket outlet Control By 1 Nos 6A switch on lighting switch board with 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch,socket, modular plate, suitable GI box. Average=0.5 mtr

Wiring for SB to fan point with 3X1.5 sq. mmPVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, fan regulator, modular plate, suitable GI box and 3" deep fan box with hook (conduit & fan cost should be excluded) Average=6 mtr

Wiring for SB to exhuast fan point with 3X1.5 sq. mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit , with modular switch, socket, modular plate, suitable GI box.

Wiring from DB to switch board (submain) wiring alongwith necessary earth wire for the following sizes of PVC insulated copper FRLS wire concealed in HMS class PVC conduit conductor, already laid concealed HMS class PVC conduit as required. (only wiring)

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 1.5 sq. mm earth wire

Supplying and fixing of following sizes of HMS class PVC conduit along with accessories in concealed/surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

LOW VOLTAGE WIRING

LV Wires

Supply, Installation, testing and commissioning Indoors PVC insulated LV Wires on walls, ceiling, cable trays complete with clamps Termination etc

CAT 6 cable data including terminations in already laid conduits.

For Telophone including terminations in already laid conduits. 2 pair 0.5mm

RG -6 cable for TV outlet including terminations in already laid conduit.

RG -11 cable for TV outlet including terminations in already laid conduit.

LV Cables

Supply, Installation, testing and commissioning Indoors multipair 0.5mm dia copper PVC insulated and sheathed, armoured telephone cables on walls, ceiling, cable trays complete with clamps Termination, cable markers etc. from MDF to the various tag blocks as specified and shown on drawings.

10 pair 0.5 mm twisted pair non jelly filled armoured telephone cable

20 pair 0.5 mm twisted pair non jelly filled armoured telephone cable

50 pair 0.5 mm twisted pair non jelly filled armoured telephone cable

100 pair 0.5 mm twisted pair non jelly filled armoured telephone cable

Supplying and fixing of following sizes of HMS class PVC conduit along with accessories in concealed/surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

LT CABLING SYSTEM

POWER CABLES

Supply and laying heavy duty 1100V grade XLPE insulated sheathed & armoured FRLS cables indoor or outdoor with Cu conductors as specified and shown on drgs. and as per IS 7098- part 1 of 1998 complete with:- a) Cable clamps on walls, columns, beams, cable markers etc. Cable Dressing on Trays,Trenches & HDPE Pipes b) Earthing the glands armouring etc. c) Aluminium tags for all XLPE Al/ Cu cables to be provided.

4c x 1.5sq.mm Cu XLPE Cable

4c x 2.5sq.mm Cu XLPE Cable

4c x 4sq.mm Cu XLPE Cable

TERMINATIONS WITH SINGLE COMPRESSION GLANDS,LUGS & ACCESSORIES

4c x 1.5sq.mm Cu XLPE Cable

4c x 2.5sq.mm Cu XLPE Cable

4c x 4sq.mm Cu XLPE Cable

3c x 4sq.mm Cu XLPE Cable

4c x 6sq.mm Cu XLPE Cable

4c x 10sq.mm Cu XLPE Cable

Supply and laying heavy duty 1100V grade XLPE insulated sheathed & armoured FRLS cables indoor or outdoor with AL conductors as specified and shown on drgs. and as per IS 7098- part 1 of 1998 complete with:- a) Cable clamps on walls, columns, beams, cable markers etc. Cable Dressing on Trays,Trenches & HDPE Pipes b) Earthing the glands armouring etc. c) Aluminium tags for all XLPE Al/ Cu cables to be provided.

3.5C x 120sq.mm AL XLPE Cable

3.5C x 70sq.mm AL XLPE Cable

3.5C x 50sq.mm AL XLPE Cable

3.5C x 35sq.mm AL XLPE Cable

CABLE TRAY

300 mm width X 50 mm depth X 2 mm thickness (perforated )

150 mm width X 50 mm depth X 2 mm thickness ( Perforated )

LIGHTING FIXTURES AND FANS

Supply, Installation, testing and commissioning of following light fixtures and fans as per drawings and specifications with all other accessories. The rate shall include all accessories required to complete the installation as required, Earthing of fittings & Connections from the ceiling rose or junction box of the fitting including Flexible Wires,hangers,chains Complete in all respect.

LED 18 W round shape Cielling Mounted

LED 30 W square shape Cielling Mounted 300 x 300mm

80W Cielling Mounted Fan 1200mm Dia

Door bell

Electric 5.5 L Instant Water Geyser | High Grade SS Tank

Exhaust Fan 6 inch Ventilation Fan Pure Copper Motor 150 mm

COMMON AREA/STAIRCASE/LOBBY ETC.

Primary Light points Lift lobby in 25mm conduit Average-12mtr

Secondary Light points in 25mm conduit Average-3 mtr

PANELS & DISTRIBUTION BOARDS

Supply, installation, testing and commissioning of cubicle type panels of 14 SWG CRCA sheet steel floor mounted totally enclosed with top and bottom cable entry and suitable for use on 433 V 3 phase 4 wire 50 c/s having 35 KA fault capacity complete and housed with Aluminium/copper bus bar equipments and their accessories including supply and fixing of base channels of 100x50x6mm as required and with following incoming and outgoing switchgear with protection, metering etc. complete as required and as per specification and schematic diagram.

6 WAY TPN-DB LDB

12 WAY SPN GR Floor

EARTHING SYSTEM

Chemical earthing 17,2mm dia 3 mtr long with 50kg BFC Compound With brick workchamber 300 x 300mm

25 x 6 mm G.I.

25 x 3 mm G.I.

8 SWG G.I earth wires

8 SWG Cu earth wires

Add Septic Tank(100 User)

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning t

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Providing and laying cement concrete 1 : 3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in a) Foundations and plinth

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.

a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for :

a) Foundation, footings, bases of columns etc. and mass concrete.

c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

Reinforcement of RCC work including bending, binding and placing in position complete.

b) Tar/TMT Steel

Brick work with best available local bricks in foundation and plinth in cement mortar 1:3 (1 cement : 3 fine sand).

40 mm thick red oxide flooring, under layer of 30 mm thick cement concrete 1 : 2 : 4 (1cement: 2 coarse sand : 4 stone aggregate 12.5 mm nominal size) & top layer of 10 mm thick plaster of cement red oxide mix (using 3.5 kg of red oxide of iron per 50 kg of cement) 1 : 3 (1 cement red oxide mix : 3 coarse sand) finished with a floating coat of neat cement red oxide mix of same proportion.

Cement plaster skirting (up to 30 cm height) with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, including rounding of junctions with floor. a) 18 mm thick

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.

a) 100 mm dia

Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft and SW drain pipe 100 mmdia 1.80 m long complete,as per standard design.

Furniture

Type-III 4 units(Double storey)

I. Earthwork

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning .

II. CC Work

Providing and laying cement concrete 1 : 3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in a) Foundations and plinth

Providing and laying cement concrete 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering in :

a) Foundations and plinth

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

III. RCC Work

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in :

b) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.

a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.

b) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with 1 : 1.5 : 3( 1 cement: 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in shelves up to floor two level excluding cost of centering and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for :

a) Foundation, footings, bases of columns etc. and mass concrete.

c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

d) Lintels, beams, girders, bressumers and cantilevers etc.

e) Column, pillars, posts and struts etc.

Reinforcement of RCC work including bending, binding and placing in position complete.

b) Tar/TMT Steel

IV. Brick Work

Brick work with best available local bricks in foundation and plinth in cement mortar 1:5 (1 cement : 5 fine sand).

Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth.

Extra for half brick masonry in superstructure above plinth level and up to floor two level.

Aluminium Works

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge. (Cost of aluminium snap beading shall be paid in basic item) 4.1 With float glass panes of 4.0 mm thickness.

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.

b) Ornamental grill.

Providing and fixing aluminum sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete.

Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete.

Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete.

VI. Flooring

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622, of approved make , in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 course sand) including grouting the joints with white cement and matching pigments etc, complete. b) size of tiles 600x600mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622, of approved make , in all colours and shades, skirting, riser of steps, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 course sand) including grouting the joints with white cement and matching pigments etc, complete. b) size of tiles 600x600mm

White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry.

VII. Roofing

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately).

Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet roofing fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of purlins, rafters and trusses. Details of cost for 179.655 Sq.m.Laying and fixing 20 sheets in 3 row require Overall sheet area of 20 x 3 x 3.05 x 1.072 plus 3% wastages= 202.061 Sqm After H & L !aping as per manufacturer's specification, effective Area Measurable will be 20 x 3x 2.95 x 1.015 = 179.655 Sqm

Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet ridges fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of pur!ins, rafters and trusses. Details of cost for 11.75m Laying and fixing 4 lenths of 3.05m each require Overall length of 4 x 3.05 plus 3% wastages= 12.566m After laping as per manufacturer's specification, effective Measurable length will be (4 x 3.05)- (3 x 0.15) = 11.75m

False Ceiling

Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling.

a) Best local approved quality wood.

Extra for chamfered edges in beading

VII. Finishing

12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).

15mm cement plaster 1:5 (1 cement : 5 fine sand) on the rough side of single or half brick wall

6 mm cement plaster to ceiling 1 : 4 (1 cement: 4 fine sand).

Applying one coat of cemenl primer of approved brand and manufacture on wall surface.

Painting two or more coats with enamel paint of approved brand and manufacture in any shade on new work to give an even shade.

Distempering (lwo or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.

VIII. Miscelleneous

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

X. Water Supply

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).

a) 15 mm nominal bore

b) 20 mm nominal bore

Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work).

a) 15 mm nominal bore

b) 20 mm nominal bore

d) 32 mm nominal bore

Providing and fixing brass bib cock of approved quality.

a)15 mm nominal bore

Providing and fixing brass stop cock of approved quality.

a) 15 mm nominal bore

XI. Sanitary Installations

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.

a) Long Pan patten WC Pan

Providing and fixing white vitreous china pedestal type (European type WC pan) water closet with seat and lid with CP brass hinges and rubber buffers, 12.5 Litres white vitreous china low-level flushing cistern with fittings and brackets 40 mm white porcelain in enamel led flush band, 20 mm over flow pipe with specials and mosquito proof coupling of approved municipal design complete including cutting and making good the walls and floors where required.

a) WC pan with white plastic seat and lid.

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.

b) Flat back wash basin size 550x400 mm with single 15 mm CP brass pillar taps of heavy quality.

Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC.

a) 250 x 130 x 30 mm

Providing and fixing 12.5 litres high level CI flushing cistern of approved make with integral fittings such as ball valve, bell, lever, GI chain and pull complete.

Providing and fixing kitchen sink including making all connection excluding cost of fittings. a) White glazed fire clay sink size 600x450x150 mm

Providing and fixing CP Brass Chain and rubber plug complete for sink or wash basins.

Providing and fixing CP brass waste for wash basins and sinks. B)40 mm dia

Providing and fixing 100 mm sand cast iron grating for gulley, fioors or nahni trap.

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.

Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality). a) 750 x 20 mm size

Providing and fixing toilet paper holder. a) CP Brass

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.

a) 100 mm dia

c) 50 mm dia

Providing and fixing UPVC/PVC heel rest sanitary bend.

a) 100 mm dia

c )50 mm dia

Providing and fixing PVC single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

a) 100 x 100 x 100 mm

Providing and fixing PVC trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors.

c) 100 mm inlet and 50 mm outlet

Cost for internal electrification

POINT WIRING

Supply, Installation, testing and commissioning Conduit wiring for lights/ fan socket outlets as per the mode of measurements described in the specifications consisting of - a) Wiring in 25/20 mm Dia 2mm thick HMS ,MMS type of PVC conduit as required. b) 1100V grade PVC insulated Cu FR Wire. c) Insulated or base protective earth d) 1.6 mm thick Outlet boxes and junction box as per manufacturers standard e) All work & materials necessary for wiring a point circuit of any length from the Final Distribution Board to switch board, except where identified. f) Embedding/surface conduits and accessories in walls and floors etc. during construction and / or cutting chases (with chase cutting machine) and making good with finishing of wall after embedding of conduit on walls. g) Switch, socket outlet and necessary blank plates, Face-Plates etc. as required. f) All shuttered type sockets with earth terminal. SITC of moduller type Switch, Sockets ,Faceplates , 1.6 mm thick G.I Back Boxes in walls by Electrical Contractor. Colour / Shade / Type of all switch-socket to be as per the Client / Architech confirmation.

Wiring for primary points from SB to first light point with 3X1.5 sq. mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket, modular plate, suitable GI box Average=5 mtr

Wiring for secondary light point with 3x1.5sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core wire etc as required. Average=3 mtr

Wiring for 16amp 3/5 pin socket outlet Control By 16A switch x 2nos on Same Board independent Location with 2X2.5 sq.mm + 1x 1.5sqmm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box. Average=8 mtr

Wiring for 16amp 3/5 pin socket outlet Control By 16A switch x 1nos on Same Board independent Location with 2X2.5 sq.mm + 1x 1.5sqmm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box. Average=8 mtr

Wiring for Two Nos 6amp, 3/5 pin socket outlet Control By Two Nos 6A switch on Same Board independent Location with 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch,socket, modular plate, suitable GI box. Average=4 mtr

Wiring for 1 Nos 6amp, 3/5 pin socket outlet Control By 1 Nos 6A switch on Same Board independent Location with 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch,socket, modular plate, suitable GI box. Average=4 mtr

Wiring for 1 Nos 6amp, 3/5 pin socket outlet Control By 1 Nos 6A switch on lighting switch board with 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch,socket, modular plate, suitable GI box. Average=0.5 mtr

Wiring for SB to fan point with 3X1.5 sq. mmPVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, fan regulator, modular plate, suitable GI box and 3" deep fan box with hook (conduit & fan cost should be excluded) Average=6 mtr

Wiring for SB to exhuast fan point with 3X1.5 sq. mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit , with modular switch, socket, modular plate, suitable GI box.

Wiring from DB to switch board (submain) wiring alongwith necessary earth wire for the following sizes of PVC insulated copper FRLS wire concealed in HMS class PVC conduit conductor, already laid concealed HMS class PVC conduit as required. (only wiring)

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 4.0 sq. mm + 1 X 2.5 sq. mm earth wire

2 x 6.0 sq.mm + 1 X 4 sq.mm earthg wire

Supplying and fixing of following sizes of HMS class PVC conduit along with accessories in concealed/surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

LOW VOLTAGE WIRING

LV Wires

Supply, Installation, testing and commissioning Indoors PVC insulated LV Wires on walls, ceiling, cable trays complete with clamps Termination etc

CAT 6 cable data including terminations in already laid conduits.

For Telophone including terminations in already laid conduits. 2 pair 0.5mm

RG -6 cable for TV outlet including terminations in already laid conduit.

RG -11 cable for TV outlet including terminations in already laid conduit.

LV Cables

Supply, Installation, testing and commissioning Indoors multipair 0.5mm dia copper PVC insulated and sheathed, armoured telephone cables on walls, ceiling, cable trays complete with clamps Termination, cable markers etc. from MDF to the various tag blocks as specified and shown on drawings.

10 pair 0.5 mm twisted pair non jelly filled armoured telephone cable

20 pair 0.5 mm twisted pair non jelly filled armoured telephone cable

50 pair 0.5 mm twisted pair non jelly filled armoured telephone cable

100 pair 0.5 mm twisted pair non jelly filled armoured telephone cable

Supplying and fixing of following sizes of HMS class PVC conduit along with accessories in concealed/surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

TTB box with 20 pair krone

LT CABLING SYSTEM

POWER CABLES

Supply and laying heavy duty 1100V grade XLPE insulated sheathed & armoured FRLS cables indoor or outdoor with Cu conductors as specified and shown on drgs. and as per IS 7098- part 1 of 1998 complete with:- a) Cable clamps on walls, columns, beams, cable markers etc. Cable Dressing on Trays,Trenches & HDPE Pipes b) Earthing the glands armouring etc. c) Aluminium tags for all XLPE Al/ Cu cables to be provided.

4c x 1.5sq.mm Cu XLPE Cable

4c x 2.5sq.mm Cu XLPE Cable

4c x 4sq.mm Cu XLPE Cable

3c x 4sq.mm Cu XLPE Cable

TERMINATIONS WITH SINGLE COMPRESSION GLANDS,LUGS & ACCESSORIES

4c x 1.5sq.mm Cu XLPE Cable

4c x 2.5sq.mm Cu XLPE Cable

4c x 4sq.mm Cu XLPE Cable

3c x 4sq.mm Cu XLPE Cable

4c x 6sq.mm Cu XLPE Cable

4c x 10sq.mm Cu XLPE Cable

Supply and laying heavy duty 1100V grade XLPE insulated sheathed & armoured FRLS cables indoor or outdoor with AL conductors as specified and shown on drgs. and as per IS 7098- part 1 of 1998 complete with:- a) Cable clamps on walls, columns, beams, cable markers etc. Cable Dressing on Trays,Trenches & HDPE Pipes b) Earthing the glands armouring etc. c) Aluminium tags for all XLPE Al/ Cu cables to be provided.

3.5C x 120sq.mm AL XLPE Cable

3.5C x 70sq.mm AL XLPE Cable

3.5C x 50sq.mm AL XLPE Cable

3.5C x 35sq.mm AL XLPE Cable

CABLE TRAY

450 mm width X 50 mm depth X 2.0 mm thickness ( Ladder )

300 mm width X 50 mm depth X 2 mm thickness (perforated )

150 mm width X 50 mm depth X 2 mm thickness ( Perforated )

LIGHTING FIXTURES AND FANS

Supply, Installation, testing and commissioning of following light fixtures and fans as per drawings and specifications with all other accessories. The rate shall include all accessories required to complete the installation as required, Earthing of fittings & Connections from the ceiling rose or junction box of the fitting including Flexible Wires,hangers,chains Complete in all respect.

LED 18 W round shape Cielling Mounted

LED 30 W square shape Cielling Mounted 300 x 300mm

80W Cielling Mounted Fan 1200mm Dia

Door bell

Electric 5.5 L Instant Water Geyser | High Grade SS Tank

Exhaust Fan 6 inch Ventilation Fan Pure Copper Motor 150 mm

COMMON AREA/STAIRCASE/LOBBY ETC.

Primary Light points Lift lobby in 25mm conduit Average-12mtr

Secondary Light points in 25mm conduit Average-3 mtr

Add Septic Tank(100 User)

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning t

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Providing and laying cement concrete 1 : 3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in a) Foundations and plinth

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.

a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for :

a) Foundation, footings, bases of columns etc. and mass concrete.

c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

Reinforcement of RCC work including bending, binding and placing in position complete.

b) Tar/TMT Steel

Brick work with best available local bricks in foundation and plinth in cement mortar 1:3 (1 cement : 3 fine sand).

40 mm thick red oxide flooring, under layer of 30 mm thick cement concrete 1 : 2 : 4 (1cement: 2 coarse sand : 4 stone aggregate 12.5 mm nominal size) & top layer of 10 mm thick plaster of cement red oxide mix (using 3.5 kg of red oxide of iron per 50 kg of cement) 1 : 3 (1 cement red oxide mix : 3 coarse sand) finished with a floating coat of neat cement red oxide mix of same proportion.

Cement plaster skirting (up to 30 cm height) with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, including rounding of junctions with floor. a) 18 mm thick

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.

a) 100 mm dia

Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft and SW drain pipe 100 mmdia 1.80 m long complete,as per standard design.

Furniture

Type-IV (Single storey)

I. Earthwork

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning ....

II. CC Work

Providing and laying cement concrete 1 : 3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in a) Foundations and plinth

Providing and laying cement concrete 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering in :

a) Foundations and plinth

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

III. RCC Work

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in :

b) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.

a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.

b) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with 1 : 1.5 : 3( 1 cement: 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in shelves up to floor two level excluding cost of centering and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for :

a) Foundation, footings, bases of columns etc. and mass concrete.

c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

d) Lintels, beams, girders, bressumers and cantilevers etc.

e) Column, pillars, posts and struts etc.

Reinforcement of RCC work including bending, binding and placing in position complete.

b) Tar/TMT Steel

IV. Brick Work

Brick work with best available local bricks in foundation and plinth in cement mortar 1:5 (1 cement : 5 fine sand).

Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth.

Extra for half brick masonry in superstructure above plinth level and up to floor two level.

Aluminium Works

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge. (Cost of aluminium snap beading shall be paid in basic item) 4.1 With float glass panes of 4.0 mm thickness.

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.

b) Ornamental grill.

Providing and fixing aluminum sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete.

Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete.

Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete.

VI. Flooring

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622, of approved make , in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 course sand) including grouting the joints with white cement and matching pigments etc, complete. b) size of tiles 600x600mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622, of approved make , in all colours and shades, skirting, riser of steps, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 course sand) including grouting the joints with white cement and matching pigments etc, complete. b) size of tiles 600x600mm

White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry.

VII. Roofing

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately).

Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet roofing fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of purlins, rafters and trusses. Details of cost for 179.655 Sq.m.Laying and fixing 20 sheets in 3 row require Overall sheet area of 20 x 3 x 3.05 x 1.072 plus 3% wastages= 202.061 Sqm After H & L !aping as per manufacturer's specification, effective Area Measurable will be 20 x 3x 2.95 x 1.015 = 179.655 Sqm

Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet ridges fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of pur!ins, rafters and trusses. Details of cost for 11.75m Laying and fixing 4 lenths of 3.05m each require Overall length of 4 x 3.05 plus 3% wastages= 12.566m After laping as per manufacturer's specification, effective Measurable length will be (4 x 3.05)- (3 x 0.15) = 11.75m

False Ceiling

Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling.

a) Best local approved quality wood.

Extra for chamfered edges in beading

VII. Finishing

12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).

15mm cement plaster 1:5 (1 cement : 5 fine sand) on the rough side of single or half brick wall

6 mm cement plaster to ceiling 1 : 4 (1 cement: 4 fine sand).

Applying one coat of cemenl primer of approved brand and manufacture on wall surface.

Painting two or more coats with enamel paint of approved brand and manufacture in any shade on new work to give an even shade.

Distempering (lwo or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.

X. Water Supply

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).

a) 15 mm nominal bore

b) 20 mm nominal bore

Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work).

a) 15 mm nominal bore

b) 20 mm nominal bore

d) 32 mm nominal bore

Providing and fixing brass bib cock of approved quality.

a)15 mm nominal bore

Providing and fixing brass stop cock of approved quality.

a) 15 mm nominal bore

XI. Sanitary Installations

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.

a) Long Pan patten WC Pan

Providing and fixing white vitreous china pedestal type (European type WC pan) water closet with seat and lid with CP brass hinges and rubber buffers, 12.5 Litres white vitreous china low-level flushing cistern with fittings and brackets 40 mm white porcelain in enamel led flush band, 20 mm over flow pipe with specials and mosquito proof coupling of approved municipal design complete including cutting and making good the walls and floors where required.

a) WC pan with white plastic seat and lid.

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.

b) Flat back wash basin size 550x400 mm with single 15 mm CP brass pillar taps of heavy quality.

Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC.

a) 250 x 130 x 30 mm

Providing and fixing 12.5 litres high level CI flushing cistern of approved make with integral fittings such as ball valve, bell, lever, GI chain and pull complete.

Providing and fixing kitchen sink including making all connection excluding cost of fittings. a) White glazed fire clay sink size 600x450x150 mm

Providing and fixing CP Brass Chain and rubber plug complete for sink or wash basins.

Providing and fixing CP brass waste for wash basins and sinks. B)40 mm dia

Providing and fixing 100 mm sand cast iron grating for gulley, fioors or nahni trap.

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.

Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality). a) 750 x 20 mm size

Providing and fixing toilet paper holder. a) CP Brass

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.

a) 100 mm dia

c) 50 mm dia

Providing and fixing UPVC/PVC heel rest sanitary bend.

a) 100 mm dia

c )50 mm dia

Providing and fixing PVC single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

a) 100 x 100 x 100 mm

Providing and fixing PVC trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors.

c) 100 mm inlet and 50 mm outlet

Cost for internal electrification

POINT WIRING

Supply, Installation, testing and commissioning Conduit wiring for lights/ fan socket outlets as per the mode of measurements described in the specifications consisting of - a) Wiring in 25/20 mm Dia 2mm thick HMS ,MMS type of PVC conduit as required. b) 1100V grade PVC insulated Cu FR Wire. c) Insulated or base protective earth d) 1.6 mm thick Outlet boxes and junction box as per manufacturers standard e) All work & materials necessary for wiring a point circuit of any length from the Final Distribution Board to switch board, except where identified. f) Embedding/surface conduits and accessories in walls and floors etc. during construction and / or cutting chases (with chase cutting machine) and making good with finishing of wall after embedding of conduit on walls. g) Switch, socket outlet and necessary blank plates, Face-Plates etc. as required. f) All shuttered type sockets with earth terminal. SITC of moduller type Switch, Sockets ,Faceplates , 1.6 mm thick G.I Back Boxes in walls by Electrical Contractor. Colour / Shade / Type of all switch-socket to be as per the Client / Architech confirmation.

Wiring for primary points from SB to first light point with 3X1.5 sq. mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket, modular plate, suitable GI box Average=5 mtr

Wiring for secondary light point with 3x1.5sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core wire etc as required. Average=3 mtr

Wiring for 16amp 3/5 pin socket outlet Control By 16A switch x 2nos on Same Board independent Location with 2X2.5 sq.mm + 1x 1.5sqmm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box. Average=8 mtr

Wiring for 16amp 3/5 pin socket outlet Control By 16A switch x 1nos on Same Board independent Location with 2X2.5 sq.mm + 1x 1.5sqmm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box. Average=8 mtr

Wiring for Two Nos 6amp, 3/5 pin socket outlet Control By Two Nos 6A switch on Same Board independent Location with 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch,socket, modular plate, suitable GI box. Average=4 mtr

Wiring for 1 Nos 6amp, 3/5 pin socket outlet Control By 1 Nos 6A switch on Same Board independent Location with 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch,socket, modular plate, suitable GI box. Average=4 mtr

Wiring for 1 Nos 6amp, 3/5 pin socket outlet Control By 1 Nos 6A switch on lighting switch board with 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch,socket, modular plate, suitable GI box. Average=0.5 mtr

Wiring for SB to fan point with 3X1.5 sq. mmPVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, fan regulator, modular plate, suitable GI box and 3" deep fan box with hook (conduit & fan cost should be excluded) Average=6 mtr

Wiring for SB to exhuast fan point with 3X1.5 sq. mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit , with modular switch, socket, modular plate, suitable GI box.

Wiring from DB to switch board (submain) wiring alongwith necessary earth wire for the following sizes of PVC insulated copper FRLS wire concealed in HMS class PVC conduit conductor, already laid concealed HMS class PVC conduit as required. (only wiring)

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 4.0 sq. mm + 1 X 2.5 sq. mm earth wire

2 x 6.0 sq.mm + 1 X 4 sq.mm earthg wire

Supplying and fixing of following sizes of HMS class PVC conduit along with accessories in concealed/surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

LOW VOLTAGE WIRING

LV Wires

Supply, Installation, testing and commissioning Indoors PVC insulated LV Wires on walls, ceiling, cable trays complete with clamps Termination etc

CAT 6 cable data including terminations in already laid conduits.

For Telophone including terminations in already laid conduits. 2 pair 0.5mm

RG -6 cable for TV outlet including terminations in already laid conduit.

RG -11 cable for TV outlet including terminations in already laid conduit.

LV Cables

Supply, Installation, testing and commissioning Indoors multipair 0.5mm dia copper PVC insulated and sheathed, armoured telephone cables on walls, ceiling, cable trays complete with clamps Termination, cable markers etc. from MDF to the various tag blocks as specified and shown on drawings.

10 pair 0.5 mm twisted pair non jelly filled armoured telephone cable

20 pair 0.5 mm twisted pair non jelly filled armoured telephone cable

50 pair 0.5 mm twisted pair non jelly filled armoured telephone cable

100 pair 0.5 mm twisted pair non jelly filled armoured telephone cable

Supplying and fixing of following sizes of HMS class PVC conduit along with accessories in concealed/surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

TTB box with 20 pair krone

LT CABLING SYSTEM

POWER CABLES

Supply and laying heavy duty 1100V grade XLPE insulated sheathed & armoured FRLS cables indoor or outdoor with Cu conductors as specified and shown on drgs. and as per IS 7098- part 1 of 1998 complete with:- a) Cable clamps on walls, columns, beams, cable markers etc. Cable Dressing on Trays,Trenches & HDPE Pipes b) Earthing the glands armouring etc. c) Aluminium tags for all XLPE Al/ Cu cables to be provided.

4c x 1.5sq.mm Cu XLPE Cable

4c x 2.5sq.mm Cu XLPE Cable

4c x 4sq.mm Cu XLPE Cable

3c x 4sq.mm Cu XLPE Cable

4c x 6sq.mm Cu XLPE Cable

TERMINATIONS WITH SINGLE COMPRESSION GLANDS,LUGS & ACCESSORIES

4c x 1.5sq.mm Cu XLPE Cable

4c x 2.5sq.mm Cu XLPE Cable

4c x 4sq.mm Cu XLPE Cable

3c x 4sq.mm Cu XLPE Cable

4c x 6sq.mm Cu XLPE Cable

4c x 10sq.mm Cu XLPE Cable

Supply and laying heavy duty 1100V grade XLPE insulated sheathed & armoured FRLS cables indoor or outdoor with AL conductors as specified and shown on drgs. and as per IS 7098- part 1 of 1998 complete with:- a) Cable clamps on walls, columns, beams, cable markers etc. Cable Dressing on Trays,Trenches & HDPE Pipes b) Earthing the glands armouring etc. c) Aluminium tags for all XLPE Al/ Cu cables to be provided.

3.5C x 120sq.mm AL XLPE Cable

3.5C x 70sq.mm AL XLPE Cable

3.5C x 50sq.mm AL XLPE Cable

3.5C x 35sq.mm AL XLPE Cable

3.5C x 50sq.mm AL XLPE Cable

3.5C x 35sq.mm AL XLPe Cable

CABLE TRAY

450 mm width X 50 mm depth X 2.0 mm thickness ( Ladder )

300 mm width X 50 mm depth X 2 mm thickness (perforated )

150 mm width X 50 mm depth X 2 mm thickness ( Perforated )

LIGHTING FIXTURES AND FANS

Supply, Installation, testing and commissioning of following light fixtures and fans as per drawings and specifications with all other accessories. The rate shall include all accessories required to complete the installation as required, Earthing of fittings & Connections from the ceiling rose or junction box of the fitting including Flexible Wires,hangers,chains Complete in all respect.

LED 18 W round shape Cielling Mounted

LED 30 W square shape Cielling Mounted 300 x 300mm

80W Cielling Mounted Fan 1200mm Dia

Door bell

Electric 5.5 L Instant Water Geyser | High Grade SS Tank

Exhaust Fan 6 inch Ventilation Fan Pure Copper Motor 150 mm

COMMON AREA/STAIRCASE/LOBBY ETC.

Primary Light points Lift lobby in 25mm conduit Average-12mtr

Secondary Light points in 25mm conduit Average-3 mtr

PANELS & DISTRIBUTION BOARDS

Supply, installation, testing and commissioning of cubicle type panels of 14 SWG CRCA sheet steel floor mounted totally enclosed with top and bottom cable entry and suitable for use on 433 V 3 phase 4 wire 50 c/s having 35 KA fault capacity complete and housed with Aluminium/copper bus bar equipments and their accessories including supply and fixing of base channels of 100x50x6mm as required and with following incoming and outgoing switchgear with protection, metering etc. complete as required and as per specification and schematic diagram.

6 WAY TPN-DB LDB

12 WAY SPN GR Floor

Add Carrying charges

Add Septic Tank(100 User)

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning t

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Providing and laying cement concrete 1 : 3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in a) Foundations and plinth

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.

a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for :

a) Foundation, footings, bases of columns etc. and mass concrete.

c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

Reinforcement of RCC work including bending, binding and placing in position complete.

b) Tar/TMT Steel

Brick work with best available local bricks in foundation and plinth in cement mortar 1:3 (1 cement : 3 fine sand).

40 mm thick red oxide flooring, under layer of 30 mm thick cement concrete 1 : 2 : 4 (1cement: 2 coarse sand : 4 stone aggregate 12.5 mm nominal size) & top layer of 10 mm thick plaster of cement red oxide mix (using 3.5 kg of red oxide of iron per 50 kg of cement) 1 : 3 (1 cement red oxide mix : 3 coarse sand) finished with a floating coat of neat cement red oxide mix of same proportion.

Cement plaster skirting (up to 30 cm height) with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, including rounding of junctions with floor. a) 18 mm thick

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.

a) 100 mm dia

Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft and SW drain pipe 100 mmdia 1.80 m long complete,as per standard design.

Add Carrying Charges

Furniture

Double storey Office Building

I. Earthwork

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning ....

II. CC Work

Providing and laying cement concrete 1 : 3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in a) Foundations and plinth

Providing and laying cement concrete 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 40 mm nominal size) excluding the cost of centring and shuttering in :

a) Foundations and plinth

Filling in plinth with sand under floors including watering, ramming, consolidating and dressing complete.

III. RCC Work

Reinforced concrete work in foundations, footings, bases of columns etc. and mass concrete excluding cost of centring, shuttering and reinforcement in :

b) M20 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.

a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforcement cement concrete work in columns, pillars, piers, abutments, post and struts etc up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but exluding cost of centring, shuttering and reinforcement.

b) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete in chajjas exceeding 15mm in thickness upto floor two level including centring and shuttering complete but excluding the cost of reinforcement with 1 : 1.5 : 3( 1 cement: 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in shelves up to floor two level excluding cost of centering and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for :

a) Foundation, footings, bases of columns etc. and mass concrete.

c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

d) Lintels, beams, girders, bressumers and cantilevers etc.

e) Column, pillars, posts and struts etc.

Reinforcement of RCC work including bending, binding and placing in position complete.

b) Tar/TMT Steel

IV. Brick Work

Brick work with best available local bricks in foundation and plinth in cement mortar 1:5 (1 cement : 5 fine sand).

Half brick masonry (with best available local bricks) in cement mortar 1:4 (1 cement : 4 coarse sand) in foundation and plinth.

Extra for half brick masonry in superstructure above plinth level and up to floor two level.

Aluminium Works

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For fixed portion Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) :

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with PVC/ neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-incharge. (Cost of aluminium snap beading shall be paid in basic item) 4.1 With float glass panes of 4.0 mm thickness.

Providing and fixing MS grills of required pattern in wooden frames of windows etc with MS flat, square or round bars with round headed bolts and nuts or by screws.

b) Ornamental grill.

Providing and fixing aluminum sliding door bolts anodised transparent or dyed to required color or shade with nuts and screws etc complete.

Providing and fixing aluminum Tower bolts anodized or transparent or dyed to required color or shade with necessary screws etc complete.

Providing and fixing aluminum Handles anodised transparent or dyed to required color or shade with necessary screws etc complete.

VI. Flooring

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622, of approved make , in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 course sand) including grouting the joints with white cement and matching pigments etc, complete. b) size of tiles 600x600mm

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacture) with water absorption less than 0.08% and conforming to IS: 15622, of approved make , in all colours and shades, skirting, riser of steps, over 12mm thick bed of cement mortar 1:3 (1 cement : 3 course sand) including grouting the joints with white cement and matching pigments etc, complete. b) size of tiles 600x600mm

White glazed tiles 5mm.thick in flooring, skirting, risers of step and dado in 12 mm thick cement plaster 1 : 3(1 cement: 3 coarse sand) painted with white cement slurry.

VII. Roofing

Steel work in built up tubular trusses including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer welded and bolted including special shaped washers etc complete (welding to be paid separately).

Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet roofing fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of purlins, rafters and trusses. Details of cost for 179.655 Sq.m.Laying and fixing 20 sheets in 3 row require Overall sheet area of 20 x 3 x 3.05 x 1.072 plus 3% wastages= 202.061 Sqm After H & L !aping as per manufacturer's specification, effective Area Measurable will be 20 x 3x 2.95 x 1.015 = 179.655 Sqm

Providing and fixing Durashine zinc-Aluminium alloy coated (TATA Bluescope building product) sheet ridges fixed with necessary fasteners and lapping method as described by the manufacturer inclusive of cutting hoisting and fixing complete, excluding the cost of pur!ins, rafters and trusses. Details of cost for 11.75m Laying and fixing 4 lenths of 3.05m each require Overall length of 4 x 3.05 plus 3% wastages= 12.566m After laping as per manufacturer's specification, effective Measurable length will be (4 x 3.05)- (3 x 0.15) = 11.75m

False Ceiling

Providing and fixing 12 mm thick insulating board ceiling of approved quality with necessary nails etc. complete (frame work to be paid separately).

Providing and fixing plain, square edged wooden beading 38 mm x 12 mm section with screws of approved quality for ceiling.

a) Best local approved quality wood.

Extra for chamfered edges in beading

VII. Finishing

12 mm cement plaster 1 : 4 (1 cement : 4 fine sand).

15mm cement plaster 1:5 (1 cement : 5 fine sand) on the rough side of single or half brick wall

6 mm cement plaster to ceiling 1 : 4 (1 cement: 4 fine sand).

Applying one coat of cemenl primer of approved brand and manufacture on wall surface.

Painting two or more coats with enamel paint of approved brand and manufacture in any shade on new work to give an even shade.

Distempering (lwo or more coats) with oil bound washable distemper of approved brand and manufacture and of required shade on new work over and including a priming coat with distemper primer of approved brand and manufacture to give an even shade.

VIII. Miscelleneous

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

X. Water Supply

Providing and fixing GI pipes complete with GI fittings and clamps including cutting and making good the walls (internal work).

a) 15 mm nominal bore

b) 20 mm nominal bore

Providing and fixing GI pipes complete with GI fittings including trenching and refilling etc (external work).

a) 15 mm nominal bore

b) 20 mm nominal bore

d) 32 mm nominal bore

Providing and fixing brass bib cock of approved quality.

a)15 mm nominal bore

Providing and fixing brass stop cock of approved quality.

a) 15 mm nominal bore

XI. Sanitary Installations

Providing and fixing white vitreous china water closet squating pan (Indian type WC pan) size 580 mm with 100 mm and sand cast iron P or S trap, 12.5 Litre high level CI flushing cistern (of approved make) with fittings RS or CI brackets, 32 mm dia galvanized steel telescopic flush pipe with fittings and clamps 20 mm GI over flow pipe with specials and mosquito proof coupling of approved municipal design and GI chain and pull complete including painting of cistern and fittings, cutting and making good the walls and floors where required.

a) Long Pan patten WC Pan

Providing and fixing white vitreous china pedestal type (European type WC pan) water closet with seat and lid with CP brass hinges and rubber buffers, 12.5 Litres white vitreous china low-level flushing cistern with fittings and brackets 40 mm white porcelain in enamel led flush band, 20 mm over flow pipe with specials and mosquito proof coupling of approved municipal design complete including cutting and making good the walls and floors where required.

a) WC pan with white plastic seat and lid.

Providing and fixing white vitreous china wash basin with RS or CI brackets painted white 15 mm CP brass pillar taps and CP brass chain with rubber plug 32 mm CP brass waste of standard pattern, 32 mm dia CP brass trap and MI unions complete, including cutting and making good the walls where required.

b) Flat back wash basin size 550x400 mm with single 15 mm CP brass pillar taps of heavy quality.

Providing and fixing a pair of white vitreous china foot rest of standard pattern for squatting pan WC.

a) 250 x 130 x 30 mm

Providing and fixing 12.5 litres high level CI flushing cistern of approved make with integral fittings such as ball valve, bell, lever, GI chain and pull complete.

Providing and fixing CP brass waste for wash basins and sinks. B)40 mm dia

Providing and fixing 100 mm sand cast iron grating for gulley, fioors or nahni trap.

Providing and fixing 600x450 mm bevelled edge mirror or superior glass (of approved quality) complete with 6 mm thick asbestos sheet ground fixed to wooden cleadt with CP brass screws and washers.

Providing and fixing 600 x 120 mm glass shelf with CP brass brackets and guard rail complete, fixed to wooden cleadts with CP brass screws.

Providing and fixing CP brass towel rail complete with CP brass brackets fixed to wooden cleadt with CP brass screws (heavy quality). a) 750 x 20 mm size

Providing and fixing toilet paper holder. a) CP Brass

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.

a) 100 mm dia

c) 50 mm dia

Providing and fixing UPVC/PVC heel rest sanitary bend.

a) 100 mm dia

c )50 mm dia

Providing and fixing PVC single equal plain junction of required degree with access door, insertion rubber washer 3 mm thick, bolts and nuts complete.

a) 100 x 100 x 100 mm

Providing and fixing PVC trap of self cleansing design with sand cast iron screwed down or hinged grating with or without vent arm complete including cost of cutting and making good the walls and floors.

c) 100 mm inlet and 50 mm outlet

Cost for internal electrification

POINT WIRING

Supply, Installation, testing and commissioning Conduit wiring for lights/ fan socket outlets as per the mode of measurements described in the specifications consisting of - a) Wiring in 25/20 mm Dia 2mm thick HMS ,MMS type of PVC conduit as required. b) 1100V grade PVC insulated Cu FR Wire. c) Insulated or base protective earth d) 1.6 mm thick Outlet boxes and junction box as per manufacturers standard e) All work & materials necessary for wiring a point circuit of any length from the Final Distribution Board to switch board, except where identified. f) Embedding/surface conduits and accessories in walls and floors etc. during construction and / or cutting chases (with chase cutting machine) and making good with finishing of wall after embedding of conduit on walls. g) Switch, socket outlet and necessary blank plates, Face-Plates etc. as required. f) All shuttered type sockets with earth terminal. SITC of moduller type Switch, Sockets ,Faceplates , 1.6 mm thick G.I Back Boxes in walls by Electrical Contractor. Colour / Shade / Type of all switch-socket to be as per the Client / Architech confirmation.

Wiring for primary points from SB to first light point with 3X1.5 sq. mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket, modular plate, suitable GI box Average=5 mtr

Wiring for secondary light point with 3x1.5sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core wire etc as required. Average=3 mtr

Wiring for 16amp 3/5 pin socket outlet Control By 16A switch x 2nos on Same Board independent Location with 2X2.5 sq.mm + 1x 1.5sqmm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box. Average=8 mtr

Wiring for 16amp 3/5 pin socket outlet Control By 16A switch x 1nos on Same Board independent Location with 2X2.5 sq.mm + 1x 1.5sqmm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, socket,modular plate, suitable GI box. Average=8 mtr

Wiring for Two Nos 6amp, 3/5 pin socket outlet Control By Two Nos 6A switch on Same Board independent Location with 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch,socket, modular plate, suitable GI box. Average=4 mtr

Wiring for 1 Nos 6amp, 3/5 pin socket outlet Control By 1 Nos 6A switch on Same Board independent Location with 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch,socket, modular plate, suitable GI box. Average=4 mtr

Wiring for 1 Nos 6amp, 3/5 pin socket outlet Control By 1 Nos 6A switch on lighting switch board with 3X1.5 sq.mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch,socket, modular plate, suitable GI box. Average=0.5 mtr

Wiring for SB to fan point with 3X1.5 sq. mmPVC insulated copper FRLS wire concealed in HMS class PVC conduit with modular switch, fan regulator, modular plate, suitable GI box and 3" deep fan box with hook (conduit & fan cost should be excluded) Average=6 mtr

Wiring for SB to exhuast fan point with 3X1.5 sq. mm PVC insulated copper FRLS wire concealed in HMS class PVC conduit , with modular switch, socket, modular plate, suitable GI box.

Wiring from DB to switch board (submain) wiring alongwith necessary earth wire for the following sizes of PVC insulated copper FRLS wire concealed in HMS class PVC conduit conductor, already laid concealed HMS class PVC conduit as required. (only wiring)

2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 4.0 sq. mm + 1 X 2.5 sq. mm earth wire

2 x 6.0 sq.mm + 1 X 4 sq.mm earthg wire

Supplying and fixing of following sizes of HMS class PVC conduit along with accessories in concealed/surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

LOW VOLTAGE WIRING

LV Wires

Supply, Installation, testing and commissioning Indoors PVC insulated LV Wires on walls, ceiling, cable trays complete with clamps Termination etc

CAT 6 cable data including terminations in already laid conduits.

For Telophone including terminations in already laid conduits. 2 pair 0.5mm

RG -6 cable for TV outlet including terminations in already laid conduit.

RG -11 cable for TV outlet including terminations in already laid conduit.

LV Cables

Supply, Installation, testing and commissioning Indoors multipair 0.5mm dia copper PVC insulated and sheathed, armoured telephone cables on walls, ceiling, cable trays complete with clamps Termination, cable markers etc. from MDF to the various tag blocks as specified and shown on drawings.

10 pair 0.5 mm twisted pair non jelly filled armoured telephone cable

20 pair 0.5 mm twisted pair non jelly filled armoured telephone cable

50 pair 0.5 mm twisted pair non jelly filled armoured telephone cable

100 pair 0.5 mm twisted pair non jelly filled armoured telephone cable

Supplying and fixing of following sizes of HMS class PVC conduit along with accessories in concealed/surface/recess including cutting the wall and making good the same in case of recessed conduit as required.

TTB box with 20 pair krone

LT CABLING SYSTEM

POWER CABLES

Supply and laying heavy duty 1100V grade XLPE insulated sheathed & armoured FRLS cables indoor or outdoor with Cu conductors as specified and shown on drgs. and as per IS 7098- part 1 of 1998 complete with:- a) Cable clamps on walls, columns, beams, cable markers etc. Cable Dressing on Trays,Trenches & HDPE Pipes b) Earthing the glands armouring etc. c) Aluminium tags for all XLPE Al/ Cu cables to be provided.

4c x 1.5sq.mm Cu XLPE Cable

4c x 2.5sq.mm Cu XLPE Cable

4c x 4sq.mm Cu XLPE Cable

3c x 4sq.mm Cu XLPE Cable

TERMINATIONS WITH SINGLE COMPRESSION GLANDS,LUGS & ACCESSORIES

4c x 1.5sq.mm Cu XLPE Cable

4c x 2.5sq.mm Cu XLPE Cable

4c x 4sq.mm Cu XLPE Cable

3c x 4sq.mm Cu XLPE Cable

4c x 6sq.mm Cu XLPE Cable

4c x 10sq.mm Cu XLPE Cable

Supply and laying heavy duty 1100V grade XLPE insulated sheathed & armoured FRLS cables indoor or outdoor with AL conductors as specified and shown on drgs. and as per IS 7098- part 1 of 1998 complete with:- a) Cable clamps on walls, columns, beams, cable markers etc. Cable Dressing on Trays,Trenches & HDPE Pipes b) Earthing the glands armouring etc. c) Aluminium tags for all XLPE Al/ Cu cables to be provided.

3.5C x 120sq.mm AL XLPE Cable

3.5C x 70sq.mm AL XLPE Cable

3.5C x 50sq.mm AL XLPE Cable

3.5C x 35sq.mm AL XLPE Cable

CABLE TRAY

450 mm width X 50 mm depth X 2.0 mm thickness ( Ladder )

300 mm width X 50 mm depth X 2 mm thickness (perforated )

150 mm width X 50 mm depth X 2 mm thickness ( Perforated )

LIGHTING FIXTURES AND FANS

Supply, Installation, testing and commissioning of following light fixtures and fans as per drawings and specifications with all other accessories. The rate shall include all accessories required to complete the installation as required, Earthing of fittings & Connections from the ceiling rose or junction box of the fitting including Flexible Wires,hangers,chains Complete in all respect.

LED 18 W round shape Cielling Mounted

LED 30 W square shape Cielling Mounted 300 x 300mm

80W Cielling Mounted Fan 1200mm Dia

Exhaust Fan 6 inch Ventilation Fan Pure Copper Motor 150 mm

COMMON AREA/STAIRCASE/LOBBY ETC.

Primary Light points Lift lobby in 25mm conduit Average-12mtr

Secondary Light points in 25mm conduit Average-3 mtr

PANELS & DISTRIBUTION BOARDS

Supply, installation, testing and commissioning of cubicle type panels of 14 SWG CRCA sheet steel floor mounted totally enclosed with top and bottom cable entry and suitable for use on 433 V 3 phase 4 wire 50 c/s having 35 KA fault capacity complete and housed with Aluminium/copper bus bar equipments and their accessories including supply and fixing of base channels of 100x50x6mm as required and with following incoming and outgoing switchgear with protection, metering etc. complete as required and as per specification and schematic diagram.

6 WAY TPN-DB LDB

12 WAY SPN GR Floor

EARTHING SYSTEM

Chemical earthing 17,2mm dia 3 mtr long with 50kg BFC Compound With brick workchamber 300 x 300mm

25 x 6 mm G.I.

25 x 3 mm G.I.

8 SWG G.I earth wires

8 SWG Cu earth wires

Add Carryin Charges

Add Side Development

Cutting of Trees, including Cutting of Trunks, Branches and Removal (Cutting of trees, including cutting of trunks, branches and removal of stumps, roots, stacking of serviceable material with all lifts and up to a lead of 1000 mtrs and earth filling in the depression/pit.)

Clearing Grass and Removal of Rubbish

Excavation in Soil by Manual Means. (Excavation for roadway in soil using manual means including loading in truck for carrying of cut earth to embankment site with all lifts and lead upto1000 metres.)

Excavation in ordinary rock by manual means (Excavation in ordinary rock using manual means including loading in a truck and carrying of excavated material to embankment site with in all lifts and leads upto 1000 metres )

Bankingexcavated earth in layers not exceeding 20 cm in depth breaking clods, watering, rolling each layer 1/2 tonne roller or wooden or steel rammers and rolling every 3rd and topmost layer with power roller of minimum 8 tonnes and dressing up in embankments for roads, flood banks, marginal banks and guide bunds etc. lead upto 50 m and lift upto 1.50 m.

Add Septic Tank(100 User)

Earth work in excavation in foundation and trenches in soils containing 50% or more of shingle or small size boulders upto 30 cm size, lift upto 1.50 m and stacking the excavated soil not more than 3 m clear from the edge of the excavation and returning t

Re-filling excavated earth in foundations and plinth etc. in 15 cm layer including ramming and watering etc. complete.

Providing and laying cement concrete 1 : 3 : 6 ( 1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) excluding the cost of centring an shuttering in a) Foundations and plinth

Reinforced cement concrete in suspended floors, roofs, landings and balconies upto floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centring and shuttering and reinforcement with 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Reinforced cement concrete work in lintels, beams and bresumers up to floor two level including finishing and plastering the exposed surface with cement mortar 1 : 3 (1 cement : 3 fine sand) of thickness not exceeding 6 mm to give a smooth and even surface but excluding cost of centering, shuttering and reinforcement.

a) 1 : 1.5 : 3 (1 cement : 1.5 coarse sand : 3 stone aggregate 20 mm nominal size).

Centring and shuttering including strutting, propping etc and removal of form work for :

a) Foundation, footings, bases of columns etc. and mass concrete.

c) Suspended floors, roofs, landings shelves and their supports, balconies and chajjas (3.5 m height).

Reinforcement of RCC work including bending, binding and placing in position complete.

b) Tar/TMT Steel

Brick work with best available local bricks in foundation and plinth in cement mortar 1:3 (1 cement : 3 fine sand).

40 mm thick red oxide flooring, under layer of 30 mm thick cement concrete 1 : 2 : 4 (1cement: 2 coarse sand : 4 stone aggregate 12.5 mm nominal size) & top layer of 10 mm thick plaster of cement red oxide mix (using 3.5 kg of red oxide of iron per 50 kg of cement) 1 : 3 (1 cement red oxide mix : 3 coarse sand) finished with a floating coat of neat cement red oxide mix of same proportion.

Cement plaster skirting (up to 30 cm height) with cement mortar 1 : 3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, including rounding of junctions with floor. a) 18 mm thick

Providing and fixing sand cast iron/ cast iron (spun) soil, waste and vent pipes.

a) 100 mm dia

Making soak pit 2.50 m dia 3 m deep with 45 x 45 cm dry brick honeycomb shaft and SW drain pipe 100 mmdia 1.80 m long complete,as per standard design.

M/s Salo Enterprises (BID ID -8298)