SPL REPAIR TO BLDG NO T-2 LOC AT OFFRS MESS AREA OF 4 CSR AND PROVN OF SOLAR PV GENERATION AT BIHUGURI STN UNDER GE (S) TEZPUR

Amount

Dismantling asbestos cement corrugated semi corrugated etc sheets in roof covering.Complete all as specified and as directed by Engineer-in-charge.

Dismantling wrought iron or mild steel work or any description as in door, gates, etc and similar works .Complete all as specified and as directed by Engineer-in-charge.

Taking down chowkats or frames not exc 1.5sqm each with shutters( without taking off shutters from the frame ) including dismantling of old bed blocks for hold fasts.Complete all as specified and as directed by Engineer-in-charge.

Taking down chowkats or frames exc 1.5sqm and not exc 4.0 sqm each with shutters ( without taking off shutters from the frame ) including dismantling of PCC bed blocks for hold fasts.Complete all as specified and as directed by Engineer-in-charge.

Taking down cement plaster, of any description on brick or stone walls, etc including racking out joints, hacking for key, scrubbing down with water .Complete all as specified and as directed by Engineer-in-charge.

Dismanting timber scantling 40 Sqcm and over in secion in any position in framed work or unframed work.Complete all as specified and as directed by Engineer-in-charge.

Demolition of reed lathing, single or double including battens and plasters or checken wire lathing.Complete all as specified and as directed by Engineer-in-charge.

S&F 0.50 mm thick pre-painted galvatume aluminium zink coating GI based corrugated steel sheet of approved colour having tensile stenght of 550 MPA as in roof covering,including end creep at sloping end of creep length 200 mm to 250 mm etc fixed with self tapping screws as specified and as directed by Engineer-in-charge. Note :- Creep length shall be measured and paid in the same item.

S&F pre-painted galvalume aluminium zink coating GI based plain steel sheet 0.50 mm thick of an colour having tensile stenght of 550 MPA as in ridge, valley and eaves Board fixed with self tapping screws .Complete all as specified and as directed by Engineer-in-charge.

Dismantling wall/ceiling board (fibre pulp insulation ) or insulation boards any thickness including cover fillets.Complete all as specified and as directed by Engineer-in-charge.

S&F Exposed GI powder coated snap grid frame for false ceiling 600x600mm size of wall angle 25x25x0.35mm size of cross tee and main tee 25x25x0.25mm and 32mm x 24mm x 0.25mm with 1.5mm dia double GI suspentor including supply and fixing of 4mm thick Eco Board decorative type in false ceiling including fixing arrangement from steel tress any type of truss.Complete all as specified and as directed.

M&L 2nd class HW in scantling fixed clean swan in framed work.Complete all as specified and as directed

M/L PCC 1:3:6 type C1 20mm grade aggregate as in , coping/hold fast or similar work.Complete all as specified and as directed

S&F MS framed works such as grills grating etc with ends of bars shouldered and for rivetted in forged into spikes, framed guard bars, railing and similar work confiring to Fe-410-0 or Fe 310-0 complete all as specified and directed

S&F solid PVC door frame of size 50mm X 47mm, made out of 5mm plain colour PVC sheet reinfoced with M.S. square tube, supply and fixing in opening as per specification.

Supply and fix, 30 mm thick factory made solid panel PVC shutters (conforming to IS : 4020) consisting of frame made out of mild steel tubes of 19 gauge and size 19 mm x 19 mm for stiles and 15 mm x 15 mm for top and bottom rails. Mild steel frame shall have a coat of steel primer and covered with PVC channel size 30 mm x 50 mm forming stiles and 5 mm thick 75 mm wide PVC sheets for top rail, lock rails, bottom rail on either side and 10 mm thick 20 mm wide cross PVC sheets as gap insert for top rail and bottom rail, panneling of 5 mm thick PVC sheet to be fitted in mild steel frame welded/sealed to the stiles and rails with 30 mm wide x 5 mm thick PVC sheet beading in either side and joint together with solvenet cement adhesive etc an additional 5 mm thick PVC strip of 20 mm width to struck on the interior side of the ‘C’ channel using PVC solvent adhesive including and fitted to PVC door frame all as specified and directed.

S&F of joist, channel, angle, flat iron or Tee sections, fixed independently with connecting plates, etc confirming to Fe 410-W(Gde -E-250 quality A) complete all as specified and directed.

S&F 30 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides.Complete all as specified and as directed by Engineer-in-charge.

S&F 35 mm thick 2nd class hard wood Glazed and skelton shutter(minimum three panel) open rebated and prepared to receive glass, gauze etc edges of the framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc sizes of members as specified all as specified and directed

S&F MS 250 mm ordinary door spring including roller and roller plate.Complete all as specified and as directed

S&F 100mm Butt hinges medium weight cold rolled mild steel .Complete all as specified and as directed

S&F 2nd class hard wood small fitting such as brackets of any type latch and hinge blocks,shaped door and window stops and the like including all necessary labours articles n.exe 200 cu.cm each.Complete all as specified and as directed by Engineer-in-charge.

S&F Butt hinges medium weight cold rolled mild street and fixed size of hinges 50mm.Complete all as specified and as directed

S&F 150mm long aluminium handle, cast type, anodised .Complete all as specified and as directed

S&F floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, overall length of 140mm fixed with screwes all as apecified and directed.

S&F Aluminium anodised barrel tower bolts of extruded section 150 mm long and fixed with screws.Complete all as specified and as directed

S&F Aluminium anodised barrel tower bolts of extruded section 200 mm long and fixed with screws.Complete all as specified and as directed

S&F Aluminium anodised sliding door bolts of size 250 mm long, with hasp & staple ( bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extreded sections or cast aluminium alloy.Complete all as specified and as directed

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing, removing rubbish off the complete all as specified and directed.

M&L Vitrified Ceramic tiles 10 mm thick (square/ rectangular) any shade, polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in CM 1:4.Complete all as specified and as directed

All as per item No 30 above but in skirting over 10mm thick screeding in cement mortar 1:3,Complete all as specified and as directed by Engineer-in-charge.

S&F Coloured Glazed ceramic tiles 450 x 300 mm x 7mm thick, in skirting /dado etc set and jointed in neat cement slurry and pointed in white or coloured cement to match over 10mm screeding in Cement mortar 1:3 .Complete all as specified and as directed by Engineer-in-charge.

Non - skid Ceramiccoloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm thick screed bed in cement mortar (1:4) complete all as specified and as directed

Non - skid Ceramiccoloured tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.18 sqm but not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15mm tick creed bed in cement mortar (1:4) complete all as specified and as directed

All as per item No 34 above but in skirting over 10mm thick screeding in cement mortar 1:3

Supply and fix, as in repair, vitreous china wash down water closet pan (Pedestal pattern) white (excluding flushing cistern )but including seat cover white closed type and flush pipe complete all as specified and directed

Supply and fix, as in repair, vitreous china wash basin, white, oval type size 550 x 400 mm, excluding taps, waste chain, plug and porcelain stopper but including brackets, with anchor bolts 2 Nos cutting for and pinning in ends of bracket or erecting stand complete all as specified and directed.

S&F in repair brass chromium plated bottle traps 32mm bore for wash basins with inlet and outlet screwed for pipe or connectionsincluding necessary packing, union and cap and fixed complete all as specified and directed

Supply and fix, waste coupling CP 32 mm dia for glazed ware basins etc with fly nuts flanged etc complete all as specified and directed.

S&F in repairs PVC connections 15mm size with PTMT nut of length 450mm complete all as specified.

Supply and fix, as in repair, 10 ltrs capacity PVC valve less syphonic action type, low level flushing cistern, white, with inlet, ball valve float and handle with 32 mm dia flush pipe including brackets complete all as specified and directed.

S&F of 15 mm bore tubes medium grade galvanised with and incl all GI fitting (such as bends, elbows, Tees, connectors, short pieces, back nuts, unions, caps and plug etc ) and fixed complete to wall and ceiling or laid in/on floor inlcuding taking up or down complete all as specified and directed,

S&F of 20 mm bore tubes medium grade galvanised with and incl all GI fitting (such as bends, elbows, Tees, connectors, short pieces, back nuts, unions, caps and plug etc ) and fixed complete to wall and ceiling or laid in/on floor including taking up or down complete all as specified and directed,

S & F in repairs wall mixer 3-in-1 CP 15 mm bore including 100 to 125 mm dia overhead shower, complete with 15 mm long bend pipe and wall flenge including making good wall surface with matching tiles complte all as specified and directed

Supply and fix,as in repair,15 mm bore pillar tap, fancy type cast copper alloy, with capstan head, chromium plated, screwed down high pressure, with or without letter Hot or Cold with long screwed shanuls and fly nuts, screwed for iron pipe or for brass ferrule all as specified and directed.

S&F in repair 15mm bore two way bib cock cast copper alloy CP Fancy type ,with wall flange screwed down for iron pipe or union , complete all as specified and directed. Make: Jaquar or Equivalent approved by GE

Supply and fix,as in repair, 15 mm bore bib taps, cast copper alloy,cromium plated, fancy type, with crutch or butter fly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified and directed.

Supply and fix, as in repair, angle cock, cast copper alloy, fancy type, chromium plated with long shank and cup (concealed type) screwed down high pressure, with crutch or butterfly handles for 15 mm bore pipe or for unions all as specified and directed.

S & F in repairs Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.20 to 1.50 metre long flexible tube and ABS wall hook including making connections and fixed in position Complete all as specified and as directed

S&F composite 100% solid wood plastic complete (single extended process) material with density not less than 780 kg/cum and plastic wood as in wood chowkhat complete all as per manufacturer instruction.Complete all as specified and as directed by Engineer-in-charge.

S&F in repair tubular Towel rail chromium plated 600mm long 20mm dia D type complete all as specified and as directed.

S&F in repairs Soap dish, any type, fixed to plugs with chromium plated brass screws complete all as specified and directed.

S& F in repair of Towel Ring of stainless steel fixed and including Chromium plated brass screws complete all as specified and directed.Make-

S & F in repairs Toilet paper holder of brass chromium plated fixed to walls with chromium plated(CP) brass screws.

Dismantling and breaking up PVC drain pipes of any dia jointed in CM and taking out of trenches.Complete all as specified and as directed by Engineer-in-charge.

Supply and fix, 110mm bore PVC (SWR)pipe single socketed with rubber ring joints fixed to walls or laid in trenches or floor all as specified and directed.

Supply and fix, 75 mm bore PVC (SWR)pipe single socketed with rubber ring joints fixed to walls or laid in trainches or floor all as specified and directed.

S&F for PVC (SWR) with access door bend 110mm dia.Complete all as specified and as directed

S&F for PVC (SWR) with access door bend 75 mm dia.Complete all as specified and as directed

S&F in repair PVC(SWR) junction single (single 'T') equal or unequal 75 mm bore.Complete all as specified and as directed

S& in repair FPVC (SWR) junction single (single 'T') equal or unequal 110mm bore.Complete all as specified and as directed

S&F Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified

S&F Anodised aluminium window and ventilator shutters, sliding type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, inlcuding locking arrangment anodised aluminium snap beading, screws etc.complete all as specified

S&F 4 mm thick plain glass in square not exc 0.50 sqm in each pane complete all as specified and directed.

S&F 4 mm thick figured glass, pin head type in square or rectangle not exc 0.50 sqm in each pane complete all as specified and directed.

S&F Stainless steel wire cloth.0.36 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with stainless steel wire staples.complete all as specified

M&L Reinforced cement concrete 1:1/2:3,A-1 Nominal mix(20 mm aggregate) including rafts footings, foundation beams, plinth beam base for column etc basement slab, under reamed piles and mass concrete .complete all as specified

M&L Reinforced cement concrete 1:1/2:3,A-1 Nominal mix (20 mm graded aggregate) as in coloumn, pillar, pier, posts etc .complete all as specified

Use & waste form work for flat fair finished surfaces of concrete foundation, footings, bases of columns and plinth beam and similar work.complete all as specified

M&L TMT bars 5mm dia and over up to and including 10 mm as in stirrups, spacers and binders cut to length, bent to shape required including cranking bending spirally for hoping for columns, hooking ends and binding with mild steel wire (annealed) not less than 0.9 mm dia or securing with clips .complete all as specified

M&L TMT bars 10 mm dia and over cut to length, bent to shape required including cranking bending for columns, hooking ends and binding with mild steel wire .complete all as specified

Use & waste form work to sides of pillars,posts, struts, piers, columns and stanchions for rough finished surfaces of concrete.complete all as specified

Demolition of brick work/stone masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlars facings, dressed stone work and pre-cast concrete articles all as directed.

Material and labour for old size fly ash best quality bricks, straight or curved on plan exc 6 m mean radius built in cement mortar ( 1:6) having compressive strenght not less than 75 kg/Sq cm.complete all as specified

Material and labour for old size fly ash best quality bricks, straight or curved on plan to any radius in half brick thick wall built in cement mortar ( 1:6) having compressive strenght not less than 75 kg/Sq cm all as specified and directed.

M & L, 15mm thick rendering in C.M. (1:4) on fair faces of brick work finished even and fair without using extra cement .complete all as specified

M & L, 10mm thick rendering in C.M. (1:6) on brick work finished even and fair without using extra cement .complete all as specified

M&L 15mm thick rendering in CM (1:4) on one side of lathing finishedd even and fair including 0.71mm chicken wire and size of mesh 12mm.Complete all as specified and as directed by Engineer-in-charge.complete all as specified

M&L 10mm thick rendering in CM (1:6) on other side of lathing finished even and fair .complete all as specified

M&L Applying two coats of Acrylic emulsion distemper to newly plastered/previously untreated wall over a coat of 1 mm layer wall care putty over a coat of primer including preparation of newly platsered wall .complete all as specified and as directed.

M&L Applying two coats of Acrylic emulsion distemper to old surfce wall over a coat of 1 mm layer wall care putty over a coat of primer including complete removal of existing treatment all as specefied and directed.

M&L preparation of newely plaseter sufaces and appplying one coats of weather coat (Acrylic exterior paint) over a 1 mm thick layer of putty and one primer coats of damp shealth to new plastered walls as per manufacturer and apllied by approved applicator complete all as specified and directed.

M&L complete removal of existing treatment and appplying one coats of weather coat (Acrylic exterior paint) over a 1 mm thick layer of putty and one primer coats of damp shealth to old plastered walls as per manufacturer instrcution including properly fillings the cracks and apllied by approved applicator complete all as specified and directed

Demolition cement concrete (unreinforced) n'exc 15 cm thick (below or above ground level) as directed.

M&L 75 mm thick plain cement concrete (1:3:6) type C1 using 20mm graded stone aggregate as in plinth protection & footpath etc and finishing surfaces of concrete even and smooth including making construction joint at interval of 1.5 mtr and every corner and filled with bituminous filler complete all as specified and as directed.

M&L 50 mm thk cement concrete type B1, (1:4:8) (20mm graded stone aggregate) as in sub bases, floors and Pavings.Complete all as specified and as directed by Engineer-in-charge.

M&L preparation of old painted wooden surfaces over 10cm width or girth and applying one coat of synthetic enamel paint.

M&L preparation of old painted steel surfaces over 10cm width or girth and applying one coat of synthetic enamel paint.

M&L preparation of new wooden surfaces over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer.Complete all as specified and as directed by Engineer-in-charge.

M&L for preparation of new steel surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

Supply and fix, fancy type curtain rod aluminium anodised of 20-25 mm dia including sofia braket of any approved colour and design with fixing brackets, stops, rollers etc all as specified and directed.

Supply and fix, as in repairs, sheet glass self assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with cromium plated bracket guard and railing 60cm long all as specified and directed.

M&L in repairs for PVC(SWR) gully trap 125/110 mm setting and jointing with solvent

Demolition of reinforcement cement concrete as in columns and similar work complete all as specified and directed.

M&L for vitrified parking tiles of size 300 x 300 x 10 to 12 mm thick with grey cement and pigment, set and jointed and pointed in neat cement slurry in floors laid over & including 15 mm thick screed bed in cement mortar 1:6 all as specified and as directed.

M&L for PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in surface channels, drains including all necessary form work complete all as specified and directed.

M&L in repairs Prelaminated particle board 18/19 thk, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work

S & F 100 mm long hasp and staple aluminium anodised wire type ,incl bolt to hinge plate and fixed with screw complete all as specified and directed.

S & F continuous(Piano) hinges 30 mm width mild steel ,bright finish fixed with screw complete all as specified and directed.

S & F 40 mm dia cupboard knob fixed with nut ,screw and washer of brass polished complete all as specified and directed.

Material and labour for 75/110 mm dia of outlet PVC(SWR) floor trap, plain with granting including jointing with solvent cement all as specified and directed

M&L Extra for forming fair finished drain or channel 30 CM inner girth in cement concrete,using extra cement including forms moulds,mitred/stopped ends etc.Complete all as specified and directed

Taking down carefully unserviceable point wiring (light,fans,socket etc) complete incl battens and fittings such as switch, ceiling rose,light fittings, regulatos, socket etc and making good disturbed surface of wall/floor etc complete all as specified.

Taking down DB/main switch of any size and making good disturbed surface of wall/floor complete all as specified.

M & L for point wiring for one light point with 1.5 sqmm cable PVC insulated copper conductor multi stranded as per IS-694 FRLS cable controlled by one way switch, drawn through and including PVC casing caping with all accessories incl 1.5 sqmm multi strand copper conductor cable (green colour) PVC insulated and unsheathed for earth continuity connected to common earth dolly and sunken cast pressed steel terminal box fixed flush to wall of not less than 1.6 mm thick for mounting of fittings such as modular switches, sockets and regulators with Modular PVC flush box and Modular White Cover plate with frame all as specified and directed including taking down old unserviceable point wiring

All as per Ser item No.106 above but for one ceiling fan point all as directed

All as per Ser item No.106 above but for one exhaust fan point all as directed

All as per Ser item No.106 above but for one bell point all as directed

All as per Ser item No.106 above but for 5 amps socket on same board with other switches

All as per Ser item No.106 above but for 5 amps socket on independent board.

All as per Ser item No.106 above but with 2.5 sqmm cables for 15 amps switch socket combination outlet on independent board complete all as specified and directed.

All as per Ser item No.106 above but with 4.0 sqmm cables for 15 amps switch socket combination outlet (AC Point) on independent board complete all as specified and directed.

Supply and fix in replacement of Modular switch 1 way 6A, 1 module

Supply and fix in replacement of Modular Bell push 6A 1 module

Supply and fix in replacement of Buzzer, Ding Dong AC. 230 volts, single pole

Supply and fixin replacement of Modular Socket, 6A - 2/3 pin combined 2 module,

Supply and fix in replacement of Modular switch 1 way 16A, 1 module

Supply and fix in rfeplacement of Socket 6A/16A - 2/3 pin combined 2 module,

Supply and fix in replacement of Single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 32 Amps all as directed

Supply and fix in replacement of ceiling rose surface backelite 65x50 mm having 3 terminals.

S & F in replacement of Modular Fan step regulator, 120W - 2 module all as specified and directed

Supply and fix in replacement of Lamp holder, PVC/Polycarbonate type with back plate suitable for batten fittings all as directed

Supply & fix in replacement of Basic all purpose surface and wall mounted LED batten with Aluminum housing & integrated electronic driver. Item description: LUMILINEPLUSBS20WLED865SPCSS of Make: Havells or equivalent make of Phillips/Bajaj/Surya/CG

Supply and fix in replacement of ceiling light LED Recessed full luminaire with glare free uniform illumination 600 mm x 600 mm,24 watts,complete all as specified and directed Make: CG,Cat No-LCTLRNE-24-FO-TL or equivalent make of Phillips/Bajaj/Surya/Havells

Supply and fixing in replacement of LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminum hosing and heat resistant complete with driver, lamp bracket with impact and corrosion resistant including thermal management in multiple optics complete with IP 65/66 protection complete with GI Pipe 40 mm dia bracket made out 120 degree in shape with 2 No GI strip clamps, nut bolts and washers all as directed

Supply and fix in replacement of Decorative wall light made up of high grade engineering plastic material suitable for 20 Watt LED bulb including 20 watt bulb all as directed

Supply and fixing ceiling fans complete with blades, down rods, electronic regulator and accessories, 230 V, not more than 50Watt, 1200 mm sweep. Min air delivery 210 CFM with service value 6.00 BEE. Five star rated with brushless direct current motor (BLDC) including provision of fan hook all as directed

Supply and fix exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm with making hole on wall surface all as drected

Supply and fix electric water heater, storage type and heating element upto 2 KW capacity 25 litre, BEE 5 Star rated complete with all accessories such as safety valve, thermostate, NRV, stainless steel connection pipes (Hot & Cold), Nut bolts, washers etc all as directed

Supply and fix in replacement of TP&N Vertical Loadline DBs are fitted with Bus Bars, Neutral Links, Blanking Plates (without MCCB), 4 way, SINGLE DOOR SUITABLE FOR TP/FP ‘G FRAME’ MCCB, Cat No DHDLVSRWGOFO04 of Make: Havells or equivalent make of Legrand/L&T/ABB

Supply and fixing in replacement of MCCB 4 Pole, 415 V, fixed type, 25 to 100 Amps with breaking capacity 16 KA

S & F in replaacemetn of MCB DB Single pole and neutral 8 way Single door with 200 amps rated bus bar complete.

Supply and fixing in replacement of 240V, 10KA 'C' curve miniature circuit breaker (MCB) of Single pole and Neutral and current carrying capacity 40 Amp in the MCB DB complete with connection testing and commissioning complete all as specified and directed. Make: Havells/Legrand/L&T/Merlin Gerin/Standard/HPL

Supply and fixing in replacement of 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single pole and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning completed all as directed. Make: Havells/Legrand/L&T/Merlin Gerin/Standard/HPL

Supply and fixing in replacemetn of 240V, 10 KA 'B' curve miniature circuit breaker (MCB) of single pole and current carrying capacity 40 AMP, in the MCB DB Complete with connection testing and commissioning. completed all as specified and as directed. Make: Havells/Legrand/L&T/Merlin Gerin/Standard/HPL

M/L for Earthing complete with galvanised steel earth plate electrode 60×60cm.× 6mm thick, buried directly in ground (earth pit not less than 2.25 metres deep below ground level) with top edge of the plate not less'than 1.5 metres below normal ground level, connected to galvanised earth lead wire 4.0mm dia by means of bolts, nuts, check nuts and washers of galvanised iron or steel all as shown in electrical plate No. 3 connected to earthing test point all as specified or indicated including testing on completion all as specified or indicated including excavation and earth work and testing on completion including takingdown old unsv earthing all as directed

S & F in replacement of MCB DB Single pole and neutral 4 way Single door with 200 amps rated bus bar complete including taking down old unsv DB .completed all as specified and as directed.

S&F in replacement of XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross-sectional area 35 sq mm 4 core.completed all as specified and as directed.

Supplying and fixing PVC insulated,XLPE armoured, heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 10 sq mm, 2 core.completed all as specified and as directed.

Supply and Laying XLPE insulated, armoured heavy duty electric cable with aluminium conductor, 1100 volts grade, cross sectional area 16 sq mm 4 core.completed all as specified and as directed.

Excavation in trenches n.exc 1.5 mtr wide and n exc 1.5 mtr in depth and getting out in soft/ loose soil for laying cables, etc. complete all as specified and as directed.

Returning, filling including spreading, levelling, watering and well ramming in layers n.exc 25 cm in soft/loose soil complete all as specified and as directed.

Removing surplus excavated soil n.exc 50 mtr and depositing where directed at a level n.exc 1.5 mtr above the starting point complete all as specified and as directed..

M&L for sand cushioning with clean dry sand for protection of under ground cable complete all as specified and as directed. Note :- Punned thickness of sand layer shall be measured abd paid to contractor.completed all as specified and as directed.

M&L for Brick Sub Class 'B' locally available best quality laid in trenches with width equal to length of the bricks, above sand cushioning for cable protection complete all as specified and as directed.

Supply, lay and fix in replacement of 40 mm bore galvanized iron water tubing low grade including all fittings and fixed/ laid in trenches or on poles complete all as specified and directed.

Supply and fixing 340 watt (350-325 Watt Range) Multi-Crystaline solar PV module, suitable for On-grid rooftop solar generation, 100% EL tested to minimise micro crack, certified for IEC 61215.completed all as specified and as directed. Make:- Vikram Solar/ Tata Power solar system/Bharat Electronics Ltd/Mundra Solar PV Ltd/ORB Energy Pvt Ltd, Or equivalent A-Grade MNRE Approved (Make In India).

Supply and fix 25 KVA/350 V solar PCU-Three phase with MPPT charge controller and IGBT technology, 98.8% Max effciency, 200v-1000v input voltage range, colour LCD screen display, IP-65 rated for outdoor installation,multiple protection function, Anti resonance, single transformer can connect 6M+ in parrallel. PCU have three modes (Smart mode, Hybrid mode, PCU mode). Make:- Solis-25K, Power One,Or equivalent approved make by MNRE

M&L for solar mounting structure with SS304 Nut bolts, it should be hot deep galvanize above 80 microns. Suitable for mounting of 75 nos 350 watt solar PV module on roof, complete with all accessories nuts, bolts, washers.completed all as specified and as directed.

S&F for annealed tinned copper conductor, crosslinked polyolefin, zero hylogen insulation, UV resistant, TUV certified solar DC cable single core 4 sq mm.completed all as specified and as directed. Make:- Havells, Polycab, Finolex, KEI.

S&F for annealed tinned copper conductor, crosslinked polyolefin, zero hylogen insulation, UV resistant, TUV certified solar DC cable single core 10 sq mm.completed all as specified and as directed. Make:- Havells, Polycab, Finolex, KEI.

S&F for annealed tinned copper conductor, crosslinked polyolefin, zero hylogen insulation, UV resistant, TUV certified solar DC cable single core 16 sq mm.completed all as specified and as directed. Make:- Havells, Polycab, Finolex, KEI.

S&F rigid non metallic PVC Conduit medium grade complete with junction boxes, tees, bends elbows, reducers, saddles and all fixing accessories of size 20 mm dia. Make:- Richa/Prestoplast

S&F rigid non metallic PVC Conduit medium grade complete with junction boxes, tees, bends elbows, reducers, saddles and all fixing accessories of size 25 mm dia. Make:- Richa/Prestoplast

S&F rigid non metallic PVC Conduit medium grade complete with junction boxes, tees, bends elbows, reducers, saddles and all fixing accessories of size 40 mm dia.completed all as specified and as directed. Make:- Richa/Prestoplast

S&F MC4 connectors as per site requirement, ISI marked, suitable for connection of solar cable.completed all as specified and as directed.

M&L for PCC type C1 (1:3:6) with 20 mm graded stone, suitable for foundation filling etc.completed all as specified and as directed.

Material and labour for earthing complete with copper earth plate electrode 600 mm x 600 mm x 3.15 mm thick burried directly in ground (earth pit not less than 2.25 metres deep below normal ground level) with top edge of plate not less than 1.5 metre below normal ground level connected to copper earth strip 20 X 3 mm size by means of steel bolts, nuts, check nuts and washers all as shown in electrical plate no 3 of MES Schedule Part-I connected to earthing point and testing on completion with and including 40 mm bore light grade G.I. protection pipe (upto 7.5 metre beyond outer edge of earth pit) PCC pit in mix 1:3:6 type C1 with RCC 1:2:4 type B-1 40 mm thick cover reinforced with 6 mm dia M.S bars 3 nos both ways with lifting hook made out of 6 mm dia bar, watering arrangement with funnel and wire mesh and 20 mm bore light grade G.I. watering pipe, common salt and charcoal filling, necessary excavation and earth work complete.

M&L for copper strip 20mm x 3.15 mm with saddles, insulators (2 Nos in 1 RM) and fixing screws etc. for roof conductors and down conductors above ground.

S&F air termination, single pointed, copper rod 12 mm dia and 300 mm long.

M&L for chemical earthing complete with copper earth plate electrode 60 cm x 60cm x 5mm burried in ground surrounded by charcoal, magnesium sulphate in alternate layers. Earth electrode should be connected with copper strip of size 32 mm x 5 mm by brazing and connected to test point. 15 mm bore medium GI tubing for watering with funnel and 40 mm dia GI pipe for protection of earth strip up to 7.5 mtrs. Earth pit shall be made of PCC 1:3:6 type C-1 with CI cover all as shown in electrical plate no. 03. Note:- 1. Earth resistance should be less than 1 ohm. 2. Earth work (Excavation, Removal & returning filling) will be included in the quated rate. 3. GI pipe 40 mm dia med grade up to 7.5 Mtrs included in the above quated rate. Note 1:-The contract sum shall be arrieved at after deducting amount of schedule of credit from the total quated amount. Note 2-Contractor's supervisor and main worker would wear shirt/T-shirt of colour sky blue/brown/yellow preferable embosed with contractor's firm name while carriying out any activities in defence area for better check of security purpose.

M/S LAKSHMI ENTERPRISES

M/S Deep-Jeet

M/S Manjit Singh

M/S Bharat Construction Co.

Anil Kumar Sarmah

sanjay upadhya

M/S MOHANPASARI